Sony STRDE-697 Service manual

STR-DE697
SERVICE MANUAL
Ver 1.1 2004. 10
Photo: Black type
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.
SPECIFICATIONS
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC
DISTORTION: (Models of area code US only)
With 8 ohm loads, both channels driven, from 20 – 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than
0.09 % total harmonic distortion from 250 milliwatts to rated output.
Amplifier section
Power Output
Models of area code US, CND Rated Power Output at Stereo Mode (8 ohms 20 Hz – 20 kHz, THD 0.09 %)
Reference Power Output (8 ohms 20 Hz – 20 kHz, THD 0.09 %)
(8 ohms 1 kHz, THD 0.7 %)
90 W + 90 W
1)
FRONT CENTER SURR SURR BACK
FRONT CENTER SURR SURR BACK
2)
: 90 W/ch
2)
: 90 W
2)
: 90 W/ch
2)
: 100 W/ch
2)
: 100 W
2)
: 100 W/ch
1)
2)
: 90 W/ch
2)
: 100 W/ch
Models of area code AEP, UK Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %)
Reference Power Output (8 ohms 1 kHz, THD 0.7 %)
Models of area code SP, MY Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %)
Reference Power Output (8 ohms 1 kHz, THD 10 %)
100 W + 100 W
1)
FRONT CENTER SURR SURR BACK
100 W + 100 W
1)
FRONT CENTER SURR SURR BACK
2)
: 100 W/ch
2)
: 100 W
2)
: 100 W/ch
2)
: 120 W/ch
2)
: 120 W
2)
: 120 W/ch
1)
2)
: 100 W/ch
1)
2)
: 120 W/ch
– Continued on next page –
9-877-763-02
2004J04-1 © 2004. 10
Sony Corporation
Audio Group Published by Sony Engineering Corporation
1
STR-DE697
Models of area code AUS Rated Power Output at Stereo Mode (8 ohms 20 Hz – 20 kHz, THD 0.09 %)
80 W + 80 W
(8 ohms 1 kHz, THD 0.7 %)
100 W + 100 W
Reference Power Output
1)
(8 ohms 20 Hz – 20 kHz, THD 0.09 %)
FRONT CENTER SURR SURR BACK
(8 ohms 1 kHz, THD 0.7 %)
FRONT CENTER SURR SURR BACK
(8 ohms 1 kHz, THD 10 %)
FRONT CENTER SURR SURR BACK
2)
: 80 W/ch
2)
: 80 W
2)
: 80 W/ch
2)
: 100 W/ch
2)
: 100 W
2)
: 100 W/ch
2)
: 120 W/ch
2)
: 120 W
2)
: 120 W/ch
1)
1)
2)
: 80 W/ch
2)
: 100 W/ch
2)
: 120 W/ch
1) Measured under the following conditions: Area code Power requirements
US, CND 120 V AC, 60 Hz AEP, UK, SP, MY 230 V AC, 50 Hz AUS 240 V AC, 50 Hz
2) Depending on the sound field settings and the source, there may be no sound output.
Frequency response MULTI CH IN, SA-CD/ 10 Hz – 70 kHz
CD, MD/TAPE, DVD, +0.5/–2 dB (with sound AUX, VIDEO 1, 2, 3 field and equalizer
bypassed)
Inputs (Analog) MULTI CH IN, SA-CD/ Sensitivity: 500 mV
CD, MD/TAPE, DVD, Impedance: 50 kiloohms AUX, VIDEO 1, 2, 3 S/N
3)
: 96 dB
(A, 500 mV
4)
)
3) INPUT SHORT (with sound field and equalizer bypassed).
4) Weighted network, input level.
Inputs (Digital) DVD, SA-CD/CD Sensitivity: –
(Coaxial) Impedance: 75 ohms
S/N: 100 dB (A, 20 kHz LPF)
VIDEO 2, MD/TAPE, Sensitivity: – SA-CD/CD (Optical) Impedance: –
S/N: 100 dB (A, 20 kHz LPF)
Outputs (Analog) MD/TAPE (OUT), Voltage: 500 mV
VIDEO 1 (AUDIO OUT) Impedance: 10 kiloohms SUB WOOFER V oltage: 2 V
Impedance: 1 kiloohms
Outputs (Digital) MD/TAPE (Optical) Sensitivity: –
EQ Gain levels ±6 dB, 1 dB step
FM tuner section
Tuning range 87.5 – 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo: 38.3 dBf, 22.5 µV/75 ohms Useable sensitivity 11.2 dBf, 1 µV/75 ohms S/N
Mono: 76 dB
Stereo: 70 dB Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5% Separation 45 dB at 1 kHz Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range
Models of area code US, CND
With 10-kHz tuning scale: 530 – 1,710 kHz
With 9-kHz tuning scale: 531 – 1,710 kHz
Models of area code AEP, UK, AUS, SP, MY
With 9-kHz tuning scale: 531 – 1,602 kHz Antenna Loop antenna Intermediate frequency 450 kHz Usable sensitivity 50 dB/m (at 1,000 kHz or
999 kHz) S/N 54 dB (at 50 mV/m) Harmonic distortion 0.5 % (50 mV/m, 400 Hz) Selectivity
At 9 kHz: 35 dB At 10 kHz: 40 dB
5) You can change the AM tuning scale to 9 kHz or 10 kHz.
After tuning in any AM station, turn of f the receiv er . While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.
5)
5)
2
STR-DE697
1.5 k
0.15 µF
AC voltmeter (0.75 V)
To Exposed Metal Parts on Set
Earth Ground
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms COMPONENT VIDEO: (Except for models of area code AEP, UK)
Y: 1 Vp-p, 75 ohms
PB/CB/B-Y: 0.7 Vp-p,
75 ohms
PR/CR/R-Y: 0.7 Vp-p,
75 ohms 80 MHz HD Pass Through
General
Power requirements Area code Power requirements
US, CND 120 V AC, 60 Hz AEP, UK 230 V AC, 50/60 Hz AUS 240 V AC, 50 Hz SP, MY 220 – 230 V AC, 50/60 Hz
Power consumption Area code Power consumption
US 250 W CND 340 V A AEP, UK, AUS, SP, MY 265 W
Power consumption (during standby mode)
0.3 W (when “P.SAVE.” in the
CUSTOMIZE menu is set to
“ON”)
AC outlets Area code AC outlets
US, CND 1 switched, 120 W/1A MAX AEP, UK, AUS, SP, MY 1 switched, 100 W MAX
Dimensions (w/h/d) (Approx.)
430 × 157.5 × 312 mm
(16 7/8 × 6 2/8 × 12 2/8
inches) including
projecting parts and
controls
Mass (Approx.) 8.5 kg (18 lb 12 oz)
Supplied accessories
FM wire antenna (1) AM loop antenna (1) Remote commander RM-PP413 (1) R6 (size-AA) batteries (2)
Design and specifications are subject to change without notice.
•Abbreviation CND : Canadian model AUS: Australian model SP : Singapore model MY : Malaysia model
SAFETY CHECK-OUT (US MODEL)
After correcting the original service problem, perform the follow­ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica­tion is 0.75 V, so analog meters must have an accurate low­voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex­amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit­able. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
STR-DE697
MODEL IDENTIFICATION
— BACK P ANEL —
Part No.
MODEL PART No.
US 4-252-501-0s CND 4-252-501-1s AEP 4-252-501-2s UK 4-252-501-3s SP, MY 4-252-501-4s AUS 4-252-501-5s
•Abbreviation CND: Canadian model AUS: Australian model SP : Singapore model MY : Malaysia model

