Sony kl w7000, kl 9000 schematic

HISTORY

When clicking an item, it’s detail is displayed.

Model Name: KL-W7000/W9000 SERVICE MANUAL Part No. : 9-965-180-01

Date SUP/COR No. Description of SUP/COR

1998.08 COR-1 PARTS CHANGE Yes PARTS CHANGE AND ADDITION OF ACCESORIES

1999.06 COR-2 PACKING MATERIALS

Change of

main text

Yes

SERVICE MANUAL

LJ-2T

CHASSIS

MODEL MODEL

RM-Y980

KL-W7000

RM-Y980USCanadian

KL-W7000

CHASSIS No. CHASSIS No.COMMANDER DEST. COMMANDER DEST.

SCC-N56B-A

KL-W9000

SCC-N56B-A

KL-W9000

RM-Y980

RM-Y980USCanadian

SCC-N56A-A

MICROFILM

Please file according to model size...

KL-W7000 KL-W9000RM-Y980

LCD PROJECTION DATA MONITOR

KL-W7000/W9000

RM-Y980

Specifications

Acceptable signal NTSC video signal, RGB signal

(For details, see page 9.)

Projection system 3 LCD panels, 1 lens projection

system

LCD panel 1.35-inch TFT LCD panel

Approx. 1.54 million dots (512,880 pixels)

1068.5 × 480 dots × 3 panels

Lamp XL-100U: HID lamp, 100 W Lens Large diameter hybrid lens F2.4 Screen size (measured diagonally)

KL-W7000: 37 inches (942 mm) KL-W9000: 50 inches (1,272 mm)

Viewable image size (for RGB input)

KL-W7000: Approx. 36.3 inches (921 mm) (diagonally) Approx. 803 × 452 mm (w/h) KL-W9000: Approx. 49.1 inches (1247 mm) (diagonally) Approx. 1087 × 611 mm (w/h)

Deflection frequency

Horizontal: 31.5–48 kHz Vertical: 50–85 Hz

Inputs/outputs

VIDEO 1, 2 and 3 IN

VIDEO OUT

S VIDEO (VIDEO 1, 3 IN only) (4-pin mini-DIN):

Y: 1 Vp-p, 75 ohms unbalanced, sync negative C: 0.286 Vp-p (burst signal), 75 ohms

VIDEO (phono jacks):

1 Vp-p, 75 ohms unbalanced, sync negative

AUDIO (phono jacks):

2 channels, 500 mVrms Impedance: more than 47 kohms

S VIDEO (4-pin mini-DIN):

Y: 1 Vp-p, 75 ohms unbalanced, sync negative C: 0.286 Vp-p (burst signal), 75 ohms

VIDEO (phono jacks):

1 Vp-p, 75 ohms unbalanced, sync negative

AUDIO (phono jacks):

2 channels, 500 mVrms Impedance: less than 5 kohms

RGB 1, 2 IN

VIDEO (D-sub 15-pin, female):

R, G, B: 0.7 Vp-p, positive, 75 ohms terminated Sync on Green: 0.286 Vp-p SYNC/HD: Composite sync: TTL, high impedance, sync positive/negative Horizontal sync: TTL, high impedance, sync positive/ negative VD: Vertical sync: TTL, high impedance, sync positive/

negative AUDIO (RGB 1 IN) (phono jacks)

2 channels, 500 mVrms

Impedance: more than 47

kohms AUDIO (RGB 2 IN) (stereo minijack)

500 mVrms

Impedance: more than 47

kohms

Power requirement

100 to 120 V AC, 50/60 Hz

Power consumption

190 W (MAX) Standby mode: 2 W

Dimensions KL-W7000: 920 x 825 x 390 mm

(36

× 32

× 15

/8 inches)

(w/h/d) KL-W9000: 1,228 × 1,055 × 565 mm (48

× 41

× 22

inches) (w/h/d)

Mass KL-W7000: Approx. 30 kg

(68 lbs 2 oz) KL-W9000: Approx. 43 kg (106 lbs 8 oz)

Supplied accessories

Remote control RM-Y980 (1) Size AA (R6) batteries (2) AC power cord (1) RGB signal cable (D-sub 15-pin

˜ D-sub 15-pin) (1) HD15-HD15 (male, without the

No. 9 pin) adaptor (1) Macintosh adaptor (1) Windows 95 Monitor

Information Disk (1) Brackets (2) Screws for brackets (2) Buckle (1) Hexagon head wrench (1) Dust remover (1)

Optional accessories

Lamp unit XL-100U

Design and specifications are subject to change without notice.

– 2 –

SAFETY CHECK-OUT

(US Model only)

KL-W7000/W9000

RM-Y980

After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.

7. Check the condition of the monopole antenna (if any). Make sure the end is not broken off, and has the plastic cap on it. Point out the danger of impalement on a broken antenna to the customer, and recommend the antenna’s replacement.

8. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV.

9. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below.

To Exposed Metal Parts on Set

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or

RCA WT-540A. Follow the manufacturers’ instructions to

use these instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-

tion is 0.75 V, so analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-

amples of a passive VOMs that are suitable. Nearly all battery

operated digital multimeters that have a 2 V AC range are suit-

able. (See Fig. A)

HOW TO FIND A GOOD EARTH GROUND

A cold-water pipe is guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also at earth ground. If the retaining screw is to be used as your earth-ground, verify that it is at ground by measuring the resistance between it and a coldwater pipe with an ohmmeter. The reading should be zero ohms. If a cold-water pipe is not accessible, connect a 60 – 100 watts trouble light (not a neon lamp) between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side of the line, the lamp should light at normal brilliance if the screw is at ground potential. (See Fig. B)

0.15 µF

1.5 k

Ω

Earth Ground

AC Voltmeter (0.75 V)

Fig. A. Using an AC voltmeter to check AC leakage.

– 3 –

Trouble Light

AC Outlet Box

Ohmmeter

Fig. B. Checking for earth ground.

Cold-water Pipe

KL-W7000/W9000

RM-Y980

TABLE OF CONTENTS

Section Title Page Section Title Page

1. GENERAL .................................................................. 5

2. DISASSEMBLY

2-1. Rear Cover Removal ........................................... 18

2-2. Chassis Assy Removal ........................................ 18

2-3. Service Position ................................................... 18

2-4. U Board Removal ................................................ 18

2-5 Power Block and K Board Removal ................... 19

2-6. Filter Removal ..................................................... 19

2-7. Lamp Removal .................................................... 20

2-8. HA and HB Boards Removal .............................. 20

2-9-1. Screen Frame Removal [W7000] ........................ 20

2-9-2. Screen Frame Removal [W9000] ........................ 20

2-10-1.C Board Removal ................................................ 21

2-10-2.Extension Cable (C Board) .................................. 21

2-11. Optical Unit Removal .......................................... 21

3. CIRCUIT ADJUSTMENTS ................................ 22

4. DIAGRAMS

4-1. Block Diagrams ................................................... 39

4-2. Circuit Boards Location....................................... 53

4-3. Schematic Diagrams and Printed

Wiring Boards ................................................. 54

(1) Schematic Diagrams of HA,HB, K,

TA and TB Boards ........................................... 55

(2) Schematic Diagram of A (1/3) Board ................... 63

(3) Schematic Diagram of A (2/3) Board ................... 67

(4) Schematic Diagram of A (3/3) Board ................... 71

(5) Schematic Diagram of BB Board.......................... 75

(6) Schematic Diagram of U Board ............................ 83

(7) Schematic Diagram of C (1/2) Board.................... 87

(8) Schematic Diagram of C (2/2) Board.................... 91

(9) Schematic Diagrams of G and GA Boards ............ 95

4-4. Semiconductors ................................................... 99

5. EXPLODED VIEWS

5-1. Chassis [W7000] ................................................. 101

5-2. Front Cover [W7000] .......................................... 102

5-3. Screen Mirror Block and Optics Unit [W7000] .. 103

5-4. Chassis [W9000] ................................................. 104

5-5. Front Cover [W9000] .......................................... 105

5-6. Screen Mirror Block and Optics Unit [W9000] .. 106

6. ELECTRICAL PARTS LIST ............................ 107

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AUX COMPOSANTS RELATIFS À LA

SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE MARQUE SÉCURITÉ. NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNE-MENT EST SUSPECTÉ.

¡ SONT CRITIQUES POUR LA

– 4 –

The operating instructions mentioned here are partial abstracts

-EN

Welcome!Precautions

This projection monitor operates on extremely high voltage. To prevent fire or electric shock, please follow the precautions below.

On safety

• Operate the monitor only on 100 V to 120 V AC.

• One blade of the plug is wider than the other for

safety purposes and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• Should any liquid or solid object fall into the

cabinet, unplug the monitor and have it checked by qualified personnel before operating it further.

• Unplug the monitor from the wall outlet if you are

not going to use it for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The fans inside the monitor continue working for a

while even after the monitor has been turned off. Do not unplug the monitor from the AC outlet while the fans are working.

On installation

• To prevent internal heat build-up, do not block the ventilation openings.

• Do not install the monitor in a hot or humid place, or in a place subject to excessive dust or mechanical vibration.

On screen

The screen surface is easily scratched. Do not rub, touch or tap it with sharp or abrasive objects. Be especially careful when transporting the monitor.

On LCD panel

• Do not expose the screen to direct sunlight. It may damage the LCD panel.

• When the monitor is used in a cold place, the image may look lengthened. This is not a malfunction. The image will become normal when the temperature rises.

• When the same static picture has been displayed continuously, an afterimage impression of that picture may remain on the screen. This will disappear after a certain time.

• If you turn on the monitor immediately after power has been restored at an interruption, an LCD burn may occur. This is not a malfunction. The image will become normal after a certain time.

On blanking around the pciture

The monitor displays black masks between the picture and the screen vessel because the monitor under-scans to obtain the necessary space on the screen to display the picture. This is called blanking. Note that the black masks on each vessel are not uniform. The blanking on the video picture will be wider to optimize picture.

On moisture condensation

If the projection monitor is transported directly from a cold to a warm location, or if the room temperature has changed suddenly, the picture may be blurred or show poor color. This is because moisture has condensed on the lenses inside. If this happens, let the moisture evaporate before using the monitor.

