Sony BKSI-2440 Series, BKSI-2040 Series, BKSI-2440, BKSI-2043, BKSI-2044 Installation Manual
...
iDC CPU BOARD
BKSI-2440
iDC LINK INTERFACE BOARD
BKSI-2441
IDC SERIAL I/F CONNECTOR BOARD
BKSI-2042
IDC PARALLEL I/F CONNECTOR BOARD
BKSI-2043
IDC S-BUS I/F CONNECTOR BOARD
BKSI-2044
INSTALLATION MANUAL
2nd Edition (Revised 1)
Serial No. 10112 and Higher: BKSI-2440
Serial No. 10026 and Higher: BKSI-2441
Serial No. 10490 and Higher: BKSI-2042
Serial No. 10589 and Higher: BKSI-2043
Serial No. 10730 and Higher: BKSI-2044
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
BKSI-2440
PRECAUTION
Do not install with turning the power on
Touching the power contact portion or the primary
winding circuit may cause electric shock. Turn off the
power and unplug the appliance from the outlet before
installing.
When disconnecting a connector, be careful about
the edges on the connector panel
Disconnecting a connector with excessive force may
cause an injury of your fingers from the edges on the
connector panel.
Hold a harness of a connector firmly, and disconnect it
softly.
BKSI-2440
1 (P)
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manual .................................................................................................... 3 (E)
Contents ............................................................................................................... 4 (E)
Trademarks .......................................................................................................... 4 (E)
1. Installation
1-1. Overview ...............................................................................................1-1 (E)
1-2. Installation of the Board ........................................................................ 1-3 (E)
1-2-1. Plug-in Board Installation .................................................... 1-3 (E)
1-2-2. Connector Panel Installation ................................................ 1-4 (E)
1-3. Connection ............................................................................................ 1-6 (E)
1-3-1. Connection between SMS Gateway and SIU-80A/80 ......... 1-6 (E)
1-3-2. Connection of iDC Link ....................................................... 1-6 (E)
1-4. Information of BKSI-2440 ....................................................................1-8 (E)
1-4-1. Setting and Function of Switches/LEDs on Board .............. 1-8 (E)
1-5. Information of BKSI-2441 ..................................................................1-10 (E)
1-5-1. Location and Function of Connectors ................................1-10 (E)
1-5-2. Connecting Connector and Cables .....................................1-10 (E)
1-5-3. Signal Inputs/Outputs .........................................................1-11 (E)
1-5-4. Switch Setting ....................................................................1-11 (E)
1-6. Information of BKSI-2042 ..................................................................1-12 (E)
1-6-1. Location and Function of Connectors ................................1-12 (E)
1-6-2. Connecting Connector ........................................................ 1-12 (E)
1-6-3. Signal Inputs/Outputs .........................................................1-13 (E)
1-6-4. Switch Setting ....................................................................1-13 (E)
1-6-5. Connection of the RS-232C/422A Connectors ..................1-14 (E)
1-7. Information of BKSI-2043 ..................................................................1-15 (E)
1-7-1. Location and Function of Connectors ................................1-15 (E)
1-7-2. Connecting Connector ........................................................ 1-15 (E)
1-7-3. Signal Inputs/Outputs .........................................................1-15 (E)
1-8. Information of BKSI-2044 ..................................................................1-16 (E)
1-8-1. Location and Function of Connectors ................................1-16 (E)
1-8-2. Connecting Connector and Cable .......................................1-16 (E)
1-8-3. S-BUS/VS-BUS Connection Examples .............................1-17 (E)
1-9. Specifications ...................................................................................... 1-18 (E)
BKSI-2440
1 (E)
Purpose of this manual
Related manual
Manual Structure
This manual is Installation Manual of the Intelligent Device Controller (iDC)
boards BKSI-2040 series and BKSI-2440 series.
This manual is intended for use by trained system and service engineers, and
describes the information when installing the following boards.
