Sony BDP-S300, BDP-S301 User Manual

3-214-290-11(1)
©2007 Sony Corporation
B l u - r a y D i s c P l a y e r
B D P - S 3 0 0 B D P - S 3 0 1
O p e r a t i n g I n s t r u c t i o n s

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. The AC power cord must be changed only at a qualified service shop.
CAUTION
The use of optical instruments with this product will increase eye hazard. As the laser beam used in this Blu-ray Disc player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.
This label is located on the laser protective housing inside the enclosure.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee th at interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
For customers in the U.S.A
If this product is not working properly, please call 1­800-222-7669.
Owner’s Record
The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. BDP-S300
Serial No.______________
For Customers in Canada
If this product is not working properly, please call 1­877-602-2008 for Peace of Mind Warranty
Replacement service.
For other product related questions please contact our Customer Information Service Center at 1-877-899-7669 or write to us at: Customer Information Service 115 Gordon Baker Road, Toronto, Ontario, M2H 3R6
BDP-S301

Notes About the Discs

• To keep the disc clean, handle the disc by its edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth. Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner, commercially available disc/ lens cleaners, or anti-static spray intended for vinyl LPs.
• If you have printed the disc’s label, dry the label before playing.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
of electric shock to persons.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
sufficient magnitude to constitute a risk
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2

Important Safety Instructions

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Precautions

On safety
• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
• Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.
On power sources
• The player is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the player itself has been turned off.
• If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.
On placement
• Place the player in a location with adequate ventilation to prevent heat build-up in the player.
• Do not place the player on a soft surface such as a rug.
• Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.
• Do not install the player in an inclined position. It is designed to be operated in a horizontal position only.
• Keep the player and the discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers.
• Do not place heavy objects on the player.
• Do not install this player in a confined space, such as a bookshelf or similar unit.
• Install this player so that the power cord can be unplugged from the wall socket immediately in the event of trouble.
• Do not expose the battery to excessive heat such as direct sunlight, fire or the like.
On operation
• If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.
• When you move the player, take out any discs. If you don’t, the disc may be damaged.
On adjusting volume
Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Moreover, wipe the glass part on the front panel with a soft, dry cloth. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
On cleaning discs, disc/lens cleaners
Do not use a commercially available cleaning disc or disc/lens cleaner (wet or spray type). These may cause the apparatus to malfunction.
On replacement of parts
In the events that this player is repaired, repaired parts may be collected for reuse or recycling purposes.
IMPORTANT NOTICE
Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panel televisions and projection televisions are susceptible to this.
3

Table of Contents

Adjusting the Pictures ......................................28
Fine-tuning the picture to your preference .........28
Locking a Disc ....................................................29
Setting/changing the password ..........................29
Setting the Parental Control for DVD VIDEOs ...30
Setting the Parental Control for BD-ROMs ........30
WARNING ...............................................................2
Notes About the Discs ........................................2
Important Safety Instructions ...........................3
Precautions ...........................................................3
Table of Contents .................................................4
About this manual ................................................5
This Player Can Play the Following
Discs and Files
Examples of discs that the player cannot play .....6
About playback of discs recorded in AVCHD
format .............................................................6
BD/DVD region code ...........................................7
Note on playback operations of BDs/DVDs .........7
Copyrights ............................................................7
................................................5
Main Features .......................................................7
Getting Started
Step 1: Unpacking ...............................................9
Step 2: Connecting the Video Cords/HDMI
Cord
.................................................................10
A Connecting to a video input jack ...................10
B Connecting to an S VIDEO input jack ...........10
C Connecting to component video input jacks
(Y, PB, PR) ....................................................10
D Connecting to an HDMI input jack ................11
About the ‘BRAVIA’ Theatre Sync features
(for HDMI connections only) .........................11
Step 3: Connecting the Audio Cords ............12
A
Connecting to your TV ..............................13
B
Connecting to a stereo amplifier (receiver)
and 2 speakers .............................................13
C
Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro Logic)
decoder and 3 to 6 speakers ........................14
D-1
Connecting to an AV amplifier (receiver)
with 5.1ch input jacks and 6 speakers .........14
D-2
Connecting to an AV amplifier (receiver)
with a digital input jack and 6 speakers ........15
D-3
Connecting to an AV amplifier (receiver)
with an HDMI input jack and 8 speakers ......15
Step 4: Connecting the Power Cord .............16
Step 5: Preparing the Remote ........................16
If you want to control your TV with the supplied
remote ..........................................................17
Step 6: Easy Setup ............................................18
Step 7: Additional Adjustments .....................19
Basic Operations
Playing a Disc .....................................................20
Guide to Displays ...............................................22
Entering characters ............................................23
Guide to the Remote .........................................24
Playing in various play mode .............................25
Searching using the remote ...............................26
Checking the Disc Information .......................26
Clarifying Low Volume Sounds
(Audio DRC)
...................................................27
Watching Movie Files
Viewing All Titles ...............................................32
Playing a title .....................................................33
Browsing by Genre, Quicklist, or Folder .....34
Searching for a Title ..........................................34
Programming Playback (Quicklist) ...............35
Listening to Music Files
Viewing All Artists .............................................36
Playing a track ...................................................37
Browsing by Artist, Album, Genre,
Quicklist, or Folder
......................................38
Searching for a Track .......................................38
Programming Playback (Quicklist) ...............39
Viewing Photo Files
Viewing All Folders ...........................................40
Playing a slideshow ...........................................41
Browsing by Date, Quicklist, or Folder ........42
Searching for a Photo .......................................42
Programming a Slideshow Playback
(Quicklist)
.......................................................43
Changing the Initial Settings
Using the Setup Displays ................................44
Video Setup .........................................................45
Audio Setup .........................................................47
Language .............................................................49
Parental Control .................................................50
Speakers ...............................................................51
Options .................................................................52
Resetting the Player ..........................................53
Additional Information
Troubleshooting .................................................54
Self-Diagnosis Function ...................................57
Index to Parts and Controls ............................58
Front panel .........................................................58
Front panel display ............................................59
Rear panel .........................................................59
GNU License Information ................................60
Glossary ...............................................................66
Specifications .....................................................67
Language Code List ..........................................68
Parental Control Country/Area Code List ...69
Index ......................................................................70
4

