To reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
To avoid electrical shock, do not
open the cabinet. Refer serv icing to
qualified personnel only.
The mains lead must be changed
only at a qualified service shop.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the laser
protective housing inside the
enclosure.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this DVD recorder is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
Notice for customers in the
United Kingdom and
Republic of Ireland
A molded plug complying with
BS1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug
supplied need to be replaced, a 5
AMP fuse approved by ASTA or
BSI to BS1362, (i.e., marked with
or mark) must be used.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
Precautions
• This unit operates on 220 –
240 V AC, 50/60 Hz. Check that
the unit’s operating voltage is
identical with your local power
supply.
• To prevent fire or shock hazard,
do not place objects filled with
liquids, such as vases, on the
apparatus.
• Install this system so that the
mains lead can be unplugged
from the wall socket
immediately in the event of
trouble.
VIDEO Plus+ and PlusCode are
registered trademarks of Gemstar
Development Corporation.
The VIDEO Plus+ system is
manufactured under license from
Gemstar Development
Corporation.
Disposal of Old Electrical
& Electronic Equipment
(Applicable in the
European Union and
other European countries
with separate collection
systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic
equipment. By ensuring th is
product is disposed of correctly,
you will help prevent potential
negative consequences for the
environment and human health,
which could otherwise be caused
by inappropriate waste handling of
this product. The recycling of
materials will help to conserve
natural resources. For more
detailed information about
recycling of this product, please
contact your local Civic Office,
your household waste disposal
service or the shop where you
purchased the product.
This label is located on the laser
protective housing inside the
enclosure.
2
Precautions
This equipment has been tested
and found to comply with the
limits set out in the EMC
Directive using a connection
cable shorter than 3 metres.
On safety
Should any solid object or liquid
fall into the cabinet, unplug the
recorder and have it checked by
qualified personnel before
operating it any further.
On power sources
• The recorder is not
disconnected from the AC
power source (mains) as long
as it is connected to the wall
outlet, even if the recorder
itself has been turned off.
• If you are not going to use the
recorder for a long time, be
sure to dis connect the recorder
from the wall outlet. To
disconnect the AC power cord
(mains lead), grasp the plug
itself; never pull the cord.
On placement
• Place the recorder in a location
with adequate ventilation to
prevent heat build-up in the
recorder.
• Do not place the recorder on a
soft surface such as a rug that
might block the ventilation
holes.
• Do not place the recorder in a
confined space such as a
bookshelf or similar unit.
• Do not place the recorder in a
location near heat sources, or
in a place subject to direct
sunlight, excessive dust, or
mechanical shock.
• Do not place the recorder in an
inclined position. It is
designed to be operated in a
horizontal position only.
• Keep the recorder and discs
away from equipment with
strong magnets, such as
microwave ovens, or large
loudspeakers.
• Do not place heavy objects on
the recorder.
On recording
Make trial recordings before
making the actual recording.
On compensation for lost
recordings
Sony is not liable and will not
compensate for any lost
recordings or relevant losses,
including when recordings are
not made due to reasons
including recorder failure, or
when the contents of a recording
are lost or damaged as a result of
recorder failure or repair
undertaken to the recorder. Sony
will not restore, recover, or
replicate the recorded contents
under any circumstances.
Copyrights
• Television programmes, film s,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of
such material may be contrary
to the provisions of the
copyright laws. Also, use of
this recorder with cable
television transmission may
require authorization from the
cable television transmitter
and/or programme owner.
• This product incorporates
copyright protection
technology that is protected by
U.S. patents and other
intellectual property rights.
Use of this copyright
protection technology must be
authorized by Macrovision,
and is intended for home and
other limited viewing uses
only unless otherwise
authorized by Macrovision.
Reverse engineering or
disassembly is prohibited.
Copy guard function
Since the recorder has a copy
guard function, programmes
received through an external
tuner (not supplied) m ay contain
copy protection signals (copy
guard function) and as such may
not be recordable, depending on
the type of signal.