TABLE OF CONTENTS

1. GENERAL
Main unit ................................................................................. 5
Remote button description....................................................... 6
2. DISASSEMBL Y
2-1. Case .....................................................................................7
2-2. Front Panel Section ............................................................. 8
2-3. Back Panel Section.............................................................. 8
2-4. Digital Board ....................................................................... 9
2-5. Standby Board ..................................................................... 9
2-6. Main Board ....................................................................... 10
2-7. Surr Back Board ................................................................ 10
3. TEST MODE ..................................................................... 11
4. DIAGRAMS
4-1. IC Pin Descriptions ........................................................... 12
4-2. Circuit Boards Location .................................................... 15
4-3. Block Diagram – Tuner/Audio Section –.......................... 16
4-4. Block Diagram – Digital Section – ................................... 17
4-5. Block Diagram – Video Section – ..................................... 18
4-6. Block Diagram – Key/Display Section – .......................... 19
4-7. Block Diagram – Power Section – .................................... 20
4-8. Printed Wiring Boards – Main Section – .......................... 22
4-9. Schematic Diagram – Main Section (1/2) – ...................... 23
4-10. Schematic Diagram – Main Section (2/2) – ...................... 24
4-11. Printed Wiring Board – Digital Section (1/2) – ................ 25
4-12. Printed Wiring Board – Digital Section (2/2) – ................ 26
4-13. Schematic Diagram – Digital Section (1/3) – ................... 27
4-14. Schematic Diagram – Digital Section (2/3) – ................... 28
4-15. Schematic Diagram – Digital Section (3/3) – ................... 29
4-16. Printed Wiring Boards –
Center/Surround Back Speaker Section – ......................... 30
4-17. Schematic Diagram –
Center/Surround Back Speaker Section – ......................... 31
4-18. Printed Wiring Board – Video Section –........................... 32
4-19. Schematic Diagram – Video Section –.............................. 33
4-20. Printed Wiring Board – S-video Section – ........................ 34
4-21. Schematic Diagram – S-video Section –........................... 34
4-22. Printed Wiring Boards – Display Section – ...................... 35
4-23. Schematic Diagram – Display Section –........................... 36
4-24. Printed Wiring Boards – Power Section – ......................... 37
4-25. Schematic Diagram – Power Section – ............................. 38
4-26. IC Block Diagrams............................................................ 39
5. EXPLODED VIEWS
5-1. Case Section ...................................................................... 42
5-2. Front Panel Section ........................................................... 43
5-3. Back Panel Section............................................................ 44
5-4. Chassis Section ................................................................. 45
6. ELECTRICAL PARTS LIST ........................................ 46
4
SECTION 1

GENERAL

STR-DE697
This section is extracted from instruction manual.
5
STR-DE697
6
SECTION 2
)

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.
SET
2-1. CASE
(Page 7)
STR-DE697
2-2. FRONT PANEL SECTION
(Page 8)
2-5. STANDBY BOARD
(Page 9)
2-3. BACK PANEL SECTION
(Page 8)
2-4. DIGITAL BOARD
(Page 9)
2-6. MAIN BOARD
(Page 10)
Note : Follow the disassembly procedure in the numerical order given.
2-1. CASE
1
two screws
(case 3 TP2)
2-7. SURR BACK BOARD
(Page 10)
2
three screws
(case 3 TP2
3
4
two screws
(case 3 TP2)

case

7
STR-DE697
2-2. FRONT P ANEL SECTION
6
two screws
(+BVTP 3 x 8)
4
2
CNP791
two screws
(+BVTP 3 x 8)
1
clip
2-3. BACK PANEL SECTION
6
CNP502
7
8

front panel section

9
CN908
qa
CNP901
CNP501
0
CN906
5
four screws
(+BVTP 3 x 8)
qs
three screws
(+BVTP 3 x 8)
qf
7
CN201
3
CNS505
two screws
(+BVTP 3 x 8)
qg
three screws
(+BVTP 3 x 8)
qh
six screws
(+BVTP 3 x 8)
qj
five screws
(+BVTP 3 x 8)
8
CNP913
qd
screw
(+BVTP 3 x 8)
3
CNP203
qk

back panel section

4
CNP202
1
CNS201
5
CNP503
2
connector
8
2-4. DIGIT AL BOARD
3
8
screw
(+BVTP 3 x 8)
CNP507
2
CNP510
1
CNP506
5
0

DIGITAL board

7
CNP501
CNP500
6
9
bracket (digital)
STR-DE697
2-5. ST ANDBY BOARD
5
three screws
(+BV SUMITITE (B3))
4
CNP903
3
CNP902
2
CNP804
1
CNP915
6

