Sony UZ-PS128 User Manual

Page 1
Portable Solid Memory Player
Operating Instructions
4-253-038-31(1)
UZ-PS128
©2004 Sony Corporation
Page 2
WARNING
To prevent fire, do not cover the ventilation of the apparatus with news papers, table cloths, curtains, etc. And don’t place lighted candles on the apparatus.
Certain countries may regulate disposal of the battery used to power this product. Please consult with your local authority.
For the customers in the United States
Owner’s Record
The model number is located on the inner rim of the left ear side of the headphones, and the serial number is located on the inner rim of the right ear side of the headphones. Record the serial number in the space provided below. Refer to them whenever you call your Aiwa dealer regarding this product.
Model No. UZ-PS128 Serial No.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference using one or more of the following measures:
– Reorient or relocate the receiving antenna. – Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
If you have any questions about this product, you may call; Aiwa Customer Information Service Center 1-800-289-2492 or http://www.us.aiwa.com/.
Declaration of Conformity
Trade Name: AIWA Model: UZ-PS128 Responsible Party: Sony Electronics Inc. Address: 680 Kinderkamack Road,
Telephone Number: 201-930-6973 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Oradell, NJ 07649 U.S.A.
Before using this player, install the application software on your computer using the supplied CD-ROM, and send some music data to the player.
2
Page 3
Table of Contents
Overview
What you can do with your player ............. 4
Main features .............................................. 5
Getting started
Step 1: Check the package contents ........... 6
Step 2: Insert a battery ................................ 7
Locating controls ........................................ 8
Basic operations
Listening to music stored in your player .... 9
1. Put the player on your ears. .................... 9
2. Start playback. ...................................... 10
Recording from another audio device ...... 12
Erasing tracks one by one......................... 13
B
Advanced operations
Changing the sound quality (M.D.S.E) .... 14
Playing a track repeatedly
(Repeat Play) ........................................ 14
Using the player as stereo headphones ..... 15
B
Additional information
Precautions ............................................... 16
Cleaning.................................................... 16
Troubleshooting ........................................ 17
Specifications ........................................... 18
Index ......................................................... 19
3
Page 4

Overview

What you can do with your player

Your UZ-PS128 is a portable player with built-in solid memory. You can play back MP3 files transferred to the player from your personal computer using the supplied software and the dedicated USB cable. You can also record and listen to the sound from another audio device connected to the player with the supplied analog connection cord. Once you have stored your favorite songs in the player, take it with you and enjoy music wherever you go!
1 Record music
to your player.
There are two ways to store audio data into your player’s built-in memory:
• Transfer audio data (MP3 files) from your computer, using the supplied software “Music Transfer Solid Memory Edition.”
See the separate manual for the Music Transfer software for details.
• Record from another audio device.
See page 12 for details.
2 Enjoy music
anywhere with your player!
4
Page 5

Main features

• Headphone-style solid memory player
- Highly portable with the player built into the headphones
- Skip-proof using flash memory
•Approximately 11 hours of continuous playback with a single LR03 (size AAA) alkaline battery
• Up to 120 minutes* of music can be stored in the built-in memory.
• MP3 files on your computer are transferred to the player by simple and easy opera tions using the supplied software and the dedicated USB cable.
•You can connect another audio device to the player and record the sound from the connected device in MP3 format while listening to the sound.
*The time length varies according to the bit rate used when encoding MP3 files. The time indicated here is for
128-kbps MP3 files.
Notes
• Music you record is limited to private use only. Any other use requires the permission of the copyright
holders.
• Sony is not liable for failure in recording and damage to or erasure of recorded contents caused by
incomplete data transfer or data destruction due to problems with this product or your computer.
• Always make a trial recording before performing important recording.
OverviewOverview
5
Page 6

