PR/CR: 0.7 Vp-p, 75 ohms
S VIDEO OUT:Y: 1 Vp-p, unbalanced,
(4-pin/mini-DIN jack)Sync. negative
C: 0.286 Vp-p load impedance 75 ohms
PHONES:accepts headphones of
(stereo mini jack)8 ohms or more
FRONT SPEAKER:Use only the supplied speakers
SURR SPEAKER:Use only the supplied speakers
CENTER SPEAKER:Use only the supplied speaker
SUBWOOFER OUT:Voltage 250 mV
(phono jack)impedance 1 kilohm
(with the interval set at 10 kHz)
AntennaAM loop antenna
Antenna terminalsExternal antenna terminal
Intermediate frequency450 kHz
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
This appliance is classified as
a CLASS 1 LASER product.
This label is located on the rear
exterior.
General
Power requirements
Australian model:230 – 240 V AC, 50/60 Hz
Saudi Arabian model:120 – 127 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage selector
Other models:120 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage selector
Power consumption
MHC-GNV111D380 W
MHC-GNV99D285 W
Dimensions (w/h/d) (Approx.)
HCD-GNV111D280 × 371 × 398.5 mm
HCD-GNV99D280 × 360 × 398.5 mm
Mass (Approx.)
HCD-GNV111D16.1 kg
HCD-GNV99D15.2 kg
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
8-4. DVD Mechanism Section-1 (CDM74H-DVBU101) ...... 76
8-5. DVD Mechanism Section-2 (CDMm74H-DVBU101) ... 77
9.ELECTRICAL PARTS LIST ....................... 78
3
Page 4
HCD-GNV99D/GNV111D
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output several times.
NOTE ON REPLACEMENT OF DMB10 BOARD
New part of EEPROM (IC103) on the DMB10 board can not be
used. Therefore, if the mounted DMB10 board (A-1099-272-A or
A-1099-344-A or A-1115-347-A) is replaced, exchange new
EEPROM with that used before the replacement.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears in
the on-screen display and the front panel
display. In this case, check the following table.
First 3
characters of
the service
number
C 13The disc is dirty.
C 31The disc is not inserted correctly.
E XX
(xx is a number)
Cause and/or corrective action
•Clean the disc with a soft cloth
(page xx).
•Restart the system, then re- insert
the disc correctly.
To prevent a malfunction, the
system has performed the selfdiagnosis function.
•Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5character service number.
Example: E 61 10
This section is extracted
from instruction manual.
How to use page 106 to 108
Use this page to find the location of buttons and other
parts of the unit and remote that are mentioned in the
text.
Unit
ALPHABETICAL ORDER
A – D
AMP MENU ef
AUTO/MANUAL
CD SYNC qd
Deck A es
Deck B ws
DIRECTION qk
DISC 1 ~ 3 7
Disc tray 9
DISPLAY rf
Display rg
DVD r;
E – L
ECHO LEVEL wf
ENTER wa
EQ BAND qa
EX-CHANGE/DISC SKIP 6
GROOVE ej
ILLUMINATION rd
IR Receptor ra
*
2
SYMBOLS
?/1 (power) rs
Z OPEN/CLOSE 5
nN (play) qs
.> (go backward/forward)
mM (rewind/fast forward)
X (pause) qf
x (stop) qg
Z A (Eject A) ed
B Z (Eject B) w;
*MHC-GNV111D only
Top Panel
on number
r
TAPE A/B ek (63–65, 75, 78, 79)
Name of button/part Reference page
SLOW ql
RR
qj
ql
23
1
4
M – R
MASTER VOLUME 8
MIC 1 (jack) wj
MIC 2 (jack) wh
MIC LEVEL wg
OPERATION DIAL e;
PHONES (jack) wl
Power illuminator wd
PRESET +/– qj
PROGRESSIVE q;
REC PAUSE/START qh
S – Z
SOUND FIELD rh
SOUND FLASH ea
SPEAKERS
TAPE A/B ek
Tape lid wses
TUNER/BAND el
TUNING +/– ql
TV/SAT eh
VIDEO INPUT (jacks) wk
VIDEO eg
X-ROUND buttons
X-ROUND JOG
X-ROUND OFF
*
1
*
*
*
3
41
WAVE/FADER/BALANCE/
RANDOM/TWISTER
Front Panel
rh
rg
rf
rd
rs
ra
r;
el
ek
ej
eh
eg
ef
ed
es
ea
e;
8
0
qs
qf
qh
qk
w;
ws
9
qa
qd
qg
qj
ql
wz
wd
6
wkwgwhwjX
wl
Page 7
Remote control
HCD-GNV99D/GNV111D
This section is extracted
from instruction manual.
ALPHABETICAL ORDER
A – L
ADVANCE wd
ALBUM +/– qa
ANGLE q;
AUDIO 8
CLEAR wj
DISC SKIP 3
DISPLAY es
ENTER wg
FM MODE 7
FUNCTION +/– 4
KARAOKE MODE e;
KARAOKE PON wl
KEY CONTROL #/2 ea
M – S
MENU qs
Numeric Buttons
PICTURE NAVI 6
PRESET + qg
PRESET – ws
REPEAT 7
REPLAY wd
SLEEP ef
SLOW qh
SLOW wa
SOUND FIELD 5
STEP C wd
SUBTITLE 9
T – Z
THEATRE SYNC 1
TIMER MENU eg
TIME/TEXT ed
TOP MENU wh
TUNING + qh
TUNING – wa
2)
ql
TV
TV CH +
TV CH –
TV/VIDEO
TV VOL +/–
TV &/1
VOLUME +/–
2)
qg
2)
ws
2)
ef
1)2)
2)
2
1)2)
wk
qd
1)
qd
NUMBERS AND SYMBOLS
?/1 (power) 2
x (stop) qj
X (pause) qk
1)
(play) w;
H
> (go forward) qg
. (go backward) ws
M (fast forward) qh
m (rewind) wa
M/m/</, wg
2)
wk
10/0
2)
-/--
wj
O RETURN wf
DISPLAY qf
c STEP wd
1)
The numeric button 5, TV VOL +, VOLUME + and
H buttons have a tactile dot. Use the tactile dot as
a reference when operating the system.
2)
This button is used to operate a Sony TV. For
details, see “Operating a Sony TV” on page 12.
ef
es
e;
wk
wh
wf
ws
w;
eg
ed
ea
wl
wj
wg
wd
wa
ql
1
3
5
7
9
qa
qd
qg
qj
2
4
6
8
q;
qs
qf
qh
qk
Setting the clock
1
Press ?/1 to turn on the system.
2
Press TIMER MENU.
The hour indication flashes in the display.
3
Press M or m repeatedly to set the hour.
4
Press ENTER.
The minute indication flashes in the
display.
5
Press M or m repeatedly to set the
minute.
6
Press ENTER.
The clock starts functioning.
To adjust the clock
1
Press TIMER MENU.
“PLAY SET?” flashes in the display.
2
Press M or m repeatedly to select “CLOCK
SET?”, then press ENTER.
The hour indication flashes in the display.
3
Do the same procedures as step 3 to 6
above.
Notes
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
You cannot set the clock in power saving mode
.
7
Page 8
HCD-GNV99D/GNV111D
Note:
• The illustration depicts HCD-GNV111D.
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. CASE
(Page9)
SECTION 3
DISASSEMBLY
3-3. LOADING PANEL ASSY
(Page9)
3-4. FRONT PANEL ASSY
(Page10)
3-5. TUNER PACK
(Page11)
3-8. DVD MECHANISM DECK
(Page14)
3-10. BACK PANEL
(Page16)
3-6. TAPE MECHANISM DECK,
MIC BOARD
3-9. VIDEO BOARD,
DMB10 BOARD
3-15. DRIVER BOARD,
(P
age12)
(Page15)
SW BOARD
(Page18)
3-7.PANEL BOARD,
CD-SW BOARD
(Page13)
3-16. DVD ASSY
(Page19)
3-18. SENSOR BOARD
(Page20)
3-12. POWER AMP PC BOARD ASSY,
MAIN BOARD
3-13. DVD SURR BOARD,
PA BOARD
(P
(P
age17)
age17)
8
3-11. PRIMARY BOARD
(Page16)
3-17. OPTICAL PICK-UP
(Page19)
3-14. POWER TRANSFORMER
(T1200)
(Page18)
3-19. MOTOR (TB) BOARD
(Page20)
3-20. MOTOR (LD) BOARD
(Page21)
Page 9
)
3-2. CASE
4
screw
(case 3 TP2)
(3
3
two screws
(case 3 TP2)
(3
´
8)
HCD-GNV99D/GNV111D
5
three screws
(+BVTP 3
CASE
7
´
12)
6
´
10)
2
screw
(case 3 TP2)
(3
´
12)
6
four screws
(+BVTP 3
´
10
3-3. LOADING PANEL ASSY
DVD mechanismdeck (CDM74H-DVBU101)
1
Turn the pulley to the arrow direction.
Pulley
1
two screws
(case 3 TP2)
´
8)
(3
loading panel assy
4
Front side
2
Pull out disc tray
3
9
Page 10
HCD-GNV99D/GNV111D
3-4. FRONT PANEL ASSY
4
screw
(+BVTP 3
´
10)
qa
flat wire
(CN509)
0
flat wire
(CN508)
3
screw
(+BVTP 3
qs
connector
(CN100)
´
10)
qd
(CN802)
lug
connector
6
front panel assy
2
two screws
(+BVTP 3
7
connector
(CN1102)
5
screw
(+BVTP 3
8
connector
9
connector
(CN503)
´
10)
1
two screws
(+BVTP 3
´
10)
(CN504)
´
6)
10
Page 11
)
3-5. TUNER PACK
2
flat wire
3
tuner pack
HCD-GNV99D/GNV111D
1
two screws
(+BVTP 3
4
cover (tuner)
´
6
11
Page 12
HCD-GNV99D/GNV111D
)
3-6. TAPE MECHANISM DECK, MIC BOARD
4
5
tape mechanism deck
screw
(+BVTP2.6 (3CR))
3
cover (TCM)
1
two screws
(+BVTP2.6 (3CR)
2
two screws
(+BVTP2.6 (3CR))
8
knob (MIC)
6
two screws
(+BVTP2.6 (3CR))
7
bracket (MIC)
9
MIC board
12
Page 13
3-7. PANEL BOARD, CD-SW BOARD
qh
escutheon (X-ROUND)
qj
CD-SW board
qg
screw
(+BVTP2.6 (3CR))
qf
two screws
(+BVTP2.6 (3CR))
qs
two screws
(+BVTP2.6 (3CR))
0
knob (JOG-X)
qa
screw
(+BVTP2.6 (3CR))
6
three screws
(+BVTP2.6 (3CR))
HCD-GNV99D/GNV111D
5
two screws
(+BVTP2.6 (3CR))
4
four screws
(+BVTP2.6 (3CR))
8
claw
1
knob vol
2
two knobs (AMS)
7
connector
qd
two screws
(+BVTP2.6 (3CR))
(CN902)
3
three screws
(+BVTP2.6 (3CR))
9
PANEL board
13
Page 14
HCD-GNV99D/GNV111D
)
3-8. DVD MECHANISM DECK
4
DVD mechanism deck
9
connector
(CN800)
8
connector
(CN401)
7
13p(CN520)
flat wire
5
connector
(CN701)
6
flat wire
19p(CN521)
3
three screws
(+BVTP 3
1
three screws
(+BVTP 3
´
10)
2
(+BVTP 3
´
10)
screw
´
10
MAIN board
14
Page 15
)
3-9. VIDEO BOARD, DMB10 BOARD
6
CDM cover
HCD-GNV99D/GNV111D
3
VIDEO board
2
screw
(+BVTP 3´10)
1
13p(CN801)
5
screw
(+BVTP 3´10)
flat wire
0
two screws
(+BVTP 3´10)
8
flat wire
24p(CN101)
4
two screws
(+BVTP 3´10)
qs
bracket (mediatec
qa
DMB10 board
9
two screws
(+BVTP 3´10)
7
connector
(CN201)
15
Page 16
HCD-GNV99D/GNV111D
)
3-10. BACK PANEL
2
connector
(CN1204)
9
connector
(CN580)
8
back panel
1
connector
(CN1200)
7
screw
(+BVTP 3
6
screw
(+BVTP 3
5
two screws
(+BVTP 3
4
screw
(+BVTP 3
3
three screws
(+BVTP 3
´
10)
´
10)
´
10)
´
10
´
10)
3-11. PRIMARY BOARD
4
PRIMARY board
1
connector
3
screw
(+BVTP 3´8)
2
connector
16
Page 17
HCD-GNV99D/GNV111D
s
3-12. POWER AMP PC BOARD ASSY, MAIN BOARD
4
3
screw
(+BVTP 3
1
connector
(CN1213)
2
connector
(CN1212)
two screws
(+BVTP 3
´
6)
´
6)
5
screw
(+BVTP 3
7
6
screw
(+BVTP 3
´
6)
power AMP PC board assy
´
10)
3-13. DVD SURR BOARD, PA BOARD
3
DVD SURR board
0
heat sink
5
two screws
(+BVTP 3
6
´
10)
holder
q;
MAIN board
2
screw
(+BVTP 3
qs
bracket
8
two screws
(+BVTP 3
´
10)
qa
screw
(+BVTP 3
9
(+BVTP 3
´
10)
1
two screw
(transistor)
´
10)
screw
´
10)
qd
PA board
4
connector
(CN602)
9
two screws
(+BVTP 3
7
three screws
(+BVTP 3
´
10)
8
two screws
(transistor)
´
10)
17
Page 18
HCD-GNV99D/GNV111D
3-14. POWER TRANSFORMER (T1200)
3
two screws
1
connector
(CN1213)
2
connector
(CN1212)
4
screw
TRANS board
5
two screws
6
screw
7
power transfomer (T1200)
3-15. DRIVER BOARD, SW BOARD
1
two
screws
(+BTTP (M2.6))
4
DRIVER
2
5p(CN702)
board
flat wire
3
connector (CN703)
5
screw
(+BTTP (M2.6))
6
SW board
18
Page 19
Y
w
3-16. DVD ASSY
1
floating
(+PTPWH M2.6)
screw
HCD-GNV99D/GNV111D
2
DVD
ASS
3-17. OPTICAL PICK-UP
3
insulator screw
8
insulator
4
insulator screw
9
insulator
5
optical pick-up
(KHM-310CAB/C2NP)
2
insulator screw
7
insulator
1
6
insulator scre
insulator
19
Page 20
HCD-GNV99D/GNV111D
3-18. SENSOR BOARD
1
(+PTPWH M2.6)
2
t
ray
6
(+PTPWH M2.6)
7
floating
floating
screw
g
ear (geneva)
screw
8
s
crew
(+BTTP (M2.6))
0
SENSOR board
9
connector
(
CN731)
3
b
elt (table)
4
floating
(+PTPWH M2.6)
5
screw
p
ulley (table)
3-19. MOTOR (TB) BOARD
table
2
stopper
4
8
6
Remove the two solderings of motor.
5
two
screws
(+BTTP (M2.6))
1
stopper
7
t
able motor assy (M741)
3
flat wire 5p (CN742)
MOTOR (TB) board
20
Page 21
3-20. MOTOR (LD) BOARD
2
Remove the two solderings of motor.
5
l
oading motor assy (M751)
3
two
screws
(+BTTP (M2.6))
4
MOTOR (LD) board
HCD-GNV99D/GNV111D
1
b
elt (loading)
21
Page 22
HCD-GNV99D/GNV111D
SECTION 4
TEST MODE
[GC TEST MODE]
• This mode is used to check the fluorescent indicator tube, LEDs,
keys, VOLUME jog, OPERATION DIAL jog, AMS jog, XROUD jog (for GNV111D only) model, destination, software
version and VACS level.
Procedure:
1. Press
2. All LEDs and segments in fluorescent indicator tube are lighted up.
3. When you want to enter the software version display mode,
4. Each time
5. When
x
button, [ENTER] button and [DISC2] button
simultaneously.
All LEDs are lighted up in red color, if the system is turned on,
the POWER LED is lighted up in green color.