STANDBY board

4
screw
(+BVTP 3 x 8)
9
STR-DE697
s
2-6. MAIN BOARD
5
screw
(+BV SUMITITE (B3))
3
two screws
(+BV SUMITITE (B3))
1
CNP915
2
CNP802
4
two screws
(+BV SUMITITE (B3))
6
two screws
(+BV SUMITITE (B3))
7

MAIN board

2-7. SURR BACK BOARD
8

SURR BACK board

6
bracket (SUR)
1
CNP572
5
two screws
(+BVTP 3 x 8)
3
three screws
(transistor)
2
CN573
7
bracket (SUR)
4
three screw
(transistor)
10
SECTION 3

TEST MODE

STR-DE697
FACTORY PRESET MODE
* All preset contents are reset to the default setting. * Procedure:
While depressing the [FM MODE] and the [DISPLAY] buttons simultaneously, press the
?/1 button to turn on the main power .
The message “FA CT OR Y” appears for a moment and the present contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Press the [TUNER FM/AM] button to set AM and press the ?/1 button to turn off the main power. While depressing the [PRESET TUNING +] button or the [TUNING +] button, press the ?/1 button to turn on the main power. Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step.
SPEAKER SIZE SELECTION MODE
* Either the normal speaker or micro satellite speaker can be se-
lected.
* Procedure:
While depressing the [DIMMER] button, press the ?/1 button to turn on the main power. Either the message “NORM. SP .” or “MICRO SP . ” appear s for a moment and select the desired speaker size.
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING ---] and the [SPEAKERS $OFF/A/ B/A+B%] buttons simultaneously , press the the main power.
1. ALL segments light on.
SP A
D
D
LFE
SW
CR
L
SL S SR
SBL SB SBR
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
[2CH], [A.F.D.], [MOVIE], [MUSIC] and [MULTI CHANNEL DE­CODING] LED light on.
2. Press the [VIDEO 1] button, confirm display.
SP A
D
D
LFE
LSWR
S
SB
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
[A.F.D.] and [MUSIC] LED light on.
?/1 button to turn on
MEMORY
kHz mft.
MHz
kHz mft. MHz
DIRECT
dB
MEMORY
DIRECT
dB
D.RANGE EQ STEREO MONO
D.RANGE EQ STEREO MONO
4. Press the [VIDEO 1] button, all segments and all LEDs light off.
5. Every pressing the [VIDEO 1] button turns on each segment and LED one after another in the same order. (Not only the [VIDEO 1] button, b ut also the other b uttons such as [VIDEO 2], [VIDEO 3], [DVD], [MD/TAPE], [SA-CD/CD], [TUNER FM/AM] and [AUX] can be used.)
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn on the main power. The message “SF. CLR.” appears for a moment and initializa­tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed. * Procedure:
While depressing the [TUNING ---] and the [DISPLAY] buttons simultaneously, press the ?/1 button to turn on the main po wer . The model name, destination and the software version are dis­played for a moment.
KEY CHECK MODE
* Button check * Procedure:
While depressing the [TUNING ---] and the [MAIN MENU] buttons simultaneously, press the ?/1 button to turn on the main po wer . Either the message “REST 28” appears. Every pressing of any button other than the
?/1 counts down
the buttons. The buttons which are already counted once are not counted again. When all buttons are pr essed “REST 00” appears.
AUTOBETICAL MODE (AEP, UK model only)
* When this mode is used, the receiver scans the broadcasts that
can be received by the tuner, and sets up the broadcasts. Be sure to start scanning after connecting the antenna.
* Procedure:
Check that the antenna is connected. While depressing the [MEMORY] button, press the ?/1 button to turn on the main power. The message “AUTO-BETICAL SELECT” appears for a mo­ment and the receiver starts scanning.
COMMAND MODE SELECTION MODE