Getting started

Step 1: Check the package contents

Check the accessories enclosed in the package.
• Portable solid memory player (1)
• Dedicated USB cable (1)
• Analog connection cord (1)
• CD-ROM* (“Music Transfer Solid Memory Edition”) (1)
• Operating instructions for the application software “Music Transfer Solid Memory Edition” (1)
• Quick start guide (1)
About the serial number
The serial number provided for your player is printed on the inner rim of the right ear side of the headphones.
* Do not play the CD-ROM on an audio CD player.
6
Page 7

Step 2: Insert a battery

The battery compartment is provided on the left ear side. Insert one LR03 (size AAA) alkaline battery into the battery compartment as illustrated below.
Insert with the e
e
side upward
E
Battery duration
Approximately 11 hours (continuous playback, with a Sony LR03 (size AAA) alkaline battery)
When to replace the battery
When the battery power becomes low, playback stops, the OPE indicator flashes red for about 10 seconds, and then the power is turned off automatically. Replace the battery with a new one.
Notes on dry batteries
• Do not throw batteries into fire.
• Do not carry batteries with coins or other metallic objects. It can generate heat if the positive and negative terminals of the battery are accidentally contacted by a metallic object.
•When the player is not to be used for a long time, remove the battery.
• If battery leakage occurs, wipe off any deposit in the battery compartment, and insert a new battery. In case the deposit adheres to you, wash it off thoroughly.
Getting started
7
Page 8

Locating controls

Player (right ear side)
12
34
5
1 (repeat)/AUTO TRA CK switch 2 M.D.S.E switch 3 POWER switch 4 OPE indicator 5 ./> (skip/search) buttons
* The button has a tactile dot.
6
8
7
6 PLAY/STOP* button 7 VOL +*/– buttons 8 USB connector 9 INPUT (analog audio input) jack 0 REC/ERASE button
89 0
Page 9

Basic operations

Listening to music stored in your player

First, insert a battery into your player (page 7) and record some audio data to the player’s built-in memory.
Note
Disconnect the player from your computer before listening to music.
1
. Put the player on your ears.
Basic operations
Note
Remove earrings before wearing the player to avoid injury.
(Continued)
9
Page 10
2
. Start playback.
1
POWER OPE
PLAY/STOP
2
1 Set the POWER switch to ON.
The OPE indicator lights up in green.
2 Press PLAY/STOP.
A short beep is heard in the headphones and playback starts.
3 Press VOL +/– to adjust the volume.
During playback, the OPE indicator slowly flashes in green. Playback stops after the last track has been played.
3
VOL +
10
Page 11
Other operations
Basic operations
. >
VOL +
To Do this
Go to the beginning of the next track Press > once.*
1
Go to the beginning of the current track Press . once. Go to the beginning of previous tracks Press . repeatedly.
Press and hold . to quickly locate the track you
2
want.*
Go to the beginning of succeeding tracks Press > repeatedly.*
Press and hold > to quickly locate the track you
2
want.*
1
Adjust the volume Press VOL +/–.
Press and hold VOL +/– to quickly turn up or down
the volume. Stop playback Press PLAY/STOP. Turn off the power Set the POWER switch to OFF.
*1 A short beep sounds for each track. When you press > during the last track or .during the first track,
a long beep sounds.
*2 While holding down the button, a short beep sounds for each track. When the first track is reached, a series
of three short beeps sound and playback starts from the beginning of the first track.
Tip
Playback starts from the position where it was last stopped. To start playback from the first track, press and hold . or > to return to the first track.
11
Page 12

