The model and serial numbers of this unit may be found on the cabinet.
You should record and retain those numbers for future reference.
Model No.:
Serial No.:
Precautions5
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear or bottom of the cabinet.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
apparatus’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the apparatus.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the apparatus is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the apparatus and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug this apparatus from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: An apparatus that is meant for uninterrupted service
and, that for some speci c reason, such as the possibility of the
loss of an authorization code for a CAT V converter, is not intended
to be unplugged by the user for cleaning or any other purpose,
may exclude the reference to unplugging the apparatus in the
cleaning description otherwise required in item 5.
6.ATTACHMENTS - Do not use attachments not recommended by
the apparatus manufacturer as they may cause hazards.
7.WATER AND MOISTURE - Do not use this apparatus near water,
for example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this apparatus
on an unstable cart, stand, tripod, bracket, or
table. The apparatus may fall, causing serious
injury to someone, and serious damage to
the apparatus. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the apparatus.
Any mounting of the apparatus should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
An apparatus and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
apparatus and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé que sur un meuble
(avec ou sans roulettes) recommandé par le fabricant. Si vous l’
installez sur un meuble à roulettes, déplacez les deux ensembles
avec précaution. Un arrêt brusque, l’utilisation d’une force
excessive et des surfaces irrégulières risquent de déstabiliser l’
ensemble et de le renverser.
9. VENTILATION - Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the apparatus and to protect it from overheating,
these openings must not be blocked or covered. The openings
should never be blocked by placing the apparatus on a bed, sofa,
carpet, rug, or other similar surface. This apparatus should never
be placed near or over a radiator or heat register. This apparatus
should not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
2
EN
10. POWER SOURCES - This apparatus should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your apparatus dealer or local power company. For apparatuses
intended to operate from battery power, or other sources, refer to
the operating instructions.
11.GROUNDING OR POLARIZATION - This apparatus is equipped
with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will t into the power outlet
only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should
still fail to t, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12.POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the apparatus.
13.OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the apparatus, be sure the antenna or
cable system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
14. LIGHTNING - For added protection for this apparatus during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
apparatus due to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16.OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of re or electric shock.
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
INTRODUCTION
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this apparatus through openings as they may touch dangerous
voltage points or short out parts that could result in a re or electric
shock. Never spill liquid of any kind on the apparatus.
18. SERVICING - Do not attempt to service this apparatus yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to quali ed service personnel.
19.DAMAGE REQUIRING SERVICE - Unplug this apparatus from the
wall outlet and refer servicing to quali ed service personnel under
the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the apparatus.
c. If the apparatus has been exposed to rain or water.
d. If the apparatus does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjustment
of other controls may result in damage and will often require
extensive work by a quali ed technician to restore the apparatus
to its normal operation.
e. If the apparatus has been dropped or damaged in any way.
f. When the apparatus exhibits a distinct change in performance,
this indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts speci ed by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in re, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
apparatus, ask the service technician to perform routine safety
checks to determine that the apparatus is in proper operating
condition.
22. HEAT - This apparatus product should be situated away from heat
sources such as radiators, heat registers, stoves, or other products
(including ampli ers) that produce heat.
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne
FCC WARNING
RADIO-TV INTERFERENCE
This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this apparatus does cause harmful interference to radio or television reception, which can be
determined by turning the apparatus off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the apparatus and receiver.
3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
correspondante de la prise et pousser jusqu’au fond.
This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may
cause harmful interference unless the modifications are expressly approved in the manual. The user could
lose the authority to operate this apparatus if an unauthorized change or modification is made.
PREPARATION
INITIAL SETTING
WATCHING TVINFORMATION
OPTIONAL SETTINGTROUBLESHOOTING
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
LOCATION AND HANDLING
• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.
• Avoid a place with drastic temperature changes.
• Install the unit in a horizontal position. Do not place anything directly on top or bottom of the unit. Depending on your external devices,
noise or disturbance of the picture and/or sound may be generated if the unit is placed too close to them. In this case, please ensure
enough space between the external devices and the unit
• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• Do not put your fingers or objects into the unit.
NOTE ABOUT RECYCLING
• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with
your local recycling regulations.
• Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations
concerning chemical wastes.
