Sony STR-K1600 Service Manual

1
SERVICE MANUAL
E Model
Australian Model
STR-K1600
MULTI CHANNEL AV RECEIVER
Amplifier section
1)
Stereo mode output (rated) (6 ohms, 1 kHz, THD 1%)
90 W + 90 W
1)
85 W + 85 W
3)
Surround mode output (reference)
2)
RMS output
FRONT: 185 W per channel
1)
170 W per channel
3)
(with SS-MSP16)
CENTER: 185 W
1)
170 W
3)
(with SS-CNP16)
SURROUND: 185 W per channel
1)
170 W per channel
3)
(with SS-SRP16)
SPECIFICATIONS
SURROUND BACK: 185 W
1)
170 W
3)
(with SA-WP16)
1) Measured under the following conditions: Area code Power requirements
E51, AUS, MY, SP, TH 240 V AC, 50 Hz MX 127 V AC, 60 Hz AR 230 V AC, 50 Hz
2) Reference power output for front, center surround and surround back speakers. Depending on the sound field settings and the source, there may be no sound output.
3) Measured under the following conditions:
Area code Power requirements AR 220 V AC, 50 Hz
Ver. 1.1 2007. 04
9-887-570-02
2007D04-1 © 2007. 04
Sony Corporation
Home Audio Division Published by Sony Techno Create Corporation
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS-ES | Neo:6” are registered trademarks of DTS, Inc. “96/24” is a trademark of DTS, Inc.
This receiver incorporates High-Definition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
– Continued on next page –
Photo: Silver type
2
STR-K1600
Inputs
Analog Sensitivity: 800 mV/
50 kohms
Digital (Coaxial) Impedance: 75 ohms
Outputs (Analog)
AUDIO OUT Voltage: 800 mV/10 kohms SUB WOOFER Voltage: 2 V/1 kohm
Tone
Gain levels ±6 dB, 1 dB step
Reproduction frequency range:
28 – 20,000 Hz
FM tuner section
Tuning range 87.5 – 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
Models of area code AUS, MY, SP, TH With 9-kHz tuning scale: 531 – 1,602 kHz Models of area code E51 With 10-kHz tuning scale: 530 – 1,610 kHz
4)
With 9-kHz tuning scale: 531 – 1,602 kHz
4)
Models of area code AR, MX
With 10-kHz tuning scale: 530 – 1,610 kHz Antenna Loop antenna Intermediate frequency 450 kHz
4) You can change the AM tuning scale to 9 kHz or 10 kHz.
After tuning in any AM station, turn off the receiver.
While holding down TUNING MODE, press ?/1. All
preset stations will be erased when you change the tuning
scale. To reset the scale to 10 kHz (or 9 kHz), repeat the
procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms PR/CR: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through
General
Power requirements Area code Power requirements
AUS 240 V AC, 50 Hz MY, SP 230 – 240 V AC, 50/60 Hz AR, TH 220 – 230 V AC, 50/60 Hz MX 127 V AC, 60 Hz E51 120/220/240 V AC, 50/60 Hz
Power output (DIGITAL MEDIA PORT) (Models of area code AUS, MY, SP, TH only)
DC OUT: 5 V, 700 mA Power consumption 200 W Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 × 157.5 × 316 mm including projecting parts and controls
Mass (Approx.) 8.0 kg
Design and specifications are subject to change without notice.
•Abbreviation
E51 : Chilean and Peruvian models AUS: Australian model MY : Malaysia model SP : Singapore model TH : Thai model MX : Mexican model AR : Argentina model
Ver. 1.1
3
STR-K1600
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MODEL IDENTIFICATION
— BACK PANEL —
Part No.
MODEL PART No.
MY, SP 2-897-800-0s AUS 2-897-800-1s E51 2-897-800-2s AR 2-897-800-3s MX 2-897-800-4s TH 3-208-699-0s
•Abbreviation MY : Malaysia model SP : Singapore model AUS: Australian model E51 : Chilean and Peruvian models AR : Argentina model MX : Mexican model TH : Thai model
Ver. 1.1
4
STR-K1600
TABLE OF CONTENTS
1. GENERAL
Description and location of parts............................................. 5
2. DISASSEMBLY
2-1. Case .....................................................................................8
2-2. Back Panel Section.............................................................. 9
2-3. Front Panel Section ............................................................. 9
2-4. DIGITAL Board ................................................................10
2-5. MAIN Board Section ........................................................ 10
2-6. STANDBY Board ............................................................. 11
3. TEST MODE ..................................................................... 12
4. FM TUNER CHECK .......................................................13
5. DIAGRAMS
5-1. Block Diagram – Tuner/Audio Section –.......................... 15
5-2. Block Diagram – Digital Section – ................................... 16
5-3. Block Diagram – Video Section – ..................................... 17
5-4. Block Diagram – HDMI SW Section –............................. 18
5-5. Block Diagram – Key/Display Section – .......................... 19
5-6. Block Diagram – Power Section – .................................... 20
5-7. Printed Wiring Boards – Main Section – .......................... 22
5-8. Schematic Diagram – Main Section (1/2) – ...................... 23
5-9. Schematic Diagram – Main Section (2/2) – ...................... 24
5-10. Printed Wiring Board – Digital Section (1/2) – ................ 25
5-11. Printed Wiring Board – Digital Section (2/2) – ................ 26
5-12. Schematic Diagram – Digital Section (1/4) – ................... 27
5-13. Schematic Diagram – Digital Section (2/4) – ................... 28
5-14. Schematic Diagram – Digital Section (3/4) – ................... 29
5-15. Schematic Diagram – Digital Section (4/4) – ................... 30
5-16. Printed Wiring Boards – Video Section – ......................... 31
5-17. Schematic Diagram – Video Section –.............................. 32
5-18. Printed Wiring Board – HDMI SW Section –................... 33
5-19. Schematic Diagram – HDMI SW Section – ..................... 34
5-20. Printed Wiring Boards – DCAC, Power Key Section – .... 35
5-21. Schematic Diagram – DCAC, Power Key Section – ........ 35
5-22. Printed Wiring Board – Display Section – ........................ 36
5-23. Schematic Diagram – Display Section –........................... 37
5-24. Printed Wiring Board – Power Section – .......................... 38
5-25. Schematic Diagram – Power Section – ............................. 39
5-26. Printed Wiring Board
– DCDC Section (AUS, MY, SP, TH model) – ................. 40
5-27. Schematic Diagram
– DCDC Section (AUS, MY, SP, TH model) – ................. 40
6. EXPLODED VIEWS
6-1. Case Section ...................................................................... 49
6-2. Front Panel Section ...........................................................50
6-3. Back Panel Section............................................................ 51
6-4. Chassis Section ................................................................. 52
7. ELECTRICAL PARTS LIST ........................................ 53
Ver. 1.1
5
STR-K1600
SECTION 1
GENERAL
This section is extracted from instruction manual.