IMPORTANT NOTICE
Caution: This recorder is
capable of holding a still
video image or on-screen
display image on your
television screen
indefinitely. If you leave the
still video image or onscreen display image
displayed on your TV for an
extended period of time you
risk permanent damage to
your television screen.
Plasma display panels and
projection televisions are
especially susceptible to this.
If you have any questions or
problems concerning your
recorder, please consult your
nearest Sony dealer.
About this manual
• In this manual, “disc” is used
as a general reference for the
DVDs or CDs unless
otherwise specified by the text
or illustrations.
• Icons, such as , listed
at the top of each explanation
indicate what kind of media
can be used with the function
being explained.
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar
names as those on the remote.
• The on-screen display
illustrations used in this
manual may not match the
graphics displayed on your TV
screen.
• The explanations regarding
DVDs in this manual refer to
DVDs created on this recorder.
The explanations do not apply
to DVDs that are created on
other recorders and played
back on this recorder.
• 8x-speed or slower DVD+R DL (Double
Layer) discs
“DVD+RW,” “DVD+R,” and “DVD+R DL” are
trademarks.
Discs that cannot be recorded on
• 8 cm discs
• DVD-R DL (Dual Layer) discs
• DVD-RWs/DVD-Rs
Formatting
(new discs)
Automatically
formatted in
+VR mode
(DVD+RW
VIDEO)
Automatically
formatted in
+VR mode
(DVD+R
VIDEO)
Compatibility with other
DVD players (finalising)
Playable on DVD+RW
compatible players
(automatically finalised)
Playable on most DVD
players (finalisation
necessary) (page 34)
,continued
7
Playable discs
TypeDisc Logo
DVD VIDEO
DVD-RW/DVD-R
VIDEO CD
CD
DATA CD—
Icon used in
this manual
DVD
-
RWVR
-
RW
Video
-
RVR
-
R
Video
VCD
CD
DATA CD
Characteristics
Discs such as movies that can be
purchased or rented
This recorder also recognizes DVD-R
Dual Layer (Video mode) discs as DVD
Video compatible discs.
DVD-RW/DVD-R discs that were
recorded and finalised on other
equipment
VIDEO CDs or CD-Rs/CD-RWs in
VIDEO CD/Super VIDEO CD format
Music CDs or CD-Rs/CD-RWs in
music CD format
CD-ROMs/CD-Rs/CD-RWs
containing MP3 audio tracks
8 cm DVD+RW/
DVD-RW/DVD-R
“DVD VIDEO,” “CD,” “DVD-RW,” and
“DVD-R” are trademarks.
——
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are
recorded in a format different from the
formats mentioned in the table above.
• Data part of CD-Extras
• DVD-ROMs/DVD+RWs/DVD-RWs/
DVD+Rs/DVD-Rs that do not contain
DVD Video.
• DVD Audio discs
8
8 cm DVD+RW, DVD-RW, and
DVD-R recorded with a DVD video
camera
(Still images recorded with a DVD
video camera cannot be played.)
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
(page 9).
• DVDs that were recorded on a different
recorder and not correctly finalised.
Maximum recordable number of titles
DiscNumber of titles*
DVD+RW/DVD+R49
DVD+R DL49
* The maximum length for one title is eight hours.
Note on playback operations of DVD
VIDEOs/VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by
software producers. Since this recorder plays
DVD VIDEOs/VIDEO CDs according to the
disc contents the software producers
designed, some playback features may not be
available. See the instructions supplied with
the DVD VIDEOs/VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on
the rear of the unit and will only play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
DVD VIDEOs labelled will also play
ALL
on this recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region
code.” will appear on the TV screen.
Depending on the DVD VIDEO, no region
code indication may be labelled even though
playing the DVD VIDEO is prohibited by
area restrictions.
Region code
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does
not conform to the Compact Disc (CD)
standard, playback on this product is not
guaranteed.
b Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs, or CD-RWs/CD-Rs cannot be played on this
recorder due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software. The
disc will not play if it has not been correctly
finalised. For more information, see the operating
instructions for the recording device.