On cleaning

• Clean the cabinet of the monitor with a dry soft cloth. Stubborn stains may be removed with a cloth slightly dampened with solution of mild soap and water, then wipe it with a dry soft cloth. Do not use any type of solvent such as alcohol, benzine, thinner or insecticide. Such solvent may damage the finish of the monitor or erase the indications on the panel.

• Wipe the screen with a dust remover (supplied) occasionally, as the screen easily catches dust. The dust remover is washable. Wash it with warm water or mild detergent solution.

• Stubborn stains on the screen may be removed with a soft cloth slightly dampened with solution of mild soap and water.

• If the picture becomes dark after using the monitor for a long period of time, it may be necessary to clean the inside of the monitor. Consult qualified service personnel.

Screen vessel

Picture

Blanking

Getting Started

-EN

p for KL-W9000

Vertical viewing area (side view)

Horizontal viewing area (top view)

Getting Started

Step 1: Installing the projection monitor

Optimum viewing area

For the best picture quality, install the monitor within the areas shown below.

p for KL-W7000

Vertical viewing area (side view)

Horizontal viewing area (top view)

30°

2 m

75°

2 m

35°

75°

1.5 m

from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.

– 5 –

SECTION 1

GENERAL

-EN

Getting Started

Pass a strong cord or a chain through each

bracket mounted in step 1, and then secure it to a wall or a pillar, etc.

Using the buckle

You can also use the supplied buckle to secure the monitor to the stand.

Attach the buckle to the stand on which the monitor is mounted.

Tighten the supplied screw firmly.

Insert the buckle until it clicks.

Pull the belt to fasten.

Carrying your monitor

Be sure to grasp the areas indicated by the arrows when carrying the monitor, and to use more than two people. Never grasp the front panel.

p for KL-W7000

p for KL-W9000

Stabilizing the monitor

Using the brackets

After setting up, secure the monitor to a wall, etc. with the supplied brackets.

Mount the two supplied brackets with the

screws to the upper rear sides of the monitor.

Bracket (supplied)

Belt

Getting Started

-EN

Using the rear RGB 1 IN connector

* The HD15–HD15 adaptor (supplied) may be needed for some

models. The male side (without the No. 9 pin) of the adaptor should be connected to the computer.

For customers using the supplied HD15–HD15 adaptor

This monitor uses a No. 9 pin in the video signal connector for DDC1 and DDC2B compatibility. Some PC systems which are not compatible with either DDC1 or DDC2B may not accept the No. 9 pin. If you are not sure whether your PC system accepts the No. 9 pin or not, use the HD15 (Female) – HD15 (Male without the No. 9 pin) adapter (supplied).

Step 2: Hookup

Before making the connection, turn off the power and disconnect the AC power cords of the monitor and the equipment to be connected. Refer to the instruction manual of the equipment you connect.

Connecting to an IBM PC/AT or compatible computer

Connect the RGB 2 IN connector on the front or the RGB 1 IN connector at the rear of the monitor to the video/audio outputs of the computer using the supplied RGB signal cable (D-sub 15 pin ˜ D-sub 15 pin).

Using the front RGB 2 IN connector

Rear of the monitor

RGB signal cable (supplied)

HD15–HD15 adaptor (supplied)*

to video output

Audio connecting cord (phono plug × 2 ˜ stereo minijack) (not supplied)

to audio output

IBM PC/AT or compatible computer

Front of the monitor

RGB signal cable (supplied)

HD15–HD15 adaptor (supplied)*

to video output

Audio connecting cord (stereo minijack ˜ stereo minijack) (not supplied)

to audio output

IBM PC/AT or compatible computer

Male side (without the No.9 pin)

INPUT SELECT

VIDEO

AUDIO

VIDEO 2 IN

RESET

RGB AUDIO

RGB 2 IN

RGB 1 IN

AUDIO

RGB

VIDEO IN

S VIDEO

VIDEO

AUDIO

VIDEO

OUT

– 6 –

-EN

Getting Started

INPUT SELECT

VIDEO

AUDIO

VIDEO 2 IN

RESET

RGB AUDIO

RGB 2 IN

Connecting to a Macintosh or compatible computer

Using the front RGB 2 IN connector

Using the rear RGB 1 IN connector

About the supplied Macintosh adaptor

The supplied Macintosh adaptor is compatible with Macintosh LC, Performa, Quadra and Power Macintosh series computers. Macintosh II series and some version of PowerBook models may need an another adaptor with micro switches (not supplied).

Front of the monitor

RGB signal cable (supplied)

Macintosh adaptor (supplied)

to video output

Audio connecting cord (stereo minijack ˜ stereo minijack) (not supplied)

to audio output

Macintosh or compatible computer

Rear of the monitor

RGB signal cable (supplied)

Macintosh adaptor (supplied)

to video output

to audio output

Macintosh or compatible computer

Audio connecting cord (phono plug × 2 ˜ stereo minijack) (not supplied)

RGB 1 IN

AUDIO

RGB

VIDEO IN

S VIDEO

VIDEO

AUDIO

VIDEO

OUT

Getting Started

-EN

Preset and user modes

Preset modes

The monitor has nine factory preset modes for the most popular industry standards as shown below.

No. Resolution Horizontal Vertical Graphics

(dots × frequency frequency mode lines) (kHz) (Hz)

1 640 × 400 31.468 70.086 VGA mode

(Text)

2 640 × 480 31.468 59.94 VGA mode

(Graphics)

3 800 × 600 37.879 60.317 SVGA VESA 4 800 × 600 46.875 75.000 SVGA VESA 5 1024 × 768 48.363 60.004 VESA 6 864 × 480 31.469 59.94 Sony Wide-VGA* 7 1072 × 600 37.879 60.317 Sony Wide-SVGA* 8 1376 × 768 48.363 60.004 Sony Wide-XGA* 9 640 × 480 34.954 66.667 Macintosh 13" color

* For the timing chart of the signals, see page 28.

User modes

When using a video mode that is not one of the preset modes, some fine tuning may be required to optimize the display to your preference. Simply adjust the monitor according to the adjustments instructions on page 16. The adjustments will be stored automatically and recalled whenever that mode is used. A total of 15 user-defined modes can be stored in memory. If a 16th mode is entered, it will replace the first.

Recommended horizontal timing conditions

Horizontal sync width should be more than 1.0 µsec. Horizontal blanking width should be more than 3.6 µsec.

When “OUT OF SCAN RANGE” appears on the screen

The monitor receives a signal whose frequency range is not within that specified for the monitor.

Notes

• When projecting a Wide-VGA, Wide-SVGA or Wide-XGA signal, set the picture mode to FULL. In NORMAL mode, the picture with aspect ratio 16:9 will be compressed to aspect ratio 4:3 and appear lengthened vertically. For details, see page 15.

• The monitor does not accept an interlace mode signal.

Plug & Play

This monitor complies with the DDC

1 and DDC2B which are the Display Data Channel (DDC) standards of VESA. When a DDC1 host system is connected, the monitor synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification Data) to the data line. When a DDC2B host system is connected, the monitor automatically switches to each communication.

For customers using Windows 95

Install the new model information from the “Windows 95 Monitor Information Disk” into your PC. (To install the file, refer to the supplied “About the Windows 95 Monitor Information Disk/File.”) This monitor complies with the “VESA DDC” Plug&Play standard. If your PC/video card complies with DDC, select “Plug and Play Monitor (VESA DDC)” as “Monitor type” from “Control Panel” in Windows 95. Some PC/video cards do not comply with DDC. Even if your computer complies with DDC, it may have some problems connecting with this monitor. In this case, select this monitor’s model name (KL-W7000 or KL-W9000) as “Monitor type” in Windows 95.

– 7 –

-EN

Getting Started

Connecting two VCRs for editing

The monitor outputs signals from the VIDEO IN jacks through the VIDEO OUT jacks. With two VCRs connected to the VIDEO IN and VIDEO OUT jacks, you can edit the tape.

Note

For the RGB signal input from the RGB 1/2 IN connectors, the monitor outputs only the audio signal.

Connecting the AC power cord

Connect the supplied power cord to the AC IN socket of the monitor and to a wall AC outlet.

RGB 1 IN

AUDIO

RGB

VIDEO IN

S VIDEO

VIDEO

AUDIO

VIDEO

OUT

Connecting to video equipment

To a VCR not equipped with an S video connector

You can also use the VIDEO 2 IN jacks on the front of the monitor for the video/audio connections.

To an S video equipped VCR

Rear of the monitor

to VIDEO 1 IN or VIDEO 3 IN

VMC-810S/820S (not supplied)

VCR

to video/audio outputs

to VIDEO 1 IN or VIDEO 3 IN

YC-810S (not supplied)

VCR

to S video/audio outputs

Rear of the monitor

VMC-810S/ 820S (not supplied)

VCR for playback

VMC-810S/820S (not supplied)

VCR for recording

Rear of the monitor

to an AC outlet

AC power cord (supplied)

to AC IN

Note

When you connect the cable to both the VIDEO jack and the S VIDEO connector, the picture from the S VIDEO connector is displayed on the monitor screen.

Rear of the monitor

to video/audio outputs

to video/ audio inputs

RGB 1 IN

AUDIO

RGB

VIDEO IN

S VIDEO

VIDEO

AUDIO

VIDEO

OUT

RGB 1 IN

AUDIO

RGB

VIDEO IN

S VIDEO

VIDEO

AUDIO

VIDEO

OUT

to VIDEO OUT

to VIDEO 1 IN or VIDEO 3 IN

Getting Started

-EN

OPTION N AUTO SHUT OFF:OFF LANGUAGE: ENGLISH

Step 3: Setting up the remote control

Inserting batteries

Insert two size AA (R6) batteries (supplied) by matching the + and – on the battery to the diagram inside the battery compartment.

Notes

• Under normal conditions, batteries will last up to six months. If the remote control does not operate properly, the batteries may be worn out. When replacing batteries, replace both of them with new ones.

• Do not mix old batteries with new ones or mix different types of batteries together.

• If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent the electrolyte from leaking, remove the batteries when you don‘t plan to use the remote control for a long period of time.

