The model and serial numbers are located
on the bottom. Record the serial number
in the space provided below. Refer to these
numbers whenever you call your Sony
dealer regarding this product.
Model No. DCRSerial No.
Model No. ACSerial No.
WARNING
To reduce fire or shock hazard, do not
expose the unit to rain or moisture.
Do not expose the batteries to
excessive heat such as sunshine, fire or
the like.
This symbol is intended
to alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying
the appliance.
US
This symbol is intended
to alert the user to the
presence of uninsulated
“dangerous voltage” within
the product’s enclosure
that may be of sufficient
magnitude to constitute
a risk of electric shock to
persons.
US
3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
DANGER - TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the
proper configuration for the power outlet.
US
4
Representative plug of power supply cord of countries/regions around the world.
A Type
(American
Type)
B Type
(British Type)
BF Type
(British Type)
B3 Type
(British Type)
C Type
(CEE Type)
SE Type
(CEE Type)
O Type
(Ocean Type)
The representative supply voltage and plug type are described in this chart.
Depend on an area, Different type of plug and supply voltage are used.
Attention: Power cord meeting demands from each country shall be used.
For only the United States
Use a UL Listed, 1.5-3 m (5-10 ft.), Type SPT-2 or NISPT-2, AWG no. 18 power supply
cord, rated for 125 V 7 A, with a NEMA 1-15P plug rated for 125 V 15 A.”
Before operating the unit, please read this
manual thoroughly, and retain it for future
reference.
CAUTION
Battery pack
If the battery pack is mishandled, the
battery pack can burst, cause a fire or even
chemical burns. Observe the following
cautions.
Do not disassemble.
Do not crush and do not expose the battery
pack to any shock or force such as hammering,
dropping or stepping on it.
Do not short circuit and do not allow metal
objects to come into contact with the battery
terminals.
Do not expose to high temperature above 60°C
(140 °F) such as in direct sunlight or in a car
parked in the sun.
Do not incinerate or dispose of in fire.
Do not handle damaged or leaking lithium ion
batteries.
Be sure to charge the battery pack using a
genuine Sony battery charger or a device that
can charge the battery pack.
Keep the battery pack out of the reach of small
children.
Keep the battery pack dry.
Replace only with the same or equivalent type
recommended by Sony.
Dispose of used battery packs promptly as
described in the instructions.
Replace the battery with the specified type
only. Otherwise, fire or injury may result.
AC Adaptor
Do not use the AC Adaptor placed in a
narrow space, such as between a wall and
furniture.
socket) immediately if any malfunction
occurs while using your camcorder.
Even if your camcorder is turned off, AC
power source (mains) is still supplied to
it while connected to the wall outlet (wall
socket) via the AC Adaptor.
For customers in the U.S.A. and CANADA
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are
recyclable.
You can help preserve our
environment by returning
your used rechargeable
batteries to the collection and
recycling location nearest you.
For more information
regarding recycling of
rechargeable batteries, call toll
free 1-800-822- 8837, or visit
http://www.rbrc.org/
Caution: Do not handle
damaged or leaking LithiumIon batteries.
Battery pack
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
This Class B digital apparatus complies
with Canadian ICES-003.
Use the nearby wall outlet (wall socket)
when using the AC Adaptor. Disconnect
the AC Adaptor from the wall outlet (wall
US
7
8
US
For the customers in the U.S.A.
UL is an internationally recognized safety
organization.
The UL Mark on the product means it has
been UL Listed.
If you have any questions about this
product, you may call:
Sony Customer Information Center 1-800222-SONY (7669).
The number below is for the FCC related
matters only.
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DCR-PJ5
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Declaration of Conformity
Trade Name: SONY
Model No.: DCR-SR21
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Declaration of Conformity
Trade Name: SONY
Model No.: DCR-SX21
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
Note
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
The supplied interface cable must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
To select a MENU item
You can use the multi-selector to select/
decide the items in the MENU.
Select a button by placing an orange
frame over it using /// of the
multi-selector.
Connect your camcorder to the other device with the A/V connecting cable.
.
Output
Signal flow
IN
VIDEO
(Yellow)
Press PROJECTOR.
Sound of other devices cannot be input to the camcorder.
Operation buttons are not displayed on images projected when [PROJECTOR INPUT] is set. If the
camcorder is not connected to another device, a blank blue screen will be projected.
Perform the following operations when you want to project images on the camcorder.
Firstly, press PROJECTOR to stop projecting. Select
[OTHERS] category) [SOURCE] [MEMORY CARD] , and then press
(under
PROJECTOR again.
Turn the power of the camcorder off, then on again, and then press PROJECTOR.
[Show others] [PROJECTOR]
Changing the aspect ratio of the image
You can change the aspect ratio of the image projected by the projector according to the recorded
image size.
Set the input selector of the TV to the input your camcorder will be connected to.
Connect your camcorder to a
1
TV with the A/V connecting
cable (supplied).