About this manual

Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they have the same or similar names as those on the remote. The meanings of the icons used in this manual are described below:
Icon Meaning
BD
DVD
DATA DVD
CD
* MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO
(International Organization for Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.
Note
The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen.
Functions available for BD-ROMs including DL discs.
Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR mode or DVD-RWs/DVD-Rs in video mode, including 8 cm discs.
Functions available for DATA DVDs (DVD+RWs/DVD+Rs/DVD-RWs/DVD­Rs containing MPEG-2 PS movie files, MP3* audio tracks, and JPEG image files).
Functions available for music CDs or CD­Rs/CD-RWs in music CD Format.

This Player Can Play the Following Discs and Files

Disc Format
Blu-ray Disc
DVD VIDEO
DVD-RW/-R
DVD+RW/+R
CD
“Blu-ray Disc” is a trademark. “Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD­R,” “DVD VIDEO,” and “CD” logos are trademarks.
Supported file formats (DATA DVD only)
DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs are called “DATA DVD” in this manual when the discs contain playable files. The following file formats are supported:
• MPEG-2 PS movie files.
• MP3 music files.
• JPEG* image files.
* JPEG format conforming to UDF (Universal Disk Format).
Notes about BD-ROM compatibility
This player supports BD-ROM Profile 1 only. Playback of later versions and BDs other than BD-ROM is not guaranteed. Since the Blu-ray Disc specifications are new and evolving, some discs may not play depending on the disc type and the version. The audio output differs depending on the source, connected output jack, and selected audio settings. For details, see page 48.
,continued
5
Examples of discs that the player
About playback of discs recorded in
cannot play
The player cannot play the following discs:
• BD-REs/BD-Rs.
• BDs with cartridge.
• DVD-RWs/DVD-Rs of VR mode.
• DVD-RAMs.
• HD DVDs.
• DVD Audio discs.
• DATA CDs (CD-Rs/CD-RWs other than music CD format).
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
• VCDs/Super VCDs.
• HD layer on Super Audio CDs.
Also, the player cannot play the following discs:
• A BD-ROM/DVD VIDEO with a different region code.
• A disc recorded in a color system other than NTSC, such as PAL (this player conforms to the NTSC color system).
• A disc that has a non-standard shape (e.g., card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane tape or a sticker still left on it.
Notes
• Notes about DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/ CD-RWs
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/ CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The DVD disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback.
• Music discs encoded with copyright protection technologies
This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.
• Note on DualDiscs
A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.
• Note about double-layer DVDs
The playback pictures and sound may be momentarily interrupted when the layers switch.
AVCHD format
This player can play AVCHD format discs.
TM
What is the AVCHD format?
The AVCHD format is a high definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification*1 or the 720p specification* coding technology. The MPEG-4 AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM system is used to compress audio data. The MPEG-4 AVC/ H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. The MPEG-4 AVC/H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVD discs, in the same way as it would be for a standard definition (SD) television signal.
“AVCHD” and the AVCHD logo are trademarks of Matsushita Electric Industrial Co., Ltd. and Sony Corporation.
1
*
A high definition specification which utilizes 1080 effective scanning lines and the interlace system.
2
A high definition specification which utilizes 720 effective scanning
*
lines and the progressive system.
Notes
• Some AVCHD format discs may not play, depending on the recording condition.
• The AVCHD format disc will not play if it has not been correctly finalized.
2
on DVDs, using efficient data compression
6

BD/DVD region code

Your player has a region code printed on the back of the unit and only will play BD-ROM/DVD VIDEOs (playback only) labeled with identical region codes. This system is used to protect copyrights.

Main Features

DVD VIDEOs labeled will also play on this player.
ALL
Depending on the BD-ROM/DVD VIDEO, there may be no region code indication, even though playing the BD-ROM/DVD VIDEO is prohibited by area restrictions.
1
COMPONENT
VIDEO OUT
VIDEO
OUT
Y
AC IN
1
HDMI OUT
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
B
P
P
R
S VIDEO
5.1CH OUTPUT
AUDIO
OUT
FRONT REAR CENTER
L
L
R
R
WOOFER

Note on playback operations of BDs/ DVDs

Some playback operations of BDs/DVDs may be intentionally set by software producers. Since this player plays BDs/DVDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the BDs/DVDs.

