Tascam CD-200IL Owners Manual

CD-200iL

CD Player / iPod Dock

OWNER’S MANUAL

D01206220B

IMPORTANT SAFETY PRECAUTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For Canada

WARNING: TO PREVENT FIRE OR

SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.CET

APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB-003 DU CANADA.

For U.S.A.

This equipment complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause interference and

2) This device must accept any interference, including interference that may cause undesired operation of the

device.

INFORMATION TO THE USER

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user's authority to operate this equipment.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

CE Marking Information

a) Applicable electromagnetic environment: E4

b) The average half-cycle r.m.s. inrush current

1. On initial switch-on : 0.48 Arms

2. After a supply interruption of 5s : 0.29 Arms

For the customers in Europe

WARNING This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Pour les utilisateurs en Europe

AVERTISSEMENT Il s'agit d'un produit de Classe A. Dans un environnement domestique, cet appareil peut provoquer des interférences radio, dans ce cas l'utilisateur peut être amené à prendre des mesures appropriées.

Für Kunden in Europa

Warnung Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen versursachen; in diesem Fall kann vom Betrieber verlang werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.

This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records.

Model number

Serial number

TASCAM CD-200iL

DECLARATION OF CONFORMITY

We, TEAC EUROPE GmbH. Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany declare in own responsibility, the TEAC product described in this manual is in compliance with the corresponding technical standards.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

The apparatus draws nominal non-operating power

• from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position. The mains plug is used as the disconnect device, the

• disconnect device shall remain readily operable.

Caution should be taken when using earphones or

• headphones with the product because excessive sound

pressure (volume) from earphones or headphones can cause hearing loss.

If you are experiencing problems with this product,

• contact TEAC for a service referral. Do not use the prod-

uct until it has been repaired.

CAUTION

Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as

• vases, on the apparatus.

Do not install this apparatus in a confined space

• such as a book case or similar unit.

The apparatus should be located close enough to

• the AC outlet so that you can easily grasp the power

cord plug at any time. If the product uses batteries (including a battery

• pack or installed batteries), they should not be

exposed to sunshine, fire or excessive heat. CAUTION for products that use replaceable lithium

• batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace only with the same or equivalent type.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

RACK-MOUNTING THE UNIT

Use the supplied rack-mounting kit to mount the unit in a standard 19-inch rack, as shown below.

Remove the feet of the unit before mounting.

CAUTION

•

Leave 1U of space above the unit for ventilation.

•

Allow at least 10 cm (4 in) at the rear of the unit for ventilation.

TASCAM CD-200iL

Safety Information

For U.S.A

CAUTIONS ABOUT BATTERIES

This product uses batteries. Misuse of batteries could cause a leak, rupture or other trouble. Always abide by the following precautions when using batteries.

Never recharge non-rechargeable batteries. The

• batteries could rupture or leak, causing fire or injury.

When installing batteries, pay attention to the polarity

• indications (plus/minus (+/–) orientation), and install

them correctly in the battery compartment as indicated. Putting them in backward could make the batteries rupture or leak, causing fire, injury or stains around them.

When you store or dispose batteries, isolate their

• terminals with insulation tape or something like that

to prevent them from contacting other batteries or metallic objects.

When throwing used batteries away, follow the dispos-

• al instructions indicated on the batteries and the local

disposal laws.

Do not use batteries other than those specified. Do not

• mix and use new and old batteries or different types of

batteries together. The batteries could rupture or leak, causing fire, injury or stains around them.

Do not carry or store batteries together with small

• metal objects. The batteries could short, causing leak,

rupture or other trouble.

Do not heat or disassemble batteries. Do not put them

• in fire or water. Batteries could rupture or leak, causing

fire, injury or stains around them.

CAUTIONS ABOUT LASER RADIATION

This product has been designed and manufactured according to FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968,” and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings.

The label required in this regulation is shown at 1.

Cautions:

•

DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER.

•

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

•

IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE PRODUCT IN ITS DAMAGED STATE.

If the battery fluid leaks, wipe away any fluid on the

• bat tery case before inserting new batteries. If the

battery fluid gets in an eye, it could cause loss of eyesight. If fluid does enter an eye, wash it out thoroughly with clean water without rubbing the eye and then consult a doctor immediately. If the fluid gets on a person’s body or clothing, it could cause skin injuries or burns. If this should happen, wash it off with clean water and then consult a doctor immediately.

