Sony HCD-GTR88 Service Manual

SERVICE MANUAL
Sony Corporation
Audio & Video Business Group Published by Sony EMCS (Malaysia) PG Tec
HCD-GTR88
COMPACT DISC DECK RECEIVER
9-890-544-01
©
2010.04
E Model
Australian Model
Ver. 1.0 2010.04
• HCD-GTR88 is the amplifi er, USB, CD player, tuner and tape deck (only E4 Model) section in MHC-GTR88. Photo: HCD-GTR88 (E4 Model)
CD Section
Model Name Using Similar Mechanism HCD-GTZ4/GTZ4i/GTZ5 CD Mechanism Type CDM88BL-DVBU101 Optical Pick-up Name KHM-313CAB/C2NP
Tape Deck Section (only for E4 Model)
Model Name Using Similar Mechanism HCD-GT111/GT222/GT444/GT555 Tape Mechanism Type CS-21SC-900TP
SPECIFICATIONS
Amplifi er section
The following are measured at Mexican model: AC 127 V, 60 Hz Other models: AC 120 V, 220 V, 240 V, 50/60 Hz Front/Satellite Speaker Power Output (rated): 200 W + 200 W (at 6 , 1 kHz, 1% THD) Front Speaker RMS output power (reference): 345 W + 345 W (per channel at 8 , 1 kHz) Satellite Speaker RMS output power (reference): 140 W + 140 W (per channel at 24 , 1 kHz) Subwoofer RMS output power (reference): 200 W + 200 W (per channel at 6 , 100 Hz)
Inputs
PC (AUDIO IN) L/R Voltage 700 mV, impedance 47 kilohms MIC Sensitivity 1 mV, impedance 10 kilohms
(USB) port: Type A
Outputs
PHONES Accepts headphones of 8 or more
USB section
Supported bit rate MP3 (MPEG 1 Audio Layer-3): 32 kbps – 320 kbps, VBR WMA: 48 kbps – 192 kbps AAC: 48 kbps – 320 kbps Sampling frequencies MP3 (MPEG 1 Audio Layer-3): 32 kHz/44.1 kHz/48 kHz WMA: 44.1 kHz AAC: 44.1 kHz Transfer speed Full-Speed Supported USB device Mass Storage Class Maximum current 500 mA
Disc player section
System Compact disc and digital audio system Laser Diode Properties Emission Duration: Continuous Laser Output*: Less than 44.6 W * This output is the value measurement
at a distance of 200 mm from the objective lens surface on the Optical
Pick-up Block with 7 mm aperture. Frequency response 20 Hz – 20 kHz Signal-to-noise ratio More than 90 dB Dynamic range More than 88 dB
Tape deck section (For African model only)
Recording system 4-track 2 channel, stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range North American and Brazilian models:
87.5 MHz – 108.0 MHz (100 kHz step) Other models:
87.5 MHz – 108.0 MHz (50 kHz step) Antenna FM lead antenna Antenna terminals 75 ohms unbalanced Intermediate frequency
10.7 MHz
AM tuner section
Tuning range Pan American and Oceanian models: 530 kHz – 1,710 kHz (with 10 kHz tun-
ing interval)
531 kHz – 1,710 kHz (with 9 kHz tuning
interval) Other models: 530 kHz – 1,610 kHz (with 10 kHz tun-
ing interval) 531 kHz – 1,602 kHz (with 9 kHz tuning
interval) Antenna AM loop antenna, external antenna
terminal Intermediate frequency 450 kHz
General
Power requirements Oceanian model: AC 230 V – 240 V,
50/60 Hz Mexican model: AC 127 V, 60 Hz Argentina model: AC 220 V, 50/60 Hz Other models: AC 120 V, 220 V or 230 V – 240 V, 50/60 Hz, Adjustable
with voltage selector Power consumption: 460 W Dimensions (w/h/d) (excl. speakers) (Approx.) 231 mm × 361 mm × 518 mm Mass (excl. speakers) (Approx.) African and Pan Asian models: 16.2 kg Other models: 15.7 kg
Design and specifi cations are subject to change without notice.
• Abbreviation
E4 : African model
HCD-GTR88
2
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam­aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsol­dering.
SAFETY-RELA TED COMPONENT W ARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL T O SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
CAUTION Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radia­tion exposure.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safe­ty check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-
540A. Follow the manufacturers’ instructions to use these instru­ments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital
multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or
battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
1.5 k0.15 F
AC voltmeter (0.75 V)
To Exposed Metal Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior.
T ABLE OF CONTENTS
1. SERVICING NOTES
.............................................. 3
2. DISASSEMBLY
2-1. Disassembly Flow ........................................................... 5
2-2. Case (Side-L/R) .............................................................. 6
2-3. Top Case.......................................................................... 6
2-4. Tape Mechanism Deck (For African Model only) .......... 7
2-5. Front Panel Block, HUB Board, DMB19 Board ............ 7
2-6. DC Fan (M101) ............................................................... 8
2-7. Back Panel, SUBTRANS Board ..................................... 8
2-8. MAIN Board .................................................................. 9
2-9. DC Fan (M101), PT SHIELD Board,
POWER AMP Board Section ......................................... 9
2-10. POWER AMP Board, SUBWOOFER Board ................. 10
2-11. Chassis Section ............................................................... 10
2-12. CD Mechanism Block (CDM88BL-DVBU101) ............ 11
2-13. Optical Pick-up Block (KHM-313CAB) ........................ 11
2-14. Belt (DLM3A) ................................................................ 12
3. TEST MODE
............................................................. 13
4. MECHANICAL ADJUSTMENTS
....................... 15
5. ELECTRICAL ADJUSTMENTS
......................... 16
6. DIAGRAMS
6-1. Block Diagram - RF SERVO, USB Section - ................. 17
6-2. Block Diagram - MAIN Section - ................................... 18
6-3. Block Diagram - AMP Section - ..................................... 19
6-4. Block Diagram - DISPLAY,
POWER SUPPLY Section - ............................................ 20
6-5. Printed Wiring Board - DISPLAY Board - ..................... 22
6-6. Schematic Diagram - DISPLAY Board - ........................ 23
6-7. Printed Wiring Board - DMB19 Board - ........................ 24
6-8. Schematic Diagram - DMB19 Board (1/3) - .................. 25
6-9. Schematic Diagram - DMB19 Board (2/3) - .................. 26
6-10. Schematic Diagram - DMB19 Board (3/3) - .................. 27
6-11. Printed Wiring Board - POWER AMP Board - .............. 28
6-12. Schematic Diagram - POWER AMP Board - ................. 29
6-13. Printed Wiring Board - MAIN Board - ........................... 30
6-14. Schematic Diagram - MAIN Board (1/3) - ..................... 31
6-15. Schematic Diagram - MAIN Board (2/3) - ..................... 32
6-16. Schematic Diagram - MAIN Board (3/3) - ..................... 33
6-17. Printed Wiring Board - MIC, VOL and USB Board - .... 34
6-18. Schematic Diagram - MIC, VOL and USB Boards - ...... 35
6-19. Printed Wiring Board - TC Board - ................................. 36
6-20. Schematic Diagram - TC Board - ................................... 36
6-21. Printed Wiring Board
- TRANS and SUBTRANS Board - ............................... 37
6-22. Schematic Diagram
- TRANS and SUBTRANS Boards - .............................. 38
6-23. Printed Wiring Board - SUBWOOFER Board - ............. 39
6-24. Schematic Diagram - SUBWOOFER Board - ................ 40
6-25. Printed Wiring Board - HUB Board - ............................. 41
6-26. Schematic Diagram - HUB Board - ................................ 42
7. EXPLODED VIEWS
7-1. Case Section .................................................................... 53
7-2. Top Panel Section ........................................................... 54
7-3. Loading Panel Section, HUB Board Section,
DMB19 Board Section .................................................... 55
7-4. DISPLAY Board Section ............................................... 56
7-5. Front Panel Section ......................................................... 57
7-6. Back Panel Section ......................................................... 58
7-7. MAIN Board Section ..................................................... 59
7-8. Chassis Section ............................................................... 60
7-9. CD Mechanism Section (CDM88BL-DVBU101) ......... 61
8. ELECTRICAL P ARTS LIST
............................... 62
HCD-GTR88
3
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro­static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body . During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The
exible board is easily damaged and should be handled with
care.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead. (
Caution:
Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution:
The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to
ow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE OF REPLACING THE IC102 ON THE DMB19 BOARD
IC102 on the DMB19 board cannot exchange with single. When this part is damaged, exchange the entire mounted board.