Copyrights

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Experience the high definition (HD) quality audio/video output and the library function of this Blu-ray Disc Player.
BD-ROM playback
BD-ROM is a next generation optical disc format in the HD era. Featuring massive storage capacity of 25 to 50 GB (five times larger than a DVD) and a high-speed transfer rate of up to 54 Mbps, the format offers not only uncompromised HD quality
1*2
video*
, but also enables rich bonus content on a single disc
and HD quality audio up to 8ch, and interactive operability.
*1A compatible HD display device is necessary to enjoy the same
quality.
2
Some discs allow viewing only with an HDMI connection.
*
24p True Cinema
Movies shot with a film camera consist of 24 frames per second. Since conventional televisions (both CRT and flat panels) display frames either at 1/60 or 1/50 second intervals, the 24 frames do not appear at an even pace. When connected to a TV with 24p capabilities, the player displays each frame at 1/24 second intervals — the same interval originally shot with the film camera, thus faithfully reproducing the original cinema image.
HDMI Control (‘BRAVIA’ Theatre Sync)
‘BRAVIA’ Theatre Sync Function makes operations simple by connecting Sony components that are compatible with the HDMI Control function with an HDMI cord.
BD-J application
The BD-ROM format supports Java for interactive functions. “BD-J” offers content providers almost unlimited functionality when creating interactive BD-ROM titles*.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Esmertec and Jbed are trademarks or registered trademarks of Esmertec AG. © 2000-2007 Esmertec AG
* This player does not support downloadable BD-J content.
Support of uncompressed multi-channel Linear PCM
In combination with a compatible AV amplifier, the player can output up to 8ch Linear PCM surround sound*. With a non­compatible amplifier, the player can output 5.1ch analog signals from its 5.1CH OUTPUT jack for high quality audio enjoyment.
* Note that the DIGITAL OUT (COAXIAL or OPTICAL) jack does not
output 8ch signals. You will need an HDMI cord and an HDMI­compatible device that support 8ch signals.
AVCHD format disc playback
The player supports AVCHD format files–high definition recordings made on AVCHD-compatible camcorders. Your high definition personal archive is readily playable in HD quality.
,continued
7
HDMI (High-Definition Multimedia Interface) digital interface
When connected to an HDMI-equipped display device using a single HDMI cord, the player can output both SD to HD video and multi-channel audio signals, in digital form without degradation. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals.
Library function for recorded files (For JPEG image, MP3 audio, MPEG-2 PS movie files only)
With DATA DVDs created on other DVD devices, three separate movie/music/photo Title List-browsers allow for easy sorting, searching and playback including a slideshow.
8

Step 1: Unpacking

Getting Started

Follow steps 1 to 7 to hook up and adjust the settings of the player. For jack and button names, see “Index to Parts and Controls(page 58).
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this player to a TV that does not have a video input jack.
• Be sure to disconnect the power cord of each component before connecting.
• Do not apply too much pressure on the connecting cords. Pushing against the cabinet wall, etc., may damage the cord.
Check that you have the following items:
• Video cord (phono plug × 1) (1)
• Stereo audio cord (phono plug × 2) (1)
• HDMI cord (1) (supplied with BDP-S301 only)
• Power cord (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
Getting Started
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . 9
Step 2: Connecting the Video Cords/
HDMI Cord . . . . . . . . . . . . . . . . . . . . . . . . .10
Step 3: Connecting the Audio Cords . . . . . . . .12
Step 4: Connecting the Power Cord . . . . . . . . .16
Step 5: Preparing the Remote . . . . . . . . . . . . .16
Step 6: Easy Setup. . . . . . . . . . . . . . . . . . . . . .18
Step 7: Additional Adjustments . . . . . . . . . . . .19
9

Step 2: Connecting the Video Cords/HDMI Cord

Connect this player to your TV monitor, projector or AV amplifier (receiver) using a video cord. Select one of the patterns A through D, according to the input jack on your TV monitor, projector or AV amplifier (receiver). In order to view 1080p progressive signals with a compatible TV, projector, or monitor with an HDMI input jack, you must select pattern D. You can use pattern C to view 480p/720p progressive signals or 1080i interlace signals on a compatible device with component video input jacks.

A Connecting to a video input jack

Connect the supplied video cord (yellow) to the yellow (video) jack. You will enjoy standard quality images.
Blu-ray Disc player
COMPONENT
VIDEO OUT
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
B
P
R
S VIDEO
VIDEO
OUT
VIDEO
AC IN
HDMI OUT
to VIDEO OUT
(yellow)
S VIDEO
(yellow)
Video cord (supplied)
: Signal flow
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see page 45.
Note
Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR, you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack, connect the player to this jack.
5.1CH OUTPUT
AUDIO
OUT
FRONT REAR CENTER
L
L
R
R
WOOFER
INPUT
VIDEO
L
AUDIO
R
TV, projector, or AV amplifier (receiver)

