Sony HXC-FB75H User Guide

4-593-326-12 (1)

HD Color Camera

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

HXC-FB75

Overview .............................................................................3

Camera System Components ....................................................3

System Configuration ...............................................................4

Name and Function of Parts..............................................7

Front and Left Side ...................................................................7

Front and Right Side .................................................................9

Rear .........................................................................................11

Lens (supplied with the HXC-FB75KC/HXC-FB75SC)........12

Viewfinder ..............................................................................13

Connection and Setup ......................................................14

Connecting to a Camera Control Unit.....................................14

AC Power Supply (Standalone Operation).............................15

Attaching and Adjusting the Viewfinder ................................16

Attaching the Shoe Conversion Bracket.................................19

Using the Camera for the First Time ......................................19

Attaching and Adjusting the Lens...........................................20

Preparing the Audio Input.......................................................22

Mounting on a Tripod .............................................................23

Attaching the Shoulder Strap ..................................................24

Adjusting the Shoulder Pad Position ......................................24

Shooting.............................................................................25

Basic Procedure for Shooting .................................................25

Adjustments and Settings ................................................26

Changing the Video Format....................................................26

Adjusting the Black Balance and White Balance ...................26

Setting the Electronic Shutter .................................................27

Setting Automatic Iris.............................................................28

Setting the TLCS Function .....................................................29

Setting the Focus Assist Function...........................................29

Setting the Camera Outputs ....................................................30

Adjusting the Audio Level......................................................31

Setting the Digital Extender Function.....................................31

Menus ................................................................................32

Viewfinder Display Screen .....................................................32

Operating the Menu ................................................................33

Selecting a Page......................................................................34

Setting Menu Items.................................................................34

Editing the USER Menu .........................................................35

OPERATION menu................................................................37

PAINT Menu...........................................................................42

MAINTENANCE Menu.........................................................45

FILE Menu..............................................................................48

DIAGNOSIS Menu.................................................................49

Appendix ........................................................................... 49

Usage Precautions ...................................................................49

Cleaning the Viewfinder .........................................................50

Error Messages........................................................................50

Supported USB Flash Drives ..................................................51

Specifications..........................................................................51

Pin Assignment .......................................................................53

Menu Tree...............................................................................56

Open Software Licenses..........................................................58

Overview

The HXC-FB75 HD Color Camera employs a 2/3-inch type “Exmor” CMOS image sensor that achieves a high sensitivity of F12 (1080/59.94i)/F13 (1080/50i) and high S/N ratio of –60 dB. You can use this unit as a studio camera by connecting it to an HXCU-FB70 Camera Control Unit (CCU) using a fiber cable.

Camera System Components

The HXC-FB75 camera system comprises the components shown in the figure below. The operation of the camera head is the same in all cases.

HXC-FB75H

HXC-FB75SC

Cable clamp belt

HDVF-L750 Viewfinder

HXC-FB75 camera head

Microphone

Test chart for flange focal length adjustment

HDVF-L10 Viewfinder

HXC-FB75KC

Shoe conversion bracket

Lens

Indoor hood

V-wedge shoe attachment

System Configuration

Peripherals and related devices for the camera are shown in the figures.

Standalone operation example

AC-DN10 AC Adaptor

Lens

Microphone

VCT-14/U14 Tripod Adaptor

HDVF-L10 Viewfinder

USB flash drive

HXC-FB75

Note

Production of some of the peripherals and related devices shown in the figures may have been discontinued. For advice on choosing devices, please contact your Sony dealer or a Sony service representative.

RCP-1000 series Remote Control Panel

RM-B750/B170 Remote Control Unit

AC power

CCA-5 cable

Sync signal input Video output

HD-SDI/SD-SDI/VBS

Tripod for por table camera

a) No subcarrier phase-lock function with respect to external

reference is available for the VBS signal output from the camera.

System operation example: When connected using an optoelectric composite cable

Microphone

Lens

VCT-14/U14 Tripod Adaptor

Tripod for portable camera

HDVF-L10 Viewfinder

USB flash drive

HXC-FB75

Picture monitor

HDVF-L750 Viewfinder

Return video input

Sync signal input Prompter video input

Optoelectric

composite cable

Intercom headset

Prompter video output

HXCU-FB70 HD Camera Control Unit

AC power

CCA-5 cable / LAN cable

HD-SDI/SD-SDI/VBS/HDMI video output

RCP-1000 series Remote Control Panel

a) The maximum transmission distance is approximately 350 m (1,150 ft) when using Sony CCFN-25/50/

100/150/200/250 Hybrid Fiber Cable (with camera head + portable lens).

b) A LAN cable can be used only to connect the RCP-1500/1501. To connect it, power needs to be supplied

via a PoE hub or power needs to be supplied to the EXT DC IN connector of the RCP-1500/1501.

