Sony RM-PJHS2, SU-HS2 Service Manual

VIDEO PROJECTOR
VPL-HS3
PROJECTOR STAND
SU-HS2
REMOTE COMMANDER
RM-PJHS2
SERVICE MANUAL 1st Edition
! WARNING
This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement.
WARNING!!
AN INSULATED TRANSFORMER SHOULD BE USED DURING ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE­CAUSE OF LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE AC POWER LINE.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY A DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO­NENTS WITH SONY PARTS WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB­LISHED BY SONY.
!!
! MARK ON THE SCHEMA TIC
!!
ATTENTION!!
AFIN D’ÉVITER TOUT RISQUE D’ÉLECTROCUTION PROVENANT D’UN CHÂSSIS SOUS TENSION, UN TRANSFORMA TEUR D’ISOLEMENT DOIT ETRE UTILISÉ LORS DE TOUT DÉPANNAGE. LE CHÂSSIS DE CE RÉCEPTEUR EST DIRECTEMENT RACCORDÉ Á L’ALIMENTATION SECTEUR.
ATTENTION AUX COMPOSANTS RELATIFS Á LA
LES COMPOSANTS IDENTIFIÉS PAR UNE MAPQUE LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMÉRO DE PIÈCE EST INDIQUÉ DANS LE PRÉSENT MANUEL OU DANS DES SUPPLÉMENTS PUBLIÉS P AR SONY.
SÉCURITÉ!!
!!
! SUR
!!
For the customers in the Netherlands Voor de klanten in Nederland
Hoe u de batterijen moet verwijderen, leest u in de tekst van deze handleiding.
Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer oder nach längerer Gebrauchsdauer der Batterien nicht mehr einwandfrei funktioniert. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel.
VPL-HS3
1 (P)

