3-081-524-E2 (1) GB
Video Cassette
Recorder
Operating Instructions
PAL
SLV-SE830D/E SLV-SE737E SLV-SX737D SLV-SE730D/E SLV-SX730D/E SLV-SE630D/E SLV-SE230D
© 2003 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified service shop.
Precautions
Safety
•This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.
•If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
•Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
•To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Installing
•Do not install this equipment in a confined space such as a book or similar unit.
•Allow adequate air circulation to prevent internal heat buildup.
•Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
•Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
•Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
•Do not place heavy objects on the unit.
•If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL (B/ G) colour system and play back using the PAL (B/ G) colour system. Recording of video sources based on other colour systems cannot be guaranteed.
SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under license from Gemstar Development Corporation.
2 WARNING
Table of contents
Getting Started
4 Index to parts and controls
11Step 1 : Unpacking
12Step 2 : Setting up the remote commander
16 Step 3 : Connecting the VCR
20Step 4 : Setting up the VCR with the Auto Set Up function
23 Setting the clock
25Downloading the TV tuner’s preset data (not available on SLVSE630D/E and SE230D)
26Selecting a language
27Presetting channels
30Changing/disabling programme positions
35Setting the PAY-TV/Canal Plus decoder
Basic Operations
38 Playing a tape
40 Recording TV programmes
44Recording TV programmes using the Dial Timer (SLV-SE830D/E only)
49Recording TV programmes using the ShowView® system (not available on SLV-SE630D/E)
53Recording TV programmes using the timer
Additional Operations
56 Playing/searching at various speeds
58Setting the recording duration time
59Checking/changing/cancelling timer settings
61Recording stereo and bilingual programmes (not available on SLVSE230D)
64Searching using the index function (not available on SLV-SE230D)
66Adjusting the picture
67Reducing the VCR’s power consumption
68Changing menu options
Editing
70Connecting to a VCR or stereo system
72Basic editing
73Audio dubbing (SLV-SE830D/E only)
Additional Information
74 Troubleshooting
78Specifications
79Index
Back Cover
Quick Start Guide
Started Getting
Table of contents 3
Refer to the pages indicated in parentheses ( ) for details.
Front panel
For SLV-SE830D/E
A ?/1 (on/standby) switch
B Remote sensor (12)
C Tape compartment
D A (eject) button (38)
E m (rewind) button (38) (56)
F Shuttle ring (56)
G H (play) button* (38) (56)
H M (fast-forward) button (38) (56)
I JOG button (56)
JREC z (record) button (41) (58) (72)
K x (stop) button* (22) (38) (72) (73)
L X (pause) button (38) (48) (72) (73)
MPROGRAM +/– buttons* (45) (57) (66)
N DIAL TIMER (44)
O AUDIO DUB button (73)
P t LINE-2 L (left) o R (right) jacks (covered)* (70) (71) (73)
How to open the jack cover
1Press the bottom of the cover.
2Hook your finger on the top edge of the cover and pull it open.
*The H (play), x (stop) and PROGRAM + buttons and jack cover have a tactile dot.
4 Index to parts and controls
For SLV-SE737E, SX737D, SE730D/E, SX730D/E and SE630D/E
Started Getting
A ?/1 (on/standby) switch
B Remote sensor (12)
C Tape compartment
D A (eject) button (38)
E m (rewind) button (38) (56)
F H (play) button* (38) (56)
G M (fast-forward) button (38) (56)
HREC z (record) button (41) (58) (72)
I x (stop) button* (22) (38) (72) (73)
J X (pause) button (38) (72) (73)
K PROGRAM +/– buttons* (57) (66)
*The H (play), x (stop) and PROGRAM + buttons have a tactile dot.
continued
Index to parts and controls 5
For SLV-SE230D
A ?/1 (on/standby) switch
B A (eject) button (38)
C Remote sensor (12)
D Tape compartment
E m (rewind) button (38) (56)
F H (play) button* (38) (56)
G M (fast-forward) button (38) (56)
HREC z (record) button (41) (58) (72)
I x (stop) button* (22) (38) (72) (73)
J X (pause) button (38) (72) (73)
K PROGRAM +/– buttons* (57) (66)
*The H (play), x (stop) and PROGRAM + buttons have a tactile dot.