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [ENTER] button, press the ?/1 button to turn on the main power. Either the message “C.MODE.AV 1” or “C.MODE.AV 2” ap­pears for a moment and select the desired mode.
3. Press the [VIDEO 1] button, confirm display.
SP A
D
D
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
D.RANGE EQ STEREO MONO
kHz mft. MHz
C
SL SR
SBL SBR
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
[2CH], [MOVIE] and [MULTI CHANNEL DECODING] LED light on.
MEMORY
DIRECT
11
STR-DE697
SECTION 4 DIAGRAMS
4-1. IC PIN DESCRIPTIONS
• IC1501 CXD9718Q (DSP) (DIGITAL Board (2/3))
Pin No. Pin Name I/O Pin Description
1 VSS Ground 2 XRST I Reset signal input from SYSTEM CONTROL IC 3 EXTIN I Not used (Connect to ground) 4 LRCKI3 I Not used (Connect to ground) 5 VDDI I Power supply pin (+2.6 V) 6 BCKI3 I Not used (Connect to ground) 7 PLOCK O Not used (Open) 8 VSS Ground
9 MCLK1 I Clock signal input (13.5 MHz) 10 VDDI I Power supply pin (+2.6 V) 11 VSS Ground 12 MCLK2 O Clock signal output (13.5 MHz) 13 MS I Not used (Fixed at L) 14 SCKOUT O Internal system clock signal output for 2CH/6CH DAC IC 15 LRCKI1 I Sampling clock signal input from ADC IC 16 VDDE I Power supply pin (+3.3 V) 17 BCKI1 I Bit clock signal input from ADC IC 18 SDI1 I Audio IF data input from ADC IC 19 LRCKO O Sampling clock signal output for 2CH/6CH DAC IC 20 BCKO O Bit clock signal output for 2CH/6CH DAC IC 21 VSS Ground 22 KFSIO I/O Audio clock signal (384fs/256fs) input/output for DIR IC
23 to 25 SDO1 to SDO3 O Digital audio serial data output for 6CH DAC IC
26 SDO4 O Digital audio serial data output for 2CH DAC IC 27 SPDIF O Not used (Open) 28 LRCKI2 I Sampling clock signal input from ADC IC 29 BCKI2 I Bit clock signal input from ADC IC 30 SDI2 I Digital audio serial data input from DIR IC 31 VSS Ground 32 HACN O Acknowledge signal output for SYSTEM CONTROL IC 33 HDIN I Serial data input from SYSTEM CONTROL IC 34 HCLK I Clock signal input from SYSTEM CONTROL IC 35 HDOUT O Serial data output for SYSTEM CONTROL IC 36 HCS I Chip select signal input from SYSTEM CONTROL IC 37 GP12 I GP12 signal input from SYSTEM CONTROL IC
38, 39 GP13, GP14 O Not used (Open)
40 VDDI I Power supply pin (+2.6 V) 41 VSS Ground 42 GP15 O Not used (Open) 43 OE0 O Not used (Open) 44 CS0 O External memory chip select signal output for D/A converter IC (SRAM) 45 WE0 O SRAM write enable signal output for D/A converter IC 46 VDDE I Power supply pin (+3.3 V) 47 WMD1 I Not used (Fixed at H) 48 VSS Ground 49 WMD0 I Not used (Fixed at H) 50 PAGE2 O Not used (Open) 51 VSS Ground
52, 53 PAGE1, PAGE0 O Not used (Open)
54 BOOT I Not used (Connect to ground) 55 TST1 O Not used (Open)
12
STR-DE697
Pin No. Pin Name I/O Pin Description
56 BST I Boot stop signal input from SYSTEM CONTROL IC 57 MOD1 I Operation mode signal input (L: 386fs, H: 256fs) (Fixed at H) 58 MOD0 I Operation mode signal input (L: single chip mode, H: use prohibited) (Fixed at L) 59 EXLOCK I Error detection signal input from DIR IC 60 VDDI I Power supply pin (+2.6 V) 61 VSS Ground
62, 63 A17, A16 O Not used (Open)
64 to 66 A15 to A13 O External memory address signal output for D/A converter IC (SRAM)
67 GP10 O Not used (Open) 68 GP9 O GP9 signal output for SYSTEM CONTROL IC 69 GP8 I Audio signal input from DIR IC 70 VDDI I Power supply pin (+2.6 V) 71 VSS Ground
72 to 75 D15/GP7 to D12/GP4 I/O External memory data input/output for D/A converter IC (general port)
76 VDDE I Power supply pin (+3.3 V)
77 to 80 D11/GP3 to D8/GP0 I/O External memory data input/output for D/A converter IC (general port)
81 VSS Ground 82 A9 O External memory address signal output for D/A converter IC (SRAM)
