Sony KL-40WA1K User Manual
R
3-861-211-41 (1)
KL-40WA1K
KL-40W A1K
Getting Started
Operating Instructions
UvedenÌ do provozu
Funkce
Przed rozpoczÍciem
Instrukcja obs≥ugi
A kÈsz¸lÈk
¸zembehelyezÈse
Hasn·lati ⁄tmutatÛ
燘‡ÎÓ
GB
GB
CZ
CZ
PL
PL
H
H
BG
LCD Projection TV
аМТЪ ЫНˆЛЛ Б‡
ВНТФОУ‡Ъ‡ˆЛfl
иУ‰„УЪУ‚Н‡ Н
˝НТФОЫ‡Ъ‡ˆЛЛ
аМТЪ ЫНˆЛfl ФУ
˝НТФОЫ‡Ъ‡ˆЛЛ
àÌcÚpyÍáËÓ Ôo
íÍcÔÎyaÚaáËË
èoÀÖoÚoÇÍa Í
íÍcÔÎyaÚaáËË
BG
RF
RF
RF
RF
© 1997 by Sony Corporation Printed in Spain
WARNING
To prevent fire or shock hazard, do not expose the unit to
rain or moisture.
Dangerously high voltages are present inside the set. Do
not open the cabinet. Refer servicing to qualified
personnel only.
Safety Information
All TVs operate on extremely high voltages. To prevent
fire or electric shock, please follow the safety procedures
below. For your protection, refer all servicing to qualified
personnel only.
For general safety:
• Do not expose the TV to rain or moisture.
• Do not open the rear cover.
For safe operations:
• Do not operate the TV on any other voltages, but 220–
240 V AC.
• Do not operate the TV if any liquid or solid object falls in it
- have it checked immediately.
• Do not keep the set plugged in if you are not going to use
it for several days.
• Do not pull on the power cord to disconnect the TV. Pull it
out by the plug.
• Do not place anything on the surface of the front panel
cover when you open it.
Important Information
Please read the following information on using and
maintaining the TV, for optimum viewing quality.
Picture Quality
• Avoid touching the screen, and take care not to scratch
the surface with hard objects.
Illumination
To obtain a clear picture, do not expose the screen to
direct illumination or direct sunlight. If possible, use spot
lighting directed down from the ceiling.
Installation
• To prevent over heating of the set, do not block the
ventilation openings.
• Do not install the TV in a hot or humid place, or in a place
subject to direct sunlight, excessive dust or mechanical
vibration.
• After transporting the TV directly from a cold to a warm
location, or if the room temperature has changed
suddenly, pictures may be blurred or show poor colour
over portions of the picture. This is because moisture has
condensed on the mirrors or lenses inside the TV. Let the
moisture evaporate before using the TV.
Maintenance
• Save the original shipping carton and packing material to
use if you ever have to ship your TV. For maximum
protection, repack your TV as it was originally packed at
the factory.
• To keep the cabinet looking brand-new, periodically clean
it with a soft cloth. Stubborn stains may be removed with a
cloth slightly dampened with a mild detergent solution.
Never use strong solvents such as thinner or benzene, or
abrasive cleaners since these will damage the cabinet. As
a safety precaution, unplug the TV before cleaning it.
• To remove dust from the front of the screen, unplug the
TV and wipe gently with a soft cloth lightly dampened with
water or a mild detergent solution, using vertical strokes
only. Then wipe it with a dry, soft cloth. Never use
solvents or thinners for cleaning purposes.
• If the picture turns dark after the TV has been in use for a
long period of time, it may be necessary to clean the
inside of the TV. Consult qualified service personnel for
this.
2
Contents
Overview ................................................................................... 4
Getting Started ...............................................................
