Spektrum DX5R Instruction Manual

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di istruzioni

DX5R

5-Channel 2.4GHz DSMR® System

2

Spektrum DX5r • tranSmitter inStruction manual

EN

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechani­cal ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use
with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS

Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby,
LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or
products claiming compatibility with DSM or Spektrum.

Age Recommendation: Not for Children under 14 years. This is not a toy.

WARRANTY REGISTRATION

Visit community.spektrumrc.com today to register your product.

SAFETY PRECAUTIONS

• Always ensure all batteries have been properly charged prior
to using the model.

• Always check all servos and their connections prior to each
run.

• Never operate your model near spectators, parking areas or
any other area that could result in injury to people or damage
of property.

• Never operate your model during adverse weather conditions.
Poor visibility can cause disorientation and loss of control of
your model.

• Never point the transmitter antenna directly toward the
model. The radiation pattern from the tip of the antenna is
inherently low.

• If at any time during the operation of your model you observe
any erratic or abnormal operation, immediately stop opera­tion of your model until the cause of the problem has been
ascertained and corrected.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For
up-to-date product literature, visit horizonhobby.com and click on the support tab for this Product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this
product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of
injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of seri­ous injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and serious
injury OR create a high probability of superficial injury.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby
disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

3

Spektrum DX5r • tranSmitter inStruction manual

EN

TABLE OF CONTENTS

IDENTIFYING CONTROLS AND SWITCHES

A

B

C

D

E

F

G

H

J

I

K

L

M

T

S

R

O

N

P
Q

A: Button C
B: Switch I
C: Knob
D: Button B
E: Button F
F: Button G
G: Button H
H: Button A
I: Button E
J: Trigger (throttle/brake)
K: Steering Wheel

L: Button D
M: Antenna
N: LCD Screen
O: Button L
P: Roller Wheel
Q: Button R
R: SD Card Reader
S: Power LED
T: Power Button

Installing Batteries ..............................................................4

Battery and Charging Precautions and Warnings ............... 4

SD Card ...............................................................................5

Main Screen........................................................................7

Navigation ...........................................................................7

Function List ....................................................................... 8

Model Select ......................................................................8

Model Name ....................................................................... 8

Servo Setup ........................................................................9

Rates ............................................................................... 10

Exponential .......................................................................10

Timer ............................................................................... 10

Binding/Frame rate ........................................................... 11

Bind the Transmitter to the Receiver ................................... 11

Failsafe ............................................................................ 11

Mixing .............................................................................. 12

Steer Mix ..........................................................................12

4WS (4-Wheel Steering) .................................................... 12

2 Servo (Dual Steering) .....................................................12

Dual throttle .....................................................................13

Dual Brake .......................................................................13

Motor on axel (MOA) .........................................................13

PROgrammable Mix .......................................................... 14

Active Vehicle Control (AVC) ............................................... 14

Automatic Braking System (Abs) ........................................ 15

Idle Up .............................................................................15

Traction ............................................................................ 16

Trim setup ........................................................................ 16

Channel Assign ................................................................. 16

Telemetry ......................................................................... 16

Drive Mode ....................................................................... 17

System settings ................................................................ 17

Display ............................................................................. 17

Trims................................................................................18

Sound settings ..................................................................18

About ............................................................................... 18

Calibrate ..........................................................................18

System setup .................................................................... 19

Model Select ....................................................................19

Model Utilities ................................................................... 19

System setup ....................................................................20

Create new model .............................................................20

Delete model .................................................................... 20

Copy model ...................................................................... 20

Reset model ..................................................................... 20

Sort model list ..................................................................20

System setup ....................................................................21

Transfer sd card ................................................................21

Import model .................................................................... 21

Export model .................................................................... 21

Update firmware ............................................................... 21

PHYSICAL TRANSMITTER ADJUSTMENTS ......................... 22

Changing grips ................................................................. 22

Dropdown steering wheel options ......................................23

Rotate: .............................................................................23

Standard wheel conversion: ............................................... 23

steering wheel wedges (not included) ................................. 23

Receiver Compatibility ...................................................... 24

Optional Parts List ............................................................24

1-Year Limited Warranty ...................................................25

Troubleshooting Guide ...................................................... 26

Warranty and Service Contact Information .......................26

FCC Information ................................................................ 27

IC Information ................................................................... 27

Compliance Information for the European Union .............. 27

4

Spektrum DX5r • tranSmitter inStruction manual

EN

INSTALLING BATTERIES

CHARGING AND WARNINGS

CHARGING THE OPTIONAL LITHIUM ION BATTERY PACK

CAUTION: NEVER remove the transmitter batteries

while the model is powered on. Loss of model control,
damage or injury may occur.

CAUTION: Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to
state and local laws.

Installing Optional Lithium Ion Battery Pack

IMPORTANT: Set the transmitter battery type to Li-Ion in the

Display/Battery menu and ensure the battery voltage alert is set
to the proper voltage. See the System section for more details.

Failure to exercise caution while using this product and comply
with the following warnings could result in product malfunction,
electrical issues, excessive heat, FIRE, and ultimately injury and
property damage.

• Read all safety precautions and literature prior to use of this
product

• Never allow minors to charge battery packs

• Never drop charger or batteries

• Never attempt to charge damaged batteries

• Never attempt to charge a battery pack containing different

types of batteries

• Never charge a battery if the cable has been pinched or
shorted

• Never allow batteries or battery packs to come into contact
with moisture at any time

• Never charge batteries in extremely hot or cold places

(recommended between 50–80˚ F or 10–27˚ C) or place in
direct sunlight

• Always disconnect the battery after charging, and let the

charger cool between charges

• Always inspect a new battery before charging

• Always terminate all processes and contact Horizon Hobby

if the product malfunctions

• Always keep batteries and charger away from any material

that could be affected by heat.

• Always end the charging process if the charger or battery

becomes hot to the touch or starts to change form (swell)
during the charge process

NOTICE: Only use the recomended power supply (SPM9551)
with the DX5R transmitter.

Always charge the transmitter on a heat-resistant surface.

1. Power off your transmitter.

2. Connect the power supply (SPM9551) connector to the

Li-Ion charge port located through the opening in the battery
door.

3. Connect the power supply to a power outlet using a country

specific adapter.

4. Disconnect the transmitter from the power supply once

charging is complete and disconnect the power supply from
the power outlet.

CAUTION: Never leave a charging battery unattended.

