Sony XAV-W651BT, XAV-W601, XAV-V631BT User Manual
4-687-624-33(1)
AV Center
Operating Instructions
GB
To cancel the demonstration (Demo) display, see page 20.
For the connection/installation, see page 31.
XAV-W651BT/XAV-V631BT/XAV-W601
For safety, be sure to install this unit in the
(For Singapore models only)
dashboard of the car as the rear side of the unit
becomes hot during use.
For details, see “Connection/Installation”
(page 31).
This manual contains instructions for XAVW651BT, XAV-V631BT, and XAV-W601.
XAV-W651BT is the model representatively used
for illustration purposes.
Laser Diode Properties
Emission Duration: Continuous
Laser Output: Less than 46.8 W
(This output is the value measurement at a distance
of 70 mm from the objective lens surface on the
Optical Pick-up Block with 7 mm aperture.)
The nameplate indicating operating voltage, etc., is
located on the bottom of the chassis.
The validity of the CE marking is restricted to only
those countries where it is legally enforced, mainly
in the countries EEA (European Economic Area).
Warning
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
CAUTION
The use of optical instruments with this product will
increase eye hazard. As the laser beam used in this
CD/DVD player is harmful to eyes, do not attempt
to disassemble the cabinet. Refer servicing to
qualified personnel only.
WARNING: Do not ingest battery,
Chemical Burn Hazard.
The remote commander contains a coin/
button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in just
2 hours and can lead to death.
Keep new and used batteries away from children. If
the battery compartment does not close securely,
stop using the product and keep it away from
children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
Note on the lithium battery
Do not expose the battery to excessive heat such as
direct sunlight, fire or the like.
Warning if your car’s ignition has no ACC
position
After turning the ignition off, be sure to press
and hold HOME on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
Disclaimer regarding services offered by third
parties
Services offered by third parties may be changed,
suspended, or terminated without prior notice.
Sony does not bear any responsibility in these sorts
of situations.
Disposal of waste batteries and
electrical and electronic equipment
(applicable in the European Union
and other European countries with
separate collection systems)
2GB
Important notice (XAV-W651BT/XAVV631BT)
Caution
IN NO EVENT SHALL SONY BE LIABLE FOR ANY
INCIDENTAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OR OTHER DAMAGES I NCLUDING,
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF
REVENUE, LOSS OF DATA, LOSS OF USE OF THE
PRODUCT OR ANY ASSOCIATED EQUIPMENT,
DOWNTIME, AND PURCHASER’S TIME RELATED TO
OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS
HARDWARE AND/OR ITS SOFTWARE.
Dear customer, this product includes a radio
transmitter.
Please check your vehicle operation manual or
contact the manufacturer of your vehicle or your
vehicle dealer, before you install this product into
your vehicle.
Emergency calls
This BLUETOOTH car handsfree and the electronic
device connected to the handsfree operate using
radio signals, cellular, and landline networks as well
as user-programmed function, which cannot
guarantee connection under all conditions.
Therefore do not rely solely upon any electronic
device for essential communications (such as
medical emergencies).
On BLUETOOTH communication
• Microwaves emitting from a BLUETOOTH device
may affect the operation of electronic medical
devices. Turn off this unit and other BLUETOOTH
devices in the following locations, as it may cause
an accident.
– where inflammable gas is present, in a hospital,
train, airplane, or petrol station
– near automatic doors or a fire alarm
• This unit supports security capabilities that
comply with the BLUETOOTH standard to provide
a secure connection when the BLUETOOTH
wireless technology is used, but security may not
be enough depending on the setting. Be careful
when communicating using BLUETOOTH wireless
technology.
• We do not take any responsibility for the leakage
of information during BLUETOOTH
communication.
If you have any questions or problems concerning
your unit that are not covered in this manual,
consult your nearest Sony dealer.
3GB
Table of Contents
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5
Getting Started
Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing a BLUETOOTH Device
(XAV-W651BT/XAV-V631BT) . . . . . . . . . . . . . . . . 7
Connecting a USB Device . . . . . . . . . . . . . . . . . . . . . 9
Connecting Other Portable Audio/Video
Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting Rear View Camera . . . . . . . . . . . . . . . . 9
Listening to the Radio
Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . 10
Using Radio Data System (RDS) . . . . . . . . . . . . . . . 11
Playback
Playing a Disc (XAV-W651BT/XAV-W601) . . . . . . . 11
Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 12
Playing a BLUETOOTH Device
(XAV-W651BT/XAV-V631BT) . . . . . . . . . . . . . . . 13
Searching and Playing Tracks. . . . . . . . . . . . . . . . . 13
Other Settings During Playback. . . . . . . . . . . . . . . 14
Listening to Pandora® (Australia and
New Zealand model of XAV-W651BT/
XAV-W601)
Setting Up Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 14
Streaming Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 14
Available Operations in Pandora® . . . . . . . . . . . . . 15
Additional Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance (except for Oceania and Middle East
model XAV-W601). . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Language Code List
(XAV-W651BT/XAV-W601) . . . . . . . . . . . . . . . . 30
Connection/Installation
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Parts List for Installation . . . . . . . . . . . . . . . . . . . . 31
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Handsfree Calling (via BLUETOOTH
only) (XAV-W651BT/XAV-V631BT)
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Available Operations During a Call . . . . . . . . . . . . 16
Useful Functions (XAV-W651BT/XAVV631BT)
SongPal with Android Phone . . . . . . . . . . . . . . . . . 16
Using Siri Eyes Free . . . . . . . . . . . . . . . . . . . . . . . . . 18
Settings
Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 18
General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Visual Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4GB
Guide to Parts and Controls
Main unit
SOURCE
Change the source. Each time it is pressed, it
displays a selectable source in a popup on the
current display.