RELEASING THE DISC TRA Y LOCK
The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.
Releasing Procedure:
1. Press [I/1 STANDBY] button to turn the power on.
2. Press the [CD] button to select CD function.
3. While pressing the [
x
] button, press the [Z OPEN/CLOSE]
button for more 5 seconds).
4. The message “UNLOCKED” is displayed and the disc tray is unlocked.
Note:
When LOCKED is displayed, the slot lock is not released by
turning power on/off with the
[I/1 STANDBY] button.
MODEL IDENTIFICA TION – Back Panel –
• Abbreviation AR : Argentina model AUS : Australian model E2 : 120V AC area in E model E4 : African model E51 : Chilean and Peruvian models
MX : Mexican model
Model Part No.
HCD-GTR88: E2, E51
4-164-385-0[]
HCD-GTR88: AR
4-164-385-1[]
HCD-GTR88: MX
4-164-385-2[]
HCD-GTR88: E4
4-164-385-4[]
HCD-GTR88: AUS
4-164-385-5[]
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc re
ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
PART No.
HCD-GTR88
4
HOW TO DISTINGUISH T APE MECHANISM DECK
Two kinds of tape mechanism decks installed by this set exist.
Please do the repair exchange after con
rming which tape mechanism deck set of the repair according to how to distinguish the fi gure below.
Tape Deck Name Tape Deck Part No. Belt Part No.
CS-21SC-900TP 1-797-575-11
2-688-621-01 BELT (R/F) 2-688-622-01 BELT (MAIN)
motor
Mold part: CS-21SC-900TP
tape deck
HOW TO OPEN THE TRA Y WHEN POWER SWITCH TURN OFF
Step:
1) Work after removing the case (side-R and side-L) referring to “2.2. CASE (SIDE-L/R)” on disassembly (page 6).
2) Work after removing the top case referring to “2-3. TOP CASE” on disassembly (page 6).
lever
state of opening the CD tray
gear
d
Turn a gear by a driver till a lever rises up to the position of the figure. (Try to push gear at the same time slowly pull Front panel away.)
a
c
c
b
e
HCD-GTR88
5
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note:
Follow the disassembly procedure in the numerical order given.
2-6. DC FAN (M101) (Page 8)
2-2. CASE (SIDE-L/R) (Page 6)
2-3. TOP CASE (Page 6)
2-5. FRONT PANEL BLOCK, HUB BOARD, DMB19 BOARD (Page 7)
2-7. BACK PANEL, SUBTRANS BOARD (Page 8)
2-8. MAIN BOARD (Page 9)
2-11. CHASSIS SECTION (Page 10)
2-9. DC FAN (M101), PT SHIELD BOARD, POWER AMP BOARD SECTION (Page 9)
2-10. POWER AMP BOARD, SUBWOOFER BOARD (Page 10)
2-12. CD MECHANISM BLOCK (CDM88BL-DVBU101) (Page 11)
2-13. OPTICAL PICK-UP BLOCK (KHM-313CAB) (Page 11)
SET
2-4. TAPE MECHANISM DECK (FOR AFRICAN MODEL ONLY) (Page 7)
2-14. BELT (DLM3A) (Page 12)
HCD-GTR88
6
2-2. CASE (SIDE-L/R)
2-3. TOP CASE
2 three screws (BVTP3 u 10)
4 case (side-R)
1 four screws
(case 3 TP2)
3
2 three screws
(BVTP3 u 10)
Tape deck section (For African model only)
4 case (side-L)
1 four screws
(case 3 TP2)
3
Tape deck section (For African model only)
1 one screw (BVTP3 u 10)
3 two claws
2 wire (flat type) (9 core)
(CN450)
4 Lift up the back side of top case.
5 top case
HCD-GTR88
7
2-4. TAPE MECHANISM DECK (FOR AFRICAN MODEL ONLY)
2-5. FRONT PANEL BLOCK, HUB BOARD, DMB19 BOARD
6 bracket (deck)
5 two screws
(BVTP2.6 u8)
7 two screws (BVTP2.6 u8)
9 tape mechanism deck
1 CN501 (8P)
3 two screws
(BVTP3 u 8)
2 Cut the clamp.
8 Open the cassette box.
4 TC board
top panel block
qd wire (flat type) (13 core) (CN410)
lever
1 Turn a gear by a driver till a lever rises up to the position of the figure.
state of opening the CD tray
gear
4 wire (flat type) (23 core) (CN405)
8 one screw (BVTP3 u 10)
q; front panel block
3 panel loading
9 five screws
(BVTP3 × 8)
8 one screw (BVTP3 × 10)
7 CN1501 (10P)
6 CN470 (7P)
5 wire (flat type) (11 core)
(CN403)
qk DMB19 board: CN1105 (4P)/ HUB board: CN1500 (4P)
qg two screws (BVTP3 u8)
qa CD block
qj HUB
board
wd two screws (BVTP3 u10)
wg four screws (BVTP3 u8)
wf wire (flat type) (9 core) (CN1106)
wh DMB19 board
ql bracket
(ground hub)
qh CN201 (6P)
w; CN650 (8P)
qs wire (flat type) (24 core)
(CN101)
wa CN601 (9P)
ws wire (flat type) (7 core)
(CN4602)