CAUTION: Never charge a battery overnight.

CAUTION: Never connect an external battery charger to

the transmitter.

1. Remove the battery cover from the bottm of the transmitter.

2. Remove the AA battery holder and disconnect from the

transmitter power port.

3. Connect the battery pack to the transmitter power port.

4. Install the battery pack into the transmitter.

5. Install the battery cover.

1. Remove the battery cover from the bottom of the transmitter.

2. Install 4 AA batteries as shown.

3. Install the battery cover.

5

Spektrum DX5r • tranSmitter inStruction manual

EN

Registering the Transmitter

MICRO SD-CARD*

Installing the Micro SD-Card

The Micro SD-Card (not included) enables you to:

• Import (copy) models from any compatible Spektrum™
RaceWare™ transmitter

• Export (transfer) models to any Spektrum RaceWare transmitter

• Update Firmware in the transmitter

To install the Micro SD-Card:

1. Power off the transmitter.

2. Install the Micro SD-Card in the card reader slot located

behind the small rubber door on the side of the transmitter.

*For more Micro SD-Card information see the Transfer SD Card section.

Exporting the transmitter serial number to the Micro SD­Card allows you to upload the serial number directly into the
registration screen at www.spektrumrc.com.

To export the serial number:

1. Install the Micro SD-Card in the card reader slot located

behind a small rubber door on the back of the transmitter

2. Click the scroll wheel to enter the FUNCTION LIST.

3. Scroll down to the System Settings

menu. Click the scroll wheel once to
open the menu.

4. Scroll to ABOUT and click the scroll

wheel once to open the menu.

5. When the Serial Number screen

appears, select EXPORT.

6. Power off the transmitter and remove

the Micro SD-Card from the transmitter.

To Upload the serial number to www.

spektrumrc.com:

1. Insert the Micro SD-Card in your computer and check the

contents of the SD card on your computer for a “My_DX5R.
xml” file.

2. In your favorite browser navigate to www.spektrumrc.com

and find the Product Registration link on the top of the
page as shown.

3. If you do not already have an account, create one now. If

you have an account, login in with your secure login.

4. Once logged in, go to the “My Spektrum” page. Fill out

all relevant information. Once you select your transmitter
model from the pull down menu you will be asked to
upload the serial number.

5. Click on the Select button to navigate to the “My_DX5R.

xml” file on the Micro SD-Card that is in your computer’s
SD card reader and select the file.

6. Click on the Upload from xml file... button and the serial

number will populate into the Serial Number fields.

7. Click Register at the bottom of the screen to finish

registering your new Spektrum Transmitter.

Alternatively, you can copy the serial number from the .xml
file and paste directly into the Serial Number field.

Screen shots from www.spektrumrc.com are correct at time of
printing but may change at a future date.

6

Spektrum DX5r • tranSmitter inStruction manual

EN

Update RaceWare™ Software

NOTICE: The orange LED Spektrum bars flash and a status bar

appears on the screen when RaceWare™ software updates
are installing. Never power off the transmitter when updates
are installing. Doing so may damage the system files.

NOTICE: Before installing any RaceWare files, always Export All
Models to an SD Card separate from the SD Card containing
the update. The update may erase all model files.

For more information on RaceWare software updates, visit

www.spektrumrc.com
Automatically Installing RaceWare Software Updates

1. In your favorite browser navigate to www.spektrumrc.com

and find the Firmware Updates link inside the Setups/
Updates tab on the top of the page as shown.

2. Find your registered transmitter in the MY PRODUCTS list

and click on Download Updates. Follow directions on the
screen for downloading the update to your computer and
SD card.

3. Eject the Micro SD Card from the computer.

4. Make sure the transmitter is powered off and install the SD

card into the transmitter.

5. Power on the transmitter and the update automatically

installs in the transmitter.

Manually Installing RaceWare Software Updates

1. Save the desired RaceWare version to the SD Card.

2. Install the SD card into the transmitter.

3. Select Update Firmware in the SD Card Menu options. The

Select File screen appears.

4. Select the desired RaceWare version from the File List.

When updates are installing, the transmitter screen is
dark. The orange LED Spektrum bars flash and the update
status bar appears on the screen.

NOTICE: Do not power off the transmitter when updates are
installing. Doing so will damage the transmitter.

Screen shots from www.spektrumrc.com are correct at time of
printing but may change at a future date.

SD CARD

7

Spektrum DX5r • tranSmitter inStruction manual

EN

USING THE SCROLL WHEEL SELECTOR

• Scroll the scroll wheel to move through the screen content or
change programming values. Click the scroll wheel to make a
selection.

• Use the L Button to go back to go to the previous screen (for
example, to go from the Mixing Screen to the Function List).

• Use the R Button to return a selected value on a screen to the
default setting.

• The Main Screen appears when you power on the transmitter.
Click the scroll wheel once to display the Function List.

INDIVIDUAL DIRECTION ADJUSTMENTS

In some instances, you may find it necessary to independently adjust the control directions; for example, if you want more travel for
left steering than right steering, perform the following steps:

1. Scroll to the value you wish to change and click the scroll wheel.

2. When both directions are selected, move the control (steering or throttle) toward the control direction you wish to change. The

selection box moves to the desired direction. You do not need to hold the control in the desired direction.

3. To change the opposite direction, simply move the control in that direction.

4. Click the scroll wheel to save the selection.

The Main Screen displays information about the active model,
including the Timer (when activated). To return to the Main
Screen at any time, press and hold the scroll wheel for at least
6 seconds.

A: Transmitter Battery Voltage
B: User Name
C: Model Name
D: Steering Rate
E: Timer 1 (when activated)
F: Timer 2 (when activated)
G: Position of Steering (STR) trim
H: Position of Throttle (THR) trim
I: Position of Brake (BRK) trim
J: Position of Aux 1 trim
K: Position of Aux 2 trim
L: Position of Aux 3 trim

Turn

Press

Press

To Enter, Choose or
Exit a selection.

To move between
options or change
values in an option.

Hold for 6 seconds and
release to return to the
Main screen.

SCROLL HOLDCLICK

MAIN SCREEN

NAVIGATION

A

C

B

D

E

F
G
H

I
J
K
L

Tip: The tick mark below shows the

current switch position.
Rolling and clicking the scroll wheel turns

the selected box black, indicating that the
value or condition will act on that position.