VOICE (XAV-W651BT/XAV-V631BT)
Press and hold to activate the voice command
function.
To assign the DSPL function to this button, select
[DSPL] in [SOURCE Key Func.] (page 19).
DSPL (display) (XAV-W601)
Press and hold to open the display menu.
The monitor off function can be set on the
display menu.
When the monitor off function is activated and
the monitor is turned off, touch anywhere on the
display to turn it back on.
Volu me control di al
Rotate to adjust the volume.
N-Mark (except for XAV-W601 and Indian
model XAV-V631BT)
Makes a BLUETOOTH connection when touched
with an Android™ phone.
HOME
Turn o n the p ower.
Open the HOME menu.
Press to pause playback when Disc (XAVW651BT/XAV-W601), iPod/USB, BT Audio (XAVW651BT/XAV-V631BT) or Pandora (Australia and
New Zealand model of XAV-W651BT/XAV-W601)
source is selected.
To r esu m e pl ayba c k, t ouc h .
Press and hold for more than 2 seconds to turn
off the unit. When the unit is turned off, remote
commander operation is not available (except
for Oceania and Middle East model XAV-W601).
ATT (attenuate)
Press and hold for a second, but less than 2
seconds, then rotate the volume control dial to
attenuate the sound.
Receptor for the remote commander
Disc slot (XAV-W651BT/XAV-W601)
(disc eject) (XAV-W651BT/XAV-W601)
USB port
AUX input jack
Reset button
Display/touch panel
5GB
RM-X170 remote commander
(except for Oceania and Middle East
model XAV-W601)
The remote commander can be used to operate the
audio controls. For menu operations, use the touch
panel.
DVD playback setting buttons (XAV-W651BT/
XAV-W601)
ZAP (ZAPPIN™) (page 10)
///
Select a setup item, etc.
ENTER
Enter the selected item.
MODE
Select the radio band.
VOL (volume) +/–
Remove the insulation film before use.
Screen displays
Playback screen:
OFF
Tur n t he s ou rce o ff .
Press and hold for 2 seconds to turn off the
power and display.
MONITOR OFF
Turn off the monitor.
To turn back on, press again.
POSITION
This button is not supported.
(return)
Return to the previous display.
Return to the menu on a Video CD (VCD) (XAVW651BT/XAV-W601).
EQ (equalizer)
Select an equalizer curve.
Number buttons (0 – 9)
CLEAR
(play/pause)
/ (previous/next)
/ (fast-re verse/fast-forward)
6GB
Home screen:
Status indication
Lights up when the sound is attenuated.
Lights up when the “SongPal”
connection is established between this
unit and your Android phone. (XAVW651BT/XAV-V631BT)
Lights up when the BLUETOOTH signal is
on. Flashes when the connection is in
progress. (XAV-W651BT/XAV-V631BT)
Lights up when the audio device is
playable by enabling the A2DP
(Advanced Audio Distribution Profile).
(XAV-W651BT/XAV-V631BT)
Lights up when handsfree calling is
available by enabling HFP (Handsfree
Profile). (XAV-W651BT/XAV-V631BT)
Indicates the signal strength status of
the connected cellular phone. (XAVW651BT/XAV-V631BT)
Indicates the remaining battery status of
the connected cellular phone. (XAVW651BT/XAV-V631BT)
(EXTRA BASS)
Touch to select the EXTRA BASS setting: [1], [2],
[off].
(sound setting menu)
Access the sound setting menu directly
(page 19).
(option)
Open the option menu. The available items
differ depending on the source.
Clock (page 7)
When the AUX or Rear Camera source is
selected, the clock is not displayed.
Application specific area
Display playback controls/indications or show
the unit’s status. Displayed items differ
depending on the source.
(return to the playback screen)
Switch from the HOME screen to the playback
screen.
/
Move to the next/previous page (This does not
necessarily appear on the screen).