6 Index to parts and controls
Display window
For SLV-SE830D/E, SE737E, SX737D, SE730D/E and SX730D/E
1 |
2 |
3 |
4 |
5 |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Started Getting
8 7
A Tape indicator
B VIDEO indicator (17) (41)
CTime counter/clock/line/programme position indicator (38) (40) (72)
D (smartlink) indicator (18)
For SLV-SE630D/E and SE230D
6
E TV indicator (43)
F STEREO indicator (61)
G Tape speed indicators (40)
HTimer/recording indicator (41) (46) (51) (54)
A Tape indicator
BTime counter/clock/line/programme position indicator (38) (40) (72)
C Timer indicator (46) (51) (54)
D Recording indicator (41)
E STEREO indicator* (61)
F VIDEO indicator (17) (41)
G Playback indicator
* not available on SLV-SE230D
continued
Index to parts and controls 7
Rear panel
For SLV-SE830D/E, SE737E, SX737D, SE730D/E, SX730D/E and
SE630D/E
For SLV-SE230D
A (in from antenna) connector (16) (17)
BLINE-3 (DEC/EXT) connector*1 LINE-2 (DEC/EXT) connector*2 (19) (35) (71)
C Mains lead (16) (17)
DAUDIO (OUT/SORTIE) R/D (right) L/G (left) jacks*3 (19)
ELINE-1 (EURO AV) connector (17) (35) (70)
F (out to tv) connector (16) (17)
*1 SLV-SE830D/E
*2 SLV-SE737E, SX737D, SE730D/E, SX730D/E, SE630D/E and SE230D
*3 not available on SLV-SE630D/E
8 Index to parts and controls
Remote commander
1 2 3
4 5 6
7 8 9
0
A Z (eject) button (38)
B (wide) button (for TV) (14) (15) |
Getting |
|
|
C DISPLAY button (14) (38) (41) |
Started |
E Programme number buttons*1 (13) |
|
D COUNTER/REMAIN button (41) |
|
(42) |
|
F - (ten’s digit) button (13) (42)
G / (Teletext) button (for TV)*2 (14)
H 2 (volume) +/– buttons (for TV) (13)
I a TV power on/TV mode select button (for TV)*2 (13)
J z REC (record) button (41) (58)
KSP (Standard Play)/LP (Long Play) button*3 (40)
L MENU button (23) (59)
M X (pause)/M button (23) (38) x (stop)/m button (23) (38)
m (rewind)/< button (23) (38) (56)
M (fast-forward)/, button (23) (38) (56)
H (play)/OK button*1 (23) (38) (56)
*1 The H (play), AUDIO MONITOR, number 5 and PROG + buttons have a tactile dot.
*2 SLV-SE830D/E, SE737E and SX737D only
*3 not available on SLV-SE230D
continued
Index to parts and controls 9
1 2 3
4 5 6
7 8 9
0
N [TV] / [VIDEO] remote control switch (12)
O ?/1 (on/standby) switch (13) (14) (51)
PAUDIO MONITOR button*1*3 (14) (62)
Q t TV/VIDEO button (13) (17) (41)
R CLEAR button (38) (50) (59)
SINPUT SELECT button (40) (54) (72)
TPROG (programme) +/– buttons*1 (13) (40)
c ⁄ C Teletext page access buttons (for TV)*2 (14)
U y SLOW button*4 (56)
V ×2 button*4 (56)
W ./> (index search) buttons*3*4 (64)
X TIMER button (49) (53)
*1 The H (play), AUDIO MONITOR, number 5 and PROG + buttons have a tactile dot.