• You cannot shorten the time required for
recording even with high-speed discs.
• It is recommended that you use discs with “For
Video” printed on their packaging.
• You cannot add new recordings to DVD+Rs that
contain recordings made on other DVD
equipment.
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings
made on other DVD equipment. If you do add a
new recording, note that this recorder will rewrite
the DVD menu.
• You cannot edit recordings on DVD+RWs or
DVD+Rs that are made on other DVD
equipment.
• If the disc contains PC data unrecognizable by
this recorder, the data may be erased.
• You may not be able to record on some
recordable discs, depending on the disc.
Music discs encoded with copyright
protection technologies
This product is designed to play back discs
that conform to the Compact Disc (CD)
standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please
be aware that among those discs, there are
some that do not conform to the CD standard
and may not be playable by this product.
9
Hookups and Settings
Hooking Up the Recorder
Follow steps 1 through 6 to hook up and adjust the settings of the recorder. Do not connect the
mains lead until you reach “Step 4: Connecting the Mains Lead” on page 14.
b Notes
• See “Specifications” (page 78) for a list of supplied accessories.
• Plug in cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this recorder to a TV that does not have a SCART or video input jack.
• Be sure to disconnect the mains lead of each component before connecting.
Step 1: Connecting the Aerial Cable
Connect the aerial cable by following the steps below.
to AERIAL IN
TV
to AERIAL OUT
Aerial cable (supplied)
: Signal flow
DVD recorder
1 Disconnect the aerial cable from your TV, and connect it to AERIAL IN on the rear
panel of the recorder.
2 Connect AERIAL OUT of the recorder to the aerial input of your TV using the supplied
aerial cable.
10
Step 2: Connecting the Video Cords
Select one of the following patterns, A through D, according to the input jack on your TV
monitor, projector, or AV amplifier (receiver). This will enable you to view pictures.
B
INPUT
VIDEO
L
AUDI O
R
TV, projector, or AV
amplifier (receiver)
to LINE 2 OUT (VIDEO)
Audio/video cord
(not supplied)
SCART cord
(not supplied)
(yellow)
A
TV
to i LINE 1 – TV
Hookups and Settings
Y
B/CB
R/CR
(red)(blue)
to COMPONENT
VIDEO OUT
Component video
cord (not supplied)
(green)
D
(green)
(blue)
(red)
COMPONENT
VIDEO IN
P
P
TV, projector, or AV
amplifier (receiver)
: Signal flow
A SCART input jack
When you set “Easy Setup - Line1 Output” to
“S Video” or “RGB” (page 18), use a
SCART cord that conforms to the selected
signal.
B Video input jack
You will enjoy standard quality images.
C S VIDEO input jack
You will enjoy high quality images.
DVD recorder
to LINE 2 OUT (S VIDEO)
S-video cord
(not supplied)
INPUT
S VIDEO
TV, projector, or AV
amplifier (receiver)
C
D Component video input jacks (Y, PB/CB,
P
R/CR)
You will enjoy accurate colour reproduction
and high quality images.
If your TV accepts progressive 525p/625p
format signals, you must use this connection
and set “Component Out” in the “Video”
setup to “On” (page 62). Then set
“Progressive Output” to “On” in the “Video”
setup to send progressive video signals. For
details, see “Progressive Output” on page 62.
,continued
11
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the picture size, see
page 61.
If you are connecting to a VCR
Connect your VCR to the LINE 3/
DECODER jack on the recorder (page 19).
b Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same
time.
• When you connect the recorder to yo ur TV via the
SCART jacks, the TV’s input source is set to the
recorder automatically when you start playback.
If necessary, press TV t to return the input to
the TV.
• For correct SMARTLINK connection, you will
need a SCART cord that has the full 21 pins.
Refer to your TV’s instruction manual as well for
this connection.
• If you connect this recorder to a TV with
SMARTLINK, set “Easy Setup - Line1 Output”
to “Video.”