Table of Contents

1. Service Overview
1-1. Appearance Figure ......................................................................................1-1
1-2. Board Locations ..........................................................................................1-1
1-3. Disassembly ................................................................................................1-2
1-3-1. Top Cover Assembly.................................................................. 1-2
1-3-2. NR, L, HA, HB Boards and Hood Assembly ............................1-3
1-3-3. Jog Unit Assembly .....................................................................1-4
1-3-4. DC Fan .......................................................................................1-4
1-3-5. U, NF Boards and Filter Assembly ............................................1-5
1-3-6. Blower Fan and Speaker ............................................................ 1-5
1-3-7. DC Fan and Lamp Fan Holder ...................................................1-6
1-3-8. B Board ...................................................................................... 1-6
1-3-9. Optics Block Assembly-1 and C Board .....................................1-7
1-3-10. Optics Block Assembly-2 .......................................................... 1-8
1-3-11. PS Converter and Main Mirror .................................................. 1-8
1-3-12. Relay-1 Lens and G-refrect Dichroic Mirror .............................1-9
1-3-13. Each Paet Direction of Optical Block ......................................1-10
1-3-14. Power Supply Block and G Board ...........................................1-11
1-3-15. F Board.....................................................................................1-12
1-3-16. Lamp House and Lamp Duct (TP), (BT) .................................1-13
1-3-17. QA Board .................................................................................1-14
1-3-18. Extension Board and Extension Connectors ............................1-15
1-3-19. Extension Board and Extension Connectors
Connection (C Board) ..............................................................1-16
1-3-20. Extension Board and Extension Connectors
Connection (B Board) ..............................................................1-17
1-3-21. Connection Example ................................................................1-18
1-4. Service Knowhow .....................................................................................1-19
1-4-1. After Replacing the Prism Block ............................................. 1-19
1-4-2. After Replacing the Board .......................................................1-19
1-5. Memory ..................................................................................................... 1-20
1-6. Warning on Power Connection .................................................................1-22
VPL-HS3
1
2. Electrical Adjustments
2-1. Preparations.................................................................................................2-1
2-1-1. Equipment Required................................................................... 2-1
2-1-2. Optical Unit Adjustment ............................................................2-1
2-1-3. Factory Mode Setting .................................................................2-1
2-2. V COM Adjustment ....................................................................................2-1
2-3. Adjustment Item Initialize Data ..................................................................2-3
2-4. White Balance Adjustment in Service ...................................................... 2-10
2-4-1. INPUT-A .................................................................................. 2-10
2-4-2. VIDEO ..................................................................................... 2-11
2-5. Tilt Adjustment ......................................................................................... 2-12
3. Semiconductors .................................................................................3-1
4. Spare Parts
4-1. Notes on Repair Parts..................................................................................4-1
4-2. Exploded Views ..........................................................................................4-2
4-2-1. Cover ..........................................................................................4-2
4-2-2. Chassis........................................................................................ 4-4
4-2-3. Base ............................................................................................4-6
4-2-4. Optics-1 ......................................................................................4-8
4-2-5. Optics-2 ....................................................................................4-10
4-2-6. SU-HS2 ....................................................................................4-12
4-3. Electrical Parts List ...................................................................................4-13
4-4. Packing Materials & Supplied Accessories .............................................. 4-30
4-5. SU-HS2 .....................................................................................................4-30
5. Block Diagrams
F ................................................................................................................5-1
G................................................................................................................ 5-1
B ................................................................................................................5-2
C ................................................................................................................5-4
HA.............................................................................................................5-4
HB .............................................................................................................5-4
L ................................................................................................................5-4
NR .............................................................................................................5-4
U................................................................................................................ 5-4
NF ............................................................................................................. 5-6
QA.............................................................................................................5-6
2
VPL-HS3
6. Diagrams
6-1. Frame Wiring ..............................................................................................6-1
6-2. Schematic Diagrams and Board Layouts ....................................................6-2
B ................................................................................................................6-3
C ..............................................................................................................6-13
F ..............................................................................................................6-24
G.............................................................................................................. 6-26
HA...........................................................................................................6-29
HB ........................................................................................................... 6-30
L ..............................................................................................................6-31
NF ........................................................................................................... 6-31
NR ........................................................................................................... 6-32
QA...........................................................................................................6-33
U.............................................................................................................. 6-39
VPL-HS3
3

1-1. Appearance Figure

Section 1

Service Overview

1-2. Board Locations

F
Power supply block (Lamp)
G
BC
HB
NR
L
QA
VPL-HS3
HA
U
NF
1-1

1-3. Disassembly

1-3-1. Top Cover Assembly

2 Open the top cover assembly in the direction of the arrow B.
3 Remove the top cover assembly in the direction of the arrow C.
B
A
1 Turn the screw of the RE holder assembly
in the direction of the arrow A.
1-2
C
VPL-HS3

1-3-2. NR, L, HA, HB Boards and Hood Assembly

!\ Hood assembly
!- Button (H) holder
!] HA board
8 T wo screws
(+PWHPT 3x8)
CN81
CN82
CN83
2 Hood assembly
4 L board
Claw
7 HB board
7 Sheet (2)
!/ T wo screws
(+PWHPT 3x8)
![ Button (P)
CN61
!= Button (H)
HB board
CN601
VPL-HS3
3 Sheet (1)
1 Six screws
(+B 3x6)
C board
5
Screw (+B 3x6)
6 NR board
1-3

1-3-3. Jog Unit Assembly

2
Jog unit assembly
Claw
Lens
1
Three screws (+B 3x6)
Precaution during jog unit assembly installation
3 Turn over the zoom cover, focus cover Jog unit assembly (Roller)
in the direction of the arrow.