The unit power should be off when you install and

• replace batteries.

Remove the batteries if you do not plan to use the unit

• for a long time. Batteries could rupture or leak, causing

fire, injury or stains around them. If the battery fluid leaks, wipe away any fluid on the battery compartment before inserting new batteries.

Do not disassemble a bat tery. The acid inside the

• battery could harm skin or clothing.

Optical pickup

Type: EP-C101 Manufacturer: Ever Bright Technology and Science

Electronical Co.,LTD Laser output: Less than 0.3 mW Wavelength: 790±25nm Standard: IEC60825-1: 2007

TASCAM CD-200iL

Pb, Hg, Cd

For European Customers

Safety Information

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

(b) By disposing of the electrical and electronic

equipment correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

serious effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.

(d) The crossed out wheeled dust bin symbol indicates

that electrical and electronic equipment must be collected and disposed of separately from household waste.

(e) The return and collection systems are available to

the end users. For more detailed information about disposal of old electrical and electronic equipment, please contact your city office, waste disposal service or the shop where you purchased the equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be

disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

(b) By disposing of waste batteries and/or accumulators

correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

lators can have serious effects on the environment and human health as a result of the presence of hazardous substances in batteries and/or accumulators.

(d) The crossed out wheeled dust bin symbol indicates

that batteries and/or accumulators must be collected and disposed of separately from household waste.

If the battery or accumulator contains more than

the specified values of lead (Pb), mercury (Hg), and/ or cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will be indicated beneath the crossed out wheeled dust bin symbol.

(e) The return and collection systems are available to

the end users. For more detailed information about disposal of waste batteries and/or accumulators, please contact your city office, waste disposal service or the shop where you purchased them.

For China

“仅适用于海拔2000m以下地区安全使用”

“仅适用于非熱帯气候条件下安全使用”

产品有毒有害物质或元素的名称及含量

机种：CD-200iL 有毒有害物质或元素

品名

1 CHASSIS部份 ○ ○ ○ ○ ○ ○ 2 FRONT PANEL部份 ○ ○ ○ ○ ○ ○ 3 螺丝部份 ○ ○ ○ ○ ○ ○ 4 线材部份 ○ ○ ○ ○ ○ ○ 5 PCB Assy部份 × ○ ○ ○ ○ ○ 6 CD MECH部份 ○ ○ ○ ○ ○ ○ 7 电源部份 ○ ○ ○ ○ ○ ○ 8 附属品部份 × ○ ○ ○ ○ ○ 9 LABEL部份 ○ ○ ○ ○ ○ ○

10 包装部份 ○ ○ ○ ○ ○ ○

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

○：表示该有毒有害物质在该部件所有均质材料中的含有量均在 SJ/T11363-2006 标准规定的限量要求以下。 ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。（针对现在代替技术困难的电子部品及合金中的铅 )

TASCAM CD-200iL

Contents

1 – Introduction ..............................................7

Features .................................................................................. 7

Included items .....................................................................7

Conventions used in this manual ..................................7

Trademarks ............................................................................ 7

Precautions for placement ..............................................8

Power supply ........................................................................ 8

Beware of condensation ...................................................8

Cleaning the unit ................................................................. 8

About discs ............................................................................ 8

Handling of compact discs ....................................... 8

User registration .................................................................. 8

2 – Names and functions of parts .................. 9

Front panel ............................................................................9

iPod dock ......................................................................10

Rear panel ............................................................................ 11

Display ...................................................................................11

Remote control unit (TASCAM RC-CD200iL) ...........12

3 – Preparations ............................................ 13

Making connections ........................................................13

Connecting an iPod or iPhone .....................................14

Opening the iPod dock ............................................ 14

Closing the iPod dock ...............................................15

Removing a dock adapter ..............................................16

Removing the iPod or iPhone ................................16

Connecting external audio players ............................ 16

Preparing the remote control ....................................... 17

Inserting batteries ......................................................17

Replacing the batteries ............................................ 17

Cautions about the use of batteries .................... 17

Cautions about using the remote control ......... 17

Loading a CD ......................................................................17

Selecting the output source (current source) .........18

Checking the program .............................................23

Replacing a program track .....................................24

Adding more program tracks ................................24

Clearing the program ............................................... 24

Repeat playback ................................................................24