System operation example: When connected using single-mode optical fiber cables

HDVF-L10 Viewfinder

Microphone

Lens

VCT-14/U14 Tripod Adaptor

Tripod for portable camera

HDVF-L750 Viewfinder

USB flash drive

HXC-FB75

Intercom headset

a) The maximum transmission distance is approximately 10 km (6 miles) when using general-purpose

b) A LAN cable can be used only to connect the RCP-1500/1501. To connect it, power needs to be supplied

AC-DN10 AC Adaptor

AC power

Single-mode optical fiber cables (pair)

HXCU-FB70 HD Camera Control Unit

Prompter video output

Return video input

Sync signal input Prompter video input

AC power

CCA-5 cable / LAN cable

Picture monitor

HD-SDI/SD-SDI/VBS/HDMI video output

RCP-1000 series Remote Control Panel

single-mode fiber cables with LC connectors.

via a PoE hub or power needs to be supplied to the EXT DC IN connector of the RCP-1500/1501.

System operation example: When connected with HXCE-FB70 Power Supply Unit

Microphone

Lens

VCT-14/U14 Tripod Adaptor

Tripod for portable camera

HDVF-L10 Viewfinder

USB flash drive

HXC-FB75

HDVF-L750 Viewfinder

Optoelectric composite cable

Intercom headset

Prompter video output

HXCE-FB70 Powe r S upp ly Unit

Sync signal input Prompter video input

Single-mode optical fiber cables

AC power

HXCU-FB70 HD Camera Control Unit

Return video input

AC power

CCA-5 cable / LAN cable

Picture monitor

HD-SDI/SD-SDI/VBS/ HDMI video output

RCP-1000 series Remote Control Panel

a) The maximum transmission distance is approximately 350 m (1,150 ft) when using Sony CCFN-25/50/

100/150/200/250 Hybrid Fiber Cable (with camera head + portable lens).

b) The maximum transmission distance is approximately 10 km (6 miles) when using general-purpose

single-mode fiber cables with LC connectors.

c) A LAN cable can be used only to connect the RCP-1500/1501. To connect it, power needs to be supplied

via a PoE hub or power needs to be supplied to the EXT DC IN connector of the RCP-1500/1501.

System operation example: When connected using a triaxial cable

HDVF-L10 Viewfinder

USB flash drive

Microphone

HXC-FB75

Lens

VCT-14/U14 Tripod Adaptor

Tripod for portable camera

HDVF-L750 Viewfinder

CA-TX70 HD Camera Adaptor

Intercom headset

Prompter video output

Intercom headset

Triaxial cable

CAC-6 Return Video Selector

Return video input

Sync signal input Prompter video input

HXCU-TX70 HD Camera Control Unit

HKCU-FP2 Front Control Pane l (Attach to front of HXCU-TX70)

a) For details about transmission distance, refer to the operating instructions for the HXCU-TX70 HD Camera

Control Unit.

b) A LAN cable can be used only to connect the RCP-1500/1501. To connect it, power needs to be supplied

via a PoE hub or power needs to be supplied to the EXT DC IN connector of the RCP-1500/1501.

Intercom headset

AC power

CCA-5 cable / LAN cable

Picture monitor

HD-SDI/SD-SDI/VBS video output

RCP-1000 series Remote Control Panel

Name and Function of Parts

Front and Left Side

For the pin assignment of each connector, see “Pin Assignment” (page 53).

a Accessory shoe

Attach to a HDVF-L750/HDVF-L770/HDVF-EL75 viewfinder. To attach a viewfinder, remove the accessory shoe and attach the shoe conversion bracket.