B Connecting to an S VIDEO input jack

Connect using an S VIDEO cord (not supplied). You will enjoy high quality images.
Blu-ray Disc player
COMPONENT
VIDEO OUT
AC IN
VIDEO
OUT
VIDEO
S VIDEO
: Signal flow
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
HDMI OUT
B
P
R
S VIDEO
to S VIDEO
S VIDEO cord (not supplied)
5.1CH OUTPUT
AUDIO
OUT
FRONT REAR CENTER
L
L
R
R
WOOFER
INPUT
S VIDEO
TV, projector, or AV amplifier (receiver)
C Connecting to component video input jacks (Y, P
Connect the component via the COMPONENT VIDEO OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images. You can also enjoy higher quality pictures from 480p/720p progressive signals or 1080i interlace signals, if your TV, projector or AV amplifier (receiver) is compatible.
AC IN
COMPONENT
VIDEO OUT
Y
B
P
P
R
(green)
(blue)
(red)
: Signal flow
B, PR)
COMPONENT
VIDEO OUT
VIDEO
OUT
Y
VIDEO
P
HDMI OUT
B
P
R
S VIDEO
to COMPONENT VIDEO OUT
Component video cord (not supplied)
Blu-ray Disc player
5.1CH OUTPUT
AUDIO
OUT
L
R
FRONT REAR CENTER
L
R
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
(green)
(blue)
(red)
TV, projector, or AV amplifier (receiver)
WOOFER
COMPONENT
VIDEO IN
Y
PB
PR
10
Blu-ray Disc player
VCR
TV Connect directly

D Connecting to an HDMI input jack

Use an HDMI cord to enjoy high quality digital pictures and sound through the HDMI OUT jack. You will enjoy higher quality pictures from 480p/1080i, or 1080p (highest among the player output), if your TV, projector or AV amplifier (receiver) is compatible.
Blu-ray Disc player
COMPONENT
VIDEO OUT
HDMI
OUT
AC IN
HDMI OUT
to HDMI OUT
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
B
P
R
S VIDEO
L
R
AUDIO
OUT
5.1CH OUTPUT
FRONT REAR CENTER
L
R
WOOFER
About indicators for HDMI connection
After the player is turned on, the HD indicator on the front panel lights up when outputting 720p/1080i/1080p video signals. The HDMI indicator lights up when an HDMI device is connected.
Notes
• Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In the case of 480/720/1080 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 480p/720p/1080p Blu-ray Disc player, please contact our customer service center.
• If the picture is not clear, natural, or to your satisfaction, change the video output resolution by pressing VIDEO FORMAT (page 46).
• Be sure to use only an HDMI cord that bears the HDMI logo.
Getting Started
HDMI cord (supplied with BDP-S301 only)
TV, projector, or AV amplifier (receiver)
HDMI IN
This Blu-ray Disc player incorporates High-Definition Multimedia Interface (HDMI™) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Notes on connecting to the HDMI OUT jack
Observe the following as improper handling may damage the HDMI OUT jack and the connector.
• Carefully align the HDMI OUT jack on the back of the player and the HDMI connector by checking their shapes. Make sure the connector is not upside down or tilted.
HDMI
UT
O
I
HDM
OUT

About the ‘BRAVIA’ Theatre Sync features (for HDMI connections only)

By connecting Sony components that are compatible with the HDMI Control function with an HDMI cord, operation is simplified as below:
• One-Touch Play (page 21) You can turn on the player and TV/AV receiver, set the TV/AV receiver’s input to the player, and start playback with one touch of the H button.
• System Power-Off When you turn the TV off by using the POWER button on the TV’s remote, the HDMI compatible components turn off automatically.
To prepare for the ‘BRAVIA’ Theatre Sync features
Set “HDMI Control” of “Options” setup to “On” (page 52).
Note
Depending on the connected component, the HDMI Control function may not work. Refer to the operating instructions supplied with the component.
• Be sure to disconnect the HDMI cord when moving the player.
• If you place the player on the cabinet with the HDMI cord connected, do not apply too much pressure to the cabinet wall. It may damage the HDMI OUT jack or the HDMI cord.
• When connecting or disconnecting, do not screw in or rotate the HDMI connector.
11

Step 3: Connecting the Audio Cords

Select the connection that best suits your system. Be sure to read the instructions for the components you wish to connect.
Connection Your setup
A
TV
B
Stereo amplifier (receiver) and two speakers
Notes about the HDMI OUT jack
• When you connect the player to an AV amplifier (receiver) using an HDMI cord, you will need to do one of the following: – Connect the AV amplifier (receiver) to a TV with the HDMI
cord.
– Connect the player to the TV with a video cord other than an
HDMI cord (component video cord, S VIDEO cord, or video cord).
• When connecting to the HDMI OUT jack, carefully align the HDMI connector with the jack. Do not bend or apply pressure to the HDMI cord.
• If you change the component connected to the HDMI OUT jack, change “Audio (HDMI)” in “Audio Setup” to match the new component (page 47). The player stores the HDMI related settings for up to five components.
• The HDMI connection is compatible with 2ch Linear PCM signals (48 to 192 kHz, 16/20/24 bit), and 6 to 8ch Linear PCM signals (48 to 96 kHz, 16/20/24 bit), in addition to Dolby Digital and DTS bit stream (5.1ch signals up to 96 kHz, 16/20/ 24bit).
Note
If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers.
C
AV amplifier (receiver) having a
*1
Dolby decoder and 3 to 6 speakers
• Surround effects: Dolby Surround
AV amplifier (receiver) with
5.1ch input jacks and 6 speakers
• Surround effects: Dolby Digital
AV amplifier (receiver) with a digital input jack having a Dolby Digital or DTS speakers
• Surround effects: Dolby Digital
AV amplifier (receiver) with an HDMI input jack and 8 speakers
• Surround effects: 8ch Linear
Surround (Pro Logic)
(Pro Logic)
D-1
(5.1ch), DTS (5.1ch)
D-2
*2
decoder and 6
(5.1ch), DTS (5.1ch)
D-3
PCM
12
*1
Manufactured under license from Dolby laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.
A