• Do not handle the remote control roughly. Do not drop it, step on it, or let it get wet.

• Do not place the remote control in direct sunlight, near a heater, or where the humidity is high.

If you prefer Spanish or French to English, you can change the menu language.

Press MENU.

Press V or v to select OPTION, and press ENTER.

Press V or v to select LANGUAGE, and press ENTER.

Press B, V, v or b to select your favorite language, “ENGLISH,” “FRANCAIS (French)” or “ESPANOL (Spanish).”

Press MENU to return to the original screen.

Notes

• You can operate the menu using the buttons on the monitor. The VOLUME + button functions the same as V and b, and VOLUME – as v and B.

• You cannot use the AUTO SHUT OFF function for the input from VIDEO IN. (See page 22.)

Changing the menu language

ENTER

CENTER/ SIZE

VOL

ENTER

– 8 –

-EN

Operations

If the STANDBY indicator on the front of the monitor is lit in orange, press POWER on the remote control to turn on the power.

Press the power switch (green) on the monitor if the STANDBY indicator is not lit.

The green u (power) indicator flashes, then lights up.

Turn on the power of the connected equipment.

Press RGB or VIDEO to select the input you want to watch.

The selected input indication is displayed on the screen.

To watch a computer picture input from the RGB IN connector

Each time you press RGB, the display changes as follows:

RGB 1 ˜ RGB 2

To watch a video picture input from the VIDEO IN jacks

Each time your press VIDEO, the display changes as follows:

VIDEO 1 n VIDEO 2 n VIDEO 3

You can also select the input by pressing INPUT SELECT on the monitor. Each time you press INPUT SELECT, the display changes as follows:

RGB 1 n RGB 2 n VIDEO 1 n VIDEO 2 n VIDEO 3

The input signal indication will automatically disappear.

Press VOL +/– (VOLUME +/–) to adjust the volume.

Remote control Monitor

Projecting the picture

Operations

CENTER/ SIZE

VOL

ENTER

VIDEO

MUTING

DISPLAY

POWER

RGB WIDE

POWER

RGB

INPUT SELECT

VIDEO

VOL

VOLUME

–

VOLUME

LAMP

INPUT SELECT

STANDBY

ENTER

Power switch (green)

-EN

Operations

Watching the video picture in wide mode

You can enjoy a variety of wide mode picture.

Press WIDE until the mode you want appears on the screen.

Each time you press WIDE, the mode changes as follows:

NORMAL n FULL n ZOOM n SUB TITLE n WIDE ZOOM

To turn off the monitor

Press POWER on the remote control. The monitor enters standby mode and the STANDBY indicator lights up. To turn off the main power, press the power switch (green) on the monitor.

Note

To protect the lamp mounted as a source of light, if you try to turn on the power within about 30 minutes after the power has been turned off, the u (power) indicator flashes and the picture does not appear.

Muting the sound

Press MUTING. “MUTING” appears on the screen. To restore the sound, press MUTING again, or press VOL+.

Displaying on-screen information

Press DISPLAY to display the following information on the screen.

To make the on-screen information disappear, press DISPLAY again.

Current input signal

Picture mode (page 14)

Current input signal frequency when the RGB signal* is input

Watching the picture in wide picture mode

WIDE

CENTER/ SIZE

VIDEO

MUTING

DISPLAY

POWER

RGB WIDE

(continued)

*fH: Horizontal frequency

fV: Vertical frequency “OUT OF SCAN RANGE” appears if the scanning frequency range is not within the acceptable limits. (See page 9.)

NORMAL

RGB 1

fv:75

fh:37.5

– 9 –

-EN

Operations

The wide-format picture is enlarged and the subtitle area is compressed so that the picture is aligned with the screen size.

The picture is enlarged horizontally and vertically and the upper and lower portions of the picture are compressed to the screen size.

Recommended picture mode

When watching a picture with normal aspect ratio 4:3

Select NORMAL.

Select WIDE ZOOM.

When watching a picture recorded after a 16:9 picture has been compressed to aspect ratio 4:3

Select FULL.

When watching a wide-format movie or software with black bands and subtitles (with subtitles inside the picture)

Select ZOOM.

The wide-format picture is enlarged horizontally and vertically to the screen size.

The picture with normal ratio 4:3 is displayed as it is.

When watching a movie or software with subtitles (with subtitles outside the picture)

Select SUB TITLE.

Note

• You can also change the picture mode by using the menu.

Notes on wide picture modes

• Select a picture mode taking into account that one which changes the aspect ratio of the original picture will provide an appear different from that of the original image.

• If the monitor is used for profit or for public viewing, modifying the original picture by changing picture modes may constitute an infringement of the rights of authors or producers which are legally protected by laws.

• When a normal 4:3 picture is watched in WIDE ZOOM mode, the surrounding portions may be cut off or modified. The original picture can be viewed in NORMAL mode.

Hello,Anne.

Good-bye,Jane. Good-bye.

The picture compressed to aspect ratio 4:3 is enlarged horizontally to the screen size.

The picture with aspect ratio 16:9 is enlarged to the screen size as it is.

-EN

Operations

ASPECT N ASPECT: ZOOM V SCROLL: 0

Adjusting the vertical position of the video picture

You can scroll the picture up or down when:

• the upper or lower portions of the picture in WIDE ZOOM mode are cut off.

• you want to move the picture in ZOOM mode as you like.

• subtitles are lost from the screen in SUB TITLE mode.

Scrolling the picture functions on the WIDE ZOOM, ZOOM and SUB TITLE modes only.

Press MENU.

Press V or v to select ASPECT, and press ENTER.

Press V or v to select V SCROLL, and press ENTER.

Press V or v to adjust the vertical position of the picture.

Note

• You can operate the menu using the buttons on the monitor.

The VOLUME + button functions the same as V and b, and VOLUME – as v and B.

The picture with aspect ratio 16:9 is enlarged to the screen size.

Watching the computer picture in wide picture mode

If you set the picture mode to FULL when a WideVGA, Wide-SVGA or Wide-XGA signal is received, you can watch the picture with aspect ratio 16:9 as it is. The Wide-VGA, Wide-SVGA and Wide-XGA signals are independently standardized by Sony. When you use the signals with the timing chart on page 28, you can obtain an effective wide mode picture.

Press WIDE to display FULL or NORMAL on the screen.

Each time your press WIDE, you can select FULL and NORMAL alternately.

When a Wide-VGA, Wide-SVGA or Wide-XGA signal is received

NORMAL mode FULL mode

When a conventional VGA, SVGA or XGA signal is received

NORMAL mode FULL mode

Adjusting the position of a computer picture

You can move the picture up, down, right or left to make it easy to watch by using the SIZE/CENTER button. For details, see page 16.

If you watch the Wide-VGA, Wide-SVGA or WideXGA signal in NORMAL mode

A 16:9 picture will be compressed horizontally to a 4:3 picture.

ENTER

to move the picture up

to move the picture down

WIDE

The picture with aspect ratio 4:3 is enlarged horizontally to the screen size.

CENTER/ SIZE

VOL

ENTER

CENTER/ SIZE

VOL

ENTER

– 10 –

-EN

Operations

Adjusting the position (CENTER)

After projecting the picture from a computer, you may need to adjust the position of the picture to fit the monitor screen. You can also move the picture as you like. The setting is only for the input signal displayed on the screen.

Press CENTER/SIZE until the CENTER adjustment screen appears.

Press B, b, V or v to adjust the position.

For horizontal adjustment press B or b. (H CENTER)

For vertical adjustment press V or v. (V CENTER)

The CENTER adjustment screen automatically disappears after about 10 seconds if you do not press any button. You can also erase the CENTER adjustment screen by pressing CENTER/SIZE again.

CENTER/ SIZE

VIDEO RGB WIDE

Adjusting the computer picture

CENTER/ SIZE

To reset to the factory preset setting

Press RESET on the monitor. At the same time, the picture size and video/audio settings (pages 17 to 21) are also reset to the factory preset levels.

Note

• You can adjust the position by using the CENTER/SIZE and

ı/◊/√/∫ buttons on the monitor.

Adjusting the picture size (SIZE)

After projecting the picture from a computer, you may need to adjust the picture size to fit the monitor screen. The setting is only for the input signal displayed on the screen.

Press CENTER/SIZE until the SIZE adjustment screen appears.

Press B, b, V or v to adjust the picture size.

For horizontal adjustment press B or b. (H SIZE)

For vertical adjustment press V or v. (V SIZE)

The SIZE adjustment screen automatically disappears after about 10 seconds if you do not press any button. You can also erase the SIZE adjustment screen by pressing CENTER/SIZE again.

To reset to the factory preset setting

Press RESET on the monitor. At the same time, the picture position and video/audio settings (pages 17 to

21) are also reset to the factory preset levels.

Notes

• For a picture with resolution of 640 × 350, 640 × 400 or 640 ×

480, the vertical size cannot be increased from the size that was projected the first time.

• You can adjust the size using the CENTER/SIZE and ı/◊/√/ ∫ buttons on the monitor.

CENTER/ SIZE

V: to move the picture up v: to move the picture down

b: to increase horizontal size B: to decrease horizontal size

V: to increase vertical size v: to decrease vertical size

b: to move the picture right B: to move the picture left

CENTER

H CENTER

V CENTER

SIZE

H SIZE

V SIZE

-EN

Operations

VIDEO/AUDIO N PRESENTATION STANDARD MOVIE AV MEMORY VIDEO ADJUST AUDIO ADJUST

The video/audio mode feature allows you to choose four different modes of picture/sound settings. Choose the one that best suits the type of program that you want to watch.

Press MENU.

Press V or v to select VIDEO/AUDIO, and press ENTER.

Press V or v to select the desired item, and press ENTER.

Selecting the preset picture viewing mode

ENTER

To reset to the factory preset setting

Press RESET on the monitor. When watching a computer picture, the mode resets to PRESENTATION. When watching a video picture, the mode resets to STANDARD. At the same time, the position and size of a computer picture (page 16) are also reset to the factory preset levels. The settings in AV MEMORY do not reset.

Note

• You cannot adjust the settings in modes other than AV MEMORY.