AUTO SWITCH SELECT

To easily select a switch in a function, such as a program mix,
roll with the scroll wheel to highlight the switch selection box,
and click the scroll wheel. The box around the switch should now
flash. To select a switch, toggle the switch you wish to select.
Verify the switch selection is now displayed as desired. When
correct, click the scroll wheel to select this switch and complete
the switch selection.

8

Spektrum DX5r • tranSmitter inStruction manual

EN

MODEL SELECT

MODEL NAME

Model Select enables you to access any of the 250 internal model memory locations in the Model Select list.

1. Scroll to the desired model memory in the Model Select list.

2. When the desired model memory is highlighted, click the scroll wheel once to select the model. The

transmitter returns to the Main Screen.

3. Add a new model by rolling to the bottom of the list. You will then be prompted with the Create New

Model screen, with the option to create a new model or cancel. If you select Cancel, the system will
return to the Model Select function. If you select Create, the new model will be created and now be
available in the model select list.

CAUTION: NEVER change the model in Model Select while operating a model. Changing the model
memory interrupts the transmitter signal to the receiver and may cause loss of vehicle control,
damage or personal injury.

Model Name enables you to assign a custom name to the current model memory. Model names can include up
to 15 characters, including spaces.

To add letters to a Model Name:

1. Scroll to the desired letter position and click the scroll wheel once. A flashing box appears.

2. Scroll Up or Down until the desired character appears. Click the scroll wheel once to save the character.

3. Scroll to the next desired letter position. Repeat Steps 1 and 2 until the Model Name is complete.

4. Select L button to return to the FUNCTION LIST.
To erase a character(s):

1. Press the R button while the character is selected.

2. Press the R button a second time to erase all characters to the right of the cursor.

FUNCTION LIST

Click the scroll wheel from the main screen to access the FUNCTION LIST. The FUNCTION LIST contains all the available menus on the
DX5R. The functions include:

• Model Select

• Model Name

• Servo Setup

• Rates

• Exponential

• Timer

• Bind/ Frame Rate

• Mixing

• AVC

• ABS

• Idle Up

• Traction

• Trim Setup

• Channel Assign

• Telemetry

• Drive Mode Name

• System Settings

• System Setup

9

Spektrum DX5r • tranSmitter inStruction manual

EN

SERVO SETUP

The Servo Setup menu contains the following functions:

Travel Adjust

Travel Adjust sets the overall travel or endpoints of the servo arm movement. Travel values range from 0–150% (Default is 100%).

To adjust Travel values:

1. Scroll to the channel you wish to adjust and click the scroll wheel.

2. Scroll Up or Down to adjust the travel value. Click the scroll wheel to save the selection.

Sub-Trim

Subtrim offsets the entire stroke including the center and endpoint positions.

CAUTION Use only small sub-trim values or you may cause damage to the servo.

Reverse

Use the Reverse menu to reverse the channel direction. For example, if the Steering servo moves Left and it should move Right.

To reverse a channel direction:

1. Scroll to Travel and click the scroll wheel. Scroll up or down until Reverse appears and click the scroll wheel again to save the

selection.

2. Scroll to the channel you wish to reverse and click the scroll wheel.

If you reverse the Throttle channel, a confirmation screen appears. Select YES to reverse the channel. A second screen appears,
reminding you to bind your transmitter and receiver.

CAUTION: Always rebind the transmitter and receiver after reversing the Throttle channel. Failure to do so will result in the
throttle moving to full throttle if failsafe activates.

Always perform a control test after making adjustments to confirm the vehicle responds properly.

CAUTION: After adjusting servos, always rebind the transmitter and receiver to set the failsafe position.

Speed

The Speed menu enables you to slow the response time on any individual channel.
The Speed is adjustable from 100% to 1%.

To adjust the Speed:

1. Scroll to the channel you wish to adjust and click the scroll wheel.

2. Scroll Up or Down to adjust the speed and click the scroll wheel to save the selection.

3. Select a switch to activate/deactivate the function. If Switch ON is selected, the value will always be on for that function.

FUNCTION LIST

10

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

RATES

EXPONENTIAL

TIMER

Rates (dual rate) allow you to make on-the-fly travel adjustments to Steering, Throttle or Brakes using any of
the Programmable trimmers. The Rate screen also offers an override function, which allows you to access a
second rate (normally 100%) at the touch of a button or trimmer. This is especially helpful for oval racers that
program minimal steering throw to desensitize steering during racing, but requires maximum steering angle to
drive out of a crash or get turned around on the track.

To adjust Rate values:

1. Scroll to Steering and click the scroll wheel to select between Steering, Throttle or Brake. Click the wheel

to save the selection.

2. Scroll Up or Down to adjust the Rate value. Click the scroll wheel to save the selection.

3. Select a Rate switch.

4. Select an Override rate and switch.

5. Select the OTF trimmer that will be used to adjust Rates on the fly.

IMPORTANT: In order for the OVERRIDE to operate, you must assign it to a switch or trimmer. The default
position for this function is inhibited.

The Exponential (Expo) function affects the response rate of the steering, throttle and/or brake. A positive
Steering Expo value, for example, decreases steering sensitivity around neutral to make it easier to drive at
high speeds in a straight line while still allowing for maximum turning radius. While sensitivity with positive
Expo is decreased around neutral, it increases the sensitivity near the end of travel.

To adjust Expo values:

1. Select Throttle or Steering.

2. Scroll Up or Down to adjust the Rate value. The graph shows the Expo Curve.

3. Click the scroll wheel to save the selection.

4. Select an OTF switch to activate Exponential.

If Switch ON is selected, the Expo value will always be on for that function. If another switch is selected, the
Expo can be turned ON/OFF or 2-3 different Expo values can be entered depending on the switch used.

IMPORTANT: Both positive and negative Expo values are available. A positive Expo value results in the
center being less sensitive (desirable most of the time), while a negative value increases the sensitivity
around center (normally not used).

The DX5R Timer function allows you to program a countdown timer and stop watch (count up timer) to display
on the main screen. An alarm sounds when the programmed time is reached. You can program the timer
to start using the assigned switch position or automatically when throttle moves above a pre programmed
position.

Two internal timers are available that show run time for a specific model displayed on the Main Screen. and a
total system timer.

11

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

BINDING/FRAME RATE

Binding is the Process of teaching the receiver the specific transmitter’s code called GUID (Globally Unique
Identifier) and storing failsafe values. When a receiver is bound to a transmitter/model memory, the receiver will
only respond to that specific transmitter/model memory.