For details about attaching the shoe conversion bracket, see “Attaching the Shoe Conversion Bracket” (page 19).

b Cable clamp attachment

For details about attaching, see “Attaching the cable clamp belt” (page 14).

c Shoulder strap fitting

For details about attaching, see “Attaching the Shoulder Strap” (page 24).

d Microphone holder attachment

For details about attaching, see “Attaching the microphone holder” (page 23).

e Cable clamp

Clamp the lens cable and microphone cable.

f (USB) connector

For details about how to use a USB flash drive and compatible USB flash drives, see “Supported USB Flash Drives” (page 51).

g Viewfinder front-to-back positioning lock knob

Loosen this knob to adjust the front-to-back position of the viewfinder.

h VF (viewfinder) connector (20-pin, round)

Connect the viewfinder cable.

i Viewfinder left-to-right positioning ring

Adjusts the left-to-right position of the viewfinder attached to the viewfinder shoe. Loosen the ring to adjust the viewfinder position, then return the ring to the original position to secure the viewfinder.

j 1/4-inch screw-type accessory shoe

k Slide-type accessory shoe

l Viewfinder front-to-back positioning lever

Adjusts the front-to-back position of the viewfinder attached to the viewfinder shoe. Loosen the lever to adjust the viewfinder position, then return the lever to the original position to secure the viewfinder.

m Viewfinder shoe

Attach the HDVF-L10 viewfinder supplied with the HXC-FB75KC.

For details about attaching, see “Attaching and Adjusting the Viewfinder” (page 16).

n Lens mount securing rubber

After locking the lens in position using the lens locking lever, fit this rubber over the lower of the two projections. This secures the lens mount, preventing it from coming loose.

o Lens mount (special bayonet mount)

Attach a lens. Consult your Sony dealer or a Sony service representative for information about available lenses.

For details about attaching, see “Attaching and Adjusting the Lens” (page 20).

p CCU (Camera Control Unit) connector (optoelectric

composite connector)

Connect to the HXCU-FB70 HD Camera Control Unit. When connected with an optoelectric composite cable, all the signals of the camera, comprising the power supply, control signals, video signals, and audio signals, can be transmitted/received with the one optoelectric composite cable. When connected with a pair of single-mode fiber cables, all the signals except the power supply can be transmitted/received with the pair of single-mode fiber cables.

t AUDIO 1 IN (audio input 1) connector (XLR type, 3-pin,

female)

Connect to audio equipment or a microphone. When the camera is connected to an HXCU-FB70, the input signal will be output from the AUDIO OUTPUT CH-1 connector. You can configure the camera so that the audio is embedded in the output from the SDI output (MIC1) on the <SDI OUT> page in the MAINTENANCE menu.

For details about connecting the microphone supplied with the HXC-FB75KC, see “Connecting a microphone to the AUDIO 1 IN connector” (page 22).

u Audio input 1 selector switch

Select the audio level input to the AUDIO 1 IN connector.

+48V: To supply +48 V phantom power to condenser microphones MIC: When a microphone-level input is connected LINE: When a line-level (0 dBu) signal source is connected

Select +48V when using the microphone supplied with the HXC-FB75KC.

v Trip od mou nt

For details about attaching, see “Mounting on a Tripod” (page 23).

w Lens locking lever

After inserting the lens in the lens mount, rotate the lens mount ring with this lever to lock the lens in position. After locking the lens, be sure to use the lens mount securing rubber to prevent the lens from becoming detached.

x Lens mount cap

Remove by raising the lens locking lever. When no lens is mounted, keep this cap fitted for protection from dust.

q TRUNK connector (D-sub 9-pin)

Use as the trunk signal input/output connector when connected with the HXCU-FB70. It features an assignable pin that can be used, when connected using a dedicated cable, for a function assigned on the <EXT I/O> page in the MAINTENANCE menu.

r Shoulder pad

Raise the shoulder pad fixing lever to adjust the position in the frontto-rear direction. Adjust the position for maximum convenience when operating the camera on your shoulder.

For details about adjusting the position, see “Adjusting the Shoulder Pad Po si tio n” ( page 2 4).

s LENS connector (12-pin)

Connect the lens cable.

Note

When connecting/disconnecting the lens cable, power off the camera first.

Front and Right Side

Note

When connected to a camera control unit or external remote control device (for example, RCP or RM), the following switch functions are controlled from the connected device. The switches on the camera do not function.

• SHUTTER switch

•WHT/BLK switch

• OUTPUT/AUTO KNEE switch

•WHITE BAL switch

• GAIN switch

a FILTER (filter select) knob

Switch between four built-in ND filters. When this switch is adjusted, the filter setting appears in the viewfinder for about three seconds.

