Sony SDX-800V, SDX-1100V User Manual

AIT Drive

2-891-321-12(1)

User’s Guide

AIT-5 TAPE DRIVE

SDX-1100V Series

AIT-4 TAPE DRIVE

SDX-900V Series

AIT-3 Ex TAPE DRIVE

SDX-800V Series

2006 Sony Corporation

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This document contains proprietary information which is protected by copyright.

The information contained in this document is subject to change without notice.

SONY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS DOCUMENT.

Sony shall not be liable for errors contained herein, indirect, special, incidental or consequential damages in connection with the furnishing, performance or use of this document.

Your SDX-1100V is assigned a Model No. SDX-1100 for regulatory compliance certifications. Your SDX-900V and SDX-800V are assigned a Model No. ATDNA4 for regulatory compliance certifications. The number is indicated on the model number label on your drive along with the rated voltage and current.

Hinweis

MaschinenlärminformationsVerordnung - 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779.

ATTENTION

According to the EU Directives related to product safety, EMC and R&TTE the manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorised Representative is Sony Deutschland GmbH, Hedelfinger Strasse 61,70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

AUFMERKSAMKEIT

Im Sinne der EU Richtlinien bezüglich Produktsicherheit, EMV und R&TTE ist Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan der Hersteller dieses Produktes. Bevollmächtigter ist Sony Deutschland GmbH, Hedelfinger Strasse 61, D-70327 Stuttgart. Für Service oder Garantieangelegenheiten wenden Sie sich bitte an die in separaten Service oder Garantiedokumenten angegebenen Adressen.

European Union Restriction of Hazardous Substances Directive compliant.

Entspricht der Richtlinie der Europäischen Union zur Beschränkung der Verwendung gefährlicher Stoffe.

VORSICHT

Für kunden in Deutshland

Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender / folgenden Umgebung(en):

• Wohngegenden

• Gewerbegebiete

• Leichtindustriegebiete

(Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B.)

IMPORTANT SAFEGUARDS

For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference.

Carefully observe all warnings, precautions and instructions on the appliance, or described in the operating instructions and adhere to them.

USE

Power Sources – This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of electrical power, consult your dealer or local power company.

For the unit with a three-wire grounding type ac plug:

If you are unable to insert the plug into the outlet, contact your electrician to have a suitable plug installed. Do not defeat the safety purpose of the grounding plug.

AC Power cord: (for AC mains operating unit only)

The AC power cord should have appropriate safety approvals or marking for the country in which the equipment will be used. Consult your dealer or local power company.

Cleaning – Unplug the unit from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the unit.

Object and Liquid Entry – Never push objects of any kind into the unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

INSTALLATION

Water and Moisture – Do not use power-line operated units near water – for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.

Power-Cord Protection – Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against it, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance.

Accessories – Do not place the unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury to a child or an adult, and serious damage to the unit. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer.

Ventilation – The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable operation of the unit, and to protect it from overheating, these slots and openings must never be blocked or covered.

• Never cover the slots and openings with a cloth or other materials.

• Never block the slots and openings by placing the unit on a bed, sofa, rug, or other similar surface.

• Never place the unit in a confined space, such as a bookcase, or builtin cabinet, unless proper ventilation is provided.

SERVICE

Damage Requiring Service – Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

• When the power cord or plug is damaged or frayed.

• If liquid has been spilled or objects have fallen into the unit.

• If the unit has been exposed to rain or water.

• If the unit has been subject to excessive shock by being dropped, or the cabinet has been damaged.

• If the unit does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to normal operation.

• When the unit exhibits a distinct change in performance - this indicates a need for service.

Servicing – Do not attempt to service the unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards.

Refer to all servicing to qualified service personnel.