Choose To

PRESENTATION Watch the picture input from a

computer.

STANDARD Watch the picture input from video

equipment. MOVIE Watch a movie. AV MEMORY Adjust the quality of the picture/sound

to suit your taste. (For details, see pages

18–21.)

Press MENU to return to the original screen.

CENTER/ SIZE

VOL

ENTER

– 11 –

-EN

Operations

N

CONTRAST

 BRIGHTNESS COLOR HUE SHARPNESS RESET

VIDEO ADJUST

BRIGHTNESS

VIDEO ADJUST

(2) Press ENTER.

Adjust the selected item.

Press V, b, v or B to adjust the item, and press ENTER.

To adjust other items, repeat steps 4 and 5.

Press MENU to return to the original screen.

To reset to the factory preset setting

Move the cursor (”) to RESET at the bottom of the VIDEO ADJUST menu, and press ENTER.

Notes

• When the RGB signal is input, COLOR, HUE and SHARPNESS cannot be adjusted.

• You can adjust the items in AV MEMORY for each input from VIDEO 1, 2 and 3, and RGB 1 IN and RGB 2 IN.

• You can operate the menu using the buttons on the monitor. VOLUME + functions the same as V and b, and VOLUME – as v and B.

ENTER

Adjusting the picture

(AV MEMORY)

You can adjust the quality of the picture to suit you taste and store the settings into AV MEMORY.

Press MENU.

Press V or v to select VIDEO/AUDIO, and press ENTER.

Press V or v to select VIDEO ADJUST, and press ENTER.

Select the item you want to adjust. For example:

(1) To adjust the brightness, press V or v to move

the cursor (”) to BRIGHTNESS.

ENTER

CENTER/ SIZE

VOL

ENTER

Item

CONTRAST

BRIGHTNESS COLOR

HUE

SHARPNESS

Press v or B to

Decrease picture contrast.

Darken the picture. Decrease color

intensity. Make picture tones

become purplish. Soften the picture.

Press V or b to

Brighten the picture.

Brighten the picture. Increase color intensity.

Make picture tones become greenish.

Sharpen the picture.

ENTER

-EN

Operations

N

CONTRAST

 BRIGHTNESS COLOR HUE SHARPNESS RESET

VIDEO ADJUST

N

NR: OFF

 H-WHITE: ON COLOR TEMP: MEDIUM RESET



VIDEO ADJUST

Adjusting the picture in more details

You can adjust the picture with the NR (noise reduction), H-WHITE and COLOR TEMP (temperature) options.

Press MENU.

Press V or v to select VIDEO/AUDIO, and press ENTER.

Press V or v to select VIDEO ADJUST, and press ENTER.

Press V or v to move the cursor (”) to RESET, then press v again.

Select the desired item with V or v, then press ENTER.

Press V or v to adjust the item, then press ENTER.

To adjust other items, repeat steps 5 and 6.

Press MENU to return to the original screen.

To reset to the factory preset setting

Move the cursor (”) to RESET at the bottom of the VIDEO ADJUST menu, and press ENTER.

Notes

• You can adjust the items in AV MEMORY for each input from VIDEO 1, 2 and 3, and RGB 1 IN and RGB 2 IN.

• You can operate the menu using the buttons on the monitor. VOLUME + functions the same as V and b, and VOLUME – as v and B.

ENTER

Choose

NR (Noise Reduction)

H-WHITE

COLOR TEMP (Color temperature)

Reduce picture noise. You can choose LOW or HIGH position.

Emphasize the white color with the ON position.

Make the white color warm (reddish) with the LOW position. Make it cool (bluish) with the HIGH position.

CENTER/ SIZE

VOL

ENTER

– 12 –

-EN

Operations

You can adjust the quality of the sound to suit you taste and store the settings into AV MEMORY.

Press MENU.

Press V or v to select VIDEO/AUDIO, and press ENTER.

Press V or v to select AUDIO ADJUST, and press ENTER.

Select the item you want to adjust. For example:

(1) To adjust the bass, press V or v to move the

cursor (”) to BASS.

(2) Press ENTER.

N

TREBLE

 BASS BALANCE EFFECT: OFF RESET

AUDIO ADJUST

Adjust the selected item.

Press V, b, v or B to adjust the item, and press ENTER.

To adjust other items, repeat steps 4 and 5.

Press MENU to return to the original screen.

To reset to the factory preset setting

Move the cursor (”) to RESET at the bottom of the AUDIO ADJUST menu, and press ENTER.

Notes

• You can adjust the items in AV MEMORY for each input from VIDEO 1, 2 and 3, and RGB 1 IN and RGB 2 IN.

• You can operate the menu using the buttons on the monitor. VOLUME + functions the same as V and b, and VOLUME – as v and B.

Adjusting the sound

(AV MEMORY)

ENTER

Item

TREBLE

BASS

BALANCE

Press V or b to

Increase the treble response.

Increase the bass response.

Emphasize the right speaker’s volume.

Press v or B to

Decrease the treble response.

Decrease the bass response.

Emphasize the left speaker’s volume.

BASS

AUDIO ADJUST

CENTER/ SIZE

VOL

ENTER

-EN

Operations

N

TREBLE

 BASS BALANCE EFFECT: OFF RESET

AUDIO ADJUST

Audio effect mode allows you to enjoy dynamic sound with surround-like effect.

Press MENU.

Press V or v to select VIDEO/AUDIO, and press ENTER.

Press V or v to select AUDIO ADJUST, and press ENTER.

Press V or v to select EFFECT, and press ENTER.

Press V or v to select the desired item, and press ENTER.

Press MENU to return to the original screen.

To reset to the factory preset setting

Move the cursor (”) to RESET at the bottom of the AUDIO ADJUST menu, and press ENTER.

Notes

• You can adjust the items in AV MEMORY for each input from VIDEO 1, 2 and 3, and RGB 1 IN and RGB 2 IN.

• You can operate the menu using the buttons on the monitor. VOLUME + functions the same as V and b, and VOLUME – as v and B.

ENTER

Selecting the audio effect

(EFFECT)

CENTER/ SIZE

VOL

ENTER

Choose

HALL SURROUND 1

HALL SURROUND 2 SIMULATED STEREO

OFF

Receive dynamic threedimensional sound.

Watch a movie. Receive monaural sound with

surround-like effect. Cancel audio effect.

ENTER

– 13 –

-EN

Operations

OPTION N AUTO SHUT OFF:OFF LANGUAGE: ENGLISH

You can set the monitor to turn off when the time you specify has passed after the input of the sync signal from the computer shut off.

Press MENU.

Press V or v to select OPTION, and press ENTER.

Press V or v to select AUTO SHUT OFF, and press ENTER.

Press B or b to select 60 (minutes), 90 (minutes) or 120 (minutes), and press ENTER.

Press MENU to return to the original screen.

After the time you specify in step 4 has passed after cancellation of the input of the sync signal, the power turns off and the STANDBY indicator and the u indicator will light up.

The power turns on if you press POWER on the remote control or a signal is input from the computer again.

Note

• You cannot use this function for the input from VIDEO IN.

Turning the power off automatically

(AUTO SHUT OFF)

ENTER

CENTER/ SIZE

VOL

ENTER

-EN

Additional Information

The air filter should be cleaned once a month. When it becomes difficult to remove the dust, replace the filter with a new one. To clean the filter, follow the steps below.

Turn off the power switch on the monitor and unplug the power cord.

Remove the front panel from the monitor.

Pull the panel towards you, holding its left end. Be careful not to damage your nails.

Pull the air filter upwards to remove.

Cleaning the air filter

Remove the dust from the filter with a vacuum cleaner.

Attach a new filter to the monitor.

Fit the six projections securely.

Mount the front panel.

Be careful not to injure the speakers.

Notes

• Clean the air filter periodically. Otherwise, the temperature inside the monitor may rise abnormally.

• Do not use a torn filter. Fit the six projections on the filter to the monitor securely. Dust inside the monitor may cause distorted picture and also fire.

• Be sure to attach the air filter securely. Otherwise, the monitor will not turn on.

• Contact your Sony dealer for a new filter.

Hold the monitor tightly.

Additional Information

Vacuum cleaner

– 14 –

-EN

Additional Information

Replacing a lamp

If the screen becomes dark, the color looks unusual, or the LAMP indicator on the front of the monitor flashes, it is time to replace the lamp with a new one.

Before replacement

• Be sure to use the Sony XL-100U lamp unit (not supplied) for replacement. Use of other lamps causes damage to the monitor.

• Do not remove the lamp for any purpose other than replacement.

• Before replacement, be sure to turn off the monitor and unplug the power cord.

• When replacing the lamp, let it cool down completely, as the surface of the lamp remains hot for at least 30 minutes after the power has been switched off.

• Do not leave the removed lamp near the inflammable materials.

• Do not pour water onto the removed lamp, nor put any object inside the lamp.

• Do not put inflammable materials and metal objects inside the lamp receptacle on the monitor, after removing the lamp. Do not touch the receptacle.

• Fit the new lamp securely, otherwise the screen may become dark, or it may cause fire.

Turn off the power switch on the monitor and unplug the power cord.

Wait at least 30 minutes to allow the lamp to cool down before replacing it .

Remove the front panel.

Untighten the screw with a coin or similar object to remove the lamp cover.

Loosen the two screws that secure the lamp, then pull out the lamp.

The lamp is very hot immediately after use. Never touch the front glass of the lamp or the surrounding parts.

Loosen the two screws with the hexagon head wrench (supplied with the lamp).

Pull out straight towards you by holding the handle.

Replace the removed lamp into the empty box of the replacement lamp.

Mount the new lamp and tighten the two screws securely.

Mount the lamp cover and tighten the screw.

Mount the front panel.

Be careful not to damage the speakers of the monitor.

Notes

• Do not touch the front glass of a new lamp or the glass of the lamp receptacle. This may reduce picture quality or lamp life.

• Be sure to attach the lamp securely. Otherwise, the monitor will not turn on.

• A laud sound may be heard when the lamp burns. This is not dangerous.

• Consult your Sony dealer for the XL-100U lamp unit.

Pull the panel towards you, holding its right end. Be careful not to damage your nails.