*2 SLV-SE830D/E, SE737E and SX737D only
*3 not available on SLV-SE230D
*4 FASTEXT buttons (for TV) (SLVSE830D/E, SE737E and SX737D only)
10 Index to parts and controls
Check that you have received the following items with the VCR:
• Remote commander
•R6 (size AA) batteries
•Aerial cable
Started Getting
Check your model name
The instructions in this manual are for the 11 models: SLV-SE830D, SE830E, SE737E, SX737D, SE730D, SE730E, SX730D, SX730E, SE630D, SE630E and SE230D. Check your model name by looking at the rear panel of your VCR. SLV-SE830D/E is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE830D/E only.”
Unpacking 11
Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
Using the remote commander
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.
Remote sensor
[TV] / [VIDEO]
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
|
0 |
|
To operate |
Set [TV] / [VIDEO] to |
|
|
the VCR |
[VIDEO] and point at the remote sensor at the VCR |
|
|
a Sony TV |
[TV] and point at the remote sensor at the TV |
|
|
12 Setting up the remote commander
|
|
|
?/1 |
DISPLAY |
|
|
AUDIO MONITOR |
|
|
|
t TV/VIDEO |
1 |
2 |
3 |
|
4 |
5 |
6 |
Programme |
7 |
8 |
9 |
number |
buttons |
|||
- |
0 |
|
|
/ |
|
|
|
2 +/– |
|
|
PROG +/–/ |
a |
|
|
c ⁄ C |
FASTEXT buttons
TV control buttons
To |
|
Press |
|
|
|
|
|
Set the TV to standby mode |
|
?/1 |
|
|
|
|
|
Select an input source: aerial in or line in |
|
t TV/VIDEO |
|
|
|
|
|
Select the TV’s programme position |
|
Programme number buttons, |
|
|
|
-, PROG +/– |
|
|
|
|
|
Adjust the volume of the TV |
|
2 +/– |
|
|
|
|
|
Switch to TV (Teletext off)*1 |
|
a (TV) |
|
|
|
|
|
|
|
continued |
|
|
Setting up the remote commander |
Started Getting
13
To |
Press |
|
|
Switch to Teletext*1 |
/ (Teletext) |
|
|
Select the sound*2 |
AUDIO MONITOR |
|
|
Use FASTEXT*1 |
FASTEXT buttons |
|
|
Call up the on-screen display |
DISPLAY |
|
|
Change the Teletext page*1 |
c ⁄ C |
|
|
Switch to/from wide mode of a Sony wide TV (For |
(wide) |
other manufactures’ wide TVs, see “Controlling |
|
other TVs with the remote commander (SLV- |
|
SE830D/E, SE737E and SX737D only)” below.) |
|
|
|
Notes
•With normal use, the batteries should last about three to six months.
•If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
•Do not use a new battery together with an old one.
•Do not use different types of batteries together.
•Some buttons may not work with certain Sony TVs.
*1 SLV-SE830D/E, SE737E and SX737D only *2 not available on SLV-SE230D
Controlling other TVs with the remote commander (SLVSE830D/E, SE737E and SX737D only)
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number.
1 Set [TV] / [VIDEO] at the top of the remote commander to [TV].
2 Hold down ?/1, and enter your TV’s code number using the programme number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit), PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,
(wide)*, MENU*, M/m/</,*, and OK*.
* These buttons may not work with all TVs.
14 Setting up the remote commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable code numbers.
Manufacturer |
Code number |
|
|
Sony |
01*1, 02 |
|
|
Akai |
68 |
|
|
Ferguson |
52 |
|
|
Grundig |
10*1, 11*1 |
|
|
Hitachi |
24 |
|
|
JVC |
33 |
|
|
Loewe |
45 |
|
|
Mivar |
09, 70 |
|
|
NEC |
66 |
|
|
Nokia |
15, 16, 69*3 |
|
|
Manufacturer |
Code number |
|
|
Panasonic |
17*1, 49 |
|
|
Philips |
06*1, 07*1, 08*1 |
|
|
Saba |
12, 13 |
|
|
Samsung |
22, 23 |
|
|
Sanyo |
25 |
|
|
Sharp |
29 |
|
|
Telefunken |
36 |
|
|
Thomson |
43*2 |
|
|
Toshiba |
38 |
|
|
*1 Press (wide) to switch the wide picture mode on or off.