83 to 85 A12 to A10 O External memory address signal output for D/A converter IC (SRAM)
86 TDO O Not used (Fixed at H) 87 TMS I Not used (Fixed at H) 88 XTRST I Not used (Fixed at H) 89 TCK I Not used (Fixed at H) 90 TDI I Not used (Fixed at H) 91 VSS Ground
92 to 97 A8 to A3 O External memory address signal output for D/A converter IC (SRAM)
98, 99 D7, D6 I/O External memory data input/output for D/A converter IC (SRAM)
100 VDDI I Power supply pin (+2.6 V) 101 VSS Ground
102 to 105 D5 to D2 I/O External memory data input/output for D/A converter IC (SRAM)
106 VDDE I Power supply pin (+3.3 V) 107, 108 D1, D0 I/O External memory data input/output for D/A converter IC (SRAM) 109, 110 A2, A1 O External memory address signal output for D/A converter IC (SRAM)
111 VSS Ground
112 A0 O External memory address signal output for D/A converter IC (SRAM)
113 PM I PLL initialization signal input from SYSTEM CONTROL IC 114, 115 SDI3, SDI4 I Not used (Open)
116 SYNC I Sync/async select signal input (L: sync, H: async) (Fixed at H)
117 TST2 I Not used (Connect to ground)
118 GP11 I Not used (Connect to ground)
119 TST3 I Not used (Connect to ground)
120 VDDI I Power supply pin (+2.6 V)
13
STR-DE697
• IC1101 MB90478PF-G-183-BND (SYSTEM CONTROL) (DIGITAL Board (3/3))
Pin No. Pin Name I/O Pin Description
1DATAO I Serial data line signal input from DIR IC 2GP9 I GP9 signal input from DSP IC 3 BST O Boot stop control signal output for DSP IC 4 HCS O Chip select signal output for DSP IC 5HACNIAcknowledge signal input from DSP IC 6 XRST O Reset signal output for DSP IC 7PMOPLL control signal output for DSP IC 8 GP12 O GP12 signal output for DSP IC
9 AK5380_PDN O Power down signal output for ADC IC 10 AK4355_CSN O Chip select signal output for 6CH DAC IC 11 VSS Ground 12 AK4355_PDN O Power down signal output for 6CH DAC IC 13 AK4381_PDN O Power down signal output for 2CH DAC IC 14 AK4381_CSN O Chip select signal output for 2CH DAC IC 15 AK4355_CLK O Clock signal output for 2CH/6CH DAC IC
16
17
18 HDOUT I Serial data input from DSP IC 19 HDIN O Serial data output for DSP IC 20 HCLK O Serial data clock signal output for DSP IC 21 AK4355_CDT1 O CDT1 signal output for 2CH/6CH DAC IC 22 VOL_LATCH O Latch signal output for FUNCTION SELECT IC 23 VCC5 Power supply pin (+3.3 V) 24 SYS_MUTE O System mute control signal output 25 ANA/DIG O Muting and error port signal output 26 FL_CLEAR O Not used (Open) 27 FLASH2 Flash programming signal output 2 28 FLASH1 Flash programming signal output 1 29 ENC_A I –/+ (cursor) encoder (+) signal input 30 ENC_B I –/+ (cursor) encoder (–) signal input
31, 32 F_A, F_B Not used (Fixed at L)
33 SCL O Clock signal output for EEPROM IC 34 SDA I/O Serial data input/output for EEPROM IC 35 AVCC Power supply pin (+3.3 V) 36 AVRH Power supply pin (+3.3 V) 37 AVSS Ground
38 to 40 A/D0 to A/D2 I Key signal input (A/D port)
41 VERSION I 42 VSS Ground
43 RDS_SIG I RDS signal level input (AEP, UK model only) 44 MODEL I Model detection signal input 45 VOL_ENC (A) I Volume encoder (+) signal input 46 VOL_ENC (B) I Volume encoder (–) signal input 47 BLUE_LED O LED (MULTI CHANNEL DECODING) driver signal output 48 STOP I AC off detection signal input 49 MOD0 Selection of micon operation mode 50 MOD1 Not used (Connect to AVCC) 51 MOD2 Selection of micon operation mode 52 RDS_CLK I RDS data clock signal input (AEP, UK model only)
(VOL_TUNER_TC9273)
(VOL_TUNER_TC9273)
IC_CLK
IC_DATA
O Clock signal output for FUNCTION SELECT IC and tuner pack
O Serial data signal output for FUNCTION SELECT IC and tuner pack
Destination detection signal input (Fixed at L: US, Canadian model, H: Except for US, Canadian model)