[DISC1] button. The model and destination are displayed.
press
[DISC1] button is pressed, the display changes from
MC version, GC version, SYS version, DVD version, ST
version, TC version, TA version, TM version in this order, and
returns to the MC version display.
[DISC3] button is pressed while the version numbers are
being displayed except model and destination, the date of the
software creation appear. When
the display returns to the software version display. When
[DISC3] button is pressed again,
[DISC1] button is pressed while the date of the software creation
is being displayed, the date of the software creation is displayed
in the same order of software version display.
6. Press
7. In the key check mode, the fluorescent indicator tube displays
[DISC2] button, the key check mode is activated.
“K0 J0 V0 E0 X0”.
Each time a button is pressed, “K” value increases. However,
once a button has been pressed, it is no longer taken into account.
“J” value increases in the manner of 0,1, 2, 3 ... if
[OPERATION
DIAL] knob is turned clockwise, or it decreases in the manner
of 0, 9, 8,7 ... if
clockwise.
“V” value increases in the manner of 0, 1, 2, 3 ... if
knob is turned clockwise, or it decreases in the manner of 0, 9,
8,7 ... if
“E” value increases in the manner of 0, 1, 2, 3 ... if
knob is turned clockwise, or it decreases in the manner of 0, 9,
8,7 ... if
“X” value increases in the manner of 0, 1, 2, 3 ... if
[OPERATION DIAL] knob is turned counter-
[VOLUME]
[VOLUME] knob is turned counter-clockwise.
.>
knob is turned counter-clockwise.
[X-ROUND
.>
JOG] knob is turned clockwise or it decreases in the manner of
0, 9, 8, 7 ... if
(For GNV111D only)
8. When
in fluorescent indicator tube light up, the fluorescent indicator
tube displays “VACS A+B APCC”. A is VACS level which is
trigger by signal level, B is VACS level which is trigger by
temperature and CC is VACS level which is trigger by APVACS
(Abuse Protection VACS).
The signal level, which will trigger VACS A is shown in the
center area of the fluorescent indicator tube.
9. When
LEDs and segments in fluorescent indicator tube light up,
alternate segments in fluorescent indicator tube would light up.
If you press
half of alternate segments in fluorescent indicator tube would
light up. Pressing
would cause all segments lights up.
10. To release from this mode, press three buttons in the same
manner as step 1, or disconnect the power cord.
[X-ROUND JOG] knob is turned counterclockwise.
[DISC3] button is pressed after all LEDs and segments
[EX-CHANGE/DISC SKIP] button is pressed after all
[EX-CHANGE/DISC SKIP] button again, another
[EX-CHANGE/DISC SKIP] button again
Procedure:
•To enter MC Test Mode
1. Press
2. The DVD ring indicators and TAPE A and B indicators flash on
Check of Amplifier
*
1. Press [EQ BAND] button repeatedly until a message “GEQ MAX”
2. Press [EQ BAND] button repeatedly until a message “GEQ MIN”
3. Press [EQ BAND] button repeatedly until a message “GEQ FLAT”
4. When the [VOLUME] knob is turned clockwise even slightly,
5. When the [VOLUME] knob is turned counter-clockwise even
Tape function
*
1. When a tape is inserted in Deck B and recording is started, the
2. During recording, turn
To release from MC Test mode
*
1. To release from this mode, press
2. The cold reset is enforced at the same time.
x
button, [ENTER] button and [DISC3] button
simultaneously.
the fluorescent indicator tube. The function is changed to TV.
appears on the fluorescent indicator tube. GEQ increases to its
maximum.
appears on the fluorescent indicator tube. GEQ increases to its
minimum.
appears on the fluorescent indicator tube. GEQ set to flat.
the sound volume increases to its maximum and a message
“VOLUME MAX” appears on the fluorescent indicator tube.
slightly, the sound volume decreases to its minimum and a
message “VOLUME MIN” appears on the fluorescent indicator
tube.
function is changed to TV automatically. When [CD SYNC]
button is pressed during recording in function, ALC (Automatic
Logic Control) is turned on.
m M
stop the recording and the function is changed to TAPE B and
rewind the tape in Deck B until the recording start position and
playback of the tape B is started. If the [REC PAUSE/ START]
button is pressed for a pause and pressed again to resume
recording during recording time, when the tape is rewind, the
tape will be rewind until the position where the pause is applied.
knob counterclockwise will
button.
?/1
[COLD RESET]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions.
Procedure:
1. Press
simultaneously.
2. “COLD RESET” appears in the fluorescent indicator tube. Then,
the fluorescent indicator tube becomes blank for while, and the
set is reset.
x
button, [ENTER] button, and
?/1
button
[VACS ON/OFF]
•This mode is used to switch ON and OFF the VACS (Variable
Attenuation Control System).
Procedure:
1. Press
2. Press
The message “VACS OFF” or “VACS ON” appears on the
fluorescent indicator tube.
button to turn the set ON.
?/1
x
button and [ILLUMINATION] button simultaneously
[MC TEST MODE]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
22
Page 23
HCD-GNV99D/GNV111D
[TUNER STEP CHANGE]
•The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press
button to turn the set ON.
?/1
2. Press [TUNER/BAND] button to select the “AM”.
3. Press
4. Press [ENTER] button and
button to turn the set OFF.
?/1
button simultaneously. The set
?/1
will power ON automatically. The message “AM 9k STEP” or
“AM 10k STEP” appears on the fluorescent indicator tube and
thus the channel step is changed.
[DVD SHIP MODE (WITH MEMORY CLEAR)]
• This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the
RAM to initial conditions. Use this mode when returning the
set to the customer after repair.
Procedure:
1. Press
2. Select DVD function.
3. Press
simultaneously. The set will power off automatically.
4. After the “STANDBY” blinking display finish, a message
“MECHALOCK” is displayed on the fluorescent indicator tube
and the DVD ship mode is set.
button to turn the set ON.
?/1
x
button, [DVD] button and
?/1
button
[DVD COLOR SYSTEM SWITCHING]
• This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press
button to turn the set ON.
?/1
2. Select DVD function.
3. Press
4. Press [PAUSE] button and
button to turn the set OFF.
?/1
button simultaneously. The set
?/1
will power on automatically.
5. The message “COLOR PAL” or “COLOR NTSC” will be
displayed on the fluorescent indicator tube.
[REMOTE COMMANDER DISABLE MODE]
•This mode let you disable the remote commander reception. When
this mode is activated, the set will not response if the button on
the remote commander is pressed. The message “RemoteDisable”
will be displayed on the fluorescent indicator tube. Use this mode
during aging to avoid disturbance.
Procedure:
x
1. Press
simultaneously, “RemoteDisable” displayed on the fluorescent
indicator tube. To enable the remote commander reception, press
the same buttons again.
“RemoteEnable” displayed on the fluorescent indicator tube.
button, [GROOVE] button and [DISC 2] button
[DVD SHIP MODE (WITHOUT MEMORY CLEAR)]
• This mode moves the optical pick-up to the position durable to
vibration.
Procedure:
1. Press
button to turn the set ON.
?/1
2. Select DVD function.
3. Press [DVD] button and
button simultaneously. The set
?/1
will power off automatically.
4. After the “STANDBY” blinking display finish, a message
“MECHALOCK” is displayed on the fluorescent indicator tube
and the DVD ship mode is set.
[DVD TRAY LOCK MODE]
•This mode let you lock the disc tray. When this mode is
activated, the disc tray will not open when [OPEN/CLOSE]
button or [EX-CHANGE/DISC SKIP] button is pressed. The
message “LOCKED” will be displayed in on the fluorescent
indicator tube.
Procedure:
1. Press
2. Select DVD function.
3. Press
and hold down until “LOCKED” or “UNLOCKED” displayed
on the fluorescent indicator tube (around 5 seconds).
button to turn the set ON.
?/1
x
button and [OPEN/CLOSE] button simultaneously
[VIDEO/SAT SWITCHING]
•This mode let you switch from VIDEO to SAT and vice-versa.
Procedure:
1. Press
2. Select TV/SAT function.
3. Press [TV/SAT] button and
function will change to SAT. Press the same buttons again to
change from SAT to VIDEO.
button to turn the set ON.
?/1
button simultaneously. The
?/1
23
Page 24
HCD-GNV99D/GNV111D
[DVD SERVICE MODE]
• This mode let you make diagnosis and adjustment easily by using the remote commander and TV. The instructions, diagnostic
results, etc. are given on the on-screen display (OSD).
Procedure:
1. Press
2. Select DVD function.
3. Press
and then turn the [VOLUME] knob clockwise.
4. The message “SERVICE IN” will be displayed on the
fluorescent indicator tube and the Test Mode Menu is displayed
on the on-screen display on the TV. The model name and revision
number is displayed at the bottom of the on-screen display.
button to turn the set ON.
?/1
x
button and [OPEN/CLOSE] button simultaneously
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History Check
4. Version information
5. Video Level Adjustment
Model: GNV99D_E
IF-con Ver : 00.10(0000)
Syscon Ver : 0.165
[EXECUTING IOP MEASUREMENT]
In order to execute mirror time adjustment, the following standard
procedures must be followed.
1. In standby mode, press x button and [OPEN/CLOSE] button
simultaneously and the turn the [VOLUME] knob clockwise.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History Check
4. Version information
5. Video Level Adjustment
Model: GNV99D_E
IF-con Ver : 00.10(0000)
Syscon Ver : 0.165
2. Select “2. Drive Manual Operation” by pressing the [2] button
on the remote commander. The screen will appear as below.
Drive Manual Operation
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press
OFF.
button to turn the set
?/1
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time adjust
0. Return to top Menu
3. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The screen will appear as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
? ? Change Value
[RETURN] Return to previous menu
24
4. Select Iop by pressing [6] button on the remote commander.
Page 25
HCD-GNV99D/GNV111D
5. Wait until a hexadecimal number appear.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
Change Value
[0] Return to previous menu
6. Convert data from hexadecimal to decimal using conversion
table.
7. Press [RETURN] to return back to previous menu.
8. Press [0] to return to Top Menu and power OFF the DVD Player.
6. Error code list
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mecha move error (5 Changer)
26: Mecha move stack error
30: DC Motor adjustment error
31: DPD offset adjustment error
32: TE Balance adjustment error
33. TE Sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus Layer Jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: read Qdata/ID error
70: Lead In Data Read Fail
71: TOC read time out (CD)
80: Can’t Buffering
81: Unknown media type
[EMERGENCY HISTORY CHECK]
Information of Emergency History.
1. In standby mode, press [TOP MENU], [CLEAR],
enter Remocon Diagnosis Mode.
2. Select “3. Emergency History”.
Emg. History Check
Laser HoursCD999h59min
DVD999h59min
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
2. 02 02 01 0100 A9 4B 00
00 00 00 0000 00 23 45
[Next] Next Page [Prev] Prev Page
3. Laser Hours
DVD Laser ON time. (Total ON time)
CD Laser ON time. (Total ON time)
4. Emergency History
The history information from last “1” to “10” can be
scrolled with [NEXT] button or [PREV] button.
5. Error code
Example of Error code
?/1
buttons to
7. Error code parameters
Example of Error code
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
This is the detailed contents od error information
8. Laser hours at error happend.
Example of Error code
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
This is Laser hours when an error happaned.
9. How to Clearing laser hours
Press [DISPLAY], [CLEAR] buttons in this order.
Both CD and DVD data are cleared.
Emg. History Check
Laser HoursCD0h0min
DVD0h0min
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
2. 02 02 01 0100 A9 4B 00
00 00 00 0000 00 23 45
[Next] Next Page [Prev] Prev Page
[0] Return to Top Menuas
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
25
Page 26
HCD-GNV99D/GNV111D
10. How to Clearing Emergency code
Press [TOPMENU], [CLEAR] buttons in this order.
All emergency code are cleared.
Emg. History Check
Laser HoursCD999h59min
DVD999h59min
1. 00 00 00 0000 00 00 00
00 00 00 0000 00 00 00
2. 00 00 00 0000 00 00 00
00 00 00 0000 00 00 00
[Next] Next Page [Prev] Prev Page
11. Press [0] button, return to TOP MENU.
[INITIALIZING SETUP DATA]
How to initializing setup data.
1. In standby mode, press [TOP MENU], [CLEAR],
to enter Remocon Diagnosis Mode.
2. Select “3. Emergency History”.
Emg. History Check
Laser HoursCD999h59min
DVD999h59min
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
2. 02 02 01 0100 A9 4B 00
00 00 00 0000 00 23 45
[Next] Next Page [Prev] Prev Page
3. Initializing setup data
Press [MENU], [CLEAR] buttons in this order.
The data have been initialized when “Initialize setup data...”
mesage is displayed.
?/1
buttons
4. The Emergency history display screen will be restored soon.
Emg. History Check
Laser HoursCD999h59min
DVD999h59min
1. 01 05 04 0400 92 46 00
00 00 00 0000 00 23 45
2. 02 02 01 0100 A9 4B 00
00 00 00 0000 00 23 45
[Next] Next Page [Prev] Prev Page
5. Press [0] button, return to TOP MENU.
[VERSION INFORMATION]
Information of firmware version.
1. In standby mode, press [TOP MENU], [CLEAR], [POWER]
buttons to enter Remocon Diagnosis Mode.
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads pinch rollers
erase headrubber belts
capstanidlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to
the parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
ModeTorque meterMeter reading
3.06 N • m to 6.96 N • m
FWDCQ-102C31 to 71 g • cm
(0.43 – 0.98 oz • inch)
FWD
back tension
REVCQ-102RC31 to 71 g • cm
REV
back tension
FF/REWCQ-201B71 to 143 g • cm
FWD tensionCQ-403A100 g or more
REV tensionCQ-403R100 g or more
CQ-102C2 to 6 g • cm
CQ-102RC2 to 6 g • cm
0.19 N • m to 0.58 N • m
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m
(0.98 – 1.99 oz • inch)
9.80 N • m
(3.53 oz or more)
9.80 N • m
(3.53 oz or more)
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and RCH.
7. Switches and controls should be set as follows unless otherwise
specified.
•Test Tape
TapeSignalUsed for
P-4-A10010 kHz, –10 dBAzimuth Adjustment
RECORD/PLAYBACK HEAD AZIMUTH ADJUST-MENT
DECK A DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback
0 dB=0.775 V
27
Page 28
HCD-GNV99D/GNV111D
e
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
Output
level
within
1dB
L-CH
peak
R-CH
peak
within
1dB
Screw
position
L-CH
peak
Screw
position
R-CH
peak
3. Mode: Playback
test tape
P-4-A100
(10 kHz, –10 dB)
L-CH
MAIN
board
CN510
set
R-CH
waveform of oscilloscope
in phase 45°90°135°180
pin
L
R
pin
good
1
pin
3
2
oscilloscop
V
wrong
H
°
4. After the adjustments, apply suitable locking compound to
the pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
DVD SECTION
AUTO SERVO ADJUSTMENT
After parts related to the servo circuit (RF amplifier , DSP (IC102),
motor driver (IC201), EEPROM (IC103) so on) are replaced, readjusting the servo circuit is necessary.
[TEST DISC LIST]
Use the following test disc on test mode.
TDV-520CSO (DVD-SL):PART No. J-2501-236-A
LUV-P01 (CD):PART No. 4-999-032-01
TDV-540C (DVD-DL):PART No. J-2501-235-A
Note: Do not use exiting test disc for DVD.
[RFMON Level Check]
Connection:
oscilloscope
DMB10 board
CN105 pin 6 (RFMON)
CN105 pin
3
(GND)
Procedure:
1. Connect an oscilloscope to CN105 pin 6 (RFMON) and
CN105 pin 3 (GND) on the DMB10 board.
2. Turn the power on.
3. Set the test disc (DVD: TDV-520CSO, CD: LUV-P01) on the
tray and press H button to playback.
4. Confirm that oscilloscope waveform is clear and check
RFMON signal level is correct or not.