*2 Press (wide), then press 2 +/– to select the wide picture mode you want.
*3 Press (wide). The menu appears on the TV screen. Then, press M/m/</, to select the wide picture you want and press OK.
Tip
•When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.
Notes
•If you enter a new code number, the code number previously entered will be erased.
•If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.
•When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.
Started Getting
Setting up the remote commander 15
If your TV has a Scart (EURO-AV) connector, see page 17.
If your TV does not have a Scart (EURO-AV) connector
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
1
2
3
Disconnect the aerial cable from your TV and connect it to on the rear panel of the VCR.
Connect of the VCR and the aerial input of your TV using the supplied aerial cable.
Connect the mains lead to the mains.
Note
•When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 20).
16 Connecting the VCR
If your TV has a Scart (EURO-AV) connector
|
LINE-1 (EURO AV) |
Mains lead |
|
|
|
|
AERIAL IN |
to mains |
|
|
|
Scart |
Aerial cable (supplied) |
|
|
|
|
(EURO-AV) |
|
|
: Signal flow |
Scart cable (not supplied) |
|
|
|
Started Getting
1
2
3
4
Disconnect the aerial cable from your TV and connect it to on the rear panel of the VCR.
Connect of the VCR and the aerial input of your TV using the supplied aerial cable.
Connect LINE-1 (EURO AV) on the VCR and the Scart (EUROAV) connector on the TV with the optional Scart cable.
This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press t TV/VIDEO to display the VIDEO indicator in the display window.
Connect the mains lead to the mains.
continued
Connecting the VCR 17
About the SMARTLINK features (not available on SLV-SE630D/E and SE230D)
If the connected TV complies with
SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link*3, EURO VIEW LINK*4, or T-V LINK*5, this
VCR automatically runs the
SMARTLINK function after you complete the steps on the previous page (the indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
•TV Direct Rec
You can easily record what you are watching on the TV when the VCR is turned on. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE630D/E and SE230D)” on page 43.
•One Touch Play
With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE630D/E and SE230D)” on page 39.
•One Touch Menu
When the VCR is turned on, you can turn on the TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.
•One Touch Timer
When the VCR is turned on, you can turn on the TV, set the TV to the video channel, and display the timer recording menu (the TIMER PROGRAMMING menu or the SHOWVIEW menu) automatically by
pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER METHOD in the EASY OPERATION menu (see page 69).
•NexTView Download
You can easily set the timer by using the NexTView Download function on your TV. Please refer to your TV’s instruction manual.
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation. *2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation. *5 “T-V LINK” is a trademark of JVC Corporation.
Note
• Not all TVs respond to the functions above.
18 Connecting the VCR
Additional connections
To a stereo system (not available on SLVSE630D/E and SE230D)
You can improve sound |
AUDIO R/D L/G |
LINE IN |
|
quality by connecting a |
|
stereo system to the AUDIO |
|
R/D L/G jacks as shown on |
|
the right. |
Audio cable (not supplied) |
|
: Signal flow |
To a satellite or digital tuner with Line Through
Using the Line Through function, you can watch programmes from a satellite or digital tuner connected to this VCR on the TV even when the VCR is turned off. When you turn on the satellite or digital tuner, this VCR automatically sends the signal from the satellite or digital tuner to the TV without turning itself on.
LINE-3 |
(DEC/EXT)*1 or |
LINE |
LINE-2 |
(DEC/EXT)*2 |
|
|
|
OUT |
Scart cable (not supplied)
: Signal flow
1 Connect the satellite or digital tuner to the LINE-3 (DEC/EXT)*1 or LINE-2 (DEC/EXT)*2 connector as shown above.
2 Turn off the VCR.
To watch a programme, turn on the satellite or digital tuner and the TV.
Notes
•The Line Through function will not operate properly if POWER SAVE in the USER SET menu is set to ECO2. Set POWER SAVE to OFF or ECO1 to ensure proper operation (see page 67).