5
GB
Getting Started
Description and location of parts
Front panel
Getting Started
Receiver
?/1
AUTO CAL MIC
AUTO CAL
TUNING MODE
TUNING
– +
PHONES
MEMORY/
ENTER SLEEPDIMMER
MULTI CHANNEL DECODING
SUR BACK DECODING
2CH A.F.D. MOVIE MUSIC
MODE SPEED
X-ROUND
DISPLAY INPUT MODE
INPUT SELECTOR
MASTER VOLUME
VIDEO 3 IN/PORTABLE AV IN
VIDEO L AUDIO R
6
q;
w
s
qaqsw;wa ql
1
2
345 789
qf
qgqhqjqk qd
Name Function
A ?/1
(on/standby)
Press to turn the receiver on or off (page 31, 39, 40, 57, 70, 78).
B AUTO CAL Press to activate the Auto
Calibration function (page
33).
C TUNING MODE Press to select the tuning
mode (page 58, 61, 78).
D Display The current status of the
selected component or a list of selectable items appears here (page 7).
E MULTI CHANNEL
DECODING lamp
Lights up when multi channel audio is decoded (page 40).
F Remote sensor Receives signals from
remote commander.
Name Function
G DISPLAY Press to select information
displayed on the display (page 66, 67).
H INPUT MODE Press to select the input
mode when the same components are connected to both digital and analog jacks (page 62).
I MASTER
VOLUME
Turn to adjust the volume level of all speakers at the same time (page 36, 37, 39, 40).
J X-ROUND MODE Press to select the X-
ROUND mode (page 66).
X-ROUND SPEED
Press to adjust the speed of X-ROUND effect (page
66).
continued
6
GB
Name Function
K INPUT
SELECTOR
Turn to select the input source to playback (page 37, 39, 40, 58, 59, 60, 61, 62, 65, 67, 68, 69).
L MOVIE,
MUSIC
Press to select sound fields (MOVIE, MUSIC) (page
54).
M A.F.D. Press to select A.F.D.
mode (page 52, 56).
N 2CH Press to select 2CH
STEREO mode (page 56,
57).
O SUR BACK
DECODING
Press to select the surround back decoding mode (page 46).
P SLEEP Press to activate the Sleep
Timer function and the duration which the receiver turns off automatically (page 68).
Q DIMMER Press to change the
brightness of the display (page 51).
R MEMORY/
ENTER
Press to store a station or enter the selection when selecting the settings (page 31)
S TUNING +/– Turn to scan a station
(page 58, 61).
T VIDEO 3 IN/
PORTABLE AV IN jacks
To connect a camcorder or video game (page 27, 37).
U AUTO CAL MIC
jack
Connects to the supplied optimizer microphone for the Auto Calibration function (page 32).
V PHONES jack Connects to a headphone
(page 74).
7
GB
Getting Started
About the indicators on the display
SW
LFE
LC
SL S
;
D EX;PL IIx;PL OPT DTS -ES 96/24 MEMORY ST
MONOD.RANGECOAX NEO:6
SB
R
SR
1 2 3 54 6 87
9q;qd qs qa
Name Function
A SW Lights up when the audio signal
is output from the SUB WOOFER jack.
B LFE Lights up when the disc being
played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced.
C ; D (EX) “; D” lights up when Dolby
Digital signals are input. “; D EX” lights up when Dolby Digital Surround EX signals are decoded.
Note
When playing a Dolby Digital format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG” (page 62).
D ; PL
(II)/(IIx)
“; PL” lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. “; PL II” lights up when the Pro Logic II Movie/Music/ Game decoder is activated. “; PL IIx” lights up when the Pro Logic IIx Movie/Music/ Game decoder is activated.
Note
Dolby Pro Logic IIx decoding does not function for DTS format signals or for signals with a sampling frequency of more than 48 kHz.
Name Function
E OPT Lights up when INPUT MODE
is set to “AUTO IN” and the source signal is a digital signal being input through the OPTICAL jack, or when INPUT MODE is set to “OPT IN” (page 62).
F DTS (-ES)/
(96/24)
“DTS” lights up when the receiver is decoding DTS signals. “DTS-ES” lights up when the receiver is decoding DTS-ES signals. “DTS 96/24” lights up when the receiver is decoding DTS 96 kHz/24 bit signals.
Note
When playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG” (page 62).
G MEMORY Lights up when a memory
function, such as Preset Memory (page 60), etc., is activated.
H Tuner
indicators
Lights up when using the receiver to tune in radio stations (page 58), etc.
I Preset
station indicators
Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 60.
J D.RANGE Lights up when dynamic range
compression is activated (page
44).
continued
8
GB
Name Function
K NEO:6 Lights up when DTS Neo:6
Cinema/Music decoder is activated (page 53).
L COAX Lights up when INPUT MODE
is set to “AUTO IN” and the source signal is a digital signal being input through the COAXIAL jack, or when INPUT MODE is set to “COAX IN” (page 62).