Hold the monitor tightly.

-EN

Additional Information

Troubleshooting

If the problem persists after trying the methods below, contact your nearest Sony dealer.

No picture

Check that the power cord is connected firmly.

Is the power of the monitor turned on?

Is the air filter mounted securely? (page 23)

Is the lamp cover attached securely? (page

24)

Check that the power of the connected equipment is turned on.

Try to press any key on the connected computer.

Check that the RGB signal cable or audio/ video cords are properly connected. (The supplied HD15-HD15 adaptor may be needed for some models of IBM PC/AT or compatible computers. For a Macintosh or compatible computer use the supplied Macintosh adaptor.)

Make sure that no pins on the HD15 connectors are bent.

Check that the video card is seated completely in the proper bus slot.

Check that the frequency range of the input signal is within that specified for the monitor. (If not, “OUT OF SCAN RANGE” appears on the screen.)

The monitor does not accept an interlace mode signal.

For customers using Windows 95 — If “KLW7000” or “KL-W9000” is not displayed as “Monitor type” when selecting “SONY” as “Manufacturer” from the device select screen in Windows 95, select “Standard monitor” as “Manufacturer” and “Plug and Play monitor (VESA DDC)” as “Monitor type,” or select “SONY Corporation” as “Manufacturer” and “KL-W7000” or “KLW9000” as “Monitor type.”

Picture and sound output are delayed

When the green u (power) indicator on the front is flashing, the monitor is warming up.

It will take 30 minutes for the monitor to display the picture again after the monitor is switched off.

Screen lit and cannot see the picture

Be sure that you are watching the monitor within the optimum viewing area. (page 5)

Good picture, no sound

Press VOL+ (VOLUME+).

Press MUTING so that “MUTING” disappears from the screen. (page 13)

Fuzzy picture

Set the NR option in the VIDEO ADJUST menu to LOW or HIGH.

If you use the monitor in a cold place, moisture condensation may have occurred. Leave the monitor as it is to let moisture evaporate.

Dark picture

Replace the lamp for the light source with a new one. (page 24)

No color, abnormal color

Adjust the picture in the VIDEO ADJUST menu. (page 18)

Double images

Use of an extension cable, excessive cable length or loose connection can produce this symptom.

Computer picture not centered or sized properly

Adjust the centering and size so that the picture fits the screen. (page 16)

Distorted picture

Check your video card manual for proper monitor setting.

Check that the frequency and the graphic mode at which you are trying to input is within the acceptable range. (page 9) Even within the proper range some video cards may have a sync pulse that is too narrow for the monitor to sync correctly.

No picture, no sound from the connected equipment

Are all the connecting cables connected?

Try to press the RGB or VIDEO button on the remote control. (page 12)

The remote control does not function.

Are the batteries worn out?

The humming noise of fans is heard even after the monitor has been turned off.

The fans installed inside the monitor are working to prevent internal heat build-up. They will stop about 2 minutes later.

– 15 –

-EN

Additional Information

What flashing of the indicators on the front of the monitor means

The u (power) (green), STANDBY (orange) and/or LAMP (red) indicators indicate the conditions of the monitor and warnings by lighting or flashing, as follows.

The u indicator lights.

The power of the monitor is on.

The STANDBY indicator lights.

The monitor is in standby mode. The monitor is turned on by pressing POWER on the remote control.

The u and STANDBY indicators light.

The Auto Shut Off function works. The monitor has been turned off when the time you specify has passed after the input of the computer is cut off.

The u indicator flashes.

The lamp for the light source is ready to turn on. Within 30 minutes the picture is displayed on the screen.

The LAMP and STANDBY indicators flash.

The air filter or the lamp cover is not attached securely. When you correct, the STANDBY lamp lights up and the monitor enters the standby mode. (pages 23, 24)

The LAMP indicator flashes.

The lamp for the light source burns out. Replace it with new one. (page 24)

The LAMP, STANDBY and u indicators flash.

The temperature inside the monitor has risen abnormally, or the fans have stopped. Check that the air filter is not clogged and the ventilation holes are not blocked. After a while turn on the monitor. (page 23)

If the monitor is not recovered after correcting the problems, contact with qualified Sony personnel.

-EN

Additional Information

Wide-VGA Wide-SVGA Wide-XGA

Pixel Clock (MHz) 34.238 53.94 87.44 1dot (nsec) 29.207 18.539 11.436 1H (µsec) 31.777 26.4 20.676 H-Active (µsec) 25.235 19.874 15.736 H-Blank (µsec) 6.542 6.526 4.94 H-Front porch (µsec) 0.701 0.89 0.366

(dots) 24 48 32

H-Sync (µsec) 3.738 3.263 2.104

(dots) 128 176 184

H-Back porch (µsec) 2.103 2.373 2.47

(dots) 72 128 216 H-Sync Polarity – – – V-TTI Time (Lines) 525 628 806 V-Addr Time (Lines) 480 600 768 V-Blank Start (Lines) 488 600 768 V-Blank Time (Lines) 29 28 38 V-Sync Start (Lines) 490 601 771 V Bottom Border 8 0 0

(Lines) V Front Porch (Lines) 2 1 3 Ver Sync Time (Lines) 2 4 6 V Back Porch (Lines) 25 23 29 V Top Border (Lines) 8 0 0 V-Sync Polarity + + +

Timing chart for the Wide-VGA, WideSVGA and Wide-XGA signals

– 16 –

-EN

Additional Information

VOLUME

LAMP

INPUT SELECT

STANDBY

RGB 2 IN

VIDEO

AUDIO

VIDEO 2 IN

RESET

ENTER

CENTER/SIZE

RGB AUDIO

1 Remote sensor 2 LAMP indicator (pages 24, 26) 3 STANDBY indicator (pages 12, 26) 4 CENTER/SIZE button (page 16) 5 ◊/√/ı/∫ buttons (page 16) 6 VIDEO 2 IN jacks (page 10) 7 RGB 2 IN connector (pages 7, 8)

Identifying the parts

With the front panel attached

With the front panel removed

Front panel

Air filter part (page 23)

Lamp part (page 24)

8 u (power) indicator (pages 12, 26) 9 Power switch (page 12) !º VOLUME +/– buttons (page 12) !¡ MENU button (page 11) !™ ENTER button (page 11) !£ INPUT SELECT button (page 12) !¢ RESET button (pages 16, 17)

This section briefly describes the buttons and controls on the monitor and on the remote control. For more information, refer to the pages next to each description.

Projection monitor — Front

-EN

Additional Information

RESET

CENTER/ SIZE

VOL

ENTER

VIDEO

MUTING

DISPLAY

POWER

RGB WIDE

1 DISPLAY button (page 13) 2 MUTING button (page 13) 3 VIDEO button (page 12) 4 CENTER/SIZE button (page 16) 5 VOL (volume) +/– buttons (page 12) 6 POWER button (page 12) 7 WIDE button (pages 13, 15) 8 RGB button (page 12) 9 V/v/B/b buttons (pages 11, 16) !º MENU button (page 11) !¡ ENTER button (page 11)

Remote control

– 17 –

SECTION 2

Rear cover

Twelve screws (+BVTP 4 x 16)

Chassis assy

Two screws (+BVTP 4 x 16)

Five screws (+BVTP 3 x 12)

U bracket

Two claws

U board

Two claws

DISASSEMBLY

2-1. REAR COVER REMOVAL 2-3. SERVICE POSITION

– 18 –

2-4. U BOARD REMOVAL2-2. CHASSIS ASSY REMOVAL

2-5. POWER BLOCK AND K BOARD REMOVAL 2-6. FILTER REMOVAL

Power block

Terminal

Two printed circuit board holders

K board

Two printed circuit board holders

Two screws (+BVTP 4 x 16)

Two screws (+BVTP 3 x 12)

Filter

Front panel (L)

Filter (Reserve)

– 19 –

2-7. LAMP REMOVAL 2-9-1. SCREEN FRAME REMOVAL [W7000]

Lamp door

Screw (Ornamental screw B)

Front panel (R)

Lamp

Two screws (Hexagon socket bolt 4 x 12)

Two screws (+BVTP 4 x 16)

Screen frame

Eight screws (+BVTP 4 x 16)

Two screws (+BVTP 3 x 12)

HB board

Eight screws (+BVTP 4 x 16)

Front cover

HA board

Six screws (+BVTP 3 x 12)

Sixteen screws (+BVTP 4 x 16)

Screen frame

Two screws (+BVTP 4 x 16)

– 20 –

2-9-2. SCREEN FRAME REMOVAL [W9000]2-8. HA AND HB BOARDS REMOVAL

2-10-1. C BOARD REMOVAL 2-11.OPTICAL UNIT REMOVAL

Screen mirror block

Six screws (+BVTP 4 x 16)

Four printed circuit board holders

Four screws (+BVTP 3 x 12)

C cover

C board

CN5003

CN5001

CN5002

C board

Extension cable

Optical shield

Three screws (+BVTP 4 x 16)

Optical unit

Three screws (+BVTP 4 x 16)

Lamp base

– 21 –

2-10-2. EXTENSION CABLE (C BOARD)

SECTION 3

Item No. up

Item No. down

Write standard values

Press !™ successively.

Read memory

Write in memory

Press !™ successively.

Item feed

Execute reading/writing

Data down

Data up

Quit SERVICE mode

CIRCUIT ADJUSTMENTS

KL-W7000/W9000

RM-Y980

ELECTRICAL ADJUSTMENT IN SERVICE MODE

The SERVICE mode cannot be entered with the remote commander RM-Y980 attached to this set. Use the commander of other TV set.

Adjustment in SERVICE mode

– 22 –

If memory IC 1103 were replaced

Write “standard values”

Adjust all items

Write in memory

Enter SERVICE Mode

Replace board

A board

Release SERVICE mode

If repair concerning picture quality was executed

Replace LCD

Adjust registration

W/B, screen position

Function of commander in SERVICE mode

* Example of SERVICE mode using the commander of other TV set

1 3

2 4 5 6 7 8 9

11 12

1513

Screen in SERVICE mode

Memory reading status

Item No.

Data

Note: • Write data in the memory each time when one item was adjusted.

