Sony XAV-701HD User Manual
TomTom navigation
module
What’s in the box1.
What’s
in the
box • TomTom navigation module
• Car dock
•USB cable
•MyTomTom leaflet
2
Read me first2.
Read me first
Car dock
Push your TomTom navigation module into the car dock in your car. To remove your navigation module from the car dock, press the release button on the car dock. Your dealer
can install the car dock and connect it to the Sony XNV.
The display of the Sony XNV is also used as the navigation module display. Use the Sony
XNV touch screen to operate your navigation module.
Switching on and off
The TomTom navigation module switches on simultaneously with the Sony XNV. Select
Navi in the main menu of the Sony XNV.
Until a connection has been established between the Sony XNV and the navigation module, "waiting for Navi connection" is displayed. In the case of a cold boot of the navigation
module, the start-up image of the module is visible as soon as a connection has been
established.
Under extreme temperature conditions or if the battery of the navigation module is empty,
a warning screen will be displayed. The module will start up as soon as the battery temperature is within specifications and the battery is charged sufficiently.
Setting up
Important: Take care to select the correct language, since the language you choose will
be used for all menus and written instructions.
When you first switch on your device, you have to answer a few questions to set up the
device. Answer the questions by tapping the screen.
GPS reception
When you first start your TomTom navigation module, the device may need a few minutes
to determine your GPS position and show your current position on the map. In the future,
your position will be found much faster, usually within a few seconds.
To ensure good GPS reception, you should use your device outdoors. Large objects such
as tall buildings can sometimes interfere with reception.
About MyTomTom
MyTomTom helps you manage the contents and services of your TomTom navigation
module, as well as giving you access to the TomTom community. You log in to MyTomTom on the TomTom website. It is a good idea to frequently connect your navigation module to MyTomTom, to ensure you always have the latest updates.
3
Tip: We recommend using a broadband internet connection whenever you connect your
navigation device to MyTomTom.
Setting up MyTomTom
1
1
1
2
2
2
To set up MyTomTom, do the following:
1. Connect your computer to the internet.
2. Start a browser and go to tomtom.com/getstarted.
3. Click Download now.
Your browser downloads the MyTomTom support application, which you need to
install on your computer in order to connect your device to MyTomTom. Follow the
instructions on the screen if you are asked questions while downloading.
4. Connect your device to your computer using the USB cable.
Your device is then recognized, and possible updates are offered.
Important: You should plug the USB connector directly into a USB port on your computer
and not into a USB hub or USB port on a keyboard or monitor.
Once the MyTomTom support application is installed on your computer, you can access
MyTomTom from the system tray on your computer.
Tip: When you connect your navigation device to your computer, MyTomTom tells you if
there are any updates for your device.
Device not starting
In rare cases, your TomTom navigation module may not start correctly or may stop
responding to your taps.
The battery may not be charged enough. The battery charges when the navigation module
is docked in the car dock and the Sony XNV is powered, or when the module is connected
to the computer. The screen shows a warning if there is a problem with the battery.
The battery temperature may be too high or too low. Also in this case the screen shows a
warning. The navigation module will start-up if the battery temperature is within the specifications.
If the battery is charged but navigation is still not available, you may need to reset the navigation module. To reset your navigation module, first remove it from the car dock by
pressing the release button. Then press the reset button on the back of the navigation
module for at least 10 seconds. Push the navigation module back into the car dock.
4
Charging your TomTom navigation module
The LED on the navigation module is red while the battery is charging, and is green when
it is fully charged.
Important: You should plug the USB connector directly into a USB port on your computer
and not into a USB hub or USB port on a keyboard or monitor.
Take care of your navigation device
Never leave your TomTom navigation module or accessories on view when you leave the
car as they may become an easy target for thieves.
It is important to take care of your device:
• Your device is not designed for use in extreme temperatures and any such exposure
may cause permanent damage. Extended exposure to sunlight may lead to early deterioration of battery performance.
• Do not open the casing of your device under any circumstances. Doing so may be dangerous and will void the warranty.
5
Safety3.
Safety
Safety settings
We recommend using the safety settings to make your driving as safe as possible.
These are some of the options included in the safety settings:
• Show essential menu buttons while driving
• Show safety reminders
• Warn when driving faster than allowed
6
Planning a route4.
Planning a
route Important: In the interest of safety and to reduce distractions while you are driving, you
should always plan a route before you start driving.
To plan a route on your TomTom navigation module, do the following:
1. Tap the screen to open the Main menu.
2. Tap Navigate to...
3. Tap Address.
Tip: The first time you plan a route, you are asked to select a country, state or region. Your
selection is saved and used for all future routes until you change this setting.
You can change this setting by tapping the flag before you select a city.
4. Enter the town or city name.
• Towns with similar names are shown in the list while you type.
• When the correct city or town appears in the list, tap the name to select the destina-
tion.
5. Enter the street name.
• Streets with similar names are shown in the list while you type.
7
• When the correct street name appears in the list, tap the name to select the destina-
tion.
6. Enter the house number, then tap Done.
7. The location is shown on the map. Tap Select to continue or tap Back to enter another
address.