M Playback
channel indicators
L R C SL SR S
SB
The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound. Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing) Surround back (the surround back components obtained by
6.1 channel decoding)
Example:
Recording format (Front/ Surround): 3/2.1 Sound Field: A.F.D. AUTO
SW
LC
SL
R
SR
6
STR-K1600
9
GB
Getting Started
Rear panel
1
45
23
76
Y
P
B/CB
PR/C
R
HDMI
DVD IN VIDEO 2/BD IN OUT
SA-CD/CD/CD-R
D-LIGHT
SYNC OUT
TV
L
R
OUT IN IN
SAT
AUDIO IN
VIDEO IN
DVD
AUDIO IN
VIDEO IN
VIDEO 1
AUDIO OUT
VIDEO OUT
VIDEO OUT
SAT IN
MONITOR OUT
VIDEO 1 IN
SURROUND BACK
SURROUND
CENTER
FRONT
DVD IN
AUDIO IN
AUDIO OUT
VIDEO IN
LRL
RLR
LRL
R
MONITOR
COMPONENT VIDEO
DIGITAL
DMPORT
OPTICAL
SAT IN
DVD IN
COAXIAL
ANTENNA
VIDEO 2/ BD IN
AM
SUB WOOFER
SPEAKERS
A DIGITAL INPUT/OUTPUT section
OPTICAL IN jack
Connects to a DVD player, etc. The COAXIAL jack provides a better quality of loud sound (page 24,
26).
COAXIAL IN jack
HDMI IN/ OUT jack
a)
Connects to a DVD player, etc. The image and the sound are output to a TV or a projector (page 21).
DMPORT jack
b)
Connects to a DIGITAL MEDIA PORT adapter (page 64).
B ANTENNA section
FM ANTENNA jack
Connects to the FM wire antenna supplied with this receiver (page 29).
AM ANTENNA terminals
Connects to the AM loop antenna supplied with this receiver (page 29).
C COMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT VIDEO INPUT/ OUTPUT jack
a)
Connects to a DVD player, TV, a satellite tuner, etc. You can enjoy high quality image (page 23, 24, 26).
D SPEAKER section
Connects to the speakers (page 17).
Connects to the sub woofers (page 17).
E VIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/ OUT jack
Connects the video and audio jacks of a VCR, DVD player, etc. (page 23, 24, 26, 27).
VIDEO IN/ OUT jack
a)
Green (Y)
Blue (P
B/CB
)
Red (P
R/CR
)
White (L)
Red (R)
Yellow
continued
10
GB
a)
You can watch the selected input image when you connect the HDMI OUT or MONITOR OUT jack to a TV (page 23).
b)
Models of area code SP, AU only.
F AUDIO INPUT/OUTPUT section
AUDIO IN/ OUT jack
Connects to an Super Audio CD player or CD recorder, etc. (page
27).
G D-LIGHT SYNC OUT section
D-LIGHT SYNC OUT jack
Connects to a lighting device (page 28).
White (L)
Red (R)
11
GB
Getting Started
You can use the supplied remote RM-AAU013 (models of area code E51, MX, AR only) or RM­AAU015 (models of area code AUS, MY, SP, TH only) to operate the receiver and to control the Sony audio/video
components that the remote is assigned to operate. For details, see “Changing
button assignments”
(page 69).
Remote commander
123 46 78
0/10
ENTER
9
SYSTEM STANDBY
TV INPUT
SLEEP
DMPORT
TV
?/1
AV
?/1
VIDEO 1 VIDEO 2 VIDEO 3 DVD
2CH A.F.D.
RETURN/EXIT TV CH – PRESET –
TV CH +
PRESET +
TUNING –TVTUNING +
REPLAY ADVANCE
MENU
MOVIE MUSIC
MEMORY DVD MENU
FM MODE
CLEAR
TOOLSDISPLAY
MUTING
TV VOL
MASTER VOL
AUTO CAL
D.TUNING
D.SKIP
AMP MENU
SAT TV SA-CD/CD TUNER
?/1
-
F
Gg
f
.
HmM
Xx
<
<
>
5
>10/
RM-AAU013
(Models of area code E51, MX, AR only)
123 46 78
0/10
ENTER
9
SYSTEM STANDBY
TV INPUT
SLEEP
AUTO CAL
TV
?/1
AV
?/1
VIDEO 1 VIDEO 2 VIDEO 3 DVD
2CH A.F.D.
RETURN/EXIT TV CH – PRESET –
TV CH + PRESET +
TUNING –TVTUNING +
REPLAY ADVANCE
MENU
MOVIE MUSIC
MEMORY DVD MENU
CLEAR
TOOLSDISPLAY
MUTING
TV VOL
MASTER VOL
FM MODE
D.TUNING
D.SKIP
AMP MENU
SAT TV SA-CD/CD TUNER
?/1
-
F
Gg
f
.
HmM
Xx
<
<
>
5
>10/
wf
qg
qj
qk
qh
qf
ql
w;
wd
qd
ws
1
3
2
5
6
7 8
q;
9
qs
qa
4
wa
RM-AAU015
(Models of area code AUS, MY, SP, TH only)
qg
qj
qk
qh
qf
ql
w;
wd
qd
ws wa
3
6
8
1
2
5
7
q;
9
qs
qa
4
continued
12
GB
Name Function
A TV ?/1
(on/standby)
Press TV ?/1 and TV (M) at the same time to turn the TV on or off.
AV ?/1 (on/standby)
Press to turn on or off the Sony audio/video components that the remote is assigned to operate. If you press ?/1 (B) at the same time, it will turn off the receiver and other components (SYSTEM STANDBY).
Note
The function of the AV ?/1 switch changes automatically each time you press the input buttons (C).
B ?/1
(on/standby)
Press to turn the receiver on or off. To turn off all components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY).
C Input
buttons
Press one of the buttons to select the component you want to use. When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components as follows. You can change the button assignments following the steps in “Changing button assignments” on page 69.
Button Assigned Sony
component
VIDEO 1 VCR (VTR mode 3) VIDEO 2 VCR (VTR mode 1) VIDEO 3 Not assigned DVDDVD player SAT Digital Satellite
Receiver
TV TV SA-CD/CD Super Audio CD/
CD player TUNER Built-in tuner DMPORT
(RM-AAU015 only)
DIGITAL MEDIA
PORT adapter
Name Function
D MOVIE Press to select sound fields
(MOVIE).
MUSIC Press to select sound fields
(MUSIC).
E AMP MENU Press to display the menu of
the receiver. Then, use V, v, B, b and (P) to perform menu operations.
F FM MODE
(RM-AAU013 only)
Press to select the FM monaural or stereo reception.
AUTO CAL (RM-AAU015 only)
Press to activate the Auto Calibration function (page
33).