qf saranet cushion
2 Pull the tray by hand.
HCD-GTR88
8
2-6. DC FAN (M101)
2-7. BACK PANEL, SUBTRANS BOARD
2 cover fan (GVX7S)
1 four screws
(BVTP3 u 8)
3 two screws (BVTP3 u 8)
4 DC fan (M101)
5 CN600 (3P)
1 wire (flat type) (9 core)
(CN220)
qj binding band (taiton)
2 CN1200 (3P)
4 CN691 (4P)
3 CN1201 (4P)
qk clamp filter
(ferrite core)
qf Bracket (Subtrans)
qd SUBTRANS board
wa back panel
qh tuner (FM/AM)
qg two screws
(BVTT3 u 6)
5 one screw (BVTP3 u 8)
qs two screws (BVTP3 u 8)
6 one screw (BVTP3 u 8)
7 two screws (BVTP3 u 8)
w; power cord
8 one screw
(BVTP3 u 8) 9 one screw (BVTP3 u 8)
q; one screw (BVTP3 u 8)
ql cord bush
qa
HCD-GTR88
9
2-8. MAIN BOARD
2-9. DC FAN (M101), PT SHIELD BOARD, POWER AMP BOARD SECTION
4 CN550 (6P)
5 MAIN board
3 CN200 (12P)
1 three screws
(BVTP3
u 8)
2 CN100 (10P)
1 one screw
(BVTP3 u 8)
6 POWER AMP board section
5 CN1302 (3P)
q; DC Fan (M101)
8 DC Fan bracket
2 PT SHIELD board
3 three screws
(BVTP3 u 8)
9 two screws (BVTP3 u 8)
7 two screws (BVTP3 u 8)
qa one screw (BVTP3 u 8)
4 CN1250 (13P)
qs clamp
HCD-GTR88
10
2-10. POWER AMP BOARD, SUBWOOFER BOARD
2-11. CHASSIS SECTION
1 one screw (BVTP3 u 8)
6 two screws (BVTP3 u 8)
7 Bracket (PWB)
5 POWER AMP board
8 heat sink
q; SUBWOOFER board
2 one screw
(BVTP3 u 8)
3 two screws (transistor)
9 two screws (transistor)
4 CN803 (7P)
1 two screws
(BVTP3 u8)
1 two screws (BVTP3 u8)
3 chassis block
2
HCD-GTR88
11
2-12. CD MECHANISM BLOCK (CDM88BL-DVBU101)
2-13. OPTICAL PICK-UP BLOCK (KHM-313CAB)
qa sheets (CDM)
8 one screw
(BVTP3 u 8)
6 cover dust (CDM88-A-BTM)
5 cover (shutter)
1 wire (flat type) (13 core)
(MOTOR board)
7 three sheets (CDM)
q; CD mechanism block
(CDM88BL-DVBU101)
8 one screw (BVTP3 u8)
9 cover dust (CDM88-A-top)
2 one screw
(BVTP3 u8)
3 bracket (MTK)
4
CD mechanism block (CDM88BL-DVBU101)
4 two insulator screws
5 two insulators
4 two insulator screws
5 two insulators
7 optical pick-up block
(KHM-313CAB)
3 connector
6 holder BU
1 four screws
(BVTP2.6)
2 wire (flat type) (24 core)
HCD-GTR88
12
2-14. BELT (DLM3A)
2
four screws
3
cover
4
two belts (DLM3A)
belt
belt
position of belt
gear
lever
1 Turn a gear till a lever rises up to the position of the figure.
state of opening the CD tray
HCD-GTR88
13
SECTION 3
TEST MODE
P ANEL TEST MODE
This mode is used to check the fl uorescent indicator tube, LEDs, keys, [MASTER VOLUME] jog, [OPERATION DIAL] jog, mod­el, destination and software version.
Procedure:
1. Press [x], button, [METER MODE] button and [DISC SKIP/ EX-CHANGE] button simultaneously.
2. All LEDs and segments in
uorescent indicator tube are light-
ed up.
3. When you want to enter to the software version display mode, press [DISC 1] button. The model information appears on the fl
uorescent indicator tube.
• “GVX 7S” is shown for MHC-GTR88.
Press [DISC 1] button again to view the destination
information.
4. During the destination information display, press [DISC 1] button. Each time [DISC 1] button is pressed, the
uorescent indicator tube shows the version of each category software in the following sequence: SC, MTK (DMB Board
rmware ver­sion), GC, SYS, CD, CDMA, CDMB, ST, TC TA, TM, MTR (METER) and return back to model information display.
5. When [DISC 3] button is pressed while the version numbers are being displayed except model and destination, the date of the software creation appears. When [DISC 3] button is pressed again, the display returns to the software version dis­play. When [DISC 1] button is pressed while the date of the software creation is being displayed, the date of the software creation is displayed in the same order of software version dis­play.
6. Press [DISC 2] button, the key check mode is activated.
7. In the key check mode, the
uorescent indicator tube displays
“K0 V0”.
Each time a button is pressed, “K” value increases. However,
once a button has been pressed, it is no longer taken into ac­count.
“V” value increases in the manner of 0, 1, 2, 3 ... if [MASTER
VOLUME] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if [MASTER VOLUME] knob is turned counterclockwise.
8. When [DISC SKIP/EX-CHANGE] button is pressed after all LEDs and segments in
uorescent indicator tube light up, al-
ternate segments in
uorescent indicator tube and LEDs would light up. If you press [DISC SKIP/EX-CHANGE] button again, another half of alternate segments in
uorescent indi­cator tube and LEDs would light up. Pressing [DISC SKIP/ EX-CHANGE] button again would cause all segments in
uo-
rescent indicator tube and LEDs light up.
9. To release from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
COMMON TEST MODE
This mode is used to check operations of the Amplifi er section.
To enter Common Test Mode Procedure:
1. Press [x], button, [METER MODE] button and [OPEN/ CLOSE] button simultaneously.
2. The CD ring indicators
ash on the fl uorescent indicator tube. The function is changed to AUDIO and the volume is changed to VOLUME MIN.
Check of Amplifi er Procedure:
1. Press [EQ BAND/SURROUND] button repeatedly until a message “GEQ MAX” appears on the
uorescent indicator
tube. GEQ increases to its maximum.
2. Press [EQ BAND/SURROUND] button repeatedly until a message “GEQ MIN” appears on the
uorescent indicator
tube. GEQ decreases to its minimum.
3. Press [EQ BAND/SURROUND] button repeatedly until a message “GEQ FLAT” appears on the
uorescent indicator
tube. GEQ is set to
at.
4. When the [MASTER VOLUME] knob is turned clockwise even slightly, the sound volume increases to its maximum and a message “VOLUME MAX” appears on the
uorescent indi-
cator tube.
5. When the [MASTER VOLUME] knob is turned counterclock­wise even slightly, the sound volume decreases to its minimum and a message “VOLUME MIN” appears on the
uorescent
indicator tube.
To release from Common Test mode
1. To release from this mode, press [
?/1
STANDBY] button.
2. The cold reset is enforced at the same time.
COLD RESET
The cold reset clears all data including preset data stored in the EEPROM to initial conditions. Execute this mode when returning the set to the customer.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [
x
] button, [ENTER] button, and [
?/1
ST ANDBY] but-
ton simultaneously.
3. “COLD RESET” appears on the
uorescent indicator tube.
After that, the
uorescent indicator tube becomes blank for a
while, and the system is reset.
V ACS ON/OFF
This mode is used to switch ON and OFF the VACS (Variable At­tenuation Control System).
Procedure:
1. Press [
?/1
STANDBY] to turn on the system.
2. Press [
x
] button, [RETURN], and [DISPLAY] button simul­taneously. The message “VACS OFF” or “VACS ON” appears on the
uorescent indicator tube.
TUNER STEP CHANGE
The step interval of AM channels can be toggled between 9 kHz and 10 kHz.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [TUNER/BAND] button repeatedly to select the “AM”.
3. Press [
?/1
STANDBY] button to turn off the system.
4. Press [ENTER] button and [
?/1
STANDBY] button simulta­neously. The system turns on automatically . The message “AM 9K STEP” or “AM 10K STEP” appears on the
uorescent in-
dicator tube and thus the channel step is changed.