Tip: If you want your final destination to be a car park, tap Parking facility and select a
location from the list of car parks close to your general destination.
8. Select the type of route you want to plan.
8
9. When the new route is shown, tap Done.
• For more information about the route, tap Details.
• To plan a different route, tap Change route.
Your TomTom navigation module starts to guide you to your destination, using spoken
instructions and on-screen directions.
Route summary
The route summary shows an overview of your route, the remaining distance to your destination and the remaining estimated trip time.
To view the route summary, tap the right-hand panel on the status bar in the Driving view
or tap View route in the Main menu and then tap Show route summary.
The route summary screen shows an overview of your route, the remaining distance to
your destination, the remaining estimated journey time, and expected delays on your
route using IQ Routes information about actual speeds on roads.
Frequent destinations
If you often make trips to the same destinations, you can set your TomTom navigation
module to ask if you want to plan a route to one of these locations, every time the device
starts. This is faster than planning a route in the normal way.
To select a new destination, tap Start-up settings in the Settings menu and select Ask for
a destination. Then select a button to use for this destination and answer the questions
about the destination.
9
Show my frequent destinations
You can set your TomTom navigation module to ask if you want to plan a route to one of
your frequently visited destinations every time the device starts.
To change this setting, do the following:
1. Tap Start-up settings in the Settings menu and then select Ask for a destination.
2. Tap Yes, then tap Yes again to begin entering information about the destination.
3. Select a symbol for the destination and tap Done to set the symbol, then tap Yes.
Tip: To add new destinations, select one of the numbered symbols and enter a name for
the new destination button.
4. Tap Yes and if required enter a new name, then tap Done.
5. Enter the address details in the same way you enter an address when planning a route,
then tap Done.
6. If you want to set more destinations, repeat the steps above. Otherwise, tap Done.
You are asked if you want to change the start-up image.
7. If you want to change the image, tap Yes, then follow the instructions shown on the
screen. Otherwise, tap No.
Every time your TomTom navigation module starts, you are asked if you want to plan a
route. If you tap Cancel, you are shown the Main Menu.
Using arrival times
When you plan a route, your TomTom navigation module asks you if you need to arrive
at a particular time.
Tap YES to enter a preferred arrival time.
Your navigation module calculates your arrival time and shows you whether you will
arrive on time.
You can also use this information to work out when you need to leave. If your navigation
module shows that you will arrive 30 minutes early, you can wait and leave in 30 minutes
time, rather than arrive early.
Your arrival time is constantly recalculated during your trip. The status bar shows whether
you will arrive on time or if you are going to be late, as shown below:
You will arrive 55 minutes before the arrival time you entered.
If the estimated arrival time is more than five minutes before the time
you entered, it is shown in green.
10
You will arrive 3 minutes before the arrival time you entered.
If the estimated arrival time is less than 5 minutes before the time
you entered, it is shown in yellow.
You will arrive 19 minutes late.
If the estimated arrival time is later than the time you entered, it is
shown in red.
Ta p Status bar settings in the Settings menu, to enable or disable
arrival time notifications.
Status bar
preferences
To enable arrival time notifications, select Leeway.
Navigation menu options
When you tap Navigate to..., you can set your destination in many ways, not just by entering the address. The other options are listed below:
Tap this button to navigate to your Home location.
You will probably use this button more than any other.
Home
Tap this button to select a Favorite as your destination.
Favorite
Tap this button to enter an address as your destination.
Address
Tap this button to select your destination from a list of places you
have recently used as destinations.
Recent
destination
Point of Interest
Point on map
Latitude
Longitude
Tap this button to navigate to a Point of Interest (POI).
Tap this button to select a point on the map as your destination using
the map browser.
Tap this button to enter a destination using latitude and longitude
values.
11
Tap this button to select your last recorded position, as your destination.
Position of last
stop
Planning a route in advance
You can use your TomTom navigation module to plan a route in advance, selecting your
starting point and your destination.
Here are some more reasons to plan a route in advance:
• Find out how long a trip is going to take before you start.
You can also compare trip times for the same route at different times of the day or on
different days of the week. Your navigation module uses IQ Routes when planning a
route. IQ Routes calculates routes based on the real average speeds measured on
roads.
• Study the route of a trip you are planning.
• Check a route for someone who is coming to visit you and then explain the route to
them in detail.
To plan a route in advance, follow these steps:
1. Tap the screen to bring up the Main menu.
2. Tap Plan route.
This button is shown while there is no planned route on your navigation module.
Prepare route
3. Select the starting point for your trip in the same way that you would select your destination.
4. Set the destination for your trip.
5. Choose the type of route that should be planned.
• Fastest route - the route which takes the least time.
• Eco route - the most fuel-efficient route for your trip.
• Shortest route - the shortest distance between the locations you set. This may not
be the quickest route, especially if the shortest route is through a town or city.
• Avoid highways - a route which avoids highways.
6. Choose the date and time that you will make the trip you are planning.
Your navigation module uses IQ Routes to work out the best possible route at that time.
This is useful to see how long a trip takes at different times of the day or on different
days of the week.
