Sony NSX-GT1 Reference Guide

Internet TV

Reference Guide

NSX-24GT1/NSX-32GT1/NSX-40GT1/NSX-46GT1

Owner's Record

The model and serial numbers are located
on the side and rear of the TV. For
NSX-GT1 series mo dels, they can be found
by removing the cable cov er. Record these
numbers in the spaces provided below.
Refer to them whenever you call upon your
Sony dealer regarding this TV.

Model No.______________

Serial No.______________

Location of the identification
label

Labels for Model No. and Power Supply
rating (in accordance with applicable
safety regulation) are located on the rear of
the TV. For NSX-GT1 series models, they
can be found by removing the cable cover.

WARNING

To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.

Batteries or batteries installed apparatus
shall not be exposed to excessive heat
such as sunshine, fire or the like.

The TV must never be exp osed to dripping,
splashing, or spilling liquids of any kind.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE,

NE PAS OUVRIR

PRECAUCION

RIESGO DE CHOQUE ELECTRICO

NO ABRIR

This symbol is intend ed to alert
the user to the presence of
uninsulated “dangerous
voltage” within the TV’s

sufficient magnitude to constitute a risk of
electric shock to persons.

accompanying the TV.

enclosure that may be of

This symbol is intend ed to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature

Outdoor Antenna Grounding

Antenna lead-in
wire

Ground clamps

Electrical service
equipment

NEC: National Electrical
Code

Antenna discharge
unit (NEC Section
810-20)

Grounding
conductors (NEC
Section 810-21)

Ground clamps

Power service grounding
electrode system
(NEC Art 250 Part H)

CAUTION

To prevent electric shock and blade
exposure, do not use this polarized AC
plug with an extension cord, receptacle or
other outlet unless the blades can be fully
inserted.

• Operate the TV only on 120 V AC

• Avoid operating the TV at temperatures
below 41°F (5°C).

Declaration of Conformity

Trade Name: SONY
Model: NSX-24GT1/NSX-32GT1/
NSX-40GT1/NSX-46GT1
Responsible Party: Sony Electronics
Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230

This device complies with part 15 of the
FCC rules. Operation is subject to the
following two cond itions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.

FCC Related Information

This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not o ccur in
a particular installation. If this equipment
does cause harmful i nterference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the
receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

Pursuant to FCC regulations, you are
cautioned that any changes or
modifications not expr essly approved in
this manual could void your authority to
operate this equipment.

Safety and Regulatory

To prevent radio interference to the
licensed service, this device is intended to
be operated indoors and away from
windows to provide maximum shielding.
Equipment (or its transmit antenna) that is
installed outdoors is subject to licensing.
Only use Wireless LAN indoors when using
it with IEEE 802.11a/n (5 GHz).
High power radars are allocated as
primary users (meaning they have priority)
of 5250-5350 MHz and
5650-5850 MHz and these radars could
cause interference and/or damage to this
device.
This device uses 5 GHz band for wireless
LAN communication and the maximum
gain of the antenna in this device is 6 dBi.
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with
minimum distance 20 cm between the
radiator and your body (excluding
extremities: hands, wrists and feet).
This device and its antenna(s) must not be
co-located or operating with any other
antenna or transmitter except Grant
condition.

2

Note

This television includes a QAM
demodulator which should allow you to
receive unscrambled digital cable
television programming via subscription
service to a cable service provider.
Availability of digital cable television
programming in your area depends on the
type of programming and signal provided
by your cable service provider.

Compatible Wall-Mount
Bracket Information

Use the following Sony Wall-Mount Bracket
with your TV model.

Sony Model No.

NSX- 24GT1 32GT1/40GT1/46GT1

Sony
Wall-Mount
Bracket Model
No.

Use with other Wall-Mount Brackets* may
cause instability and could result in
property damages or injury.

* For instructions on using the Wall-Mount

bracket with your TV please go to http://
esupport.sony.com for your TV model
and download "Additional Information
for Using Sony Wall-Mount Bracket".