1-3-4. DC Fan

. Remove the jog unit assembly. (Refer to 1-3-3.)
2
Remove the duct (G)
in the direction of the arrow.
CN612
C board
1
Two screws (+B 3x6)
4
DC fan
3
Fan cushion
1-4
VPL-HS3

1-3-5. U, NF Boards and Filter Assembly

1 T wo screws
(+B 3x6)
2 Filter cover assembly, Filter assembly, Duct (IN)
7 Filter cover assembly
3 Screw
(+B 3x6)
U board
CN41
4 NF board

1-3-6. Blower Fan and Speaker

. Remove the jog unit assembly. (Refer to 1-3-3.) . Remove the filter assembly. (Refer to 1-3-5.)
2
Remove the blower fan, prism fan holder
in the direction of the arrow.
CN011
1
Two screws (+B 3x6)
5 Screw
(+B 3x6)
6 U board
8 Filter assembly
!/ Duct (IN)
9 Packing (IN)
6 Two screws
(+PSW 3x25)
7 Blower fan
VPL-HS3
Connector (3P)
Claw
8 Prism fan
holder
3
Three screws (+B 3x6)
4
Speaker spring assembly
5
Speaker
1-5

1-3-7. DC Fan and Lamp Fan Holder

1 T wo screws
(+B 3x6)
Connector (3P)

1-3-8. B Board

6
5 T wo screws
(+PSW 3x20)
Connector (3P)
DC fan
Lamp fan holder
2
4
DC fan
3 T wo screws
(+PSW 3x20)
1
Two screws
(+B 3x6)
2
Holder (B)
3
B board
CN151
Flat connector assembly CN101
(50P)
QA board
CN104
CN105
CN103 (board to board)
CN104 (board to board)
Flat connector assembly CN102
(50P)
QA board CN104 CN105
B board
1-6
VPL-HS3

1-3-9. Optics Block Assembly-1 and C Board

. Remove the jog unit assembly. (Refer to 1-3-3.)
Two flat connectors assembly (50P)
CN102
CN606
CN612
1
Remove the harneses
CN101
CN602
CN610
CN609
CN603
B board
C board
CN752
5
Three screws
(+B 3x6)
Two flat connectors assembly (50P)
CN802
CN502
CN501
CN503
CN852
6
C board
7
Optics block
assembly-1
2
Four screws
(+P M4x12)
3
Light guard
4
Optics block assembly-1,
C board
CN605
CN607
VPL-HS3
1-7

1-3-10. Optics Block Assembly-2

. Remove the optics block assembly-1. (Refer to 1-3-9.)
Loosen the screw.
3
5
Four screws
(+PSW 3x8)
2 Remove the aperture unit in the direction of the arrow.
1
Two screws
(+PSW 3x8)

1-3-11. PS Converter and Main Mirror

4 Lamp assembly
7 Optisc block assembly-2
6 Frame base, P
Prims block assembly
rojection lens assembly,
. Remove the optics block assembly-1. (Refer to 1-3-9.)
1
Two screws
(+B 3x6)
4 Unit cover (R)
6 PS com aperture
5 PS converter
2 Remove the aperture unit
in the direction of the arrow.
3
Two screws
(+B 3x6)
Marking
9 Lens-1 fly eye
8 UV-PRE-CUT filter
7 Lens-2 fly eye
0 Three main mirror
fasteners (A)
!=
Main mirror
!-
fastener (B)
Marked side
Main mirror
1-8
Note: Marked with indicates as shown beloe.
Projection side
Flat side
VPL-HS3

1-3-12. Relay-1 Lens and G-refrect Dichroic Mirror

. Remove the optics block assembly-1. (Refer to 1-3-9.)
!=
R-channel-1 mirror,
Marking side
![
Relay-1 lens
Marking side
1
Five screws
(+B 3x6)
2
Unit cover (F)
!]
G-refrect dichroic mirror
9 G-CH condenser lens
!-
Relay-2 lens
0 R-channel-2 mirror
Marking side
8 R-CH condenser lens
7 B-CH condenser lens
3 Main condenser lens
Marking side
4 B-trans dichroic mirror
5 UV-cut filter
6 B-channel,
Marking side
Unit base
VPL-HS3
Note: Marked with indicates as shown beloe. Flat sideProjection side
1-9