FILTER knob setting ND filter

1Clear

2 1/4 ND (attenuates light to approximately 1/4)

3 1/16 ND (attenuates light to approximately 1/16)

4 1/64 ND (attenuates light to approximately 1/64)

b Shoulder strap fitting

For details about attaching, see “Attaching the Shoulder Strap” (page 24).

c ASSIGN (assignable) 1/2/3 buttons

You can assign functions to these buttons using ASSIGNABLE 1/2/ 3 on the <SWITCH ASSIGN1> page in the OPERATION menu. No function is assigned by factory default.

d COLOR TEMP. (color temperature) button

Press the button, turning it on, to change the color temperature for shooting (factory default: 5600K). You can assign a function to this button using ASSIGN CTEMP on the <SWITCH ASSIGN1> page in the OPERATION menu.

e SHUTTER switch

Set to the ON position to use the electronic shutter. Set to the SEL position to switch the shutter speed or shutter mode display. When this switch is operated, the shutter settings appear in the viewfinder for about three seconds.

f RET (return video) button

Displays the return video signal in the viewfinder while this button is pressed. You can assign a function to this button using FRONT RET on the <SWITCH ASSIGN2> page in the OPERATION menu.

Note

The display image may be distorted when the video signal is switched.

g INTERCOM LEVEL knob

When connected with the HXCU-FB70, use this knob to adjust the intercom/earphone volume level. The intercom volume level can also be adjusted using the INTERCOM knob on the rear of the camera. When the camera is used in standalone operation mode, use this knob to set the gain for microphones connected to the AUDIO 1 IN and AUDIO 2 IN connectors. You can assign a function to this knob using FRONT VR on the <VR ASSIGN> page in the OPERATION menu.

h Menu control knob (rotary encoder)

Rotate to select settings from menus displayed in the viewfinder and press to confirm settings.

i WHT/BLK (automatic white/black balance adjustment)

switch

Automatically adjusts the white balance and black balance. WHT: Adjust the white balance automatically. If the WHITE BAL

switch is set to A or B, the white balance setting is stored in the corresponding memory (A or B). If the WHITE BAL switch is set to PRST, the adjustment function does not operate.

BLK: Adjust the black set and black balance automatically. You can use the WHT/BLK switch even when the ATW (Auto Tracing White Balance) function is operating. If you push the switch to the WHT position once more during automatic white balance adjustment, the adjustment is canceled and the white balance setting returns to the original setting. If you push the switch to the BLK position once more during the automatic black balance adjustment, the adjustment is canceled and the black balance setting returns to the original setting.

m OUTPUT (output signal select)/AUTO KNEE switch

Select the signal that is output from the camera.

BARS: Output the color bar signal. CAM: Output the video signal being shot. When this is selected, you

can switch the AUTO KNEE function

1) AUTO KNEE function: Against a very bright background with the iris opening adjusted for the subject, objects in the background will be lost in the glare. The AUTO KNEE function suppresses areas of high brightness automatically to reproduce the background more clearly. This is particularly effective in the following cases.

• Shooting people in the shade on a sunny day

• Shooting a subject indoors, against a background through a window

• Any high contrast scene

ON/OFF.

n WHITE BAL (white balance memory select) switch

Set the white balance adjustment method. When this switch is adjusted, the new setting appears in the viewfinder for about three seconds. PRST: Adjust the color temperature to the preset value (factory

default: 3200K). Use this setting when you have no time to adjust the white balance.

A or B: Recall the white balance adjustment value already stored in

memory A or B. Push the WHT/BLK switch to the WHT position to automatically adjust the white balance and save the adjustment value in memory A or memory B.

o CAMERA POWER switch and indicator

Set to one of the following, according to the power supply method.

CCU: When supplying power from the camera control unit EXT: When supplying power on the DC IN connector or camera

adaptor power connector

The indicator lights up in green during operation.

j GAIN switch

Switch the gain of the video amplifier to match the lighting conditions during shooting. When this switch is adjusted, the new setting appears in the viewfinder for about three seconds. The gain values corresponding to the L, M, and H settings are specified using GAIN on the <SWITCH ASSIGN1> page in the OPERATION menu (factory default: L=0 dB, M=6 dB, and H=12 dB).

k STATUS/CANCEL switch

STATUS: Displays camera status information when no menu is

displayed and the DISPLAY/MENU switch is set to DISPLAY.