Note: A clear RFMON signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
RFMON signal waveform
0.8 ± 0.2 Vp-p (CD)
+
–
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level: 0.8 ± 0.2 Vp-p (DVD)
28
forwardreverse
Checking Location: DMB10 board (Side A)
IC104
IC102
CN105
IC201
6
1
CN105 pin 3 (GND)
IC101
CN106
CN105 pin 6 (RFMON)
Page 29
SECTION 7
R
MAIN board
MIC board
JOG board
PANEL board
MOTOR (LD) board
SW board
SENSOR board
DRIVER board
MOTOR (TB) board
DIAGRAMS
HCD-GNV99D/GNV111D
For Schematic Diagrams.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
• All resistors are in Ω and 1/
•%: indicates tolerance.
•f: internal component.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
• A : B+ Line.
• B : B– Line.
•Voltages and waveforms are dc with respect to ground un-
•Voltages are taken with a VOM (Input impedance 10 MΩ).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
50 V or less are not indicated except for electrolytics and
tantalums.
specified.
Note:
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
der no-signal (detuned) conditions.
DMB10 and VIDEO boards
no mark : DVD PLAY
Other board
no mark : TUNER (FM/AM)
( ): DVD PLAY
<>: TAPE PLAY
[]: TAPE REC
*: Impossible to measure
Voltage variations may be noted due to normal production
tolerances.
Voltage variations may be noted due to normal production
tolerances.
F: AUDIO
e: TUNER
k: TAPE PLAY (DECK A)
d: TAPE PLAY (DECK B)
G: REC (DECK B)
J: CD PLAY
N: MIC
c: DVD PLAY
L: VIDEO
E: Y
a: CHROMA
r: COMPONENT VIDEO
q: R, G, B
4
W or less unless otherwise
Note on Printed Wiring Boards.
Note:
• X : parts extracted from the component side.
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(SIDE A) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(SIDE B) the parts face are indicated.
• Indication of transistor.
C
Q
B
E
Q
B
CE
Q
B
CE
•Abbreviation
AUS: Australian model
E2 : 120V AC Area in E model
E3 : 240V AC Area in E model
E15 : Iran model
EA : Saudi Arabia model
MY : Malaysia model
PH : Philippines model
SP : Singapore model
New part of EEPROM (IC103) on the DMB10 board can not be used. Therefore, if the mounted
DMB10 board (A-1099-272-A or A-1099-344-A or A-1115-347-A) is replaced, exchange new
EEPROM with that used before the replacement.
Page 37
HCD-GNV99D/GNV111D
7-8. PRINTED WIRING BOARD – DMB10 Section (SIDE B) –
34567
C3708
R3779
R3729
IC3771
C3706
R3759
R3749
IC3751
IC301
FL104
R1134
FL108
C213
R213
R205
R206
C209
R221
R226
R220
C214
C212
R223
R225
R1110
R232
R230
R231
C3607
C3602
R3601
)
C3610
C3621
20
C3601
L3601
2
R3621
R3611
1
C3611
D3601
R3739
R3719
IC3711
D3602
C3702
C3704
1
A
B
DMB10 BOARD(SIDE B
10
R3602
IC3601
R3609
11
IC3731
C
C301
R314
R3606
R3605
D
E
F
G
H
R204
R3652
R207
R212
C233
C211
R2504
C203
• See page 29 for Circuit Boards Location. :Uses unleaded solder.
New part of EEPROM (IC103) on the DMB10 board can not be used. Therefore, if the mounted
DMB10 board (A-1099-272-A or A-1099-344-A or A-1115-347-A) is replaced, exchange new
EEPROM with that used before the replacement.
4040
Page 41
7-12. SCHEMATIC DIAGRAM – DMB10 Section (4/4) –
DMB10
BOARD
8
(2/4)
(Page 39)
HCD-GNV99D/GNV111D
DMB10
BOARD
(2/4)
(Page 39)
14
DMB10
BOARD
(2/4)
(Page 39)
R223
100k
R221
C209
C233
0.033
0.0047
R220
R212
10k
10k
1.4
R206
10k
R208
33k
C205
220p
R214
1.4
15k
1.4
1.4
1.4
R209
33k
C206
220p
R215
12k
3.3
C203
R207
0.01
2.7k
R204
1.2k
9
R205
10k
3.3
2.2
1.4
1.4
R210
47k
C208
0.01
R216
12k
1.4
1.4
R213
6.8k
R225
100k
C211
56k
0.033
56k
R226
2.1
2.1
0.3
4.9
R230
82k
C212
0.01
C214
0.001
1.4
R231
15k
R232
18k
R234
10k
C215
R233
0.01
33k
2.9
2.9
1.7
9
9
4.3
4.3
CN201
DMB10
BOARD
(2/4)
1
(Page 39)
6P
4.3
4.3
JL205
4.8
C218
16V
C219
0.01
C224
0.01
C220
10
10
16V
C221
0.1
R246
4.7k
R247
1k
11
DMB10
BOARD
(2/4)
(Page 39)
3.5
4.4
4.2
3.3
C222
0.1
IC201
FAN8036L
5.3
DMB10 BOARD (2/4)
(Page 39)
DMB10 BOARD (2/4)
(Page 39)
DMB10 BOARD (2/4)
(Page 39)
HCD-GNV99D/GNV111D
MAIN
BOARD
(5/5)
(Page 49)
12
R219
27k
R224
10k
C210
0.01
0
1.4
1.1
R2504
C213
4.7k
0.01
3.3
3
3.3
9
3.3
C217
47
16V
6
5
CN401
5P
D
FB401
0UH
FB402
0UH
FL401
0UH
FL402
EMI
C402
16V
FB404
0UH
FB403
0UH
47
FB405
0UH
FL403
0UH
C403
6.3V
47
FB406
0UH
DMB10
BOARD
13
(Page 38) (Page 39) (Page 40)
DMB10
BOARD
15
(Page 38) (Page 39) (Page 40)
(2/4)(1/4)(3/4)
(2/4)(1/4)(3/4)
4141
Page 42
HCD-GNV99D/GNV111D
7-13. PRINTED WIRING BOARDS – CD MECHANISM Section –
1
234567891011121314
A
MOTOR(LD) BOARD
B
C
D
CN721
E
• See page 29 for Circuit Boards Location. :Uses unleaded solder.
7-31. PRINTED WIRING BOARDS – TRANS AND PRIMARY Section –
1
2
TRANS BOARD
A
B
EXCEPT AUS
4
C
1
AUS
D
NO1211
34567
T1200
POWER TRANSFORMER
JW1208
JW1209
JW1220
JW1221
• See page 29 for Circuit Boards Location. :Uses unleaded solder.
8
F1241
JW1206
JW1207
*
*
JW1202
JW1201
NOT REPLACEABLE:
BUILT IN TRANSFORMER
FH1292
F1291
D1292
FH1242
FH1252
FH1291
JW1216
R1292
FH1262
FH1272
C1292
FH1282
F1251
R1263
F1261
F1271
E
R1262
Q1264
F1281
FH1241
FH1251
FH1261
R1264
C1262
D1264
FH1271
C1263
JW1211
910
CN1212
7
JW1222
1
JW1223
CN1213
8
FH1281
1
JW1210
1-864-931-
11
(11)
S
PA
BOARD
(Page 54)
N
MAIN
BOARD
(Page 44)
• Semiconductor
Location
Ref. No.
D1200F-3
D1264D-8
D1292C-7
Q1200F-2
Q1264D-8
Location
E
PRIMARY BOARD
JR1202
2
1
CN1202
NO1201
1
2
2
C1204
EP1203
AC IN
AUS
EXCEPT AUS
JW1204
S1200
VOLTAGE
JW1213
1-864-932-
SELECTOR
230 - 240V
r
220V
r
120V
11
(11)
POWER
SWITCHING
C1201
F
MAIN
BOARD
(Page 44)
CN1200
L
C1206
L1201
Q1200
R1201
E
3
R1200
1
C1202
D1200
RY1200
G
1
NO1203
EXCEPT AUS
AUS
4
H
1
JW1214
JW1215
CN1204
I
HCD-GNV99D/GNV111D
6060
Page 61
7-32. SCHEMATIC DIAGRAM – TRANS AND PRIMARY Section –
F1241
T8.00AL
250V
F1251
T8.00AL
250V
CN1212
S
PA
BOARD
(Page 55)
7P
F1261
T8.00AL
250V
F1271
T8.00AL
250V
T1200
POWER
TRANSFORMER
NO1211
*
CN1204
2P
4P
CN1204
AUS
EXCEPT AUS
*
HCD-GNV99D/GNV111D
EXCEPT AUS
S1200
VOLTAGE SELECTOR
N
MAIN
BOARD
(5/5)
(Page 49)
CN1213
8P
8
1
JW1211
F1281
T3.15AL
250V
F1291
T3.15AL
250V
C1262
10
50V
HZU36BTRF
C1263
100
50V
D1264
R1262
8.2k
R1263
8.2k
R1264
1k
C1292
100
63V
R1292
Q1264
2SB1565E
–35V REG
0.68
JW1292
JW1293
D1292
10EDB40
*
*
NOT REPLACEABLE:
BUILT IN TRANSFORMER
AUS
EXCEPT AUS
R1200
4.7k
R1201
100k
CN1200
3P
120V
220V
230-240V
AUS
JW1204
Q1200
2SC1623-L5L6
RELAY DRIVE
C1201
0.1
C1206
1000
6.3V
RY1200
D1200
1SS355TE-17
L1201
18uH
JR1202
0
C1202
0.1
EP1203
C1204
0.1
NO1201
2P
NO1203
2P
CN1202
2P
AC IN
HCD-GNV99D/GNV111D
L
MAIN
BOARD
(1/5)
(Page 45)
6161
Page 62
HCD-GNV99D/GNV111D
1.0 Vp-p
H
0.5 V/DIV, 20 msec/DIV
1.3 Vp-p
H
0.5 V/DIV, 20 msec/DIV
1.6 Vp-p
H
0.5 V/DIV, 20 msec/DIV
1.6 Vp-p
H
0.5 V/DIV, 20 msec/DIV
0.8 Vp-p
H
0.5 V/DIV, 20 msec/DIV
2.0 Vp-p
H
1 V/DIV, 20 msec/DIV
2.6 Vp-p
H
1 V/DIV, 20 msec/DIV
1 V/DIV, 20 msec/DIV
0.8 Vp-p
H
0.5 V/DIV, 20 msec/DIV
1.5 Vp-p
H
1 V/DIV, 20 msec/DIV
1 V/DIV, 20 msec/DIV
2.0 Vp-p
H
1 V/DIV, 20 msec/DIV
1 V/DIV, 20 msec/DIV
2.0 Vp-p
H
1.5 Vp-p
H
2.6 Vp-p
H
1
IC801 2
CIN
2
IC801 4
CVBSIN
3
IC801 6
YIN
qa
IC801 wd
CVBSOUT
qs
IC801 wh
C OUT
qd
IC800 7
VOUT
4
IC801 0
CTIN
5
IC801 qs
CBIN
6
IC801 qf
CRIN
7
IC801 qh
CROUT
8
IC801 qk
CBOUT
9
IC801 w;
CYOUT
0
IC801 wa
YOUT
•Waveforms
– DMB10 Board –
1
IC301 9
2V/DIV, 0.1 msec/DIV
2
IC301 0
41 nsec
2V/DIV, 20 nsec/DIV
3
IC102 6
BICK
0.33
m
sec
MCLK
DVDRFIP
3.3 Vp-p
4.0 Vp-p
4
IC102 ea
0.1V/DIV, 0.5 msec/DIV
5
IC102 es
0.1 V/DIV, 0.5 msec/DIV
6
IC102
FED
TEO
228
XTALO
0.1 Vp-p
0.1 Vp-p
– VIDEO Board –
0.2V/DIV, 50 nsec/DIV
– MAIN Board –
1
0.5 V/DIV, 10 msec/DIV
2
IC401 qa
IC401 qd
32 msec
XC OUT
X-OUT
0.6 Vp-p
1.7 Vp-p
3.3 Vp-p
0.5V/DIV, 20 nsec/DIV
40 nsec
1.1 Vp-p
200 nsec
1V/DIV, 50 nsec/DIV
3
CN503 8
20V/DIV, 5 msec/DIV
HCD-GNV99D/GNV111D
E-HOT
11 msec
60 Vp-p
6262
Page 63
• IC Block Diagrams
IC701, 712 BA6956AN (DRIVER BOARD)
TSD
CONTROL LOGIC
123456789
VREF
OUT2
RNF
OUT1
VM
VCC
FIN
GND
HCD-GN99D/GNV111D
RIN
IC800 NJM2244M-TE2 (VIDEO BOARD)
1
VIN1
2
SW1
VIN2
SW2
3
4
BIAS
75 Ω
DRIVER
8 GND
7 VOUT
6 VCC
5 VIN3
63
Page 64
HCD-GNV99D/GNV111D
BUF1OUT
BPF2IN1
BPF2IN2
BPF3IN1
BPF3IN2
BPF4IN1
BPF4IN2
IC904 NJM2760V-TE2 (PANEL BOARD)
IN1
1
IN2
GND
2
3
4
5
6
7
8
9
10
DET
BPFDET
BPFDET
BPFDET
BPF
DET
20
19
18
17
16
15
14
13
12
11
BPF2OUT
BPF1IN1
BPF1IN2
RECOUT
BPF1OUT
BPF2OUT
BPF3OUT
BPF4OUT
NC
VCC
LIN 1
RIN
V_ERF_1
V_ERF_2
VCC
AGND
PDWN 7
BTPASS
FSYNC
LRCK
IC3601 PCM1803DBR (DMB10 BOARD)
Single-End
2
3
4
5
6
8
9
10
/Differential
Converter
Reference
Single-End
/Differential
Converter
Power Supply
5 th Order
Delta-Sigma
Modulator
5 th Order
Delta-Sigma
Modulator
× 1/64 (× 1/128)
Decimation
Filter
with
DC Cut Filter
Clock and Timing Control
Serial
Interface
Mode/
Format
Control
MODE120
MODE0
19
FMT1
18
FMT0
17
OSR16
SCKI15
14
VDD
DGCD
13
DOUT
12
BCK
11
64
Page 65
HCD-GN99D/GNV111D
• IC Pin Function Description
IC102 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGGITAL SERVO
PROCESSOR) (DMB10 BOARD)
Pin No.Pin NameI/ODescription
1AGND–Ground
2DVDAIAC coupled RF signal input A
3DVDBIAC coupled RF signal input B
4DVDCIAC coupled RF signal input C
5DVDDIAC coupled Rf signal input D
6DVDRFIPIAC coupled DVD RF signal input
7DVDRFINIAC coupled DVD RF signal input (Not used)
8NAIRF signal input A
9NBIRF signal input B
10MCIRF signal input C
11MDIRF signal input D
12SAISub-beam RF signal input A (Not used)
13SBISub-beam RF signal input B (Not used)
14SCISub-beam RF signal input C (Not used)
15SDISub-beam RF signal input D (Not used)
16CDFONICD focusing error negative input (Not used)
17CDFOPICD focusing error positive input (Not used)
18TNIIRF signal input E
19TPIIRF signal input F
20MDI1ILaser power PD monitor input
21MDI2ILaser power PD monitor input
22LDO2OLaser drive signal output
23LDO1OLaser drive signal output
24SVDD3–Power Supply (+3.3V)
25CSDONot used (Open)
26RFLVLOPositive main beam summing output
27SGNDOGround
28V2REFOOReference voltage output
29V2OOCenter voltage output
30VREFOOReference voltage output
31FEOOFocus error signal output
32TEOOTracking error signal output
33TEZISLYOTE Slicing Level (Not used)
34OPOUT–Not used (Open)
35OPIN–Not used (Open)
36OPIN–Not used (Open)
37DMOOSpindle motor control PWM signal output
38FMOOSled motor PWM signal output
39TROPENPWMOTray PWM output/Tray open output (Not used)
40IOPMONOGeneral PWM signal output
41TROOTracking servo signal output
42FOOOFocus servo signal output
43USBVSS–Ground
44USBP–Not used (Open)
45USBM–Not used (Open)
46USBVDD3–Power Supply (+3.3V)
47SPFGISpindle FG signal input
65
Page 66
HCD-GNV99D/GNV111D
Pin No.Pin NameI/ODescription
48AN0–Not used (Pull up)
49AN1–Not used (Pull up)
50AN2–Not used (Pull up)
51MAMUTEOMAMUTE signal output (Not used)
52DVDD18–Power Supply (+1.8V)
53 to 58IOA 2 to 7OAddress bus 2 to 7 output to FLASH PROM
59HIGHA0OAddress bus 8 output to FLASH PROM
60, 61IOA18, 19OAddress bus 18, 19 output to FLASH PROM
62DVSS–Ground
63APLLCAPIAPLL External Capacitance connection
64APLLVSS–Ground
65VDD3–Power Supply (+3.3V)
66I OWROWrite signal output to FLASH PROM
67A16OAddress bus 16 output to FLASH PROM
68 to 72HIGHA 7 to 3OAddress bus 15 to 11 output to FLASH PROM
73DVDD3–Power Supply (+3.3V)
74, 75HIGHA 2, 1OAddress bus 10, 9 output to FLASH PROM
76IOA20OAddress bus 20 output to FLASH PROM
77IOCSOChip select signal output to FLASH PROM
78IOA1OAddress bus 1 output to FLASH PROM
79IOOEOOut enable signal output to FLASH PROM
80DVDD3–Power Supply (+3.3V)
81 to 84AD 0 to 3I/OData bus 0 to 3 input/output to FLASH PROM
85DVSS–Ground
86 to 88AD 4 to 6I/OData bus 4 to 6 input/output to FLASH PROM
89IOA21OAddress bus 21 output to FLASH PROM
90ALEONot used (Open)
91AD7I/OData bus 7 input/output to FLASH RAM
92A17OAddress bus 17 output to FLASH PROM
93IOA0I/OAddress bus 0 input/output to FLASH RAM
94DVSS–Ground
95UWA–Not used (Open)
96URB–Not used (Open)
97DVDD18–Power Supply (+1.8V)
98IFSDOOSerial data output to M30620MCP
99IFCKOSerial clock data output to M30620MCP
100XIFCSOXIFCS signal output to M30620MCP
101IFSDIISerial data input from M30620MCP