1-3-13. Each Part Direction of Optical Block

Marking side
R-channel-2 mirror
R-CH condenser lens
G-CH condenser lens
Relay-2 lens
Marking side
Marking side
R-channel-1 mirror
G-refrect dichroic mirror
Relay-1 lens
Main condenser lens
UV-PRE-CUT filter
Lens-1 fly eye
B-CH condenser lens
B-channel
Marking side
Note: Marked with indicates as shown below. Flat sideProjection side
UV cut filter
B-trans dichroic mirror
Marking side
PS converter
Lens-2 fly eye
PS com aperture
Marking side
1-10
VPL-HS3
3
Two screws
(+B 3x6)
7
Screw
(+PSW 3x8)
8
Earth plate (G)
!= Remove the G board
in the direction of the arrow
C
.
!- GL sheet
A
B
5
Four claws
Power supply block
Power Supply Block
G Board
Power block assembly
0
G holder assembly
1
Two screws
(+B 3x6)
2
Holder (B)
CN1
CN1
CN708
Three claws
CN709
CN710
CN601
CN602
9
CN1 (5P)
C
4
Remove the power block assembly
in the direction of the arrow
A
.
6
Remove the Power supply block
in the direction of the arrow
B
.

1-3-14. Power Supply Block and G Board

VPL-HS3
1-11

1-3-15. F Board

. Remove the holder (B), power supply. (Refer to 1-3-14.)
1
Two screws (+B 3x6)
6
Cap type cover capacitor
7
Remove the F board
in the direction of the arrow.
3
F sheet
2
G shield assembly, Heat sheet, Sheet G
4
Two screws (+B 3x6)
5
AC holder
1-12
VPL-HS3

1-3-16. Lamp House and Lamp Duct (TP), (BT)

To remove the Lamp duct (TP) (BT) and Lamp house, remove the related parts beforehand.
3
Optics block assembly-1,C board
1
Jog unit assembly
(Refer to 1-3-3.)
4 (Refer to 1-3-6.)
(Refer to 1-3-9.)
2 Filter cover assembly, Filter assembly, Duct (IN) (Refer to 1-3-5.)
Blower fan, Prism fan holder
5
Two screws (+B 3x6)
6
Lamp house
7
Three screws
(+B 3x6)
8
Lamp duct
Lamp fan holder
Two DC fans
(TP) (BT),
Lamp house
![
,
Thermo stud
0
9
Two screws (+PSW 3x8)
Two screws
!-
(+PSW 3x8)
Connector
!=
VPL-HS3
1-13

1-3-17. QA Board

To remove the QA board, remove the related parts beforehand.
1
3
G shield assembly
(Refer to 1-3-15.)
2
B board
(Refer to 1-3-8.)
4
Jog unit assembly
(Refer to 1-3-3.)
Holder (B)
(Refer to 1-3-8.)
6 Filter cover assembly, Filter assembly, Duct (IN) (Refer to 1-3-5.)
7 Prism fan holder (Refer to 1-3-6.)
Blower fan,
5
Optics block assembly-1, C board
(Refer to 1-3-9.)
9
Lamp duct
Lamp fan holder
Two DC fans
(TP), (BT),
,
(Refer to 1-3-16.)
8
Lamp house
(Refer to 1-3-16.)
Remove the QA board
!=
in the direction of the arrow.
0
Three screws
(+B 3x6)
!- Two screws
(+M 1.6x5)
1-14
VPL-HS3

1-3-18. Extension Board and Extension Connectors

n
Circled numbers on the pages from 1-16 to 1-18 are corresponded to the following extension tools.
X1 board
X3 board
X4 boardX4 board
1 Three flat cables (32P)
2
SR connector W (2P)
3
ZH connector R (3P)
ZH connector B (3P)
4
SR connector W (4P)
5
ZH connector W (4P)
6
7 SR connector W (5P)
X4 board
X2 board
8
ZH connector W (6P)
ZH connector W (11P)
9
0
SR connector W (12P)
Five flat cables (50P)
!-
ZH connector W (12P)
!=
VPL-HS3
X kit assy (A-1606-642-A)
1-15