Connecting to your TV

This connection will use your TV’s speakers for sound.
B
Connecting to a stereo amplifier
(receiver) and 2 speakers
If your stereo amplifier (receiver) only has audio input jacks L and R, use . If your amplifier (receiver) has a digital input jack, use .
B-1
B-2
Getting Started
TV
AC IN
INPUT
VIDEO
L
AUDIO
R
(white)
(red)
: Signal flow
HDMI OUT
COMPONENT
VIDEO OUT
VIDEO
OUT
Y
VIDEO
B
P
P
R
S VIDEO
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
AUDIO
OUT
L
R
to AUDIO OUT L/R
(white)
(red)
Stereo audio cord (supplied)
Blu-ray Disc player
5.1CH OUTPUT
FRONT REAR CENTER
L
R
Blu-ray Disc player
COMPONENT VIDEO OUT
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
AC IN
WOOFER
AUDIO
OUT
L
R
B-2 B-1
HDMI OUT
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
B
P
R
S VIDEO
to DIGITAL OUT (COAXIAL or OPTICAL)
Optical digital cord (not supplied)
or
Coaxial digital cord (not supplied)
AUDIO
L
R
OUT
5.1CH OUTPUT
FRONT REAR CENTER
L
R
WOOFER
AUDIO
OUT
L
R
to AUDIO OUT L/R
(red)(white)
Stereo audio cord (supplied)
(white) (red)
to coaxial or optical digital input
to audio input
[Speakers]
Front (L)
Front (R)
Stereo amplifier (receiver)
: Signal flow
,continued
13
C
Connecting to an AV amplifier
D-1

Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro Logic) decoder and 3 to 6 speakers

If your AV amplifier (receiver) only has L and R audio input jacks, use . If your amplifier (receiver) has a digital input jack, use . You can enjoy surround effects only when playing Dolby Surround audio or multi-channel audio (Dolby Digital or DTS) discs.
C-1
C-2
AC IN
C-2 C-1
to DIGITAL OUT (COAXIAL or OPTICAL)
Optical digital cord (not supplied)
Coaxial digital cord (not supplied)
HDMI OUT
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
or
COMPONENT
VIDEO OUT
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
B
P
R
S VIDEO
L
R
AUDIO
OUT
5.1CH OUTPUT
FRONT REAR CENTER
L
R
AUDIO
L
R
WOOFER
OUT
to AUDIO OUT L/R
(red)(white)
Stereo audio cord (supplied)
Blu-ray Disc player
(receiver) with 5.1ch input jacks and 6 speakers
If your AV amplifier (receiver) has 5.1 channel inputs, use
.
D-1
Blu-ray Disc player
COMPONENT
VIDEO OUT
AC IN
to 5.1CH OUTPUT
Stereo audio cord (one is supplied)
D-1
VIDEO
OUT
VIDEO
HDMI OUT
S VIDEO
5.1CH OUTPUT
FRONT REAR CENTER
L
R
Y
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
B
P
R
WOOFER
AUDIO
L
R
OUT
5.1CH OUTPUT
FRONT REAR CENTER
L
R
WOOFER
Monaural audio cord (not supplied)
(red)(white)
to coaxial or optical digital input
[Speakers] [Speakers]
AV Amplifier
to audio input
(receiver) with a decoder
Rear (L) Rear (R)
Subwoofer
Center
Rear (mono)
Front (R)
Front (L)
: Signal flow
Hint
z
For correct speaker location, see the operating instructions of the connected components.
Note
When connecting 6 speakers, you do not need the “Rear (mono)” speaker above.
to audio input
[Speakers] [Speakers]
AV amplifier (receiver) with
5.1ch inputs
Rear (L)
Rear (R)
Center
Front (R)
Subwoofer Front (L)
: Signal flow
Hint
z
For correct speaker location, see the operating instructions of the connected components.
14
D-2
Connecting to an AV amplifier
D-3

Connecting to an AV amplifier (receiver) with a digital input jack and 6 speakers