CD SHIP MODE (WITH MEMORY CLEAR)
This mode moves the optical pick-up to the position durable to vibration and clears all data including preset data stored in the EE­PROM to initial conditions during the next AC-In. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Select CD function.
3. Press [
x
] button, [OPEN/CLOSE] button and [
?/1
STAND­BY] button simultaneously. The system turns off automati­cally.
4. After the “STANDBY” blinking display fi nishes, a message “MECHA LOCK” is displayed on the
uorescent indicator tube
and the CD ship mode is set.
HCD-GTR88
14
CD SHIP MODE (WITHOUT MEMORY CLEAR)
This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Select CD function.
3. Press [DISC SKIP/EX-CHANGE] button and [
?/1
STAND­BY] button simultaneously. The system turns off automati­cally.
4. After the “STANDBY” blinking display
nishes, a message “MECHA LOCK” is displayed on the fl uorescent indicator tube and the CD ship mode is set.
CD TRA Y LOCK MODE
This mode let you lock the disc tray. When this mode is activat­ed, the disc tray will not open when [
Z
OPEN/CLOSE] button or [DISC SKIP/EX-CHANGE] button is pressed. The message “LOCKED” will be displayed on the
uorescent indicator tube.
This mode only applied when there is disc(s) on the tray.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Select CD function.
3. Press [
x
] button and [Z OPEN/CLOSE] button simultane­ously and hold down until “LOCKED” or “UNLOCKED” dis­played on the
uorescent indicator tube (around 5 seconds).
FACT OR Y PRESET
This mode is use to load all the factory use preset frequencies into FM 1-FM 20 and AM 1-AM 10. Originally, frequency of FM 1-FM 20 and AM 1-AM10 are set to the minimum frequency.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [EQ BAND/SURROUND], [x] button, and [DISC 1] button simultaneously and the message “FACTORY” appears on the
uorescent indicator tube. The function is changed to
TUNER automatically.
V ACS DISPLAY
This mode is used to check the VACS level.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [ERASE], [
x
] button and [ENTER] button simultane-
ously.
3. The
uorescent indicator tube displays “V0AP0”.
“V” represents Conventional VACS (Triggered by signal level)
“AP” represents AP VACS (Abuse Protection Variable Attenu­ation Control System)
• To release from VACS display mode
To release from this mode, do the step (2) again.
METER SWITCH TOUCH COUNT DISPLAY
This mode is used to display the total count of meter pointer touch initial switch and max switch.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [x] button, [ENTER] button and [DISPLAY] button si­multaneously.
3. The
uorescent indicator tube displays “IxxxxxMyyyyy”. “I” represents the Initial Switch touch. “xxxxx” represents the total count of Initial Switch touch. (Maximum Value of “xxxxx” = 65535) “M” represents the Max Switch touch. “yyyyy” represents the total count of Max Switch touch. (Maximum Value of “yyyyy” = 65535)
• To release from Meter Switch Touch Count Display Mode.
To release from this mode, do the step (2) again. The
uorescent indicator tube displays “MODE OUT”.
METER TEST MODE
This mode is used to check the meter device.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Press [x] button, [ENTER] button and [METER MODE] but­ton simultaneously.
3. Meter Backlight LEDs, Meter Pointer LEDs, Power Illumina­tor LEDs and
uorescent indicator tube are lighted up.
4. When you want to perform count total step from Initial Switch to Max Switch operation mode, press [
M/>/
TUNING +] button. The meter pointer will move from Initial Switch to Max Switch and
nally move back to the middle position. The
total step count information appears on the
uorescent indica-
tor tube. “xxx STP yy” is shown.
“xxx” represents the total step. (Value of “xxx” should between 430 steps to 470 steps) “yy” represents the status of total step count. (If total step between 430 steps to 470 steps, “yy” is OK, Else
“yy” is NG)
5. When you want to perform count total step from Max Switch to Initial Switch operation mode, press [
m/./
TUNING –] button. The meter pointer will move from Max Switch to Ini­tial Switch and
nally move back to the middle position. The
total step count information appears on the
uorescent indica-
tor tube. “xxx STP yy” is shown.
“xxx” represents the total step. (Value of “xxx” should between 430 steps to 470 steps) “yy” represents the status of total step count. (If total step between 430 steps to 470 steps, “yy” is OK, else
“yy” is NG)
• To release from Meter Test Mode. To release from this mode, do the step (2) again. The fl uorescent indicator tube displays “TST MODE OUT”.
CDM AGING MODE
This mode is used to display the total count of all disc playing.
Procedure:
1. Press [
?/1
STANDBY] button to turn on the system.
2. Select CD function and All DISC play mode.
3. Put discs on all trays and close the tray.
4. Press [GROOVE] button, [
x
] button and [RETURN] button
simultaneously.
5. The
uorescent indicator tube displays Aging Display “AG
xxxx/yyyy”.
“xxxx” represents the error counter (Maximum Value of “xxxx” = 9999) “yyyyy” represents the cycle counter (Maximum Value of “yyyy” = 9999)
6. Press [
m/./
TUNING –] or [
M/>/
TUNING +] to
search for Aging History Error Display
The
uorescent indicator tube displays “Mx E1E2E3E4”. x: error history number E1: Loading sequence JCP high E2: Loading sequence JCP low E3: Loading operation JCP E4: Cam position operation JCP
7. Press [RETURN] to Aging Display
• To release from CDM Aging Mode. To release from this mode, press [
?/1
ST ANDBY] button or
perform COLD RESET operation.
HCD-GTR88
15
SECTION 4
MECHANICAL ADJUSTMENTS
(For African model only) PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened swab :
record/playback head pinch roller erase head rubber belts capstan idlers
2. Demagnetize the record/playback head with a head demag­netizer. (Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
• T orque Measurement
Mode Torque Meter Meter Reading
FWD CQ-102AS
2.0 – 8.0 mN • m (20 to 80 g • cm)
(0.28 – 1.12 oz • inch)
FWD Back T ension CQ-102C
0.15 – 0.6 mN • m (1.5 to 6 g • cm)
(0.021 – 0.083 oz • inch)
FF CQ-201AS
5 – 17.7 mN • m
(50 to 177 g • cm)
(0.7 – 2.48 oz • inch)
REV CQ-201B
5 – 17.7 mN • m
(50 to 177 g • cm)
(0.7 – 2.48 oz • inch)
• T ape Tension Measurement
Mode Torque Meter Meter Reading
FWD CQ-403A
more than 80 g
(more than 2.82 oz)
HCD-GTR88
16
SECTION 5
ELECTRICAL ADJUSTMENTS
FM TUNE LEVEL CHECK
Procedure:
1. Turn the power on.
2. Input the following signal from signal generator to FM antenna input directly.
* Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz Deviation : 75 kHz Modulation : 1 kHz ANT input : 35 dBu (EMF)
Note:
Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and tune A, B and C signals.
4. Con
rm “TUNED” is lit on the display for A, B and C signals.
When mark of “TUNED” means “The selected station signal is received in good condition.”