BIND THE TRANSMITTER TO THE RECEIVER

1. Place the receiver into Bind mode, the LED on the receiver will begin to flash.

2. Power on the transmitter.

3. Select the Model Memory you wish to bind to.

4. Select Bind from the List menu.

5. Move the throttle channel to the desired failsafe position.
IMPORTANT: The throttle channel must stay in the failsafe position until binding is complete.

6. Scroll to Bind and click the scroll wheel. The orange LED flashes on top of the transmitter.

7. When the bind process is complete, the transmitter and receiver LEDs stop flashing and turn solid orange.

8. Remove the bind plug from the receiver and keep it in a convenient place.

NOTICE: Always remove the bind plug from the receiver when the bind Process is complete. Failure to do so

will cause the receiver to enter bind mode the next time you power on the receiver.

FAILSAFE

The throttle failsafe position is set during binding. In the unlikely event that the radio link is lost during use, the receiver will drive the
throttle servo to its pre-Programmed failsafe position (normally full brakes) and all other channels will have no servo output. If the
receiver is turned on prior to turning on the transmitter, the receiver will enter the failsafe mode, driving the throttle servo to its preset
failsafe position. When the transmitter is turned on, normal control is resumed.

IMPORTANT: Failsafe activates only in the event that signal is lost from the transmitter. Failsafe will NOT activate in the event that
receiver battery power decreases below the recommended minimums or power to the receiver is lost.

FRAME RATE:

For compatibility with all types of servos, four frame rates are available:

• 5.5ms: Gives the fastest response rate. Digital Servos and a compatible receiver are required.
IMPORTANT: When 5.5ms frame rate is selected, only two channels (steering and throttle) are operational.

• 11ms: Offers good response rates and is compatible with most digital and analog servos (this is the

default position). Works with DSMR surface receivers.

• 16.5ms: Needed for older analog servos. Works with DSM2

®

surface receivers.

• 22ms: Needed for older analog servos. Works with DSMR® receivers.
IMPORTANT: You should always use the fastest response rate the servos can handle. This gives the lowest

latency and fastest response. If the frame rate is incompatible with the servo, the servo will move erratically
or, in some cases, not at all. If this occurs, change the frame rate to the next highest value.

IMPORTANT: Always rebind after changing the Frame Rate.

12

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

MIXING

The DX5R features preset steering and throttle mixes and four programmable mixes. If AVC® technology is
active, only two channels, Steering and Throttle, are operational. The Aux channels can be used to power a
personal transponder, lights, etc.
If AVC technology is disabled (see Disabling the Stability Assist Function to disable AVC), the Aux channels will
operate as servo channels. Aux channels are not available for use in mixes when AVC is active.

Use the Steer Mix for vehicles requiring either four-wheel steering (4WS) or dual steering servos (Dual ST).

1. Select STEERING and click the scroll wheel.

2. Select 4WS and click the scroll wheel.

3. To activate, select Inhibit and scroll to select STR > AUX1.

• Select AUX1, AUX2 or AUX3 as the Slave** channel.

• The AUX channels can only be assigned to one mix at a time. If AUX1, AUX2 or

AUX3 is assigned to another mix, it will not be available as a slave channel option.

4. Select Trim to Act or Inh (Default). When Trim is Active, adjustments to the steering
trim affect both front and rear steering channels.

5. Select Switch to Assign the 4-Wheel Steering Options to a switch to select steering
options. Each time you move the switch, the 4-Wheel Steering options appear on
the Main Screen.

*Slave Channel (AUX) Example:100% means the slave channel movement is equal
to the master channel movement. If you adjust the value to 50%, the slave channel
moves half as far as the master channel. A negative value means the mix moves in the
opposite direction.

1. Select STEERING and click the scroll wheel.

2. Select 2 SERVO and click the scroll wheel.

3. To activate, select Inhibit and scroll to select STR > AUX1.

• Select AUX1, AUX2 or AUX3 as the Slave** channel.

• The AUX channels can only be assigned to one mix at a time. If AUX1, AUX2 or

AUX3 is assigned to another mix, it will not be available as a slave channel option.

*Slave Channel (AUX) Example:100% means the slave channel movement is equal
to the master channel movement. If you adjust the value to 50%, the slave channel
moves half as far as the master channel. A negative value means the mix moves in the
opposite direction.

STEER MIX

4WS (4-WHEEL STEERING)

2 SERVO (DUAL STEERING)

13

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

MIXING (CONTINUED)

Use the DUAL THROTTLE Mix on vehicles that require two throttle channels.

1. Select THROTTLE and click the scroll wheel.

2. Select Dual Throttle and click the scroll wheel.

3. To activate, select Inhibit and scroll to select THR > AUX1*.

• *Select AUX1, AUX2 or AUX3 as the slave channel.

• The AUX channels can only be assigned to one mix at a time. If AUX1,AUX2 or AUX3 is assigned to

another mix, it will not be available as a slave channel option.

To syncronize the servos use the Subtrim, Travel and Reverse menus in Servo Setup.

Use the Brake Mix on large scale vehicles that require separate front and rear brake servos. The mix value cre­ates brake bias between the front and rear brakes. Assigning the Brake Mix to a switch enables you to adjust
the mix value from any screen.

1. Select THROTTLE and click the scroll wheel.

2. Select Dual Brake and click the scroll wheel.

3. To activate, select Inhibit and scroll to select BRK > AUX1.

• Select AUX1, AUX2 or AUX3 as the slave channel.

• The AUX channels can only be assigned to one mix at a time. If AUX1,AUX2 or AUX3 is assigned to

another mix, it will not be available as a slave channel option.

The MOA Throttle Mix is used to adjust the throttle bias on rock crawlers using a “motor on axle” configuration.

1. Select THROTTLE and click the scroll wheel.

2. Select MOA and click the scroll wheel.

3. To activate, select Inhibit and scroll to select THR > AUX1.

• Select AUX1, AUX2 or AUX3 as the slave channel.

• The AUX channels can only be assigned to one mix at a time. If AUX1,AUX2 or AUX3 is assigned to

another mix, it will not be available as a slave channel option.

4. Assign a switch to the mix.

Only the rate value for the front motor can be edited. As you configure the front rate, the rear rate is updated
appropriately to show the distribution.

