Sony XAVV750BT User Manual

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\010COV.fm

010book.book Page 1 Tuesday, November 24, 2015 9:51 AM

masterpage: Cover

4-573-332-11(1)

AV Center

Operating Instructions

Manual de instrucciones

To cancel the demonstration (Demo) display, see page 19.

For the connection/installation, see page 28.

Para cancelar la pantalla de demostración (Demostración), consulte la página 19.

Para la conexión/instalación, consulte la página 29.

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GB-

(For Singapore models only)

XAVV750BTE17\020INT.fm

010book.book Page 2 Tuesday, November 24, 2015 9:51 AM

masterpage: Left

For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. For details, see “Connection/Installation” (page 28).

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.

Warning

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems)

Note on the lithium battery

Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Warning if your car’s ignition has no ACC position

After turning the ignition off, be sure to press and hold HOME on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain.

Disclaimer regarding services offered by third parties

Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

This device complies with Part 15 of the FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including Interference that may cause undesired operation of the device.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

2GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\020INT.fm

010book.book Page 3 Tuesday, November 24, 2015 9:51 AM

Important notice

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH device

may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident.  where inflammable gas is present, in a hospital,

train, airplane, or petrol station

 near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.

 We do not take any responsibility for the leakage

of information during BLUETOOTH communication.

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

masterpage: Right

3GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\030TOC.fm

010book.book Page 4 Tuesday, November 24, 2015 9:51 AM

masterpage: Left

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5

Getting Started

Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Performing Initial Settings . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device. . . . . . . . . . . . . . . . 8

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . . 9

Connecting Other Portable Audio/

Video Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Rear View Camera . . . . . . . . . . . . . . . . 9

Listening to the Radio

Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . 10

Using Radio Data System (RDS) . . . . . . . . . . . . . . . 11

Playback

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 11

Playing a BLUETOOTH Device. . . . . . . . . . . . . . . . . 12

Searching and Playing Tracks. . . . . . . . . . . . . . . . . 12

Other Settings During Playback. . . . . . . . . . . . . . . 13

Handsfree Calling (via BLUETOOTH only)

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Available Operations During a Call . . . . . . . . . . . . 14

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 28

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Useful Functions

SongPal with Android Smartphone . . . . . . . . . . . . 15

Using Siri Eyes Free . . . . . . . . . . . . . . . . . . . . . . . . . 16

Settings

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 17

General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Visual Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 5 Tuesday, November 24, 2015 9:51 AM

Guide to Parts and Controls

Main unit

masterpage: Right

The VOLUME + button has a tactile dot.

 Display/touch panel  HOME

Turn on the power. Open the HOME menu. Press to pause playback when the iPod/USB source is selected. To resume playback, touch . Press and hold for more than 2 seconds to turn off the unit. When the unit is turned off, remote commander operation is not available.

ATT (attenuate)

Press and hold for 1 second (less than 2 seconds) to attenuate the sound. To cancel, press and hold again, or press VOLUME +.

 Reset button  N-Mark

Make Bluetooth® connection when touched with Android™ smartphone.

 Receptor for the remote commander  VOLUME +/–

 SOURCE

Change the source. To turn the source off, press repeatedly to select [OFF].

VOICE

Press and hold to activate the voice command function. To assign the DSPL function to this button, select [DSPL] in [SOURCE Key Func.] (page 18).

DSPL (display)

Press and hold to open the display menu. The monitor off function can be set on the display menu. When the monitor off function is activated and the monitor is turned off, touch anywhere on the display to turn it back on.

5GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 6 Tuesday, November 24, 2015 9:51 AM

masterpage: Left

RM-X170 remote commander

The remote commander can be used to operate the audio controls. For menu operations, use the touch panel.

 OFF

Turn th e so urce of f. Press and hold for 2 seconds to turn off the power and display.

 MONITOR OFF

Turn off the monitor and button illumination. To turn back on, press again.