Play back movies and photos
2
on your camcorder.
TVs
IN
Signal flow
(VIEW IMAGES)
VCRs
(Red)
AUDIO
(White)
VIDEO
(Yellow)
Notes
For details, refer to the instruction manuals supplied with the TV.
US
24
Saving movies and photos
Saving images on a disc
Connect the AC Adaptor and the power cord (mains lead) to the DC IN jack of your
camcorder and the wall outlet (wall socket).
Using DVDirect Express
Connect the DVD writer to the
1
(USB) jack of your camcorder
with the USB cable of the DVD
writer.
Insert an unused disc into the
2
DVD writer.
Press (DISC BURN) on the
3
DVD writer.
Select [END]
4
[EJECT DISC]
Notes
Refer also to the instruction manual supplied with the DVD writer.
Only unused discs of the following types can be used:
12cm DVD-R/12cm DVD+R
The device does not support two-layered discs.
DVDirect Express is referred to as “DVD writer” in this section.
Do not do any of the following when creating a disc.
Turn off the camcorder
Disconnect the USB cable or the AC Adaptor
Subject the camcorder to mechanical shock or vibration
Eject the memory card from the camcorder
Play the created disc to make sure dubbing was performed correctly before deleting the movies on your
camcorder.
.
Saving movies and photos
US
25
26
US
If [Failed.] or [DISC BURN failed.] appears on the screen, insert another disc into the DVD writer and
perform the DISC BURN operation again.
If the total memory size of movies to be burnt by the DISC BURN operation exceeds that of the disc, disc
creation stops when the limit is reached. The last movie on the disc may be cut off.
Disc creation time to dub movies to the limit of the disc is about 20 minutes to 60 minutes. It may take
more time depending on the recording mode or the number of scenes.
Customizing a disc with DISC BURN OPTION
Perform this operation in the following cases:
When dubbing a desired image
When creating multiple copies of the same disc
When dubbing images in the memory card (DCR-SR21)
Select [DISC BURN OPTION] on the screen in step 3.
elect the recording media containing the movie(s) you want to save (DCR-SR21).
S
elect the movie you want to burn on the disc.
S
Remaining Disc capacity
Select [YES] on the camcorder screen.
fter the operation is completed, select [EXIT] [END].
A
Playing back a disc on the DVD writer
When play back movies on the TV screen, connect the camcorder to a TV.
nsert a created disc into the DVD writer.
I
ress the play button on the DVD writer.
P
elect [END] [EJECT DISC] on the screen and remove the disc after the operation is
S
completed.
If you cannot play back created discs on any DVD player, connect the camcorder to the DVD writer, and
then play back.
Using a DVD writer, etc., other than DVDirect Express
Connect a DVD writer, etc.,
1
to the (USB) jack of your
camcorder with the USB cable
(supplied).
Select the recording media
2
that contains the images on
the camcorder screen.
[ USB CONNECT]: Internal hard disk
(DCR-SR21)
USB CONNECT]: Memory card
[
Record images on the
3
connected device.
Select [END] [YES] after the
4
operation is completed.
Saving movies and photos
Notes
Refer also to the instruction manuals supplied with devices to be connected.
Sony DVD writer may not be available in some countries/regions.
US
27
28
US
Using a recorder, etc.
Insert the recording media
1
into the recording device (a
disc recorder, etc.).
Connect your camcorder to
2
the recording device with
the A/V connecting cable
(supplied).
Start playback on your
3
camcorder, and record it on
the recording device.
Input
VIDEO
(Yellow)
(White)
AUDIO
(Red)
Signal flow
(VIEW IMAGES)
When dubbing is finished,
4
stop the recording device, and
then your camcorder.
Notes
Since dubbing is performed via analog data transfer, the image quality may deteriorate.
You can hide the screen indicators (such as a counter, etc.) on the screen of the monitor device connected.
When you connect a monaural device, connect the yellow plug of the A/V connecting cable to the video
.
input jack, and the white (left channel) or the red (right channel) plug to the audio input jack on the
device.
Saving movies and photos
US
29
30
US
Saving images in external
media (DIRECT COPY)
Connect the AC Adaptor and the power cord (mains lead) to the DC IN jack of your
camcorder and the wall outlet (wall socket).
If the external media has the
1
AC power cable, connect it to
the wall outlet (wall socket).
Connect the external
2
media to the (USB) jack
of your camcorder with the
USB Adaptor Cable (sold
separately).
To the wall outlet (wall
socket)
Select [Copy.].
3
Select after the operation
4
is completed.
Notes
For this operation, you need the USB Adaptor Cable VMC-UAM1 (sold separately).
The USB Adaptor Cable VMC-UAM1 may not be available in some countries/regions.
The number of scenes you can save on the external media are as follows.
Movies: 9,999 movies
Photos: 9,999 frames × 899 folders
The number of scenes may be smaller depending on the type of images recorded.
Loading...
+ 82 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.