14
STR-DE697
DIGITAL board
POWER board
STANDBY board
BRIDGEABLE board
VIDEO board
S-VIDEO board
SURR BACK board
SPEAKER board
MAIN board
TUNING board
VIDEO3 board
HEADPHONE board
DISPLAY board
Pin No. Pin Name I/O Pin Description
53 RDS_DATA I RDS data input (AEP, UK model only) 54 SIRCS I SIRCS signal input 55 HP_DETECT I Headphones detection signal input 56 POWER_KEY I Power key detection signal input 57 FL_LAT O Latch signal output for FL driver IC 58 POWER_RY O Power relay driver control signal output 59 FL_DATA O Serial data output for FL driver IC 60 FL_CLK O Clock signal output for FL driver IC 61 PROTECTOR I Protector detection signal input 62 HP_RY O Headphones relay driver control signal output 63 FUSE_DETECT I Fuse open detection signal input 64 A1_OUT O CTRL A1 II signal output (Except for AEP, UK model) 65 A1_IN I CTRL A1 II signal input (Except for AEP, UK model) 66 FRONT_RY O Front speaker A relay driver control signal output 67 SP_B_RY O Front speaker B relay driver control signal output 68 C/SB_RY O Center/Surround back speakers relay driver control signal output 69 REAR_RY O Surround speaker relay driver control signal output 70 SW_RY O Sub woofer relay driver control signal output 71 NC Not used (Fixed at L) 72 BRIDGEABLE_RY O Bridgeable relay driver control signal output 73 D0 I Tuner serial data input 74 SLATCH O Tuner latch signal output 75 TUNED I Tuned signal detection input 76 STEREO I Stereo signal detection input 77 RSTX I Reset signal input 78 MUTE O Tuner mute signal output 79 X1A Not used (Open) 80 X0A Not used (Connect to VSS) 81 VSS Ground 82 X0 Clock signal input (16 MHz) 83 X1 Clock signal output (16 MHz) 84 VCC3 Power supply pin (+3.3 V) 85 GROUPING_SW Not used (Open)
86 to 89 SW1 to SW4 O Video select signal output
90 SELECT2 O Digital input select 2 signal output 91 SELECT1 O Digital input select 1 signal output 92 BST_SEL O 96/24 signal output for DSP IC 93 XMODE O Xmode signal output for DIR IC 94 CKSEL1 O Clock select signal output for DIR IC 95 CLK O Data clock signal output for DIR IC 96 CE O Latch signal output for DIR IC 97 DI O Data output for DIR IC 98 DO I Data input from DIR IC 99 ERROR I Error detection signal input from DIR IC
100 XSTATE I Xstate signal input from DIR IC
4-2. CIRCUIT BOARDS LOCA TION
15 15
STR-DE697
4-3. BLOCK DIAGRAM — TUNER/AUDIO SECTION —
AEP,UK MODEL
AEP,UK MODEL
EXCEPT
AEP,UK MODEL
ANTENNA
FM 75
COAXIAL
TU+10V
TU+3.3V
3.3V
(STBY)
AM
TN1
FM/AM TUNER UNIT
L-CH
RDS DATA
RDS INT
FM SIG OUT
R-CH
STEREO
TUNED
MUTING
CE
DO
DATA
CLOCK
3.3V
SA-CD/CDINMD/TAPE
AUX
IN
R-CH
RDS DATA
53
RDS CLK
52
RDS SIG
43
76
STEREO
75
TUNED
78
MUTE
S LATCH
74 73
DO
SW RY
70
R-CH
LR
FRONT
L
LR
SURROUND
MULTI CH IN
LR
-1 -2 -5 -6
J400 J403 J298(2/2) J404
R-CH
J401
-1 -2 -3 -4 -5 -6
R
R-CH
OUT
LR
R-CH
CENTER
R-CH
IC.DATA
IC.CLK
VOL LATCH
SYSTEM
CONTROL
IC1101 (1/4)
SUB
WOOFER
MD/TAPEINDVD AUDIO
LRLR
-1 -2 -3 -4
16 17 22
R-CH
IN
R-CH
AUDIO
LR
-2 -3-3 -4
R-CH
DIGITAL
SECTION
(Page 17)
R-CH R-CH
DIR
FUNCTION SELECT
SW SEL
IC401
C
SEL
SEL
L
SEL
SL
61
4
65 72 74
SEL SW
76 78 80
18
MCU
20
I/F
19
57
54
55
56 53
R-CH
58
R-CH
52
51
SBL OUT
SW OUT
C OUT
C
SL OUT
L OUT
SBL SEL
R-CH
15 11 12 13 10
REG
Q471
21 24 22
DVDD
R-CH
R-CH
R-CH
R-CH
R-CH
R-CH
R-CH
+7V
+7V-7V
AVCCAVEE
63
62
68
67 70 69
6
7
46
47
40
41
35
34
28
29
Q379
VIDEO 1
AUDIO OUT AUDIO INAUDIO IN
L
RL
-3 -4 -5 -6
MUTE
Q300,310
MUTE
Q320,330
MUTE
Q350
MUTE
Q340
MUTE
Q360,370
SYSTEM MUTE
VIDEO 2
RLR
-1 -2
5 7
SUB WOOFER
AMP
IC402
DIGITAL
B
SECTION
(Page 17)
L-CH
R-CH
FL-CH
FR-CH
SL-CH
SR-CH
C-CH
SBL-CH
SBR-CH
A
D
RELAY
DRIVER
Q560
DIGITAL
SECTION
(Page 17)