 POSITION

This button is not supported.

 (return)

Return to the previous display.

 EQ (equalizer)

Select an equalizer curve.

 Number buttons (0 – 9)  CLEAR  (play/pause)

/ (previous/next) / (fast-reverse/fast-forward)

 DVD playback setting buttons

These buttons are not supported.

 ZAP (ZAPPIN™) (page 10)

///

Select a setup item, etc.

ENTER

Enter the selected item.

 MODE

Select the radio band.

Remove the insulation film before use.

Screen displays

Playback screen:

Home screen:

6GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 7 Tuesday, November 24, 2015 9:51 AM

 Status indication

Lights up when the sound is attenuated.

Lights up when the “SongPal” connection is established between this unit and your Android smartphone.

Lights up when the BLUETOOTH signal is on. Flashes when the connection is in progress.

Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile).

Lights up when handsfree calling is available by enabling the HFP (Handsfree Profile).

Indicates the signal strength status of the connected cellular phone.

Indicates the remaining battery status of the connected cellular phone.

 (Mega Bass)

Touch to select the Mega Bass setting: [1], [2], [Off].

(sound setting menu)

Access the sound setting menu directly (page 18).

(option)

Open the option menu. The available items differ depending on the source.

 Clock (page 7)

When the AUX or Rear Camera source is selected, the clock is not displayed.

 Application specific area

Display playback controls/indications or show the unit’s status. Displayed items differ depending on the source.

 (return to the playback screen)

Switch from the HOME screen to the playback screen.

 (option)

Open the option menu. The available items differ depending on the source.

 Sources and Settings select keys

Change the source or make various settings.

Getting Started

Resetting the Unit

You must reset the unit before operating the unit for the first time, after replacing the car battery, or changing connections.

Note

Pressing the reset button will erase the clock setting and some stored contents.

Performing Initial Settings

After resetting, the initial setting display appears.

1 Touch [Language], then set the display

language.

2 Touch [Output Color System], then set

the color system.

3 Touch [Tuner Step], then set the FM/AM

tuning step.

4 After setting the FM/AM tuning step,

touch [OK].

The startup caution appears.

5 Touch [OK].

The setting is complete.

This setting can be further configured in the setting menu (page 17).

Setting the Clock

1 Press HOME, then touch [Settings]. 2 Touch , then touch [Clock Adjust].

The setting display appears.

3 Touch / to set the hour and minute. 4 After setting the hour and minute, touch

[Set].

The setting is complete and the clock starts.

masterpage: Right

7GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GB-

[0000]

Input passkey

XAVV750BTE17\040CD.fm

010book.book Page 8 Tuesday, November 24, 2015 9:51 AM

In this case, disconnect the other device, and make a

Preparing a BLUETOOTH Device

You can enjoy music or perform handsfree calling depending on the BLUETOOTH compatible device such as smartphones, cellular phones, and audio devices (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device. Before connecting the device, turn down the volume of this unit; otherwise, a loud sound may result.

connection with the smartphone again.

Pairing and connecting with a BLUETOOTH device

When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

Connecting with a smartphone by One touch (NFC)

By touching the N-Mark on the unit with an NFC* compatible smartphone, the unit is paired and connected with the smartphone automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication between various devices, such as mobile phones and IC tags. Thanks to the NFC function, data communication can be achieved easily just by touching the relevant symbol or designated location on NFC compatible devi ces.

For a smartphone with Android OS 4.0 or lower installed, downloading of the app “NFC Easy Connect” available at Google Play™ is required. The app may not be downloadable in some countries/ regions.

1 Activate the NFC function on the

smartphone.

For details, refer to the operating instructions supplied with the smartphone.

1 Place the BLUETOOTH device within 1 m

(3 ft) of this unit.

2 Press HOME, then touch [Settings]. 3 Touch . 4 Touch [Bluetooth Connection], then set

the signal to [ON].