7. Your TomTom navigation module plans the route between the two locations you
selected.
Viewing route information
You can access these options for the route you last planned by tapping View route in the
Main Menu or the Details button on the route summary screen.
12
You can then select from the following options:
Tap this button for a list of all the turn instructions on the route.
This is very useful if you need to explain a route to someone else.
Show instruc-
tions
Tap this button to see an overview of the route using the map
browser.
Show map of
route
Tap this button to watch a demo of the trip. You can interrupt the
demo at any time by tapping the screen.
Show route
demo
Tap this button to open the route summary screen.
Show route
summary
Tap this button to see a preview of your destination.
Show
destination
You can navigate to a parking lot near your destination, and view any
available information about your destination, for example, the phone
number.
13
Driving View5.
Driving View
About the Driving View
When your TomTom navigation module device starts for the first time, you are shown the
Driving View along with detailed information about your current position.
Tap the center of the screen at any time to open the Main Menu.
You can choose the screen shown when you switch on your device by tapping Settings
in the Main Menu, then tapping Start-up settings.
The Driving View
1. Zoom button - tap the magnifying glass to show buttons for zooming in and out.
2. Quick menu - to enable the quick menu, tap Make your own menu in the Settings menu.
3. Your current position.
4. Road sign information or the next street name.
5. The time, your current speed and the speed limit, if known. To see the difference
between your preferred arrival time and your estimated arrival time, check the Leeway
checkbox in the Status bar settings.
Tap this part of the status bar to switch between a 3D map and a 2D map.
6. The name of the street you are on.
7. Navigation instruction for the road ahead and the distance to next instruction. If the second instruction is less than 500 feet after the first instruction, you see it shown immediately instead of the distance.
Tap this part of the status bar to repeat the last voice instruction and to change the volume. You can also tap here to mute the sound.
8. The remaining trip time, the remaining distance and your estimated arrival time.
14
Tap this part of the status bar to open the Route Summary screen.
To change the information shown in the status bar, tap Status bar in the Settings menu.
Driving View symbols
The following symbols are shown in the Driving View:
EPT - this symbol is shown when your device is using tacho information to estimate your current location. EPT is only used when you
have no GPS reception.
Sound muted - this symbol is shown when the sound has been
muted.
To turn the sound back on, tap the middle panel in the status bar.
15
Advanced Lane Guidance6.
Advanc
ed
Lane
About lane guidance
Guidance
Note: Lane guidance is not available for all junctions or in all countries.
Your TomTom navigation module helps you prepare for highway exits and junctions by
showing the correct driving lane for your planned route.
As you approach an exit or junction, the lane you need is shown on the screen.
Using lane guidance
There are two types of lane guidance:
• Lane images
To turn lane images off, tap Settings in the Main Menu, then tap Advanced settings.
Clear the checkbox for Show lane images.
Tip: Tap anywhere on the screen to return to the Driving View.
• Instructions in the status bar
16
Tip: If no lane guidance is shown in the status bar and all lanes are highlighted, you can
use any lane.
17
Making changes to your route7.
Making
change
About route changes
s to
your
route
After you plan a route, you may want to change the route or even the destination. There
are various ways to change your route without the need to completely replan the entire
trip.
To change the current route, tap Change route in the Main menu:
Tap this button to change the current route.
This button is only shown while there is a planned route on your
Change route
Change route menu
To change the current route or your destination, tap one of the following buttons:
Calculate
alternative
navigation module.
Tap this button to find an alternative to the current route.
This button is only shown while there is a planned route on your
navigation module.
This is a simple way to search for a different route to your current
destination.
Avoid roadblock
Your navigation module calculates a new route from your current
location to reach your destination using completely different roads.
The new route is shown next to the original route so that you can
select the route you want to use.
Tap this button while driving on a planned route to avoid a roadblock
or traffic congestion on the road ahead.
Your navigation module will suggest a new route which avoids the
roads on your current route for the selected distance.
If the roadblock or traffic congestion suddenly clears, tap Recalcu-
late route to replan your original route.
Important: Be aware that when a new route is calculated, you might
be asked to turn off the current road immediately.
18
Change
destination
Avoid part of
route
Tap this button to change the current destination.
When you change the destination, you are shown the same options
and asked to enter the new address in the same way as when you
plan a new route.
Tap this button to avoid part of the current route.
You are shown a list of the street names on your route. When you
tap one of the street names, your navigation module calculates a
detour to avoid the selected street. The route summary shows both
the new route and your original route. Tap the panel at the right to
select one of the routes and then tap Done.
If you do not want to use either of the routes shown in the route
summary, tap Change route to find another way to alter your route.
Tap this button to change your route by selecting a location you
want to travel past, perhaps to meet someone along the way.
Travel via...
When you select a location to travel past, you are shown the same
options and asked to enter the new address in the same way as
when you plan a new route.
Your navigation module calculates the route to your destination via
the selected location.
The selected location is shown on the map using a marker. You can
only select one location to travel past on a route.
Unlike when you reach your destination, no warning is given when
you travel past a marked location.
19
Loading...