SU­WL100

SU-WL500

To Customers

Sufficient expertise is required for TV
installations. Be sure to subcontract the
installation to a Sony dealer or licensed
contractor and pay adequate attention to
safety during the installation.

Notice regarding disposal
(For NSX-24GT1 only)

Lamp in this product contains mercury.
Disposal of these materials may be
regulated due to environmental
considerations. For disposal or recycling
information, please contact your local
authorities or the Telecommunications
Industry Association(www.eiae.org).

Important Safety
Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near

water.

6) Clean only with dry cloth.

7) Do not block any ventilation

openings. Install in accordance with
the manufacturer’s instructions.

8) Do not install near any heat sources

such as radiators, heat registers,
stoves, or other apparatus (inc luding
amplifiers) that produce heat.

9) Do not defeat the safety purpose of

the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the other.
A grounding type plug has two
blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the
provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.

10)Protect the power cord from being

walked on or pinched particularly at
plugs, convenience receptacles,
and the point where they exit from
the apparatus.

11)Only use attachments/accessories

specified by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.

14)Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such as
power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.

13)Unplug this apparatus during
lightning storms or when unused for
long periods of time.

3

Additional Safety
DOs and DON’Ts

MOISTURE

• Do not place liquid filled objects such
as a vase or potted plant on the TV.

• Do not use a power line operated TV
set near water; for example, near a
bathtub, washbowl, kitchen sink,
laundry tub, wet basement or near a
swimming pool, etc.

• Never place the TV on a bed, sofa, rug
or other similar surface where
ventilation openings may be blocked.

• Unless proper ventilation is provided,
the TV may accumulate dust and
cause damage.

• Never allow liquid or
solid objects to fall into
the ventilation openings.

deformation of the enclosure and/or
TV malfunction.

• Do not install the TV in a place
exposed to direct air conditioning;
moisture may condense inside and
may cause TV malfunction.

CLEANING

When cleaning, be sure to unplug the
power cord to avoid any chance of
electric shock.

• Clean the cabinet of the TV with a dry
soft cloth.

• Wipe the LCD screen gently with a soft
cloth.

• Stubborn stains may be removed with
a cloth slightly moistened with a
solution of mild soap and warm water.

• Do not spray water or detergent
directly on the TV set. It may drip to the
bottom of the screen or exterior parts,
and may cause a malfunction.

• If using a chemically pretreated cloth,
please follow the instruction provided
on the package.

• Never use strong solvents such as a
thinner, alcohol or benzine for
cleaning.

• Periodic vacuuming of the ventilation
openings is recommended to ensure
to proper ventilation.

VENTILATION

The ventilation openings in the TV are
necessary to ensure reliable operation
of the TV and to protect it from
overheating.

• Do not block or cover
the ventilation
openings with cloth or
other materials.

• If any liquid or solid object falls inside
the TV, unplug the TV immediately and
have it checked by qualified service
personnel before operating it further.

• Never push objects of any kind into
the TV through the ventilation
openings as they may come in contact
with dangerous voltage points or short
out parts that could result in a fire or an
electric shock.

Allow adequate space around the TV
set to ensure proper air circulation.

• Never place the TV in a confined
space, such as a bookcase or built-in
cabinet, unless proper ventilation is
provided.

• There should be a clearance of at
least 11 7/8 inches (30 cm) above the
TV set and 4 inches (10 cm) on each
side. If mounted on the wall, allow at
least 4 inches (10 cm) of clearance at
the bottom of the screen (see page 8).

INSTALLATION

The TV should be installed near an
easily accessible AC power outlet.

• Do not install the TV face up or down,
upside down or on its side.

• Do not install the TV in hot, oily, humid,
or excessively dusty places.

• Do not install the TV in places subject
to extreme temperature, such as in
direct sunlight, near a radiator or a
heating vent. The TV may overheat in
such conditions which can cause

• Do not install the TV where it may be
exposed to mechanical vibration.

• Do not install the TV where insects
may enter.