Step 1 Preparation..................................................................... 6
Check the supplied accessories ...................................... 6
Insert the batteries into the Remote Commander ............. 6
Connect the aerial........................................................... 6
Step 2 Tuning in to TV Stations .................................................. 7
Choosing the Menu Language and the Country ............... 7
Presetting Channels Automatically .................................. 8
Additional Presetting Functions .................................................. 9
Presetting Channels Manually......................................... 9
Sorting Programme Positions........................................ 10
Using “Further Programme Preset” ............................... 11
Skipping Programme Positions ..................................... 12
Captioning a Station Name ........................................... 12
Using Parental Lock...................................................... 13
Tuning in a Channel Temporarily................................... 13
Operating Instructions.................................................
Watching the TV....................................................................... 14
Switching the TV on and off ........................................... 14
Selecting TV Programmes ............................................ 14
Adjusting the Volume .................................................... 14
Operating the TV Using the Buttons on the TV............... 14
Watching Teletext or Video Input................................... 15
More Convenient Functions .......................................... 15
14
6
Getting Started
Operating Instructions
GB
GB
Adjusting and Setting the TV Using the Menu ........................... 16
Adjusting the Picture and Sound ................................... 16
Using the Sleep Timer................................................... 17
Operating Screen Mode ................................................ 18
Auto 16:9 ...................................................................... 18
Teletext.................................................................................... 19
Direct Access Functions................................................ 19
Using the Teletext Menu ............................................... 21
User Page Bank System ............................................... 22
Connecting and Operating Optional Equipment ........................ 23
Connecting Optional Equipment.................................... 23
Selecting lnput and Output ............................................ 24
Using AV Preset ........................................................... 25
Remote Control of Other Sony Equipment..................... 26
For Your Information ................................................................ 27
Optimum Viewing Area ................................................. 27
Cleaning the Air Filter.................................................... 28
Replacing the Lamp ...................................................... 29
Troubleshooting............................................................ 30
Specifications ............................................................... 30
Warning Indicators........................................................ 31
Stabilizing the Projection TV.......................................... 31
3
Overview
This section briefly describes the buttons and controls on the TV
set and on the Remote Commander. For more information, refer to
the pages given next to each description.
TV set-front
Symbol
u
u
A-m -B
PROGR+/–
. +/–
l
S
3, 3, 3
Name
Main power switch
Standby indicator
Stereo A/B indicators
Lamp indicator
Programme
Volume buttons
Input select buttons
Headphones jack
Input jacks (S video/video/audio)
Refer to page
14
14, 31
17
29, 31
14
14
15
23
24
4
Remote commander
TV
MDP2
3VTR 1
¤
( u)
REC
+
;
…/
´8x
MENU
VIDEO
+
CH
_
?
Ú/;
c
PROGR
0
p Pr
˚
8
;
´/´
a/Å
A
b
≥
¸
TV/Teletext operation
Video operation
TV/Teletext operation
Menu operation
Symbol
MENU
Name
Menu on/off button
Joystick for Menu selection
Press to confirm selection
(OK function)
Video operation
Symbol
VTR1/2/3,
MDP
;; - :: L
J a VIDEO f
CH +/–
Name
Video equipment selector
Video equipment operation
buttons
GB
Refer to page
See below.
See below.
Refer to page
26
26
RM-862
TV/Teletext operation
Symbol
o
TV u
;
f
…/
Ú/
1,2,3,4,5,6,
7,8,9 and 0
÷
C
Á+/–
PROGR +/–
Í
≥
Name
Mute on/off button
TV Standby button
TV power on/TV mode selector
button
Teletext button
Input mode selector/
Teletext: Freezing the subpage
Output mode selector/
Teletext: Reveal button
Number buttons
Double-digit entering button
Direct channel entering button
Volume control button
Programme selectors
Teletext: Page up/page down buttons
Picture adjustment button
Sound adjustment button
On-screen display button
Time display button
“Freeze” button
Button to change Screen Format
Teletext: Favourite pages button
Menu operation
Refer to page
15
14
14
15
15
20
24
20
14
14
9
14
14
20
16
16
15
15
15
15
22
No function on this set
Symbol : , , , ,
For the Menu System
Use the MENU button and the joystick as follows.