102SCLOSCL signal output to EEPROM
103SDAOSDA signal output to EEPROM
104TRG-SWONot used
105IF-BSYIIFBSY signal input from M30620MCP
106RXDIRD232 RXD signal input
107TXDORD232 TXD signal output
108DVDD3–Power Supply (+3.3V)
109IEC–Not used (Open)
110PRSTISystem reset signal input from M30620MCP
111IR–Not used (Open)
112INT0–Not used (Open)
113DQMOODQM0 signal output to SDRAM
66
Page 67
Pin No.Pin NameI/ODescription
114MREQIDQM signal input
115RD7I/OData bus 7 input/output to SDRAM
116DVSS–Ground
117, 118RD 6, 5I/OData bus 6, 5 input/output to SDRAM
119DVSS–Ground
120, 121RD 4, 3I/OData bus 4, 3 input/output to SDRAM
122DVDD18–Power Supply (+1.8V)
123 to 125RD 2 to 0I/OData bus 2 to 0 input/output to SDRAM
126RD15I/OData bus 15 innput/output SDRAM
127DVDD3–Power Supply (+3.3V)
128RD 14I/OData bus 14 input/output to SDRAM
129 to 133RD 13 to 9I/OData bus 13 to 9 input/output to SDRAM
134DVSS–Terminal Ground
135RD8I/OData bus 8 input/output to SDRAM
136GPI0–Not used (Open)
137DQM1ODQM1 signal output to SDRAM
138REWOWrite signal output to SDRAM
139CASOCAS signal output to SDRAM
140RASORAS signal output to SDRAM
141DVDD3–Power Supply (+3.3V)
142RCSOChip select signal output to SDRAM
143BAOOBAO signal output to SDRAM
144DVSS–Ground
145BA1OBA1 signal output to SDRAM
146RA10OAddress bus 10 output to SDRAM
147RA0OAddress bus 0 output to SDRAM
148DVSS–Ground
149 to 151RA 1 to 3OAddress bus 1 to 3 output to SDRAM
152DVDD18–Power Supply (+1.8V)
153RVREF–Not used (Open)
154RCLKB–Not used (Open)
155DVDD3–Power Supply (+3.3V)
156RCLKOClock output to SDRAM
157CLEOClock enable output to SDRAM
158 to 160RA 11, 9, 8OAddress bus 11, 9, 8 output to SDRAM
161DVSS–Ground
162RA7OAddress bus 7 output to SDRAM
163DVSS–Ground
164 to 166RA 6 to 4OAddress bus 6 to 4 output to SDRAM
167DVDD3–Power Supply (+3.3V)
168DISC/X–Not used (Open)
169RGB–Not used (Open)
170XSMRST–Not used (Open)
171WODEOWide signal output to MM1623BFBE
172NT–Not used
173DVDD18–Power Supply (+1.8V)
174EUR–Not used (Open)
175DVSS–Ground
176LIMSWIOptical pick-up limit switch signal input
177OCSW–Not used
HCD-GN99D/GNV111D
67
Page 68
HCD-GNV99D/GNV111D
Pin No.Pin NameI/ODescription
178VCLK–Not used
179CKSW–Not used
180IO3–Not used
181TSDMOTSDM signal output to FAN8036L
182DVDD3–Power Supply (+3.3V)
183MUTEOMUTE signal output to FAN8036L
184MUTE123OMUTE signal output to FAM8036L
185REV–Not used
186FWD–Not used
187MSWOOptical pick-up volume control signal output
188DSELONot used
189DAVCC–Power Supply (+3.3V)
190VREF–Not used
191FSIFull scale adjustment (pull down)
192YUV0–Not used
193DAVSS–Ground
194YUV1OY signal output to MM1623BFBE
195DAVDD–Power Supply (+3.3V)
196YUV2OCHROMA signal output to MM1623BFBE
197DAVSS–Ground
198YUV3OVIDEO signal output to MM1623BFBE
199DAVDD–Power Supply (+3.3V)
200YUV4OG signal output to MM1623BFBE
201DAVSS–Ground
202YUV5OB signal output to MM1623BFBE
203YUV6OR signal output to MM1623BFBE
204DVDD3–Power Supply (+3.3V)
205MIC/VSYNCIMic status signal input to M30620MCP
206VOICE/YUV7INot used
207KRMOD/HSYNCOKRMOD signal output to M30620MCP
208SMSCK–Not used
209SPDATA/SMSDIIAudio data of SPDIF input
210SMSDO–Not used
211XSMCS–Not used
212DVDD3–Power Supply (+3.3V)
213ALRCKIAudio left/right channel clock input
214ABCKOAudio bit clock output
215ACLKIAudio DAC master clock input
216DVSS–Ground
217ASDATA0OAuido serial data output to AK4358VQ
218ASDATA1OAuido serial data output to AK4358VQ
219ASDATA2OAuido serial data output to AK4358VQ
220XRSTIReset signal input
221DVDD18–Power Supply (+1.8V)
222ASDATA4OAuido serial data output to AK4358VQ
223DVSS–Ground
224DWIDE–Not used (Open)
225SDPIFISerial data input from PCM1803DBR
226RFGND18–Ground
227RFVDD18–Power Supply (+1.8V)
68
Page 69
Pin No.Pin NameI/ODescription
228ZTALOOOscillator output terminal
229ZTALIIOscillator input terminal
230JITFOORF jitter meter output
231JITFNIRF jigger meter input
232PLLVSS–Ground
233IDAC–Not used
234PLLVDD3–Power Supply (+3.3V)
235LPFONONegative output of loop filter amplifier
236LPFIPIPositive input of loop filter amplifier
237LPFININegative input of loop filter amplifier
238LPFOPOPositive output of loop filter amplifier
239VDD3–Power Supply (+3.3V)
240VCMISACD-Common mode Reference
241VSS–Ground
242VREEPISACD-TOP Reference
243VREENISACD-Bottom Reference
244RFVDD3–Power Supply (+3.3V)
245RFRPDCIRFRP signal input
246RFRPACIRFRP signal input
247HRFZCIHigh frequency RF ripple zero crossing
248CRTPLPODefect level filter capacitor connecting
249RFGND–Ground
250CEQPOEQ offset loop capacitance
251CEQNIEQ offset loop capacitance
252OSPORF offset cancellation capacitor connecting
253OSNIRF offset cancellation capacitor connecting
254RFGCORF offset loop capacitor connecting
255IREFICurrent reference input
256AVDD3–Power Supply (+3.3V)
1TUNEDITuner tuning detection signal input
2MC-DOUT(ST)OTuner tuning PLL serial data output
3ST-CLKOTuner tuning PLL serial data transfer clock signal output
4SIRCSIRemote control signal input
5MC-DIN(ST)ITuner tuning PLL serial data input
6ST-CEOTuner tuning PLL chip enable signal output
7STBY-RELAYOMain power on/off control signal output
8BYTE–Not used (connected ground)
9CNVss–Ground
10XC-INISub system clock input terminal (32.768kHz)
11XC-OUTOSub system clock output terminal (32.768kHz)
12RESETISystem reset signal input
13X-OUTOMain system clock output terminal (16MHz)
14VSS–Ground
15X-INIMain system clock input terminal (16MHz)
16VCC–Power supply (+3.3V)
17NMIINon-maskable interrupt input (Not used)
18KRMODIKRMOD signal input from CXD9804R
19VOICEINot used (Open)
20AC-CUTIAC off detection signal input from ICBD4828G
21MIC SWOMic status output to CXD9804R
22MREQIMuting request signal input from CXD9804R
23IFBSYOIFBSY signal to CXD9804R
24XIFCSIXIFCS signal from CXD9804R
25SYSRSTOSystem reset signal output to CXD9804R
26OPEN SWIEject detection signal input
27TBL SENSIDisc tray position detection signal input
28E3IDisc tray status detection signal input
29IIC-CLKI/OIIC serial clock signal input/output
30IIC-DATAI/OIIC serial data signal input/output
31SIOOSerial data output to CXD9804R
32SOOISerial data input from CXD9804R
33SCOISerial clock input from DVD Motherboard
34E2IDisc tray status detection signal input
35E1IDisc tray status detection signal input
36TB-FODisc tray turning motor control signal output
37TM-RODisc tray turning motor control signal output
38LM-FODisc tray loading motor control signal output
39LM-RODisc tray loading motor control signal output
40GC-RESETOReset signal output to MB90M407PF
41STBY LEDOLED drive signal output
42FAN CTRLOFan driving signal output
43NO USEINot used (connected ground)
44NO USEINot used (connected ground)
45NO USEINot used (connected ground)
46A PLAYIDeck A playback detection signal input
47A-HALFIDeck A cassette detection signal input
48A-TRIGODeck A side trigger plunger drive signal output
49B-TRIGODeck B side trigger plunger drive signal output
70
Page 71
HCD-GN99D/GNV111D
Pin No.Pin NameI/ODescription
50CAPMOCapstan motor drive signal output
51B-PLAYIDeck B playback detection signal input
52REC BIASORecording bias on/off control signal output
53TC RELAYORecording/playback selection signal output
54REC MUTEORecording muting on/off control signal output
55PB A/BODeck A/B playback selection signal output
56ALCOAutomatic limiter control signal output
57AMS INIAMS signal input
58FAN KICKOFan kick off pulse output
59CTR SPK SWOCenter channel input source switching signal output
60STK MUTEOPower amplifier and sub woofer amplifier on/off control signal output
61SURR RELAYOsurround speakers relay drive signal output
62VCC–Power supply (+3.3V)
63NO USEONot used (connected ground)
64VSS–Ground
65CTR RELAYOcenter speaker relay drive signal output
66FR SPK RELAYOFront speakers relay drive signal output
67PROTECTORISpeaker protect detection signal input
68OVER VOLTAGE DETIPower amplifier over voltage protection detection input
69UNDER VOLTAGE DETIPower amplifier under voltage protection detection input
70THERMAL VACSIThermal VACS detection input
71TC-MUTEOTape playback muting signal output
72HP MUTEOHeadphone muting signal output
73DISPLAY-KEYIDISPLAY key press detection signal (Interrupt input)
74POWER-KEYIPOWER key press detection signal (Interrupt input)
75SW-MUTEOSubwoofer muting signal output
76LINE MUTEOLine muting signal output
77DVD A MUTEODVD analog muting signal output
78ANALOG IN MUTEOAnalog input muting signal output
79AUDIO1 IC DATAOSerial data output to M61529FP
80AUDIO1 IC CLKOSerial data transfer clock signal output to M61529FP
81VOL IC DATAOSerial data output to M61530FP
82VOL IC CLKOSerial data transfer clock signal output to M61530FP
83LINE OUTMUTEOLine Out muting signal output
84HP DETECTIHeadphone connection detection signal input
85MIC DETECTIMicrophone connection detection signal input
86MTK POWEROPower supply control signal to DVD Motherboard
87VIDEO OUT SWOComposite video output switching signal output
88V MUTEOVideo muting signal output
89A SHUTIShut off detection signal input from deck A reel pulse (A/D input)
90B SHUTIShut off detection signal input from deck B reel pulse (A/D input)
91B HALFI
92MODEL-INIModel setting input
93DEST-INIDestination setting input
94MIC LEVEL ININot used (Open)
953.3V MNTIPower supply +3.3V monitor input from DVD Motherboard
96AVSS–Ground
97BPM DETISpeana Low frequency output monitor input (A/D input)
98VREFIA/D Converter reference voltage input
Deck B cassette detection, forward side recording tab detection and reverse side
recording tab detection signal input (A/D input)
71
Page 72
HCD-GNV99D/GNV111D
Pin No.Pin NameI/ODescription
99AVCC–Power supply (+3.3V)
100SOFT TESTINot used (Open)
IC902 MB90M407PF-G-145E1 (DISPLAY CONTROL ) (PANEL Board)
Pin No.Pin NameI/ODescription
1 to 8G8 to G1OFLD grid output
9, 10P1, P2OFLD segment output
11VSS-IO–Ground
12 to 22P3 to P13OFLD segment output
23VDD-FIP–Power supply (+3.3V)
24 to 41P14 to P31OFLD segment output
42VSS-IO–Ground
43 to 47P32 to P36OFLD segment output
48VKK–Power supply (-35V)
49MD0ISetting terminal for system mode (pull up with resistor)
50MD1/VDD-VFTISetting terminal for system mode (pull up with resistor)
51MD2ISetting terminal for system mode (pull down with resistor)
52LED CD/DVDOLED drive signal output
53LED TUNEROLED drive signal output
54LED TAPEOLED drive signal output
55LED TV/SATOLED drive signal output
56LED STOP, PAUSEOLED drive signal output
57LED VOLUME 2, 3OLED drive signal output
58LED VOLUME 4, 5OLED drive signal output
59LED VOLUME 6OLED drive signal output
60IIC-DATAI/OIIC serial data input/output
61IIC-CLKI/OIIC clock signal input/output
62AVCC–Power supply (+3.3V)
63AVSS–Ground
64 to 66KEY0 to KEY2IKey input (A/D)
67ALL BANDISpectrum analyzer all band signal input
68 to 71BPF3 to BPF0ISpectrum analyzer BPF signal input
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• The mechanical parts with no reference number
in the exploded views are not supplied.
SECTION 8
EXPLODED VIEWS
• Hardware (# mark) list and accessories are
given in the last of this parts list.
•Abbreviation
AUS: Australian model
E2 : 120V AC Area in E model
E3 : 240V AC Area in E model
E15 : Iran model
EA : Saudi Arabia model
MY : Malaysia model
PH : Philippines model
SP : Singapore model
HCD-GNV99D/GNV111D
The components identified by mark 0 or
dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
51X-2050-302-1 FRONT PANEL ASSY (GNV99D)
51X-2050-303-1 FRONT PANEL ASSY (GNV111D)
522-342-128-01 ESCUTHEON (LID)
532-342-108-01 LID (TC)
542-342-134-01 SPRING (LID)
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
•Abbreviation
AUS: Australian model
E2 : 120V AC Area in E model
E3 : 240V AC Area in E model
E15 : Iran model
EA : Saudi Arabia model
MY : Malaysia model
PH : Philippines model
SP : Singapore model
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
When indicating parts by reference
number, please include the board.