G D.TUNING Press to enter direct tuning
mode.
D.SKIP Press to skip a disc when
using a multi-disc changer.
H DVD MENU Press to display the menu of
the DVD player on the TV screen. Then, use V, v, B, b and (P) to perform menu operations.
FM MODE (RM-AAU015 only)
Press to select the FM monaural or stereo reception.
I ENTER Press to enter the value after
selecting a channel, disc or track using the numeric buttons of the TV, VCR or satellite tuner.
MEMORY Press to store a station.
J MUTING Press to activate the muting
function. Press MUTING and TV (M) at the same time to activate the TV’s muting function.
K TV VOL
+
a)
/–
Press TV VOL +/– and TV (M) at the same time to adjust the TV volume level.
MASTER VOL +
a)
/–
Press to adjust the volume level of all speakers at the same time.
Ver. 1.1
7
STR-K1600
13
GB
Getting Started
Name Function
L TV CH +/– Press TV CH +/– and TV (M)
at the same time to select preset TV channels.
PRESET +/– Press to select
–preset stations. –preset channels of the VCR
or satellite tuner.
./>
b)
Press to skip a track of the CD player, DVD player or Blu­ray disc player.
REPLAY / ADVANCE
Press to replay the previous scene or fast forward the current scene of the VCR, DVD player or Blu-ray disc player.
m/M
b)
Press to –search tracks in the forward/
reverse direction of the DVD player.
–start fast forward/rewind of
the VCR, CD player or Blu­ray disc player.
TUNING +/– Press to scan a station.
H
a)b)
Press to start playback of the VCR, CD player, DVD player or Blu-ray disc player.
X
b)
Press to pause playback or recording of the VCR, CD player, DVD player or Blu­ray disc player. (Also starts recording with components in recording standby.)
x
b)
Press to stop playback of the VCR, CD player, DVD player or Blu-ray disc player.
M TV Press TV and the button you
want at the same time to activate the buttons with orange printing.
N MENU Press to display the menu of
the VCR, DVD player, satellite tuner or Blu-ray disc player on the TV screen. Press MENU and TV (M) at the same time to display the TV’s menu. Then, use V, v, B, b and (P) to perform menu operations.
<
<
Name Function
O RETURN/
EXIT O
Press to –return to the previous menu. –exit the menu while the
menu or on-screen guide of the VCR, DVD player, satellite tuner or Blu-ray disc player is displayed on
the TV screen. Press RETURN/EXIT and TV (M) at the same time to return to the previous menu or exit the TV’s menu while the menu is displayed on the TV screen.
P
V/v/B/b
After pressing AMP MENU (E), DVD MENU (H) or MENU (N), press V, v, B or b to select the settings. Then, press to enter the selection for DVD MENU or MENU. Press also to enter the selection of the receiver, VCR, satellite tuner, CD player, DVD player or Blu­ray disc player.
Q DISPLAY Press to select information
displayed on the TV screen of the VCR, satellite tuner, CD player, DVD player or Blu­ray disc player. Press DISPLAY and TV (M) at the same time to select TV information displayed on the TV screen.
R TOOLS Press to display options
applicable to the entire disc (e.g. disc protection), recorder (e.g. audio settings during recording), or multiple items on a list menu (e.g. erasing multiple titles). Press TOOLS and TV (M) at the same time to display options applicable to the TV.
continued
14
GB
a)
The number 5, MASTER VOL +, TV VOL + and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.
b)
This button is also available for DIGITAL MEDIA PORT adapter operation. For details on the function of the button, see the operating instructions supplied with the DIGITAL MEDIA PORT adapter.
Notes
•The VIDEO 3 button on the remote is not available for receiver operation.
•Some functions explained in this section may not work depending on the model.
•The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.
Name Function
S >10/
x
Press to select –track numbers over 10 of the
VCR, satellite tuner or CD player.
–channel numbers of the
Digital CATV terminal.
-/-- Press -/-- and TV (M) at the
same time to select the channel entry mode, either one or two digits of the TV.
CLEAR Press to clear a mistake when
you press the incorrect numeric button.
T Numeric
buttons (number 5
a)
)
Press to –preset/tune to preset
stations.
–select track numbers of the
CD player, DVD player or Blu-ray disc player. Press 0/ 10 to select track number 10.
–select channel numbers of
the VCR or satellite tuner. Press the numeric buttons and TV (M) at the same time to select the TV channels.
U A.F.D. Press to select A.F.D. mode. V 2CH Press to select 2CH STEREO
mode.
W TV INPUT Press TV INPUT and TV (M)
at the same time to select the input signal (TV input or video input).
SLEEP Pre ss to activate the Sleep
Timer function and the duration which the receiver turns off automatically.
X AUTO CAL
(RM-AAU013 only)
Press to activate the Auto Calibration function.
8
STR-K1600
Note : This set can be disassemble according to the following sequence.
SECTION 2
DISASSEMBLY
2-1. CASE
Note : Follow the disassembly procedure in the numerical order given.