Time and text information display .............................25

Pitch control playback ....................................................26

Intro check function ........................................................26

5 − iPod/iPhone Playback ............................27

iPod dock ............................................................................27

iPod/iPhone control .........................................................27

Preparing iPod/iPhone playback .................................27

6 – Message Lists ..........................................28

Operation messages ........................................................28

Warning messages ...........................................................28

Error messages ...................................................................28

7 – Troubleshooting .....................................29

8 – Specifications ..........................................30

Ratings ..................................................................................30

Input and output ratings ................................................30

Analog audio input ....................................................30

Analog audio output ratings..................................30

Digital audio output ratings ...................................30

Audio performance ..........................................................30

Backup memory ................................................................30

General .................................................................................30

Dimensions ......................................................................... 31

4 – CD playback .............................................19

Playable discs and files ................................................... 19

Folders and tracks on data CDs .................................. 19

Playback modes .................................................................20

Selecting the playback mode ................................ 20

Playback................................................................................20

Selecting a track ................................................................ 21

Skipping to the next or previous track ............... 21

Selecting by track number .....................................21

Search forward and backward ..................................... 21

Folder playback (data CDs) ............................................ 21

Setting the playback folder ....................................21

Programmed playback ....................................................22

Setting the program .................................................22

TASCAM CD-200iL

1 – Introduction

Thank you for your purchase of the TASCAM CD-200iL CD Player / iPod Dock.

Before connecting and using the unit, please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the unit, as well as the operation of its many useful and convenient functions. After you have finished reading this manual, please keep it in a safe place for future reference.

You can also download the Owner’s Manual from the TASCAM web sites (http://tascam.com/ or http://tascam.eu/ for Europe).

Features

•

In addition to audio CDs (CD-DA), this unit can also play data CDs (CD-ROM/R/RW) that contain files in WAV, MP3 and MP2 formats

•

2U rack mount size

•

Analog (RCA) and digital (coaxial and optical) outputs

•

Monitoring is possible with headphones

•

TASCAM RC-CD200iL wireless remote control with number (0–9) buttons included

•

Displays CD text and ID3 tag information (including artist, album and track names)

•

Three playback modes (continuous, shuffle and program)

•

Repeat (single and all) playback functions

•

CD playback pitch control function (±14%)

•

Intro check function

•

Data CD folder playback function

•

Time display possible (track elapsed time, track remaining time or total time for audio CDs or total elapsed time for data CDs)

•

CD drive has a 10-second shockproof memory that guards against skipping

•

Included dock for iPod/iPhone with Lightning and 30-pin dock connector enables iPod/iPhone control and audio output

•

Stereo mini jack for audio line input enables audio input from other portable audio devices

Included items

This product includes the following items. Take care when opening the package not to damage the items.

Keep the packing materials for transportation in the future. Please contact TASCAM if any of these items are missing or have

been damaged during transportation.

• Main unit ................................................................................................. 1

• Wireless remote control unit (RC-CD200iL) ................................ 1

• AA batteries ............................................................................................ 2

• A rack-mounting screw kit ................................................................ 1

• Warranty card ........................................................................................ 1

• Owner’s Manual (this manual) ......................................................... 1

Conventions used in this manual

In this manual, we use the following conventions:

•

Buttons, connectors and other parts of the unit and external devices are indicated like this: DISPLAY button

•

Text displayed on the display of the unit and external devices appears like this:

REPEAT

•

CD-DA format discs are sometimes called “audio CDs.”

•

CDs that contain audio files in MP2, MP3 or WAV formats are called “data CDs.”

•

MP3, MP2 and WAV files that can be played back by this unit are collectively called "audio files".

•

Audio CDs and data CDs are sometimes generically called “CDs”.

•

The currently selected folder is called the “current folder”.

•

Additional information is provided as necessary as tips, notes and cautions.

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and describe special cases.

CAUTION

Failure to follow these instructions could result in injury, damage to equipment or lost recording data, for example.

Trademarks

•

TASCAM is a trademark of TEAC CORPORATION, registered in the U.S. and other countries.

•

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

•

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

•

iPhone and iPod are trademarks of Apple Inc., registered in the U.S. and other countries.