OFF)
(GNV111D)
C11461-162-964-11 CERAMIC CHIP0.001uF10%50V
(GNV111D)
< RESISTOR >
R11491-216-837-11 METAL CHIP22K5%1/10W
(GNV111D)
R11501-216-835-11 METAL CHIP15K5%1/10W
(GNV111D)
R11511-216-833-11 METAL CHIP10K5%1/10W
(GNV111D)
R11521-218-867-11 METAL CHIP6.8K0.5%1/10W
(GNV111D)
R11531-216-829-11 METAL CHIP4.7K5%1/10W
(GNV111D)
R11541-216-827-11 METAL CHIP3.3K5%1/10W
(GNV111D)
R11551-216-825-11 METAL CHIP2.2K5%1/10W
(GNV111D)
R11691-216-817-11 METAL CHIP4705%1/10W
R11701-218-867-11 METAL CHIP6.8K0.5%1/10W
(GNV111D)
R11711-216-823-11 METAL CHIP1.5K5%1/10W
R11721-216-823-11 METAL CHIP1.5K5%1/10W
R11731-216-821-11 METAL CHIP1K5%1/10W
R11741-216-819-11 METAL CHIP6805%1/10W
R11931-216-821-11 METAL CHIP1K5%1/10W
IC1046-705-929-01 IC K4S641632H-UC75T
IC1056-702-302-01 IC TK11133CSCL-G
IC1068-759-667-18 IC PQ018EZ01ZP
IC1076-702-302-01 IC TK11133CSCL-G
IC2016-704-524-01 IC FAN8036L
IC3016-704-222-01 IC AK4358VQ-L
IC3601 6-707-608-01 IC PCM1803DBR
IC3711 8-759-359-49 IC NJM3414AV (TE2)
IC3731 8-759-359-49 IC NJM3414AV (TE2)
IC3751 8-759-359-49 IC NJM3414AV (TE2)
R1011-216-809-11 METAL CHIP1005%1/10W
R1041-216-864-11 SHORT CHIP0
R1051-216-833-11 METAL CHIP10K5%1/10W
R1061-216-833-11 METAL CHIP10K5%1/10W
R1071-216-833-11 METAL CHIP10K5%1/10W
R1081-216-857-11 METAL CHIP1M5%1/10W
R1091-216-864-11 SHORT CHIP0
R1101-216-841-11 METAL CHIP47K5%1/10W
R1111-216-809-11 METAL CHIP1005%1/10W
R1121-211-977-11 METAL CHIP220.5%1/10W
R1131-211-977-11 METAL CHIP220.5%1/10W
R1141-216-845-11 METAL CHIP100K5%1/10W
R1151-211-977-11 METAL CHIP220.5%1/10W
R1161-216-821-11 METAL CHIP1K5%1/10W
R1171-216-841-11 METAL CHIP47K5%1/10W
R1181-216-801-11 METAL CHIP225%1/10W
R1201-216-801-11 METAL CHIP225%1/10W
R1211-216-801-11 METAL CHIP225%1/10W
R1231-216-864-11 SHORT CHIP0
R1241-216-841-11 METAL CHIP47K5%1/10W
New part of EEPROM (IC103) on the DMB10 board can not be used. Therefore, if the mounted DMB10
board (A-1099-272-A or A-1099-344-A or A-1115-347-A) is replaced, exchange new EEPROM with
that used before the replacement.
R1261-216-864-11 SHORT CHIP0
R1331-216-827-11 METAL CHIP3.3K5%1/10W
R1341-216-827-11 METAL CHIP3.3K5%1/10W
R1351-216-827-11 METAL CHIP3.3K5%1/10W
R1361-216-835-11 METAL CHIP15K5%1/10W
R1381-216-845-11 METAL CHIP100K5%1/10W
R1411-218-916-11 METAL CHIP750K0.5%1/10W
R1421-216-845-11 METAL CHIP100K5%1/10W
R1431-216-809-11 METAL CHIP1005%1/10W
R1441-216-864-11 SHORT CHIP0
R1461-216-805-11 METAL CHIP475%1/10W
R1511-216-805-11 METAL CHIP475%1/10W
R1521-216-864-11 SHORT CHIP0
R1531-216-805-11 METAL CHIP475%1/10W
R1551-216-805-11 METAL CHIP475%1/10W
R1601-216-805-11 METAL CHIP475%1/10W
R1611-216-809-11 METAL CHIP1005%1/10W
R1641-216-809-11 METAL CHIP1005%1/10W
R1691-216-833-11 METAL CHIP10K5%1/10W
R1871-216-864-11 SHORT CHIP0
R1891-218-827-11 METAL CHIP1500.5%1/10W
R1901-218-827-11 METAL CHIP1500.5%1/10W
R1911-216-821-11 METAL CHIP1K5%1/10W
R1921-218-827-11 METAL CHIP1500.5%1/10W
R1931-216-821-11 METAL CHIP1K5%1/10W
R1951-218-827-11 METAL CHIP1500.5%1/10W
R1961-216-864-11 SHORT CHIP0
R1971-218-827-11 METAL CHIP1500.5%1/10W
R2041-216-822-11 METAL CHIP1.2K5%1/10W
R2051-216-833-11 METAL CHIP10K5%1/10W
R2061-216-833-11 METAL CHIP10K5%1/10W
R2071-216-826-11 METAL CHIP2.7K5%1/10W
R2081-216-839-11 METAL CHIP33K5%1/10W
R2091-216-839-11 METAL CHIP33K5%1/10W
R2101-216-841-11 METAL CHIP47K5%1/10W
R2121-216-833-11 METAL CHIP10K5%1/10W
R2131-218-867-11 METAL CHIP6.8K0.5%1/10W
R2141-216-835-11 METAL CHIP15K5%1/10W
R2151-216-834-11 METAL CHIP12K5%1/10W
R2161-216-834-11 METAL CHIP12K5%1/10W
R2191-216-838-11 METAL CHIP27K5%1/10W
R2201-216-833-11 METAL CHIP10K5%1/10W
R2211-218-889-11 METAL CHIP56K0.5%1/10W
R2231-218-895-11 METAL CHIP100K0.5%1/10W
R2241-216-833-11 METAL CHIP10K5%1/10W
R2251-218-895-11 METAL CHIP100K0.5%1/10W
R2261-218-889-11 METAL CHIP56K0.5%1/10W
R2301-218-893-11 METAL CHIP82K0.5%1/10W
R2311-218-875-11 METAL CHIP15K0.5%1/10W
R2321-218-877-11 METAL CHIP18K0.5%1/10W
R2331-218-883-11 METAL CHIP33K0.5%1/10W
R2341-216-833-11 METAL CHIP10K5%1/10W
R2461-216-829-11 METAL CHIP4.7K5%1/10W
R2471-216-821-11 METAL CHIP1K5%1/10W
R3081-216-864-11 SHORT CHIP0
R3141-216-809-11 METAL CHIP1005%1/10W
R3191-216-864-11 SHORT CHIP0
R11011-216-825-11 METAL CHIP2.2K5%1/10W
Ref. No.Part No.DescriptionRemarks
R11021-218-827-11 METAL CHIP1500.5%1/10W
R11031-216-833-11 METAL CHIP10K5%1/10W
R11041-216-833-11 METAL CHIP10K5%1/10W
R11051-216-833-11 METAL CHIP10K5%1/10W
R11071-216-864-11 SHORT CHIP0
R11081-216-833-11 METAL CHIP10K5%1/10W
R11091-216-864-11 SHORT CHIP0
R11101-216-826-11 METAL CHIP2.7K5%1/10W
R11111-216-864-11 SHORT CHIP0
R11201-216-864-11 SHORT CHIP0
R11211-216-864-11 SHORT CHIP0
R11221-216-864-11 SHORT CHIP0
R11231-216-864-11 SHORT CHIP0
R11241-216-864-11 SHORT CHIP0
R11251-216-864-11 SHORT CHIP0
R11291-216-845-11 METAL CHIP100K5%1/10W
R11331-216-864-11 SHORT CHIP0
R11341-216-864-11 SHORT CHIP0
R11501-216-827-11 METAL CHIP3.3K5%1/10W
R11511-216-827-11 METAL CHIP3.3K5%1/10W
R11521-216-827-11 METAL CHIP3.3K5%1/10W
R11681-216-817-11 METAL CHIP4705%1/10W
R15021-216-864-11 SHORT CHIP0
R15041-216-864-11 SHORT CHIP0
R15241-216-864-11 SHORT CHIP0
R15261-216-864-11 SHORT CHIP0
R15271-216-864-11 SHORT CHIP0
R15301-216-864-11 SHORT CHIP0
R15311-216-864-11 SHORT CHIP0
R15401-216-829-11 METAL CHIP4.7K5%1/10W
R15421-216-833-11 METAL CHIP10K5%1/10W
R15431-216-833-11 METAL CHIP10K5%1/10W
R15441-216-864-11 SHORT CHIP0
R15461-216-827-11 METAL CHIP3.3K5%1/10W
R15471-216-829-11 METAL CHIP4.7K5%1/10W
R15481-216-829-11 METAL CHIP4.7K5%1/10W
R15491-216-829-11 METAL CHIP4.7K5%1/10W
R15501-216-829-11 METAL CHIP4.7K5%1/10W
R15511-216-829-11 METAL CHIP4.7K5%1/10W
R15531-216-864-11 SHORT CHIP0
R15541-216-829-11 METAL CHIP4.7K5%1/10W
R15551-216-829-11 METAL CHIP4.7K5%1/10W
R15571-216-809-11 METAL CHIP1005%1/10W
R25041-216-829-11 METAL CHIP4.7K5%1/10W
R35011-216-864-11 SHORT CHIP0
R36011-216-809-11 METAL CHIP1005%1/10W
R36021-216-809-11 METAL CHIP1005%1/10W
R36031-216-833-11 METAL CHIP10K5%1/10W
R36051-216-864-11 SHORT CHIP0
R36061-216-864-11 SHORT CHIP0
R36071-216-864-11 SHORT CHIP0
R36091-216-864-11 SHORT CHIP0
R36111-216-809-11 METAL CHIP1005%1/10W
R36211-216-809-11 METAL CHIP1005%1/10W
R36511-216-864-11 SHORT CHIP0
R36521-216-864-11 SHORT CHIP0
R36531-216-864-11 SHORT CHIP0
R37111-216-823-11 METAL CHIP1.5K5%1/10W
R37121-216-823-11 METAL CHIP1.5K5%1/10W
R37131-216-828-11 METAL CHIP3.9K5%1/10W
R37141-216-828-11 METAL CHIP3.9K5%1/10W
R37151-216-829-11 METAL CHIP4.7K5%1/10W
R37161-216-821-11 METAL CHIP1K5%1/10W
R37171-216-821-11 METAL CHIP1K5%1/10W
R37181-216-829-11 METAL CHIP4.7K5%1/10W
R37191-216-821-11 METAL CHIP1K5%1/10W
R37211-216-823-11 METAL CHIP1.5K5%1/10W
R37221-216-823-11 METAL CHIP1.5K5%1/10W
R37231-216-828-11 METAL CHIP3.9K5%1/10W
R37241-216-828-11 METAL CHIP3.9K5%1/10W
R37251-216-829-11 METAL CHIP4.7K5%1/10W
R37261-216-821-11 METAL CHIP1K5%1/10W
R37271-216-821-11 METAL CHIP1K5%1/10W
R37281-216-829-11 METAL CHIP4.7K5%1/10W
R37291-216-821-11 METAL CHIP1K5%1/10W
R37311-216-823-11 METAL CHIP1.5K5%1/10W
R37321-216-823-11 METAL CHIP1.5K5%1/10W
R37331-216-828-11 METAL CHIP3.9K5%1/10W
R37341-216-828-11 METAL CHIP3.9K5%1/10W
R37351-216-829-11 METAL CHIP4.7K5%1/10W
R37361-216-821-11 METAL CHIP1K5%1/10W
R37371-216-821-11 METAL CHIP1K5%1/10W
R37381-216-829-11 METAL CHIP4.7K5%1/10W
R37391-216-821-11 METAL CHIP1K5%1/10W
R37411-216-823-11 METAL CHIP1.5K5%1/10W
R37421-216-823-11 METAL CHIP1.5K5%1/10W
R37431-216-828-11 METAL CHIP3.9K5%1/10W
R37441-216-828-11 METAL CHIP3.9K5%1/10W
R37451-216-829-11 METAL CHIP4.7K5%1/10W
R37461-216-821-11 METAL CHIP1K5%1/10W
R37471-216-821-11 METAL CHIP1K5%1/10W
R37481-216-829-11 METAL CHIP4.7K5%1/10W
R37491-216-821-11 METAL CHIP1K5%1/10W
R37511-216-823-11 METAL CHIP1.5K5%1/10W
R37521-216-823-11 METAL CHIP1.5K5%1/10W
R37531-216-828-11 METAL CHIP3.9K5%1/10W
R37541-216-828-11 METAL CHIP3.9K5%1/10W
R37551-216-829-11 METAL CHIP4.7K5%1/10W
R37561-216-821-11 METAL CHIP1K5%1/10W
R37571-216-821-11 METAL CHIP1K5%1/10W
R37581-216-829-11 METAL CHIP4.7K5%1/10W
R37591-216-821-11 METAL CHIP1K5%1/10W
R37751-216-829-11 METAL CHIP4.7K5%1/10W
R37761-216-821-11 METAL CHIP1K5%1/10W
R37771-216-821-11 METAL CHIP1K5%1/10W
R37781-216-829-11 METAL CHIP4.7K5%1/10W
R37791-216-821-11 METAL CHIP1K5%1/10W
R37811-216-823-11 METAL CHIP1.5K5%1/10W
R37821-216-823-11 METAL CHIP1.5K5%1/10W
R37831-216-828-11 METAL CHIP3.9K5%1/10W
R37841-216-828-11 METAL CHIP3.9K5%1/10W
R37851-216-829-11 METAL CHIP4.7K5%1/10W
R37861-216-821-11 METAL CHIP1K5%1/10W
R37871-216-821-11 METAL CHIP1K5%1/10W
R37881-216-829-11 METAL CHIP4.7K5%1/10W
R37891-216-821-11 METAL CHIP1K5%1/10W
R38011-216-864-11 SHORT CHIP0
R38021-216-864-11 SHORT CHIP0
R38031-216-833-11 METAL CHIP10K5%1/10W
R38041-216-836-11 METAL CHIP18K5%1/10W
R38051-216-821-11 METAL CHIP1K5%1/10W
R47011-216-864-11 SHORT CHIP0
R47021-216-864-11 SHORT CHIP0
R47031-216-864-11 SHORT CHIP0
R47041-216-864-11 SHORT CHIP0
R47051-216-864-11 SHORT CHIP0
R47061-216-864-11 SHORT CHIP0
R37611-216-823-11 METAL CHIP1.5K5%1/10W
R37621-216-823-11 METAL CHIP1.5K5%1/10W
R37631-216-828-11 METAL CHIP3.9K5%1/10W
R37641-216-828-11 METAL CHIP3.9K5%1/10W
R37651-216-829-11 METAL CHIP4.7K5%1/10W
R37661-216-821-11 METAL CHIP1K5%1/10W
R37671-216-821-11 METAL CHIP1K5%1/10W
R37681-216-829-11 METAL CHIP4.7K5%1/10W
R37691-216-821-11 METAL CHIP1K5%1/10W
R37711-216-823-11 METAL CHIP1.5K5%1/10W
R37721-216-823-11 METAL CHIP1.5K5%1/10W
R37731-216-828-11 METAL CHIP3.9K5%1/10W
R37741-216-828-11 METAL CHIP3.9K5%1/10W
R7001-216-821-11 METAL CHIP1K5%1/10W
R7011-216-841-11 METAL CHIP47K5%1/10W
R7021-216-808-11 METAL CHIP825%1/10W
(GNV111D: EXCEPT E2)
R7021-216-812-11 METAL CHIP1805%1/10W
(E2)
R7021-216-815-11 METAL CHIP3305%1/10W
(GNV99D)
R7271-216-839-11 METAL CHIP33K5%1/10W
(GNV111D)