• Do not install the TV in a location
where it may protrude, such as on or
behind a pillar, or any place you might
bump your head or receive bodily
injury.

• To prevent fire keep flammable
objects or open flame (e.g. candles)
away from the TV.

• Do not place optional equipment on
top of the TV.

Prevent the TV from toppling
over

Take measures to prevent
the TV from toppling over
and causing injury or
damage to the TV and
property.

• Secure the TV to a wall and/or stand.

• Never install the TV on unstable and/or
uneven surfaces.

• Do not allow children to climb on or
play with furniture and TV sets.

• Do not install the TV on furniture that
can easily be used as steps, such as
a chest of drawers.

• Care should be taken to install the TV
where it cannot be pushed, pulled
over, or knocked down.

• Care should be taken to route all AC
power cords and connecting cables
so that they cannot be pulled or
grabbed by curious children.

4

Medical institutions

Do not place this TV in a place where
medical equipment is in use. It may
cause a medical equipment
malfunction.

Outdoor use

Do not install this TV outdoors. The TV
should not be exposed to rain or direct
sunlight in order to avoid damage and
possible fire or electric shock.

Do not install this TV in a
vehicle, ship or other vessel

• Excessive bumping motion of a
moving vehicle or continuous swaying
motion on a boat may cause the TV to
fall down and cause injury.

• Exposing the TV to seawater may
cause a fire, electric shock or damage
to your TV.

Magnetic influence

• This TV contains a strong magnet in
the speaker unit that generates a
magnetic field. Keep any items
susceptible to magnetic fields away
from the speaker.

• Electro-magnetic radiation emitted
from optional equipment installed too
close to the TV may cause picture
distortion and/or noisy sound.

Wall-mount use

• Wall-mount installation requires the
use of a Wall-Mount Bracket. When
installing or removing the TV and the
Wall-Mount Bracket, be sure to use
qualified contractors. If not properly
secured during installation or removal
from the Wall-Mount Bracket, the TV
may fall and cause serious injury.

• Be sure to follow the installation guide
supplied with the Wall-Mount Bracket
when installing the TV.

• Be sure to attach the brackets with the
specified parts supplied with the
Wall-Mount Bracket.

• Do not hang the TV from the ceiling. It
may fall and cause serious injury.

• Do not hang anything on the TV.

• Do not allow children to climb on the
TV.

AC POWER CORD

• Do not touch the AC
power cord and its
plug with wet hands
as it may cause
electric shock.

• When disconnecting
the AC power cord,
grasp the plug and
disconnect from the wall
outlet first. Do not pull by
the cord.

• Keep the power cord away from heat
sources.

A TV set with a three-wire grounding
type AC power cord plug must be
connected to an AC power outlet with a
protective earthing connection.

• Do not convert or damage the AC
power cord.

• Consult your electrician to have the
outlet changed to suit your TV.

Subjecting the AC power cord to wear
and/or abuse can damage the AC
power cord and your TV.

• Do not place the TV where the power
cord can be easily pinched, bent,
twisted, or catch your feet.

• Do not allow anything to rest on or roll
over the cord.

• Before connecting cables, be sure to
unplug the AC power cord for your
safety.

• Do not move the TV with the AC power
cord (or other cables such as audio
and video) connected.

• Use only an original Sony AC power
cord with your TV; no brand
substitution is allowed (except
NSX-24GT1).

• Do not use AC power cord supplied
with the TV with any other equipment.

• Never use a damaged
AC power cord. A
damaged AC power
cord can cause a
short-circuit, which may
result in a fire or electric
shock.

Do not use a damaged or
poorly fitting AC power
outlet as your TV’s power
source.

• Insert the plug fully into
the outlet. If it is loose, it
may cause arcing and
result in a fire.

• Do not overload the
same AC power outlet.

Unplugging the AC power cord from the
wall outlet will completely remove power
from the TV.

• During lightning storms or when the
TV is left unattended and unused for
extended periods of time, the AC
power cord should be unplugged
from the wall outlet. This will avoid
possible damage to your TV. Also
unplug the antenna to prevent
damage to the TV.