Sources and Settings select keys
Change the source or make various settings.
Getting Started
Resetting the Unit
You must reset the unit before operating the unit
for the first time, after replacing the car battery, or
changing connections.
Note
Pressing the reset button will erase the clock setting and
some stored contents.
Setting the Clock
1 Press HOME, then touch [Settings].
2 Touch , then touch [Clock Adjust].
The setting display appears.
3 Tou ch / to set the hour and minute.
4 After setting the hour and minute, touch
[Set].
The setting is complete and the clock starts.
Preparing a BLUETOOTH Device (XAV-W651BT/XAV-V631BT)
You can enjoy music or perform handsfree calling
depending on the BLUETOOTH compatible device
such as smartphones, cellular phones, and audio
devices (hereafter “BLUETOOTH device” if not
otherwise specified). For details on connecting,
refer to the operating instructions supplied with the
device.
Before connecting the device, turn down the
volume of this unit; otherwise, a loud sound may
result.
7GB
Connecting with a smartphone by One
[0000]
Input passkey
touch (NFC) (except for Indian model
XAV-V631BT)
By touching the N-Mark on the unit with an NFC*
compatible smartphone, the unit is paired and
connected with the smartphone automatically.
* NFC (Near Field Communication) is a technology enabling
short-range wireless communication between various
devices, such as mobile phones and IC tags. Thanks to the
NFC function, data communication can be achieved easily
just by touching the relevant symbol or designated
location on NFC compatible devices .
For a smartphone with Android OS 4.0 or lower
installed, downloading of the app “NFC Easy
Connect” available at Google Play™ is required. The
app may not be downloadable in some countries/
regions.
1 Activate the NFC function on the
smartphone.
For details, refer to the operating instructions
supplied with the smartphone.
2 Touch the N-Mark part of the unit with the
N-Mark part of the smartphone.
Pairing and connecting with a
BLUETOOTH device
When connecting a BLUETOOTH device for the first
time, mutual registration (called “pairing”) is
required. Pairing enables this unit and other devices
to recognize each other.
1 Place the BLUETOOTH device within 1 m (3
ft) of this unit.
2 Press HOME, then touch [Settings].
3 Touch .
4 Touch [Bluetooth Connection], then set the
signal to [ON].
The BLUETOOTH signal i s turned on an d lights
up on the status bar of the unit.
5 Touch [Pairing].
flashes while the unit is in pairing standby
mode.
6 Perform pairing on the BLUETOOTH device
so it detects this unit.
7 Select [XAV-xxxx] (your model name) shown
in the display of the BLUETOOTH device.
If your model name does not appear, repeat
from step 5.
Make sure that lights up on the status bar of
the unit.
To disconnect by One touch
Touch the N-Mark part of the unit with the N-Mark
part of the smartphone again.
Notes
• When making the connection, handle the smartphone
carefully to pre vent scratches.
• One touch connection is not possible when the unit is
already connected to another NFC compatible device. In
this case, disconnect the other device, and make a
connection with the smartphone again.
8GB
8 If passkey* input is required on the
BLUETOOTH device, input [0000].
* Passkey may be called “passcode,” “PIN code,” “PIN
number,” “password,” etc., depending on the
BLUETOOTH device.
When pairing is made, stays lit.
9 Select this unit on the BLUETOOTH device to
establish the BLUETOOTH connection.
or lights up when the connection is made.
Note
While connecting to a BLUETOOTH device, this unit cannot
be detected by another device. To enable detection, ente r
the pairing mode and search for this unit from another
device.
To start playback
For details, see “Playing a BLUETOOTH Device (XAVW651BT/XAV-V631BT)” (page 13).
To c a nce l pai rin g
Perform step 5 to cancel the pairing mode after this
unit and the BLUETOOTH devices are paired.
Connecting with a paired BLUETOOTH
device
To use a paired device, connection with this unit is
required. Some paired devices will connect
automatically.
1 Press HOME, then touch [Settings].
2 Touch [Bluetooth Connection], then touch
[ON].
Make sure that lights up on the status bar of
the unit.
3 Activate the BLUETOOTH function on the
BLUETOOTH device.
4 Operate the BLUETOOTH device to connect
to this unit.
or lights up on the status bar.
To connect the last-connected device from
this unit
When the ignition is turned to on with the
BLUETOOTH signal activated, this unit searches for
the last-connected BLUETOOTH device, and
connection is made automatically.
If it does not work, touch [Reconnect] to search for
the last-paired device again. If the problem is not
solved, follow the pairing procedure.
Note
While streaming BLUETOOTH audio, you cannot connect
from this unit to the cellular phone. Connect from the
cellular phone to this unit instead.
To install the microphone
For details, see “Installing the microphone (XAVW651BT/XAV-V631BT)” (page 34).
