Stryker REF 6203 User manual
2008/03 6203-001-700 Rev-B www.stryker.com
Instructions For Use
REF 6203
System 6
Single Trigger Rotary Handpiece
2 www.stryker.com
2008/03 6203-001-700 Rev-B
Intended Use
The Stryker System 6 Battery Powered Heavy Duty
Single Trigger Rotary Handpiece, when used with a variety of attachments, is intended for surgical procedures
involving drilling, reaming, driving wire or pins, cutting
bone and hard tissue.
Accessory Information*
DESCRIPTION REF
Small Battery Pack ................................................... 6212
Large Battery Pack .................................................. 6215
Aseptic Battery Kit ..................................................... 6126
Small Aseptic Battery Kit .......................................... 6127
*See the System 6 Rotary Handpiece Attachments
booklet for a complete list of attachments. Contact your
Stryker sales representative for a complete list of additional accessories.
WARNING: Use only Stryker-approved
components and accessories, unless otherwise specified. Other accessories may result in increased electromagnetic emissions
or decreased electromagnetic immunity of
the system. DO NOT modify any component
or accessory. Failure to comply may result
in patient and/or health care staff injury.
Important Information
The words WARNING, CAUTION and NOTE have special
meaning and should be reviewed.
WARNING:
Disregarding WARNING information
may compromise the safety of the
patient and/or health care staff and
may result in injury.
CAUTION:
Disregarding CAUTION information
may compromise product reliability
and may result in damage.
NOTE:
NOTE information supplements and/
or clarifies procedural information.
A triangle with an exclamation point
alerts the health care professional to
read and understand the accompanying instructions, especially the
operating, maintenance, and safety
information.
6203-001-700 Rev-B 2008/03
www.stryker.com 3
User/Patient Safety*
WARNINGS:
• Only trained and experienced health care professionals should use this equipment. Before using any
system component or any component compatible
with this system, read and understand the instructions. Pay special attention to WARNING information.
Become familiar with the system components prior
to use. Failure to comply may result in patient and/or
health care staff injury.
• Upon initial receipt and before each use, operate the
equipment and inspect each component for damage.
DO NOT use any component if damage is apparent.
Failure to comply may result in patient and/or health
care staff injury.
• Perform recommended periodic maintenance as
indicated in the instructions for use. Only trained
and experienced health care professionals should
maintain this equipment.
• Clean and sterilize handpieces, attachments and batteries before first and every use.
• DO NOT use this equipment in the presence of a
mixture consisting of flammable anesthetic and air or
with oxygen or nitrous oxide.
*If you need more information, contact your Stryker sales representative or call Stryker customer service at 1-800-253-3210. Outside
the US, contact your nearest Stryker subsidiary.
• Take special precautions regarding electromagnetic
compatibility (EMC) when using medical electrical equipment like the handpiece. Install and place
the handpiece into service according to the EMC
information in this manual. Portable and mobile RF
communications equipment can affect the function of
the handpiece.
• ALWAYS place the handpiece in the safe mode while
the handpiece is idle, before installing or removing
any accessory, or when passing the handpiece to another person. Failure to comply may result in patient
and/or health care staff injury.
• A wobbling attachment may cause bone or tissue
damage or inaccurate wiring or pin placement. If
wobbling occurs, see Troubleshooting Guide. Failure
to comply may result in patient injury.
• DO NOT apply excessive pressure, such as bending
or prying, with a cutting accessory to prevent fracturing the accessory. Applying excessive pressure,
especially during high operating speeds, may cause
the cutting accessory to bend significantly and result
in tissue damage, loss of tactile control and the ejection of cutting accessory pieces at a high velocity.
Failure to comply may result in patient and/or health
care staff injury.
• DO NOT reuse single use cutting accessories. Failure
to comply may result in patient and/or health care
staff injury.
4 www.stryker.com
2008/03 6203-001-700 Rev-B
Features
• Battery Latch - To release the battery pack from the handpiece, depress the battery latch.
• Battery Pack - Rechargeable battery pack provides power to the handpiece.
• Trigger Switch - To cause rotation and vary speed, press this pressure-sensitive trigger.
• F/R/Safe Control - Based on its position, allows the handpiece to operate in forward or reverse mode; safe mode
prevents the operation of the handpiece.
• Actuating Collar - To release the attachment, slide the actuating collar.
• Shifter Knob - To select the handpiece mode of REAM [slow] or DRILL [fast], rotate the knob to the appropriate
position, as required.
• Accessory Interface - Connector provides power and communication for future accessories.
Symbol Definitions
Battery Latch
Battery Pack
Trigger Switch
Actuating Collar
Shifter Knob
F/R/Safe Control
Accessory Interface
Slide the F/R/Safe
control to the
forward position
to allow the
handpiece to run
clockwise while
the trigger is
depressed.
Slide the F/R/Safe
control to the
safe position to
prevent inadvertent
operation of the
handpiece – the
handpiece cannot
be operated.
Slide the F/R/
Safe control to
the reverse position to allow the
handpiece to run
counterclockwise
while the trigger
is depressed.
For fast mode, rotate shifter knob to
DRILL
For slow mode, rotate shifter knob to
REAM
6203-001-700 Rev-B 2008/03
www.stryker.com 5
Slide the F/R/Safe control to the safe position.
To install an attachment, align the driveshaft of the
attachment with the handpiece spindle. If the attachment has notches, also align the notches with the
tabs in the sleeve of the handpiece (see figure 1).
1.
2.
Figure 2 To Install Battery Pack
Instructions
To Install Battery Pack
NOTES:
• This handpiece is designed to accept a Stryker Large
or Small Battery Pack only (REF 6215 or REF 6212).
These battery packs can be charged in the Stryker
System 6 Battery Charger REF 6110-120 configured
with the appropriate battery charger modules.
• See the instructions supplied with the battery charger
and/or battery pack for charging details and specifications.
Slide a fully charged battery pack firmly into the
handpiece until the battery latch snaps, indicating the
battery pack is secure (see figure 2).
1.
Once properly aligned, insert the attachment into the
handpiece until the attachment “snaps” into place.
Tug the attachment to ensure it is secure.
Install the desired cutting accessory. See the System
6 Rotary Handpiece Attachments booklet.
3.
4.
5.
NOTE: Several attachments are available and each
has a specialized accessory retainer.
WARNING: To prevent inadvertent run-
ning of the handpiece, ALWAYS place the
F/R/Safe control in the safe position before
installing or removing any attachment.
To Install Attachment
Test the operation of the handpiece by sliding the
F/R/Safe Control to FORWARD (F) or REVERSE (R)
and squeezing the trigger.
Slide the F/R/Safe control to the safe position until
you are ready to use the handpiece.
2.
3.
Figure 1 To Install Attachment
Driveshaft
Tabs
Notches
(not always
present)
Loading...