Recording from another audio device

You can connect your player to another audio device, such as a CD player, and record audio from that device. The audio is converted into MP3 files and stored in the player’s internal memory.
Note
The volume and sound quality of the audio from the connected external audio device will affect the recording. Be sure to adjust the volume and turn off sound effects on the external audio device before recording. You can check the playback volume of the external audio device by connecting the player as ordinary stereo headphones with its power turned off (see “Using the player as stereo headphones” on page 15).
POWER OPE
REC/ERASE
INPUT
Analog connection cord (supplied)
Connect another audio device.
1
Connect the supplied analog connection cord to the INPUT (analog audio input) jack of the player and to the headphones jack of the other audio device.
Set the POWER switch to ON to turn on the player.
2
Press REC/ERASE on the player.
3
A short beep sounds in the headphones and the OPE indicator lights up in red.
Start playback on the connected external audio device.
4
Recording starts. While recording, you can listen to the audio of the MP3 files the player has created at a sampling frequency of 44.1 kHz and bit rate of 128 kbps.
Note
While recording from another audio device, do not set the POWER switch to OFF on the player.
to the headphones jack
CD player, cassette recorder, etc.
To stop recording
Press REC/ERASE.
12
Page 13
About recorded tracks
•Whenever you stop recording, the audio recorded up to that point will be stored as a track.
•A new track is recorded after the end of the last track already stored.
• During recording if the player’s memory becomes full, the existing tracks will be erased
starting with the first track.
To separate tracks automatically (Auto T rack)
Set the /AUTO TRACK switch to ON before pressing REC/ERASE in step 3. Recording from the external audio device will automatically be paused when 3 seconds of silence are detected, and all audio recorded to that point will be stored as a track. Recording will start again for another new track when an incoming signal is detected.
Note
Track separation may not be done correctly depending on the condition of the external audio device and the song to be recorded.

Erasing tracks one by one

You can erase tracks while playing, one track at a time.
Play the track you want to erase.
1
Press and hold REC/ERASE.
2
Two short beeps sound in the headphones, and the first 5 seconds of the track are repeated three times while the OPE indicator is flashing in red. Make sure this is the track you want to erase.
Basic operations
If you decide not to erase the track
Press PLAY/STOP. Playback starts normally from the beginning of the track without erasing the track. The track will not be erased either if no buttons are pressed while the first 5 seconds of the track are repeated.
Press REC/ERASE.
3
The OPE indicator flashes quickly in red. When a long beep is heard, the track is erased, the OPE indicator starts flashing in green, and playback starts normally from the next track.
Notes
• Do not turn off the power while erasing a track.
• It takes about 10 seconds to erase a track.
13
Page 14
B

Advanced operations

OFF ON OFF ON
M.D.S.E/AUTO TRA CK
Changing the sound quality
The M.D.S.E (MP3 Digital Sound Enhancer) allows you to enjoy clear digital sound and a resonant bass.
Set the M.D.S.E switch to ON.
Notes
• If the sound is distorted when using the M.D.S.E function, turn down the volume.
• The M.D.S.E function does not work on MP3 files encoded with a bit rate of 320 kbps to ensure their high-quality sound.
To return to the normal sound
Set the M.D.S.E switch to OFF.
(M.D.S.E)
14
Playing a track repeatedly
Set the /AUTO TRACK switch to ON.
After the track has been played 10 times repeatedly, playback stops.
To return to normal play mode
Set the /AUTO TRACK switch to OFF.
(Repeat Play)
Page 15

Using the player as stereo headphones

You can use the player as a pair of ordinary stereo headphones using the supplied analog connection cord.
Set the POWER switch to OFF.
1
Connect the player to another audio device.
2
Connect the supplied analog connection cord to the INPUT jack of the player and to the headphones jack of the other audio device.
Advanced operations
INPUT
Analog connection cord (supplied)
Start playback on the other audio device.
3
Adjust the volume on the connected audio device.
Notes
• If you set the POWER switch to ON, the sound from the connected audio device will not be heard on the player.
•You cannot adjust the volume or change the sound quality on this player while using it as the ordinary headphones.
to the headphones jack CD player,
cassette recorder, etc.
15
Page 16
B

Additional information

Precautions

General
•Never use the player where it will be subjected to extremes of light, temperature, moisture or vibration.
• Remove earrings when using this player to avoid injury.
Road Safety
Do not use this player while driving, cycling, or operating any motorized vehicle. It may create a traffic hazard and is illegal in many areas. It can also be potentially dangerous to play your player at a high volume while walking, especially at pedestrian crossings. You should exercise extreme caution or discontinue use in potentially hazardous situations.
Preventing hearing damage
Avoid using this player at a high volume. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, reduce the volume or discontinue use.
Consideration for others
Keep the volume at a moderate level. This will allow you to hear outside sounds and to be considerate to the people around you.