• Adjusted data are not saved if the power is turned off before they are written in the memory.

Item (register name)

CXZ2011 0 0 0 4 4 G

G: Memory reading normal

NG: Memory reading failed

BASIC ADJUSTMENT IN SERVICE MODE

1. To enter SERVICE mode

1) Turn the POWER switch on the TV set “ON”, then make it in standby status with the remote commander.

2) Operate the remote commander as follows:

Screen display

CH “5”

Volume “+” side

POWER “ON” (remote commander)

2. To read the memory

1) Enter SERVICE mode.

– 23 –

2) Press 10 n 12 buttons on the remote commander, and the adjusted values and set values of all items written in the memory are read out.

Note: If the memory IC was replaced, do not read the memory before writing standard values.

3. Adjustment of screen

1) Select the item No. to be adjusted using 1 and 4 buttons on the remote commander.

2) Adjust with 3 and 6 buttons so as to satisfy the picture quality and the set values.

6. To write +standard values+

1) Enter SERVICE mode.

2) Press 8 button, and green +STANDARD WRITE+ is displayed at the upper right of screen. Successively, press 12 button while this characters are displayed (within about 3 seconds). Green characters change to red +STANDARD WRITE+, then the screen becomes blank, and after about 5 seconds, the RGB 1 is selected and the operation stops. At this time, green +G+ is displayed. When +standard values+ writing is executed, the standard data in the microprocessor on the selected channel are written in the memory. Thus, the initialization is made. Note: Writing of +standard values+ must be executed initially, only if the memory IC

2008 and 2009 were replaced.

4. To write data in the memory

• After adjustment, press “MUTING” 12 buttons to write data in the memory.

Press 12 button while green “WRITE” is displayed on the screen (within about 3 seconds).

Color of WRITE characters on screen

When MUTING button ON ... .............. Green

When 12 button ON .............................. Red

5. To release SERVICE mode

• Turn off the POWER switch on TV set and again turn it on. As a result, the SERVICE

mode display is cleared and normal TV mode is resumed.

• Or, turn off the POWER switch from the remote commander and again turn on the

POWER switch on the remote commander in the standby status. As a result, the SERVICE mode display is cleared and normal TV mode is resumed.

KL-W7000/W9000

RM-Y980

SERVICE LIST

CXA2011Q

Item Display Register Name Range Stndard Values Typical Standard Values

0 DLVL DRIVE LEVEL 0-63 44 44 2 kinds, RGB 3ch gain control 1 SW2 SW2 0,1 0 0 1 kind 2 SW1 SW1 0,1 0 0 1 kind 3 SW0 SW0 0,1 0 0 1 kind 4 SBOF SUB BRI OFFSET 0-63 23 43 2 kinds. Offset of VIDEO/RGB SUB

5 RDOF R DRIVE OFFSET 0-63 31 31 2 kinds. VIDEO/RGB R DRIVE 6 GDOF G DRIVE OFFSET 0-63 31 31 2 kinds. VIDEO/RGB G DRIVE 7 BDOF B DRIVE OFFSET 0-63 31 31 2 kinds. VIDEO/RGB B DRIVE 8 RDMD R DRIVE OFFSET 0-63 32 32 1 kind. Offset of R color temp.

9 GDMD G DRIVE OFFSET 0-63 31 31 1 kind. Offset of G color temp.

10 BDMD B DRIVE OFFSET 0-63 28 28 1 kind. Offset of B color temp.

11 RDLO R DRIVE OFFSET 0-63 34 34 1 kind. Offset of R color temp. “low”

12 GDLD G DRIVE OFFSET 0-63 31 31 1 kind. Offset of G color temp. “low”

– 24 –

13 BDLO B DRIVE OFFSET 0-63 24 24 1 kind. Offset of B color temp. “low”

(color temp. “middle”) “middle” (center value 31)

(color temp. “low”) (center value 31)

VIDEO RGB

BRIGHT 0=–31, · · , 63=+31

BIAS3 (CXA1315)

Item Display Register Name Range Standard Values Typical Standard Values

0 RBS RL_Bias 0-255 0 (VIDEO) 0 (RGB) RL Bias (2 systems of VIDEO, RGB) 1 BLBS RL_Bias 0-255 0 (VIDEO) 0 (RGB) BL Bias (2 systems of VIDEO, RGB) 2 RHBS RL_Bias 0-255 255 (VIDEO) 255 (RGB) RH Bias (2 systems of VIDEO, RGB) 3 BHBS BH_Bias 0-255 255 (VIDEO) 255 (RGB) BH Bias (2 systems of VIDEO, RGB) 4 RLBM RL_Bias off set MID 0-255 131 RL Bias offfset value of color temp.

5 BLBM BL_Bias off set MID 0-255 121 BL Bias offfset value of color temp.

6 RHBM RH_Bias off set MID 0-255 127 RH Bias offfset value of color temp.

7 BHBM BH_Bias off set MID 0-255 127 BH Bias offfset value of color temp.

8 RLBM RL_Bias off set LOW 0-255 136 RL Bias offfset value of color temp.

9 BLBL BL_Bias off set LOW 0-255 115 BL Bias offfset value of color temp.

10 RHBM RH_Bias off set LOW 0-255 127 RH Bias offfset value of color temp.

11 BHBL BH_Bias off set LOW 0-255 127 BH Bias offfset value of color temp.

12 SLSH Sample Phase 0-7

3 (VIDEO 4:3), 3 (RGB 16: 9), 4 (VIDEO 16:9) 4 (RGB 16: 9) (NORMAL, FULL)

“middle” (center value 31)

“low” (center value 31)

“low” (center value 31) 4 kinds of SLSH (VIDEO, RGB) ×

KL-W7000/W9000

RM-Y980

WB (CXA1315)

Item Display Register Name Range Standard Values Typical Standard Values

0 RCOI Red Cut Off 0-255 124 (VIDEO) 124 (RGB) 2 kinds : Red white

balance (VIDEO, RGB)

1 RCOI Green Cut Off 0-255 124 (VIDEO) 124 (RGB) 2 kinds : Green white balance

(GCO center) 2 BCOI Blue Cut Off 0-255 124 (VIDEO) 124 (RGB) 2 kinds : Blue white balance 3 RCOM Red Cut Off OFFSET 0-255 132 Red W/B of color temp.

(color temp. “middle”) “middle” (center value 31)

4 GCOM Green Cut Off OFFSET 0-255 127 Green W/B of color temp.

(color temp. “middle”) “middle” (center value 31)

5 BCOM Blue Cut Off OFFSET 0-255 123 Blue W/B of color temp.

(color temp. “middle”) “middle” (center value 31)

6 RCOL Red Cut Off OFFSET 0-255 138 Red W/B of color temp. “low”

(color temp. “low”) (center value 31)

7 RCOL Green Cut Off OFFSET 0-255 127 Green W/B of color temp.

(color temp. “low”) “low” (center value 31)

8 BCOL Blue Cut Off OFFSET 0-255 118 Blue W/B of color temp.

(color temp. “low”) “low” (center value 31)

A_OUT (NVM A2 DATA)

Item Display Register Name Range Standard Values Typical Standard Values

0 RDON NTSC RDOF 0-63 31 NVM A2 Data of address 00 1 GDON NTSC GDOF 0-63 31 Data of address 01 2 BDON NTSC BDOF 0-63 31 Data of address 02 3 RCON NTSC RCOI 0-255 124 Data of address 03 4 GCON NTSC GCOI 0-255 124 Data of address 04 5 BCON NTSC BCOI 0-255 31 Data of address 05 6 RDOH HD RDOF 0-63 31 Data of address 06 7 GDON HD GDOF 0-63 31 Data of address 07 8 BDON HD BDOF 0-63 31 Data of address 08 9 RCON HD RCOI 0-255 124 Data of address 0B 10 GCOH HD GCOI 0-255 124 Data of address 0A 11BCOH HD BCOI 0-255 124 Data of address 09

– 25 –

CXA1839

Item Display Register Name Range

0 SHUE SUB-HUE 0-15 8 8 2 kinds (VIDEO, RGB) 1 SBRT SUB-BRT 0-15 8 8 2 kinds (VIDEO, RGB) 2 R-Y/R R-Y/R 0-15 0 0 2 kinds (VIDEO, RGB) 3 R-Y/B R-Y/B 0-15 8 15 2 kinds (VIDEO, RGB) 4 G-Y/R G-Y/R 0-15 15 15 2 kinds (VIDEO, RGB) 5 G-Y/B G-Y/B 0-15 8 0 2 kinds (VIDEO, RGB) 6 SPC2 SUB-CON2 0-15 8 8 2 kinds (VIDEO, RGB) 7 SCL2 SUB-COL2 0-15 8 8 2 kinds (VIDEO, RGB) 8 RGB2 RGB2_LEVEL 0-15 11 1 kind 9 SSHP SUB-SHP 0-3 3/3 1 4 kinds (VIDEO, RGB) × (NORMAL, WIDE) 10 SHPF SHP-F0 0-3 2/2 1 4 kinds (VIDEO, RGB) × (NORMAL, WIDE) 11 PREL PRE_OVER 0-3 3/3 3 4 kinds (VIDEO, RGB) × (NORMAL, WIDE) 12 Y-DC DC-TRAN 0-15 0 0 2 kinds, transmission rate of DC. (VIDEO,

13 DPIX DYNAMIC-PIC 0-3 0 0 2 kinds, Auto pedestal. (VIDEO, RGB) 14 CECL CEC_LEVEL 0-3 3 1 2 kinds, Chroma edge clear. (VIDEO, RGB) 15 RHUE RGB HUE 0-63 – 31 1 kind, Hue adjustment at RGB input. 16 RCOL RGB COLOR 0-63 – 31 1 kind, Color adjustment at RGB input. 17 RSHP 18 SHPP

19 SHPS SHARP 0-63 31 25 1 kind, AI mode, STANDARD sharpness 20 SHPM SHARP MOVIE 0-63 27 31 1 kind, AI mode, MOVIE sharpness value

RGB SHAPNESS SHARP PRESEN.