1-3-19. Extension Board and Extension Connectors Connection (C Board)

n
The following circled numbers correspond to the extension tools on page 1-15.
DC fan
G
Power supply block (Lamp)
CN1
1
CN852
CN710
CN709
CN108
From prism block assy
7 3
CN612
CN752
CN606
CN602CN612
CN111
CN852
2
CN606
CN602 CN110
CN802
0
CN601
CN802
CN601
CN113
!-
CN101
CN103
X1
CN102
C
CN502CN501
CN102
CN101
CN610
8
CN610
CN107
CN609
CN609
CN106
5
4
CN112
CN607
CN605
CN603
CN105
6
9
B
CN021
NR
CN603
CN81
HB
1-16
CN41
FRONT
CN752
U
Blower fan
DC fan DC fan
VPL-HS3

1-3-20. Extension Board and Extension Connectors Connection (B Board)

n
The following circled numbers correspond to the extension tools on page 1-15.
CN708
G
!=
!-
CN65CN63
CN62
X2
CN102
CN64
CN104
QA
CN151
CN61
CN105
C
CN501 CN502
CN101
!-
B
CN104
CN72
CN73
CN71
CN103
CN74
X3
CN75
VPL-HS3
FRONT
1-17

1-3-21. Connection Example

n
The following circled numbers correspond to the extension tools on page 1-15.
For C Board
9
For B Board
3
7
1
6
B
G
!-
5
4
C
8
X1
0
2
1-18
QA
C
!=
G
!-
X2
B
!-
X3
VPL-HS3

1-4. Service Knowhow

1-4-1. After Replacing the Prism Block

1. Perform Section “2-2. V COM Adjustment.”
2. Perform the Gamma data writing of the Prism Block.
3. Perform Section “2-4. White Balance Adjustment on Servicing.”

1-4-2. After Replacing the Board

. Refer to the cross table shown on right. . There are no need to perform the adjustment when the board
other than the B board or C board had been replaced.
1) When Replacing the B Board
When the data before replacement can be read properly
1. Make a note of the data described in the cross table of board replacement, write the data into the new board with service mode.
2. If the white balance is extremely deteriorated, perform the white balance adjustment (Refer to Section 2-4.).
When the data before replacement cannot be read
1. Perform Section “2-2. V COM Adjustment.”
2. Perform Section “2-4. White Balance Adjustment on Servicing.”
3. Perform Section “2-5. Tilt Adjustment.”
2) When Replacing the C Board
1. Before replacement, unsolder the IC706 from the replaced C board and then mount it to the new board.
2. Perform Section “2-2. V COM Adjustment.”
3. If the white balance is extremely deteriorated, perform the white balance adjustment (Refer to Section 2-4.).
4. Perform Section “2-5. Tilt Adjustment.”
3) When Replacing the Other Board
There are no need to perform the adjustment.
Cross Table of Board Replacement
Board Name
Device Name Item Name B C
OTHER TILT C0 * O
TILT C1 * O TILT C2 * O
P.DRV VCOM (R) * O
VCOM (G) * O
VCOM (B) * O W/B ADJUST INPUT-A HIGH GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
INPUT-A LOW GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
INPUT-A MID GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
VIDEO MID GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
VIDEO HIGH GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
VIDEO LOW GAIN R * O
GAIN G * O GAIN B * O
BIAS R * O BIAS G * O BIAS B * O
VPL-HS3
* : When down the data before replacement, and then
write in the data after the board replacement.
O : Need adjustment
1-19