If you want to use the Dolby Digital, or DTS decoder function on your AV amplifier (receiver), connect to its digital jack using
. You can enjoy a more realistic audio presence.
D-2
Blu-ray Disc player
COMPONENT
VIDEO OUT
AC IN
D-2
HDMI OUT
to HDMI OUT
HDMI cord (supplied with BDP-S301 only)
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
S VIDEO
or
B
P
R
DIGITAL OUT
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
or
HDMI
OUT
5.1CH OUTPUT
AUDIO
OUT
FRONT REAR CENTER
L
L
R
R
WOOFER
to DIGITAL OUT (COAXIAL or OPTICAL)
Coaxial digital cord (not supplied)
Optical digital cord (not supplied)
(receiver) with an HDMI input jack and 8 speakers
If your AV amplifier (receiver) accepts 8ch Linear PCM input with an HDMI connection, you can enjoy the surround sound using .
D-3
Blu-ray Disc player
COMPONENT
VIDEO OUT
AC IN
to HDMI OUT
HDMI cord (supplied with BDP-S301 only)
VIDEO
OUT
Y
DIGITAL OUT
VIDEO
PCM/DTS/DOLBY DIGITAL
COAXIAL OPTICAL
P
HDMI OUT
B
P
R
S VIDEO
D-3
HDMI
OUT
L
R
AUDIO OUT
5.1CH OUTPUT
FRONT REAR CENTER
L
R
WOOFER
Getting Started
to HDMI input
to coaxial or optical digital input
[Speakers] [Speakers]
AV amplifier (receiver) having a decoder
Rear (L)
Rear (R)
Subwoofer
Front (L)
Center
Front (R)
: Signal flow
z Hint
For correct speaker location, see the operating instructions of the connected components.
to HDMI input
[Speakers] [Speakers]
AV amplifier (receiver) with 8ch outputs
z
Rear1 (L)
Hint
Rear1 (R)
Rear2 (L)
Subwoofer
Rear2 (R)
Front (L)
Center
Front (R)
For correct speaker location, see the operating instructions of the connected components.
Note
Not all HDMI-compatible AV amplifiers (receivers) accept 8ch Linear PCM signals. See also the operating instructions supplied with the connected AV amplifier (receiver).
15
Step 4: Connecting the
Step 5: Preparing the
Power Cord
After all of the other connections are complete, connect the supplied power cord to the AC IN terminal of the player. Then plug the player and TV power cords into the AC outlet.
AC IN
to AC IN
to AC outlet
Remote
You can control the player using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the player (page 58).
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or a lighting apparatus. Doing so may cause a malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
16

If you want to control your TV with the supplied remote

You can control the volume, input source, and power switch of your Sony TV with the supplied remote.
OPEN/
TV
CLOSE
TV \/1
Number buttons
MUTING
VOL +/–
By pressing You can
TV [/1 Turn the TV on or off.
VOL +/– Adjust the volume of the TV.
TV/VIDEO
CH +/– Select the channel up and down.
MUTING
DIMMER
DISPLAY
123
456
7809
CLEAR
AUDIO SUBTITLE
RED
GREEN
BLUE
SYSTEM MENU
RETURN
PREV
SLOW/STEP
SCAN
PLAY SCAN
PAUS E
PLAY MODE
VOL CH
MUTING
TV/VIDEO
VIDEO
FORMAT
ANGLE
YELLOW
STOP
NEXT
TOP
MENU
POP UP/
MENU
TV/VIDEO
CH +/–
Switch the TV’s input source between the TV and other input sources.
Mute the sound (for Sony TV only).
To control other TVs with the remote
You can control the volume, input source, and power switch of non­Sony TVs as well. If your TV is listed in the table below, set the appropriate manufacturer’s code.
1 While holding down TV [/1, press the number
buttons to select your TV manufacturer’s code (see the table below).
2 Release TV [/1.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
Manufacturer Code number
Sony 01 (default)
Daewoo 22, 04
Emerson 14
GE 06
Hitachi 02, 04
JVC 09
LG/Gold star 03, 17, 04
MGA/Mitsubishi 13, 04
NEC 04, 12
Panasonic 19
Philips 08, 21
Pioneer 16
RCA 10, 04
R.Shack 05
Samsung 04, 12, 20
Sanyo 11
Sharp 05, 18
Toshiba 07, 18
Zenith 15
To return the remote to its default settings
1 Remove the batteries from the remote. 2 Re-insert the batteries while pressing down 1, 2,
and 3 of the number buttons.
3 Wait for a few seconds.
Getting Started
Note
Depending on the connected unit, you may not be able to control your TV using all or some of the buttons on the supplied remote.
17