(For African model only)
1. Demagnetize the record/playback head with a head demagne­tizer.
2. Do not use a magnetized screwdriver for the adjustments.
TEST TAPE
Tape Signal Used for
P-4-A063 6.3 kHz, -10 dB Azimuth Adjustment
RECORD/PLA YBACK HEAD AZIMUTH ADJUSTMENT Procedure:
1. Mode: Playback
set
MIC board PHONES jack (J702)
+ –
level meter
test tape P-4-A063 (6.3 kHz, 10 dB)
TUNER SECTION
FM signal generator
OUT (75 )
SET
DECK SECTION
0dB = 0.775V
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
Screw position
L-CH peak
within 1 dB
Output level
L-CH peak
R-CH peak
within 1 dB
Screw position
R-CH peak
3. Mode: Playback
set
test tape P-4-A063 (6.3 kHz, 10 dB)
oscilloscope
V
H
waveform of oscilloscope
in phase 45q 90q 135q 180q
good
wrong
MIC board PHONES jack (J702)
4. After the adjustments, apply suitable locking compound to the pats adjusted.
Adjustment Location:
Record/Playback/Erase Head
HCD-GTR88
HCD-GTR88
1717
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM - RF SERVO, USB Section -
REC/PLAY B
OPTICAL PICK-UP
BLOCK
(KHM-313CAB)
RF AMP, SERVO DSP,
AUDIO PROCESSOR
IC101
SYSTEM
CONTROLLER
IC401 (1/4)
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC201
AUTOMATIC POWER
CONTROL
Q102-1
RF_IP 125
RF_C 3
RF_B2RF_A1RF_D
4
RF
VOA/A
VOB/B
VOC/C
VOD/D
RF_F6VOE/E+G
RF_E5VOF/F+H
V2O12VC
LDO117LD (780)
AUTOMATIC POWER
CONTROL
Q102-2
LDO2 18LD (650)
FOO25
CD ON
SWITCH
Q101-1
CD ON
SWITCH
Q101-2
VR (780)
MSW
GPIO
23
118
VR (650)
FCS+
MSW
MDI115
MDI216
PD
LIMIT SW
Q103
SF_CS#CS_
SD-RAM
IC104
X101
27MHz
36
FCS– 37
1
TRO24
TRK+ 35
TRK– 34
4
FMO21
SL+ 29
SL– 30
10
DMO20
SP+ 27
SP– 28
31
32
41
46
47
13
SPFG/OPINN128
45
GPIO
GPIO
GPIO
120
DG0, DQ1 – DQ15
RD0 – RD15
A0 – A11
RA0 – RA11
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
45 – 49, 51 – 53,
64 – 61, 56 – 59
82, 83, 85, 86,
74 – 69, 81, 67
23 – 26,
29 – 34, 22, 35
36
XTALI
9
1
SF_CKSCK
39
6
BA0 BA0
78
20
BA1 BA1
80
21
RCLK CLK
66
38
DQM0 LDQM
55
15
DQM1 UDQM
65
39
RAS# RAS
77
18
CAS# CAS
76
17
RWE# WE
75
16
: CD PLAY
: AUDIO
: USB
FOCUS
COIL DRIVE
TRACKING
COIL DRIVE
SLED
MOTOR DRIVE
SPINDLE
MOTOR DRIVE
REGULATOR
GPIOMUTE123 11619
6
7
MUTE4MUTE4 2220GPIOTSD-M 9422IOPMON/
OPINP
127
40
8
PS
21
BUFFER
BUFFER
RF +3.3V
REGO2
REGO1
REGO2
REGO1
FLASH ROM
IC102
XTALO
10
L-OUT
115
119
GPIO
114
GPIO19
106
VINL
14
13
VINR
BCK
7
LRCK
6
8
SCKI
A/D CONVERTER
IC4601
9
DOUT
R-CH
USB CONTROLLER
IC1501
31
USBUP_DP
30
USBUP_DM
AOUT-L
5
8
AOUT-R
D/A CONVERTER
IC4602
1
SDATA2SCLK3LRCK4ACLK
USB_DP 27
R-CH
USB_DM 28
SO
2
SI
5
SF_DO
37
SF_DI
38
PRST#
43
CD MECHANISM
DECK
M1-
M2+
M2-
M1+
M1+
23
M1- 25
M2+
24
M2- 26
MOTOR
DRIVE
Q645 - 648
MOTOR
DRIVE
Q640, 641,
Q643, 644
SW3
SW2
SW7-CHACK
SW1
SW1
21
SW3
22
SW2
18
SW-CHUCK
19
SW5-STOCK
SW8-OPEN
SW6-CLOSE
SW-STOCK
6
SW-CLOSE
7
SW-OPEN 5
2USBDN1_DP
1USBDN1_DM
50MTK-OC2
CN1001
3
2
1
D+
D–
47MTK-OC1
VBUS
VBUS OVER
CURRENT DETECT
IC1500
4USBDN2_DP
3USBDN2_DM
3
2
1
D+
D–
VBUS
MTK-RST38
MTK-TXD35MTK-RXD36MTK-CLOCK37MTK-XIFCS
34
MTK-BUSY 39
IFSDI
35
IFSOD
41
IFSCK
40
IFCS#
88
IFBSY
87
HUB_RST45
VBUS_DET 44
VBUS_DET27RESET_N
26
X1500
24MHz
XTAL1/
CLKIN
33
XTAL2
32
USB +5V
PLAY A
CN1000
SIGNAL PATH
R-CH is omitted due to same as L-CH.
OPOUT126
1
7
3
5
A
(Page 18)
B
(Page 18)
USB RECORD PREAMP
7 5
IC251
HCD-GTR88
HCD-GTR88
1818
6-2. BLOCK DIAGRAM - MAIN Section -
R-CH
TUNER (FM/AM)
AM
FM ANT
AM ANT
ST-L
ST-R
ST-DOUT
R-CH
R-CH
(E4)
R-CH
ST-DIN
ST-CLK
ST-CE
FM 75
:
COAXIAL
ANTENNA
TUNED
54 ST-TUNED
43 ST-L
56 ST-R
42 TAPE L
1 TAPE R
R-CH
3 CD-R
36 REC BL
7 REC BR
21
DATA
22
CLK
44
30
PC-L
46 MIC
29 VOLINLTONEOUTL 26
(SW OUTL)
R-CH
55 PC-R
40
CD-L
46 ST-DOUT
51 ST-CLK
53 ST-CE
R2A15216FP-DATA
58
TC REC MUTE
41
TC STATE
72
9
SA2
POWER ILLUMINATOR
69
VACS IN
70
R2A15216FP-CLK
57
HP/MIC DET
66
25
20
AGC OUTL
(SW OUTR)
AGC OUTR
OUTL
6
RECAR
28BB1L
37RECAL
BAND-PASS
FILTER
Q210
271917
18
BB2L
BB2R
BB1R
OUTR
BASS AGC
Q128
BASS AGC
Q178
D104
D201
D116
INPUT SELECTOR,
ELECTRICAL VOLUME
IC400
SYSTEM CONTROLLER
IC401 (2/4)
: AUDIO
SIGNAL PATH
R-CH is omitted due to same as L-CH.