Table of Contents

Overview .................................................................................................................. 6

Introduction .............................................................................................................. 6

About AIT Drives ............................................................................................ 6

Precautions ....................................................................................................... 8

Installation .............................................................................................................. 11

SCSI Connection/Setting the SCSI ID ...........................................................11

Option Switches (DIP Switch) ....................................................................... 12

Mounting Holes .............................................................................................. 15

Reconfiguring From 5.25" Model to 3.5" Model ........................................... 16

Orientation......................................................................................................16

Attaching and Removing the Dust Cover ............................................................... 17

Attaching the Dust Cover ............................................................................... 17

Removing the Dust Cover ..............................................................................18

Operation ................................................................................................................ 19

Location of 3 LEDs ........................................................................................19

Drive Operation .............................................................................................. 20

Emergency Tape Removal Procedure ............................................................22

Interface Implementation........................................................................................25

Supported SCSI Messages ............................................................................. 25

Supported SCSI Commands ........................................................................... 25

Specifications ......................................................................................................... 26

Product Specifications .................................................................................... 26

Sony Contacts .........................................................................................................28

• Sony cannot accept liability for data written to cartridges lost as a result of using this product.

• Sony bears no responsibility for any financial damages, lost profits, or claims made by third parties arising from the use of this product.

Overview

The SDX-1100V, SDX-900V, and SDX-800V series drives are high capacity data storage devices using Advanced Intelligent tape (AIT) technology. The SDX-1100V, SDX-900V, and SDX-800V series drives achieve high data reliability through Read-After-Write, an additional level of Error Correction Code, and other features.

The SDX-1100V, SDX-900V, and SDX-800V series drives store data on tape using standard formats called AIT (Advanced Intelligent Tape) and ALDC.

Introduction

About AIT Drives

The SDX-1100V Series AIT-5 Tape Drives are internal AIT drive units that use data cartridges conforming to the AIT-5 format. The SDX-900V Series AIT-4 Tape Drives are internal AIT drive units that use data cartridges conforming to the AIT-4 format. The SDX-800V Series AIT-3 Ex Tape Drives are internal AIT drive units that use data cartridges conforming to the AIT-3 Ex format.

The SDX-1100V series drives support the AIT-5, AIT-4, AIT-3 Ex, and AIT-3 formats. The SDX-900V series drives support the AIT-4 and AIT-3 Ex format. The SDX-800V series drives support the AIT-3 Ex, AIT-3, AIT-2 Turbo, AIT-2 (Read only), AIT-1 Turbo (Read only), AIT-1 (Read only), and AIT-E Turbo (Read only) formats.

Features

The SDX-1100V series drives have the following features:

• Supports reading and writing to data cartridges conforming to the AIT-5, AIT-4, AIT-3 Ex, and AIT-3 formats.

• The second-level error correction code guarantees high data reliability writing to data cartridges conforming to the AIT-5, AIT-4, and AIT-3 Ex formats.

• The third-level error correction code guarantees high data reliability writing to data cartridges conforming to the AIT-3 format.

• Data compression provides 1,040 gigabytes of storage on SDX5-400C data cartridges.* The native capacity is 400 gigabytes of storage on SDX5-400C data cartridges.

• Stored data are automatically checked for compression.

• Ultra 160 SCSI interface is fully supported for host computer access.

• Fragment rewrite function (AIT-5, AIT-4, AIT-3 Ex)

• Frame rewrite function (AIT-3)

The SDX-900V series drives have the following features:

• Supports reading and writing to data cartridges conforming to the AIT-4 and AIT-3 Ex formats.

• The second-level error correction code guarantees high data reliability writing to data cartridges conforming to the AIT-4 and AIT-3 Ex formats.

• Data compression provides 520 gigabytes of storage on SDX4-200C data cartridges. The native capacity is 200 gigabytes of storage on SDX4-200C data cartridges.

• Stored data are automatically checked for compression.

• Ultra 160 SCSI interface is fully supported for host computer access.

• Fragment rewrite function

This is assuming 2.6 : 1 compression ratio. The degree of data compression attained while recording data varies according to system environment and data type.

The SDX-800V series drives have the following features:

• Supports reading and writing to data cartridges conforming to the AIT-3 Ex, AIT-3, and AIT-2 Turbo formats.