The BLUETOOTH signal is turned on and lights up on the status bar of the unit.

5 Touch [Pairing].

flashes while the unit is in pairing standby

mode.

6 Perform pairing on the BLUETOOTH

device so it detects this unit.

7 Select [XAV-V750BT] shown in the

display of the BLUETOOTH device.

If your model name does not appear, repeat from step 5.

2 Touch the N-Mark part of the unit with

the N-Mark part of the smartphone.

masterpage: Left

Make sure that lights up on the status bar of the unit.

To disconnect by One touch

Touch the N-Mark part of the unit with the N-Mark part of the smartphone again.

Notes

 When making the connection, handle the

smartphone carefully to prevent scratches.

 One touch connection is not possible when the unit is

already connected to another NFC compatible device.

8GB

8 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “passcode,” “PIN code,”

“PIN number,” “password,” etc., depending on the BLUETOOTH device.

When pairing is made, stays lit.

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 9 Tuesday, November 24, 2015 9:51 AM

9 Select this unit on the BLUETOOTH device

to establish the BLUETOOTH connection.

or lights up when the connection is made.

Note

While connecting to a BLUETOOTH device, this unit cannot be detected by another device. To enable detection, enter the pairing mode and search for this unit from another device.

To start playback

For details, see “Playing a BLUETOOTH Device” (page 12).

To cancel pair ing

Perform step 5 to cancel the pairing mode after this unit and the BLUETOOTH devices are paired.

Connecting a USB Device

1 Turn down the volume on the unit. 2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied).

Connecting Other Portable Audio/Video Devices

1 Turn off the portable audio/video device. 2 Turn down the volume on the unit.

Connecting with a paired BLUETOOTH device

To use a paired device, connection with this unit is required. Some paired devices will connect automatically.

1 Press HOME, then touch [Settings]. 2 Touch [Bluetooth Connection], then

touch [ON].

Make sure that lights up on the status bar of the unit.

3 Connect the portable audio/video device

to the AUX input jack on the unit with a connecting cord (not supplied).

4 Press HOME, then touch [AUX].

To match the volume level of the connected device to other sources

Start playback of the portable audio/video device at a moderate volume and set your usual listening volume on the unit: Touch , then set [Input Level] between –10 and +15.

To set to the device type manually

Touch , then set [AUX Input] to [Audio], [Video], or [Auto].

3 Activate the BLUETOOTH function on the

BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up on the status bar.

To connect the last-connected device from this unit

When the ignition is turned to on with the BLUETOOTH signal activated, this unit searches for the last-connected BLUETOOTH device, and connection is made automatically. If it does not work, touch [Reconnect] to search for the last-paired device again. If the problem is not solved, follow the pairing procedure.

Note

While streaming BLUETOOTH audio, you cannot connect from this unit to the cellular phone. Connect from the cellular phone to this unit instead.

To install the microphone

For details, see “Installing the microphone” (page 31).

Connecting Rear View Camera

By connecting the optional rear view camera to the CAMERA IN terminal, you can display the picture from the rear view camera. For details, see “Connection/Installation” (page 28).

masterpage: Right

9GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 10 Tuesday, November 24, 2015 9:51 AM

Storing automatically (BTM)

Listening to the Radio

To listen to the radio, press HOME then touch [Tuner].

Reception controls/indications

1 Select the desired band (FM1, FM2, FM3,

AM1, or AM2).

2 Touch . 3 Touch [BTM], then [Search].

The unit stores stations in order of frequency on the preset numbers (1 to 6).

Tuning

1 Touch the current band.

The band list appears.

2 Touch the desired band (FM1, FM2, FM3,

AM1, or AM2).

3 Perform tuning.

To tune automatically

Touch –SEEK/SEEK+. Scanning stops when the unit receives a station.

 Current band

Opens the band list.

 Current frequency, program service name*,

RDS indication*

* During RDS reception.

