Page 1
somat®
Remote Waste Pulping System
Description
Standard SOMAT® Model HE-6S-3 HydraExtractor® with 3 HP drive motor, 3 HP or 5 HP
return pump, chemical additive pump, automatic
rinse system, valve package, Som-A-Trol® control
panel and discharge chute with limit switch.
Benefits
As much as 8 to 1 (87.5%) volume reduction
Reduced labor cost
Better sanitation
Water conservation
Improved operator morale
Reduced silverware loss
Processes a wide variety of waste
Operation: Slurry, consisting of 5% solids and 95%
water, is automatically transported through a pipeline
after being processed in the pulper(s) to the HydraExtractor, where water is removed and the resultant
semi-dry pulp is discharged into a haul-away
container. The extracted water is recovered and
returned to the pulper(s) for reuse. The capacity of
the Hydra-Extractor determines how many pulpers
can be designed to operate with it concurrently.
Somat equipment provides an economic and
efficient answer to cutting the high and ever
increasing costs associated with waste handling.
Manufactured by Somat Company of Lancaster,
Pennsylvania, originators of waste pulping systems
and specialists in waste reduction technology.
Approval:
6/7/06
Item No_______________________________
SOMAT Model: HE-6S-3
Technical Specifications
Hydra-Extractor
Hydra-Extractor: Rigid stainless steel weldment
with aluminum stand, head assembly with 3 HP
TEFC drive motor mounted to a 20:1 gear reducer,
17” long stainless steel discharge chute with limit
switch, chemical additive pump, automatic rinse
system. Water extractor mechanism consists of 6”
diameter stainless steel screw with nylon brush edge,
stainless steel plug cutter and matching 6” diameter
reinforced stainless steel screen.
Valve Package: All valves required for proper
operation (automatic rinse system).
Som-A-Trol® (Electrical Control Panel): UL
approved. Includes all necessary electrical
components prewired to a terminal strip in a NEMA 4
stainless steel enclosure.
Options Available:
Extended discharge chute
Hinged Chute
Extended stand
Pulp level detector
Special electrical characteristics
Special Requirements:
7-1/2 HP, 10 HP or larger return pump,
Determined by piping conditions.
Water economizing tank. Required when 7-1/2 HP
or larger return pump is used.
Pulp Screw Conveyor and controls. Required to
convey pulp from discharge chute to haul-away
container when location of container does not
Electrical Characteristics: 208/230/460 volt,
3 Phase, 60 Hertz
Capacity: 1600 pounds per hour of foodservice
waste mix, consisting of food scraps, plastics, milk
cartons, paper, aluminum foil and cardboard.
Finish: All exterior surfaces, except where polished
stainless steel, are prime coated and finished with
two coats of enamel paint.
Equipment only is supplied by SOMAT Company; installation, piping and
wiring not included.
permit gravity discharge.
Somat Company
Division of ITW Food Equipment Group LLC
165 Independence Court
Lancaster, PA 17601 USA
Tel: 717-397-5100 Fax: 717-291-0877
1-800-237-6628
www.somatcompany.com
Page 2
somat®
Remote Waste Pulping System
SOMAT Model: HE-6S-3
Hydra-Extractor
Somat® Model HE-6S-3 Hydra-Extractor
Utility Connections
E10- Extractor Drive Motor (3Hp) P10- Fresh Hot Water Inlet
E11- Return Pump Motor (3Hp / 5Hp) P11- Overflow Outlet
E12- Chemical Additive Pump P12- Slurry Inlet
E13- Fresh Hot Water Solenoid P13- Return Water Outlet
E14- N/A P14- Autorinse to Drain
E15- Chute Limit Switch
E16- Autorinse MOV
E17- Junction Enclosure
Dimensions
Height: 75” (1905mm) Equipment weight: 525lbs
Length: 41” (1042mm) (Not including chute) Operating weight: 570lbs
Width: 33” (839mm) Crated weight: 625lbs
Crated volume: 59 cu. Ft.
6/7/06
Page 3
somat®
Remote Pulping System
SOMAT Model: HE-6S-3
Hydra-Extractor
Somat® Model HE-6S-3 Hydra-Extractor
Other Utility Requirements
Fresh Hot Water- 4gpm @ 45 psig, 1/2” NPT (approximate usage 160 gallons/cycle)
Drain- 4” minimum floor sink, with stainless steel removable basket recommended
6/7/06
Loading...