• Supports reading from data cartridges conforming to the AIT-2, AIT-1 Turbo, AIT-1, and AIT-E Turbo formats.

• The second-level error correction code guarantees high data reliability writing to data cartridges conforming to the AIT-3 Ex format.

• The third-level error correction code guarantees high data reliability writing to data cartridges conforming to the AIT-3 format.

• Data compression provides 390 gigabytes of storage on SDX3X-150C data cartridges.

The native capacity is 150 gigabytes of storage on SDX3X-150C data cartridges.

• Stored data are automatically checked for compression.

• Ultra 160 SCSI interface is fully supported for host computer access.

• Fragment rewrite function (AIT-3 Ex)

• Frame rewrite function (AIT-3)

This is assuming 2.6 : 1 compression ratio. The degree of data compression attained while recording data varies according to system environment and data type.

Precautions

Installation

Avoid placing the drives in locations subject to:

– high humidity

– high temperature

– mechanical shock and vibration

– direct sunlight

For details, see “Specifications” on page 26.

Operation

• Do not move the drives while they are operating. It may cause malfunctions.

• Avoid exposing the drives to sudden changes from low to high temperatures. This may cause condensation to collect inside the drives. If the ambient temperature should suddenly rise while the drives are turned on, turn them off and wait at least one hour before turning them back on. If you attempt to operate the drives immediately after a sudden increase in temperature, malfunctions may occur.

• Turning off the power to the drives while they are writing to tape may cause the tape to become unreadable. All previously negotiated parameters will be lost, whenever power to the drives is cycled.

Transportation

• Keep the original packing materials to facilitate safe transportation of the drives.

• Always remove the tape/media cartridge before moving the drives. After removing the drives from the computer, repack them into their original packing.

Compatible Data Cartridges

The SDX-1100V series drives can be used with data cartridges marked with the AIT-5, AIT-4, AIT-3 Ex, or AIT-3 logo.

The SDX-900V series drives can be used with data cartridges marked with the AIT-4 or AIT-3 Ex logo.

The SDX-800V series drives can be used with data cartridges marked with the AIT-3 Ex, AIT-3, AIT-2 Turbo, AIT-2 (read only), AIT-1 Turbo (read only), AIT-1 (read only), or AIT-E Turbo (read only) logo.

AIT-E Turbo LOGO AIT-1 LOGO AIT-1 Turbo LOGO

AIT-2 LOGO AIT-2 Turbo LOGO AIT-3 LOGO

AIT-3 Ex LOGO AIT-4 LOGO AIT-5 LOGO

Caution

• Do not use cartridges other than the ones described above with this drive. Be sure to use only the cartridges designed specifically for AIT.

• Do not use anything but AIT cartridges with this drive, as doing so can damage the drive. Although commercially available 8 mm videotapes resemble AIT cartridges in appearance, they have entirely different specifications and cannot be used.

SCSI Termination

The SDX-1100V, SDX-900V, and SDX-800V series drives conform to the Microsoft PC97 standard, which requires the internal (naked) drive to be terminated with an external terminator.

Microsoft PC97 SCSI requirements

SCSI peripherals must not terminate the bus. Both internal and external cable ends are instead terminated by plug-in connectors.

Host Computer Wide SCSI

68-pin cable

SDX-1100V/SDX-900V/SDX-800V series drive

Example connection to the host computer and other peripheral devices

Terminator

Installation

SCSI Connection/Setting the SCSI ID

Rear view figures are examples of the SDX-1100V drive.

SCSI ID

210

SCSI ID

P.D.

N.C.

SCSI 68pin Connector

Jumpers

Power Connector

5 V

SCSI ID 3

SCSI ID 2

SCSI ID 1

SCSI ID 0

Parity Disable

No Connection

Parity

Disable

Enable

Note :

= CLOSED/Jumper

OPEN/Jumper not

installed

Don’

t care

Parity Disable Jumper

Parity check function can be disabled by Jumper. Parity check is disabled while left end jumper is installed. Parity generate function is always enabled.