1
two
screws
(case 3 TP2)
2
two
screws
(case 3 TP2)
3
two
screws
(+BVTP 3
×
8
)
4
case
2-1. CASE
(Page 8)
2-3. FRONT PANEL SECTION
(Page 9)
SET
2-2. BACK PANEL SECTION
(Page 9)
2-6. STANDBY BOARD
(Page 11)
2-4. DIGITAL BOARD
(Page 10)
2-5. MAIN BOARD SECTION
(Page 10)
9
STR-K1600
2-2. BACK PANEL SECTION
2-3. FRONT PANEL SECTION
6
five
screws
(+BVTP 3
×
8)
1
CNP790 (4P)
7
front panel section
3
CNP507 (3P)
4
CN506 (3P)
5
CNP503 (3P
)
2
wire (flat type) (19 core)
(CNS514)
8
three
screws
(+BVTP 3
×
8)
9
five
screws
(+BVTP 3
×
8)
0
three
screws
(+BVTP 3
×
8)
6
three
screws
(+BVTP 3
×
8)
7
screw
(+BVTP 3
×
8)
qa
screw
(+BVTP 3
×
8)
qs
back panel section
1
CNP901 (2P)
2
CNP202 (3P)
3
CNP203 (3P)
4
wire (flat type) (13 core)
(CNS509)
5
wire (flat type) (9 core)
(CNS507)
10
STR-K1600
2-4. DIGIT AL BOARD
2-5. MAIN BOARD SECTION
4
screw
(+BVTP 3
×
8)
5
DIGITAL board
1
CNP505 (7P)
3
CNP512 (3P)
2
CNP503 (8P)
7
two
screws
(+BV3 (3
-CR)
)
8
MAIN board sectio
n
6
two
screws
(+BV3 (3
-CR)
)
5
screw
(+BV3 (3
-CR)
)
1
CNP801 (5P)
2
CNP802 (5P)
3
CNP912 (2P)
4
CN915 (5P)
11
STR-K1600
2-6. STANDBY BOARD
5
STANDBY board
2
CNP804 (3P)
3
CNP805 (3P)
1
CNP902 (2P)
4
screw
(+BVTP 3
×
8)
12
STR-K1600
SECTION 3
TEST MODE
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (E51 model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the ?/1 button to turn off the main power. While depressing the [TUNING MODE] button, press the ?/1 button to turn on the main power. Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same time, then each segment lights on one after another.
* Procedure:
While depressing the [DIMMER] and the [DISPLAY] buttons si­multaneously, press the ?/1 button to turn on the main power.
1. ALL segments light on.
[MULTI CHANNEL DECODING] LED light on.
2. Turn the [INPUT SELECTOR] control, confirm display.
[MULTI CHANNEL DECODING] LED light off.
3. Turn the [INPUT SELECTOR] control, confirm display.
[MULTI CHANNEL DECODING] LED light on.
4. Turn the [INPUT SELECTOR] control, all segments and LED light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn on the main power. The message “S.F. CLR.” appears for a moment and initializa­tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed. * Procedure:
While depressing the [AUTO CAL] and the [DISPLAY] buttons simultaneously, press the ?/1 button to turn on the main power. The model name, destination and the software version are dis­played for a moment.
KEY CHECK MODE
* Button check * Procedure:
While depressing the [AUTO CAL] and the [2CH] buttons simul­taneously, press the
?/1 button to turn on the main power.
Either the message “REST 14” appears. Every pressing of any button other than the
?/1 counts down
the buttons. The buttons which are already counted once are not counted again. When all buttons are pressed “REST 00” appears.
SWAP ALL MODE
* The signal will be swap to all channel so that all speaker will
have sound output.
* Procedure:
1. While depressing the [AUTO CAL] and the [A.F.D.] buttons si- multaneously, press the po wer ?/1 button to turn on the main power.
2. “SWP. ALL” appears. (No change while displayed.)
SHIPMENT MODE
All preset contents are reset to the default setting. * Procedure:
1. While depressing the [AUTO CAL] and the [MUSIC] buttons si- multaneously, press the po wer ?/1 button to turn on the main power.
2. “CLEARED” appears and switch off the set.
DCAC FACT ORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
Factory Test System Setup
1. When power off: Press the three buttons [MEMORY/ENTER] + [MOVIE] +
?/1 .
“DCAC[]FTM” appears. Afterward, press the [TUNING MODE] to start DCAC factory test mode.
L
SW
CR
SL S SR
SBL SB SBR
LFE
SP A
NEO:6COAXHDMI
DEX DTS -ESxIIPL RDS STCAT96/24
MONOD.RANGESAT
D
DDD
PL OPT
D
D
dB
Hzk
ft.m
MHz
MEMORY
SP B
L R
S
LFE
NEO:6COAXHDMI
EX -ESx RDS
MONOD.RANGESAT
k m MHz
SP B
LFE
SP A
NEO:6COAXHDMI
EX -ESxIIPL STCAT96/24
MONOD.RANGESAT
D
D
OPT
dB
Hz
ft.
MEMORY
SP B
DSP Data Line
Check
Start Pass Pass
Auto Cal Mic
Check
END
SPK Front Left
DCAC MIC
Receiver
Ver. 1.1
13
STR-K1600
SECTION 4
FM TUNER CHECK
FM AUTO STOP CHECK
(1) Turn on the set. (2) Input the following signal from Signal Generator to FM
antenna input directly.
* Carrier Frequency: A=87.5 MHz, B=98 MHz, C=108 MHz Deviation : 75 kHz Modulation : 1 kHz ANT input : 35 dBu (EMF)
(Note)
Please use 75 ohm “coaxial cable” to connect SG and the set. You cannot use video cable for checking. Please use SG whose output impedance is 75 ohm.
(3) Set to FM tuner function and scan the input FM signal with
automatic scanning.
(4) Confirm that input Frequency of A, B and C are detected and
automatic scanning stops.
The stop of automatic scanning means “The station signal is received in good condition.”
1. DCAC DSP Data Line Checking
After press the [TUNING MODE], DCAC Factory test mode will start, below display will show: “DCAC[][][]x” x=1, 2, 3 If there is error happen, below display will show:
“ERR[]SD0x” x=1 t D1501 or R1530 problem
x=2 t D1502 problem x=3 t D1503 problem
2. DCAC board Checking
Connect front left speaker of the receiver and AUTO CAL micro­phone. Turn [MASTER VOLUME] jog, there will be test tone sound output from front left speaker, and the display will change accord­ingly.
“AD[]-[]xxx” xxx=0 to 255 (depends on loudness of test tone)
Ver. 1.1
14
STR-K1600
• Circuit Boards Location
SECTION 5
DIAGRAMS
MAIN board
DIGITAL board
HDMI SW board
VIDEO boar
d
DCDC board (AUS, MY, SP, TH model)
DISPLAY board
POWER KEY board
DCAC board
HEADPHONE board
VIDEO 3 board
STANDBY board
AC SELECT board (E51 model)
Ver. 1.1
STR-K1600
15 15
STR-K1600
5-1. BLOCK DIAGRAM — TUNER/AUDIO SECTION —
(Page 16)
(Page 20)
C-CH
SR-CH
R-CH
SL-CH
L-CH
R-IN
L-IN
SW
SEL
C
SEL
SL SEL
R-CH
R-CH
R-CH
DIR
FUNCTION SELECT
IC401
VCCVEE
+7V
SEL SW
MCU
I/F
–7V
SW OUT
C OUT
R OUT
SL OUT
L OUT
• Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (ANALOG)
• R-ch is omitted due to same as L-ch.