•You cannot watch programmes on the TV while recording unless you are recording a satellite or digital programme.
•This function may not work with some types of satellite or digital tuners.
•When the VCR is turned off, set the TV to the video channel.
*1 SLV-SE830D/E
*2 SLV-SE737E, SX737D, SE730D/E, SX730D/E, SE630D/E and SE230D
Started Getting
Connecting the VCR 19
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display, TV channels, guide channels for the ShowView system*, and VCR clock* automatically.
1
2
Turn on your TV and set it to the video channel.
If your TV does not have a Scart (EURO-AV) connector, tune the TV to channel 32 (the initial RF channel for this VCR). Refer to your TV manual for TV tuning instructions. If the picture does not appear clearly, see “To change the RF channel” on page 22.
Connect the mains lead to the mains.
The VCR automatically turns on, and the language abbreviations appear on the TV screen.
The abbreviations of the languages are as follows:
Abbreviation |
Language |
|
|
GB |
English |
|
|
ES |
Spanish |
|
|
NL |
Dutch |
|
|
FI |
Finnish |
|
|
DE |
German |
|
|
IT |
Italian |
|
|
|
|
|
|
|
|
|
|
GB |
|
DE |
FR |
|
|
ES |
IT |
PT |
|
|
|
NL |
SE |
DK |
|
|
|
FI |
GR |
TR |
|
SELECT : |
|
|
|||
SET |
: OK |
|
EXIT : MENU |
Abbreviation |
Language |
|
|
SE |
Swedish |
|
|
GR |
Greek |
|
|
FR |
French |
|
|
PT |
Portuguese |
|
|
DK |
Danish |
|
|
TR |
Turkish |
|
|
3
OK
Press M/m/</, to select the language abbreviation from the table in step 2, then press OK.
The message for the Auto Set Up function appears.
20 Setting up the VCR with the Auto Set Up function
4
OK
Press OK.
The COUNTRY SELECTION menu* appears.
The abbreviations of the countries are as follows:
COUNTRY SELECTION
A |
I |
TR |
B |
N |
GR |
DK |
P |
HU |
FIN |
E |
PL |
D |
S |
CZ |
NL |
CH |
OTHERS |
SELECT : |
|
|
SET |
: OK |
EXIT : MENU |
Started Getting
|
Abbreviation |
Country |
|
Abbreviation |
Country |
|
|
|
|
|
|
|
A |
Austria |
|
E |
Spain |
|
|
|
|
|
|
|
B |
Belgium |
|
S |
Sweden |
|
|
|
|
|
|
|
DK |
Denmark |
|
CH |
Switzerland |
|
|
|
|
|
|
|
FIN |
Finland |
|
TR |
Turkey |
|
|
|
|
|
|
|
D |
Germany |
|
GR |
Greece |
|
|
|
|
|
|
|
NL |
Netherlands |
|
HU |
Hungary |
|
|
|
|
|
|
|
I |
Italy |
|
PL |
Poland |
|
|
|
|
|
|
|
N |
Norway |
|
CZ |
Czech |
|
|
|
|
|
|
|
P |
Portugal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
For SLV-SE830D/E, SE737E, |
|
|
|
|
|
SX737D, SE730D/E, SX730D/E |
|
OK |
and SE230D |
AUTO SET UP |
|
Press M/m/</, to select the |
PLEASE WAIT |
|
abbreviation of your country from |
4 0 % |
|
the table in step 4, then press OK. |
|
|
If your country does not appear, |
EXIT : MENU |
|
select OTHERS. |
|
The VCR starts searching for all of the receivable channels and presets them (in the appropriate order for your local area).
If you want to change the order of the channels or disable unwanted programme positions, see “Changing/disabling programme positions” on page 30.
After the search or download is complete, the current time appears for any stations that transmit a time signal. If the time does not appear, set the clock manually. See “Setting the clock” on page 23.