About the SMARTLINK
features (for SCART
connections only)
If the connected TV (or other connected
equipment such as a set top box) complies
with SMARTLINK, NexTView Link
MEGALOGIC
CINEMALINK*2, Q-Link*3, EURO VIEW
*4
LINK
*1
, EASYLINK*2,
, or T-V LINK*5, you can enjoy the
following SMARTLINK features.
• Preset Download
You can download the tuner preset data
from your TV to this recorder, and tune the
recorder according to that data in “Easy
Setup.” This greatly simplifies the “Easy
Setup” procedure. Be careful not to
disconnect the cables or exit the “Easy
Setup” function during this procedure
(page 18).
• TV Direct Rec
You can easily record what you are
watching on your TV (page 27).
• One Touch Play
You can turn on the recorder and TV, set the
TV’s input to the recorder, and start
playback with one touch of the H (play)
button (page 47).
*3
,
• One Touch Menu
You can turn on the recorder and TV, set the
TV to the recorder’s programme position,
and display the Title List menu with one
touch of the TITLE LIST button (page 47).
• One Touch Timer
You can turn on the recorder and TV, set the
TV to the recorder’s programme position,
and display the timer programming menu
with one touch of the TIMER button
(page 39).
• Automatic Power Off
The recorder will turn off automatically if
the recorder is not used after you turn off
the TV.
• NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
See your TV’s instruction manual.
*1
“MEGALOGIC” is a registered trademark of
Grundig Corporation.
*2
“EASYLINK” and “CINEMALINK” are
trademarks of Philips Corporation.
*3
“Q-Link” and “NexTView Link” are trademarks
of Panasonic Corporation.
*4
“EURO VIEW LINK” is a trademark of Toshiba
Corporation.
*5
“T-V LINK” is a trademark of JVC Corporation.
z Hint
SMARTLINK also works with TVs or other
equipment having EPG Timer Control, EPG Title
Download, and Now Recording functions. For
details, refer to the operating instructions supplied
with your TV or other equipment.
b Notes
• The SMARTLINK features are available only
when “Video” is selected in “Line1 Output.”
• The SMARTLINK features are not available
while the power is off when “Power save
standby” is set to “On” (page 69).
• Not all TVs respond to the functions above.
12
Step 3: Connecting the Audio Cords
Select one of the following patterns, A or B, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver). This will enable you to listen to sound.
[Speakers]
Rear (L)
Front (L)
AV amplifier (receiver)
with a decoder
[Speakers]
Rear (R)
Front (R)
A
Hookups and Settings
Centre
to DIGITAL OUT (COAXIAL)
to LINE 2 OUT (R-AUDIO-L)
Audio/video cord
(white)
(red)
(yellow)*
: Signal flow
* The yellow plug is used for video signals (page 11).
(not supplied)
Subwoofer
to coaxial digital input
Coaxial digital cord (not supplied)
DVD recorder
INPUT
(yellow)
(white)
(red)
TV, projector, or AV
amplifier (receiver)
B
VIDEO
L
AUDIO
R
A Digital audio input jack
If your AV amplifier (receiver) has a Dolby*1
Digital, DTS
*2
, or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effects.
B Audio L/R (left/right) input jacks
This connection will use your TV’s or stereo
amplifier’s (receiver’s) two speakers for
sound.
z Hint
For correct speaker location, see the operating
instructions supplied with the connected
components.
,continued
13
b Notes
• Do not connect your TV’s audio output jacks to
the LINE IN (R-AUDIO-L) jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
• With connection B, do not connect the LINE IN
(R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L)
jacks to your TV’s audio output jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
• With connection A, after you have comple ted the
connection, make the appropriate settings under
“Easy Setup - Audio Connection” (page 18).
Otherwise, no sound or a loud noise will come
from your speakers.
*1
Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Step 4: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the
recorder and TV mains leads (power cords)
into the mains. After you connect the mains
lead, you must wait for a short while before operating the recorder. You can
operate the recorder once the front panel
display lights up and the recorder enters
standby mode.