: TUNER (FM/AM)
J700
MIC
RV700
MIC LEVEL
IC700 MIC AMP
52 ST-DIN
PC_R
PC_L
J020
PC IN
L-OUT
REC-L
HP DET
OUT
SW OUT
BASS AGC
: MIC
: TAPE (PLA Y)
: TAPE (REC)
R-CH
R-CH
R-CH
1375
R-CH
Q063
57
R-CH
L501
S501
IC502
IC501
OP AMP
OP AMP
MUTE
SW
Q062
MUTE
SW
BIAS OSC
Q501, 502
R-CH
EH
VREF
SW
L-CH
TAPE DECK
A
(Page 17)
13X-OUT
15X-IN
X402
8MHz
11XC-OUT
10XC-IN
X401
32.768kHz
Abbreviation
E4 : African model
C
(Page 19)
B
(Page 17)D(Page 19)
E
(Page 19)F(Page 19)
G
(Page 20)
75
HCD-GTR88
HCD-GTR88
1919
6-3. BLOCK DIAGRAM - AMP Section -
R
L
SW PREAMP
IC255
75
SW PREAMP
IC254
75
SW PREAMP
IC253
75
FR PREAMP
IC252
POWER
AMP
IC1300
IC800
AMP
POWER
MUTING
Q270
OVER LOAD
DETECT
Q1301
OVER LOAD
DETECT
Q1300
OVER LOAD
DETECT
Q850
OVER LOAD
DETECT
Q800
R-CH
MUTING
Q245
MUTING
CONTROL
Q290
MUTE
Q1309, Q1308
LINE MUTE
63
STK MUTE
PROTECT
CONTROL
FAN HIGH SPEED
60
16
15
11
6
4
18 11
SW SPK RELAY
48
FAN MOTOR
DRIVE
Q602
RY1300
+
+
RY862
D1036
TH1301
M
M101
(DC FAN)
M
M101
(DC FAN)
PHONES
SUBWOOFER
RELAY
DRIVE
Q031
FR SPK RELAY
43
RELAY
DRIVER
Q032
FAN SW
Q600
R-CH
J702
SYSTEM CONTROLLER
IC401 (3/4)
: AUDIO
SIGNAL PATH
R-CH is omitted due to same as L-CH.
DC
DETECT
Q1302, Q1303
THERMAL
DETECTOR
Q1305, Q1307
R
L
FRONT
SPEAKER
TB1300
+
+
R
L
SATELLITE
SPEAKER
TB1301
59
BASS AGC
HP DET
OUT
SW OUT
RELAY
DRIVER
Q030
MUTING
Q220
14 8
C
(Page 18)
F
(Page 18)
D
(Page 18)
E
(Page 18)
+–+
TB801
H
61
13
MUTING
Q295
PROTECT
DETECT
Q1304, 1306
(Page 20)
R-CH
R-CH
R-CH
R-CH
R-CH
RELAY
DRIVER
Q033
HCD-GTR88
HCD-GTR88
2020
6-4. BLOCK DIAGRAM - DISPLAY, POWER SUPPLY Section -
54
REMOTE CONTROL
RECEIVER
IC1100
FL1100
FLUORESCENT
INDICATOR
TUBE
94 SW/USB CTRL
FLUORESCENT INDICATOR
TUBE DRIVER
IC1101
SYSTEM CONTROLLER
IC401 (4/4)
RECT
D1201, 1202
LED-VOL1. 2
LED-VOL3. 4
LED-VOL5. 6
S1100 – 1109,
S1110 – 1119,
S1124 – 1133,
S1302
75STBY RELAY
RESET SWITCH
Q350, 351
D351
D571
D+3.3V
+1.8V
71OVERVOLTAGE
20AC CUT
12RESET
87 MASTER VOL
SG5/KS5 –
SG24/KS24
14 – 33
D1105 – 1107, SEL A
D1108 – 1110, SEL B
(STREAM)
LED DRIVE
Q1122
86 USB-LED CTRL
LED DRIVE
Q1121
D1104
SUBWOOFER
95 STBY LED
AD KEY0
4 SIRCS
D1011
I/
1
STANDBY
ROTARY
ENCODER
MASTER
VOLUME
S1301
DIN
FL-DRIVER-DATA2 2
CLK
FL-DRIVER-CLK1 1
STB
FL-DRIVER-CS3 100
889190
749789
85
POWER/DISPLAY-KEY
AD-KEY0
AD-KEY1
AD-KEY2
(AC IN)
RY1200
RELAY
DRIVE
Q1200
VOLTAGE
SELECTOR
S1200
FAN
+12V
D1250
M+9V
F1254
RECT
D600
F1252
F1253
F1250
F1251
RECT
D1300
LED+9V
+4V
REGULATOR
Q352-354
LED SEL A,
LED SEL B
CD MOTOR B+
REGULATOR
Q655 – 658
27
2 1
CDM-SD
JOG B+
3AD SUPPLY SW
B+ SWITCH
Q400, 500
–32V
REGULATOR
Q1250
AMP
SECTION
B+
FOR
FLUORESCENT
INDICATOR
TUBE
–VG
VF
VF
PT1200
SUB POWER
TRANSFORMER
PT1250
MAIN POWER
TRANSFORMER
VCC +3.3V
EVER +3.3V
+VH
–VH
D1002, 1003
(E2, E51, E4)
(MX, AR, AUS)
AC DETECT
GR1 – GR14
34 – 47
LED DRIVE
Q1118 – 1120
USB B
D1000
USB A
+5V
REGULATOR
IC065
49MTK OE
USB +5V
M +5V
+5V
REGULATOR
Q360
B+ SWITCH
Q300 – 303
82
METER PTR
LED
METER
DISPLAY
BLOCK
AC CUT
DETECTOR
D1203
83 METER BL CTL
LED DRIVE
Q230
LED SEL A
LED SEL B
LED
LED DRIVE
Q582
81 METER SW
77 METER-IN4
78 METER-IN3
80 METER-IN2
METER-IN179
+9V
SWITCH
Q684
M+9V
(E4)
RECT
D1301
+VL
–VL
POWER
CONTROL
Q090
SW DRIVER
Q681
76TC_M+9V SW
+12V
REGULATOR
IC040
M+9V
UNREGULATE
H
Abbreviation
AR : Argentina model
E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian models
MX : Mexican model
AUS : Australian model
12
D623, 624
A+9V
AVDD +5V
DVDD +5V
RF+3.3V
+5V
REGULATOR
Q696
2
1
3.3V REGULATOR
IC107
F1255
(Page 19)
G
(Page 18)
+9V
REGULATOR
IC055
I
O
+3.3V
REGULATOR
IC075
+9V
REGULATOR
IC200
21
+1.8V
REGULATOR
IC111
81
HCD-GTR88
HCD-GTR88
2121
• Circuit Boards Location
For Schematic Diagrams.
Note:
• All capacitors are in F unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in and 1/4 W or less unless otherwise
specifi ed.
f
: Internal component.
2 : Nonfl ammable resistor.
5 : Fusible resistor.
C : Panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMA TIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
A : B+ Line.
B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
- TC Board -
no mark : TAPE PLAY
( ) : TAPE REC
- Other Boards -
no mark : TUNER (FM/AM)
( ) : CD PLAY
<< >> : TAPE PLAY
[ ] : TAPE REC
< > : USB
{ } : PC
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : AUDIO
f : TUNER (FM/AM)
E : TAPE PLAY
G : TAPE REC
N : MIC
J : CD PLAY
c : DIGITAL
I : USB
• Abbreviation
AR : Argentine model
AUS : Australian model
E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian models
MX : Mexican model
For Printed Wiring Boards.
Note:
X : Parts extracted from the component side.