 PTY (program types) (FM only)

Opens the PTY list (page 11).

 ZAP (ZAPPIN)

Helps to find a desired station by listening to preset stations for a few seconds.

 (option)

Opens the option menu.

 –SEEK/SEEK+

Tunes in automatically.

/

Tunes in manually. Touch and hold to continuously skip frequencies.

 Preset numbers (1 to 6)

Selects a preset station. Touch and hold to store the current frequency in that preset.

To tune manually

Touch and hold / to locate the approximate frequency, then touch / repeatedly to fine adjust to the desired frequency.

Storing manually

1 While receiving the station that you want

to store, press and hold the desired preset number (1 to 6).

Receiving stored stations

1 Select the band, then touch the desired

preset number (1 to 6).

Searching for the desired station from preset stations (Tuner Preset ZAPPIN)

Tuner Preset ZAPPIN helps you to find a desired station by listening to preset stations for a few seconds.

1 During radio reception, touch [ZAP].

Tuner Preset ZAPPIN starts, and subsequent stations are received in sequence.

2 Touch [ZAP] again when the desired

station is received.

masterpage: Left

10GB

XAV-V750BT

4-573-332-11(1)

F:\#Work#\Y3\eV\Harrier 7\Sagyo data\4573332111\4573332111XAVV750BTE17\01GBXAVV750BTE17\040CD.fm

010book.book Page 11 Tuesday, November 24, 2015 9:51 AM

masterpage: Right

Using Radio Data System (RDS)

Selecting program types (PTY)

1 During FM reception, touch [PTY].

To scroll the list, touch /.

2 Touch the desired program type.

The unit searches for a station broadcasting the selected program type.

To close the PTY list

Touch .

Typ e of p rograms

News (News), Current Affairs (Current Affairs), Information (Information), Sport (Sports), Education (Education), Drama (Drama), Cultures

(Culture), Science (Science), Varied Speech (Varied), Pop Music (Pop Music), Rock Music (Rock Music), Easy Listening (M.O.R. Music), Light Classics M (Light classical), Serious Classics (Serious classical), Other Music (Other Music),

Weather & Metr (Weather), Finance (Finance), Children’s Progs (Children’s program), Social Affairs (Social Affairs), Religion (Religion), Phone In (Phone In), Travel & Tou rin g (Travel), Leisure & Hobby (Leisure), Jazz Music (Jazz Music), Country Music (Country Music), National Music (National

Music), Oldies Music (Oldies Music), Folk Music (Folk Music), Documentary (Documentary)

Setting clock time (CT)

The CT data from the RDS transmission sets the clock.

1 Set [Clock Time] to [ON] in [General

Settings] (page 17).

Playback

Playing a USB Device

In these Operating Instructions, “iPod” is used as a general reference for the iPod functions on the iPod and iPhone, unless otherwise specified by the text or illustrations.

For details on the compatibility of your iPod, see “About iPod” (page 21) or visit the support site on the back cover.

MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices (such as a USB flash drive, digital media player, Android smartphone) compliant with the USB standard can be used. Depending on the digital media player or Android smartphone, setting the USB connection mode to MTP is required.

Notes

 For details on the compatibility of your USB device,

visit the support site on the back cover.

 Playback of the following files is not supported.

MP3/WMA/AAC/FLAC:

 copyright-protected files  DRM (Digital Rights Management) files  Multi-channel audio files

MP3/WMA/AAC:  lossless compression files WAV:  Multi-channel audio files

1 Connect the USB device to the USB port.

Playback starts. If a device is already connected, press HOME then touch [iPod/USB] to start playback.

2 Adjust the volume on this unit.

To stop playback

Press OFF, or press SOURCE repeatedly until [OFF] appears.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB, the phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as a sudden loud sound may result when the call ends.

11GB

XAV-V750BT

4-573-332-11(1)

+ 23 hidden pages