3-865-319-12 (2)
Video Cassette
Recorder
Operating Instructions
PAL NTSC 4.43
SLV-SE80UX
©1999 by Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified service shop.
Notice for customers in the United Kingdom
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
If the 13A fitted plug does not match the outlet socket in your home, please refer to your Appointed Sony Dealer for advice.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS1362, (i.e., marked with 2 or @ mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Precautions
Safety
•This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.
•If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
•Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
Installing
•Allow adequate air circulation to prevent internal heat buildup.
•Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
•Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
•Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
•Do not place heavy objects on the unit.
•If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL
(I) colour system and play back using the PAL
(I) and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
2 Introduction
Table of contents
Getting Started
4 Step 1: Unpacking
5 Step 2: Setting up the remote commander
9 Step 3: Connecting the VCR
14Step 4: Setting up the VCR with the Auto Set Up function
15Step 5: Tuning your TV to the VCR
17 Selecting a language
19 Presetting channels
22 Changing/disabling programme positions
28 Setting the clock
32 Setting your personal code
Basic Operations
34 Playing a tape
37 Recording TV programmes
41Recording TV programmes using the VIDEO Plus+* system
45 Setting the timer manually
Additional Operations
48Playing/searching at various speeds
51Recording TV programmes using Dial Timer
54Setting the recording duration time
55Checking/changing/cancelling timer settings
57Recording stereo and bilingual programmes
59Searching using the Smart Search function
62Searching using the index function
63Adjusting the picture
65 Changing menu options
Editing
68Connecting to a VCR or stereo system
69Basic editing
70Audio dubbing
Additional Information
72 Troubleshooting
75Specifications
76Index to parts and controls
Back cover
Index
*VIDEO Plus+ and PlusCode are trademarks applied for by Gemstar Development Corp. VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.
Started Getting
Introduction 3
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander • Aerial cable
• EURO-AV cable
• R6 (size AA) batteries
4 Getting Started
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote |
Remote sensor |
commander to operate this |
|
VCR and a Sony TV. Buttons |
|
on the remote commander |
|
marked with a dot (•) can be |
|
used to operate your Sony TV. |
|
If the TV does not have the g |
|
symbol near the remote sensor, |
|
this remote commander will |
|
not operate the TV. |
|
TV / VIDEO
|
1 |
2 |
3 |
|||||
|
4 |
5 |
6 |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To operate |
Set |
TV |
/ |
VIDEO |
to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
the VCR |
VIDEO |
and point at the remote sensor on the VCR |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
a Sony TV |
TV |
and point at the remote sensor on the TV |
||||||
|
|
|
|
|
|
|
|
|
continued
Started Getting
Getting Started 5
Step 2 : Setting up the remote commander (continued)
|
|
|
I/u |
WIDE |
|
|
V |
AUDIO MONITOR |
|
|
; |
FASTEXT buttons |
|
|
|
DISPLAY |
|
|
…TV/VIDEO |
1 |
2 |
3 |
|
4 |
5 |
6 |
Programme |
|
|
|
number |
7 |
8 |
9 |
buttons |
? |
0 |
|
|
PROG+/–/
√/◊
Á +/–
TV control buttons
To |
Press |
Turn the TV into standby mode |
I/u |
|
|
Select an input source of the TV either from |
…TV/VIDEO |
aerial in or from line in |
|
|
|
Select the programme position of the TV |
Programme number buttons, |
|
?, PROG +/– |
|
|
Adjust the volume of the TV |
Á+/– |
|
|
6 Getting Started
To |
Press |
|
|
Switch to TV (Teletext off) |
;(TV) |
|
|
Switch to Teletext |
V(Teletext) |
|
|
Select the sound |
AUDIO MONITOR |
|
|
Use FASTEXT |
FASTEXT buttons |
|
|
Call up on-screen display |
DISPLAY |
|
|
Change the Teletext page |
√/◊ |
|
|
Switch to/from wide mode of a Sony wide TV (For |
WIDE |
other manufacture’s wide TV, see “Controlling other |
|
TVs with the remote commander” below.) |
|
|
|
Notes
•With normal use, the batteries should last about three to six months.
•If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
•Do not use a new battery with an old one together.
