Quick Start Guide
SG 105(w)/115(w)/125(w)/135(w) Rev. 3
1
1. Before Deploying
Congratulations on your purchase of the Sophos SG appliance to protect your data
networks and computers. This Quick Start Guide describes in short steps how
to assemble the appliance and explains how to open the web-based WebAdmin
configuration tool on the security system from your administration client PC.
WebAdmin allows you to configure every aspect of the security system.
a) What does the box include
b) Device Images: Back Side
*
Quick Start Guide SG 105(w)/115(w)/125(w)/135(w)
Before you begin please confirm that you have a
working Internet connection and make sure you
have the account information available that was
provided by your ISP.
1 x COM
(RJ45)
3 x external
antenna
(SG 125w and
SG 135w only)
2 x USB
2.0
8 x GbE
copper port
Power
Supply
Optional
2nd
redundant
power
supply
1 x
Micro
USB
1 x
HDMI
Expansion bay (shown with
optional module incl. 2 antennas)
1 x GbE
SFP
SG 105(w)/115(w)/125(w)/135(w) This Quick Start Guide and
Security Notes
SG 105(w)/115(w) - 2 antennas;
SG 125(w)/135(w) - 3 antennas
Power Adapter
(region specific)
Micro USB cable
RJ45 Ethernet cable
SG 105w/115w Rev. 3 SG 125w/135w Rev. 3
1 x COM
(RJ45)
2 x external antenna
(SG 105w and SG 115w only)
2 x USB
2.0
4 x GbE
copper port
Power
Supply
Optional
2nd
redundant
power
supply
1 x
Micro
USB
1 x
HDMI
1 x GbE SFP
(shared)
* The displayed back image is of the SG 115 and SG 135 device.
2
License
The security appliances are delivered with a 30-day trial version. During or after
the trial period, you can activate the full license you purchased from your Sophos
partner by creating an account at https://myutm.sophos.com, activating the provided
activation and upgrade keys, and uploading the created license file into your appliance.
2. Mount and connect the device
Connect the ports to the internal and external networks
1. Connect the E0/LAN port via a hub or switch to the internal network. For this
purpose, please use the RJ45 Ethernet cable of the scope of supply. Note that your
administration client PC must also be connected to this network.
2. Connect the E1/WAN port to the external network. The connection to the WAN
depends on the type of Internet access.
The UTM appliances are shipped with the following default settings:
Ethernet Port IP Address Zone
E0/LAN 192.168.0.1/255.255.255.0 LAN
Default Gateway DNS Proxy DHCP Service
None Enabled Disabled
Note: On SG 105(w)/115(w) the SFP port is shared with RJ45 Ethernet Port E3 and
takes precedence over RJ45 port in case you connect cables in both ports at the same
time.
Mount the appliance to the rack
If you want to mount the device within a rack please use the optionally available
rackmount kit for this device.
Internet
e.g.,
DSL modem
Internal network
admin client PC
UTM Appliance
Switch
E1/any port
E0/LAN
Quick Start Guide SG 105(w)/115(w)/125(w)/135(w) Rev. 3
3
3. Power Up the Device
Connect the power adapter(s) and turn on the device
Connect the provided power adapter to connector 1 on the back of the device. In order
to increase redundancy you can connect an optionally available second power adapter
of the same type to power connector 2.
Turn the device on. The power switch is on the back of the device and is placed next to
the power connection.
During boot up the Status LED on the front will blink green. Once the device has booted
completely the Status LED will turn to solid green.
4. Configure the device
Use your browser to make the initial connection to the WebAdmin GUI
You will need to configure a workstation with the necessary LAN properties to access
WebAdmin. You can change these settings later to match your existing network. The
location of the menu for these settings depends on the operating system of your client.
Example: With Windows 7, the menu can be found under Start >> Control Panel >>
Network and Sharing Center
Start the browser and enter the management IP address of the appliance:
https://192.168.0.1:4444
Accept the security notice by clicking OK (Mozilla Firefox) or Yes (MS Internet Explorer).
For configuration you can follow the initial setup wizard described in the WebAdmin
Quick Start Guide** or cancel it and perform a manual setup (see the UTM
Administration Guide*).