0R7301-234-499-21 ENCAPSULATED COMPONENT
R7311-216-821-11 METAL CHIP1K5%1/10W
R7321-216-838-11 METAL CHIP27K5%1/10W
R7331-216-845-11 METAL CHIP100K5%1/10W
R7341-216-842-11 METAL CHIP56K5%1/10W
R7351-245-711-31 CARBON105%1/2W
R7361-245-711-31 CARBON105%1/2W
R7371-245-711-31 CARBON105%1/2W
R7401-216-821-11 METAL CHIP1K5%1/10W
R7411-216-841-11 METAL CHIP47K5%1/10W
R7421-216-808-11 METAL CHIP825%1/10W
(GNV111D: EXCEPT E2)
R7421-216-812-11 METAL CHIP1805%1/10W
(E2)
R7421-216-815-11 METAL CHIP3305%1/10W
(GNV99D)
R7431-216-821-11 METAL CHIP1K5%1/10W
R7441-216-833-11 METAL CHIP10K5%1/10W
R7451-216-841-11 METAL CHIP47K5%1/10W
R7461-216-833-11 METAL CHIP10K5%1/10W
R7471-218-867-11 METAL CHIP6.8K0.5%1/10W
R7481-216-832-11 METAL CHIP8.2K5%1/10W
R7491-216-833-11 METAL CHIP10K5%1/10W
R7501-216-821-11 METAL CHIP1K5%1/10W
R7511-216-841-11 METAL CHIP47K5%1/10W
R7521-216-808-11 METAL CHIP825%1/10W
(GNV111D: EXCEPT E2)
R7521-216-812-11 METAL CHIP1805%1/10W
(E2)
R7521-216-815-11 METAL CHIP3305%1/10W
(GNV99D)
R7531-216-821-11 METAL CHIP1K5%1/10W
R7541-216-833-11 METAL CHIP10K5%1/10W
R7551-216-841-11 METAL CHIP47K5%1/10W
R7561-216-833-11 METAL CHIP10K5%1/10W
R7571-216-825-11 METAL CHIP2.2K5%1/10W
R7031-216-821-11 METAL CHIP1K5%1/10W
R7041-216-833-11 METAL CHIP10K5%1/10W
R7051-216-841-11 METAL CHIP47K5%1/10W
R7061-216-833-11 METAL CHIP10K5%1/10W
R7101-216-841-11 METAL CHIP47K5%1/10W
R7111-216-841-11 METAL CHIP47K5%1/10W
R7121-216-841-11 METAL CHIP47K5%1/10W
R7201-216-833-11 METAL CHIP10K5%1/10W
(GNV111D)
R7211-216-833-11 METAL CHIP10K5%1/10W
(GNV111D)
R7221-216-837-11 METAL CHIP22K5%1/10W
(GNV111D)
R7231-216-825-11 METAL CHIP2.2K5%1/10W
(GNV111D)
R7241-216-839-11 METAL CHIP33K5%1/10W
(GNV111D)
R7251-216-841-11 METAL CHIP47K5%1/10W
(GNV111D)
R7261-216-839-11 METAL CHIP33K5%1/10W
(GNV111D)
84
R7601-216-809-11 METAL CHIP1005%1/10W
R7611-216-839-11 METAL CHIP33K5%1/10W
(GNV99D)
R7611-216-845-11 METAL CHIP100K5%1/10W
(GNV111D)
R7621-216-839-11 METAL CHIP33K5%1/10W
(GNV99D)
R7621-216-845-11 METAL CHIP100K5%1/10W
(GNV111D)
R7641-260-087-11 CARBON1005%1/2W
R7651-260-087-11 CARBON1005%1/2W
R7661-216-825-11 METAL CHIP2.2K5%1/10W
R7671-216-837-11 METAL CHIP22K5%1/10W
R7681-216-825-11 METAL CHIP2.2K5%1/10W
R7691-216-837-11 METAL CHIP22K5%1/10W
0R7701-234-499-21 ENCAPSULATED COMPONENT
R7711-216-821-11 METAL CHIP1K5%1/10W
R7721-216-838-11 METAL CHIP27K5%1/10W
R7731-216-845-11 METAL CHIP100K5%1/10W
R7741-216-843-11 METAL CHIP68K5%1/10W
R7751-245-711-31 CARBON105%1/2W
R11381-216-820-11 METAL CHIP8205%1/10W
R11391-216-820-11 METAL CHIP8205%1/10W
R11401-216-820-11 METAL CHIP8205%1/10W
R11441-216-820-11 METAL CHIP8205%1/10W
R11451-216-820-11 METAL CHIP8205%1/10W
R11461-216-820-11 METAL CHIP8205%1/10W
R11561-216-821-11 METAL CHIP1K5%1/10W
R11571-216-820-11 METAL CHIP8205%1/10W
R11581-216-820-11 METAL CHIP8205%1/10W
R11591-216-820-11 METAL CHIP8205%1/10W
R11901-216-809-11 METAL CHIP1005%1/10W
R11911-216-809-11 METAL CHIP1005%1/10W
R11921-216-809-11 METAL CHIP1005%1/10W
FB2041-216-864-11 SHORT CHIP0
FB2541-216-864-11 SHORT CHIP0
FB2601-216-864-11 SHORT CHIP0
FB2611-216-864-11 SHORT CHIP0
< IC >
IC1016-703-650-11 IC M61529FP-D60G
IC2016-703-651-11 IC M61530FP-D60G
IC3016-702-130-01 IC HA12237F
IC3048-759-710-97 IC NJM4565M-D
IC4016-805-073-01 IC M30620MCP-A03FPU0
JR5051-216-864-11 SHORT CHIP0
JR5061-216-864-11 SHORT CHIP0
JR5071-216-296-11 SHORT CHIP0
JR5081-216-864-11 SHORT CHIP0
JR5091-216-864-11 SHORT CHIP0
JR5101-216-864-11 SHORT CHIP0
JR5111-216-864-11 SHORT CHIP0
IC5016-705-809-01 IC BD4929G-TR
IC5078-759-198-03 IC PQ09RF21
IC5506-703-610-01 IC RT8H015C-T112-1
IC5586-703-547-01 IC TA7805LS
IC5596-702-771-01 IC TA78033LS
IC5608-759-701-59 IC NJM78M09FA
IC5618-759-701-59 IC NJM78M09FA
R1011-216-825-11 METAL CHIP2.2K5%1/10W
R1021-216-833-11 METAL CHIP10K5%1/10W
R1031-216-818-11 METAL CHIP5605%1/10W
R1041-216-821-11 METAL CHIP1K5%1/10W
R1051-216-841-11 METAL CHIP47K5%1/10W
R1061-216-833-11 METAL CHIP10K5%1/10W
R1071-216-809-11 METAL CHIP1005%1/10W
R1081-218-867-11 METAL CHIP6.8K0.5%1/10W
R1091-216-827-11 METAL CHIP3.3K5%1/10W
R1101-216-833-11 METAL CHIP10K5%1/10W
R1111-216-833-11 METAL CHIP10K5%1/10W
R1121-216-841-11 METAL CHIP47K5%1/10W
R1131-216-833-11 METAL CHIP10K5%1/10W
R1141-216-833-11 METAL CHIP10K5%1/10W
R1151-216-821-11 METAL CHIP1K5%1/10W
R1161-216-809-11 METAL CHIP1005%1/10W
R1171-216-864-11 SHORT CHIP0
R1211-216-821-11 METAL CHIP1K5%1/10W
R1221-216-821-11 METAL CHIP1K5%1/10W
R1301-216-825-11 METAL CHIP2.2K5%1/10W
R1311-216-825-11 METAL CHIP2.2K5%1/10W
R1321-216-857-11 METAL CHIP1M5%1/10W
R1331-216-845-11 METAL CHIP100K5%1/10W
R1351-216-825-11 METAL CHIP2.2K5%1/10W
R1501-216-825-11 METAL CHIP2.2K5%1/10W
R1511-216-825-11 METAL CHIP2.2K5%1/10W
R1521-216-833-11 METAL CHIP10K5%1/10W
R1531-216-818-11 METAL CHIP5605%1/10W
R1541-216-821-11 METAL CHIP1K5%1/10W
R1551-216-841-11 METAL CHIP47K5%1/10W
R1561-216-833-11 METAL CHIP10K5%1/10W
R1571-216-809-11 METAL CHIP1005%1/10W
R1581-218-867-11 METAL CHIP6.8K0.5%1/10W
R1591-216-827-11 METAL CHIP3.3K5%1/10W
R1601-216-833-11 METAL CHIP10K5%1/10W
R1611-216-833-11 METAL CHIP10K5%1/10W
R1621-216-841-11 METAL CHIP47K5%1/10W
R1631-216-833-11 METAL CHIP10K5%1/10W
R1641-216-833-11 METAL CHIP10K5%1/10W
R1651-216-821-11 METAL CHIP1K5%1/10W
R1661-216-809-11 METAL CHIP1005%1/10W
R1671-216-864-11 SHORT CHIP0
R2001-216-825-11 METAL CHIP2.2K5%1/10W
R2021-216-833-11 METAL CHIP10K5%1/10W
R2031-216-833-11 METAL CHIP10K5%1/10W
R2041-216-821-11 METAL CHIP1K5%1/10W
R2051-216-818-11 METAL CHIP5605%1/10W
R2061-216-841-11 METAL CHIP47K5%1/10W
R2071-216-825-11 METAL CHIP2.2K5%1/10W
R2081-216-825-11 METAL CHIP2.2K5%1/10W
R2091-216-833-11 METAL CHIP10K5%1/10W
R2101-216-817-11 METAL CHIP4705%1/10W
R2111-216-841-11 METAL CHIP47K5%1/10W
R2121-216-832-11 METAL CHIP8.2K5%1/10W
R2131-218-867-11 METAL CHIP6.8K0.5%1/10W
R2141-216-841-11 METAL CHIP47K5%1/10W
R2151-216-829-11 METAL CHIP4.7K5%1/10W
R2161-216-825-11 METAL CHIP2.2K5%1/10W
R2171-216-833-11 METAL CHIP10K5%1/10W
R2181-216-829-11 METAL CHIP4.7K5%1/10W
R2191-216-825-11 METAL CHIP2.2K5%1/10W
R2201-216-833-11 METAL CHIP10K5%1/10W
R2211-216-841-11 METAL CHIP47K5%1/10W
R2221-216-821-11 METAL CHIP1K5%1/10W
R2231-216-832-11 METAL CHIP8.2K5%1/10W
R2241-216-821-11 METAL CHIP1K5%1/10W
R2251-216-833-11 METAL CHIP10K5%1/10W
R2261-216-837-11 METAL CHIP22K5%1/10W
R2271-216-841-11 METAL CHIP47K5%1/10W
R2281-216-821-11 METAL CHIP1K5%1/10W
R2291-216-833-11 METAL CHIP10K5%1/10W
R2301-216-821-11 METAL CHIP1K5%1/10W
R2311-216-841-11 METAL CHIP47K5%1/10W
R2321-216-833-11 METAL CHIP10K5%1/10W
R2331-216-841-11 METAL CHIP47K5%1/10W
R2341-216-821-11 METAL CHIP1K5%1/10W
R2351-216-833-11 METAL CHIP10K5%1/10W
R2361-216-833-11 METAL CHIP10K5%1/10W
R2371-216-841-11 METAL CHIP47K5%1/10W
R2381-216-864-11 SHORT CHIP0
R2391-216-833-11 METAL CHIP10K5%1/10W
R2401-216-835-11 METAL CHIP15K5%1/10W
R2411-216-839-11 METAL CHIP33K5%1/10W
R2421-216-833-11 METAL CHIP10K5%1/10W
R2431-216-821-11 METAL CHIP1K5%1/10W
R2441-216-845-11 METAL CHIP100K5%1/10W
R2451-216-833-11 METAL CHIP10K5%1/10W
R2461-216-841-11 METAL CHIP47K5%1/10W
R2471-216-821-11 METAL CHIP1K5%1/10W
R2481-216-845-11 METAL CHIP100K5%1/10W
R2491-216-833-11 METAL CHIP10K5%1/10W
R2501-216-839-11 METAL CHIP33K5%1/10W
R2511-216-825-11 METAL CHIP2.2K5%1/10W
R2521-216-833-11 METAL CHIP10K5%1/10W
R2531-216-845-11 METAL CHIP100K5%1/10W
R2541-216-827-11 METAL CHIP3.3K5%1/10W
R2551-216-818-11 METAL CHIP5605%1/10W
R2561-216-841-11 METAL CHIP47K5%1/10W
R2571-216-825-11 METAL CHIP2.2K5%1/10W
R2581-216-825-11 METAL CHIP2.2K5%1/10W
R2591-216-833-11 METAL CHIP10K5%1/10W
R2601-216-817-11 METAL CHIP4705%1/10W
R2611-216-841-11 METAL CHIP47K5%1/10W
R2621-216-832-11 METAL CHIP8.2K5%1/10W
R2631-218-867-11 METAL CHIP6.8K0.5%1/10W
R2641-216-841-11 METAL CHIP47K5%1/10W
R2651-216-829-11 METAL CHIP4.7K5%1/10W
R2661-216-825-11 METAL CHIP2.2K5%1/10W
R2671-216-833-11 METAL CHIP10K5%1/10W
R2681-216-821-11 METAL CHIP1K5%1/10W
R2691-216-833-11 METAL CHIP10K5%1/10W
R2701-216-841-11 METAL CHIP47K5%1/10W
R2711-216-833-11 METAL CHIP10K5%1/10W
R2721-216-827-11 METAL CHIP3.3K5%1/10W
R2731-216-833-11 METAL CHIP10K5%1/10W
R2741-216-821-11 METAL CHIP1K5%1/10W
R2751-216-833-11 METAL CHIP10K5%1/10W
R2761-216-837-11 METAL CHIP22K5%1/10W
R2771-216-841-11 METAL CHIP47K5%1/10W
R2781-216-821-11 METAL CHIP1K5%1/10W
R2791-216-833-11 METAL CHIP10K5%1/10W
R2801-216-821-11 METAL CHIP1K5%1/10W
R2811-216-841-11 METAL CHIP47K5%1/10W
R2821-216-833-11 METAL CHIP10K5%1/10W
R2831-216-841-11 METAL CHIP47K5%1/10W
R2841-216-821-11 METAL CHIP1K5%1/10W
R2851-216-833-11 METAL CHIP10K5%1/10W
R2861-216-833-11 METAL CHIP10K5%1/10W
R2871-216-841-11 METAL CHIP47K5%1/10W
R2881-216-864-11 SHORT CHIP0
R2891-216-833-11 METAL CHIP10K5%1/10W
R2901-216-835-11 METAL CHIP15K5%1/10W
R2911-216-839-11 METAL CHIP33K5%1/10W
R2921-216-833-11 METAL CHIP10K5%1/10W
R2931-216-821-11 METAL CHIP1K5%1/10W
R2941-216-845-11 METAL CHIP100K5%1/10W
R2951-216-833-11 METAL CHIP10K5%1/10W
R2961-216-841-11 METAL CHIP47K5%1/10W
R2971-216-821-11 METAL CHIP1K5%1/10W
R2981-216-833-11 METAL CHIP10K5%1/10W
R2991-216-833-11 METAL CHIP10K5%1/10W
R3001-216-841-11 METAL CHIP47K5%1/10W
R3011-216-825-11 METAL CHIP2.2K5%1/10W
R3021-216-829-11 METAL CHIP4.7K5%1/10W
R3031-216-833-11 METAL CHIP10K5%1/10W
R3041-216-825-11 METAL CHIP2.2K5%1/10W
R3051-216-841-11 METAL CHIP47K5%1/10W
R3061-216-837-11 METAL CHIP22K5%1/10W
R3071-216-857-11 METAL CHIP1M5%1/10W
R3081-216-809-11 METAL CHIP1005%1/10W
R3091-216-829-11 METAL CHIP4.7K5%1/10W
R3101-216-809-11 METAL CHIP1005%1/10W
R3111-216-809-11 METAL CHIP1005%1/10W
R3121-216-809-11 METAL CHIP1005%1/10W
R3131-216-841-11 METAL CHIP47K5%1/10W
R3141-216-825-11 METAL CHIP2.2K5%1/10W
R3151-216-829-11 METAL CHIP4.7K5%1/10W