•

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

Any data, including, but not limited to information, described herein are intended only as illustrations of such data and/or information and not as the specifications for such data and/ or information. TEAC Corporation disclaims any warranty that any use of such data and/or information shall be free from infringement of any third party’s intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such data and/or information.

This product is designed to help you record and reproduce sound works to which you own the copyright, or where you have obtained permission from the copyright holder or the rightful licensor. Unless you own the copyright, or have obtained the appropriate permission from the copyright holder or the rightful licensor, your unauthorized recording, reproduction or distribution thereof may result in severe criminal penalties under copyright laws and international copyright treaties. If you are uncertain about your rights, contact your legal advisor. Under no circumstances will TEAC Corporation be responsible for the consequences of any illegal copying performed using the recorder.

TASCAM CD-200iL

1 – Introduction

Precautions for placement

•

The operating temperature should be between 5°C and 35°C (41°F and 95°F).

•

Do not place the unit in the following types of locations. Doing so could degrade the sound quality or cause malfunction.

Places with frequent vibrations Near windows or in other places with direct exposure to

sunlight Near heating equipment and other extremely hot places Extremely cold places Very humid places and places with poor ventilation Very dusty places

•

Place the unit so that is level.

•

In order to assure good heat dispersion, do not place anything on top of the unit.

•

Avoid installing this unit on top of any heat-generating electrical device such as a power amplifier.

Power supply

Connect the unit to the standard power outlet. Hold the plug when connecting and disconnecting the power cord.

Beware of condensation

If the unit is moved from a cold to a warm place, or used immediately after a cold room has been heated or otherwise exposed to a sudden temperature change, condensation could occur. Should this happen, leave the unit for one or two hours before turning the unit on.

About discs

In addition to audio CDs (CD-DA), the CD-200iL can play CD-R and CD-RW discs on which audio CD, MP3, MP2 or WAV format files are recorded. The CD player can also play 3-inch CDs.

Handling of compact discs

•

Always place the compact discs in the trays with their label facing upward.

•

To remove a disc from its case, press down on the center of the disc holder, then lift the disc out, holding it carefully by the edges.

•

Do not touch the signal side (the unlabeled side). Fingerprints, oils and other substances can cause errors during playing.

•

To clean the signal side of a disc, wipe gently with a soft dry cloth from the center towards the outside edge. Dirt on discs can lower the sound quality, so clean them and always store them in a clean state.

•

Do not use any record spray, anti-static solutions, paint thinner or other chemical agents to clean CDs. This could damage the delicate playing surface and cause CDs to become unplayable.

•

Do not attach labels or anything else to discs. Do not use discs that have residue from, for example, tape or stickers that have been removed from the disc surface. Do not use discs that have exposed glue around the edges of stickers, for example. Loading such discs in the unit could cause them to become stuck or cause the unit to malfunction.

•

Never use commercially-available CD stabilizers. Their use could make playback impossible or cause the unit to malfunction.

•

Do not use cracked discs.

•

Only use circular compact discs. Do not use non-circular promotional, etc. discs.

Cleaning the unit

To clean the unit, wipe it gently with a soft dry cloth. Do not wipe with chemical cleaning cloths, paint thinner, ethyl alcohol or other chemical agents to clean the unit as they could damage the surface.

Once every five years, please contact the retailer where you purchased the unit or a TASCAM service center for internal cleaning. If the unit is not cleaned for a long time and dust is allowed to accumulate inside it, fire or malfunction could result. Cleaning is more effective when conducted before the humid season. Please check with us about the cost of internal cleaning.

•

Some record companies sell copy-protected discs or copy-controlled discs that may not play back correctly in this unit. Since such discs may not conform with the CD standard, do not use them in this unit.

•

If you experience problems with such non-standard discs, you should contact the producers of the disc.

User registration

Customers in the USA, please visit the TASCAM website (http:// tascam.com/) to register as a user online.

TASCAM CD-200iL

Front panel

2 – Names and functions of parts

1 POWER switch

Press this switch to turn the unit on or off.

CAUTION

Before turning the power on, minimize the volume of the connected device. Failure to do so could cause loud noises that might result in harm to your hearing or other trouble.

2 Disc tray

Press the OPEN/CLOSE button to open the disc tray and load/remove the disc.

Press the OPEN/CLOSE button to close the disc tray.

3 OPEN/CLOSE button

Use to open and close the disc tray.

4 PLAY/PAUSE button

Press during playback to pause. When playback is stopped or paused, press to start playback.