• Abbreviation AUS: Australian model MY : Malaysia model SP : Singapore model TH : Thai model
43
74 73
AUDIO
LR
VIDEO 3 IN/
PORTABLE AV IN
TV
AM
BUFFER
IC3002
TN1
FM/AM TUNER UNIT
SYSTEM
CONTROL
IC1101 (1/6)
SA-CD/CD/CD-R
LRLR
J298 (2/2) J405 (1/2)
R-CH
SLATCH
R–CH
47
TUNER_DATA
46
TUNER_CLK
VOL_IC_DA VOL_IC_CL
RDS SIG
DO/SD/ST
L-CH
R-CH
NC
CE
DO/ST
DI
CL
DET
C LINK_RX
C LINK_TX
L
7 5 6
13
14
2
4
R
VBUS+5V
VIDEO 5V
AUS,MY,SP,TH MODEL
R-CH
R-CH
R-CH
R-CH
R-CH
R-CH
TU+9V
27
FLASH2/C LINK_RX
26
LINK DET
28
FLASH1/C LINK_TX
60 59
FM 75
COAXIAL
ANTENNA
DMPORT
J1311
-3 -4 -5 -6-2 -3
+7V
10
AUDIO IN
LR
VIDEO 1
J402 (1/2)
R-CH
-3 -4
OUT
LR
J405 (2/2)
SA-CD/CD/CD-R
-1 -2
R-CH
AUDIO OUT
LR
J402 (2/2)
VIDEO 1
-1 -2
IN IN
DVD
LRLR
J403
-1 -2 -3 -4
AUDIO IN
SAT
AUDIO IN
68 66
60 59
42
88
87
85
84
SW-CH
SBL-CH
86
56 51 52 49
26 30 32 34 24 28
38
81
SBL SEL
SBLOUT
54
83
41
46
44
L
SEL
3 1
4 2
+5V REG
IC1906
2 1
+6.5V REG
IC4001
F4001
RECT
D4001
R2 AC
R2 AC
F4002
2+1
+4.5V REG
Q3001
D–LIGHT
SYNC OUT
CN3001
BUFFER
IC3001
DIGITAL
SECTION
B
DIGITAL
SECTION
A
POWER
SECTION
D
POWER
SECTION
C
(Page 16)
(Page 20)
Ver. 1.1
STR-K1600
1616
STR-K1600
5-2. BLOCK DIAGRAM — DIGITAL SECTION —
(Page 15)
(Page 15)
• Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : DVD (DIGITAL)
• R-ch is omitted due to same as L-ch.
SDI1
SD03
DOUT
12
18
SDI2
30
GP8
AUDIO
24
XMCK
20
69
LRCKI1
15
BCKI1
17
KFSIO
CKOUT
13 22
BCKI2
BCK
14 29
LRCKI2
LRCK
15 28
CS WE
DATAO
25
SD01
23
SD02
24
SD04
26
SCKOUT
14
LRCKO
19
BCKO
20
X1502
13.9MHz
X1301
12.288MHz
MCLK1
9
MCLK2
12
CS0
44
WE0
45
68
108,107,105 -102,99,
98,80 - 77,75 - 72
24 - 27,42 - 44,
1 - 5,18 - 21
29 - 32,35 - 38,
16-13,10 - 7
112,110,109,97 - 92,
85-82,66 - 64
6 17
OE
OE0
43
41
2 11336 35 33 3432
299
37
6 74 18 19 205
EXLOCK
GP12
56
BST
ERROR
21
22
SCK15BCK11LRCK
10
95 96 97 98
38 37 36 35 47 17
INPUT
DATA
DEMODULATOR
Pa,Pb DETECTION LOCK
DETECTION
MICROPROCESSOR
I/F
C bit DETECTION
34 59
16
DVD
IN
DIGITAL
(COAXIAL)
1
VIDEO 2/
BD IN
(OPTICAL)
OUT
OPTICAL
RECEIVER
IC1351
IC1303
DIGITAL AUDIO
I/F RECEIVER
IC1301
J1301
23
WAVE
SHAPER
+1.8V
VDDI
+3.3V
VDDE
5
+3.3V
VDD
L-IN
DIGITAL DECIM. FILTER
ADC
IC1401
DSP
IC1501
SDRAM IC1502
SWITCH
IC1503
8
GP12
ERROR
1
DATAO
HACN
XRST
HDIN
PM
392
BST_SEL
HDOUT
GP9
HACN
HCS
XRST
HDINPMHDOUT
HCLK
6
CLK
CE
DI
DO
XSTATE
CLKCEDI
DO
CKSEL1
93100
48
XMODE
94
CKSEL1
XMODE
XSTATE
5
3
XOUT
DIN2
DIN0
1
SAT
IN
(OPTICAL)
OUT
OPTICAL
RECEIVER
IC1354
4
DIN1
XIN
D1301
D1503
D0-15A0-15
D0-15A0-15
SYSTEM
CONTROL
IC1101 (2/6)
TUNER/
AUDIO
SECTION
B
TUNER/
AUDIO
SECTION
A
∆Σ
MOD.