• For energy conservation and safety
reasons, practice unplugging the AC
power cord from the AC power outlet.

Clean the AC power plug

Unplug the AC
power plug and
clean it
occasionally to
avoid dust from accumulating. While
cleaning, look for signs of damage. A
damaged AC power cord should never
be used.

ACCESSORIES

Keep small accessories out of
children’s reach. Use only the specified
accessories with this TV.

5

Volume Adjustment

• When using
headphones, adjust the
volume to avoid
excessive audio levels
from causing possible
hearing loss.

BATTERIES

Your remote control batteries are
consumables.

• To preserve our environment, dispose
of used batteries according to your
local laws or regulations.

• Do not dispose of batteries in a fire.

• Do not short-circuit, disassemble or
overheat the batteries.

• Replace only with the same or
equivalent type of batteries. Using
incorrect replacement batteries can
lead to an explosion.

• Do not place the remote in a location
near a heat source, a place subject to
direct sunlight, or a damp room.

LCD SCREEN

• Although the LCD screen is made with
high-precision technology and has
effective pixels of 99.99% or more,
black dots or bright points of light
(red, blue, or green) may appear
constantly on the LCD screen. This is
a structural property of the LCD panel
and is not a malfunction.

• The LCD screen is made with
high-precision technology and to
achieve a high level of performance
and picture quality, this TV’s backlight
setting is set to maximize the
brightness of the TV. However,
uneven brightness may be observed
when the LCD TV is viewed in a dark
ambient without an input source or
with a blank screen. This condition is
normal and not a malfunction of the
TV. Changing the Picture mode,
Backlight setting, enabling the Light
Sensor (if applicable), or turning on
the Power Management will improve
this condition.

• To avoid damaging the LCD panel, do
not expose the LCD screen to direct
sunlight.

• Do not push or scratch the LCD
screen, or place objects on top of the
TV. The images may be uneven or the
LCD panel may be damaged.

• If the TV is used in a cold place, the
picture may smear or become dark.
This does not indicate a failure. These
phenomena improve as the
temperature rises.

• Ghosting may occur when still
pictures are displayed continuously. It
should disappear after a few
moments.

• The LCD screen and enclosure get
warm when the TV is in use. This is not
a malfunction.

• Avoid spraying insect repellent with
volatile material on the LCD screen.

• Avoid prolonged contact with rubber
or plastic material to the LCD screen.

Broken screen panel

Do not throw anything at the TV as the
impact can cause the LCD screen glass
to crack, break or scatter.

• If damage occurs to the LCD panel,
small traces of liquid crystal
sandwiched between the glass may
be found on scattered broken glass.

• Do not touch the broken glass with
bare hands. As with any broken glass
pieces, avoid skin contact and
exposure to your eyes or mouth. Avoid
direct contact with liquid or damp
surfaces of the glass as these may
have an adverse effect on some
people. The contacted area should be
rinsed thoroughly with water. If
conditions persist, see your doctor.

• If the surface of the TV cracks, do not
touch the TV until you have unplugged
the AC power cord. Otherwise electric
shock may result.

SERVICING

Do not use the TV if you
suspect the TV is
damaged or if the TV is
damaged.

• Do not attempt to
service the TV
yourself since
opening the
cabinet may
expose you to
dangerous voltage levels or other
hazards. Refer all servicing to
qualified service personnel.

• If replacement parts
are required, acquire
a written certification
from the service
technician which
states that adequate
replacement parts with the same or
similar characteristics as the original
parts have been used. Unauthorized

substitutions may result in a fire, an
electric shock or other hazards.

Safety check

• Upon completion of any TV servicing
or repair, ask the service technician to
perform routine safety checks as
specified by Sony and to certify that
the TV is safe to operate. Have a
qualified service technician dispose of
the TV if it is not safe to operate.

6

Attaching the
Table-Top Stand

Refer to the supplied Table-Top
Stand leaflet for proper
attachment.