EN
3
NTRODUCTION
I
Supplied Accessories5
owner’s manual
(1EMN22419A)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
Attaching the Stand
5
You must attach the stand to the unit to display upright. Be sure the front and rear of the stand match the proper direction.
remote control
(NF604UD)
batteries
(AA x 2)
Phillips pan screw for
attaching the stand x 2
(FPH34140)
Turn the main unit over and place
1
it onto a table which has a soft
cloth draped over it. Make sure
not to damage the screen.
Note:
• When attaching the stand, ensure that all screws are tightly fastened. If the stand is not properly attached, it could cause the unit to fall,
resulting in injuries as well as damage to the unit.
• Make sure to use a table which can support the weight of this unit and is larger than this unit.
• Make sure the table is in a stable location.
Symbols Used in this Manual
5
The following is the description for the symbols used
in this manual. Description refers to:
: Digital TV operation
DTV
: Analog TV operation
TV
• If neither symbol appears under the function
heading, operation is applicable to both.
Insert the stand all the way to the
2
main unit slowly.
Make sure not to put the AC cord
between the stand and the unit.
Tilt Stand
5
You can adjust the stand to change the angle
of the TV (-3° to 8°).
Drive Phillips pan screws in the 2
3
threaded holes with a screwdriver
tightly.
-3°
8°
Trademark Information
5
Manufactured under license from Dolby Laboratories.
•
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Product that have earned ENERGY STAR® are designed
•
to protect the environment through superior energy
efficiency.
4
EN
INTRODUCTION
Features5
• DTV/TV/CATV
- You can use your remote control to select channels which
are broadcast in digital format and conventional analog
format. Also, cable subscribers can access their cable TV
channels.
• Information Display (DTV only)
- You can display the title, contents and other information
of the current DTV program on the TV screen.
• Auto Channel Scan
- This unit automatically scans and memorizes channels
available in your area, eliminating difficult setup
procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for closed
caption supported programming.
• MTS/SAP Tuner
- Audio can be selected from the remote control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal and
no operation for 15 minutes, the unit will turn itself off
automatically.
• Sleep Timer
- This feature will automatically turned off the power of the
unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• Stereo Sound Function
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets you tune
directly to any channel using the channel number buttons
on the remote control.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded
or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai.
Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without
the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express
written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing
contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the
trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall
aggressively enforce its intellectual property rights to the fullest extent of the law.
5
EN
NTRODUCTION
I
Buttons on the Remote Control5
10
1. POWER (p11)
Press to turn the unit on and off.
1
2
3
4
5
6
7
8
9
2. MUTE
11
Press to turn the sound on and off.
3. SLEEP (p14)
12
13
Press to activate the sleep timer.
4. Number buttons (p13)
14
• Press to select channels.
-/ENT.
• Press to shift the minor channel
15
+100
• Press to select 100 or higher
• Press to search if there are minor
5. CH. K / L (p13)
Press to select channels and the
external input modes.
6. VOL. X / Y (p13)
Press to adjust the volume.
7. ENTER (p11)
Press to decide the command of
setting when the main menu is
displayed.
8. SETUP (p11)
Press to display the main menu.
9. s / B / K / L (p11)Press to move left/ right/ up/
down through the items.
(p13)
from the major channel.
channels. (CATV)
channels on the currently selected
major channel. (DTV)
10. RETURN
Press to return to previous menu
operation.
11. INPUT (p13)
• Press to access connected
external devices like a DVD player
or VCR.
• Press to switch between the
digital mode (DTV) and analog
mode.
12. DISPLAY (p15)
Digital Mode (DTV)
• Press to display the channel
information, signal type and TV
setting.
Analog Mode (TV)
• Press to display the channel
number, signal type and TV
setting.
External Input Mode
• Press to display the external
input modes, signal type and TV
setting.
13. AUDIO (p14)
Digital Mode (DTV)
• Press to select the audio
language.
Analog Mode (TV)
• Press to select the audio mode.
14. SCREEN MODE (p16)
Press to select aspect ratio
available for the TV screen.
15. CH. RECALL
Press to return to previous channel.