•Do not use different types of batteries together.
•Some buttons may not work with certain Sony TVs.
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the table below, set the appropriate manufacturer’s code number.
1Set TV / VIDEO at the top of the remote commander to TV .
2Hold down I/u, and enter your TV’s code number(s) using the programme number buttons. Then release I/u.
Now you can use the following TV control buttons to control your TV: I/u, TV/VIDEO, programme number buttons, ?(ten’s digit), PROG +/–, Á+/–, ;(TV), V(Teletext), FASTEXT buttons, WIDE*, MENU*, >*/.*/?*//*, and OK*.
* These buttons may not work with all TVs.
Tip
•When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.
continued
Started Getting
Getting Started 7
Step 2 : Setting up the remote commander (continued)
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
To make wide mode settings, see the footnotes below this table for the applicable code numbers.
Manufacturer |
Code number |
|
|
Sony |
01*1, 02 |
Akai |
68 |
Ferguson |
52 |
Grundig |
10*1, 11*1 |
Hitachi |
24 |
JVC |
33 |
Loewe |
45 |
Mivar |
09, 70 |
NEC |
66 |
Nokia |
15, 16, 69*3 |
Manufacturer |
Code number |
|
|
Panasonic |
17*1, 49 |
Philips |
06*1, 07*1, 08*1 |
Saba |
12, 13 |
Samsung |
22, 23 |
Sanyo |
25 |
Sharp |
29 |
Telefunken |
36 |
Thomson |
43*2 |
Toshiba |
38 |
*1 Press WIDE to switch the wide picture mode on or off.
*2 Press WIDE, then press Á+/– to select the wide picture mode you want.
*3 Press WIDE. The menu appears on the TV screen. Then, press >/./?// to select the wide picture you want and press OK.
Notes
•If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.
•If you enter a new code number, the code number previously entered will be erased.
•When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.
8 Getting Started
Step 3
Connecting the VCR
If your TV does not have a EURO-AV connector, see page 12.
If your TV has a EURO-AV (Scart) connector
Mains lead
to mains
: Signal flow
|
AERIAL IN |
|
:LINE-1 |
AERIAL OUT |
|
(TV) |
||
|
AERIAL IN
Aerial cable (supplied)
EURO-AV (Scart)
EURO-AV cable (supplied)
Started Getting
1
2
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on the |
AERIAL |
|
ANTENNE |
||
rear panel of the VCR. |
IN |
|
ENTREE |
||
|
||
|
OUT |
|
|
SORTIE |
|
Connect AERIAL OUT of the VCR and |
AERIAL |
|
ANTENNE |
||
the aerial input of your TV using the |
IN |
|
ENTREE |
||
|
||
supplied aerial cable. |
OUT |
|
|
SORTIE |
continued
Getting Started 9
Step 3 : Connecting the VCR (continued)
3
4
Connect LINE-1 (TV) on the VCR and the EURO-AV (Scart) connector on the TV with the supplied EURO-AV cable.
This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press
…TV/VIDEO to display the VIDEO indicator in the display window.
Connect the mains lead to the mains.
If the mains plug does not fit in the mains, use the supplied plug adapter.
Note
•If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 67). You do not have to tune your TV to the VCR. Skip “Tuning your TV to the VCR” on page 15.
About the SMARTLINK features
If the connected TV complies with |
SMARTLINK |
SMARTLINK, MEGALOGIC*1, EASYLINK*2, |
|
Q-Link*3 or EURO VIEW LINK*4, you can use |
|
the SMARTLINK function after you complete |
|
|
the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
•Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful, not to disconnect the cables or exit the Auto Set Up function during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 14.
10 Getting Started
• TV Direct Rec
You can easily record what you are watching on the TV (other than tapes being played on this VCR). For details, see “Recording what you are watching on the TV (TV Direct Rec)” on page 40.
• One Touch Play |
|
|
With One Touch Play, you can start playback automatically without turning on the |
|
|
TV. For details, see “Starting playback automatically with one button (One Touch |
|
|
Play)” on page 36. |
Getting |
|
• One Touch Menu |
||
|
||
You can turn on the VCR and TV, set the TV to the video channel, and display the |
|
|
VCR’s on-screen display automatically by pressing MENU on the remote |
Started |
|
commander. |
||
|
• One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the TIMER menu, or the VIDEO PLUS+ menu) automatically by pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 67).
•Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation. *2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation.
Note
• Not all the TVs respond to the functions above.
continued
Getting Started 11
Step 3 : Connecting the VCR (continued)
If your TV does not have a EURO-AV (Scart) connector
AERIAL IN
AERIAL OUT
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
1
2
3
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on the |
AERIAL |
|
ANTENNE |
||
rear panel of the VCR. |
IN |
|
ENTREE |
||
|
OUT |
|
|
SORTIE |
|
Connect AERIAL OUT of the VCR and |
AERIAL |
|
ANTENNE |
||
|
||
the aerial input of your TV using the |
IN |
|
ENTREE |
||
supplied aerial cable. |
OUT |
|
|
SORTIE |
Connect the mains lead to the mains.
If the mains plug does not fit in the mains, use the supplied plug adapter.
Note
•When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in the OPTIONS-2 menu to ON (initial setting) (see page 67).
12 Getting Started
Additional connections
To a stereo system
You can improve sound quality by connecting a stereo system to the AUDIO OUT R/L jacks as shown on the right.
AUDIO OUT |
LINE IN |
R/L |
Audio cable (not supplied)
: Signal flow
To a satellite tuner
You can watch programmes from the satellite tuner connected to this VCR on the TV even when the VCR is turned off using the Line Through function. When you turn on the satellite tuner, this VCR automatically sends the signal from the satellite tuner to the TV without turning itself on.
…LINE-3 IN
LINE OUT
EURO-AV cable (not supplied) : Signal flow
1Connect the satellite tuner to the LINE-3 IN connector as shown above.
2Set POWER SAVE to OFF in the OPTIONS-2 menu.
3Turn off the VCR.
To watch a satellite programme, turn on the satellite tuner and the TV.
Note
•You cannot watch satellite programmes on the TV while recording unless you record a satellite programme.
Started Getting
Getting Started 13
Step 4
Setting up the VCR with the Auto Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set TV channels, guide channels for the VIDEO Plus+ system, the RF channel, and VCR clock automatically.
AUTO SET UP
AUTO SET UP
Hold down AUTO SET UP on the VCR for more than three seconds.
The VCR automatically turns on and starts searching for all of the receivable channels and presets them in the appropriate order for your local area.
If you use the SMARTLINK connection, the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download.
After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal. If the time does not appear, set the clock manually. See page 28.
To cancel the Auto Set Up function
Press AUTO SET UP.
Note
• Do not cancel the Auto Set Up function. If you do, repeat the step above.
14 Getting Started
Step 5
Tuning your TV to the VCR
If you have connected the VCR to your TV using the EURO-AV cable, skip this step.
RF CHANNEL
1 |
Press RF CHANNEL on the VCR lightly. |
|
The factory-preset RF channel appears in the display window. |
|
RF CHANNEL |
The VCR signal is output through this channel to the TV.
Started Getting
2
3
Turn on your TV and select a programme position for the VCR picture.
This programme position will now be referred to as the video channel.
Tune the TV to the same channel as that
shown in the display window so that SONY VIDEO CASSETTE RECORDER the picture on the right appears clearly
on the TV screen.
Refer to your TV manual for tuning instructions.
If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.
continued
Getting Started 15
Step 6 : Setting the clock (continued)
4 |
Press RF CHANNEL. |
|
You have now tuned your TV to the VCR. Whenever you want to |
RF CHANNEL
play a tape, set the TV to the video channel.
To check to see if the TV tuning is correct
Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR
If the screen does not appear clearly in step 3 above, press PROGRAM +/–, so that another RF channel appears. Then tune the TV to the new RF channel until a clear picture appears.
16 Getting Started
Selecting a language
MENU
If you prefer an on-screen language other than English, use the on-screen display to select another language.
Before you start… |
>/. |
• Turn on the VCR and the TV. |
OK |
|
• Set the TV to the video channel.