1 Gently slide the TV onto the

Table-Top Stand and align the
screw holes.

NSX-24GT1

NSX-32GT1

2 Use the supplied screws to

attach the TV to the Table-Top
Stand.

NSX-24GT1

NSX-32GT1

NSX-40GT1/NSX-46GT1

Detaching the
Table-Top Stand
from the TV

Remove only the screws marked
with on the TV.

NSX-24GT1

NSX-32GT1

NSX-40GT1/NSX-46GT1

• Do not put stress on the LCD panel
or the frame around the screen.

• Be careful to not pinch your hands
or the AC power cord when you
install the TV to the Table-Top
Stand.

• If you use an electric screwdriver,
set the tightening torque at
approximately 1.5 N·m {15 kgf·cm}.

3 After all the screws are

tightened, cover the Table-Top
Stand with the supplied Cable
cover.

NSX-40GT1/NSX-46GT1

• Remove the Cable cover prior to
detaching the Table-Top Stand.

• Do not remove the Table-Top Stand
for any reason other than to install
corresponding accessories on the TV.

• When installing the TV on a wall,
remove the screws from the rear of the
TV. (They are fastened in the screw
holes for wall mounting.) Be sure to
store the removed screws in a safe
place, keeping them away from
children.

7

• When attaching the Table-Top Stand
again, be sure to fasten the screws
(previously removed) to the original
holes on the rear of the TV.

Using a Wall-Mount
Bracket

Your TV can be mounted on a wall
using a Wall-Mount Bracket (not
supplied) out of the box as
packaged. If the Table-Top Stand
is attached to the TV, the TV may
require detaching the Table-Top
Stand; see “Detaching the
Table-Top Stand from the TV”
(page 7).
Prepare the TV for the Wall-Mount
Bracket before making cable
connections.

For product protection and safety
reasons, Sony strongly
recommends that you use the
Wall-Mount Bracket designed for
your TV and the installation should
be performed by a Sony dealer or
licensed contractor.

• Follow the operating instructions
supplied with the Wall-Mount
Bracket for your model. Sufficient
expertise is required in installing
this TV, especially to determine the
strength of the wall for withstanding
the TV’s weight.

• Be sure to use the screws supplied
with the Wall-mount bracket when
attaching the mounting hooks to the
TV set.
The supplied screws are designed
so that they are 8 mm to 12 mm in
length when measured from the
attaching surface of the mounting
hook.
The diameter and length of the
screws differ depending on the
Wall-mount bracket model. Use of
screws other than those supplied
may result in internal damage to the
TV set or cause it to fall, etc.

8-12 mm

Screw
(supplied with the
Wall-mount bracket)

Mounting Hook

Hook attachment on
rear of TV set

• Be sure to store the unused screws
and Table-Top Stand in a safe
place until you are ready to attach
the Table-Top Stand. Keep the
screws away from small children.

• Read page 2 to 6 for additional safety
information.

Installing the TV
Against a Wall or
Enclosed Area

Make sure that your TV has
adequate ventilation. Allow
enough space around the TV as
shown below. Avoid operating the
TV at temperatures below 41 °F
(5 °C).

Installed with stand

Leave at least this much space around the set.

Installed on the wall

Leave at least
this much space
around the set.

Never install the TV set as follows:

Air circulation is blocked. Air circulatio n is blocked.

• Inadequate ventilation can lead to
overheating of the TV and may cause
damage to your TV or cause a fire.

Pairing the keypad
with the TV

1 Make sure that the batteries

are correctly inserted.

2 Press the CONNECT button on

the TV for two seconds or more
to display the pairing screen.

3 Hold down the Fn and Enter

keys following the instructions
on the screen until the pairing
screen disappears.

How to Care for
Your TV

Safety is very important, please
read and follow the safety
documentation (page 2 to 6).

Unplug the TV and other
connected equipment from the
wall outlet before you begin
cleaning your TV.

• Wipe the LCD screen gently with a soft
cloth.

