Studer Xcom-232i User Manual

Studer Innotec SA 2017 – V 1.3.0

4O9D

Communication module Xcom-232i

User Manual

Studer Innotec SA

Xcom-232i

2 V 1.3.0 User manual

COMMUNICATION MODULE XCOM-232I: USER MANUAL

V 1.3.0

Copyright © 2017 Studer Innotec SA

ABOUT THE SOFTWARE

This document applies to software versions V1.4.2 or higher of the Xcom-232i. It is possible to check
the currently used software version with the menu "Information on the system" or to update the
product with the latest software version available on "www.studer-innotec.com/en/downloads/".

LEGAL NOTICE

The use of Studer Innotec SA devices is the responsibility of the customer in all cases. Studer Innotec
SA reserves the right to make any modification to the product without prior notice.

PRODUCT RECYCLING

The Xcom-232i conforms to the European directive 2011/65/EU
on hazardous substances and does not contain the following
elements: lead, cadmium, mercury, hexavalent chrome, PBB or
PBDE.

To dispose of this product, please use the service for collection
of electrical waste and observe all applicable obligations according to the place of purchase.

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 3

TABLE OF CONTENTS

1 INTRODUCTION .................................................................................................................................... 4

1.1 The communication module Xcom-232i ....................................................................................... 4

1.2 Conventions ........................................................................................................................................ 4

1.2.1 Symbols .................................................................................................................................. 4

1.3 Warranty and liability ........................................................................................................................ 4

1.3.1 Disclaimer of warranty ......................................................................................................... 4

1.3.2 Disclaimer of liability ............................................................................................................. 5

1.3.3 Compatibility ......................................................................................................................... 5

1.4 Safety precautions ............................................................................................................................. 5

1.4.1 Generalities ........................................................................................................................... 5

1.4.2 Warnings ................................................................................................................................ 5

2 EU DECLARATION OF CONFORMITY .................................................................................................. 6

3 INSTALLATION ...................................................................................................................................... 7

3.1 Mounting ............................................................................................................................................. 8

3.1.1 Connecting the communication bus ................................................................................ 8

4 DESCRIPTION OF THE COMMUNICATION MODULE XCOM-232I ..................................................... 9

4.1 Front ...................................................................................................................................................... 9

4.2 Back .................................................................................................................................................... 11

4.3 MicroSD card .................................................................................................................................... 11

5 RS-232 COMMUNICATION ............................................................................................................... 12

6 DATA LOGGER ................................................................................................................................... 13

6.1 Functioning ........................................................................................................................................ 13

6.2 Analysis and visualization of the data with the Xtender data analysis tool or with the

Xtender Matlab® data analysis ............................................................................................................... 13

7 SOFTWARE UPDATING ....................................................................................................................... 14

7.1 Updating process ............................................................................................................................. 14

8 DIMENSIONS ...................................................................................................................................... 15

9 MOUNTING ........................................................................................................................................ 16

Studer Innotec SA

Xcom-232i

4 V 1.3.0 User manual

1 INTRODUCTION

1.1 THE COMMUNICATION MODULE XCOM-232I

Equipped with a serial port RS-232, the communication module Xcom-232i has been designed for
remote communication with any SCADA (Supervisory Control and Data) system. This module also
allows for data collection (energy consumption of a system, state of the auxiliary relays, input
currents and voltages, etc...) on a MicroSD card thanks to the function "Data logger".

1.2 CONVENTIONS

1.2.1 Symbols

This symbol is used to indicate the presence of a dangerous voltage that is sufficient

to constitute a risk of electric shock.

1.3 WARRANTY AND LIABILITY

During production and assembling, each Xcom-232i gets several controls and tests. They are
carried out in full respect of fixed procedures. Each Xcom-232i is given a serial number allowing a
perfect follow-up of the controls, in conformity with the specific data of every device. For this
reason, it is very important to never remove the descriptive sticker bearing the serial number. The
production, the assembling and the tests of each Xcom-232i are entirely carried out in our factory
in Sion (CH). The warranty of this product depends on the strict following of the instructions in this
manual. The warranty period for the Xcom-232i is 5 years.

1.3.1 Disclaimer of warranty

No warranty will be applied for damages caused by handling, operation or actions that are not
described in this manual. Damages arisen from the following events are not covered by the
warranty:

 Overvoltage on the device.
 Reverse polarity while connecting the battery.
 Liquid in the device or oxidation due to condensation.
 Failures due to a fall or to a mechanical shock.
 Modifications made without the explicit authorization of Studer Innotec SA .
 Nuts or screws partially or insufficiently tight during installation or maintenance.
 Damages due to atmospheric overvoltage (lightning).
 Damages due to transport or improper packaging.
 Disappearing of original marking items.

This symbol is used to indicate a risk of material damage.

This symbol is used to indicate information that is important or which serves to
optimize your system.

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 5

1.3.2 Disclaimer of liability

Installation, commissioning, use and maintenance of this device cannot be supervised by the
company Studer Innotec SA . For this reason, we do not accept any liability for damages, costs or
losses generated either by an installation that is not conforming to the prescriptions, by a defective
operation or by poor maintenance. The use of this device is under the responsibility of the end­user. This device is neither designed nor guaranteed for the supply of life support applications or
any other critical application with potential risks for human beings of for the environment. We shall
assume no liability for patent infringement or other third party rights involved in the use of this
device.

1.3.3 Compatibility

Studer Innotec SA guarantees the compatibility of the software updates with the hardware for
one year, starting from the date of purchase. The updates are no longer guaranteed beyond this
date and a hardware upgrade may be required. Please contact your reseller for any additional
information on compatibility.

1.4 SAFETY PRECAUTIONS

1.4.1 Generalities

Carefully read all safety instructions before proceeding with the installation and commissioning of
the device. Failure to follow these instructions might constitute a lethal physical danger but can
also damage the functionalities of the device. Therefore this manual should always be kept close
to the device.

For any installation, the local and national norms and regulations in force must be
strictly followed.

1.4.2 Warnings

 Wherever the installation, the person in charge of installation and commissioning must

perfectly know the safety measures and the prescriptions in force in the country. Therefore,
the whole maintenance must be carried out by a qualified staff.

 All components connected to this device must be conforming to the laws and regulations

in force. Persons without a written authorization from Studer Innotec SA are forbidden to
do any changes, modifications or repairs whatsoever. Regarding authorized modifications
and replacements, only genuine components shall be used.

 This device is meant for indoor use only and must under no circumstances be exposed to

rain, snow or any other humid or dusty environment.

 If used in motor vehicles, this device must also be protected against vibrations by

absorbing components.

Studer Innotec SA

Xcom-232i

6 V 1.3.0 User manual

2 EU DECLARATION OF CONFORMITY

The communication module Xcom-232i described in this manual meets the requirements specified
in the following EU directives and norms:

Low Voltage Directive (LVD) 2014/35/EU

- EN 62368-1:2014

Electromagnetic Compliance (EMC) Directive 2014/30/EU

- EN 61000-6-2:2005

- EN 61000-6-4:2007/A1:2011

CH - 1950 Sion, November 2016

Studer Innotec SA (R. Studer)

Studer Innotec SA contact details

Studer Innotec SA
Rue des Casernes 57
CH - 1950 Sion
Schweiz

[phone]
[phone]

[e-mail]
www.studer-innotec.com