1234

GND GND 12 V

Option Switches (DIP Switch)

DIP Switch Positions

Default

ON OFF

12345678

DIP Switch

1 DR (Disaster Recovery) Mode (OFF) 2 Emulation Mode (OFF) 3 AIT Library Interface Mode (ON) 4 Reserved (OFF) 5 Terminator Power (ON) 6 Periodic Cleaning Req (ON) 7 DC Control (1) (ON) 8 DC Control (2) (OFF)

Emulation Mode

To enable Emulation Mode, set the DIP switch 2 [Emulation Mode] to ON.

ON OFF

12345678

Emulation Mode for the SDX-1100V series drives return the following as the Product Identification field of the Inquiry command.

SDX-900V

Emulation Mode for the SDX-900V series drives return the following as the Product Identification field of the Inquiry command.

SDX-700C

Emulation Mode for the SDX-800V series drives return the following as the Product Identification field of the Inquiry command.

SDX-700C

AIT Library Interface Mode

To enable AIT Library Interface Mode, set DIP switch 3 [AIT Library Interface Mode] to ON.

ON OFF

12345678

When switch 3 is ON, AIT Legacy Library Interface Mode is enabled. With this switch OFF, ACI Mode is enabled.

Terminator Power

To enable terminator power, set DIP switch 5 [Terminator Power] to ON.

ON OFF

12345678

Periodic Cleaning Request Mode

To enable Periodic Cleaning Request Mode, set DIP switch 6 [Periodic Cleaning Req] to ON.

ON OFF

12345678

The “CLEANING REQUEST” LED on the front panel lights after every 100 hours of operation.

When this LED lights, clean the drive with a cleaning cartridge.

Note

To maintain the drive in optimum condition in environments affected by dust and other contaminants, we recommend keeping cleaning requests enabled.

Data Compression Control

Data compression can be selected by DIP switches. Data compression is enabled when DIP switch 7 [DC Control (1)] is ON.

ON OFF

12345678

Control by host can be disabled when DIP switch 8 [DC Control (2)] is ON.

ON OFF

12345678

Mounting Holes

The following figures apply to the SDX-800V series drives. However, the locations of the mounting holes for the other models are the same.

For 3.5" Standard Height

(Connecter Dimensions)

For 5.25" Half Height

(Connecter Dimensions)

Reconfiguring From 5.25" Model to 3.5" Model

You can reconfigure the 5.25" model to the 3.5" model yourself.

1 Remove the 2 screws for each side rail.

2 Take the side rail off.

Side Rail (L)

Side Rail (R)

Orientation

10 10

Attaching and Removing the Dust Cover

Attaching the Dust Cover

1 Align the dust cover’s hinge clips (one on each side) with the

pins of the drive bezel.

• The dust cover should be positioned so that the magnets* on the cover’s back face the drive bezel.

This magnet does not affect the tape of the cartridge.

• Holding the dust cover at an angle, as shown in the figure below, set the hinge clips on top of the bezel pins, positioning them so that they bracket the pins.

2 Press down at an angle on each side in turn until you hear

the hinge clips click into place.

Caution

Do not press the dust cover in horizontally from the front. Doing so could cause the dust cover to break.

3 Close the dust cover.

This completes attachment of the dust cover.

Removing the Dust Cover

1 Open the dust cover.

2 Holding the dust cover at both corners, carefully raise the

dust cover.

The dust cover hinge clips and drive bezel pins uncouple.

Note

We recommend that you use the drive with the dust cover.

Operation

Location of 3 LEDs

There are three LED indicators (TAPE MOTION LED, CLEANING REQUEST LED, REPLACE TAPE LED) and an EJECT button on the front panel of the SDX-1100V, SDX-900V, and SDX-800V series drives.