If you connect additional equipment to this
recorder (page 19), be sure to connect the
mains lead after all connections are complete.
~ AC IN
1
to AC IN
2
to mains
14
Step 5: Preparing the
Remote
You can control the recorder using the
supplied remote. Insert two R6 (size AA)
batteries by matching the 3 and # ends on
the batteries to the markings inside the
battery compartment. When using the
remote, point it at the remote sensor on the
recorder.
b Notes
• If the supplied remote interferes your other Sony
DVD recorder or player, change the command
mode number for this recorder (page 16).
• Use the batteries correctly to avoid possible
leakage and corrosion. Should leakage occur, do
not touch the liquid with bare hands. Observe the
following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an
extended period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid
inside the battery compartment, and insert new
batteries.
• Do not expose the remote sensor (marked on
the front panel) to strong light, such as direct
sunlight or a lighting apparatus . The recorder may
not respond to the remote.
• When you replace the batteries of the remote, the
code number and Command Mode may be reset
to the default setting. Set the appropriate code
number and Command Mode again.
Controlling TVs with the
remote
You can adjust the remote’s signal to control
your TV.
b Notes
• Depending on the connected unit, you may not be
able to control your TV with some or all of the
buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
Number
buttons
TV/DVD
TV 2 +/–
TV PROG
+/–
TV [/1
TV t
1 Hold down the TV [/1 button located
at the bottom of the remote.
Do not press the [/1 button at the top of
the remote.
Hookups and Settings
,continued
15
2 With the TV [/1 button pressed down,
enter the TV’s manufacturer code
using the number buttons.
For instance, to enter “09,” press “0” then
“9.” After you enter the last number,
release the TV [/1 button.
Code numbers of controllable TVs
If more than one code number is listed,
try entering them one at a time until you
find the one that works with your TV.
ManufacturerCode number
Sony01 (default)
Hitachi24
JVC33
Panasonic17, 49
Philips06, 08
Samsung71
Sanyo25
Thomson43
Toshiba38
The remote performs the following:
ButtonsOperations
TV [/1Turns your TV on or
TV 2 (volume)
+/–
TV PROG +/–Selects the
TV tSwitches your TV’s
off
Adjusts the volume
of your TV
programme position
on your TV
input source
If you have a Sony DVD player
or more than one Sony DVD
recorder
If the supplied remote interferes with your
other Sony DVD recorder or player, set the
command mode number for this recorder and
the supplied remote to one that differs from
the other Sony DVD recorder or player after
you have completed “Step 6: Easy Setup.”
The default command mode setting for this
recorder and the supplied remote is DVD3.
Number
buttons
SYSTEM
MENU
M/m,
ENTER
1 Check that “Easy Setup” (page 18)
has been finished. If “Easy Setup” has
not been finished, first perform “Easy
Setup.”
2 Press SYSTEM MENU.
The System Menu appears.
3 Select “SETUP,” and press ENTER.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between the
recorder and the last input source selected on
the TV. Point your remote at the recorder
when using this button.
When you connect the recorder to the TV via
the SCART jacks, the input source for the TV
is set to the recorder automatically when you
start playback. To watch another source,
press the TV/DVD button to switch the TV’s
input source.
16
4 Select “Others,” and press ENTER.
5 Select “Command Mode,” and press
ENTER.
6 Select a Command Mode (DVD1,
DVD2, or DVD3), and press ENTER.
7 Set the Command Mode for the remote
so it matches the Command Mode for
the recorder you set above.
Follow the steps below to set the
Command Mode on the remote.
1 Hold down ENTER.
2 While holding down ENTER, enter
the Command Mode code number
using the number buttons.
Command Mode Code number
DVD1number button 1
DVD2number button 2
DVD3number button 3
3 Hold down both the number and
ENTER buttons at the same time for
more than three seconds.
If the Command Mode for the recorder has
not been changed, set the Command Mode
for the remote to the default setting of
DVD3. If the Command Mode for the
remote is changed to DVD1 or DVD2, you
will be unable to operate this recorder.