CANCEL: Cancel changed settings or return the display to the

previous menu when a menu is displayed.

l DISPLAY/MENU switch

Select the display in the viewfinder. DISPLAY: Displays various textual information and markers, such

as messages showing the camera settings and operating status, the center marker, and the safety zone marker, in addition to the camera image.

OFF: Displays the camera image only. MENU: Display the menu, in addition to the camera image.

Rear

For the pin assignment of each connector, see “Pin Assignment” (page 53).

For details about removing the rear cover, see “Removing the rear cover” (page 15).

(With rear cover removed)

c RET1 (return video 1) button

Displays the return video 1 signal in the viewfinder while this button is pressed.

d INTERCOM (intercom volume) knob

Adjust the intercom volume level. When connected with the HXCU-FB70, the intercom volume level can also be adjusted using the INTERCOM LEVEL knob on the rear of the camera. In standalone operation mode, you can assign a function to this knob using REAR VR on the <VR ASSIGN> page in the OPERATION menu.

e INTERCOM MIC (intercom microphone) switch

The switch function varies depending on the PANEL TYPE setting on the <INTERCOM> page in the OPERATION menu (factory default: CE).

When the PANEL TYPE setting is CE

Functions as the intercom microphone line selector switch.

PROD: Output the microphone on the PROD line. OFF: Turn the microphone OFF. ENG: Output the microphone on the ENG line.

When the PANEL TYPE setting is UCJ

Functions as the intercom line and microphone ON/OFF selector switch.

PROD: Select the PROD line and turn the microphone OFF. OFF: Select the ENG line and turn the microphone OFF. ENG: Select the ENG line and turn the microphone ON (output on

ENG line). You can have a conversation on the selected line while the assignable button on the rear is pressed by assigning the function that turns the intercom microphone ON to the button.

a PGM LEVEL (program level) knob/assignable button

Adjust the intercom PGM audio level. When connected with the HXCU-FB70, this adjusts the PGM audio level input from the camera control unit. In standalone operation mode, this adjusts signal level input on the SDI IN connector. No function is assigned to the assignable button by factory default. You can have a conversation on the intercom line while the button is pressed by assigning the function that turns the intercom microphone ON using REAR ENC SW on the <SWITCH ASSIGN2> page in the OPERATION menu.

b RET2 (return video 2) selector switch

Select the return video signal (2, 3, 4) displayed when the button assigned with the return video 2 function is pressed.

Note

The intercom and microphone of the camera can be used when connected to a CA-TX70. The intercom is connected to the line selected using the INTERCOM switch of the CA-TX70. ENG/PROD cannot be selected on the camera.

f CALL button

When you press this button, the red tally indicators on the connected camera control unit and external control device (for example, RCP or RM) will light up.

g TALLY indicators (red/green)

When the TALLY switch is set to ON, the tally indicator lights up when a tally signal is input to the connected camera control unit or a call signal is generated by pressing the CALL button.

h TALLY s wit c h

Set to ON to activate the TALLY indicator function.

i Camera adaptor attachment

Attach an optional CA-TX70 HD Camera Adaptor and AC-DN10 AC Adaptor.

j EARPHONE jack (stereo, minijack)

Monitor the audio output from the intercom or audio signals input to the AUDIO 1 IN and AUDIO 2 IN connectors. Set the earphone output on the <EARPHONE> page in the OPERATION menu. The earphone volume level can be adjusted using the INTERCOM LEVEL knob.

k Audio input 2 selector switch

Select the audio level input to the AUDIO 2 IN connector.

+48V: To supply +48 V phantom power to condenser microphones MIC: When a microphone-level input is connected LINE: When a line-level (0 dBu) signal source is connected

l REMOTE (remote control) connector (8-pin)

Connect a remote control unit for remote control the camera.