R3161-216-837-11 METAL CHIP22K5%1/10W
R3171-216-833-11 METAL CHIP10K5%1/10W
R3181-216-825-11 METAL CHIP2.2K5%1/10W
R3191-216-825-11 METAL CHIP2.2K5%1/10W
R3351-216-825-11 METAL CHIP2.2K5%1/10W
R3361-216-825-11 METAL CHIP2.2K5%1/10W
R3371-216-825-11 METAL CHIP2.2K5%1/10W
R3381-216-833-11 METAL CHIP10K5%1/10W
R3391-216-836-11 METAL CHIP18K5%1/10W
R3401-216-825-11 METAL CHIP2.2K5%1/10W
R3411-216-827-11 METAL CHIP3.3K5%1/10W
R3421-216-825-11 METAL CHIP2.2K5%1/10W
R3431-216-825-11 METAL CHIP2.2K5%1/10W
R3441-216-819-11 METAL CHIP6805%1/10W
R3451-216-827-11 METAL CHIP3.3K5%1/10W
R3461-216-819-11 METAL CHIP6805%1/10W
R3471-216-825-11 METAL CHIP2.2K5%1/10W
R3481-216-819-11 METAL CHIP6805%1/10W
R3491-216-827-11 METAL CHIP3.3K5%1/10W
R3501-216-841-11 METAL CHIP47K5%1/10W
R3511-216-825-11 METAL CHIP2.2K5%1/10W
R3521-216-829-11 METAL CHIP4.7K5%1/10W
R3531-216-833-11 METAL CHIP10K5%1/10W
R3541-216-825-11 METAL CHIP2.2K5%1/10W
R3551-216-841-11 METAL CHIP47K5%1/10W
R3561-216-829-11 METAL CHIP4.7K5%1/10W
R3571-216-829-11 METAL CHIP4.7K5%1/10W
R3581-216-839-11 METAL CHIP33K5%1/10W
R3591-216-839-11 METAL CHIP33K5%1/10W
R3601-216-835-11 METAL CHIP15K5%1/10W
R3611-216-835-11 METAL CHIP15K5%1/10W
R3621-216-829-11 METAL CHIP4.7K5%1/10W
R3631-216-829-11 METAL CHIP4.7K5%1/10W
R3641-216-825-11 METAL CHIP2.2K5%1/10W
R3651-216-841-11 METAL CHIP47K5%1/10W
R3661-216-829-11 METAL CHIP4.7K5%1/10W
R3671-216-841-11 METAL CHIP47K5%1/10W
R3681-216-825-11 METAL CHIP2.2K5%1/10W
R3691-216-825-11 METAL CHIP2.2K5%1/10W
R3701-216-827-11 METAL CHIP3.3K5%1/10W
R3711-216-829-11 METAL CHIP4.7K5%1/10W
R3721-216-833-11 METAL CHIP10K5%1/10W
R3731-216-829-11 METAL CHIP4.7K5%1/10W
R3741-216-829-11 METAL CHIP4.7K5%1/10W
R3751-216-833-11 METAL CHIP10K5%1/10W
R3761-216-829-11 METAL CHIP4.7K5%1/10W
R3771-216-805-11 METAL CHIP475%1/10W
R3781-216-833-11 METAL CHIP10K5%1/10W
R3791-216-797-11 METAL CHIP105%1/10W
R3801-218-867-11 METAL CHIP6.8K0.5%1/10W
R3811-216-829-11 METAL CHIP4.7K5%1/10W
R3821-216-841-11 METAL CHIP47K5%1/10W
R3831-216-815-11 METAL CHIP3305%1/10W
R3841-216-815-11 METAL CHIP3305%1/10W
R3851-216-825-11 METAL CHIP2.2K5%1/10W
R3861-216-803-11 METAL CHIP335%1/10W
R3871-216-825-11 METAL CHIP2.2K5%1/10W
R3881-216-833-11 METAL CHIP10K5%1/10W
R3891-216-836-11 METAL CHIP18K5%1/10W
R3901-216-833-11 METAL CHIP10K5%1/10W
R3911-216-825-11 METAL CHIP2.2K5%1/10W
R3921-218-867-11 METAL CHIP6.8K0.5%1/10W
R3941-216-829-11 METAL CHIP4.7K5%1/10W
R3951-216-841-11 METAL CHIP47K5%1/10W
R3961-216-833-11 METAL CHIP10K5%1/10W
R3991-216-833-11 METAL CHIP10K5%1/10W
R4001-216-833-11 METAL CHIP10K5%1/10W
R4011-216-809-11 METAL CHIP1005%1/10W
R4021-216-809-11 METAL CHIP1005%1/10W
R4031-216-833-11 METAL CHIP10K5%1/10W
R4041-216-833-11 METAL CHIP10K5%1/10W
R4051-216-809-11 METAL CHIP1005%1/10W
R4061-216-809-11 METAL CHIP1005%1/10W
R4071-216-809-11 METAL CHIP1005%1/10W
R4081-216-809-11 METAL CHIP1005%1/10W
R4091-216-809-11 METAL CHIP1005%1/10W
R4101-216-833-11 METAL CHIP10K5%1/10W
R4111-216-851-11 METAL CHIP330K5%1/10W
R4121-216-845-11 METAL CHIP100K5%1/10W
R4131-216-864-11 SHORT CHIP0
R4141-216-809-11 METAL CHIP1005%1/10W
R4151-216-809-11 METAL CHIP1005%1/10W
R4171-216-833-11 METAL CHIP10K5%1/10W
R4181-216-809-11 METAL CHIP1005%1/10W
R4191-216-841-11 METAL CHIP47K5%1/10W
R4201-216-821-11 METAL CHIP1K5%1/10W
R4211-216-809-11 METAL CHIP1005%1/10W
R4221-216-809-11 METAL CHIP1005%1/10W
R4331-216-809-11 METAL CHIP1005%1/10W
R4341-216-809-11 METAL CHIP1005%1/10W
R4351-216-809-11 METAL CHIP1005%1/10W
R4361-216-833-11 METAL CHIP10K5%1/10W
R4371-216-833-11 METAL CHIP10K5%1/10W
R4381-216-809-11 METAL CHIP1005%1/10W
R4391-216-809-11 METAL CHIP1005%1/10W
R4401-216-809-11 METAL CHIP1005%1/10W
R4411-216-809-11 METAL CHIP1005%1/10W
R4421-216-809-11 METAL CHIP1005%1/10W
R4431-216-809-11 METAL CHIP1005%1/10W
R4441-216-821-11 METAL CHIP1K5%1/10W
R4461-216-809-11 METAL CHIP1005%1/10W
R4471-216-809-11 METAL CHIP1005%1/10W
R4511-216-809-11 METAL CHIP1005%1/10W
R4521-216-809-11 METAL CHIP1005%1/10W
R4531-216-809-11 METAL CHIP1005%1/10W
R4541-216-809-11 METAL CHIP1005%1/10W
R4551-216-833-11 METAL CHIP10K5%1/10W
R4561-216-833-11 METAL CHIP10K5%1/10W
R4571-216-809-11 METAL CHIP1005%1/10W
R4581-216-809-11 METAL CHIP1005%1/10W
R4661-216-833-11 METAL CHIP10K5%1/10W
R4671-216-809-11 METAL CHIP1005%1/10W
R4681-216-809-11 METAL CHIP1005%1/10W
R4691-216-809-11 METAL CHIP1005%1/10W
R4701-216-809-11 METAL CHIP1005%1/10W
R4711-216-833-11 METAL CHIP10K5%1/10W
R4721-216-809-11 METAL CHIP1005%1/10W
R4731-216-809-11 METAL CHIP1005%1/10W
R4741-216-809-11 METAL CHIP1005%1/10W
R4751-216-809-11 METAL CHIP1005%1/10W
R4841-216-833-11 METAL CHIP10K5%1/10W
R4851-216-809-11 METAL CHIP1005%1/10W
R4861-216-809-11 METAL CHIP1005%1/10W
R4871-216-833-11 METAL CHIP10K5%1/10W
R4881-216-809-11 METAL CHIP1005%1/10W
R4891-216-809-11 METAL CHIP1005%1/10W
R4901-216-809-11 METAL CHIP1005%1/10W
R4911-216-809-11 METAL CHIP1005%1/10W
R4921-216-829-11 METAL CHIP4.7K5%1/10W
R4931-216-815-11 METAL CHIP3305%1/10W
(E3, E15)
R4931-216-821-11 METAL CHIP1K5%1/10W
(EA)
R4931-216-829-11 METAL CHIP4.7K5%1/10W
(E2)
R4931-216-864-11 SHORT CHIP0 (MY, SP, PH, AUS)
R4231-216-809-11 METAL CHIP1005%1/10W
R4241-216-809-11 METAL CHIP1005%1/10W
R4251-216-809-11 METAL CHIP1005%1/10W
R4261-216-809-11 METAL CHIP1005%1/10W
R4271-216-833-11 METAL CHIP10K5%1/10W
R4281-216-833-11 METAL CHIP10K5%1/10W
R4291-216-809-11 METAL CHIP1005%1/10W
R4301-216-809-11 METAL CHIP1005%1/10W
R4311-216-809-11 METAL CHIP1005%1/10W
R4321-216-809-11 METAL CHIP1005%1/10W
R4951-216-809-11 METAL CHIP1005%1/10W
R4971-216-809-11 METAL CHIP1005%1/10W
(GNV111D: E3, E15, EA, E2)
R5001-216-829-11 METAL CHIP4.7K5%1/10W
R5011-216-813-11 METAL CHIP2205%1/10W
R5021-216-821-11 METAL CHIP1K5%1/10W
R5031-216-864-11 SHORT CHIP0
R5051-216-826-11 METAL CHIP2.7K5%1/10W
R5061-216-829-11 METAL CHIP4.7K5%1/10W
R5071-216-833-11 METAL CHIP10K5%1/10W
R5091-216-843-11 METAL CHIP68K5%1/10W
R5101-216-835-11 METAL CHIP15K5%1/10W
R5111-216-853-11 METAL CHIP470K5%1/10W
R5121-216-843-11 METAL CHIP68K5%1/10W
R5131-216-835-11 METAL CHIP15K5%1/10W
R5141-216-853-11 METAL CHIP470K5%1/10W
R5151-216-843-11 METAL CHIP68K5%1/10W
R5161-216-835-11 METAL CHIP15K5%1/10W
R5171-216-841-11 METAL CHIP47K5%1/10W
R5181-216-833-11 METAL CHIP10K5%1/10W
R5191-216-821-11 METAL CHIP1K5%1/10W
R5201-216-833-11 METAL CHIP10K5%1/10W
R5221-216-829-11 METAL CHIP4.7K5%1/10W
R5231-216-829-11 METAL CHIP4.7K5%1/10W
R5241-216-833-11 METAL CHIP10K5%1/10W
R5251-216-833-11 METAL CHIP10K5%1/10W
R5261-216-821-11 METAL CHIP1K5%1/10W
R5271-216-841-11 METAL CHIP47K5%1/10W
R5281-216-833-11 METAL CHIP10K5%1/10W
R5291-216-835-11 METAL CHIP15K5%1/10W
R5301-216-843-11 METAL CHIP68K5%1/10W
R5311-218-867-11 METAL CHIP6.8K0.5%1/10W
R5321-216-827-11 METAL CHIP3.3K5%1/10W
R5331-216-833-11 METAL CHIP10K5%1/10W
R5341-216-833-11 METAL CHIP10K5%1/10W
R5351-216-833-11 METAL CHIP10K5%1/10W
R5361-216-833-11 METAL CHIP10K5%1/10W
R5371-216-853-11 METAL CHIP470K5%1/10W
R5381-216-830-11 METAL CHIP5.6K5%1/10W
R5391-216-829-11 METAL CHIP4.7K5%1/10W
R5401-216-833-11 METAL CHIP10K5%1/10W
R5491-216-824-11 METAL CHIP1.8K5%1/10W
R5511-216-842-11 METAL CHIP56K5%1/10W
R5521-216-843-11 METAL CHIP68K5%1/10W
R5531-216-853-11 METAL CHIP470K5%1/10W
R5541-216-835-11 METAL CHIP15K5%1/10W
R5731-216-833-11 METAL CHIP10K5%1/10W
R5741-216-833-11 METAL CHIP10K5%1/10W
R5751-216-833-11 METAL CHIP10K5%1/10W
R5761-216-821-11 METAL CHIP1K5%1/10W
R5771-216-841-11 METAL CHIP47K5%1/10W
R5781-216-833-11 METAL CHIP10K5%1/10W
R5791-216-833-11 METAL CHIP10K5%1/10W
R5801-216-833-11 METAL CHIP10K5%1/10W
R5811-218-867-11 METAL CHIP6.8K0.5%1/10W
R5821-216-827-11 METAL CHIP3.3K5%1/10W
R5831-216-841-11 METAL CHIP47K5%1/10W
R5841-216-845-11 METAL CHIP100K5%1/10W
R5851-216-829-11 METAL CHIP4.7K5%1/10W
R5861-216-833-11 METAL CHIP10K5%1/10W
R5921-216-815-11 METAL CHIP3305%1/10W
(GNV99D)
R5921-216-864-11 SHORT CHIP0 (GNV111D)
R5931-216-821-11 METAL CHIP1K5%1/10W
R5931-216-829-11 METAL CHIP4.7K5%1/10W
(EXCEPT E2)
R6021-216-833-11 METAL CHIP10K5%1/10W
R6121-218-867-11 METAL CHIP6.8K0.5%1/10W
R6231-218-867-11 METAL CHIP6.8K0.5%1/10W
R6621-218-867-11 METAL CHIP6.8K0.5%1/10W
R11211-216-835-11 METAL CHIP15K5%1/10W
R11221-216-835-11 METAL CHIP15K5%1/10W
R11231-216-835-11 METAL CHIP15K5%1/10W
R11241-216-841-11 METAL CHIP47K5%1/10W
R11251-216-825-11 METAL CHIP2.2K5%1/10W
FB1100 1-216-864-11 SHORT CHIP0
FB1101 1-216-864-11 SHORT CHIP0
< IC >
IC1100 8-759-710-97 IC NJM4565M-D
IC1101 8-759-496-41 IC M65850FP-E1
< JACK >
J11001-817-630-11 JACK (LARGE TYPE) (MIC 1)
J11011-817-630-11 JACK (LARGE TYPE) (MIC 2)
J11021-764-592-11 JACK 3P (VIDEO OUT)
J11031-794-702-11 JACK, HEADPHONE (PHONES)
< JUMPER RESISTOR >
JR1100 1-216-864-11 SHORT CHIP0
JR1101 1-216-864-11 SHORT CHIP0
JR1102 1-216-864-11 SHORT CHIP0
JR1103 1-216-296-11 SHORT CHIP0
JR1104 1-216-296-11 SHORT CHIP0
JR1105 1-216-296-11 SHORT CHIP0
JR1106 1-216-864-11 SHORT CHIP0
JR1108 1-216-864-11 SHORT CHIP0
JR1113 1-216-296-11 SHORT CHIP0
JR1114 1-216-296-11 SHORT CHIP0
< RESISTOR >
R11001-216-833-11 METAL CHIP10K5%1/10W
R11011-216-821-11 METAL CHIP1K5%1/10W
R11021-216-833-11 METAL CHIP10K5%1/10W
R11031-216-821-11 METAL CHIP1K5%1/10W
R11041-216-845-11 METAL CHIP100K5%1/10W
R11051-216-821-11 METAL CHIP1K5%1/10W
R11061-216-841-11 METAL CHIP47K5%1/10W
R11071-216-809-11 METAL CHIP1005%1/10W
R11081-216-833-11 METAL CHIP10K5%1/10W
R11091-216-847-11 METAL CHIP150K5%1/10W
R11101-216-827-11 METAL CHIP3.3K5%1/10W
R11111-218-867-11 METAL CHIP6.8K0.5%1/10W
R11131-216-835-11 METAL CHIP15K5%1/10W
R11141-216-835-11 METAL CHIP15K5%1/10W
R11151-216-815-11 METAL CHIP3305%1/10W
R11161-216-815-11 METAL CHIP3305%1/10W
R11171-216-835-11 METAL CHIP15K5%1/10W
R11181-216-835-11 METAL CHIP15K5%1/10W
R11191-216-835-11 METAL CHIP15K5%1/10W