Connecting a USB Device
1 Turn down the volume on the unit.
2 Connect the USB device to the unit.
To connect an iPod/iPhone, use the USB
connection cable for iPod (not supplied).
Connecting Other Portable Audio/Video Devices
1 Turn off the portable audio/video device.
2 Turn down the volume on the unit.
3 Connect the portable audio/video device to
the AUX input jack on the unit with a
connecting cord (not supplied).
4 Press HOME, then touch [AUX].
To match the volume level of the connected
device to other sources
Start playback of the portable audio/video device
at a moderate volume and set your usual listening
volume on the unit:
Touch , then set [Input Level] between –10 and
+15.
To set to the device type manually
Touch , then set [AUX Input] to [Audio], [Video],
or [Auto].
Connecting Rear View Camera
By connecting the optional rear view camera to the
CAMERA IN terminal, you can display the picture
from the rear view camera. For details, see
“Connection/Installation” (page 31).
9GB
Listening to the Radio
Listening to the Radio
To listen to the radio, press HOME then touch
[Tuner].
Reception controls/indications
Current band
Opens the band list.
Current frequency, program service name*,
RDS indication*
* During RDS reception.
PTY (program types) (FM only)
Opens the PTY list (page 11).
ZAP (ZAPPIN)
Helps to find a desired station by listening to
preset stations for a few seconds.
(option)
Opens the option menu.
–SEEK/SEEK+
Tunes in automatically.
/
Tunes in manually.
Touch and hold to continuously skip
frequencies.
Preset numbers (1 to 6)
Selects a preset station.
Touch and hold to store the current frequency in
that preset.
Storing automatically (BTM)
1 Select the desired band (FM1, FM2, FM3,
AM1, or AM2).
2 Touch .
3 Touch [BTM], then [Search].
The unit stores stations in order of frequency on
the preset numbers (1 to 6).
Tuning
1 Touch the current band.
The band list appears.
2 Touch the desired band (FM1, FM2, FM3,
AM1, or AM2).
3 Perform tuning.
To t u ne aut o mat i ca lly
Touch –SEEK/SEEK+.
Scanning stops when the unit receives a station.
To tune manually
Touc h and hol d / to locate the approximate
frequency, then touch / repeatedly to fine
adjust to the desired frequency.
Storing manually
1 While receiving the station that you want to
store, press and hold the desired preset
number (1 to 6).
Receiving stored stations
1 Select the band, then touch the desired
preset number (1 to 6).
Searching for the desired station from
preset stations (Tuner Preset ZAPPIN)
Tuner Preset ZAPPIN helps you to find a desired
station by listening to preset stations for a few
seconds.
1 During radio reception, touch [ZAP].
Tuner Preset ZAPPIN starts, and subsequent
stations are received in sequence.
2 Touch [ZAP] again when the desired station
is received.
10GB
Using Radio Data System (RDS)
Playback
Selecting program types (PTY)
1 During FM reception, touch [PTY].
To scroll the list, touch /.
2 Touch the desired program type.
The unit searches for a station broadcasting the
selected program type.
To close the PTY list
Touch .
Type of programs
News (News), Current Affairs (Current Affairs),
Information (Information), Sport (Sports), Education
(Education), Drama (Drama), Cultures (Culture),
Science (Science), Varied Speech (Varied), Pop Music
(Pop Music), Rock Music (Rock Music), Easy Listening
(M.O.R. Music), Light Classics M (Light classical),
Serious Classics (Serious classical), Other Music (Other
Music), Wea th er & M etr (Weather), Finance (Finance),
Children’s Progs (Children’s program), Social Affairs
(Social Affairs), Religion (Religion), Phone In (Phone
In), Trave l & Tou ri ng (Travel), Leisure & Hobby
(Leisure), Jazz Music (Jazz Music), Country Music
(Country Music), National Music (National Music),
Oldies Music (Oldies Music), Folk Music (Folk Music),
Documentary (Documen tary)
Setting clock time (CT)
The CT data from the RDS transmission sets the
clock.
1 Set [Clock Time] to [ON] in [General Settings]
(page 18).
Playing a Disc (XAV-W651BT/ XAV-W601)
Depending on the disc type, some operations may
be different or restricted.
1 Insert the disc (label side up).
Playback starts automatically.
If a DVD menu appears
Touch the desired item in the DVD menu.
You can also use the menu control panel, which can
be displayed by touching the screen anywhere
except the DVD menu items. Touch /// to
move the cursor, then touch [ENTER] to confirm.
If the menu control panel does not appear by
touching the display, use the remote commander.
Example of playback indications (DVD)
Current source icon, format
Playback status, elapsed playback time
Chapter/title number, audio format
Touch the display if the indications are not
displayed.
For audio discs, some indications are always
displayed during playback.
11GB
Loading...