DUAL THROTTLE

DUAL BRAKE

MOTOR ON AXLE (MOA)

14

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

MIXING (CONTINUED)

The Programmable mixes enable you to assign any channel as a Master or Slave, which is particularly helpful
when you need to assign an Aux channel as a Master.

1. Select the desired MIX (Mix 0–3) and click the scroll wheel.

2. Scroll to MASTER and select the Master Channel. Click the scroll wheel.

3. Scroll to SLAVE and select the Slave Channel. Click the scroll wheel.

4. Select Rate to assign Rates for both Master and Slave.

5. Assign a switch to the mix. If Switch ON is selected, the value will always be on for that function.

NOTICE: A negative value results in the secondary channel moving in a direction opposite the direction of the

primary channel.

PROGRAMMABLE MIX

ACTIVE VEHICLE CONTROL (AVC)

If AVC® technology is active, only three channels, Steering ,Throttle and Aux3 are operational. The other Aux channels can be used to
power a personal transponder or lights.
If AVC technology is disabled, the Aux channels will operate as servo channels. Aux channels are not available for use in mixes when
AVC is active.

Options:

• STR Gain

• THR Gain

• Priority

To activate AVC:

• Assign a switch to toggle AVC ON/OFF or select ON.

STR Gain and/or THR Gain Sensitivity

The default value is 50%. As the value increases, the AVC steering stability and throttle management increases.
A value of 0% is off.

1. Adjust the STR Gain until you reach the ideal amount of steering control. If the front wheels begin to

shake, the STR Gain value is too high. Reduce the STR Gain value until the front wheels stop shaking. You
can assign STR Gain and THR Gain to the Switch, enabling you to adjust both values at the same time.

2. On The Fly Switch (OTF): Assigning STR Gain and THR Gain to a switch enables you to adjust the

sensitivity without using the AVC menu.

Steering Priority

As the steering angle command is increased, the steering gain is decreased. With 100% priority at full steering
travel, the steering gain is turned off to allow maximum steering control. This allows full steering stability in a
straight line, plus full steering control at full lock with varying degrees of stability proportionally based on the
steering angle. Priority is used to adjust the maximum steering rate. If the vehicle spins out, reduce the Priority.
If the vehicle won’t turn in aggressively as desired, increase the Priority.

Deactivating AVC

• Assign switch to INH.

15

Spektrum DX5r • tranSmitter inStruction manual

EN

FUNCTION LIST

AUTOMATIC BRAKING SYSTEM (ABS)

ABS helps prevent brake lock-ups and improves braking performance by pulsing the brakes.

IDLE UP

Idle up (also called high idle) is used to advance the throttle position on a gas car during startup to prevent the engine from dying
before the engine is warmed up.

Options:

• Point: The throttle position that the pulse braking takes place (0 to 100, default is 50).

• Stroke: The distance the throttle travels during the pulse braking (0 to 100, default is 50).

• Lag: The time delay before the pulsing takes place (0.0 to 2.0 in .01 increments, default is 0.0).

• Speed: The pulsing speed or frequency of the pulse braking (-1 to -30, default is -10).

To activate ABS:

1. Assign a switch to toggle ABS ON/OFF or select ON.

2. Select functions to edit.

3. The bar at the bottom of the screen displays the parameters and shows how ABS will function.

Deactivating ABS

• Assign switch to INH.

Options:

• Position: Adjusts the throttle position when idle up is engaged (0 to 100, default is 0)

• Warning: Activates an alarm when the Idle Up is active

To activate Idle Up:

1. Assign a switch to toggle Idle Up ON/OFF.

2. Select functions to edit.

3. The bar at the bottom of the screen displays the parameters and shows how Idle Up will function.
Deactivating Idle Up

• Assign switch to INH.

IMPORTANT: Idle Up must be assigned to a button in order to operate the Idle Up function .

16

Spektrum DX5r • tranSmitter inStruction manual

EN

TRACTION

Traction Control helps reduce wheel slippage and improve acceleration by gradually increasing the throttle.

TRIM SETUP

Trim Setup affects the amount the servo travels with each click of the trim, but has no effect on the total trim
travel. The trim steps range from 1 to 20 (Default is 9).

To adjust the trim steps:

CHANNEL ASSIGN

Channel Assign allows for the assigning of a switch or trimmer as input to an Aux channel.

Channel assign:

TRIM ASSIGN

Trim ASSIGN allows for the assigning of a switch to the Steering or Throttle trims.

Options:

• Point: The throttle position that traction control disengages (5 to 100, default is 50).

• Speed: The time after pulling the trigger traction control engages (1 to 100, default is 10).

To activate Traction:

1. Assign a switch to toggle Traction ON/OFF.

2. Select functions to edit.

3. Select the On The Fly (OTF) switch to edit settings with out going into the Traction menu.

4. The bar at the bottom of the screen displays the parameters and shows how Traction will function.

Deactivating Traction:

• Assign switch to INH.

1. Select channels to edit.

2. Scroll Up or Down to adjust the step value.

3. Click the scroll wheel to save the selection.

1. Select a channel to edit. Click the scroll wheel to save the selection.

2. Scroll Up/Down or toggle a switch/button to assign.

3. Click the scroll wheel to save the selection.

1. From within Trim Setup, select NEXT.

2. Select channels to assign a switch to.

3. Scroll Up/Down or toggle a switch/button to assign.

4. Click the scroll wheel to save the selection.

FUNCTION LIST

17

Spektrum DX5r • tranSmitter inStruction manual

EN

SYSTEM SETTINGS

System settings allows adjustments to the following transmitter settings:

DISPLAY

User Name

The User Name field displays your name above the model name on the main screen.

1. Scroll to the desired letter position and click the scroll wheel once. A flashing box appears.

2. Scroll Up or Down until the desired character appears. Click the scroll wheel once to save the character.

3. Scroll to the next desired letter position. Repeat Steps 1 and 2 until the Model Name is complete.
Contrast
To adjust the screen contrast:

1. Scroll to Contrast and click the scroll wheel.

2. Scroll Up or Down to adjust the contrast value. Lower numbers lighten the contrast, higher numbers

darken it.

3. Click the scroll wheel once to save the selection.
Backlight:

The Backlight field adjusts the backlight appearance time and brightness. You have the option to turn the
backlight On or Off or set how long the display stays lit (3, 10, 20, 30, 45 or 60 seconds).

Battery:

Select from Alka (default), LiIon, LiPo or NiMH battery types. Note that when the battery type is changed the
Battery alarm automatically changes for the correct type of battery chemistry.