Changing programme positions
of the recorder using the
remote
You can change programme positions of the
recorder using the number buttons.
Number
buttons,
SET
Example: for channel 50
Press “5,” “0,” then press SET.
Hookups and Settings
To check the Command Mode for the
recorder
Press x on the recorder when the recorder is
turned off. The Command Mode for the
recorder appears in the front panel display.
17
Step 6: Easy Setup
Make the basic adjustments by following the
on-screen instructions in “Easy Setup.”
[/1
</M/m/,,
O
RETURN
ENTER
TV [/1
1 Turn on the recorder and your TV.
Then switch the input selector on your
TV so that the signal from the recorder
appears on your TV screen.
The initial settings message appears.
• If this message does not appear, select
“Easy Setup” from “SETUP” in the
System Menu (“Settings and
Adjustments” on page 57).
2 Press ENTER.
Follow the on-screen instructions to
make the following settings.
Easy Setup - OSD
Select a language for the on-screen
displays.
Easy Setup - Tuner System
Select your country/region or language.
The programme position order will be set
according to the country/region you set.
To set the programme positions
manually, see page 57.
• If you live in a French speaking country
that is not listed on the display, select
“ELSE - English.”
Easy Setup - Clock
The recorder will automatically search
for a clock signal. If a clock signal cannot
be found, set the clock manually using
</M/m/,, and press ENTER.
Easy Setup - TV Type (page 61)
If you have a wide-screen TV, select
“16:9.” If you have a standard TV, select
either “4:3 Letter Box” (shrink to fit) or
“4:3 Pan Scan” (stretch to fit). This will
determine how “wide-screen” images are
displayed on your TV.
Easy Setup - Component Out
If you are using the COMPONENT
VIDEO OUT jack, select “On.”
Easy Setup - Line3 Input
If you plan to connect a decoder such as
a PAY-TV/Canal Plus analogue decoder
to the LINE 3/DECODER jack, select
“Yes.”
Easy Setup - Line1 Output
To output video signals, select “Video.”
To output S video signals, select “S
Video.”
To output RGB signals, select “RGB.”
Select “Video” to enjoy the
SMARTLINK features.
• If you set “Easy Setup - Component
Out” to “On,” you cannot select
“RGB.”
• If you set “Easy Setup - Line3 Input” to
“Yes,” you cannot select “S Video.”
Easy Setup - Audio Connection
If you connected an AV amplifier
(receiver) using a coaxial cord, select
“Yes : DIGITAL OUT” and set the
digital output signal (page 64).
3 Press ENTER when “Finish” appears.
“Easy Setup” is finished.
To return to the previous step
Press O RETURN.
z Hints
• If your AV amplifier (receiver) has an MPEG
audio decoder, set “MPEG” to “MPEG”
(page 64).
• If you want to run “Easy Setup” again, select
“Easy Setup” from “SETUP” in the System Menu
(page 70).
18
Connecting a VCR or Similar Device
After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar
recording device to the LINE IN jacks of this recorder.
For details, refer to the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording from connected equipment without a timer” on
page 45.
Connecting to the LINE 3/DECODER jack
Connect a VCR or similar recording device to the LINE 3/DECODER jack of this recorder.
TV
VCR
SCART cord (not supplied)
to SCART input
Hookups and Settings
to i LINE 1 – TV
to i LINE 3/DECODER
DVD recorder
b Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals through a VCR, you may not receive a clear image on your TV screen.
VCRDVD recorderTV
Be sure to connect your VCR to the DVD recorder and to your TV in the order shown below. To watch
video tapes, watch the tapes through a second line input on your TV.
Line input 1
VCRTV
• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3/
DECODER jack.
• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the
TV/DVD button on the remote.
• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected
VCR.
