SONY DSC S950 Diagram

SERVICE MANUAL

Ver. 1.0 2009.01

Revision History

Internal memory

ON BOARD

Photo: Silver

DSC-S980

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Korea Model

Link

SPECIFICATIONS

SERVICE NOTE

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

In case of the CCD assy or main board failure, contact your local Sony Service Headquarter for the measures.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DISASSEMBLY REPAIR PARTS LIST

BLOCK DIAGRAM

DSC-S980

Sony EMCS Co.

DIGITAL STILL CAMERA

2009A0500-1

Published by Kohda TEC9-852-650-11

SPECIFICATIONS

Camera

[System]

Image device:

7.79 mm (1/2.3 type) color CCD, Primary color filter

Total pixel number of camera:

Approx. 12.4 Megapixels

Effective pixel number of camera:

Approx. 12.1 Megapixels

Lens: 4× zoom lens f = 5.8 – 23.2 mm (33 –

132mm (35 mm film equivalent)) F2.5 (W) –

5.6 (T)

Exposure control: Automatic exposure, Scene

Selection (7 modes)

White balance: Automatic, Daylight, Cloudy,

Fluorescent 1, 2, 3, Incandescent, Flash

File format (DCF compliant):

Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: AVI (Motion JPEG)

Recording media: Internal Memory (approx.

12 MB), “Memory Stick Duo” media

Flash: Flash range (ISO sensitivity

(Recommended Exposure Index) set to Auto): approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to 11 feet 5 7/8 inches) (W)/approx. 0.5 to 1.5 m (1 feet 7 3/4 inches to 4 feet 11 1/8 inches) (T)

Recording interval of Burst:

Approx. 1.0 seconds

[Input and Output connectors]

(USB)•A/V OUT terminal: Video, Audio (Monaural), USB communication

USB communication:

Hi-Speed USB (USB 2.0 compliant)

[LCD screen]

LCD panel: 6.7 cm (2.7 type) TFT drive Total number of dots: 230 400 (960×240) dots

[Power, general]

Power: Rechargeable battery pack NP-BK1, 3.6 V

AC-LS5K AC Adaptor (sold separately),

4.2 V

Power consumption (during shooting):

1.2 W

Operating temperature: 0 to 40°C (32 to 104°F) Storage temperature: –20 to +60°C (–4 to +140°F) Dimensions: 93.1×55.7×23.8 mm (3 3/4×

2 1/4×15/16 inches) (W/H/D, excluding protrusions)

Mass: Approx. 157 g (5.5 oz) (including NP-BK1

battery pack and strap, etc.)

Microphone: Monaural Speaker: Monaural Exif Print: Compatible PRINT Image Matching III: Compatible PictBridge: Compatible

BC-CSK/BC-CSKA battery charger

Power requirements: AC 100 V to 240 V, 50/

60 Hz, 2.2 W (BC-CSK)/2.3 W (BC-CSKA)

Output voltage: DC 4.2 V, 0.33 A (BC-CSK)/

0.30 A (BC-CSKA) Operating temperature: 0 to 40°C (32 to 104°F) Storage temperature: –20 to +60°C (–4 to +140°F) Dimensions: Approx. 62×24×91 mm (2 1/2×

31/32×3 5/8 inches) (W/H/D)

Mass: Approx. 75 g (2.7 oz) (BC-CSK)/Approx.

70 g (2.5 oz) (BC-CSKA)

Rechargeable battery pack NPBK1

Used battery: Lithium-ion battery Maximum output voltage: DC 4.2 V Mean output voltage: DC 3.6 V Maximum charge voltage: DC 4.2 V Maximum charge current: 1.4 A Capacity: Approx. 3.4 Wh (970 mAh)

Design and specifications are subject to change without notice.

DSC-S980

— 2 —

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.

CAUTION

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

Unleaded solder

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

DSC-S980

— 3 —

1. SERVICE NOTE

1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

Note: When replacing the camera, erase the data in internal memory of the board before replacement.

Method for Copying the Data in Internal Memory

Copy

Copies all images in the internal memory to “Memory Stick Duo” media.

1 Insert “Memory Stick Duo” media having sufficient free capacity. 2 Select [Copy] with v/V on the control button, then press z.

The message “All data on internal memory will be copied” appears.

3 Select [OK] with v, then press z.

Copying starts.

To c a nc e l copying

Select [Cancel] in step 3, then press z.

•Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

•You cannot select images to copy.

•The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory ([Format] in [Internal Memory Tool]).

•A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You cannot choose a specific folder and copy images to it.

•The (Print order) marks on the images are not copied.

Method for Formatting the Internal Memory

This item does not appear when “Memory Stick Duo” media is inserted in the camera.

Format

rmats the internal memory.

•Note that formatting permanently erases all data in the internal memory, including even protected images.

1 Select [Format] with v/V on the control button, then press z.

The message “All data on internal memory will be erased” appears.

2 Select [OK] with v, then press z.

Formatting starts.

To c ancel formatting

Select [Cancel] in step 2, then press z.

DSC-S980

1-1E

The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY

2. DISASSEMBLY

SCREW_TP_1.7_3.7_A0.4_D3_N

MIDDLE BELT (L)

SCREW_TP_1.7_3.7_A0.4_D3_N

MIDDLE BELT (R)

SCREW_TP_1.7_3.7_A0.4_D3_N

CABINET (REAR) ASSY

(To page 2-2)

LCD

SCREW_TP_1.4_3_A_0.2_D=2.5

LCD BRACKET

SCREW_TP_1.4_3_A_0.2_D=2.5

JACK COVER ASSY

SCREW TP 1.4 ∗2.5

CABINET (FRONT) ASSY

BT LID

DSC-S980

2-1

+ 10 hidden pages