STANDARD value

Standard Values

VIDEO RGB

0-63 – 25 1 kind, Sharpness adjustment at RGB input. 0-63 35 25 1 kind, AI mode, PRESENTATION

Typical Standard Values

RGB)

sharpness value

3C (3-Dimensional Com µPD6487)

Item Display Register Name Range Standard Values Typical Standard Values

0 MS MSI, MSO 0-3 0 00 00 : Normal, 01 : 2D, 10 : 3D 1 BPFS BPFS 0-1 0 0 0 : Normal,

2 YDLL YDELAYL 0-7 2/2 1 Kind Output delay designation 3 HRD HRD8-1 0-255 21 21 (2Ah) 21 (2A) : B lock only 4 DYCO DYCOR 0-15 5/5 1 Kind DY detection coaring level 5 DYGA DYGAIN 0-15 8/8 1 Kind DY detection gain 6 DCCO DCCOR 0-15 5/5 1 Kind DC detection coaring level 7 DCGA DCGAIN 0-15 6/6 1 Kind DC detection gain 8 VTR VTR1, VTR0 0-3 0 00 00 : Normal, 01 : Standard,

9 VTRR VTRR 0-31 7/7 1 Kind VTR detection level 10 LDS LDSOFF 0-1 0 0 LD still detect selection 11 HSDR HSDR 0-31 7/7 1 Kind Sync detection level 12 BSDR BSDR 0-31 7 7 Sync detection level 13 WSCO WSCOR 0-7 7/7 1 Kind Weak field detection coaring level 14 WSD1 WSDR1 0-15 15/15 1 Kind Weak field detection level 1 15 WSD2 WSDR2 0-15 15/15 1 Kind Weak field detection level 2 16 VAPG VAPGAIN 0-7 4/4 7/7 0/0 2 Kinds V aperture gain *1 17 VAPI VAPINV 0-31 12/12 20/20 12/12 2 Kinds V aperture inversion point *1

Others

PRESENTATION

MOVIE

1 : Band-pass YC separation

10 : Non-Standard

*1 : 6 kinds of (STANDARD/AV MEMORY, PRESENTATION, MOVIE) × (NORMAL/FULL,

OTHERS)

CXD2052 (Digital Chroma Decoder)

Item Display Register Name Range

0 ACR ACR 0-255 53 35h 1 AKO AKO 0-255 20 24h 2 AKF AKF 0-255 50 32h 3 PKO PKO 0-255 252 FCh 4 PKF PKF 0-255 16 10h 5 OFS OFS 0-255 128 80h 6 BPF1 BPF1 0-1 0(C) 1(S) 2 kinds of S/COMP 7 BPF2 BPF2 0-1 0(C) 0(S) 2 kinds of S/COMP 8 TRAP TRAP 0-1 0 0 9 HPF HFP 0-7 10 FCP FCOP 0-1 0 0 11 DCON DCON 0-1 0 0 12 F2CC F2CCH 0-1 0 0 13 EDTV EDTV 0-1 1 1 14 KILL KILL 0-1 0 0 15 APCO APCOF 0-1 0 0 16 XFH XFH 0-1 0 17 XFH XFH 0-1 0(C) 0(S) 2 kinds of S/COMP 18 TA TA 0-31 16 1ch 19 TB TB 0-63 38(C) 58(C) 2 kinds of S/COMP 20 TO TO 0-63 42(C) 55(C) 2 kinds of S/COMP 21 TE TB 0-63 23(C) 55(S) 2 kinds of S/COMP

Standard Values

VIDEO RGB

4(VIDEO)

Typical Standard Values

2 kinds of VIDEO/RGB

1C (3-Dimensional Com µPD6486)

Item Display Register Name Range Standard Values Typical Standard Values

Others Presen. Movie 0 MS MS1, MS0 0-3 0 1 BPFS BPFS 0-1 0 2 YDLL YDELAYL 0-7 2/2 3 HRD HRD8-1 0-256 21 4 DYCO DYCOR 0-15 5/5 5 DYGA DYGAIN 0-15 8/8 6 DCCO DCCOR 0-15 5/5 7 DCGA DCGAIN 0-15 6/6 8 VTR VTR1, VTR0 0-3 0 9 VTRR VTRR 0-31 7/7 10 LDS LDSOFF 0-1 0 11 HSDR HSDR 0-31 7/7 12 BSDR BSDR 0-31 7 13 WSCO WSCOR 0-7 7/7 14 WSD1 WSDR1 0-15 15/15 15 WSD2 WSDR2 0-15 15/15 16 VAPG VAPGAIN 0-7 4/4 7/7 0/0 NORMAL, FULL/OTHERS 17 VAPI VAPINV 0-31 12/12 20/20 12/12 NORMAL, FULL/OTHERS

KL-W7000/W9000

RM-Y980

KL-W7000/W9000

RM-Y980

MID2 (CXD2072Q VIDEO )

Item Register Range Standard Values Typical Standard Values Display Name

0 HSIZ HSIZEA 0-255 88 Every input signal: H size adj. (NTSC) 1 VGAH VGAHS 0-127 0 Every input signal polarity + Wide screen: H

2 HPOS HPOSIA 0-255 36 Every input signal: H position adj. (READ) 3 VSIZ VSIZEA 0-255 F0 38 0 0 Every input signal polarity + Wide screen: V

4 VPOS VPOSIA 0-255 28 Every input signal: V position adj. (READ) 5 HPHS HPHASA 0-255 44 Every input signal polarity + Wide screen: H

6 VPHS VPHASA 0-255 0A 17 17 0F Every input signal polarity + Wide screen: V

WONA 8 OSCA OSCA 0-1 1 Every input signal: Masking range switching 9 DLYA DELAYA 0-7 3 Every input signal: Color difference delay adj.

HVSW 11YSDY YSDY 0-7 2 Every input signal: YS delay adj. 12DLY DELAY 0-7 4 Every input signal: Color difference delay

13HBLK HBLK 0-255 89 Every input signal: H blanking adj. 14VBLK VBLK 0-255 1F Every input signal: V blanking adj. 15IPVA IPVA 0-1 0 Every input signal: Vertical linear interpolation

– 26 –

16OFST OFFSET 0-255 0 17VSCA VSCA 0-1 0 1 1 1 Every input signal: A ch vertical size 18OSVA OSVA 0-1 1 Every input signal: A ch vertical offset 19PLL1 PLL1 0-7 0 Every input signal: PLL 1 frequency dividing

20YUV YUV 0-3 0 Every input signal: YUV signal sampling ratio 21REF REF 0-7 0 Every input signal: V size reference value 22CLPD CLPDA 0-255 28 Every input signal: A ch clamp position adj. 23HPH0 bit 0 of HPHASA 0-1 0 Every input signal polarity + Wide screen: H

24HPH0 bit 0 of VPHASA 0-1 0 Every input signal polarity + Wide screen: V

25HCOF H CENT OF. 0-63 – Every input signal: H center offset 26H0OF bit 0 of H CENT OF.0-1 – Every input signal: H center offset (bit 0) 27VCOF V CENT OF. 0-63 – Every input signal: V center offset 28V0OF 29HSOF H SIZE OF. 0-63 – Every input signal: H size offset 30VSOF V SIZE OF. 0-255 – Every input signal: V size offset 31HPR3 HPOSIA REF3 0-255 – HPOSIA value when REF=3 of user preset signal 32HPR4 HPOSIA REF4 0-255 – HPOSIA value when REF=4 of user preset signal 33HPR5 HPOSIA REF5 0-255 – HPOSIA value when REF=5 of user preset signal 34SCOF V SCROLL OF. 0-31 – 0A 0A 0A Every wide screen: V scroll offset 35S0OF 36SCRS V SCROLL 0-63 – 17 17 0F Every wide screen: V scroll standard value

37S0RS

WONA 0-1 0 Every input signal: MOVIE/STILL switching

HVSW 0-3 2 Every input signal: Output Sync signal switching

bit 0 of V CENT OF.

bit 0 of V SCROLL OF.

Standard value bit 0 of V SCROLL0-1 – 0 0 0 Every wide screen: V scroll standard value (bit 0)

Standard value

NORMAL/FULL

0-1 – Every input signal: V center offset (bit 0)

0-1 – 0 0 0 Every wide screen: V scroll offset (bit 0)

ZOOM SUBTITLE

WIDEZOOM

size adj. (RGB)

size adj.

posi adj. (WRITE)

(INPUT)

adj. (OUTPUT)

Every input signal: Linear interpolation offset setting

ratio setting

posi adj. (WRITE)

MID2 (CXD2072Q RGB (1) )

Item Register Range Standard Values Typical Standard Values Display Name VGAT350 VGAG W-VGA VGA72 VGA75

0 HSIZ HSIZEA 0-255 A0 Every input signal: H size adj. (NTSC) 1 VGAH VGAHS 0-127 2F 30 2E 2F 2B Every input signal polarity + Wide screen: H

2 HPOS HPOSIA 0-255 2E 2E 2D 2E 2A Every input signal: H position adj. (READ) 3 VSIZ VSIZEA 0-255 3 Every input signal polarity + Wide screen: V

4 VPOS VPOSIA 0-255 38 1E 1E 1E 1E Every input signal: V position adj. (READ) 5 HPHS HPHASA 0-255 42 42 43 4E 52 Every input signal polarity + Wide screen: H

6 VPHS VPHASA 0-255 3 8 8 6 0 Every input signal polarity + Wide screen: V

WONA 8 OSCA OSCA 0-1 1 Every input signal: Masking range switching 9 DLYA DELAYA 0-7 3 Every input signal: Color difference delay adj.