DVD recorder
Line input 2
,continued
19
Connecting to the LINE 2 IN jacks on the front panel
Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the
equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
S VIDEO
OUTPUT
VIDEO
AUDI O
LR
S-video cord
(not supplied)
to LINE 2 IN
: Signal flow
Audio/video cord
(not supplied)
DVD recorder
z Hint
When the connected equipment outputs only monaural sound, connect to just the L(MONO) and VIDEO
input jacks on the front of the recorder. Do not connect the R input jack.
b Notes
• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
• Do not connect the output jack of this recorder to another equipment’s input jack with the other
equipment’s output jack connected to the input jack of this recorder. This may cause noise (feedback).
• Do not connect more than one type of video cord between the recorder and your TV at the same time.
20
Connecting to a Satellite or Digital Tuner
Connect a satellite or digital tuner to this recorder using the LINE 3/DECODER jack.
Disconnect the recorder’s mains lead from the mains when connecting the tuner.
To use the Synchro-Rec function, see below. Do NOT set “Line3 Input” of the “Scart Setting”
to “Decoder” in the “Video” setup when making this connection.
TV
to SCART input
Satellite tuner,
CanalSat, etc.
SCART cord
(not supplied)
to i LINE 1 – TVto i LINE 3/DECODER
Hookups and Settings
If the satellite tuner can output RGB
signals
RGB signal images can be displayed on the
TV screen, but cannot be recorded. If the
satellite tuner can output RGB signals,
connect the TV SCART connector on the
satellite tuner to the LINE 3/DECODER jack,
and set “Line3 Input” of “Scart Setting” to
“Video/RGB” in the “Video” setup
(page 62). Note that this connection and
setup disable the SMARTLINK function. If
you want to use the SMARTLINK function
with a compatible set top box, see the
instructions supplied with the set top box.
DVD recorder
If you want to use the Synchro Rec
function
This connection is necessary to use the
Synchro-Recording function. See
“Recording from connected equipment with a
timer (Synchro Rec)” on page 44.
Set “Line3 Input” of “Scart Setting” in the
“Video” setup (page 62) according to the
specifications of your satellite tuner. See your
satellite tuner’s instructions for more
information.
If you are using a B Sky B tuner, be sure to
connect the tuner’s VCR SCART jack to the
LINE 3/DECODER jack. Then set “Line3
Input” of “Scart Setting” according to the
specifications of the VCR SCART jack on
your satellite tuner.
,continued
21
b Notes
• Synchro-Recording does not work with some
tuners. For details, see the tuner’s operating
instructions.
• If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected tuner.
22
Connecting a PAY-TV/Canal Plus Analogue Decoder
You can watch or record PAY-TV/Canal Plus analogue decoder programmes if you connect a
decoder (not supplied) to the recorder. Disconnect the recorder’s mains lead from the mains
when connecting the decoder. Note that when you set “Line3 Input” to “Decoder” in step 5 of
“Setting PAY-TV/Canal Plus analogue programme positions” (page 24), you will not be able
to select “L3” because Line 3 will become a dedicated line for the decoder.
Connecting a decoder
Hookups and Settings
to AERIAL
OUT
Aerial cable
(supplied)
to i LINE 1 – TV
to AERIAL IN
to SCART input
SCART cord
(not supplied)
TV
PAY-TV/Canal Plus
analogue decoder
SCART cord (not supplied)
to i LINE 3/DECODER
DVD recorder
,continued
23
Setting PAY-TV/Canal Plus
analogue programme positions
To watch or record PAY-TV/Canal Plus
analogue programmes, set your recorder to
receive the programme positions using the
on-screen display.
In order to set the programme positions
correctly, be sure to follow all of the steps
below.
Number
buttons
SYSTEM
MENU
</M/m/,,
O
RETURN
ENTER
1 Press SYSTEM MENU.
The System Menu appears.
2 Select “SETUP,” and press ENTER.
4 Select “Scart Setting,” and press
ENTER.
5 Press M/m to select “Video” or “RGB”
for “Line1 Output,” “Decoder” for
“Line3 Input,” and “Video” for “Line3
Output,” and press ENTER.
The “Video” setup display appears again.
6 Press O RETURN to return the cursor
to the left column.