POWER
SECTION
(Page 20)
J309
RY560
AUDIO
OUT
SUB
WOOFER
• Signal path : TUNER (FM/AM) : VIDEO (AUDIO)
• R-ch is omitted due to same as L-ch.
1616
4-4. BLOCK DIAGRAM — DIGIT AL SECTION —
STR-DE697
DIGITAL
TUNER/
AUDIO
SECTION
(Page 16)
MD/TAPE
OUT
(OPTICAL)
DVD
IN
(COAXIAL)
SA-CD/CD
IN
(OPTICAL)
SA-CD/CD
IN
(OPTICAL)
VIDEO 2
IN
(OPTICAL)
MD/TAPE
IN
(OPTICAL)
TUNER/
AUDIO
SECTION
(Page 16)
-1
-2
A
IC1353
J1301
J1301
IC1354
IC1351
IC1352
B
3
DIN
1
OUT
1
OUT
1
OUT
SYSTEM MUTE
L-IN
R-IN
R-CH
IC1303
WAVE
SHAPER
IC1103
WAVE
SHAPER
SELECTOR
IC1302
3 7 5 6
AB
14 2
Q1103
INV.
Q1104
GATE
AMP
IC1402
3 1
23
23
X1301
12.288MHz
8
D1105
D1106
D1103
DIGITAL AUDIO
I/F RECEIVER
DOUT
2
DIN2
5
DIN1
4
DIN0
3
21
XOUT
22
XIN
+3.3V
Q1105
INV.
SYSTEM_MUTE
24
99
ERROR
25
ANA/DIG
IC1301
VDD
AINL
2
+5V-2
A.5V
INPUT
DEMODULATOR
Pa,Pb DETECTION LOCK
C bit DETECTION
MICROPROCESSOR
CLKCEDI 38 37 36 35 33 47 17
95 96 97 98
DIR CE
DIR_CLK
DATA
I/F
ADC
DIR DI
DO
DIR DO
BPSYNC
NC
CONVERTER
IC1401
LPF
11
20
DETECTION
CKSEL1
94
DIR CKSEL1
A/D
AUDIO
MCLK
XMCK
XMODE
XSTATE
48
93100
DIR_XMODE
DIR_XSTATE
I/F
SDTO
LRCK
SCLK
PDN
13
AUDIO
24
CKOUT
13 22
BCK
14 29
LRCK
15 28
DATAO
16 30
ERROR
34 59
91
SELECT1
90
SELECT2
9
AK5380-PDN
9 18
10 12
D1301
+2.5V
VDDI
+3.3V
VDDE
8
GP12
DIR_DATAO
DSP
IC1501
SDI1 SD01
GP8
69
KFSI0
BCKI2
LRCKI2
SDI2
LRCKI1
15
BCKI1
17
EXLOCK
37
GP12
GP9
HACN
HCS
XRST
HCS1
2 11336 35 33 3432
6 74 18 19 205
HACN1
PM
PM1
XRST1
68
21
GP9
SD02 SD03
SD04
SCKOUT
LRCKO
BCKO
MCLK1
MCLK2
CSO
WEO
BST
HDIN
HDOUT
HDIN
HDOUT
D0-15A0-15
HCLK
HCLK
23 24 25
26
MCLK
14
LRCKO
19
BCKO
20
9
X1502
13.5MHz
12
44 45
98,80 - 77,75 - 72
108,107,105 -102,99,
85-82,66 - 64
112,110,109,97 - 92,
SWITCH
IC1503
56
5
6
92
SYSTEM
CONTROL
IC1101 (2/4)
SWITCH
IC1504
2
1
6
SW
SDRAM
IC1502
CS
6
17
WE
D0-15A0-15
16-13,10 - 7
29 - 32,35 - 38,
1 - 5,18 - 21
24 - 27,42 - 44,
LRCKO
2
1
SW
3
10
BST SEL
GROUPING SW
5
CSN-2
CSN-1
BST
AK4355_CSN
CLK
PDN-2
PDN-1
AK4381_CSN
AK4355_PDN
AK4381_PDN
MCLK LRCKO BCKO CSN-1 PDN-1 CLK CDTI
MCLK LRCKO BCKO CSN-2 PDN-2 CLK CDTI
CDTI
211513121410
AK4355_CLK
AK4355_CDTI
6CH DAC
IC1452
LOUT3-
17
LOUT3+
SDTI3
8
SDTI1
6
SDTI2
7
MCLK
4
LRCK
9
BICK
5
10
CSN
3
PDN CCLK
11
CDTI
12
SDTI
3
MCLK
1
LRCK
4
BICK
2
CSN
6
PDN
5
CLK
7
DTI
8
DAC
DAC
DAC
2CH DAC
IC1451
DAC
ROUT3­ROUT3+
LOUT1­LOUT1+
ROUT1­ROUT1+
LOUT2­LOUT2+
ROUT2­ROUT2+
OUTL­OUTL+
OUTR­OUTR+
18
15 16
25 26
23 24
21 22
19 20
11 12
9
10
• Signal path : VIDEO (AUDIO)
AMP
IC1403
2 3
6 5
AMP
IC1405
2 3
6 5
AMP
IC1404
2 3
6 5
AMP
IC1406
2 3
6 5
1
7
1
7
L OUT
R-CH
SL OUT
R-CH
TUNER/
C
1
7
1
7
C OUT
SW OUT
SBL OUT
R-CH
AUDIO
SECTION
(Page 16)
: CD (ANALOG) : CD (DIGITAL)
• R-ch is omitted due to same as L-ch.
17 17
STR-DE697
4-5. BLOCK DIAGRAM — VIDEO SECTION —
J301 (1/2)
12 13
5 3
2 1
SELECTOR
13
5
3
9 7
V1.IN
13
DVD
3
V2
5
NC
1
V3
9
VIDEO 2
COMPONENT
VIDEO
VIDEO 1
VIDEO 2
VIDEO 3
• Signal path : VIDEO
VIDEO 1
DVD
DVD
DVD
IN
IN
P
B/CB/
P
R/CR/
P
B/CB/
R/CR/
P
VIDEO
VIDEO
VIDEO
VIDEO
-2
S-VIDEO
IN
-1
S-VIDEO
IN
-1
IN
-2
IN
-1
IN
-1
IN
Y
B-Y
R-Y
Y
B-Y
R-Y
J201 (1/2)
J200 (1/2)
J298 (1/2)
J253 (1/2)
Y
C
J252 (1/2)
Y
C
-4
-5
-6
-1
-2
-3
G
G
G
G
COMPONENT VIDEO SELECTOR
0X 1X
0Z 1Z
0Y 1Y
VIDEO
IC203
V1
V2
DVD
V3
NC
IC301
BCA
10 9 11
SW2
10 6 14 2
SW2
SW3
SW2
10 6 14 2
4
SW2
SW3
SW3
4
SW3
XCOM
ZCOM
YCOM
SW4
SW4
SW4
SW4
INH
14
4
15
6
SW1
SW1
Y SWITCH
SW1
SW1
D203,204
IC251
Q301
INV.
OR
3
5
1
SW5
SW5
SW5
VIN2
VIN3
VIN1
6dB AMP
6dB AMP
6dB AMP
6dB AMP
6dB AMP
6dB AMP
6dB AMP
VIDEO AMP
IC302
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
75
75
75
75
75
75
75
VOUT2
VOUT3
VOUT1
V1.OUT
M.OUT
V1.OUT
M.OUT
EXCEPT AEP,UK MODEL
VCC
+5V-3
11
9
13
VEE
-5V-3
SW4
SW3