1 |
MENU |
Press MENU, then press >/. to |
SETTINGS |
|
|
|
|
||
|
|
highlight SETTINGS and press OK. |
TUNER |
|
|
|
|
CLOCK |
|
|
|
|
LANGUAGE |
|
|
|
|
RETURN |
|
|
PLAY |
|
|
|
|
OK |
|
SELECT |
: |
|
|
|
SET |
: OK |
|
|
|
|
EXIT : MENU |
2 |
|
Press >/. to highlight LANGUAGE, |
LANGUAGE |
|
|
PLAY |
then press OK. |
|
ENGLISH |
|
|
|
|
DEUTSCH |
|
OK |
|
|
FRANÇAIS |
|
|
|
ITALIANO |
|
|
|
|
|
|
|
|
|
|
ESPAÑOL |
|
|
|
|
PORTUGUÊS |
|
|
|
|
NEDERLANDS |
|
|
|
|
EΛΛHNIKA |
|
|
|
SELECT |
: |
|
|
|
SET |
: OK |
|
|
|
|
EXIT : MENU |
3 Press >/. to highlight the desired language, then press OK.
PLAY
OK
continued
Started Getting
Getting Started 17
Selecting a language (continued)
4MENU
Press MENU to exit the menu.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
•The menu disappears automatically if you don’t proceed for more than a few minutes.
18 Getting Started
Presetting channels
If some channels could not be preset using the Auto Set Up function, you can preset them manually.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
PROG +/–
MENU
>/./?//
OK
1 |
MENU |
Press MENU, then press >/. to |
SETTINGS |
|
|
|
|
|
|
highlight SETTINGS and press OK. |
TUNER |
|
|
|
|
|
|
|
CLOCK |
|
|
|
|
|
|
|
LANGUAGE |
|
|
|
|
|
|
|
RETURN |
|
|
|
|
|
PLAY |
|
|
|
|
|
|
|
OK |
|
SELECT |
: |
|
|
|
|
|
|
SET |
: OK |
EXIT : MENU |
||
|
|
|
|
|
|||
2 |
|
Press >/. to highlight TUNER, then |
TUNER |
|
PROG. |
1 |
|
|
|
|
|
|
|
||
|
PLAY |
press OK. |
CHANNEL SET |
C1 2 |
AAB |
|
|
|
|
|
AFT |
|
ON |
|
|
|
OK |
|
FINE TUNING |
|
|
|
|
|
|
RETURN |
|
|
|
||
|
|
|
|
|
|
SELECT :
SET : OK
EXIT : MENU
continued
Started Getting
Getting Started 19
Presetting channels (continued)
3• PROG
Press PROG +/– to select the programme |
Selected programme |
|||||||
position. |
position |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TUNER |
PROG. 4 |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
||
|
|
|
CHANNEL SET |
C1 2 AAB |
|
|
|
|
|
|
|
AFT |
|
ON |
|
|
|
|
|
|
FINE TUNING |
|
|
|
|
|
|
|
|
RETURN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SELECT |
: |
SET |
: OK |
|
|
|
EXIT : MENU |
4 |
Press >/. to highlight CHANNEL SET, |
TUNER |
PROG. 4 |
PLAY |
then press OK. |
CHANNEL SET |
C1 2 AAB |
|
|
AFT |
|
OK |
|
FINE TUNING |
|
|
RETURN |
|
|
|
|
|
|
|
|
SELECT : |
|
|
|
CONFIRM : OK |
EXIT : MENU |
|
|
|
5 |
Press >/. repeatedly until the channel you want is displayed. |
PLAY
OK
The channels appear in the following order:
• UHF B21 - B69
If you know the number of the channel you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”
TUNER |
PROG. |
4 |
||
|
|
|||
CHANNEL SET |
C2 7 |
|
|
|
AFT |
|
|
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
SELECT |
: |
|
|
|
CONFIRM |
: OK |
EXIT |
: MENU |
|
|
|
6 |
|
To allocate another channel to another programme position, repeat |
|
|
steps 3 and 5. |
|
|
|
7 |
MENU |
Press MENU to exit the menu. |
|
|
|
20 Getting Started
Disabling unwanted programme positions
After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons.
1In step 5 above, press programme number button “0” twice to display the number “00” beside CHANNEL SET.
2Press MENU to exit the menu.