• Stubborn stains may be removed with
a cloth slightly moistened with a
solution of mild soap and warm water.

• If using a chemically pretreated cloth,
please follow the instruction provided
on the package.

• Never use strong solvents such as a
thinner, alcohol or benzine for
cleaning.

• Do not plug in the TV into the wall
outlet until the moisture from cleaning
has evaporated.

The TV should also be placed on a
stable surface to prevent it from
toppling over (see page 4). If you
have young children or pets at
home, check regularly to insure the
TV is securely fastened.

8

Specifications

Model Name NSX- 46GT1 40GT1 32GT1 24GT1

System

Television system NTSC: American TV standard

Channel coverage Analog terrestrial: 2-69 / Digital terrestrial: 2-69

Panel system LCD (Liquid Crystal Display) Panel

Speaker output 10W + 10W 5W + 5W

Input/Output jacks

CABLE/ANTENNA 75-ohm external terminal for RF inputs

VIDEO IN VIDEO / AUDIO

COMPONENT IN YPBPR (Component Video)/Signal format: 480i, 480p, 720p, 1080i, 1080p

HDMI IN 1/2/3/4 HDMI: Video:480i, 480p, 720p, 1080i, 1080p, 1080/24p

HEADPHONE Headphones jack

DIGITAL AUDIO OUT (OPTICAL) PCM/Dolby Digital optical signal

LAN 10BASE-T/100BASE-TX/1000BASE-T connector (Connection speed may differ depending on the

USB USB jack Type A*

IR Blaster Mini jack (For connecting the IR Blaster cable)

Power and others

Power requirements 120 V AC, 60 Hz

Power consumption

in use 147 W 122 W 85 W 84 W

2

in DAM*

in standby less than 0.5 W

Screen size
(inches measured diagonally)

Display resolution 1,920 dots (horizontal) x 1,080 (vertical)

Speaker

Full range with speaker (mm) 45 × 130 45 × 130 45 × 130 34 × 105

(inches) 1

Dimensions

with stand (mm) 1,087 × 694 × 298 954 × 619 × 298 766 × 511 × 194 571 × 381 × 190

(inches) 42

without stand (mm) 1,087 × 661 × 54 954 × 586 × 53 766 × 481 × 56 571 × 353 × 71

(inches) 42

wall-mount hole pattern
(mm)

wall-mount screw size
(mm)

Mass

with stand (kg)/(lb.) 22.7/50.1 18.8/41.5 13.2/29.2 10.1/22.3

without stand (kg)/(lb.) 21/46.4 17.1/37.7 11.8/26.1 8.7/19.2

ATSC (8VSB terrestrial): ATSC compliant 8VSB
QAM on cable: ANSI/SCTE 07 2000 (Does not include Cable CARD functionality)

Analog Cable: 1-135 / Digital Cable: 1-135

AUDIO

Audio: Two channel linear PCM 32, 44.1 and 48KHz, 16, 20 and 24bits, Dolby Digital

network environment. 10BASE-T/100BASE-TX/1000BASE-Tconnection rate and communication
quality are not guaranteed for this TV.)

56 Wh/d 34 Wh/d 27 Wh/d

46 inches 40 inches 31.5 inches (32 class) 23.5 inches (24 class)

13

7

/8 × 27 3/8 × 11 3/4 37 5/8 × 24 3/8 × 11 3/4 30 1/4 × 20 1/8 × 7 3/4 22 1/2 × 15 × 7 1/2

7

/8 × 26 1/8 × 2 1/4 37 5/8 × 23 1/8 × 2 1/8 30 1/4 × 19 × 2 1/4 22 1/2 × 14 × 2 7/8

300 × 300 300 × 300 200 × 200 100 ×100

M6 × 16 M6 × 16 M6 × 16 M4 × 12

1

/16 × 5 1/8 1 13/16 × 5 1/8 1 13/16 × 5 1/8 1 3/8 × 4 1/4

9

Wireless

Wireless LAN standard IEEE 802.11a/b/g/n

Frequency range 2.4 GHz band: Channels 1-11

Modulation DS-SS Modem and OFDM Modem

5 GHz band: Channels 36-64, 100-140, 149-165

Accessories

Supplied accessories Keypad (1) / Size AA batteries (2) / AC power cord (except NSX-24GT1) (1) /

Optional accessories Connecting cables / Wall mount bracket

*1

For details on USB devices that can be connected to the TV, see "Help Guide" (http://esupport.sony.com/internettv/helpguide).