Cleaning

Clean the player casing with a soft cloth slightly moistened with water or a mild detergent solution.
Note
Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzene as it may mar the finish of the casing.
If you have any questions or problems concerning your player, please consult your nearest Aiwa dealer.
Warning
If there is lightning when you are using your player, take off the player from your ears immediately.
Sony is not liable for any lost or damaged data or program modifications as a result of our repairs.
16
Page 17

Troubleshooting

If you experience any of the following difficulties while using your player, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Aiwa dealer. For trouble concerning operations while connected to your computer, also refer to “Troubleshooting” in the separate manual for the Music Transfer software.
Operation
Symptom There is no sound.
The buttons do not work.
The volume is not loud enough.
The sound is distorted.
Playback stops suddenly.
There is noise in the playback sound.
Cause/Remedy
c The volume level is set to zero.
Turn up the volume (page 11).
c The power is not turned on.
Set the POWER switch to ON.
c There is condensation inside the player.
Let the player sit for a few hours.
c The battery is exhausted.
Replace the battery with a new one (page 7).
c The player is not functioning normally.
Remove the battery to reset the player.
c The volume when recording from another audio device was not
loud enough. Increase the volume on the connected audio device and record again.
c The bit rate used when encoding the MP3 files was low.
Transfer MP3 files encoded with higher bit rates to the player.
c When recording from the external audio device connected to the
player, turn off sound effects on the external audio device.
c The battery is exhausted.
Replace the battery with a new one (page 7).
c The external audio device used for recording was not connected
properly or the plugs were dirty.
c The audio output from the external audio device contained noise. c Noise may have been introduced when creating MP3 files on your
computer due to the conditions of the computer.
Additional information
Battery
Symptom Battery life is short.
Other
Symptom The player gets warm.
Cause/Remedy
c The operating temperature is below 0°C (32°F).
Battery life becomes shorter in cold temperatures due to battery characteristics. This is not a malfunction.
Cause/Remedy
c The player gets warm if it is used for an extended period of time.
This is not a malfunction.
17
Page 18

Specifications

Supported audio file format
MP3 Bit rate: 8 - 320 kbps
Sampling frequencies: 24/22.05/16/32/
44.1/48 kHz MP3 files encoded with a combination of sampling frequency of 22.05 kHz and bit rate of 160 kbps are not playable on this player.
Frequency response
20 - 20,000 Hz (single signal measurement)
Input
INPUT: Stereo mini-jack USB connector
Signal-to-noise ratio (S/N)
70 dB or more (at 128 kbps)
Operating temperature
5ºC - 35ºC (41ºF - 95ºF)
Power output
7 mW + 7 mW
Power source
One LR03 (size AAA) alkaline battery:
1.5 V DC × 1
Battery life
Approx. 11 hours with a Sony LR03 (size AAA) alkaline battery
Mass
Approx. 100 g (3.5 oz) (including battery)
Accessories
See page 6.
Design and specifications are subject to change without notice.
18
Page 19

Index

A
Auto Track 13
B
Battery 7
C, D
Cleaning 16 Connecting to another audio device 12, 15
E, F, G
Erasing tracks 13
R
Recording 12 Repeat Play 14
S
Skip/search 11
T, U
Transfer 4 Troubleshooting 17
V, W, X, Y, Z
Volume 10, 11
H, I, J, K
Headphones
Putting on 9 Using as stereo headphones 15
L
Locating the first track 11
M, N, O
M.D.S.E (MP3 Digital Sound Enhancer)
14
Music Transfer Solid Memory Edition 4
P, Q
Playback 10 Precautions 16
Additional information
19
Page 20
http://www.aiwa.com/
Sony Corporation Printed in Korea
For the customers in the USA
Loading...