DRIVE MODE

Every model can have up to 4 drive modes programmed to a switch or button for On-The­Fly adjustments.

Once a drive mode is selected, changes to model setup, trim and timers will only affect that drive mode.

1. Select the On The Fly (OTF) switch to switch between drive modes.

2. Scroll down to Modes; Drive Mode 1 and click the scroll wheel to rename the mode if desired.

3. Select the (+) to add a new Drive Mode.

TELEMETRY

The telemetry screen allows for easy access to all telemetry sensors and settings.

To add telemetry sensors:

1. Select an empty slot.

2. Push the scroll wheel once and scroll to find the desired telemetry sensor.

3. Click the scroll wheel to save the selection.
To edit telemetry sensors:

1. Select the sensor from the list.

2. Push the scroll wheel once to open that sensors settings.

3. Adjust sensor parameters.

4. Click the scroll wheel to save the selection.
Settings: Chose how telemetry is displayed on the transmitter.
File Settings:

• Displays File name of saved telemetry files.

• Inhibit, activate telemetry file saving.

FUNCTION LIST

• Display

• Trims

• Sounds

• About

• Calibrate

18

Spektrum DX5r • tranSmitter inStruction manual

EN

SYSTEM SETTINGS (CONTINUED)

FUNCTION LIST

Language:

Change the transmitters language.

Inactive Alarm:

An alarm activates if the transmitter sees a period of inactivity for a certain amount of time. The alarm is
helpful in reminding you to power off the transmitter and avoiding a situation where the transmitter battery
completely discharges.

• Inh (No alarm sounds)

• 5 min

• 10 min (Default)

• 30 min

• 60 min

TRIMS

Assign Trims to any trimmer or switch on the transmitter.

1. Select the Trim position from the list.

2. Push the scroll wheel once to select the position.

3. Scroll to select the Trim desired in that position.

4. Click the scroll wheel to save the selection.

SOUND SETTINGS

Turn system sounds ON/OFF.

1. Select the sound from the list.

2. Push the scroll wheel once to Activate/Inhibit.

3. Click the scroll wheel to save the selection.

ABOUT

Displays the transmitter’s Serial Number.

CALIBRATE

Use this menu to calibrate controls. After making any physical transmitter changes it is recommended to
calibrate the transmitter.

1. Move the Steering Wheel, Throttle/Brake and the knob from stop to stop.

2. Centert the knob.

3. Save when finished or cancel to go back.

Alarm:

Set the low voltage for each battery type. The recommended low voltage threshold is set by default for each
battery type.

CAUTION: Never select NiMH when a LiPo/Li-Ion battery is installed in the transmitter. Doing so may over­discharge the LiPo battery and damage the battery, transmitter or both.

CAUTION: Never adjust the low voltage limit for the LiPo/Li-Ion battery pack below 6.4V. Doing so could
over-discharge the battery pack and damage both battery pack and transmitter.

19

Spektrum DX5r • tranSmitter inStruction manual

EN

Press and hold the scroll wheel while powering on the transmitter to show the System Setup list. No radio transmission occurs when a
System Setup screen is displayed, preventing accidental damage to linkages and servos during changes to programming.

You can also enter the System Setup from the Function list without turning the transmitter off. A Caution screen will appear that warns
that RF will be disabled (the transmitter will no longer transmit). Press YES if you are sure and want to access
the System List. If you are not sure, press NO to exit to the main screen and continue operation.

If you do not press YES or NO, the system will exit to the main screen and continue operation within
approximately 10 seconds.

WARNING: Do not press YES unless the model is turned off and secured.

SYSTEM SETUP

MODEL SELECT

MODEL UTILITIES

Model Select enables you to access any of the 250 internal model memory locations in the Model Select list.

1. Scroll to the desired model memory in the Model Select list.

2. When the desired model memory is highlighted, click the scroll wheel once to select the model. The

transmitter returns to the Main Screen.

3. Add a new model by rolling to the bottom of the list. You will then be prompted with the Create New

Model screen.

CAUTION: NEVER change the model in Model Select while operating a model. Changing the model
memory interrupts the transmitter signal to the receiver and may cause loss of vehicle control,
damage or personal injury.

In the Model Utilities function you can create a new model,delete a model, copy a model, reset a model to default
settings and sort the model list.

20

Spektrum DX5r • tranSmitter inStruction manual

EN

1. Select the CREATE NEW MODEL and click the scroll wheel.

2. Select CREATE to create a new model or CANCEL to go back.

3. The new model is available in the model select list.

CAUTION: NEVER change the model in Model Select while operating a model. Changing the model

memory interrupts the transmitter signal to the receiver and may cause loss of vehicle control,
damage or personal injury.

Use this selection to permanently delete a model from the model select list. If you do not wish to delete a
model, select Cancel to exit the page.

1. To delete a model, highlight the model listed. Press to select then roll to the model name. Click the scroll

wheel to select.

2. Select DELETE to delete the model.

Use the Model Reset menu to delete all model programming in the active model memory. Reset returns all
model settings to the default settings and erases all programming in the selected model.

IMPORTANT: After a model reset, it is necessary to re-bind.

With this function you can sort the model order in the model select function. This is helpful to group similar
models together to make them easy to find. To move a model, highlight the model that you wish to move with
the scroll wheel, then click the scroll wheel to select it. Scroll the scroll wheel to move the selected model to
the position desired. Click the scroll wheel when you have the model in the position desired.

The Model Copy menu enables you to duplicate model programming from one Model List location to another.

Use Model Copy to:

• Save a default model copy before experimenting with programming values

• Expedite programming for a model using a similar programming setup

IMPORTANT: Copying a model program from one model memory to another will erase any programming in the
“To” model memory.

To copy model programming:

1. Select where to save the copied memory by selecting “TO” and scroll to ADD NEW MODEL. Click the

scroll wheel once to save the selection. To save over a current model select that model from the list.

2. Select the model to be copied by selecting “From” and scroll to the model to be Copied.

3. Scroll down to COPY at the bottom of the screen and click the scroll wheel once.

4. Confirm the copy by selecting COPY or CANCEL to go back.

You cannot use the Model Copy screen to copy model programming to an SD Card. To copy model
programming to the SD Card, please see “Transfer SD Card”.