Front Panel

Advanced Intelligent Tap e

TAPE

MOTION

CLEANING REQUEST

REPLACE

TAPE

LED

LED Indication for Drive Status

The LED indicators are defined as follows

LED

TAPE CLEANING REPLACE

MOTION REQUEST TAPE

Independent Independent Tape loaded

Independent Independent Tape access in progress (write/read)

Independent Independent Tape access in progress (others)

Independent Independent Cleaning is requested

Independent Independent Cleaning is not completed

Independent Independent Media error occurred

H/W error occurred

Slow

1 pulse (0.9 sec on/0.3 sec off)

Fast

1 pulse (0.3 sec on/0.3 sec off)

Sense

EJECT button

Drive Operation

Loading a Cartridge

Note

While setting the data cartridge, do not turn off the host computer. This may cause a malfunction or damage data.

1 Turn on the host computer. Check that the drive’s TAPE

MOTION LED, CLEANING REQUEST LED and REPLACE TAPE LED go off.

2 Open the dust cover.

3 Set the AIT data cartridge orientation as shown here and

insert it into the data cartridge slot.

By fully inserting the data cartridge, it is automatically set in the drive and the TAPE MOTION LED lights.

Unloading a Cartridge

The cartridge can be removed from the SDX-1100V, SDX-900V, and SDX-800V series drives either in response to a SCSI Unload command, or by pressing the EJECT button.

When the EJECT button is pressed, the tape is rewound and the cartridge ejected from the slot.

Write-protecting a Cartridge

Cartridges can be write-protected by sliding the tab on the back of the cartridge. In this state, data can be read from the tape but not written onto it.

AIT-5 AIT-4 AIT-3 Ex AIT-3 AIT-2 Turbo

AIT-1

AIT-2 AIT-1 Turbo AIT-E Turbo

Using your fingernail, push the switch in the direction of the arrow to protect the tape from writing or accidental erasure.

Return the switch to its original position to re-enable writing.

Using a Cleaning Cartridge

To keep the AIT drive in top condition, clean the drive unit as needed using a cleaning cartridge with the AIT logo. When the drive unit needs cleaning, the CLEANING REQUEST indicator lights. (For the SDX-1100V, SDX-900V, and SDX-800V series drives, use the SDX-1100V, SDX-900V, and SDX-800V series cleaning cartridges respectively.)

Use the cleaning cartridge made exclusively for each model.

Cleaning cartridge to use

SDX-1100V SDX5-CL

SDX-900V SDX4-CL, SDX4-CLL

SDX-800V SDX3X-CL

How to Clean

1 Load the cleaning cartridge into the AIT drive. Cleaning

starts automatically.

2 Cleaning takes from a few seconds to a minute for the

SDX-1100V, SDX-900V, and SDX-800V *, and the cartridge is automatically ejected when finished.

The cleaning time varies depending on the condition of the drive.

Caution

Do not rewind the cleaning cartridge and reuse it. When you reach the end of the cartridge, dispose it and buy a new cleaning cartridge with the AIT logo.

Storage Precautions

• Keep cartridges in their cases when not in the drives.

• Avoid storing cartridges in dusty locations, in direct sunlight, near heaters or air conditioners, or in humid locations.

• Do not place cartridges on dashboards or in car storage trays.

Emergency Tape Removal Procedure

1 Remove the drive from the chassis or enclosure to allow

access to the bottom of the drive.

2 Remove the drive’s top cover.

3 Locate the small opening in the bottom of the drive and

insert the tip of a precision screwdriver so that the Loading motor shaft can be rotated.

4 Rotate the motor shaft clockwise to bring the threading

mechanism back to the initial position.

Reel motor

Loading motor

Emergency Tape Removal Procedure

Caution

Stop rotating the motor shaft immediately, when the Guide B gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise, the gears of the drive can be damaged.

Tape guide surface

The Initial Position of the Threading Mechanism

Guide B

detail A

Cartridge

Tape guide surface

5 Before the manual ejection procedure, tape slack must be

removed in order to prevent tape damage. Rotate the gear mechanism located on the bottom of the drive counterclockwise to tighten the tape.

6 After the tape slack has been removed, continue to turn the

Loading motor shaft located on the bottom of the drive clockwise with a precision screwdriver until the tape cartridge is lifted out of the drive mechanism and is ejected.