Step 6: Easy Setup

Follow the steps below to make the minimum number of basic adjustments for using the player. If you do not complete Easy Setup, it will appear each time you turn on your player. Make the settings below in the following order.
e Select “Start,” and press ENTER to start
“Easy Setup.”
Easy Setup
Before using, make some simple settings for the BD player.
Start Cancel
Please use the Initial Setup if you want to make more detailed settings.
Use to select then press ENTER.
Confirm Exit
SYSTEM MENU
When turned on for the first time
Wait about 90 seconds before the player turns on and starts Easy Setup. The start-up time will be much shorter once Easy Setup is completed.
OPEN/
TV
CLOSE
DIMMER
DISPLAY
123
456
7809
CLEAR
AUDIO SUBTITLE
RED
GREEN
BLUE
SYSTEM MENU
RETURN
PREV
SLOW/STEP
TV/VIDEO
VIDEO
FORMAT
ANGLE
YELLOW
POP UP/
NEXT
MENU
MENU
"/1
TOP
</M/m/,, ENTER
a Turn on the TV.
If the above display does not appear
Go to step 6. This display appears only when the player is turned on for the first time.
f Select the video output format for the
connected TV, and press ENTER.
For details about the video output, see page 46.
When using the HDMI OUT jack
Easy Setup
Output Video Format
Auto 480i 480p 720p 1080i 1080p Source Direct
Select [Auto] to automatically match the video output format with the HDMI-connected TV.
Select from “Auto,” “480i,” “480p,” “720p,” “1080i,” “1080p,” or “Source Direct,” then go to step 8. “TV Type” in step 7 will be set to “16:9” (wide screen).
When using the jacks other than the HDMI OUT jack
Confirm Exit
SYSTEM MENU
b Press [/1 to turn on the player.
The player turns on after a moment.
c Switch the input selector on your TV so that
the signal from the player appears on your TV screen.
If the display for OSD language selection does not appear, select “Start” of “Easy Setup” in “Options” Setup (page 52).
d Select the OSD language you want to display,
and press ENTER.
Easy Setup
Language
English Français
Select the on-screen display language. Audio, subtitle and BD/DVD menu language options will be set to the same language as this.
This will determine the Audio, Subtitle and BD/ DVD menu languages as well.
Confirm Exit
SYSTEM MENU
Easy Setup
Output Video Format
S-Video/Video only 480i 480p 720p 1080i Don't Know
Select [Auto] to automatically match the video output format with the HDMI-connected TV.
Confirm Exit
SYSTEM MENU
Select from “S-Video/Video only,” “480i,” “480p,” “720p,” “1080i” or “Don’t Know.” If you select “720p” or “1080i,” go to step 8. “TV Type” in step 7 will be set to “16:9” (wide screen).
18
g Select the aspect ratio that matches your TV,
and press ENTER.
Step 7: Additional
Easy Setup
TV Type
16:9 4:3
Select the screen aspect ratio to match your TV.
Confirm Exit
SYSTEM MENU
If you have a wide screen TV or a 4:3 standard TV with a wide screen mode
Select “16:9” (page 45).
If you have a 4:3 standard TV
Select “4:3” (page 45).
h Select “Finish Setup,” and press ENTER.
Easy Setup
Setup is complete! Enjoy using your BD player!
Finish Setup Go Back
Use to select then press ENTER.
Confirm Exit
SYSTEM MENU
z Hints
• If you want to reset these settings to their factory defaults, see “Resetting the Player(page 53).
• You can re-run “Easy Setup” from “Options” Setup (page 52).
Adjustments
The following settings and adjustments are necessary when your connection applies.
For video connection
When using the COMPONENT VIDEO OUT jacks
(Pattern Cpage 10)
• Select the video output resolution for your TV by pressing VIDEO FORMAT (page 46).
When using the HDMI OUT jack
(Pattern Dpage 11)
• Select the video output resolution for your TV by pressing VIDEO FORMAT (page 46).
• Select the type of video output from the HDMI OUT jack in “YCbCr/RGBPC (HDMI)” of “Video Setup” (page 45).
For audio connection
When using the DIGITAL OUT (OPTICAL or COAXIAL) jack
(Connection , , page 13 to 15)
• Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47) according to your AV amplifier’s (receiver’s) decoder.
When using the HDMI OUT jack
(HDMI connection of , page 15)
• Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47) according to your AV amplifier’s (receiver’s) decoder.
• Select the audio output method from the HDMI OUT jack in “Audio (HDMI)” of “Audio Setup” (page 47).
When using the AUDIO OUT (L/R) jacks
(Connection page 14)
• Set “DTS Downmix” to “Lt/Rt” in “Audio Setup” (page 47).
When using the 5.1CH OUTPUT jacks
(Connection page 14)
• Set “Audio Output Mode” to “5.1 Channel” in “Speakers” Setup (page 51), and adjust the “Speaker Setup” setting for your system.
B-2 C-2
C-1
D-1
D-2
D-2
D-3
Getting Started
Notes
• If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers.
• If you connect using the HDMI OUT jack or COMPONENT VIDEO OUT jacks and the picture does not appear clearly, the connected display device may not be compatible with the progressive signals. In this case, connect the display device to the S VIDEO jack or the VIDEO jack (pattern A or B – see page 10), re-run the “Easy Setup” from the “Options” Setup (page 52), and select “S-Video/Video only” in step 6 (page 18). Also, check the above items again to see if any additional adjustment is required.
19