If the picture is not clear
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture is not clear, you may also use the manual tuning function.
1Press PROG +/– or the programme number buttons to select the programme position for which you cannot obtain a clear picture.
2Press MENU, then select SETTINGS and press OK.
3Select TUNER, then press OK.
4Select FINE TUNING, then press OK. The fine tuning meter appears.
|
|
TUNER |
|
|
PROG. 4 |
|
Selected programme |
||
|
|
|
|
|
|
position |
|||
|
AFT |
|
|
|
|
|
|
||
|
CHANNEL SET |
C2 7 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
FINE TUNING |
|
|
|
|
|
|
|
|
|
RETURN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SET :
EXIT : MENU
5Press ?// to get a clearer picture, then press MENU to exit the menu.
Note that the AFT (Auto Fine Tuning) setting switches to OFF.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
•The menu disappears automatically if you don’t proceed for more than a few minutes.
Started Getting
Getting Started 21
Changing/ disabling programme positions
After setting the channels, you can change the programme positions and the station names as you like. If any programme positions are unused or contain unwanted channels, you can disable them.
MENU
>/.//
OK
Changing programme positions
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
1MENU
PLAY
OK
Press MENU, then press >/. to highlight LISTS and press OK.
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
2
PLAY
OK
Press >/. to highlight CHANNEL LIST, then press OK.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
|
|
|
C0 9 |
FGH |
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
|
|
||
MOVE PROG |
: |
|
|
|
|
ERASE PROG |
: |
CLEAR |
|
EXIT : MENU
3
PLAY
OK
Press >/. to highlight the row on which you want to change the programme position, then press /.
To display other pages for programme positions 6 to 60, press >/. repeatedly.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
C0 9 |
|
|
|
FGH |
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|
|
|
|
||
SET STATION NAME |
|
: |
|
|
|
|
CONFIRM |
|
: |
OK |
|
EXIT : MENU
22 Getting Started
4
PLAY
OK
Press >/. until the selected channel row moves to the desired programme position.
The selected channel is inserted at the new programme position and the intermediate channels are displaced to fill the gap.
|
CHANNEL LIST |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
PROG |
CH |
|
|
|
NAME |
|
||
|
1 |
|
C0 3 |
|
|
|
CDE |
|
||
2 |
|
C5 6 |
|
|
|
|
|
|
||
|
|
3 |
|
C1 2 |
|
|
|
AAB |
|
|
|
|
4 |
|
C2 7 |
|
|
|
|
|
|
5 |
|
C0 9 |
|
|
|
FGH |
||||
|
|
|
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|||
|
|
|
|
|
|
|||||
SET STATION NAME |
|
: |
|
|
|
|
|
|||
CONFIRM |
|
: |
OK |
|
EXIT : MENU
5 |
|
Press OK to confirm the setting. |
|
PLAY |
|
|
OK |
|
6 |
|
To change the programme position of another station, repeat steps 3 |
|
|
to 5. |
7 |
MENU |
Press MENU to exit the menu. |
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
•The menu disappears automatically if you don’t proceed for more than a few minutes.
continued
Started Getting
Getting Started 23
Changing/disabling programme positions (continued)
Changing the station names
You can change the station names (up to 5 characters).
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
MENU
>/./?//
OK
1MENU
PLAY
OK
Press MENU, then press >/. to highlight LISTS and press OK.
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
2
PLAY
OK
Press >/. to highlight CHANNEL LIST, then press OK.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
|
|
|
C0 9 |
FGH |
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
|
|
||
MOVE PROG |
: |
|
|
|
|
ERASE PROG |
: |
CLEAR |
|
EXIT : MENU
3
PLAY
OK
Press >/. to highlight the row on which you want to change the station name, then press /.
To display other pages for programme positions 6 to 60, press >/. repeatedly.
CHANNEL LIST
PROG |
CH |
NAME |
|
1 |
C1 2 |
AAB |
|
2 |
C0 3 |
CDE |
|
3C5 6
4C2 7
5 |
C0 9 |
|
|
|
FGH |
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|
|
|
|
||
SET STATION NAME |
|
: |
|
|
|
|
CONFIRM |
|
: |
OK |
|
EXIT : MENU
24 Getting Started