Sony DWA-F01D Operating Instructions Manual

Wireless Adapter

4-292-344-11 (1)

Operating Instructions

Before operating the unit, please read this manual thoroughly
and retain it for future reference.

DWA-F01D

© 2011 Sony Corporation

Owner’s Record

The model and serial numbers are located at
the side. Record these numbers in the
spaces provided below.
Refer to these numbers whenever you call
upon your Sony dealer regarding this
product.

Model No. DWA-F01D
Serial No.

WARNING

Excessive sound pressure from earphones
and headphones can cause hearing loss.
In order to use this product safely, avoid
prolonged listening at excessive sound
pressure levels.

For the customers in the U.S.A.

This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the
receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.

All interface cables used to connect
peripherals must be shielded in order to
comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC
Rules.

This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.

For the customers in Canada

This Class B digital apparatus complies
with Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies
with the EMC Directive issued by the
Commission of the European Community.

The manufacturer of this product is Sony
Corporation, 1-7-1 Konan, Minato-ku,
Tokyo, Japan.
The Authorized Representative for EMC
and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or
guarantee matters please refer to the
addresses given in separate service or
guarantee documents.

2

Table of Contents

Features ..................................................................................4

Parts Identification ................................................................4

Front/Top/Right Sides .....................................................4

Left Side ...........................................................................6

Using a Battery .......................................................................7

Inserting the Battery ........................................................7

Removing the Battery ......................................................8

Attachment and Connections ................................................8

Attaching the Receiver/Tuner Unit ..................................8

To Connect the Power Cable ...........................................9

To Connect the Audio Cables ..........................................9

On Connecting Word Clock Sync Signal and

Digital Audio Signal ........................................................9

Block Diagram ..................................................................... 10

Troubleshooting ................................................................... 11

Important Notes on Operation ...........................................13

Notes on Using the Adapter ...........................................13

On Cleaning ...................................................................13

Specifications ........................................................................14

Table of Contents

3

Features

56 7

12

The DWA-F01D wireless adapter allows
the optional DWR-S01D digital wireless
receiver or the WRR-855S UHF
synthesizer tuner unit to be rear-mounted on
Sony camcorders. In combination with the
DWR-S01D or WRR-855S, the
DWA-F01D can also work as a portable
wireless receiver.

Wide array of audio output

To draw its full performance, the
DWA-F01D comes equipped with a wide
range of interfaces. One of the analog audio
output connectors can be set to output the
AES/EBU digital format signal. A word
sync input connector is provided for diverse
operational needs.

Monitor output

A monitor output connector is provided to
offer easy monitoring of the audio output.

Parts Identification

Front/Top/Right Sides

123 4

Features / Parts Identification

4

a DC IN (external power input) /

remaining battery indicators

Indicates the power supply status. When
using only a battery power supply, different
colors will indicate the remaining battery
power.

1 Remaining battery indicator

Lights when a battery is inserted.

Green: Ample battery charge remains.
Orange: Battery charge is low.
Red: Battery charge is nearly empty.

e Battery connector

Insert a battery (e.g., NP-F570) here.
The InfoLithium L Series is supported.
If a battery and an external power supply
are connected at the same time, the external
power supply will be used.

When an external power supply is also
connected, this indicator does not light.

2 DC IN (external power input)

indicator

Lights green when an external power
supply is connected.

Note

Even if an external power supply or a
battery is connected, the indicators will not
light if the power switch on the wireless
receiver is turned off.

b OUTPUT 1 connector (XLR)

Outputs balanced analog audio signals.
When a DWR-S01D is installed, you can
select the output tuner in the UTILITY
menu of the DWR-S01D.
Under factory default settings, audio for
TUNER 1 will be output.
When a WRR-855S is installed, audio
signals will be output from this connector
only.

c OUTPUT 2 connector (XLR)

Outputs balanced analog audio signals.
When a DWR-S01D is installed, audio for
TUNER 2 will be output.
When a WRR-855S is installed, this
connector does not function.

d Wireless receiver screw holes

Run in the mounting screws to secure the
receiver/tuner unit.

Note

The DWA-F01D cannot be used to recharge
the battery. Use a commercially available
battery charger to recharge the battery.

For details on inserting the battery, see “Using a
Battery” on page 7.

f Wireless receiver slot

Insert the optional DWR-S01D or
WRR-855S here.

For details on how to attach the receiver or tuner
unit to the DWA-F01D, see “Attaching the Receiver/
Tuner Unit” on page 8.

g DC IN (external power input)

connector (DC jack)

Connects to a 10 V to 17 V DC power
supply.
Use a plug that has an outer diameter of
φ 5.5 mm, an inner diameter of φ 2.1 mm,
and a negative polarity center.

Note

Before beginning operation with an
external power supply, avoid confusing the
polarity of the external battery by checking
the polarity again.

Parts Identification

5