SYSTEM SETUP

CREATE NEW MODEL

DELETE MODEL

RESET MODEL

SORT MODEL LIST

COPY MODEL

21

Spektrum DX5r • tranSmitter inStruction manual

EN

SYSTEM SETUP

TRANSFER SD CARD

IMPORT MODEL

EXPORT MODEL

UPDATE FIRMWARE

The SD Card enables you to:

To import an individual model file from the SD
Card:

1. Save the model file to the SD Card and insert

into the transmitter.

2. In the Transfer SD Card menu, scroll to Options

and click the scroll wheel once.

3. Scroll to Import Model and press the scroll

button again to save the selection. The Select
File screen appears.

4. Select the model file you wish to import. The

Import Model screen appears.

5. Select Import to save the model to the

transmitter. The new model will be appended to
the end of the model list.

Import All Models

To import all models from the SD Card:

1. Select Import All Models.

2. Confirm by selecting IMPORT.
IMPORTANT: After importing a model, you must

rebind the transmitter and receiver.

You can use the Export Model option to export a
single model file to the SD Card.

1. Make sure the active model file is the one you

wish to Export.

2. In the Transfer SD Card menu, scroll to Options

and click the scroll wheel once.

3. Scroll to Export Model and click the scroll wheel

again to save the selection. The Export to SD
screen appears. The first two characters of the
file name correspond to the Model List number
(01, for example).

4. Select Export to save the file to the SD Card.

When the export is complete, the transmitter
returns to the SD Card Menu screen.

Export All Models

To export all models to the SD Card:

1. Select Export All Models in the Transfer SD Card

Menu options. The Export All Models screen
appears.

IMPORTANT: Export All Models will overwrite any
model files that have the same name. Always save
model files to a different SD card if you are not sure.

2. Select Export to overwrite files on the SD Card

or Cancel to return to the SD Card Menu.

Before installing any files, always Export All Models to
an SD Card separate from the SD Card containing the
update. The update may erase all model files.

Automatically Installing Firmware

1. Download the update from spektrumrc.com and

save it to the SD Card.

2. Power off the transmitter and install the SD

Card in the transmitter.

3. Power on the transmitter and the update

automatically installs in the transmitter.

Manually Installing AirWare Software Updates

1. Save the desired Firmware to the SD Card.

2. Select Update Firmware in the SD Card Menu

options. The Select File screen appears.

3. Select the desired Firmware version from

the File List. When updates are installing, the
transmitter screen is dark. The orange LED
Spektrum bars flash and the update status bar
appears on the screen.

NOTICE: Do not power off the transmitter when
updates are installing. Doing so will damage the
transmitter.

• Import model(s) from another
DX5R transmitter

• Export model(s) to another
DX5R transmitter

• Update firmware in the
transmitter

22

Spektrum DX5r • tranSmitter inStruction manual

EN

PHYSICAL TRANSMITTER ADJUSTMENTS

The DX5R is designed to be extremely adjustable to suite a wide
variety of driver needs. Available adjustments are:

• Adjustable trigger and steering tension

• Multiple trigger position

• Multiple wheel drop-down options

• 2 optional grip sizes (not included)

• 10˚ and 15˚ Steering Adapters (not included)

• Small and Large Steering Wheel (small wheel not included)

• Lift the edge of the grip and pull the grip away from the

handle.

• Align the tabs on the new grip with the slots in the handle.

• Press the grip against the handle.

Steering Tension Adjustment

Turn the screw clockwise with the 1.5mm hex wrench to
increase the steering tension.

Throttle Distance Adjustment

Loosen the bolt with a 2.5mm hex wrench. Move the throttle
trigger in or out and tighten.

Throttle Tension Adjustment

Turn the screw clockwise with the 1.5mm hex wrench to
increase the trigger tension.

CHANGING GRIPS

The DX5R comes with the medium-size grip installed at the
factory. To install optional (sold seperatly) size grips:

23

Spektrum DX5r • tranSmitter inStruction manual

EN

PHYSICAL TRANSMITTER ADJUSTMENTS

• Turn off the DX5R

• Using a 2mm hex wrench, remove 3 screws.

• Rotate the drop down to the desired angle.

• Align with the screw holes and re-install the 3 screws

being careful not to pinch any wires.

• Using a 2mm hex wrench, remove the 3 screws from the
drop down and remove the drop down from the transmitter.
Carefully disconnect the 2 wiring harness from inside the
transmitter.

• Using a 1.5mm hex wrench, remove the steering
wheel.

• Using a 2mm hex wrench, remove 2 screws from
the steering mechanism. Remove the steering
mechanism from the drop down being careful to
pull the wiring harness through the opening.

• Keep the drop down in a safe place for future
use.

• Connect the 2 wiring harnesses to the board
inside the DX5R. Note that one connector has 6
pins and the other has 7.

• Re-install the steering mechanism directly onto
the transmitter using the 2 screws.

• Re-install the steering wheel.

• Refer to the Dropdown steering wheel options section

above for directions on removing and installing the steering
mechanism.

• The wedge goes between the steering mechanism and
the drop down (or transmitter if the drop down is not being
used) and can be rotated to almost any angle.

ROTATE:

DROPDOWN STEERING WHEEL OPTIONS

The DX5R comes with the dropdown wheel installed. The drop­down can be rotated for a perfect feel or removed for a standard
wheel layout. All the parts necessary to convert to the standard
wheel are included.

STANDARD WHEEL CONVERSION:

STEERING WHEEL WEDGES (NOT INCLUDED)

Wiring not shown

CAM

15º

10º

24

Spektrum DX5r • tranSmitter inStruction manual

EN

RECEIVER COMPATIBILITY

The DX5R transmitter is compatible with Spektrum™ DSMR®
receivers. The inlcuded Spektrum SR6000T* Telemetry Surface
receiver is compatible with all Spektrum DSMR transmitters and
is also backwards compatible with DSM2 transmitters.

Receiver Installation and Setup

Install the Receiver in your vehicle using double-sided foam servo tape. Foam servo tape will hold the receiver in place and help isolate
it from vibrations.

Mount the antenna up and away from the vehicle. The higher up the antenna is, the better signal it will receive.

NOTICE: Do not cut or modify the antenna.

Powering the receiver with an ESC

Receiver

Battery To Motor

Electronic

Speed Control

Steering Servo

Steering Servo

Throttle Servo

Battery

Receiver

Powering the receiver with a separate receiver pack

1. Push and hold the bind button on the receiver while

powering up the receiver. The orange LED will flash
continuously, indicating that the receiver is in bind mode.

