Outdoor and Indoor Dome Housings
Installation and Operation Instructions for the following models:
BRCSDP12
(1) Housing
(1) Supplied Parts
(1) Power connector (Heather/blower)
(1) Toolhead driver
(1) Operation Instruction Manual
Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656
www.sony.com/security
ELECTRICAL SPECIFICATIONS
Heater and Blower Only
Power 24 VAC, Class 2 Only
!
For BRCSDP12
53 watts at 24 VAC (heater and blower)
Input Connectors:
BNC
(2) screw-down connectors
RJ-45 Connector
INSTALLING QUICK RELEASE BRACKET AND
PAN/TILT CAMERA ASSEMBLY (ALL MODELS)
1 Using the security tool provided, open the housing by loosen-
ing the (3) captive security screws located on the housing ring
next to the lower clear dome (Figure 2).
Camera Power
Refer to the camera's installation guide.
PREPARING PENDANT MOUNT MODEL
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
Carefully remove the housing from the packaging material.
1
Check to be sure all parts are present.
2 This unit includes a 1 1/2" NPT housing coupling that can
be used with a standard 1 1/2" NPT pipe. The housing can
be used with other brackets designed with 1 1/2" male pipe
threads, such as the SNCWM20 wall mount bracket.
3 Attach the housing coupling to the bracket or pendant pipe
(Figure 1).
NOTE: Pipe threads should be clean and rust free. Use a
sealer (such as Tefl on™ tape or silicone sealer) on
the threads.
Loosen three
security screws
holding dome
Figure 2
2 Install the pan/tilt unit quick-release bracket. It is recom-
mended that this be done before installing the housing.
On the next page are instructions for mounting quick-release
brackets from selected manufacturers.
3 It is recommended that the pan/tilt be installed at this time.
Connect to the quick-release bracket as shown and
secure per manufacturer directions.
4 Clean the inside of the dome, with the text-wipe provided.
Reattach the housing dome and secure the (3) captive screws.
Do not overtighten the screws. Tighten only to the point at
which the gap between the ring and the housing top closes.
INSTALLING THE HOUSING ASSEMBLY
1 Mount the housing assembly to the mounting bracket and
housing coupling. A safety cable is included with the housing
to temporarily hold it while making wiring connections. Loop
the safety cable over one of the set screws on the housing
coupling and make the appropriate connections using the (2)
screw-down connectors supplied.
Figure 1
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding the
!
weight of the entire unit.
© 2003 by Sony Corporation
Add thread
sealing tape
2 Undo the safety cable and twist the housing onto the housing
coupling. Secure all (3) setscrews provided on the housing
coupling (Figure 3).
3 Clean the outside of the dome.
Twist and
Secure
Figure 3
1
10/13/04
WIRING
CHART A WIRING COLOR CODE
POWER AND CONTROL INPUTS
POWER
1 Camera Power (12 VDC) Red
2 Camera Power (12 VDC) Orange
3 Heater & Blower Power (24 VAC) Yellow
4 Heater & Blower Power (24 VAC) Green
NOTE: Failure to provide power to heater and blower will
void the warranties on both the housing and camera.
OPTIONAL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
INSTALLING THE CAMERA
Install the Sony BRC300 pan/tilt onto the quick release
1
bracket using the (4) screws provided with the camera
(Figure 4).
Figure 4
CHART B POWER AND CONTROL OUTPUTS
CAMERA POWER
1 Camera Power (12 VDC) Red
2 Camera Power (12 VDC) Orange
Connect the power plug to the camera per Sony SNCRZ30N
instructions.
OPTIONAL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
24k VAC Wiring Distances
The following are the recommended maximum distances for 24 VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
Wire Gauge
Total vA
consumed
50
20 18 16 14 12 10
22
56 90 143 228 362 576
35
2 Place the Sony BRC300 pan/tilt and quick release bracket
in the housing, sliding the three open screw slots over the
screws in the housing. Slide the bracket forward, then tighten
the captive screw on the bracket (Figures 5, 6, and 7).
Figure 5
© 2003 by Sony Corporation
2
Figure 6
Figure 7
10/13/04
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
1 Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2 Retain Instructions - The safety and operating instructions
should be retained for future reference.
3 Heed Warnings - All warnings on the unit and in the operat-
ing instructions should be adhered to.
4 Follow Instructions - All operating and user instructions
should be followed.
5 Electrical Connections - Only a qualifi ed electrician should
make electrical connections..
6 Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Cable Runs - All cable runs must be within permissible
distance
8 Mounting - This unit must be properly and securely
mounted to a supporting structure capable of sustaining the
weight of the unit. Accordingly:
a. The installation should be made by a qualifi ed installer.
b. The installation should be in compliance with local
codes.
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the in stalla tion is intact. Failure to comply with the foregoing
could result in the unit separating from the support
structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
!
UNPACKING
Unpack carefully. Electronic components can be damaged if improperly
handled or dropped. If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material. They are the safest
material in which to make future shipments of the equipment.
2 These Installation and Operating Instructions.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning fl ash with an arrowhead symbol, within
an equilateral triangle, is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of suffi cient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
SERVICE
If technical support or service is needed, contact Sony at the following
number:
TECHNICAL SUPPORT
8:15AM to 7:30PM (Eastern Time)
1-800-883-6817
© 2003 by Sony Corporation
5
10/13/04
Loading...