10HVSW HVSW 0-3 1 Every input signal: Output Sync signal switching 11YSDY YSDY 0-7 1 Every input signal: YS delay adj. 12DLY DELAY 0-7 4 Every input signal: Color difference delay

13HBLK HBLK 0-255 A0 Every input signal: H blanking adj. 14VBLK VBLK 0-255 0A 30 30 30 30 Every input signal: V blanking adj. 15IPVA IPVA 0-1 0 Every input signal: Vertical linear interpolation 16OFST OFFSET 0-255 0 17VSCA VSCA 0-1 1 Every input signal: A ch vertical siz 18OSVA OSVA 0-1 1 Every input signal: A ch vertical offset 19PLL1 PLL1 0-7 4 4 4 5 5 Every input signal: PLL 1 frequency dividing

20YUV YUV 0-3 1 Every input signal: YUV signal sampling ratio 21REF REF 0-7 5 Every input signal: V size reference value 22CLPD CLPDA 0-255 6A Every input signal: A ch clamp position adj. 23HPH0 bit 0 of HPHASA 0-1 0 Every input signal polarity + Wide screen: H

24VPH0 bit 0 of VPHASA 0-1 0 Every input signal polarity + Wide screen:

25HCOF H CENT OF. 0-63 26 Every input signal: H center offse 26H0OF 27VCOF V CENT OF. 0-63 0 Every input signal: V center offset 28V0OF bit 0 of V CENT OF. 29HSOF H SIZE OF. 0-63 1F 20 20 1F 1B Every input signal: H size offset 30VSOF V SIZE OF. 0-255 EB Every input signal: V size offset 31HPR3 HPOSIA REF3 0-255 28 HPOSIA value when REF=3 of user preset signal 32HPR4 HPOSIA REF4 0-255 25 HPOSIA value when REF=4 of user preset signal 33HPR5 HPOSIA REF5 0-255 28 HPOSIA value when REF=5 of user preset signal 34SCOF V SCROLL OF. 0-31 – Every wide screen: V scroll offset 35S0OF 36SCRS V SCROLL 0-63 – Every wide screen: V scroll standard value

37S0RS

WONA 0-1 0 Every input signal: MOVIE/STILL switching

bit 0 of H CENT OF.

bit 0 of V SCROLL OF.

Standard value bit 0 of V SCROLL

Standard value

0-1 0 Every input signal: H center offset (bit 0

0-1 0 Every input signal: V center offset (bit 0)

0-1 – Every wide screen: V scroll offset (bit 0)

0-1 – Every wide screen: V scroll standard value(bit 0)

size adj. (RGB)

size adj.

posi adj. (WRITE)

(INPUT)

adj. (OUTPUT)

Every input signal: Linear interpolation offset setting

ratio setting

posi adj. (WRITE)

MID2 (CXD2072Q RGB (2) )

Item Register Range Standard Values Typical Standard Values Display Name VGA85 SVGA56 SVGA60 W-SVGA SVGA72

0 HSIZ HSIZEA 0-255 A0 Every input signal: H size adj. (NTSC) 1 VGAH VGAHS 0-127 2F 26 1A 18 1F Every input signal polarity + Wide screen: H

2 HPOS HPOSIA 0-255 2E 2A 27 27 28 Every input signal: H position adj. (READ) 3 VSIZ VSIZEA 0-255 3 F0 F0 F0 F0 Every input signal polarity + Wide screen: V

4 VPOS VPOSIA 0-255 1D 1F 1F 1F 1F Every input signal: V position adj. (READ) 5 HPHS HPHASA 0-255 3D 45 48 4C 3D Every input signal polarity + Wide screen: H

6 VPHS VPHASA 0-255 4 7 8 8 9 Every input signal polarity + Wide screen: V

7 WONA WONA 0-1 0 Every input signal: MOVIE/STILL switching 8 OSCA OSCA 0-1 1 Every input signal: Masking range switching 9 DLYA DELAYA 0-7 3 Every input signal: Color difference delay

10HVSW HVSW 0-3 1 Every input signal: Output Sync signal switching 11YSDY YSDY 0-7 1 Every input signal: YS delay adj. 12DLY DELAY 0-7 4 Every input signal: Color difference delay

13HBLK HBLK 0-255 A0 Every input signal: H blanking adj. 14VBLK VBLK 0-255 30 Every input signal: V blanking adj. 15IPVA IPVA 0-1 0 Every input signal: Vertical linear interpolation

– 27 –

16OFST OFFSET 0-255 0 17VSCA VSCA 0-1 1 0 0 0 0 Every input signal: A ch vertical size 18OSVA OSVA 0-1 1 Every input signal: A ch vertical offset 19PLL1 PLL1 0-7 5 4 4 4 4 Every input signal: PLL 1 frequency dividing

20YUV YUV 0-3 1 Every input signal: YUV signal sampling ratio 21REF REF 0-7 5 2 2 2 2 Every input signal: V size reference value 22CLPD CLPDA 0-255 6A Every input signal: A ch clamp position adj. 23HPH0 bit 0 of HPHASA 0-1 1 1 0 0 0 Every input signal polarity + Wide screen: H

24HPH0 bit 0 of VPHASA 0-1 0 0 1 1 1 Every input signal polarity + Wide screen: V

25HCOF H CENT OF. 0-63 26 Every input signal: H center offset 26H0OF

bit 0 of H CENT OF. 27VCOF V CENT OF. 0-63 0 Every input signal: V center offset 28V0OF bit 0 of V CENT OF. 29HSOF H SIZE OF. 0-63 1F 16 0A 0A 0F Every input signal: H size offset 30VSOF V SIZE OF. 0-255 EB E7 E7 E7 E7 Every input signal: V size offset 31HPR3 HPOSIA REF3 0-255 28 HPOSIA value when REF=3 of user preset signal 32HPR4 HPOSIA REF4 0-255 25 HPOSIA value when REF=4 of user preset signal 33HPR5 HPOSIA REF5 0-255 28 HPOSIA value when REF=5 of user preset signal 34SCOF V SCROLL OF. 0-31 – Every wide screen: V scroll offset 35S0OF

bit 0 of V SCROLL OF.

36SCRS V SCROLL 0-63 – Every wide screen: V scroll standard value

Standard value

37S0RS

bit 0 of V SCROLL Standard value

0-1 1 1 0 0 0 Every input signal: H center offset (bit 0)

0-1 0 0 1 1 1 Every input signal: V center offset (bit 0)

0-1 – Every wide screen: V scroll offset (bit 0)

0-1 – Every wide screen: V scroll standard value(bit 0)

size adj. (RGB)

size adj.

posi adj. (WRITE)

adj. (INPUT)

adj. (OUTPUT)

Every input signal: Linear interpolation offset setting

ratio setting

posi adj. (WRITE)

MID2 (CXD2072Q RGB (3) )

Item Register Range Standard Values Typical Standard Values Display Name SVGA75 XGA60 W-XGA MAC13 MAC16

0 HSIZ HSIZEA 0-255 A0 Every input signal: H size adj. (NTSC) 1 VGAH VGAHS 0-127 1A 1D 1C 2F 9 Every input signal polarity + Wide screen: H

2 HPOS HPOSIA 0-255 28 26 26 2E 24 Every input signal: H position adj. (READ) 3 VSIZ VSIZEA 0-255 F0 F0 F0 3 F0 Every input signal polarity + Wide screen: V

4 VPOS VPOSIA 0-255 1F 1F 1F 1E 1F Every input signal: V position adj. (READ) 5 HPHS HPHASA 0-255 51 4C 4C 4A 59 Every input signal polarity + Wide screen: H

6 VPHS VPHASA 0-255 7 8 8 0B 0F Every input signal polarity + Wide screen: V

7 WONA WONA 0-1 0 Every input signal: MOVIE/STILL switching 8 OSCA OSCA 0-1 1 Every input signal: Masking range switching 9 DLYA DELAYA 0-7 3 Every input signal: Color difference delay

10HVSW HVSW 0-3 1 Every input signal: Output Sync signal switching 11YSDY YSDY 0-7 1 Every input signal: YS delay adj. 12DLY DELAY 0-7 4 Every input signal: Color difference delay

13HBLK HBLK 0-255 A0 Every input signal: H blanking adj. 14VBLK VBLK 0-255 30 Every input signal: V blanking adj. 15IPVA IPVA 0-1 0 Every input signal: Vertical linear interpolation 16OFST OFFSET 0-255 0 17VSCA VSCA 0-1 0 0 0 1 0 Every input signal: A ch vertical size 18OSVA OSVA 0-1 1 Every input signal: A ch vertical offset 19PLL1 PLL1 0-7 4 4 4 6 4 Every input signal: PLL 1 frequency dividing

20YUV YUV 0-3 1 Every input signal: YUV signal sampling ratio 21REF REF 0-7 2 4 4 5 3 Every input signal: V size reference value 22CLPD CLPDA 0-255 6A 6A 6A 40 6A Every input signal: A ch clamp position adj. 23HPH0 bit 0 of HPHASA 0-1 1 0 0 0 1 Every input signal polarity + Wide screen: H

24VPH0 bit 0 of VPHASA 0-1 0 1 1 1 0 Every input signal polarity + Wide screen: V

25HCOF H CENT OF. 0-63 26 26 26 26 2E Every input signal: H center offset 26H0OF

bit 0 of H CENT OF. 27VCOF V CENT OF. 0-63 0 Every input signal: V center offset 28V0OF

bit 0 of V CENT OF. 29HSOF H SIZE OF. 0-63 0A 0D 0D 1F 0 Every input signal: H size offset 30VSOF V SIZE OF. 0-255 E7 E7 E7 EB E7 Every input signal: V size offset 31HPR3 HPOSIA REF3 0-255 28 HPOSIA value when REF=3 of user preset signal 32HPR4 HPOSIA REF4 0-255 25 HPOSIA value when REF=4 of user preset signal 33HPR5 HPOSIA REF5 0-255 28 HPOSIA value when REF=5 of user preset signal 34SCOF V SCROLL OF. 0-31 – Every wide screen: V scroll offset 35S0OF

bit 0 of V SCROLL OF.

36SCRS V SCROLL 0-63 – Every wide screen: V scroll standard value

Standard value

37S0RS

bit 0 of V SCROLL Standard value

0-1 1 0 0 0 1 Every input signal: H center offset (bit 0)

0-1 0 1 1 1 0 Every input signal: V center offset (bit 0)

0-1 – Every wide screen: V scroll offset (bit 0)

0-1 – Every wide screen: V scroll standard value(bit 0)

size adj. (RGB)

size adj.

posi adj. (WRITE)

adj. (INPUT)

adj. (OUTPUT)

Every input signal: Linear interpolation offset setting

ratio setting

posi adj. (WRITE)

KL-W7000/W9000

RM-Y980

+ 64 hidden pages