User’s Manual
52” Dual Color TFT LCD Monitor
Model Name : FS-S5202C
Model Number : 0100400003AA
Customer Project name : Aquarius Dual
TANDBERG Page 1 of
Item number : Item name :
117336
TANDBERG Monitor Dual 52” Assembly Rev.:01-draft
Date Sign Changes : Rev 01
Init
Tech
App
First build of the specification
Vendor Vendor/Manufacturer Part No FS-S5202C 0100400003AA
Vendor/Manufacturer must guarantee that assembly is in compliance with RoHS directive(tick-off)
All contents are confidential
Do not copy
General Specification
INFORMATION TO USER :
Document No. D&TQP0302-11(0) Revision No. 01 Page 2 of 22
1. General Description and Scope
2.1 General Description
This specification applies to the Type 52” Color TFT/LCD Module “LTI520HB01”. This module is
designed for a LCD TV style display unit. The screen format and electrical interface are intended to
support the VESA WUXGA (1920(H) ×1080(V) at 60Hz) screen. Supported Color is native 16.7M
colors (RGB-8bit data driver).
All input signals are LVDS (Low Voltage Differential Signaling) interface compatible.
2. Environmental and Reliability Specifications
3.1 Operating Conditions
3.1.1 Temperature : 0℃~ 40℃
Note : Max. Operating Temperature 40℃ in the spec means the temperature measured at the
point of the front surface of the LCD glass cell.
3.1.2 Humidity : 10% ~ 90%, non-condensing
3.1.3 Altitude : maximum 4,500m
3.1.4 Test
Type Parameters Description and comments Results
Low
temperature
T = 0°C
Dwell time = 8h + 2h (power-off)
Cold start-up after the power-off
period
Passed
High
temperature
T = +40°C
Dwell time = 8h + 2h (power-off)
Warm start-up after the power-off
period
Shield the unit against direct airflow
Passed
Low
pressure
P = 60kPa (4206m)
Pressure dwell time = 2h
T = +40°C
Shield the unit against direct airflow
Passed
0.5h
1h
2h
0.5h
Lab
amb
1h
3.5h 2.5h
0.1h
0.1h
0.5h
1h
8h
0.5h
Lab
amb
2h
1h
0.5h
1h
8h
0.5h
Lab
amb
0
2h
1h
Document No. D&TQP0302-11(0) Revision No. 01 Page 3 of 22
3.2 Non-Operational Conditions
3.2.1 Temperature : -20℃~ 60℃
3.2.2 Humidity : 10% ~ 90%, non-condensing
3.2.3 Altitude : maximum 15,000m
3.2.4 Test
Type Parameters Description and comments Results
Low
temperature
T = -20°C
Dwell time = 16h
Passed
High
temperature
T = +60°C
Dwell time = 16h
Passed
Thermal
shock
Low temperature = -20°C
High temperature = +60°C
Temperature gradient =
5°C/min
Dwell time = 2h
No. of cycles = 3
Passed
Humidity RH = 90%
Low temperature = 30°C
High temperature = 60°C
No. of cycles: 5 ea 24h
Passed
3h
9h
3h
9h
60
30
One cycle
Document No. D&TQP0302-11(0) Revision No. 01 Page 4 of 22
3.3 Packing Conditions
3.3.1 Temperature : -20℃~ 50℃
3.3.2 Humidity : 10% ~ 90%, non-condensing
3.3.3 Altitude : maximum15,000m
3.3.4 Test
Type Parameters Result
Drop surface Concrete or steel
Drop height Weight > 100kg: 0.1m
Impact area 6 faces
1 selected corner
1 selected edge
Freefall Drop
No. of drops 1 per impact area
Passed
Frequency range 5-10Hz 10-50Hz
Displacement 3.5mm
Acceleration 1g
Sweep rate 3min(5-50-5)
