Sunbeam 4182 User Manual

User

Manual

10 SPEED BLENDER

Model 4182 4183 4184

safety

When using electrical appliances, basic safety precautions
should always be followed, including the following:

• READ ALL INSTRUCTIONS. KEEP THESE
INSTRUCTIONS FOR FUTURE USE.

• Verify that the voltage in your home corresponds to
that of your appliance.

• To protect against risk of electrical shock, do not put
cord, plug, base, or motor in water or other liquid.

• Close supervision is necessary when any appliance is
used by or near children.

• Unplug cord from outlet when not in use, before
putting on or taking off parts and before cleaning.

• Avoid contact with moving parts.

• Do not operate any electrical appliance with a
damaged cord or plug or after the appliance
malfunctions or has been dropped or damaged in any
manner. Return appliance to nearest Sunbeam
Appliance Authorized Service Center for examination,
electrical repair, mechanical repair, or adjustment.

• The use of attachments, including canning jars, not
recommended by the manufacturer may cause a risk
of injury to persons.

• Do not use outdoors.

• Do not let cord hang over the edge of a table or
counter or touch hot surfaces, including the stove.

• Keep hands and utensils out of container while
blending to reduce the risk of severe personal injury
and/or damage to blender. A rubber spatula may be
used but must be used only when blender is not
running.

IMPORTANT SAFEGUARDS

ii

• Do not use a broken, chipped or cracked blender jar.

• Do not use broken, cracked or loose cutting blades.

• To reduce the risk of injury, never place cutting unit
blades on base without jar properly attached. Blades
are sharp, handle with care.

• Always operate blender with cover in place.

• When blending hot liquids, remove center piece of
two-piece cover. Do not fill blender container beyond
3-cup level. Always begin processing at the lowest
speed setting. Keep hands and other exposed skin
away from the cover opening to prevent possible
burns. Jar will become hot from hot contents.

• Screw on blade assembly firmly. Injury can result if
moving blades accidentally become exposed.

• If the jar should turn when the motor is switched ON,
switch OFF immediately and tighten blade assembly.

• Do not leave blender unattended while it is operating.

• To disconnect cord, turn the control to OFF, then
remove the plug from wall outlet.

• Do not use appliance for other than intended purpose.

• THIS APPLIANCE INTENDED FOR HOUSEHOLD
USE ONLY. Use for food or liquids only.

• This appliance is equipped with a polarized plug. This
type of plug has one blade is wider than the other.
This plug will fit in a polarized outlet only one way.
This is a safety feature intended to help reduce the
risk of electrical shock. If you are unable to insert the

safety

SPECIAL INSTRUCTIONS

iii

plug into the outlet, reverse the plug. If it the plug
should still fail to fit, contact a qualified electrician to
replace the obsolete outlet. Do not attempt to defeat
this safety purpose of the polarized plug by modifying
the plug in any way.

• The length of the cord used on this appliance was
selected to reduce the hazards of becoming tangled in,
or tripping over a long cord. If a longer cord is
necessary an approved extension cord may be used.
The electrical rating of the extension cord must be
equal to or greater than the electrical rating of the
blender (3.4 ampere). Care must be taken to arrange
the extension cord so that it will not drape over the
countertop or tabletop where it can be pulled on by
children or accidentally tripped over.

• If the blender blades lock and do not move, it will
damage the motor. Do not use. Call the toll-free
customer service number for information.

• Do not place blender in the freezer filled with food or
liquid. This will freeze and damage the blade
assembly, jar and motor.

SAVE THESE

INSTRUCTIONS

safety

iv

contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Learning About 10-Speed Blender . . . . . . . . . . . . . . . . . 2

How to Assemble and Use . . . . . . . . . . . . . . . . . . . 3

Using the Blenders Special Features. . . . . . . . . . . . . . . 5

10-Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

For Continuous Operation . . . . . . . . . . . . . . . . . . . . 5

For Controlled Cycle Operation . . . . . . . . . . . . . . . . 5

Pulse Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Hints for Best Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Maintaining Your 10-Speed Blender . . . . . . . . . . . . . . . 7

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

One-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . 8

How to Obtain Warranty Service . . . . . . . . . . . . . . 8

Table of Contents

v

Welcome

Congratulations on your purchase of a SUNBEAM
Blender!

the utmost in quality, ease of use and convenience. Sunbeam
offers you an blender to fit your lifestyle:

Date product received:

Service number:
(Located on the bottom of the blender)

Sunbeam has designed your blender to provide

welcome

®

1

your blender

1. Filler-Cap (also used to tighten or loosen
blade assembly)

2. Lid

3. Jar (48 ounce)

4. Gasket

5. Blade Assembly (also called cutting blades)

6. Base

7. Control Panel

8. Off/Pulse Button

Learning About Your 10 SPEED BLENDER

2

O

ff

High

G

rate

Blend

G

rind

Liquefy

Ice

Crush

Pulse

Low

Stir

Puree

Chop

W

hip

M

ix

Cups

6 • 48 oz.

5 • 40

4 • 32

3 • 24

2 • 16

1 • 8

1

2

3

4

5

6

7

8

your blender

After unpacking the blender, wash everything except
the blender base in warm, soapy water. Dry
thoroughly. Do not place in dishwasher. Wipe the
blender base with a damp cloth or sponge. Do not
immerse the base in water. Care should be taken
when handling the blades, as they are very sharp.

How to Assemble and Use

Important: Your blender jar and cutting blades are

subject to wear during normal use. Always inspect
cutting blades for broken, cracked or loose blades. If
jar or cutting blades are damaged, do not use. Call
our toll-free customer service number to obtain
replacement parts.

• Make sure blender is unplugged. Place blender
base on clean, dry surface to keep foreign
particles from being pulled up into motor during
operation.

• Make sure gasket is in place on outer rim of
blade assembly. The gasket must lie flat. Screw
the blade assembly counterclockwise into the jar
base firmly using the finger tabs on the bottom of
blade assembly.

• To easily assemble into the jar, tilt the blade
assembly slightly and enter with the serrated
blade that curves up. Move as needed to clear the
remaining blades. When seated properly, turn the
blade assembly counterclockwise to tighten. To
remove, just reverse the process; turn the blade
assembly clockwise and lower slightly and in the
direction of the serrated blade tilt up and the
other blades will clear the jar bottom opening.

FIGURE 1

• NOTE: The blade assembly will turn counter

clockwise to tighten and clockwise to loosen.

• The transparent filler-cap is designed to assist in
tightening and loosening the blade assembly if
necessary.

FIGURE 2

• Remove the filler-cap from its position in the jar
lid and note the notches in the bottom (open)
end. These notches or slots engage the ribs on the

Your Blender

3

FIGURE 1

F

IGURE 2

FIGURE 3

C

u

ps

6

• 48 oz.

5

• 40

4

• 32

3

• 24

2

1 • 8

O
ff

H
i

g
h

G
r

a
t

e

B

le
n

d

P
u

lse

L
o

w

S
ti
r

P

u
r
e

e

C
h

• 16

G
r

in
d

Ic

e
L
iq

u
e

fy

C
ru

s

h

o
p

W

h

ip

M

ix

C

u

p

s

.

6

z

•

O

4

8