VCC
+5V-3
15
1
VEE
-5V-3
VCC
+5V-3
15
1
VEE
-5V-3
J301 (2/2)
-7
-8
-9
IC807
J254
+5V
3 1
REG
IC804
-5V
3 2
REG
+5V-3
-5V-3
EXCEPT AEP,UK MODEL
CTRL A1
Y
P
P
B/CB/
R/CR/
B-Y
R-Y
MONITOR
OUT
+15V
-15V
COMPONENT
VIDEO
J200 (2/2)
J201 (2/2)
J253 (2/2)
Y
C
SW1 SW2
SW3 SW4
G
G
-3
VIDEO
OUT
-2
VIDEO
OUT
-1
S-VIDEO
OUT
VIDEO 1
MONITOR
V SW1 V SW2
V SW3 V SW4
CTRL A1
VIDEO 1
KEY/DISPLAY
E
SECTION
(Page 19)
VIDEO 2
-2
S-VIDEO
IN
J252 (2/2)
Y
C
C SWITCH
IC252
V1.OUT
M.OUT
VCC
+5V-3
15
1
VEE
-5V-3
SW5
SW5
6dB AMP
6dB AMP
75
DRIVER
75
DRIVER
G
G
V1
13
DVD
5
V2
3
NC
7
V3
9
SW3
SW4
SW4
SW1
SW1
OR
D251,252
SW2
10 6 14 2
4
SW3
SW2
Y
C
J251
G
S-VIDEO
MONITOR
OUT
G
1818
4-6. BLOCK DIAGRAM — KEY/DISPLAY SECTION —
STR-DE697
VIDEO
SECTION
(Page 18)
V SW1 V SW2 V SW3 V SW4
E
CTRL A1
FLASH
PROGRAMMING
CNP503
1
2 7 6 5
BUFFER
EXCEPT AEP,UK MODEL
EEPROM
IC1131
SDA
SCL
S152
I
/
I
FLASH1
FLASH2 MD2 MD0
RESET
Q1102
5
6
X1101 16MHz
SW1
86
SW2
87
SW3
88
SW4
89
A1 IN
65
A1 OUT
64
83
X1
X0
82
SDA
34
SCL
33
56
POWER KEY
28
FLASH1
27
FLASH2 MD2
51
MD0
49
SYSTEM
CONTROL
IC1101 (3/4)
VOL ENC A VOL ENC B
BLUE LED
FL LAT
FL DATA
FL CLK
SIRCS
ENC A ENC B
FL DISPLAY DRIVER
IC100
SEG1
14
I
SEG16
GRID12
I
GRID1
SW1 SW2 SW3 SW4
REMOTE
CONTROL
RECEIVER
IC102
RV101
-/+
RV102
MASTER VOLUME
I
29
31
I
42
1 2 3 4
SIRCS
STB
9
DIN
7
CLK
8
OUT
1
1
3
1
3
57 59 60
54
29 30
45 46
47
9 4 2
LED DRIVE
Q100
BUFFER
IC101
8 6 3
D101
FL101
VACUUM
FLUORESCENT
DISPLAY
D102-105
+3.3V
(STBY)
IC1111
RESET
A/D0
A/D1
A/D2
38
39
40
12
77
RSTX
SW NETWORK
S131,133,135-141
SW NETWORK
S120-128
SW NETWORK
S100-102,104,106,108,110-112,114
19 19
STR-DE697
4-7. BLOCK DIAGRAM — POWER SECTION —
FL-CH
FR-CH
R-CH
J791
PHONES
PRE DRIVER
IC701
+VOUT2
IN 2
8
PRE
DRIVE
DRIVE
-VOUT2
-B-1 +B
12 11
POWER AMP
Q701-704
R-CH
CURRENT
DETECT
Q705,706
R-CH
OVERLOAD
DETECT
D740,Q740
R-CH
RELAY
DRIVER
Q790
RELAY
DRIVER
Q611
RY791
RY602
R-CH
R-CH
TM602
L
FRONT B
R
TM601
TUNER/
AUDIO
SECTION
(Page 16)
D
SL-CH
SR-CH R-CH
C-CH
SBL-CH
SBR
SYSTEM
CONTROL
IC1101 (4/4)
BRIDGEABLE RY
R-CH
PROTECTOR
HP_RY
FRONT RY
REAR_RY
C/SB RY
HP DETECT
SP_B_RY
P0WER RY
61
62
66
69
68
55
67
72
58
8
1
8
D1107
D1108
IN 2
IN+
IN2
D1111
PRE
DRIVE
PRE
DRIVE
PRE
DRIVE
PRE DRIVER
IC601
DRIVE
PRE DRIVER
IC501
DRIVE
PRE DRIVER
IC700
DRIVE
D721,722,732 Q722,723,725
D1110
HP-RY
FRONTRY
REAR-RY
C/SB RY
HP DETECT
SB-RY
-B-1 +B
-B-1 +B
-B-1 +B
PROTECTOR
+VOUT2
-VOUT2
+VOUT
-VOUT
+VOUT2
-VOUT2
12 11
6 5
12 11
IC691
OVERLOAD
DETECT AMP
-B-1
-B SWITCH Q691,692
72
POWER AMP
Q651-654
POWER AMP
Q501-504
POWER AMP Q1600-1602
R-CH
CURRENT
DETECT
Q655,656
R-CH R-CH
OVERLOAD
DETECT
D640,Q640
RELAY
DRIVER
Q710
RELAY
DRIVER
Q610
RELAY
DRIVER
Q550
RY601
RY501
RY701
R-CH
R-CH
TM501
L
FRONT A
R
L
SURROUND
R
CENTER
SPEAKERS
IMPEDANCE
USE 8-16
• Signal path : TUNER (FM/AM)
• R-ch is omitted due to
CURRENT
DETECT
Q505,506
OVERLOAD
DETECT
D540,Q540
same as L-ch.
• Abbreviation CND: Canadian model
D804
L
R
TRANSFORMER
R810
R811
R910
TRANSFORMER
SURROUND
BACK
T901
POWER
T902
POWER
F901
J911
AC OUTLET
F902
RELAY
RECT D802
DRIVER
Q760
RELAY
DRIVER
Q809
CURRENT
DETECT
Q1603,1604
R-CH
+B
-B
-32V
TU+10V
TU+3.3V
+7V
-7V
+5V-2
+5V-1
+2.5V
+3.3V
+3.3V
(STBY)
IC1904
+3.3V
REG
R-CH R-CH
-32V REG Q801
IC1071
+3.3V
REG
13
13
5 2
OVERLOAD
D1601,Q1605
IC1001
+5V REG
IC1901
BACK-UP
SWITCH
DETECT
AEP,UK MODEL
13
4
HP-RY
IC1902
+10V
REG
IC801
+7V REG
-7V REG
IC802
IC1031
+5V REG
SB-RY
FRONT RY
REAR-RY
13
31
23
13
C/SB RY
HP DETECT
+15V
-15V
RY751
R-CH
RY801(EXCEPT CND) RY802,803(CND)
RECT
D920-923
RECT
D805-808
F1
F2
-32V
RELAY
DRIVER
Q901
RECT
D910-913
RELAY
SWITCH
RY901
STOP
Q921
48
D914
D915
~
AC IN
2020
Loading...
+ 44 hidden pages