SONY UWP-C2, UWP-S1, UWP-S2, UWP-X2 User Manual

2-347-711-31(1)

Wireless Microphone Package

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

UWP-C1/C2 UWP-S1/S2 UWP-X1/X2

 2003 Sony Corporation

Table of Contents

Configuration of the

Packages ............................. 4

UWP-C1..................................... 4

UWP-C2..................................... 5

UWP-S1 ..................................... 6

UWP-S2 ..................................... 7

UWP-X1 .................................... 8

UWP-X2 .................................... 9

Features .................................. 10

Precautions............................. 12

Parts Identification................. 13

Body-pack transmitter

(UTX-B1)................................. 13

Hand-held microphone

(UTX-H1) ................................ 14

Portable diversity tuner

(URX-P1)................................. 15

Half-rack size diversity tuner

(URX-R1) ................................ 17

Diversity tuner module

(URX-M1) ............................... 18

Power Supply ......................... 20

Inserting the batteries............... 20

Attachment and Installation

Procedures ........................ 23

Attaching the supplied accessories to the body-pack

transmitter (UTX-B1) .............. 23

Attaching the supplied accessory to the hand-held

microphone (UTX-H1) ............ 24

Attaching the supplied accessories to the portable

diversity tuner (URX-P1)......... 24

Installing the diversity tuner

module (URX-M1) .................. 25

Settings ................................... 28

Setting the transmission

channel ..................................... 28

Setting the reception channel ... 29 Setting the attenuation level

of the audio input ..................... 30

Resetting the accumulated

battery use time indication ....... 31

Setting the RF output level ...... 32

Setting the monitor level (portable diversity tuner

(URX-P1) only) ....................... 32

Operation ................................ 33

System Configurations.......... 34

Error Messages ...................... 37

Troubleshooting..................... 38

Specifications......................... 40

Appendix................................. 44

Wireless microphone system

frequency list............................ 44

AC adapter for use with the

URX-R1 ................................... 46

Configuration of the Packages

This operation manual is for the UWP-C1/C2/S1/S2/X1/X2 wireless microphone packages. The contents of each package are described below.

UWP-C1

The UWP-C1 consists of a body-pack transmitter (UTX-B1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C1 makes a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) purposes.

Body-pack transmitter (UTX-B1) (1)

Portable diversity tuner (URX-P1) (1)

Supplied accessories

• Omni-directional lavalier microphone (1)

• XLR-BMP conversion cable (for use with the URX-P1 only) (1)

• Microphone stand adapter (1) • Operation manual (1)

• Wind screen (1)

• Shoe mount adapter (1) • Belt clip (2)

• Holder clip (1)

UWP-C2

The UWP-C2 consists of a hand-held microphone (UTX-H1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C2 makes a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) purposes.

Hand-held microphone (UTX-H1) (1)

Portable diversity tuner (URX-P1) (1)

Supplied accessories

• Microphone holder (1) • Belt clip (1)

• Shoe mount adapter (1) • XLR-BMP conversion cable (for use with the URX-P1 only) (1)

• Microphone stand adapter (1) • Operation manual (1)

Configuration of the Packages

UWP-S1

The UWP-S1 consists of a body-pack transmitter (UTX-B1) and a half-rack size diversity tuner (URX-R1). The UWP-S1 is suitable for constructing a wireless system for AV presentations.

Body-pack transmitter (UTX-B1) (1)

Supplied accessories

• Unidirectional lavalier microphone (1)

• AC adapter (1) (See page 46.)

Half-rack size diversity tuner (URX-R1) (1)

• Wind screen (1) • Holder clip (1)

• Belt clip (1) • Operation manual (1)

UWP-S2

The UWP-S2 consists of a hand-held microphone (UTX-H1) and a half-rack size diversity tuner (URX-R1). The UWP-S2 is suitable for constructing a wireless system for AV presentations.

Hand-held microphone (UTX-H1) (1)

Supplied accessories

• Microphone holder (1) • AC adapter (1) (See page 46.)

• Operation manual (1)

Half-rack size diversity tuner (URX-R1) (1)

Configuration of the Packages

UWP-X1

The UWP-X1 consists of a body-pack transmitter (UTX-B1) and a diversity tuner module (URX-M1). By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible.

Body-pack transmitter (UTX-B1) (1)

Diversity tuner module (URX-M1) (1)

Supplied accessories

• Unidirectional lavalier microphone (1)

• Belt clip (1) • Operation manual (1)

• Wind screen (1) • Holder clip (1)

UWP-X2

The UWP-X2 consists of a hand-held microphone (UTX-H1) and a diversity tuner module (URX-M1) . By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible.

Hand-held microphone (UTX-H1) (1)

Supplied accessories

• Microphone holder (1)

Diversity tuner module (URX-M1) (1)

• Operation manual (1)

Features

Each of the UWP-C1/C2/S1/S2/X1/ X2 wireless microphone packages (referred to as the UWP series hereafter) combines a transmitter (body-pack transmitter (UTX-B1) or hand-held microphone (UTX-H1)) and a receiver (portable diversity tuner (URX-P1), half-rack size diversity tuner (URX-R1), or diversity tuner module (URX-M1)). The UWP series can be used with a compact camcorder for ENG (Electronic News Gathering) purposes, and with a powered mixer for AV presentations or as a PA (public address) system.

Note

The UWP series is not compatible with conventional WRT series transmitters, WRR series tuners, or WRU series tuner units.

The features of each package are described below.

