Installation and Operation Instructions for the following model:
BRCSDP16
OUTDOOR AND INDOOR DOME HOUSING
CONTENT OF BOX:
(1) Housing
(1) Supplied Parts
(1) Power Connector (Heater/blower)
(1) Toolhead Driver
(1) Operation Instruction Manual
81-IN6584 03082011
ELECTRICAL SPECIFICATIONS
Heater and Blower Only
INSTALLING QUICK RELEASE BRACKET AND
PAN/TILT CAMERA ASSEMBLY (ALL MODELS)
Power 24 VAC, Class 2 Only
!
For BRCSDP16
53 watts at 24 VAC (heater and blower)
30 watts at 24 VAC (camera)
Input Connectors:
BNC
(2) screw-down connectors
RJ-45 Connector
PREPARING PENDANT MOUNT MODEL
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
Slotted Head Screwdriver
1
Carefully remove the housing from the packaging material.
Check to be sure all parts are present.
2 This unit includes a 1½" NPT housing coupling that can
be used with a standard 1½"" NPT pipe. The housing can
be used with other brackets designed with 1½"" male pipe
threads, such as the UNI-WMA1 wall mount bracket.
3 Attach the housing coupling to the bracket or pendant pipe
(Figure 1).
NOTE: Pipe threads should be clean and rust free. Use a
sealer (such as Teflon™ tape or silicone sealer) on
the threads.
1 Using the security tool provided, open the housing by
loosening the (3) captive security screws located on the
housing ring next to the lower clear dome (Figure 2).
Loosen three
Figure 2
security screws
holding dome
2 Install the pan/tilt unit quick-release bracket. It is
recommended that this be done before installing the housing.
On the next page are instructions for mounting the camera
into the housing.
3 It is recommended that the camera be installed at this time.
Connect to the quick-release bracket as shown and
secure per manufacturer directions.
4 Clean the inside of the dome, with the text-wipe provided.
Reattach the housing dome and secure the (3) captive screws.
Do not overtighten the screws. Tighten only to the point at
which the gap between the ring and the housing top closes.
INSTALLING THE HOUSING ASSEMBLY
1 Mount the housing assembly to the mounting bracket and
housing coupling. A safety cable is included with the housing
to temporarily hold it while making wiring connections. Loop
the safety cable over one of the set screws on the housing
coupling and make the appropriate connections using the (2)
screw-down connectors supplied.
Add thread
sealing tape
Figure 1
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding the
!
weight of the entire unit.
2 Undo the safety cable and twist the housing onto the housing
coupling. Secure all (3) setscrews provided on the housing
coupling (Figure 3).
3 Clean the outside of the dome.
Twist and
Secure
Figure 3
WIRING
22
250
120
89
65
44
35
29
25
31
20
400
180
141
90
70
56
47
40
34
18
600
300
225
130
112
90
75
64
55
16
960
480
358
225
179
143
119
102
85
14
-
800
571
350
285
228
190
163
140
12
-
1300
905
525
452
362
301
258
215
10
-
-
1440
830
720
576
480
411
340
5.5
10
20
30
40
50
60
70
80
Total vA
consumed
Wire Gauge
24V AC Wiring Distances
The following are the recommended maximum distances for 24 VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
WIRING INSTRUCTIONS (OUTSIDE OF HOUSING)
BNC
(Large)
Power
(Small)
Alarms
If you wish to provide a single power transformer it is
recommended that:
1. Be certain that you know the total power consumption of
the housing Heater (25 watts) + Blower (1 watt) + camera
pan/tilt (25 watts).
2. Check the supplied wiring chart (see below) to be sure that
you have the proper gauge wire for the distance that you
intend to run your power wires.
3. Bring power to the 3 and 4 position of the power connector
(yellow and green wire).
4. Jumper from the 1st position to the 3rd position and from
the 2nd position to the 4th position of the terminal block.
Be careful not to short between the yellow and green wires.
Wiring Color Code Power and Control Inputs
POWER
1 Camera Power (24 VAC) Red
2 Camera Power (24 VAC) Orange
3 Heater and Blower Power (24 VAC) Yellow
4 Heater and Blower Power (24 VAC) Green
CONTROL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
WIRING INSTRUCTIONS (INSIDE OF HOUSING)
1. The internal power supply provides 12Vdc power.
2. Plug in right angle power plug to back of camera;
plug provides 12Vdc to camera.
AC
24V
Power
Supply
Side
Green
Add 2 jumpers for
single power input
NOTE: The total power consumption for the heater
and blower, PLUS the camera you choose,
need to be added together.
In this example, a 60VA AC24V is required.
Wires from
Dome
Yellow
Orange
Red
+
OPTIONAL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
12DC
Make all connections
to the camera.
–
Maximum distance from transformer to load
INSTALLING THE CAMERA
Install the Sony BRC700 pan/tilt onto the quick release
1
bracket using the (2) screws and washers provided with the
camera (Figure 4).
Figure 4
2 Place the Sony BRC700 pan/tilt and quick release bracket in
the housing, sliding the three open screw slots over the screws
in the housing. Slide the bracket back, then tighten the captive
screw on the bracket (Figures 5 and 6).
Figure 5
Figure 6
!
!
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
1 Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2 Retain Instructions - The safety and operating instructions
should be retained for future reference.
3 Heed Warnings - All warnings on the unit and in the operat-
ing instructions should be adhered to.
4 Follow Instructions - All operating and user instructions
should be followed.
5 Electrical Connections - Only a qualified electrician should
make electrical connections..
6 Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Cable Runs - All cable runs must be within permissible
distance
8 Mounting - This unit must be properly and securely
mounted to a supporting structure capable of sustaining the
weight of the unit. Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the in stalla tion is intact. Failure to comply with the foregoing
could result in the unit separating from the support
structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be damaged if improperly
handled or dropped. If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material. They are the safest
material in which to make future shipments of the equipment.
2 These Installation and Operating Instructions.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with an arrowhead symbol, within
an equilateral triangle, is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SERVICE
If technical support or service is needed, contact Sony at the following
number:
TECHNICAL SUPPORT
8:15AM to 7:30PM (Eastern Time)
1-800-883-6817
Note:
Please note that to achieve the increased depth with the aspheric design for optimal camera lens to
capsule orientation, the capsule is slightly angled around the highest section. This creates a ”line’, visible to
the naked eye, around the upper most section of the capsule. This “line” serves as the geometric center line
used to insure proper camera placement. It is not typically seen by the camera. However, Sony RZ series
PTZ cameras are able to tilt up above the horizon to 25°, this wide range of tilt motion at a wide angle view
may cause this line to be captured in the image.
Warranty
For warranty information on this and other Sony Security Systems Products, please visit:
http://pro.sony.com/bbsccms/services/files/servicesprograms/SecurityWarranty.pdf
Loading...