7 Return the drive to Sony for repair.

Interface Implementation

Supported SCSI Messages

Abort Identify

Target Reset Ignore Wide Residue

Command Complete Message Parity Error

Disconnect Message Reject

Extended Message No Operation

– Synchronous Data Transfer

Request

– Wide Data Transfer Request

– Parallel Protocol Request

Supported SCSI Commands

Erase

Inquiry

Load/Unload

Locate

Log Sense

Log Select

Mode Select (6)

Mode Select (10)

Mode Sense (6)

Mode Sense (10)

Persistent Reserve In

Persistent Reserve Out

Prevent Allow Medium Removal

Read

Read Attribute

Read Block Limits

Read Buffer

Read Position

Receive Diagnostic Result

Release (6)

Release (10)

Report Density Support

Report Device Identifier

Report Luns

Request Sense

Reserve (6)

Reserve (10)

Rewind

Send Diagnostic

Set Device Identifier

Space

Test Unit Ready

Write

Write Attribute

Write Buffer

Write Filemarks

Specifications

Product Specifications

Dimensions

(not including bezel and protruding parts)

3.5" 5.25" Height 41.2 mm (1.62 in) 41.2 mm (1.62 in) Width 101.6 mm (4.0 in) 146.0 mm (5.75 in) Depth 155.0 mm (6.1 in) 155.0 mm (6.1 in)

Mass

SDX-1100V

3.5" 0.8 kg (28.2 oz.)

5.25" 1.1 kg (38.8 oz.)

SDX-900V, SDX-800V

3.5" 780 g (27.5 oz.)

5.25" 1010 g (35.6 oz.)

Altitude

Operating 0 to 3048 m (0 to 10,000 ft.)

Vibration

Operating Swept Sine 5 to 500 Hz

*0.25 G Peak 1 Octave/min. 3 axes, 3 directions

Non-operating Swept Sine 5 to 500 Hz

*0.5 G Peak 1 Octave/min. 3 axes, 3 directions

Acoustic Noise (A) curve weight

Streaming Write/Read 35 dB (A) Insert/Eject 60 dB (A)

Note

The sound-meter on (A) scale is located 1m (3.3 ft.) in front of the center of the drive front panel.

Shock

Operating No Data Loss

Non-operating No Device Damage

Half Sine Performance

5 G Peak 3 ms 3 axes, 3 directions *Interval of 10 seconds

Half Sine 90 G Peak 3 ms (30 G Peak 11 ms) 3 axes, 3 directions *Interval of 10 seconds

Temperature and Humidity Range

Temperature

Operating 5 ˚C to 40 ˚C (∆T<10 ˚C/h) (41 ˚F to 104 ˚F (∆T<18 ˚F/h)) Non-operating (mech.) – 40 ˚C to 70 ˚C (∆T<20 ˚C/h) (– 40 ˚F to 158 ˚F (∆T<36 ˚F/h)) Non-operating (tape) – 40 ˚C to 45 ˚C (∆T<20 ˚C/h) (– 40 ˚F to 113 ˚F (∆T<36 ˚F/h))

Humidity

Operating 20 to 80% RH, non-condensing

Maximum wet bulb temperature : 26 ˚C (78.8 ˚F)

Non-operating (mech.) 5 to 95% RH (∆RH<30%/h)

Non-operating (tape) 20 to 80% RH (∆RH<30%/h)

Maximum wet bulb temperature : 45 ˚C (113 ˚F)

Air-cooling Requirement

Surrounding temperature < 40 ˚C (104 ˚F)

Clean air flow is recommended to minimize the possibility of data loss.

Power Requirements

SDX-1100V

Voltage Max Ripple

5 V +/– 5% 100 mVp-p 1.7 A 2.5 A

12 V +/– 10% 150 mVp-p 0.87 A 3.0 A

SDX-900V, SDX-800V

Voltage Max Ripple

5 V +/– 5% 100 mVp-p 1.5 A 2.5 A

12 V +/– 10% 150 mVp-p 0.75 A 3.0 A

Typical Maximum

Current

+ 61 hidden pages