Workstation connection properties:
IP address: Any address in the range 192.168.0.2
through 192.168.0.254
Netmask: Enter 255.255.255.0
Standard gateway: Enter the IP address of
the appliance’s internal network card E0/LAN:
192.168.0.1
DNS server: Enable this option and enter the IP
address of the internal network card E0/LAN:
192.168.0.1
* Available at www.sophos.com/en-us/support/documentation/sophos-utm
** Available via WebAdmin >> Support >> Manual
Quick Start Guide SG 105(w)/115(w)/125(w)/135(w) Rev. 3
4
5. Device LED Status
LEDs on each RJ45 Ethernet connector
ACT/LNK
(Left LED)
Green Constantly 1. The Ethernet port is receiving power.
2. Good connection between the Ethernet port
and hub.
Flashing The adapter is sending or receiving network data.
The frequency of the flashes varies with the
amount of traffic.
Off 1. The adapter and switch are not receiving power.
2. No connection between both ends of network.
3. Network drivers have not been loaded or do not
function correctly.
Speed
(Right LED)
Amber On The Ethernet port is operating at 1,000 Mbps
Green On The Ethernet port is operating at 100 Mbps
Off The Ethernet port is operating at 10 Mbps
LEDs on SFP connector
ACT/LNK
(Left LED)
Green Constantly 1. The SFP connector is receiving power.
2. Good connection between the SFP connector
and hub.
Flashing The adapter is sending or receiving network data.
The frequency of the flashes varies with the
amount of traffic.
Off 1. The adapter and switch are not receiving power.
2. No connection between both ends of network.
3. Network drivers have not been loaded or do not
function correctly.
Speed
(Right LED)
Amber On The Ethernet port is operating at 1,000 Mbps
Quick Start Guide SG 105(w)/115(w)/125(w)/135(w) Rev. 3
LEDs on front
Storage Blue Flashing SSD drive is being accessed
Status Green Constantly Normal operation
Flashing Device is booting up or shutting down
Red Constantly SSD or boot failure
Flashing General error (please contat support)
Wifi Green On Wifi is active
Off Wifi is inactive
Power 1 Green Constantly Power adapter 1 in normal operation
Red Constantly Power adapter 1 failed or disconnected
Power 2 Green Constantly Power adapter 2 in normal operation
Red Constantly Power adapter 2 failed or disconnected
Device Images: Front Side
*
Status LEDs
(w-model has additional Wi-Fi LED)
6. Support and Documentation
For more information and technical support, please visit
www.sophos.com/en-us/support or contact your local Sophos
reseller.
* The displayed front image is of the SG 115 and SG 135 device.
5
1. Vorbereitung
Herzlichen Glückwunsch zum Kauf dieser Sophos SG Appliance zum Schutz Ihrer
Datennetzwerke und Computer. Dies e Kurzanleitung beschreibt schrittweise die
Montage der Appliance und erläutert, wie Sie über Ihren Administrations-Client-PC das
webbasierte WebAdmin Konfigurationstool auf dem Sicherheitssystem öffnen. Mit
WebAdmin können Sie jeden Aspekt des Sicherheitssystems konfigurieren.
a) Verpackungsinhalt
b) Abbildungen der Appliance: Rückseite
*
Kurzanleitung SG 105(w)/115(w)/125(w)/135(w) Rev. 3
Bevor Sie beginnen, vergewissern Sie sich, dass
Sie mit dem Internet verbunden sind und die
Kontodaten vorliegen, die Sie von Ihrem ISP
erhalten haben.
SG 105(w)/115(w)/125(w)/135(w) Diese Kurzanleitung und
Sicherheitshinweise
SG 105(w)/115(w) – 2 Antennen,
SG 125(w)/135(w) – 3 Antennen
Netzadapter
(regionenspezifisch)
Micro USB-Kabel
RJ45 Ethernet-Kabel
1 x COM
(RJ45)
3externe
Antennen
(nur SG125w
und SG135w)
2 x USB
2.0
8 x Kupferport
GbE
Stromversorgung
Optionale zweite
redundante
Stromversorgung
1 x
Micro
USB
1 x
HDMI
Erweiterungsschacht
(abgebildet mit optionalem
Modul einschl. 2Antennen)
1 x GbE
SFP
SG 105w/115w Rev. 3 SG 125w/135w Rev. 3
1 x COM
(RJ45)
2externe Antennen
(nur SG105w und SG115w)
2 x USB
2.0
4 x Kupferport
GbE
Stromversorgung
Optionale zweite
redundante
Stromversorgung
1 x
Micro
USB
1 x
HDMI
1 x GbE SFP
(geteilt)
* Die Abbildung der Rückseite bezieht sich auf die SG 115 und SG 135 Appliance.
Loading...