Tip: It is possible to use a bind blug in the BIND/BATT port if
desired.

2. With all channels in the desired preset failsafe position

(normally neutral), put your transmitter in bind mode.
Continue holding the failsafe position until the binding
process is complete.

3. The bind process is complete when the orange LED on

the receiver is solid.

CAUTION: When the bind process is complete,
the throttle and steering channels are active. Keep
hands and loose objects away from all spinning
parts on the vehicle.

Binding

A: Voltage sensor port
B: Temperature sensor port
C: Bind Button
D: Antenna
E: RPM sensor port
F: XBUS Port
G: Servo ports-

D

E

F

G

A

B

C

•Bind/Battery

•Steering

•Throttle

•Aux1-Aux4

*For more information on the SR6000T receiver, see the
receivers full manual.

PART # PARTS DESCRIPTION

SPM6719 Spektrum DX6R Transmitter Case
SPM9050 Grip Set, S, M, L: DX6R
SPM9052 Small Wheel w/Foam: DX6R
SPM9053 Wedges, 10/15 Deg: DX6R
SPM9055 Wheel Cam Set, 32/36 Deg: DX6R
SPM9058 Grip Attachment Tape: DX6R

OPTIONAL PARTS LIST

25

Spektrum DX5r • tranSmitter inStruction manual

EN

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

The system will not
connect

Transmitter and receiver too near each other Move transmitter 8 to 12 feet (2.4 to 3.6m) from receiver
Transmitter and receiver too near large

metal objects (vehicles, etc.)

Move away from large metal objects (vehicles, etc.)

Selected model is not bound in transmitter Make sure correct model memory is selected and that

transmitter is bound to the model

Transmitter accidentally put in bind mode so
receiver is no longer bound

Rebind transmitter and receiver

The receiver goes
into failsafe mode a
short distance away
from the transmitter

Check the receiver antenna to be sure it is
not cut or damaged

Replace or contact Horizon product Support

Make sure receiver antenna is in an antenna tube and is
above vehicle

Receiver quits
responding during
operation

Low battery voltage Completely recharge battery
Loose or damaged wires or connectors

between battery and receiver

Do a check of the wires and connection between battery
and receiver. Repair or replace wires and/or connectors

Receiver loses its
bind

Transmitter accidentally put in bind mode,
ending bind to receiver

Bind transmitter to receiver

Receiver taking lon­ger than usual to link
with transmitter

Transmitter and receiver are operating on
Marine model

Marine receivers can take longer to link with transmitter

1-YEAR LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser
that the product purchased (the “Product”) will be free from
defects in materials and workmanship for a period of 1 year from
the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic
damage, (ii) damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a Horizon
Hobby authorized service center, (v) Product not purchased
from an authorized Horizon dealer, (vi) Product not compliant
with applicable technical regulations or (vii) use that violates any
applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i) service,
or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved
in a warranty claim. Service or replacement decisions are at
the sole discretion of Horizon. Proof of purchase is required for

all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no
event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control
over use, setup, final assembly, modification or misuse, no liability
shall be assumed nor accepted for any resulting damage or injury.
By the act of use, setup or assembly, the user accepts all resulting
liability. If you as the purchaser or user are not prepared to accept
the liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused
condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conflict
of law principals). This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
Horizon reserves the right to change or modify this warranty at any
time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor

26

Spektrum DX5r • tranSmitter inStruction manual

EN

WARRANTY AND SERVICE CONTACT INFORMATION

Country of

Purchase

Horizon Hobby Contact Information Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

4105 Fieldstone Rd Champaign, Illinois,

61822 USA

Horizon Product Support

(Product Technical Assistance)

[e-mail]

877-504-0233

Sales

[e-mail]

800-338-4639

EU

Horizon Technischer Service [e-mail]

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH [phone]

10-15

or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any
assistance. For questions or assistance, please visit our website
at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty
and Service Contact Information section to speak with a Product
Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant
in the country you live and use the Product in, please use the
Horizon Online Service Request submission process found on
our website or call Horizon to obtain a Return Merchandise
Authorization (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be included,
but are not designed to withstand the rigors of shipping without
additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted at
our facility. An Online Service Request is available at http://www.
horizonhobby.com/content/_service-center_render-service­center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions
for submitting your product for service. When calling Horizon,
you will be asked to provide your complete name, street address,
email address and phone number where you can be reached
during business hours. When sending product into Horizon, please
include your RMA number, a list of the included items, and a brief
summary of the problem. A copy of your original sales receipt
must be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside of the
shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you
have any issue with a LiPo battery, please contact the
appropriate Horizon Product Support office.

Warranty Requirements

For Warranty consideration, you must include your original sales
receipt verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be serviced or
replaced free of charge. Service or replacement decisions are at
the sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service

will be completed and payment will be required without
notification or estimate of the expense unless the expense
exceeds 50% of the retail purchase cost. By submitting the

item for service you are agreeing to payment of the service without
notification. Service estimates are available upon request. You
must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of
½ hour of labor. In addition you will be billed for return freight.
Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to
Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership. If
received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through a
carrier of the sender’s choice and at the sender’s expense.
Horizon will hold non-compliant Product for a period of 60
days from notification, after which it will be discarded.

27

Spektrum DX5r • tranSmitter inStruction manual

EN

FCC ID: BRWDAMTX12

This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless
technology which has been tested and found to be compliant
with the applicable regulations governing a radio transmitter in
the 2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your Spektrum
transmitter, please be sure to
maintain a separation distance of
at least 5 cm between your body
(excluding fingers, hands, wrists,
ankles and feet) and the antenna
to meet RF exposure safety
requirements as determined by
FCC regulations.

The illustrations show the
approximate 20 cm RF exposure
area and typical hand placement
when operating your Spektrum
transmitter.

This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, Including interference that may
cause undesired operation of the device.

FCC INFORMATION

IC INFORMATION

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other
relevant provisions of the RED Directive.

A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by
handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection

and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a
manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling,
please contact your local city office, your household waste disposal service or where you purchased the product.

20 cm

IC: 6157A-AMTX12

48104.1

© 2017 Horizon Hobby, LLC.

DSM, DSM2, DSMR, AVC, Active Vehicle Control and RaceWare are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

All other trademarks, service marks and logos are property of their respective owners.

US 9,320,977. Other patents pending.

3/17