1-5. Memory

Memory structure consists of the following five memory blocks.
1. Set memory
2. Status memory
3. Chroma memory
4. W/B memory
5. Channel memory
6. Image Flip memory
7. Picture memory
CPU internal ROM : 384 kbyte Flash Memory CPU internal RAM : 32 kbyte External NVM memory : 8 kbyte EEPROM
Set Memory Set Memory Set Memory
Status Memory
No.01
Status Memory
No.02 No.03 No.04
...
No.99
Gamma memory is actualized through Gamma mode functionsoffsetting the output values to the Contrast and Brightness devices. When the power plug is connected to the power line (Standby status), all data inside the internal ROM are written into the NVM (Nonvolatile Memory). When the power is turned to on, required data for the current picture, such as status memory data, etc., are selected, and they are written into the internal RAM. When adjustment is carried out, adjustment data are written into the NVM automatically (items on the user mode) or by the trigger of memory operation (items on the service mode and special service mode), then stored them. Adjustable items (W/B and Device Adjust) of the service mode and special service mode are memorized into the NVM by the memory operation. At the same time, the factory preset (adjusted) data are all eliminated from the memory.
Input-A
Preset
Input-A
User
HDMI
No.01 No.02
No.03 No.04
...
No.99
No.101
...
No.120
No.03 No.04
...
No.99
Status Memory
1-20
Chroma Memory
W/B Memory
NT358/443/BW60
PAL/PAL-M/N/ SECAM/BW50
15k RGB
Component (15k)
Two times speed
Component
HDTV (YPbPr)
HDTV (GBR)
(Include two times speed)
Computer
Others
High
Middle
Low
High
Middle
Low
Chroma Memory
W/B Memory
NT358/443/BW60
PAL/PAL-M/N/ SECAM/BW50
15k RGB
Component (15k)
Two times speed
Component
HDTV (YPbPr)
HDTV (GBR)
(Include two times speed)
Computer
Others
High
Middle
Low
High
Middle
Low
Chroma Memory
W/B Memory
High
Middle
Low
VPL-HS3
Channel Memory
Video
S Video
Input-A
Video 2
S Video 2
Channel Memory
Video 1
S Video 1
Input-A
Video 2
S Video 2
HDMI HDMI
Channel Memory
Image Flip Memory
Picture Memory
Turn over to the upper and lower sides
No turn over to the upper and lower sides
Dynamic
Video 1
Standard Cinema User1 User2 User3 Dynamic
S Video 1
Standard Cinema User1 User2 User3 Dynamic
Input-A
Standard Cinema User1 User2 User3 Dynamic
Video 2
Standard Cinema User1 User2 User3 Dynamic
S Video 2
Standard Cinema User1 User2 User3 Dynamic Standard
HDMI
Cinema User1 User2 User3
Image Flip Memory
Picture Memory
Turn over to the upper and lower sides
No turn over to the upper and lower sides
Dynamic
Video 1
Standard Cinema User1 User2 User3 Dynamic
S Video 1
Standard Cinema User1 User2 User3 Dynamic
Input-A
Standard Cinema User1 User2 User3 Dynamic
Video 2
Standard Cinema User1 User2 User3 Dynamic
S Video 2
Standard Cinema User1 User2 User3
Image Flip Memory
Picture Memory
VPL-HS3
CPU ROM
Initialize
External NVM
CPU RAM
Memory
Active memory copy
1-21

1-6. Warning on Power Connection

Use a proper power cord for your local power supply.
The United States, Continental UK Australia Japan Canada Europe
Plug type YP-11 YP-21 SP-61 B8 YP-13 Female end YC-13L YC-13L YC-13L C7-2 YC-13L Cord type SPT-2 H03VVH2-F H03VVH2-F H03VVH2-F VCTFK Rated Voltage & Current 10 A/125 V 2.5 A/250 V 2.5 A/250 V 2.5 A/125 V 7 A/125 V Safety approval UL/CSA VDE BS SAA DENANHO Cord length (max.) 4.5 m
1-22
VPL-HS3
Loading...
+ 96 hidden pages