For SLV-SE630D/E
The clock setting menu appears. See “Setting the clock” on page 23.
continued
Setting up the VCR with the Auto Set Up function 21
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the VCR and TV. Select INSTALLATION from the menu, then press M/m to highlight VCR OUTPUT CH and press ,. Select the RF channel by pressing the M/m buttons. Then, tune the TV to the new RF channel so that a clear picture appears.
Tip
•If you want to change the language for the on-screen display from the one preset in the Auto Set Up function, see page 26.
Notes
•Whenever you operate the Auto Set Up function, some of the settings (ShowView*, timer, etc.) will be reset. If this happens, you have to set them again.
•Auto preset starts automatically only when you plug in the mains lead for the first time after you purchase the VCR.
•After using the Auto Set Up function, the language abbreviations do not appear automatically when you connect the mains lead again. If you want to use the Auto Set Up function again, press MENU, then press M/m/</, to highlight INSTALLATION and press OK. Press M/m to highlight AUTO SET UP, then repeat all procedures from step 4.
•Auto preset can be performed by pressing x (stop) on the VCR continuously for 5 seconds or more with no tape inserted.
* not available on SLV-SE630D/E
22 Setting up the VCR with the Auto Set Up function
You must set the time and date on the VCR to use the timer features properly.
The Auto Clock Set function* works only if a station in your area is broadcasting a time signal.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “Index to parts and controls” for button locations.
1 |
MENU |
Press MENU, then press M/m/</ |
|
|
|
|
, to highlight CLOCK SET and |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
press OK. |
|
|
|
|
|
|
1 2 : 0 0 |
1 / JAN / 2 0 0 3 |
|||
|
|
|
|
|
WED |
|
|
|
AUTO CLOCK |
: ON |
|
||
|
OK |
|
|
|
|
|
|
|
SELECT : |
|
SET |
: |
|
|
|
END |
: OK |
|
EXIT |
: MENU |
2 |
|
Press M/m to set the hour. |
|
|
|
|
|
|
|
|
|
|
|
|
OK |
|
|
|
|
|
|
|
1 8 : 0 0 |
1 / JAN / 2 0 0 3 |
|||
|
|
|
|
|
WED |
|
|
|
AUTO CLOCK |
: ON |
|
||
|
|
SELECT |
: |
|
SET |
: |
|
|
END |
: OK |
|
EXIT |
: MENU |
Started Getting
3 |
Press , to select the minutes and |
|
|
|
set the minutes by pressing M/m. |
|
OK |
1 |
8 : 3 0 |
1 / JAN / 2 0 0 |
3 |
||
|
|
|
|
WED |
|
|
AUTO CLOCK |
: ON |
|
||
SELECT : |
|
SET |
: |
|
|
END |
: OK |
|
EXIT |
: MENU |
4
OK
Set the day, month, and year in sequence by pressing , to select the item to be set, and press M/m to select the digits, then press ,.
The day of the week is set automatically.
1 8 : 3 0 2 8 / SEP / 2 0 0 3 SUN
AUTO CLOCK : ON
SELECT |
: |
SET |
: |
END |
: OK |
EXIT |
: MENU |
continued
Setting the clock 23
5
6
|
Press M/m to select ON for the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
setting of the Auto Clock Set |
|
|
|
|
|
|
OK |
function*. |
|
|
|
|
|
|
|
|
|
1 8 : 3 0 2 8 / SEP / 2 0 0 3 |
||||
|
The VCR automatically sets the |
|
|
|
|
SUN |
|
|
|
|
|
|
|
|
|
|
clock according to the time signal |
|
|
AUTO CLOCK |
: ON |
|
|
|
broadcast between the channels |
|
SELECT : |
SET |
: |
|
|
|
PR 1 to PR 5. |
|
|
||||
|
|
END |
: OK |
EXIT |
: MENU |
If you do not need the Auto Clock
Set function, select OFF.
Press MENU to exit the menu.
MENU
Tips
•If you set AUTO CLOCK* to ON, the Auto Clock Set function is activated whenever the VCR is turned off. The time is adjusted automatically by making reference to the time signal from the station.
•To change the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m.
* not available on SLV-SE630D/E
24 Setting the clock