Sony BTLS1 User Manual

Since this module is not sold to general end users directly, there is no user manual of
module.
For the details about this module, please refer to the specification sheet of module.

This module should be inst alled in t he host device according to the int er fa c e
specification (installat io n procedure).

2. Regulatory information described in the manual of the end product

2.1. FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, i ncluding interference that may
cause undesired operation.

FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s aut hority to operate the equipme nt .

Note: This equip ment has been tested and found t o comply with the limits for a C lass
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protec tion aga inst harmfu l inter ferenc e in a residential installatio n.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or mor e of t he f ol low i ng measures:

—Reorient or relocate the receiving antenna.
—Increase the separation bet ween the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
—Consult the dealer or an experienced radio/TV tech nic ian for help.

This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.

Confidential

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment has very low levels of RF energy that is deemed to
comply without maximum permissive exposure eval uat ion (MPE).

2.2. IC

This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause interference;
and (2) This device must accept any interference, including interference that may
cause undesired operatio n of t he device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : 1) l’appareil ne doit pas pr oduire de brouillage; 2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.

This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels of RF energy that is deem ed to
comply without maximum permissive exposure eval uat ion (MPE).
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une
énergie RF très faible qui est considérée comme conforme sans évaluation de
l’exposition maximale autorisée (MPE).

3. Labelling

3.1. FCC

FCC ID is printed on BT-LSP1 module as below.

FCC ID: AK8BTLS1
If FCC ID on BT-LSP1 is not visible from outside of the end product, the product sh all
be labelled outside of it as below.
Contains FCC ID: AK8BTLS1

3.2. IC

IC number is printed on BT-LSP1 modu le as be low.

Confidential