Y : Parts extracted from the conductor side.
f
: Internal component.
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
• Indication of transistor.
C
B
These are omitted.
E
Q
CEB
These are omitted.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note:
The components identifi ed by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specifi ed.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Abbreviation
AR : Argentine model
AUS : Australian model
E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian models
MX : Mexican model
• DMB19 board is multi-layer printed board.
However, the patterns of intermediate layers have not
been included in diagrams.
TRANS board
PT SHIELD board
POWER AMP board
MAIN board
SUBWOOFER board
SUBTRANS board
DMB19 board
HUB board
LED (GVX) board
included in METER DISPLAY ASSY
VOL board
USB board
MIC board
DISPLAY board
TUNER (FM/AM)
SW (GVX) board
included in METER DISPLAY ASSY
MOTOR DRIVE board
included in METER DISPLAY ASSY
TC board
(For African model only)
HCD-GTR88
HCD-GTR88
2222
6-5. PRINTED WIRING BOARD - DISPLAY Board -
: Uses unleaded solder.
• See page 21 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10 11 14 1512 13
A
B
C
D
E
F
G
H
I
J
2
22
1
23
CN1105
C1136
C1147
C1155
VCC
O
IC1100
1 3
CN1103
1 4
CN1102
S1100
S1101S1102
S1103
S1104
S1105
S1106 S1 107
S1108
S1110
S1111
S1112
S1113
S1114
S1115
S1116
S1117
S1118
S1119
S1124
S1125
S1126
S1127
S1128
S1129
S1130
S1131
S1132
S1133
D1104
D1101
D1107
D1106
D1105
D1110
D1109
D1108
C1137
12 54535 503118
DISPLAY BOARD
E
Q1118
E
Q1119
E
Q1120
E
Q1121
E
Q1122
D1102
1
52
13
14
26
27
39
40
IC1101
TP0001
TP0093
TP0070
TP0009
TP0105
TP0099
TP0081
TP0063
TP0033
TP0012
TP0108
TP0083
TP0075
TP0057
TP0023
TP0007
TP0103
TP0098
TP0080
TP0062
TP0019
TP0006
TP0102
TP0097
TP0072
TP0018
TP0014
TP0109
TP0084
TP0065
TP0058
TP0024
TP0008
TP0104
TP0073
TP0032
TP0002
FL1100
TP0094
TP0089
TP0060
TP0010
TP0106
TP0074
TP0034
TP0020
TP0092
TP0088
TP0079
TP0069
TP0026
TP0004
TP0100
TP0095
TP0071
TP0027
TP0016
TP0111
TP0091
TP0086
TP0077
TP0066
TP0015
TP0110
TP0085
TP0076
TP0059
TP0096
TP0005
TP0101
TP0061
TP0017
TP0112
TP0087
TP0078
TP0068
TP0011
TP0107
TP0090
TP0082
TP0064
TP0022
R1203
R1198
R1160
R1116
R1106
C1151
R1166 R1174
R1173
R1120
R1101
R1168
R1211
R1164
R1100
R1210
R1163
R1119
C1153
R1103
R1215
R1170
R1165
R1158
R1205
R1199
R1117
R1107
R1171
R1167
R1201
R1196
R1115
R1105
R1207
R1161
R1108
C1152
R1190
R1113
R1104
R1189
R1209
R1162
R1118
R1195
R1169
R1114
C1150
R1121
R1102
C1156
JR
JR1001
JR
JR1002
JR
JR1004
JR
JR1005
JR
JR1006
JR
JR1007
JR
JR1008
JR
JR1011
JR
JR1012
JR
JR1016
JR
JR1017
JR
JR1018
JR
JR1019
JR
JR1020
JR
JR1021
JR
JR1022
JR
JR1023
JR
JR1024
JR
JR1025
JR
JR1026
JR
JR1027
JR
JR1028
JR
JR1032
JR
JR1009
JR
JR1013
JR
JR1029
JR
JR1030
JR
JR1031
JR
JR1033
JR
JR1003
JR
JR1034
JR
JR1015
JR
JR1035
JR
JR1036
JR
JR1014
VOL BOARD
NO1103
(Page 34)
K
S1109
MAIN BOARD
CN405
(Page 30)
N
USB BOARD
NO1000
(Page 34)
L
DISC SKIP/
EX-CHANGE
ERASE
EQ BAND/
SURROUND
GROOVE
SUBWOOFER
PRESET EQ
1-881-085-
12
(12)
REC TIMER
DISC 3
USB A
USB B
RETURN
USB
CD
ENTER
TAPE/PC
TUNER
BAND
REC TO
USB B
DISC 2
DISC 1
OPTIONS
METER
MODE
DISPLAY
OPEN/CLOSE
TUNING +
TUNING -
STANDBY
+
-
"/1
HCD-GTR88
HCD-GTR88
2323
• See page 43 for Waveforms. • See page 44 for IC Block Diagrams. • See page 48 for IC Pin Function Description.
6-6. SCHEMATIC DIAGRAM - DISPLAY Board -
1 2 3 4 5 6 7 8 9 10 11 14 1512 13
A
B
C
D
E
F
G
H
I
J
DISPLA Y BOARD
MAIN
BOARD
(1/3)
CN405
(Page 31)
N
VOL
BOARD
NO1103
(Page 35)
K
0.1
C1156
10V
47
C1155
10k
R1201
10k
R1203
10k
R1205
TP0075TP0074TP0073
680
R1195
680
R1199
680
R1196
680
R1198
100
R1210
TP0009
TP0010
TP0011
TP0012
TP0014
TP0015
TP0016
TP0017
TP0018
TP0019
TP0020
TP0022
TP0008
TP0007
TP0005
TP0006
TP0032
TP0034
2SC3052EF-T1-LEF
Q1120
2SC3052EF-T1-LEF
Q1118
2SC3052EF-T1-LEF
Q1119
TP0033
47k
R1160
TP0002
TP0004
1k
R1173
1k
R1174
10k
R1171
2SC3052EF-T1-LEF
Q1122
C1152
100p
123
3P
CN1103
DGND
DET SWITCH
VOL
47k
R1158
50V
2.2
C1136
2SC3052EF-T1-LEF
Q1121
TP0058
TP0060
TP0059
10k
R1207
680
R1162
4.7k
R1168
10k
R1170
1.5k
R1165
2.2k
R1166
1k
R1163
1.5k
R1164
3.3k
R1167
6.8k
R1169
123
4
4P
CN1102
SW/USB_LED
LED SEL B
LED SEL A
USB LED CTRL
TP0057
TP0062
TP0066 TP0065 TP0064 TP0063
100k
R1215
TP0061
C1151
100p
100
R1209
0.1
C1150
TP0068
100
R1211
C1153
100p
TP0069
TP0070
TP0023
TP0024
680
R1100
10k
R1108
680
R1113
1.5k
R1116
1.5k
R1115
1k
R1114
1.5k
R1103
1.5k
R1102
2.2k
R1104
4.7k