HCLK
BST
HCS
3633
1215
PCM1609 MDO
57
ADCC_INT
PCM1609 MDI
PCM1609 MC
PCM1609 ML
PCM1609/1803 RST
MDO
ML
35
13
MC
34
14
MDI
37
10
RST
GP9
DATA3
L OUT
R-CH
VOUT5
VOUT6
VOUT1
VOUT2
VOUT3
VOUT4
47
3
9
10
1
AMP
IC1403
45
46
38
SCKI
40
BCK LRCK
41
LRCKO
8CH DAC
IC1452
DAC
DATA1
SL OUT
R-CH
5
13
14
7
AMP
IC1405
DAC
VOUT7
VOUT8
31
DATA4
SBL OUT
5
3
8
7
7
AMP
IC1406
DAC
DATA2
C OUT
312
1
SW OUT
511
7
AMP
IC1404
DAC
1
2
1
L IN
R-IN
2
R IN
PDWN
7
D1501
D1502
D1504
STR-K1600
17 17
STR-K1600
5-3. BLOCK DIAGRAM — VIDEO SECTION —
1
CH1 IN1
CH2 IN2
CH2 IN1
CH3 IN2
CH3 IN1
CH1 IN2
CH2 IN3
CH3 IN3
CHI OUT
CH2 OUT
CH3 OUT
2 4
Y
P
B/CB
PR/C
R
Y
SW1 SW2
COMP_S1 COMP_S2
P
B/CB
PR/C
R
Y
P
B/CB
PR/C
R
J301
J201 (1/2)
22
75
DRIVER
6dB AMP
20
75
DRIVER
6dB AMP
18
75
DRIVER
6dB AMP
21
P.SAVE
V MUTE
13
D203 D204
10 4
13
J200 (1/2)
5
3
SAT
IN
DVD
IN
VIDEO 1
IN
VIDEO
IN
VIDEO
IN
COMPONENT
VIDEO
-1
-2
-3
-4
-5
-6
-7
-8
-9
Y
P
R/CR
PB/C
B
J302
MONITOR
OUT
COMPONENT
VIDEO
-1
1
75
DRIVER
6dB AMP
15
3 1
75
DRIVER
6dB AMP
-2
J201 (2/2)
J200 (2/2)
-2
-3
-1
VIDEO 1
DVD
SAT
-2
VIDEO
IN
-1
VIDEO
OUT
VIDEO 1
-3
VIDEO
OUT
MONITOR
+5V REG
IC807
+5V-3
3 2
-5V REG
IC804
-5V-3
COMP_S1 COMP_S2
V_SW2
V_SW4
COMP MUTE
V_SW1
COMP_S1 COMP_S2
V_SW2
V_SW4
V MUTE
V_SW1
SYSTEM CONTROL
IC1101 (3/6)
VEE
-5V-3
VCC
+5V-3
+15V
-15V
M.OUT
V1 OUT
V-1,-2
-5V-3
V+1,+2
+5V-3
V1
J298 (1/2)
9
VIDEO
-1
VIDEO 3 IN/
PORTABLE AV IN
V3
DVD
SAT
V_SW1
V_SW2
V_SW3
SW1
SW2
SW3
6
V_SW4
SW4
INPUT
SELECTOR
IC203
COMPONENT VIDEO SELECT
IC304
2
SW5
91 90 78 24 25
V_SW2
V_SW3
25 76
3
CH1 IN3
5
7 9
11
16 14 12
• Signal path : VIDEO
STR-K1600
1818
STR-K1600
5-4. BLOCK DIAGRAM — HDMI SW SECTION —
HDMI_CTRL
HDMI_PRE HDMI_OEB
HDMI_SI
SYSTEM CONTROL
IC1101 (4/6)
89 88 87 86
77
A24
DATA2+ DATA2–
DATA1+ DATA1–
DATA0+ DATA0– CLOCK+ CLOCK–
SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER
DATA2+ DATA2–
DATA1+ DATA1–
DATA0+ DATA0– CLOCK+ CLOCK–
SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER
DATA2+ DATA2–
DATA1+ DATA1–
DATA0+ DATA0– CLOCK+ CLOCK–
SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER
CN5001
DVD IN
4 6
1 3
7
9 10 12 15 16 19 13 18
B24 A23
B23 A22 B22 A21 B21 SCL2
76 74 73 71 70 68 67 64
15
A14 B14 A13
B13 A12 B12 A11 B11
OEB
S1
14 12 11 9 8 6 5
SCL1 SDA1
3 2
HPD1
80
25
Y4 Z4 Y3
Z3 Y2 Z2 Y1 Z1
26 28 29 31 32 34 35
SCL SINK SDA SINK
38 39
HPD SINK
40
SDA2 HPD2
63 62
CN5002
4
6
1
3
7
9 10 12 15 16 19 13 18
CN5003
4
6
1
3
7
9 10 12 15 16 19 13 18
1
LEVEL SHIFT
IC5004
HDMI RECEIVER/TRANSCEIVER
IC5001
ANALOG SWITCH
IC5005
5
4 5
3
7
1
6
3
4
42
21
1
POWER
CONTROL
4 2
1
+5.8V
REG
3 1
+3.3V
REG
IC5003
IC5006
HDMI+3.3V
+7V
IC5002
OUT
VIDEO 2/BD IN
HDMI
STR-K1600
19 19
STR-K1600
5-5. BLOCK DIAGRAM — KEY/DISPLAY SECTION —
83
FL DISPLAY DRIVER
IC100
14
I
29
31
82
29
30
5
6
65 64
54
SW NETWORK
S101-108
RV102
MASTER
VOLUME
56
51 49
28 27
77
+3.3V
(STBY)
X1
X0
SDA
38
ADCC
SCL
POWER_KEY
FLASH1/C LINK_TX FLASH2/C LINK_RX MD2 MD0
RSTX
SDA
SCL
EEPROM
IC1131
X1101
24MHz
SIRCS
F1 F2
17
FL_DATA
7
DIN
9
FL_LAT
9
STB
16
FL_CLK
8
1
CLK
GRID1
I
GRID11
SW1
SEG1
I
SEG17
VOL_ENCODER(A) VOL_ENCODER(B)
ENC_A ENC_B
A/D2
SW NETWORK S109–113,115
A/D1
2
3
21 22
RV103
– TUNING +
TUNING_A TUNING_B
2
3
31 32
RV101 INPUT
SELECTOR
2
3
2
REMOTE
CONTROL
SIGNAL
RECEIVER
IC103
OUT
SIRCS
SYSTEM
CONTROL
IC1101 (5/6)
BUFFER
IC101
CNS504
S100
FLASH2 MD2 MD0 RESET
1 2
SDA
SCL FLASH1
9 8
7 6 5
FLASH
PROGRAMMING
12
I
/
I
39
40
FL101
VACUUM
FLUORESCENT
DISPLAY
IC1111 RESET
42
I
32
9
4
2
8
6
3
15
MIC AMP
IC2000
DETECT
D2013,2014
LED
DRIVER
Q110
MULTI
CHANNEL
DECODING
D105
AUTO CAL MIC
J2000
STR-K1600
2020
STR-K1600
5-6. BLOCK DIAGRAM — POWER SECTION —
(Page 15)
8
12 11
DRIVE
POWER AMP
Q701-704
CURRENT
DETECT
Q705,706
RY701
D729
PRE DRIVER
IC701
IN 2
+VOUT2
-VOUT2
R
L
L