5 STOP button

When the current source is CD playback.

When in program setting mode, press this button when a track is selected to cancel the selection and return to the state where you can select a track again. (See “Setting the program” on page 22.)

Press this button when you can add a track to a new program step to clear the entire program. (See “Clearing the program” on page 24.)

-CD-,

press this button to stop

6 SEARCH m/,[.//] buttons

Press briefly to select tracks (skip). Press and hold to search a track.

7 PHONES jack and knob

Use this standard stereo jack to connect stereo headphones. Use a plug adapter when connecting headphones with mini-plugs.

Use the PHONES knob to adjust the headphone output level.

8 AUX IN jack

Use this stereo mini jack for line level audio input. Connect a portable digital audio player or other external

audio device to it.

CAUTION

Before connecting an external device to the AUX IN jack, minimize the volume of that device. Failure to do so could result in sudden loud noises that could, for example, harm your hearing.

9 DOCK FOR iPod

This iPod dock is compatible with Lightning connectors and 30-pin connectors. (See “Connecting an iPod or iPhone” on page 14.)

NOTE

When connecting an iPod or iPhone with a 30-pin connector, be sure to attach a dock adapter suitable for your iPod or iPhone to the 30-pin dock connector. Dock adapters are not included with this product. Use one that came with your iPod or iPhone or purchase an Apple Universal Dock Adapter made by Apple Inc.

0 Display

Displays various information.

q Remote Sensor

When operating the remote control unit (RC-CD200iL), point it towards here.

w DISPLAY [SHIFT] button

When the current source is change the time or text information shown on the display. (See “Time and text information display” on page 25.)

Press this button at the same time as another button to use that button's shift function, which is shown as white text with a dark background beneath the button.

-CD-

, press this button to

CAUTION

Use the PHONES knob to minimize the volume before connecting headphones. Failure to do so could cause a sudden burst of loud noise, which might result in hearing damage, for example.

TASCAM CD-200iL

2 – Names and functions of parts

CD DOCK AUXIN

e PLAY MODE/INTRO CHECK [SOURCE SEL] button

When the current source is change the playback mode. The three playback modes are continuous, shuffle and program. (See “Playback modes” on page 20.)

During playback or when stopped, press and hold this button to conduct intro check playback. During intro check playback, press and hold this button again to return to the ordinary playback mode. (See “Intro check function” on page

26.) When the current source is

change the iPod/iPhone shuffle playback mode. (See “iPod/iPhone control” on page 27.)

While pressing and holding the DISPLAY [SHIFT] button, press this button to change the current source in the following order.(See “Selecting the output source (current source)” on page 18.)

Current source order

-CD-

, press this button to

-DOCK-

, press this button to

NOTE

-DOCK-

sponding device is connected.

and

-AUX-

cannot be selected if no corre-

r REPEAT [PITCH ON/OFF] button

When the current source is the repeat playback function on/off and select the repeat playback mode. (See “Repeat playback” on page 24.)

While pressing and holding the DISPLAY [SHIFT] button, press this button to turn the pitch control function on/off. (See “Pitch control playback” on page 26.)

When the current source is to change the repeat playback mode. (See “iPod/iPhone control” on page 27.)

-CD-

, press this button to turn

-DOCK-

, press this button

t FOLDER g/t [PITCH −/+] buttons

When the current source is use these buttons to change the folder that will be played back. (See “Folder playback (data CDs)” on page 21.)

While pressing and holding the DISPLAY [SHIFT] button, use these buttons to set the CD pitch control value. (See “Pitch control playback” on page 26.)

When the current source is to skip among the albums on the iPod or iPhone (select albums). (See “iPod/iPhone control” on page 27.)

-CD-

and a data CD is loaded,

-DOCK-

, use these buttons

iPod dock

y 30-pin dock connector

Use this connector to connect an iPod or iPhone that uses a 30-pin dock connector.

NOTE

u Lightning connector

Use this connector to connect an iPod or iPhone that uses a Lightning connector.

i Backstop

Raise this backstop before connecting an iPod or iPhone that uses a Lightning connector.

o Unlocking lever

Use this lever to unlock the iPod dock in order to store it. To store the iPod dock, pull this lever while pressing the

dock toward the front of the unit.

TASCAM CD-200iL

+ 22 hidden pages