(p13)
Installing the Batteries
5
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
213
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
6
EN
INTRODUCTION
Control Panel5
1. POWER (p11)
POWER
INPUT SELECT
CHANNEL
1
2. INPUT SELECT (p13)
Press to access connected external devices like a
2
•
DVD player or VCR.
Press to turn the unit on and off.
3
Press to decide the command of setting when the
•
PREPARATION
menu is displayed.
VOLUME
4
SETUP
side of the unit
3. CHANNEL K / L (p13)
5
Press to select channels or move up/down through the
main menu items.
4. VOLUME X / Y (p13)
6
7
8
Press to adjust the volume or move right (X) / left (Y)
through the main menu items.
5. SETUP (p11)
INITIAL SETTING
Press to display the main menu.
6. infrared sensor window
WATCHING TVINFORMATION
Receives infrared rays transmitted from the remote
control.
7. power on indicator
Lights up when power is on.
8. standby indicator
Lights up in standby mode.
OPTIONAL SETTINGTROUBLESHOOTING
Rear Panel5
rear of this unit
COAXIAL
PrPbY
VIDEOS-VIDEO
VIDEO 2
VIDEO 1
AUDIOCOMPONENT
LR
AUDIO
LR
side of the unit
side of the unit
1. PC input jack (p10)
1
VGA cable connection for PC.
2. audio input jack for PC connection (p10)
Mini-plug audio cable connection for PC.
2
3. antenna input jack (p8)
RF coaxial cable connection for your antenna or
cable /satellite box.
4. headphone jack
Headphone connection for personal listening.
5. component video and audio input jack (p9)
Component video and RCA audio connection for
external devices.
6. audio input jack (p9)
RCA audio connection for external devices.
3
7. video input jack (p10)
RCA video connection for external devices.
8. S-video input jack (p9)
S-video connection for external devices.
4
9. coaxial digital audio output jack (p10)
Coaxial digital audio connection for a decoder or an
5
6
7
8
9
10
audio receiver.
10. AC power cord
Connect to a standard AC outlet to supply power to
this unit.
EN
7
REPARATION
P
Cables not included.
Please purchase the necessary cables at your local store.
Basic Connection
5
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Connection]
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF
antenna
RF coaxial cable
or
cable TV
company
rear of this unit
Once connections are completed, turn on the unit and begin initial setup.
*
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 11.)
Note:
• For your safety and to avoid damage to this unit, please unplug the RF coaxial cable from the antenna input jack before moving the
unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than
settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Use an RF coaxial cable to connect the antenna input jack of the unit to the antenna output jack of the cable/satellite box.
e.g.)
satellite dish
rear of this unit
cable TV
company
ANT OUTANT IN
or
RF coaxial cable
STEREO
PCM
cable/satellite box
RF coaxial cable
* Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
8
EN
(red)
(blue)
(green)
Cables not included.
Please purchase the necessary cables at your local store.
External Device Connection
5
[Component Video Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s component video input jacks, connect an RCA audio cable to the audio L/R jacks of
VIDEO2.
e.g.)
component video cable
PREPARATION
INITIAL SETTING
(red)(blue)(green)
rear of this unit
Pb/CbPr/CrY
TITLE 5
CHAPTER 15
REPEAT A-B
DVD player with
the component video jacks
COMPONENT VIDEO OUT
AUDIO OUT
RL
(green)
COAXIAL
(blue)
(red)(blue)(green)
(red)
PrPbY
VIDEOS-VIDEO
VIDEO 2
VIDEO 1
AUDIOCOMPONENT
LR
AUDIO
LR
RCA audio cable
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals.
[S-video Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s S-video input jack, connect an RCA audio cable to the audio L/R jacks of VIDEO1.
e.g.)
rear of this unit
S-VIDEO
OUT
RL
TITLE 5
CHAPTER 15
REPEAT A-B
AUDIO OUT
WATCHING TVINTRODUCTION
OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
DVD player with
the S-video output jack
COAXIAL
VIDEO 2
PrPbY
VIDEO 1
VIDEOS-VIDEO
AUDIOCOMPONENT
LR
AUDIO
LR
S-video cable
RCA audio cable
Note:
• If you connect to the S-video input jack and the video input jack at the same time, the S-video connection will have priority.
9
EN
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.