Note

Before connecting/disconnecting a remote control unit, power off the camera first.

m TEST OUT connector (BNC type)

Outputs an analog signal. You can select the VBS signal, Y signal of the VF connector, HDSYNC, or SD-SYNC for output in the MAINTENANCE menu.

n SDI OUT connector (BNC type)

Outputs an HD-SDI or SD-SDI signal. You can select the output signal in the MAINTENANCE menu.

o DC IN (DC power supply input) connector (XLR 4-pin,

female)

To operate the camera from an external DC power supply, connect an optional DC power cord to this connector and then connect the cord to an AC-DN10 AC Adaptor or other source.

p INTERCOM connector (XLR 5-pin)

Connect an XLR 5-pin headset for input and output of intercom audio signals.

Lens (supplied with the HXC-FB75KC/ HXC-FB75SC)

For details about attaching a lens, see “Attaching and Adjusting the Lens” (page 20).

q AUDIO 2 IN (audio input 2) connector (XLR type, 3-pin,

female)

Connect to audio equipment or a microphone. When connected with the HXCU-FB70, the input signal will be output from the AUDIO OUTPUT CH-2 connector. You can configure the camera so that the audio is embedded in the output from the SDI output (MIC2) on the <SDI OUT> page in the MAINTENANCE menu.

r Tail guard

Protects the cables connected to the connectors on the rear.

s DC OUT (DC power supply output) connector (4-pin,

female)

Supplies power to a script light or other device (maximum 1.5 A).

t PROMPTER/GENLOCK (prompter signal output/external

sync signal input) connector (BNC type)

When connected with a CCU, this connector outputs a VBS prompter signal. In standalone operation mode, connect an external sync signal (BB or tri-level sync) for synchronizing the camera. If a VBS signal is input, you can check the input image in the viewfinder by pressing the RET button on the camera.

u SDI IN connector (BNC type)

In standalone operation mode, this displays the HD-SDI signal input on the SDI IN connector in the viewfinder when the RET button is pressed. You can select the input signal to be displayed in the viewfinder on the <EXT RETURN> page in the MAINTENANCE menu.

Notes

• Only HD-SDI signals in the same format specified on the <OUTPUT FORMAT> page in the MAINTENANCE menu can be input on the SDI IN connector.

• Signals input on the SDI IN connector cannot be displayed when SD-SDI is selected on the <SDI OUT> page in the MAINTENANCE menu.

a RET (return video) button

Displays the return video signal in the viewfinder while this button is pressed.

b Zoom see-saw switch

This is enabled when the zoom servo/manual selector knob is in the SERVO position. The zoom speed increases when you push the switch deeper, and decreases when you push less deeply.

W (Wide): Wide angle. T (Telephoto): Telephoto.

c Iris operation mode selector switch

A (Auto): The iris is adjusted automatically. M (Manual): Adjust the iris with the iris ring.

d Iris one-push auto switch

When the iris operation mode selector switch is in the M position for manual adjustment, press this switch for instantaneous auto iris adjustment. The iris is automatically adjusted while the switch is pressed.

e Iris gain adjustment trimmer

Adjust the iris gain when the iris operation mode selector switch is in the A (Auto) position. Flip off the rubber cap, and turn the iris gain adjustment trimmer using a screwdriver or similar object. Turn clockwise to increase the gain, and turn counterclockwise to decrease the gain.

f F.B. l o c k scr e w/F.B . a djus t m ent r i n g

Use to adjust the flange back (flange focal length).

g Positioning pin

When attaching a lens, align this pin with the slot in the top center of the lens mount on the camera.

h Macro button/macro ring

Press and hold the macro button and rotate the macro ring to focus (close-up: 10 mm minimum).

i Iris ring

For manual iris adjustment, set the iris operation mode selector switch to the M (manual) position, then rotate this ring.

Note

Always set the iris operation mode selector switch to the M (manual) position before rotating the ring.

j Zoom lever/zoom ring

For manual zoom adjustment, set the zoom servo/manual selector switch to the MANU (manual) position, then operate this lever/ring.

k Focus ring

Rotate this ring to adjust the focus.

Viewfinder

This section describes the HDVF-L10 viewfinder supplied with the HXC-FB75KC.

For details about attaching and adjusting the HDVF-L10 viewfinder, see “Attaching and Adjusting the Viewfinder” (page 16).

For details about the viewfinder supplied with the HXC-FB75SC, refer to the operation manual for the HDVF-L750.

l Zoom servo/manual selector knob

SERVO: Power (servo) zoom. Control the zoom using the zoom

see-saw switch.