vibration
Duration Right/Left : 15min
Front/Back : 15min
Up/Down : 30min
Passed
Document No. D&TQP0302-11(0) Revision No. 01 Page 5 of 22
3. Input Signal and AC Power
4.1 AC Power
4.1.1 AC input voltage : AC 100 to 240 Volts (Universal power)
4.1.2 AC input frequency : 50~60Hz ±3Hz
4.2 Video and Sync Signal
4.2.1 Video signal
A. Horizontal frequency : 25 ~ 90KHz
B. Vertical frequency : 24 ~ 120Hz
C. Applicable maximum pixel frequency : 170MHz(Analog), 165MHz(Digital)
D. Maximum resolution : 1920x1200 / 60Hz
4.2.2 Signal connectors
A. HDMI type Ax3x2(Dual) : HDMI input
B. 15p D-Sub(Female, 3row) x1x2(Dual) : Analog RGB input
C. 9p D-Sub (Female) x1x2(Dual) : RS232C Input
D. 9p D-Sub (Male) x1x2(Dual) : RS232C Output
E. 15p D-Sub(Male, 2row) x1x(Dual) : Audio AMP signal input
F. AC Inlet x1x2(Dual) : main AC power input
4. Electrical Performance: Except where noted, the following test conditions are required.
5.1 Standard Testing Conditions
5.1.1 AC power voltage and frequency : AC 100 ~ 240V±10%, 60Hz/50Hz±3Hz
5.1.2 Ambient temperature: 25℃± 5℃
5.1.3 Brightness setting : set brightness control to the maximum level of the OSD
5.1.4 LCD panel direction : test at the parallel position with LCD panel center line
5.1.5 Ambient light level : between 300 lux and 700 lux
5.2 Power management
5.2.1 Power management
: This system can save energy by switching this monitor into a low-mode when the display video
signal is none. But power Management system can not be corresponded with VESA DPMS,
because of the TANDBERG’s operation specification.
5.2.1 Power Management Modes.
State Power consumption
Normal operation Max 1000Wrms
DPMS or Standby mode Max 50Wrms
Sleep mode Max 3.5Wrms
Document No. D&TQP0302-11(0) Revision No. 01 Page 6 of 22
5.3 LCD (Liquid Crystal Display) Panel Specifications
This specification applies to the Type 52” Color TFT/LCD Module “LTI520HB01”. This module is
designed for a LCD TV style display unit.
The screen format and electrical interface are intended to support the WUXGA(1920(H) ×1080(V))
screen. Supported gray scales are native 8bit per 1(one) sub pixel. All input signals are LVDS(Low
Voltage Differential Signaling) interface compatible.
5.3.1 General specification
Item SPECIFICATION UNIT NOTE
diagonal 1321 mm Display
area
viewable 1152.0(H) × 648.0(V) mm
Driver element a-Si TFT Active matrix
Number of Pixels 1920x1080, 2.07Million pixels
Pixel Pitch 0.6(H) ×0.6(V) mm
Pixel arrangement R. B, G Vertical Stripe
Display colors 16.7M (RGB 8-bit data)
Viewing angle(max) 178(H), 178(V) degrees 120 minutes after lighting on
Display mode Normally black
5.3.2 Optical characteristics (LCD panel specification)
The following optical characteristics are measured under stable conditions. It takes about
120minutes to reach stable conditions. The measuring point is the center of display area
unless otherwise noted.
The optical characteristics should be measured in a dark room or equivalent state.
Measuring equipment : TOPCON BM-7, SPECTRORADIOMETER SR-3
Temperature of LCD surface=25℃, VDD=12.0V, fV=60Hz, BRT=High(PWM Duty 100%)
ITEM SYMBOL CONDITION Min. Typ. Max. UNIT
Contrast Ratio C/R 1300 1700 - -
Rise Tr - 14 24 ms
Response
Time
Fall Tf - 8 10 ms
Brightness of white Bwh 500 600 - cd/m²
x 0.645
Red
y 0.336
x 0.275
Green
y 0.606
x 0.143
Blue
y 0.067
x 0.280
Color
Chromaticity
(CIE)
White
y
θ=0°
1)
TYP
-0.03
0.290
TYP
+0.03
-
θL 75 89 -
Hor
θR 75 89 -
θU 75 89 -
Viewing
Angle
Ver
θD
75 89 -
Degree
Loading...