*2

Download Acquisition Mode (DAM) is used for collecting data for TV Guide On Screen.

IR Blaster cable (1) / Table-Top Stand (1) / Screws (M4 x 10, for NSX-GT24)(3), Screws (M5 x 16, for
NSX-32GT1/NSX-40GT1/NSX-46GT1)(3) / Cable cover (1) / Quick Setup Guide (1) / Reference Guide
(1) / Table-Top Stand leaflet (1) / Attention (1) / End User License Agreement (1) / Warranty card (1)

• Optional accessories availability depends on its stock.

• Design and specifications are subject to change without notice.

10

Additional
Information

About wireless LAN security

Since communication via the wireless
LAN function is established by radio
waves, the wireless signal may be
susceptible to interception. To
protect wireless communication, this
TV supports various security
functions. Be sure to correctly
configure the security settings in
accordance with your network
environment.

No Security

Although you can easily make
settings, anyone can intercept
wireless communication or intrude
into your wireless network, even
without any sophisticated tools. Keep
in mind that there is a risk of
unauthorized access or interception
of data.

WEP

WEP applies security to
communications to prevent outsiders
from intercepting communications or
intruding into your wireless network.
WEP is a legacy security technology
that enables older devices, which do
not support TKIP/AES, to be
connected.

WPA-PSK (TKIP), WPA2-PSK (TKIP)

TKIP is a security technology
developed to correct for the
deficiencies of WEP. TKIP assures a
higher security level than WEP.

WPA-PSK (AES), WPA2-PSK (AES)

AES is a security technology that
uses an advanced security method
that is distinct from WEP and TKIP.
AES assures a higher security level
than WEP or TKIP.

Trademark
Information

HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC in the United States and other
countries.

Fergason Patent Properties, LLC:
U.S. Patent No. 5,717,422
U.S. Patent No. 6,816,141

Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.

In the United States, TV Guide and TV
Guide On Screen are registered
trademarks of TV Guide Entertainment
Group, Inc. and/or its subsidiaries or
affiliates, and are used under a license by
Gemstar-TV Guide International, Inc. and/
or its subsidiaries. In Canada, TV Guide is
a registered mark of Transcontinental Inc.,
and is used under a lice nse by Gemstar-TV
Guide International, Inc. and/or its
subsidiaries.

The TV Guide On Screen system is
manufactured under license from
Gemstar-TV Guide International, Inc. and/
or its subsidiaries.

Gemstar-TV Guide International, Inc. and/
or its related affiliates are not in any way
liable for the accuracy or availability of the
program schedule information or other
data in the TV Guide On Screen system
and cannot guarantee service availability
in your area. In no event shall Gemstar-TV
Guide International, Inc. and/or its related
affiliates be liable for any damages in
connection with the accuracy or availability
of the program schedule information or
other data in the TV Guide On Screen
system.

Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.

This product contains software which is
licensed by Fluendo
(http://www.fluendo.com).

11

For Your Convenience

The Help Guide gives you detailed information on how to use the Internet TV
as follows:
– Basics of the Internet TV
– How to use applications
– Details on how to use the Keypad
– Customizing settings
– Software Updates

From your Internet TV

Select “Help Guide” from the Applications List.
Or, press (SEARCH) and type “help” in the Quick Search Box. Help Guide
appears in the search results.

• The network connection is required for accessing the "Help Guide" from the
TV.

From a PC browser

Access the following:
http://esupport.sony.com/internettv/helpguide/

© 2010 Sony Corporation

4-199-355-17(1)

Printed in U.S.A.