R11201-216-846-11 METAL CHIP120K5%1/10W
R11261-216-825-11 METAL CHIP2.2K5%1/10W
R11271-218-867-11 METAL CHIP6.8K0.5%1/10W
R11281-218-867-11 METAL CHIP6.8K0.5%1/10W
R11301-216-827-11 METAL CHIP3.3K5%1/10W
R11311-216-827-11 METAL CHIP3.3K5%1/10W
R11321-216-864-11 SHORT CHIP0
< VARIABLE RESISTOR >
RV1100 1-227-452-11 RES, VAR, CARBON 50K (MIC LEVEL)
RV1101 1-227-452-11 RES, VAR, CARBON 50K (ECHO LEVEL)
JR6001-216-296-11 SHORT CHIP0
JR6031-216-296-11 SHORT CHIP0
R6031-216-841-11 METAL CHIP47K5%1/10W
R6041-216-833-11 METAL CHIP10K5%1/10W
R6051-216-833-11 METAL CHIP10K5%1/10W
R6061-216-841-11 METAL CHIP47K5%1/10W
R6071-216-825-11 METAL CHIP2.2K5%1/10W
R6081-216-845-11 METAL CHIP100K5%1/10W
R6091-216-843-11 METAL CHIP68K5%1/10W
R6101-216-843-11 METAL CHIP68K5%1/10W
R6111-216-839-11 METAL CHIP33K5%1/10W
0R6121-245-605-51 FUSIBLE1005%1/4W
R6131-215-869-11 METAL OXIDE1K5%1W
R6141-215-869-11 METAL OXIDE1K5%1W
R6261-216-842-11 METAL CHIP56K5%1/10W
R6271-216-821-11 METAL CHIP1K5%1/10W
R6281-216-837-11 METAL CHIP22K5%1/10W
R6291-216-830-11 METAL CHIP5.6K5%1/10W
R6301-216-845-11 METAL CHIP100K5%1/10W
R6311-216-845-11 METAL CHIP100K5%1/10W
R6321-216-845-11 METAL CHIP100K5%1/10W
R6331-216-842-11 METAL CHIP56K5%1/10W
R6341-216-825-11 METAL CHIP2.2K5%1/10W
R6351-216-833-11 METAL CHIP10K5%1/10W
R6361-215-891-11 METAL OXIDE6805%2W
R6371-215-891-11 METAL OXIDE6805%2W
R6381-216-845-11 METAL CHIP100K5%1/10W
R6391-216-845-11 METAL CHIP100K5%1/10W
R6401-216-821-11 METAL CHIP1K5%1/10W
R6411-216-821-11 METAL CHIP1K5%1/10W
R6421-216-811-11 METAL CHIP1505%1/10W
R6431-216-811-11 METAL CHIP1505%1/10W
R6441-216-825-11 METAL CHIP2.2K5%1/10W
R6451-216-833-11 METAL CHIP10K5%1/10W
0R6461-260-087-11 CARBON1005%1/2W
R6471-216-821-11 METAL CHIP1K5%1/10W
R6481-216-837-11 METAL CHIP22K5%1/10W
R6491-216-837-11 METAL CHIP22K5%1/10W
R6501-216-821-11 METAL CHIP1K5%1/10W
R6511-216-841-11 METAL CHIP47K5%1/10W
R6521-216-808-11 METAL CHIP825%1/10W
(GNV111D: EXCEPT E2)
R6521-216-814-11 METAL CHIP2705%1/10W
(GNV99D)
R6521-216-815-11 METAL CHIP3305%1/10W
R6531-216-841-11 METAL CHIP47K5%1/10W
R6541-216-841-11 METAL CHIP47K5%1/10W
R6551-216-841-11 METAL CHIP47K5%1/10W
R6561-216-849-11 METAL CHIP220K5%1/10W
R6571-216-849-11 METAL CHIP220K5%1/10W
R6581-216-845-11 METAL CHIP100K5%1/10W
R6601-218-867-11 METAL CHIP6.8K0.5%1/10W
R6611-218-867-11 METAL CHIP6.8K0.5%1/10W
R6621-216-811-11 METAL CHIP1505%1/10W
R6631-216-811-11 METAL CHIP1505%1/10W
0R6681-234-499-21 ENCAPSULATED COMPONENT
R6691-216-821-11 METAL CHIP1K5%1/10W
R6701-216-836-11 METAL CHIP18K5%1/10W
R6711-216-847-11 METAL CHIP150K5%1/10W
R6721-245-711-31 CARBON105%1/2W
R6731-216-842-11 METAL CHIP56K5%1/10W
R6741-216-837-11 METAL CHIP22K5%1/10W
R6761-216-849-11 METAL CHIP220K5%1/10W
R6771-216-849-11 METAL CHIP220K5%1/10W
R6781-216-845-11 METAL CHIP100K5%1/10W
R6801-245-711-31 CARBON105%1/2W
(GNV111D: EXCEPT E2)
R6821-216-821-11 METAL CHIP1K5%1/10W
R6831-216-829-11 METAL CHIP4.7K5%1/10W
R6851-216-833-11 METAL CHIP10K5%1/10W
R6901-245-711-31 CARBON105%1/2W
(GNV99D/GNV111D: E2)
R6901-249-625-31 CARBON105%1/2W
(GNV111D: EXCEPT E2)
R6921-216-841-11 METAL CHIP47K5%1/10W
R6931-216-845-11 METAL CHIP100K5%1/10W
R6941-216-843-11 METAL CHIP68K5%1/10W
R6951-216-845-11 METAL CHIP100K5%1/10W
R6961-216-845-11 METAL CHIP100K5%1/10W
R6971-216-825-11 METAL CHIP2.2K5%1/10W
R6981-216-845-11 METAL CHIP100K5%1/10W
IC9026-805-079-01 IC MB90M407PF-G-145E1
IC9036-600-210-01 IC RPM7240-H8 ( )
IC9046-705-678-01 IC NJM2760V-TE2
< JUMPER RESISTOR/RESISTOR >
JR9091-216-864-11 SHORT CHIP0
JR9101-216-864-11 SHORT CHIP0
JR9111-216-864-11 SHORT CHIP0
JR9121-216-296-11 SHORT CHIP0
JR9131-216-864-11 SHORT CHIP0
JR9141-216-864-11 SHORT CHIP0
JR9151-216-809-11 METAL CHIP1005%1/10W
JR9161-216-864-11 SHORT CHIP0
JR9171-216-864-11 SHORT CHIP0
JR9181-216-864-11 SHORT CHIP0
JR9211-216-296-11 SHORT CHIP0
JR9221-216-296-11 SHORT CHIP0
R9001-216-833-11 METAL CHIP10K5%1/10W
R9011-216-833-11 METAL CHIP10K5%1/10W
R9021-216-833-11 METAL CHIP10K5%1/10W
R9031-216-809-11 METAL CHIP1005%1/10W
R9041-216-809-11 METAL CHIP1005%1/10W
R9051-216-835-11 METAL CHIP15K5%1/10W
R9061-216-835-11 METAL CHIP15K5%1/10W
R9071-216-835-11 METAL CHIP15K5%1/10W
R9081-216-809-11 METAL CHIP1005%1/10W
R9091-216-833-11 METAL CHIP10K5%1/10W
< FERRITE BEAD >
FB9011-216-864-11 SHORT CHIP0
< FLUORESCENT INDICATOR >
FL9011-519-794-21 VACUUM FLUORESCENT DISPLAYS
96
R9101-216-823-11 METAL CHIP1.5K5%1/10W
R9111-216-823-11 METAL CHIP1.5K5%1/10W
R9121-216-809-11 METAL CHIP1005%1/10W
R9141-216-823-11 METAL CHIP1.5K5%1/10W
R9151-216-823-11 METAL CHIP1.5K5%1/10W
R9161-216-823-11 METAL CHIP1.5K5%1/10W
R9171-216-845-11 METAL CHIP100K5%1/10W
R9181-216-845-11 METAL CHIP100K5%1/10W
R9191-216-845-11 METAL CHIP100K5%1/10W
R9201-216-833-11 METAL CHIP10K5%1/10W
R9221-216-857-11 METAL CHIP1M5%1/10W
R9311-216-823-11 METAL CHIP1.5K5%1/10W
R9321-216-823-11 METAL CHIP1.5K5%1/10W
R9331-216-823-11 METAL CHIP1.5K5%1/10W
R9391-216-821-11 METAL CHIP1K5%1/10W
R9401-216-833-11 METAL CHIP10K5%1/10W
R9411-216-809-11 METAL CHIP1005%1/10W
R9421-216-809-11 METAL CHIP1005%1/10W
R9431-216-823-11 METAL CHIP1.5K5%1/10W
R9441-216-805-11 METAL CHIP475%1/10W
R9451-216-839-11 METAL CHIP33K5%1/10W
R9461-216-842-11 METAL CHIP56K5%1/10W
R9471-216-821-11 METAL CHIP1K5%1/10W
R9481-218-867-11 METAL CHIP6.8K0.5%1/10W
R9491-216-821-11 METAL CHIP1K5%1/10W
R9501-216-821-11 METAL CHIP1K5%1/10W
R9511-216-830-11 METAL CHIP5.6K5%1/10W
R9521-216-821-11 METAL CHIP1K5%1/10W
R9531-216-821-11 METAL CHIP1K5%1/10W
R9541-216-833-11 METAL CHIP10K5%1/10W
R9561-216-826-11 METAL CHIP2.7K5%1/10W
R9571-216-823-11 METAL CHIP1.5K5%1/10W
R9581-216-817-11 METAL CHIP4705%1/10W
R9591-216-819-11 METAL CHIP6805%1/10W
R9601-216-821-11 METAL CHIP1K5%1/10W
R9611-216-823-11 METAL CHIP1.5K5%1/10W
R9621-216-823-11 METAL CHIP1.5K5%1/10W
R9631-216-825-11 METAL CHIP2.2K5%1/10W
R9641-216-827-11 METAL CHIP3.3K5%1/10W
R9651-216-829-11 METAL CHIP4.7K5%1/10W
R9661-218-867-11 METAL CHIP6.8K0.5%1/10W
R9671-216-833-11 METAL CHIP10K5%1/10W
R9681-216-835-11 METAL CHIP15K5%1/10W
R9691-216-819-11 METAL CHIP6805%1/10W
R9701-218-867-11 METAL CHIP6.8K0.5%1/10W
R9711-216-821-11 METAL CHIP1K5%1/10W
R9721-216-819-11 METAL CHIP6805%1/10W
R9731-216-819-11 METAL CHIP6805%1/10W
R9741-216-819-11 METAL CHIP6805%1/10W
R9751-216-817-11 METAL CHIP4705%1/10W
R9771-216-821-11 METAL CHIP1K5%1/10W
R9781-216-817-11 METAL CHIP4705%1/10W
R9801-216-821-11 METAL CHIP1K5%1/10W
R9811-216-819-11 METAL CHIP6805%1/10W
R9821-216-819-11 METAL CHIP6805%1/10W
R9831-216-819-11 METAL CHIP6805%1/10W
R9841-216-819-11 METAL CHIP6805%1/10W
R9851-216-819-11 METAL CHIP6805%1/10W
R9861-216-819-11 METAL CHIP6805%1/10W
R9871-216-819-11 METAL CHIP6805%1/10W
R9881-216-819-11 METAL CHIP6805%1/10W
R9891-216-819-11 METAL CHIP6805%1/10W
R9901-216-819-11 METAL CHIP6805%1/10W
R9911-216-819-11 METAL CHIP6805%1/10W
R9921-216-819-11 METAL CHIP6805%1/10W
R9931-216-819-11 METAL CHIP6805%1/10W
R9941-216-819-11 METAL CHIP6805%1/10W
R9951-216-819-11 METAL CHIP6805%1/10W
R9961-216-819-11 METAL CHIP6805%1/10W
R9971-216-819-11 METAL CHIP6805%1/10W
R9991-216-864-11 SHORT CHIP0
R11121-216-823-11 METAL CHIP1.5K5%1/10W
R11351-216-819-11 METAL CHIP6805%1/10W
R11361-216-819-11 METAL CHIP6805%1/10W
R11371-216-819-11 METAL CHIP6805%1/10W
R11411-216-823-11 METAL CHIP1.5K5%1/10W
R11421-216-823-11 METAL CHIP1.5K5%1/10W
R11431-216-823-11 METAL CHIP1.5K5%1/10W
R11471-216-823-11 METAL CHIP1.5K5%1/10W
R11481-216-823-11 METAL CHIP1.5K5%1/10W
R11601-218-867-11 METAL CHIP6.8K0.5%1/10W
R11611-216-833-11 METAL CHIP10K5%1/10W
R11621-218-867-11 METAL CHIP6.8K0.5%1/10W
R11631-216-823-11 METAL CHIP1.5K5%1/10W
R11641-216-825-11 METAL CHIP2.2K5%1/10W
R11651-216-827-11 METAL CHIP3.3K5%1/10W
R11661-216-829-11 METAL CHIP4.7K5%1/10W
R11671-216-814-11 METAL CHIP2705%1/10W
R11681-216-823-11 METAL CHIP1.5K5%1/10W
R11751-216-817-11 METAL CHIP4705%1/10W
R11761-216-819-11 METAL CHIP6805%1/10W
R11771-216-821-11 METAL CHIP1K5%1/10W
R11781-216-823-11 METAL CHIP1.5K5%1/10W
R11791-216-823-11 METAL CHIP1.5K5%1/10W
R11801-216-814-11 METAL CHIP2705%1/10W
R11831-216-808-11 METAL CHIP825%1/10W
R11861-216-829-11 METAL CHIP4.7K5%1/10W
R11871-216-833-11 METAL CHIP10K5%1/10W
R11881-216-821-11 METAL CHIP1K5%1/10W
R11891-216-801-11 METAL CHIP225%1/10W
R11941-216-823-11 METAL CHIP1.5K5%1/10W
R11951-216-823-11 METAL CHIP1.5K5%1/10W
R11961-216-823-11 METAL CHIP1.5K5%1/10W
R11971-216-823-11 METAL CHIP1.5K5%1/10W
R11981-216-823-11 METAL CHIP1.5K5%1/10W
R8001-216-809-11 METAL CHIP1005%1/10W
R8011-216-833-11 METAL CHIP10K5%1/10W
R8021-218-285-11 METAL CHIP755%1/10W
R8031-218-285-11 METAL CHIP755%1/10W
R8041-218-285-11 METAL CHIP755%1/10W
R8051-218-285-11 METAL CHIP755%1/10W
R8061-216-864-11 SHORT CHIP0
R8071-216-809-11 METAL CHIP1005%1/10W
R8081-218-285-11 METAL CHIP755%1/10W
R8091-216-833-11 METAL CHIP10K5%1/10W
R8101-218-285-11 METAL CHIP755%1/10W
R8121-216-857-11 METAL CHIP1M5%1/10W
R8131-216-845-11 METAL CHIP100K5%1/10W
R8141-216-833-11 METAL CHIP10K5%1/10W
M741A-4723-963-A MOTOR ASSY, TABLE
M751A-4737-553-A MOTOR ASSY, LOADING
M8911-763-372-11 FAN, DC
RE7011-477-680-12 ENCODER, ROTARY
< JUMPER RESISTOR >
JR8001-216-864-11 SHORT CHIP0
JR8011-216-864-11 SHORT CHIP0
JR8021-216-864-11 SHORT CHIP0
JR8031-216-864-11 SHORT CHIP0
JR8041-216-864-11 SHORT CHIP0
< COIL >
L8011-414-183-41 INDUCTOR10uH
0T12001-443-585-11 POWER TRANSFORMER
(GNV111D: EXCEPT EA)
0T12001-443-586-11 POWER TRANSFORMER
(GNV99D: E3, E15, PH)
0T12001-443-754-11 POWER TRANSFORMER (GNV111D: EA)
0T12001-443-755-11 POWER TRANSFORMER (GNV99D: EA)
99
Page 100
HCD-GNV99D/GNV111D
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.DateDescription of Revision
1.02005.04New
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.