MANU (Manual): Manual zoom. Control the zoom using the zoom

lever/zoom ring.

m Lens cable

Connect to the LENS connector on the camera.

n VTR button

You can assign a function to this button using LENS VTR S/S on the <SWITCH ASSIGN2> page in the OPERATION menu.

o Zoom remote control connector

Connecting an optional zoom servo controller allows remote control of zooming.

a Connector

Connect to the VF connector on the camera.

b Slide stopper

Prevents the viewfinder from coming off the camera when it is slid from side to side.

c Eyecup

d Diopter adjustment ring

Rotate the ring to adjust the image for clear focus.

e Eyepiece

You can raise the eyepiece or remove it when required by the usage situation.

f Viewfinder barrel

You can raise the viewfinder barrel or remove it when required by the usage situation.

g Tall y indi c ato r

The indicator lights up when a red tally signal is input to the camera. When an abnormality occurs, the tally indicator flashes to indicate a warning.

h PEAKING knob

Rotate clockwise to adjust the picture sharpness to make lens focusing easier. This has no effect on the output signal of the camera.

i CONTRAST knob

Adjust the contrast of the screen. This has no effect on the output signal of the camera.

j BRIGHT knob

Adjust the brightness of the screen. This has no effect on the output signal of the camera.

k TALLY s wit c h

Used to control the tally indicator on the viewfinder.

HIGH: The tally indicator brightness is set to high. OFF: The tally indicator is disabled. LOW: The tally indicator brightness is set to low.

l ZEBRA (zebra pattern) switch

Use to control the zebra pattern display.

ON: Display the zebra pattern. OFF: Do not display the zebra pattern.

Connection and Setup

Connecting to a Camera Control Unit

When operating the camera in a system with a camera control unit (CCU), connect the CCU connector of the camera and the CAMERA connector of the CCU using an optoelectric composite cable. When required, secure the cable, using the supplied cable clamp belt.

If connecting an HXCU-TX70 HD Camera Control Unit, refer to the operating instructions for the HXCU-TX70.

Attaching the cable clamp belt

1 Insert the belt bracket C into hole A or B of the cable

clamp belt.

m DISPLAY switch

Use to control the display of text information.

ON: Display text information. OFF: Do not display text information.

Also used when switching to full-screen display mode or reduced display mode.

Note

There may be a mismatch between the DISPLAY switch ON/OFF state and the actual ON/OFF operation, depending on the camera settings.

n MIRROR switch

Used to reverse the image display on the monitor screen horizontally or vertically when the viewfinder barrel is raised up or rotated.

L/R (left/right): Reverse the image horizontally. OFF: Do not reverse the image. B/T (bottom/top): Reverse the image vertically.

o Viewfinder cable

p Microphone holder

2 1 Remove the screw-hole cover on the top rear of the

camera and 2 secure the cable clamp belt to the camera using the two supplied screws (+B3×10).

3 1 Release the buckle, 2 bundle the cable with the belt, 3

then close the buckle again.

4 Adjust the length by pulling down on the end of the belt.

AC Power Supply (Standalone Operation)

Prepare an AC power supply when using the camera in standalone operation mode (without a CCU). For safety, use only the Sony AC adaptor listed below.

• AC adaptor: AC-DN10

If using the DC IN connector

Connect the AC-DN10 AC adaptor to the DC IN output connector on the camera using an optional DC power cord.

Attaching the AC adaptor

Attach an optional AC-DN10 AC adaptor to the camera, then connect to the AC power supply. The AC-DN10 can supply up to 100 W of power.

To AC outlet

To attach the rear cover

Align the guide on the inner side of the rear cover with the camera adaptor mount, and insert the cover.

If attaching the AC adaptor

Remove the rear cover and attach the AC adaptor to the camera.

Removing the rear cover

1 Hold the release button on the camera in, and 2 pull the rear cover up.

Rear cover

Attaching and Adjusting the Viewfinder

Warn ing

When the viewfinder is attached, do not leave the camera with the eyepiece facing the sun. Direct sunlight can enter through the eyepiece, be focused in the camera and cause a fire.

This section describes how to attach and adjust the HDVF-L10 viewfinder supplied with the HXC-FB75KC. For details about attaching and adjusting the viewfinder supplied with the HXC-FB75SC, refer to the operation manual for the HDVF-L750.

Attaching the viewfinder

Attach the HDVF-L10 viewfinder supplied with the HXC-FB75KC.