7 Select “Basic,” and press ENTER.
8 Select “Channel Setting,” and press
ENTER.
3 Select “Video,” and press ENTER.
24
9 Press M/m to select the desired
programme position, and press
ENTER.
10
Select “System” using </,.
11
Press M/m to select an available TV
system, BG, DK or I.
12
Select “Channel” using </,.
13
Select the PAY-TV/Canal Plus
analogue programme position using
M/m or number buttons.
14
Select “PAY-TV/ CANAL+” using </
,.
Hookups and Settings
15
Select “On” using M/m, and press
ENTER.
To return to the previous step
Press O RETURN.
b Note
If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected decoder.
25
Eight Basic Operations
— Getting to Know Your DVD Recorder
1. Inserting a Disc
+
RW
-
R
Video
Z (open/
close)
-
RWVR-RW
DVD
VCDCD
Video
+
-
R
DATA CD
RVR
2. Recording a
Programme
+
RW+R
This section introduces the basic operation to
record a current TV programme to a disc
(DVD). For an explanation of how to make
timer recordings, see page 36.
PROG +/–
TV/DVD
1 Press Z (open/close), and place a
disc on the disc tray.
Recording/playing side facing down
2 Press Z (open/close) to close the disc
tray.
Wait until “LOAD” disappears from the
front panel display.
Unused DVDs are formatted
automatically.
If the disc is recordable on this recorder,
you can manually re-format the disc to
make a blank disc (page 35).
DISPLAY
z REC
x REC
STOP
REC MODE
TV t
1 Insert a recordable DVD.
2 Press PROG +/– to select the
programme position or input source
you want to record.
3 Press REC MODE repeatedly to select
the recording mode.
Each time you press the button, the
display on the TV screen changes as
follows:
For more details about the recording
mode, see page 36.
4 Press z REC.
Recording starts.
Recording stops automatically after 8
hours of continuous recording or when
the DVD is full.
26
To stop recording
Press x REC STOP.
Note that it may take a few seconds for
recorder to stop recording.
To watch another TV programme while
recording
If your TV is connected to the i LINE 1 –
TV jack, set your TV to the TV input using
the TV/DVD button and select the
programme you want to watch. If your TV is
connected to the LINE 2 OUT or
COMPONENT VIDEO OUT jacks, set the
TV to TV input using the TV t button
(page 15).
b Notes
• After pressing z REC, it may take a short while
to start recording.
• You cannot change the recording mode while
recording.
• If there is a power failure, the programme you are
recording may be erased.
• You cannot watch a PAY-TV/Canal Plus
programme while recording another PAY-TV/
Canal Plus programme.
• To use the TV Direct Rec function, you must first
correctly set the recorder’s clock.
Checking the disc status while
recording
Eight Basic Operations — Getting to Know Your DVD Recorder
TV Direct Rec
If you are using the SMARTLINK
connection, you can easily record what you
are watching on your TV.
When the TV is turned on, press z REC. The
recorder automatically turns on and starts
recording what you are watching on the TV.
b Note
If “TV” appears in the front panel display, you
cannot turn off the TV or change the programme
position during TV Direct Rec. To turn off the
function, set “TV Direct Rec” to “Off” in the
“Recording” setup (page 66).
About the Teletext function
Some broadcast systems ensure a Teletext
service* in which the complete programmes
and their data (title, date, programme
position, recording start time etc.) are stored
day by day. When recording a programme,
the recorder automatically takes the
programme name from the Teletext pages
and stores it as the title name. For details, see
“Auto Programme Title Labelling (TV Guide
Page)” on page 59.
Note that the Teletext information will not
appear on your TV screen. To view the
Teletext information on your TV screen,
press TV/DVD on the remote to switch the
input source to your TV (page 15).
* not available in some areas
You can check the recording information
such as recording time or disc type.
Press DISPLAY during recording.
The recording information appears.
A Disc type/format
B Recording status
C Recording mode
D Recording time
Press DISPLAY to turn off the display.
27
Loading...
+ 61 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.