Playing a Disc

Basic Operations

Most of the BD playback operations are common to DVD. This section covers BD/ DVD/CD playback in general, together with the basic operation of the player. For browsing recorded files on DATA DVDs*, a separate library function is available. See also page 32 for movie, 36 for music, 40 for photo files. For operations using the remote, a complete list is located on page 24.
* DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs containing
MPEG-2 PS movie, MP3 audio, or JPEG image files.
BD
DVD
Number buttons
SYSTEM MENU
RETURN
CD
OPEN/
TV
CLOSE
Z
DIMMER
DISPLAY
TV/VIDEO
123
456
7809
CLEAR
AUDIO SUBTITLE
RED
SYSTEM MENU
RETURN
PREV
SCAN
PLAY MODE
X
MUTING
GREEN
BLUE
SLOW/STEP
PLAY SCAN
PAUS E
VOL CH
VIDEO
FORMAT
ANGLE
YELLOW
STOP
\/1
Color buttons
TOP
MENU
TOP MENU
</M/m/,, ENTER
POP UP/MENU
POP UP/
MENU
NEXT
H
x
Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . 20
Guide to Displays . . . . . . . . . . . . . . . . . . . . . . 22
Guide to the Remote. . . . . . . . . . . . . . . . . . . . 24
Checking the Disc Information . . . . . . . . . . . . 26
Clarifying Low Volume Sounds (Audio DRC) . 27
Adjusting the Pictures . . . . . . . . . . . . . . . . . . 28
Locking a Disc . . . . . . . . . . . . . . . . . . . . . . . . 29
a Press \/1.
The player turns on after a moment.
b Switch the input selector on your TV so that
the signal from the player appears on your TV screen.
c Press Z to open the disc tray.
d Place a disc on the disc tray with the playback
side facing down.
Playback side facing down
20
e Press Z to close the disc tray.
Wait a short while until the disc type appears on the front panel display.
f Press H to start playback.
For more information about the remote’s operations, see page 24.
Buttons Details
X Pauses playback, or restarts playback from the same
point.
x Stops playback, or cancels the resume point when
pressed twice.
H Starts or restarts playback from the previous stop
point.
g When you finish playing, press Z to open the
disc tray.
h Remove the disc, and press Z again to close
the disc tray.
i Press \/1 to turn off the player.
About the screen saver function
To prevent damage to your display device (ghosting), a screen saver image appears when the player is left unattended, has no disc inserted, or no title/slideshow is displayed for 15 minutes. To cancel, press any button on the remote or the player.
About One-Touch Play (for HDMI connections only)
With one touch of the H button, the player and your TV/AV receiver automatically turn on and the TV/AV receiver’s input is switched to the player. Playback starts automatically. To use this function, set “HDMI Control” of “Options” setup to “On” (page 52). The TV/AV receiver’s input will also switch to the player automatically, in the following cases: – You press H, SYSTEM MENU, TOP MENU, or POP UP/
MENU buttons on the remote.
– A disc with auto playback function is loaded.
Basic Operations
To use the BD’s or DVD’s menu
When you play a BD-ROM, DVD VIDEO, or a finalized DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R (Video mode), you can display the disc’s menu by pressing TOP MENU or POP UP/MENU. Some BDs/DVDs display the menu automatically. Either cases, navigate through the menu using </M/m/,, ENTER, or the number buttons and the color buttons as indicated by the disc’s on-screen instructions. The BD menu is operable without interrupting playback.
To play restricted BDs
If “CAN’T PLAY” appears on the front panel display for a BD­ROM, change the “BD Parental Control” setting (page 30).
To play restricted DVDs
For a restricted DVD, the display asks for the password. For “DVD Parental Control” setting, see page 30.
1 Enter your four-digit password using the number
buttons.
2 Press ENTER to confirm.
To register or change the password, see page 29.
Notes about Resume Play
• Playback starts from the beginning if the title has not been played or the previous stop point is canceled.
• The stop point is canceled when: – you change the settings on the player. – you turn off the player (BD-ROM and CD only). – you press x twice. – you open the disc tray. – you finish a search.
• The player remembers the stop point for one title/track/file only. On a music CD, playback resumes from the beginning of the track.
21

Guide to Displays

BD
When ‘Select an item, and press ENTER’ appears in this manual, press the </M/m/, keys on the remote to select the item then the entry button in the middle. You can operate the player likewise using displays.
DVD
DATA DVD
CD
Title List
For DATA DVDs, this display leads further to the Title Lists of content type. The three Title Lists appear similar and are operable in a similar way.
Title List
Movies
Photos
Music
Access the BD-R/RE titles.
Select Exit
SYSTEM MENU
System Menu
Title List
A/V Control
Setup
Search for the part you want to play from a list of the disc's content.
Select Exit
SYSTEM MENU
a Press SYSTEM MENU to turn on the above
“System Menu.”
The player’s start menu appears, with entries to all of the functions.
b Select an item, and press ENTER.
Each item leads to the following function displays. See the pages in parentheses for operations. When you want to return to the previous display, press RETURN.
Select the Title List you want to view; from “Movies,” “Photos,” or “Music,” and press ENTER.
Movies
Displays movies/video titles only (page 32).
Photos
Displays image files only (page 40).
Music
Displays music files only (page 36).
A/V Control (page 27)
Adjusts the audio/video settings. Select either “Video Control,” or “Audio Control,” and press ENTER.
A/V Control
Video Control
Audio Control
Set the playback picture quality.
Select Exit
SYSTEM MENU
Setup (page 44)
Enters the Setup displays for changing the player’s settings. Select the related Setup display, and press ENTER.
22
Video Setup Audio Setup Language Parental Control Speakers Options
Use ENTER.
Setup
TV Type 4:3 Video Output DVD Aspect Ratio
bCr/RGBPC(HDMI)
YC 24p Output
to select an item, then press [RR] or
16:9 Normal Letter Box
b, Cr
Y, C Off
Confirm Exit
SYSTEM MENU
Loading...
+ 50 hidden pages