AUDIO
OUT
SUB
WOOFER
CENTER
SURROUND
BACK
SURROUND
R
R-CH
R-CH
L-CH
R-CH
SL-CH
C-CH
R-CH
SR-CH R-CH
TUNER/
AUDIO
SECTION
C
TUNER/ AUDIO
SECTION
D
RY901
D804
D1001
F1
F2
-20V
+3.3V
(STBY)
+1.8V
+5V
-7V
+7V
TU+9V
-20V
RECT
D910-913
D914 D915
D1107
D1110
OVERLOAD
DETECT
D740,Q740
8
61
12 11
DRIVE
POWER AMP
Q501-504
CURRENT
DETECT
Q505,506
-20V REG Q801
B-SWITCH
Q691,692
RELAY DRIVER
Q901
AC IN
DETECT
Q921
PRE DRIVER
IC501
IN 2
+VOUT2
-VOUT2
OVERLOAD
DETECT
D540,Q540
8
12 11
DRIVE
POWER AMP
Q651-654
CURRENT
DETECT
Q655,656
PRE DRIVER
IC601
IN 2
+VOUT2
-VOUT2
OVERLOAD
DETECT
D640,Q640
D529
RY601
RY560
PROTECTOR D721,722,732,733 Q723,725,793,795
58
48
66
D1111
D1108
+9V
(STBY)
OVERLOAD
DETECT AMP
72
IC691
–45V
-B
+3.3V/+1.8V
REG
4
5
+3.3V
2
IC1903
+A5V
+5V REG
13
IC1001
+3.3V
REG
13
IC1904
+9V REG
13
IC1902
-15V
+15V
+7V REG
31
IC801
-7V
REG
23
IC802
+5V REG
13
IC1031
+B
R-CH
R-CH
R-CH
R-CH
R-CH
R-CH R-CH
RECT D802
RECT
D920-923
RECT
D805-808
T901
POWER
TRANSFORMER
TB001 (2/2)
TB001 (1/2)
TM603
J408
(MAIN)
FRONT
RY791
PHONES
J790
R-CH
FRT A RY
HP RY
VACS CTRL
C/SUR RY
SW RY
HP DETECT
FRONT_A_RY
PROTECTOR
HP DETECT
STOP
45
HP_RY
VACS CTRL
62
POWER_RY
70
SW_RY
69
C/REAR/SB_RY
FRT A RY
HP DETECT
HP RY
55
VACS CTRL
SW RY
C/SUR RY
SYSTEM CONTROL
IC1101 (6/6)
PRE
DRIVE
PRE
DRIVE
SW-CH
-45V +B
SBL-CH
6
2 3
DRIVE
POWER AMP
Q533,534
571,572
CURRENT
DETECT
Q535,536
IN 1
+VOUT1
-VOUT1
OVERLOAD
DETECT
D580,Q580
PRE
DRIVE
-45V +B
-45V +B
PRE
DRIVE
R810
R2 AC
R2 AC
R811
R910
SPEAKERS
IMPEDANCE
USE 6-16
RELAY
DRIVER
Q610
RY610
RELAY
DRIVER
Q612
RELAY DRIVER
Q560
RELAY
DRIVER
Q710
RELAY
DRIVER
Q790
T902
POWER
TRANSFORMER
(SUB)
AC IN ~
F901
JW795
S901
-3
-2
-1
EXCEPT
E51 MODEL
E51 MODEL
S901
120V
220V
240V
VOLTAGE
SELECTOR
JW905
JW903
EXCEPT E51,MX MODEL
MX
MODEL JW906
JW900
• Signal path : TUNER (FM/AM)
• R-ch is omitted due to same as L-ch.
Abbreviation
E51 : Chilean and Peruvian models MX : Mexican model
(Page 15)
Ver. 1.1
STR-K1600
21 21
STR-K1600
for schematic diagram:
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in and 1/
4
W or less unless otherwise
specified.
•f: internal component.
2 : nonflammable resistor.
5 : fusible resistor.
C : panel designation.
A : B+ Line.
B : B– Line.
•Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM
•Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal produc­tion tolerances.
•Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc­tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER (FM/AM) L : VIDEO (AUDIO) I : VIDEO J : DVD (DIGITAL) c : CD (ANALOG)
• Abbreviation AUS : Australian model MY : Malaysia model SP : Singapore model TH : Thai model AR : Argentina model E51 : Chilean and Peruvian models MX : Mexican model
for printed wiring boards:
X : parts extracted from the component side.
•f: internal component.
: Pattern from the side which enables seeing.
Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated.
C
B
These are omitted.
E
Q
B
These are omitted.
C
Q
Q
E
BCE
• Abbreviation AUS : Australian model MY : Malaysia model SP : Singapore model TH : Thai model E51 : Chilean and Peruvian models MX : Mexican model
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
• Waveforms — DIGITAL Board —
1
IC1301 qd (CKOUT)
3.8 Vp-p
3.1 Vp-p
1V/DIV, 50nsec/DIV
3
IC1301 wa (XOUT)
1V/DIV, 50nsec/DIV
4
IC1501 9 (MCLK1)
2.2 Vp-p
1V/DIV, 50nsec/DIV
2
IC1301 qf (BCK)
3.6 Vp-p
1V/DIV, 0.2µs/DIV
13.9 MHz
12.288 MHz
3.07 MHz
12.288 MHz
5
IC1501 qs (MCLK2)
3.2 Vp-p
2.2 Vp-p
1V/DIV, 50nsec/DIV
7
IC1101 id (X1)
1V/DIV, 50nsec/DIV
6
IC1501 qf (SCKOUT)
3.5 Vp-p
1V/DIV, 50nsec/DIV
24 MHz
12.288 MHz
13.9 MHz
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety. Replace only with part number specified.
Ver. 1.1
Loading...
+ 47 hidden pages