R1106
1k
R1101
6.8k
R1107
3.3k
R1105
SLR-325MCT31
D1104
4.7k
R1119
3.3k
R1118
6.8k
R1120
10k
R1121
2.2k
R1117
TP0001
VCC
OUT
GND
PNA4823M03S0
IC1100
FL1100
156789101112131415161718313233343536373839404142434445464748495054 253
12345678910111213
1516171819202122232425
26
2930313233343536373839
434445464748495051
52 14
28
414240
27
PT6324-Q
IC1101
CLK
DIN
STB
DOUT
K1
K2
OSC
GND
VDD
SG1/KS1
SG2/KS2
SG3/KS3
SG4/KS4
SG6/KS6
SG7/KS7
SG8/KS8
SG9/KS9
SG10/KS10
SG11/KS11
SG12/KS12
SG13/KS13
SG14/KS14
SG15/KS15
SG16/KS16
SG17/KS17
SG18/KS18
SG20/KS20 SG21/KS21 SG22/KS22 SG23/KS23
SG24/KS24 GR1 GR2 GR3 GR4 GR5 GR6
GR7
GR10
GR11
GR12
GR13
GR14
GR15
GR16
VEE
VDD
GND
SG5/KS5
SG19/KS19
GR8
GR9
123
13
12910
7
14
222320
648
15
1921181716
5
11
23P
CN1105
SEL B
SEL A
LED GND
EVER +3.3V
STBY LED
LED3
LED2
LED1
SIRCS
FL-CLK
FL-DATA
FL-CS
VOL
AD KEY2
AD KEY1
AD KEY0
FL+3.3V
DGND
VF
-VG
VF
USB LED CTRL
SW/USB_LED
TP0026
TP0027
D1107
50V
22
C1147
SLI-325URT31WR
D1101
1k
R1161
MAZ8082GMLS0
D1102
50V
2.2
C1137
D1110 D1109 D1108 D1106 D1105
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S12
S13
S14
S15
S16
S17
S18
S19
S20
SW_LED
LED_VOL1.2
LED_VOL3.4
LED_VOL5.6
G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14
FL_CLK
S1
S2
S6
S7
S8
S9
S10
S11
S12
S13
S3S4S5
G2 G3 G4 G5 G6
G7G8G9
G10
G11
G12
G13
G14
S11
S14
S15
S16
S17
S18
S19
S20
AD_KEY1
AD_KEY0
AD_KEY1
AD_KEY2
VOL
FL_CS
FL_DATA
FL_CLK
SIRCS
LED_VOL5.6
LED_VOL3.4
LED_VOL1.2
SW_LED
G1
AD_KEY2
VOL
FL_DATA
FL_CS
SIRCS
AD_KEY0
S1110 S1111 S1112 S1113 S1114 S1115 S1116 S1117 S1118 S1119
IC1101
FLUORESCENT INDICATOR
IC1100
REMOTE CONTROL
FLUORESCENT INDICATOR TUBE
RECEIVER
LED DRIVELED DRIVELED DRIVE
LED DRIVELED DRIVE
D1105-1110
1L0351V22F0MIT01
STREAM
/
STANDBY
STANDBY
/
MODE
METER
DISPLAY OPTIONS GROOVE
OPEN/CLOSE
DISC SKIP/
EX-CHANGE
USB B
TUNER/
BAND
TAPE/PCCD
TUNING -
USB
TUNING +
SUBWOOFER
TUBE DRIVER
680
R1189
680
R1190
132
ENTER RETURNUSB A DISC 3 DISC 2 DISC 1
REC TO
USB B
S1124S1128 S1127 S1125S1126 S1130S1132 S1131 S1129S1133
PRESET
EQ
ERASE
SUBWOOFER
EQ BAND/
SURROUND
REC
TIMER
S1100 S1102 S1103S1101 S1109S1108 S1107 S1106 S1104S1105
USB
BOARD
NO1000
(Page 35)
L
2.9 0.8 2.6 1.8 3.3
-30.6
-26.4
-32.7
-32.7
-26.3
-22.1
-24.2
-24.2
-20.0
-24.3
-29.8
-32.7
-26.5
-31.0
-31.0
-31.0
-31.0
-31.0
-31.0
-31.0
-31.0
-33.2
3.3
-24.4
-32.9
-30.8
-26.5
-22.3
-26.5
-24.4
-31.0
-31.0
-31.0
-31.0
-31.0
-31.0
3.5
3.5
6.0
0.1
6.0(2.1)<<2.1>>
0.1(0.5)
<<0.5>>
7.4
0
7.5
0
8.3
0
IC B/D
- +
HCD-GTR88
HCD-GTR88
2424
6-7. PRINTED WIRING BOARD - DMB19 Board -
Note:
When IC102 cannot exchange with single. When this part
is damaged, exchange the entire mounted board.
: Uses unleaded solder.
• See page 21 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10 11 14 1512 13
A
B
C
D
E
F
G
H
I
J
DMB19 BOARD (COMPONENT SIDE) DMB19 BOARD (CONDUCTOR SIDE)
1-881-688-
21
(21)
1-881-688-
21
(21)
1
12
13
48
24
25
36
37
IC201
IC4601
IC4602
IC107
R1177
C144
C156
IC111
R4833
R4834
C4603
C4606
C4602
R4606
R4605
R4602
R4608
R4609
R4611
C4623
C4622
C502
C4626
R521
R606
IO
FL603
FB603
C215
R233
C212
C214
R226
C211
R220
C233
R212
R225
R221
C209
R223
C219
C224
R608
R234
R214
C205
R208
R215
C206
R209
C203
R204
R205
R213
R216
R207
R206
C208
R210
E1
E
E2
R115
R112
R113
R120
R121
R118
R109
R110
R123
R256
R124
Q103
Q102
S2
S1
Q101
R116
R117
R111
R108
R1129
C149
FB108
C179
C180
C191
C181
R122
C1505
R125
C155
C125
R1255
C111
C115
C116
C119
C168
C169
R1101
C172
R1150
C150
C175
C151
R1193
R1191
R1194
R1192
R1252
C102
R219
C213
R224
C210
R136
R1184
C195
C192
C193
C154
C145
C146
C127
C126
C108
C1506
C198
C183 R1178
C188
R4835
D005
R1261
R133
C197
R1250
FB1268 FB1267
R1262
R101
C1507
C199
C221
C222
C1512
C1513
R1256
R630
R1278
R1279
R1280
IC102
X101
IC101
1
5
1
9
CN601
CN101
CN4602
R103
C603
C1504
C604
RB105
R605
CN1105
CN105
C105
RB106
RB107
R107
RB108
C4608
C608
1
13
R1110
RB111
C112
R1114
C217
C118
R1121
R1123
C124
R142
R246
R247
R1248
R1249
C152
C153
R156
C160
R1168
C190
CN201
C623
D004
C622
D003
D002
C621
D001
C620
C611
R231
R230 R232
C216
C101
R102
C602
RB112
RB113
RB114
RB115
R1263
R1151
R1152
R1269
R114
C106
C113
CN1106
FB1264
R4837
R4838
IC104
R1277
R1276
ET004
FB1265 FB1266
ET001
ET002
ET003
R4601
C218
C220
C1514
C1515
C1516
R1281
R1282
R1283
MAIN BOARD
CN090
(Page 30)
S
MAIN BOARD
CN680
(Page 30)
R
DEVICE, OPTICAL
KHM-313CAB/C2RP
HUB BOARD
CN1500
(Page 41)
Q
DEVICE, OPTICAL
KHM-313CAB/C2RP
FOR TEST
MAIN BOARD
CN690
(Page 30)
T
FB607
Loading...
+ 53 hidden pages