UWP-C1

Body-pack transmitter (UTX-B1)

This is a small and lightweight transmitter with a crystal-controlled PLL (phase lock loop) synthesized system and a BMP-type microphone input connector. The RF power output can be set at 10 mW or at 2 mW.

Portable diversity tuner (URX-P1)

This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with an adapter for mounting the tuner on the compact camcorder (DSR-PDX10/PDX10P/PD150/ PD150P, etc.).

UWP-C2

Hand-held microphone (UTX-H1)

This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 10 mW or at 2 mW.

Portable diversity tuner (URX-P1)

UWP-S1

Body-pack transmitter (UTX-B1)

Half-rack size diversity tuner (URX-R1)

This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with two types of audio connectors (1/4-inch jack and XLR type) on the rear panel.

UWP-S2

Hand-held microphone (UTX-H1)

This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 10 mW or at 2 mW.

Half-rack size diversity tuner (URX-R1)

This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with two types of audio connectors (1/4-inch jack and XLR type) on the rear panel.

UWP-X2

Hand-held microphone (UTX-H1)

This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 10 mW or at 2 mW.

Diversity tuner module (URX-M1)

This tuner module can be incorporated into the MB-806A Tuner Base Unit or SRP-X700P Powered Mixer.

UWP-X1

Body-pack transmitter (UTX-B1)

Diversity tuner module (URX-M1)

This tuner module can be incorporated into the MB-806A Tuner Base Unit or SRP-X700P Powered Mixer.

Precautions

• The UWP series product must be used within a temperature range of 0°C to 40°C (32°F to 104°F).

• Operating the UWP series product near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the UWP series product as far from such equipment as possible.

• The presence of the lighting equipment may produce electrical interference over the entire frequency range. Position the UWP series product so that interference is minimized.

• To avoid degradation of the signalto-noise ratio, do not use the UWP series product in noisy places or in locations subject to vibration, such as the following: — near electrical equipment, such as

motors, transformers or dimmers

— near air conditioning equipment

or places subject to direct air

flow from an air conditioner — near public address loudspeakers — where adjacent equipment might

knock against the tuner Keep the UWP series product as far from such equipment as possible or use buffering material.

• Clean the surface and the connectors of the UWP series product with a dry, soft cloth. Never use thinner, benzene, alcohol or any other chemicals, since these may mar the finish.

To prevent electromagnetic interference from portable communication devices

The use of portable telephones and other communication devices near the UWP series product may result in malfunction and interference with audio signals. It is recommended that portable communication devices near the UWP series product be turned off.

Parts Identification

Body-pack transmitter (UTX-B1)

1 Antenna

2 Audio input connector

Connect the supplied lavalier microphone here.

A AF (audio frequency) indication

Appears whenever the input audio signal is stronger than the reference level.

B RF (antenna output) indication

Appears during signal transmission from the antenna.

C RF (antenna output) level indication

Shows the RF output level setting.

For details, see “Setting the RF output level” on page 32.

D BATT (battery) indication

Shows the battery condition.

For details, see “Power Supply” on page 20.

E CH (channel) indication

Shows the transmission channel. Each time you press the SET button in transmission mode, the channel indication changes as follows.

For details, see “Settings” on page

28.

3 Power indicator

Lights up red when the transmitter is tuned on.

4 Display section

AF RFCHBATT

H L

Transmission channel

Transmission frequency

Attenuation level of the input signal

Accumulated battery use time

Press the SET button.

Parts Identification

5 + (+ selection) / – (– selection/

reset) buttons

Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The “–” button resets the accumulated battery use time to “00:00”.

6 Battery compartment

Accommodates two LR6 (size AA) alkaline batteries.

For details on how to insert the batteries, see “Power Supply” on page 20.

7 SET button

Press to change and enter display parameters.

For details, see “Settings” on page

28.

8 POWER switch

Turns the power of the transmitter ON or OFF.

1 Power indicator

Lights up red when the microphone is turned on.

2 POWER switch

Turns the power of the microphone ON or OFF.

3 Battery compartment

Accommodates two LR6 (size AA) alkaline batteries.

For details on how to insert the batteries, see “Power Supply” on page 20.

4 Display section

H L

Hand-held microphone (UTX-H1)

The rear side of the battery compartment

A AF (audio frequency) indication

Appears whenever the input audio signal is stronger than the reference level.

B RF (antenna output) indication

Appears during signal transmission from the antenna.

C RF (antenna output) level indication

Shows the RF output level setting.

For details, see “Setting the RF output level” on page 32.

D BATT (battery) indication

Shows the battery condition.

For details, see “Power Supply” on page 20.

E CH (channel) indication

Shows the transmission channel. Each time you press the SET button, the channel indication changes as follows.

For details, see “Settings” on page

28.

Transmission channel

Portable diversity tuner (URX-P1)

Transmission frequency

Attenuation level of the input signal

Accumulated battery use time

Press the SET button.

1 Antennas a/b

The angle of the antennas can be

5 + (+ selection) / – (– selection/

reset) buttons

Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The “–” button resets the accumulated battery use time to “00:00”.

6 SET button

Press to change display parameters.

For details, see “Settings” on page

28.

......................................................................................................................................................................

adjusted manually.

2 MONITOR connector (3.5-mm

diameter stereo mini jack)

To monitor the tuner output, connect the headphones to this connector.

3 RF (radio frequency) indicator

Indicates the strength of the RF input signal.

On in green: RF input is 15 dBµ*

or more.

Off: RF input is less than 15 dBµ*.

* 0 dBµ = 1 µVEMF

+ 33 hidden pages