1 Press MENU button to switch menu on or off.
MENU
2 Use the joystick as follows:
GREEN: scroll up
RED:
decrease/back to last item
or to last menu
When menu is not
displayed:
Push to red to display the
last menu screen
BLUE: scroll down
The operable functions of the joystick are displayed on the
screen.
YELLOW:
increase/forward
to next item
Joystick: Press at
its neutral position
to confirm selection
or store
5
Getting Started
Step 1 Preparation
2
1
1 Check the supplied accessories
When you’ve taken everything
out of the carton, check that you
have these items:
• RM-862 Remote Commander
• Two IEC designation R6 batteries
• Wrench (1)
• Bracket (2)
2
1
Note: Always remember
to dispose of used
batteries in an
environmentally friendly
way.
2 Insert the batteries into the Remote Commander
Remove the cover.
Check the correct
polarities.
3 Connect the aerial
C
6
Fit an IEC aerial connector attached to 75-ohm coaxial cable (not
supplied) to the ) socket at the rear of the TV.
Step 2 Tuning in to TV Stations
2
1
1 Choosing the Menu Language
GB
MDP2
3VTR 1
¤
0
( u)
p Pr
REC
+
˚
;
…/
8
;
´8x
´/´
a/Å
A
b
≥
MENU
¸
VIDEO
CH
Ú/;
PROGR
RM-862
TV
and the Country
Using this function, you can select the language of the menu
LANGUAGE
screens. Also, you can select the country in which you will use the
TV. In this way, the channels of the selected country will
+
_
?
automatically get the top positions during automatic presetting.
1 Press the power switch u on the TV.
If the standby indicator u on the TV is lit, press ; or a number
OK
Select
button on the Remote Commander.
2 Press MENU on the Remote Commander.
The LANGUAGE menu appears.
3 Push the joystick to blue or green to select the language. Press
the joystick to confirm your selection.
c
The COUNTRY menu appears.
4 Push the joystick to blue or green to select the country in which you
wish to operate the TV. Press the joystick to confirm the selection.
5 Press MENU to restore the normal TV picture.
COUNTRY
A
B
CH
CZ
D
DK
E
F
f
To go back to the
normal TV picture
Press MENU. Normal
TV picture will be
restored after one
minute if menu functions
are not selected.
Note on the Demo
function
If you choose Demo in
the INSTALLATION
menu, you can see a
sequential
demonstration of the
menu functions.
Press MENU to stop the
function.
7
2 Presetting Channels
Automaticall y
Notes
• After presetting the
channels automatically,
you can check which
channels are stored on
which programme
positions.
For details, see
“Displaying the
Programme Table” on
page 15.
• You can sort the
programme positions to
have them appear on
screen in the order you
like. For details, see
“Sorting Programme
Positions” on page 10.
With this function, the TV automatically searches and stores up to
100 channels onto programme positions. If you prefer “Presetting
Channels Manually”, please refer to page 9 in Additional Presetting
Functions.
1 Press MENU.
2 Push the joystick to blue or green to select the symbol
on the
menu screen, then push to yellow.
3 Push the joystick to blue or green to select “Auto Programme”,
then push to yellow.
The AUTO PROGRAMME menu appears.
4 a) All items shown on the menu screen are as wanted: Press the
joystick to select START.
Now the automatic channel presetting starts from programme
position 1.
or
4 b) You wish to change items as shown on the menu screen: Push
the joystick to blue or green. Push to yellow repeatedly until the
desired item is highlighted.
Push the joystick to blue or green to select the following options:
ACI (Automatic Channel Installation, depending on
availability of service in your country)
on: fast channel presetting by special networks using the channel
frequency (e.g. F055)
TV-system and station label
off: ACI is not active, only ITP (Intelligent Tuner Preset)
SYS (TV Broadcast System)
I for U.K.
B/G for Western European Countries
D/K for Eastern European Countries
L for France
PROG (Programme Position)
Presetting automatically starts from position 1.