BKSI-2440 series
. BKSI-2440 iDC CPU Board
. BKSI-2441 iDC Link Interface Board
BKSI-2040 series
. BKSI-2042 IDC Serial I/F Connector Board
. BKSI-2043 IDC Parallel I/F Connector Board
. BKSI-2044 IDC S-BUS I/F Connector Board
The following manual is prepared for this series.
..
. BKSI-2440 Maintenance Manual (Available on request)
..
This manual describes the general service information and detailed information
with the intention of servicing based on the component parts of BKSI-2440 series.
For obtaining, contact to your local Sony Sales Office/Service Center.
Part number: 9-968-014-0X
BKSI-2440
3 (E)
Contents
This manual is organized by following sections.
1-1. Overview
This section describes the overview of BKSI-2440 series.
1-2. Installation of the Board
This section describes the installation of the boards to System Interface Unit SIU80A/80.
1-3. Connection
This section describes the connections between gateway and System Interface Unit
SIU-80A/80, and between two or more SIU-80A/80s.
1-4. Information of BKSI-2440
This section describes the information for BKSI-2440.
1-5. Information of BKSI-2441
This section describes the information for BKSI-2441.
1-6. Information of BKSI-2042
This section describes the information for BKSI-2042.
Trademarks
1-7. Information of BKSI-2043
This section describes the information for BKSI-2043.
1-8. Information of BKSI-2044
This section describes the information for BKSI-2044.
1-9. Specifications
This section describes the specifications of BKSI-2040 series and BKSI-2440 series.
Trademarks and registered trademarks used in this manual are follows.
. Ethernet is a registered trademark of Xerox Corporation.
. PC/AT is a registered trademark of International Business Machine, Inc.
4 (E)
BKSI-2440
Section 1
Installation
1-1. Overview
Intelligent Device Controller (iDC) boards BKSI-2040 series (BKSI-2042/2043/2044) and BKSI-2440
series (BKSI-2440/2441) are installed in System Interface Unit SIU-80A/80, so as to control the devices
(Network Storage System, VTR, Routing Switcher, etc.) which are used in Server Management System
(SMS).
. The required power for operation of each board is supplied from System Interface Unit SIU-80A/80.
. The model label (1 set) is supplied with each board.
BKSI-2440 : iDC CPU BOARD (CPU-356 BOARD)
This is the main CPU board, and is used for the following two purposes.
1. For root controller
Transmits the application commands sent through the SMS gateway to the iDC boards
controlled each device.
Multiple iDC boards controlling each device can be controlled by only one this board that is installed
in each Server Management System (SMS).
(The number of iDC boards which can be controlled by one this board depends on the installing
application software.)
*: Hereinafter, BKSI-2440/2441/2042/2043/2044 is described as iDC board.
2. For device controller
Each device of the SMS can be controlled when this board is used as a pair with each board BKSI2042, BKSI-2043 or BKSI-2044.
BKSI-2441 : iDC LINK INTERFACE BOARD (IF-905 BOARD)
This connector panel carrys out the interface with SMS gateway, or the interface between iDC boards.
BKSI-2042 : IDC SERIAL I/F CONNECTOR BOARD (IO-111 BOARD)
This connector panel is used for the RS-232C/422A interface.
Use this panel a pair with device controller BKSI-2440.
For details, refer to the Installation Manual for BKSI-2040.
BKSI-2043 : IDC PARALLEL I/F CONNECTOR BOARD (IO-109 BOARD)
This connector panel is used for the interface of the input and output signals at
the parallel contacts.
Use this panel a pair with device controller BKSI-2440.
For details, refer to the Installation Manual for BKSI-2040.
*
which are
BKSI-2044 : IDC S-BUS I/F CONNECTOR BOARD (IO-110 BOARD)
This connector panel is used for the S-BUS/VS-BUS interface.
Use this panel a pair with device controller BKSI-2440.
For details, refer to the Installation Manual for BKSI-2040.
n
To control the devices with the boards described above, the optional software (Server Management
Software BSS-1) is required.
Refer to the Installation manual supplied with the software for the installation procedures.
BKSI-2440
1-1 (E)
Loading...