Notes

• Be sure to power off the camera before plugging the viewfinder connector into the VF connector of the camera. If the connector is plugged in while the power is on, the viewfinder may not operate correctly.

• Plug the viewfinder connector all the way into the VF connector of the camera. If the connector is not firmly connected, the image may become distorted or the tally indicator may not operate properly.

To detach the viewfinder

Detach in the reverse procedure of attaching. When detaching the viewfinder from the shoe, lift up the slide stopper on the viewfinder.

Adjusting the position

To adjust the viewfinder left-to-right position, loosen the left-toright positioning ring. To adjust the front-to-back position, loosen the front-to-back positioning lever and lock knob.

Viewfinder left-to-right positioning ring

1 1 Loosen the viewfinder left-to-right positioning ring, 2

attach the viewfinder to the viewfinder shoe, and 3 tighten the viewfinder left-to-right positioning ring.

Slide stopper

2 Connect the viewfinder connector to the VF connector.

VF connector

Viewfinder front-to-back positioning lever and lock knob

Adjusting the angle

You can adjust the angle of the viewfinder.

To reverse the display (image/text indication) vertically

The viewfinder can be rotated as much as 180 degrees so that it is facing the subject. In this case, the image and other information displayed appear upside down on the screen. To restore the normal display, set the MIRROR switch on the viewfinder to the B/T position to flip the display vertically.

Raising the viewfinder barrel or eyepiece

You can view the LCD screen inside the viewfinder or its mirrored image by raising the viewfinder barrel or eyepiece. This section describes how to raise and detach the viewfinder barrel. The eyepiece can also be raised and detached in the same way.

To raise the viewfinder barrel

1 Push the clip on the bottom to release it, and 2 flip up the viewfinder barrel. It locks at the 120-degree position.

LCD screen

To detach the viewfinder barrel

Keep in the lock position for normal use. You can also open it farther from the lock position. To set to the 120degree position again, return it to the closed position and then open it again.

1 Push the clip on the bottom to release it. 2 Flip up the viewfinder barrel. 3 Slide the button on the top in the direction opposite to the

viewfinder barrel to unlock the barrel.

4 Detach the viewfinder barrel by sliding it horizontally.

To reverse the display (image/text indication) horizontally

Set the MIRROR switch on the viewfinder to the L/R position to reverse the picture and other information displayed in the viewfinder horizontally.

Adjusting the diopter

Rotate the diopter adjustment ring until the viewfinder image is sharpest.

Diopter adjustment ring

Adjusting the screen

Reduced display mode

Displays the camera image at a reduced size, with the tally and other indicators displayed in the spaces above and below the camera image. Use this mode when the clear visibility of the tally and other indicators is more important.

Indicators are located at the top and bottom of the screen to indicate the status of the camera and viewfinder.

a G TALLY (green tally) indicator (green)

Lights up when a green tally signal is input.

b R TALLY (red tally) indicator (red)

Lights up when a red tally signal is input.

c Y TALLY (yellow tally) indicator (yellow)

Not supported by the camera.

You can adjust the following items.

Peaking: Adjust using the PEAKING knob. Contrast: Adjust using the CONTRAST knob. Brightness: Adjust using the BRIGHT knob.

Screen display mode and indicator

The viewfinder screen can be set to full-screen display mode or reduced display mode. To switch the display mode, switch the DISPLAY switch “ON t OFF t ON t OFF” or “OFF t ON t OFF t ON” in quick succession.

Full-screen display mode

Displays the image so that it fills the full-screen display area. Tally and other indicators are superimposed on the camera image. Use this mode when the resolution of the displayed image is more important.

Note

In full-screen display mode, the display position of the tally indicators is fixed in one location. Accordingly, only one R/G/Y tally indicator can be lit at any one time, regardless of the signal that is input. The display priority of the tally indicator is red, green, and yellow, in that order.

d [!] indicator (amber)

Using the ‘!’ IND function, the ‘!’ indicator appears when nonstandard settings are in effect.

e BATT (battery) indicator (red)

Lights up or flashes to indicate the status of the power supply to the camera.

Lit: Significant voltage decrease Flashing: Voltage decrease

f SAVE indicator (amber)

Not supported by the camera.

+ 40 hidden pages

Sony HXC-FB75H User Guide

Table of Contents

Overview

Name and Function of Parts

Connection and Setup