CH (channel)
C to start presetting with terrestrial channels
S to start presetting with cable channels
Press the joystick as soon as the automatic presetting starts.
PRESET
Auto Programme
Manual Programme Preset
Programme Sorting
Parental Lock
Installation
AUTO PROGRAMME
START
ACI
SYS PROG CH LABEL
B/G 01 C07 SW3on
8
Additional Presetting Functions
2
1
MANUAL
PROGRAMME
PRESET
MDP2
3VTR 1
¤
0
( u)
p Pr
CH
REC
+
˚
;
…/
8
;
´8x
´/´
a/Å
A
b
≥
MENU
¸
RM-862
TV
VIDEO
+
_
Ú/;
c
PROGR
Presetting Channels Manually
Using this function, you can preset channels one by one to
different programme positions. This is also convenient to allocate
programme numbers to video input sources.
1 Press MENU.
PRESET
Auto Programme
Manual Programme Preset
Programme Sorting
Parental Lock
Installation
GB
2 Push the joystick to blue or green to select the symbol on the
menu screen. Push to yellow to confirm the selection.
3 Push to blue or green to select “Manual Programme Preset”. Push
to yellow to confirm the selection.
4 Push to blue or green to select the programme position (PROG) to
which you want to preset a channel. Push to yellow to confirm.
5 Push to blue or green to select the TV broadcast system (SYS)
?
(I for U.K., B/G for western European countries, D/K for eastern
European countries, L for France) or a video input source (EXT).
MANUAL PROGRAMME PRESET
PROG
SYS
CH
B/G
B/G
B/G
B/G
B/G
B/G
B/G
B/G
SEARCH LABEL
C21
off
C34
off
C33
off
C45
off
C02
off
C08
off
C10
off
C12
off
-----
-----
-----
-----
-----
-----
-----
-----
1
2
3
4
5
6
7
8
Push to yellow to confirm.
6 Push to blue or green to select “C” (for terrestrial channels), “S” (for
cable channels) or “F” ( for channel frequency). Push to yellow to
confirm.
There are two options to preset channels manually:
a) You know the channel number or channel frequency.
Please use method “Direct Input”.
or
b) You don’t know the channel number or frequency.
Please use method “Search”.
7 a) Direct Input
For channel numbers, you need to input a two digit number, for the
frequency, a three digit number.
• Push to blue or green to select the first digit of the channel number
or frequency. Push to yellow to confirm.
• Push to blue or green to select the second digit of the number or
frequency. Push to yellow to confirm. In case of the channel
number, the search starts.
• Push to blue or green to select the third digit of the frequency
number. Push to yellow to start the search of the frequency.
• To continue search for another channel: Push to blue or green.
• To store the selected channel: Press the joystick.
• Repeat steps 4 to 7 a) to preset other channels.
7 b ) Search
• Push repeatedly to yellow until a blue and a green arrow appear in
the section SEARCH.
• Push to blue or green to search for the next available channel.
• To continue search for another channel: Push to blue or green.
• To store the selected channel: Press the joystick.
• Repeat steps 4 to 7 b) to preset other channels.
9
PROGRAMME
SORTING
To go back to the
normal TV picture
Press MENU.
Sorting Programme Positions
This function enables you to sort the programme positions to a
preferable order.
1 Press MENU.
2 Push the joystick to blue or green to select the symbol
menu screen. Push to yellow to confirm.
3 Push to blue or green to select “Programme Sorting”. Push to
yellow to confirm.
4 Push to blue or green to select the programme position of the
channel you want to change. Press joystick to confirm.
5 Push to blue or green to select the new programme position.
Press joystick to confirm.
Now the selected channel is changed to the new programme
position.
6 Repeat steps 4 and 5 to sort other programme positions.
on the
PROGRAMME SORTING
PROG
CH LABEL
1
C03
C04
2
C07
3
C09
4
C12
5
C13
6
C14
7
C15
8
Move PR 8 to PR - -
8 BBC1C15
BBC 2
ITV
MBC
-----
-----
-----
-----
BBC 1
10
Loading...