Snap-on Vantage Ultra User Manual

User Manual

EAZ0081N01A Rev. A

Trademarks

IMPORTANT:

Snap-on, ShopStre am, ShopStream Connect and Sun are trademarks of Snap-on Incorporated.
All other marks are trademarks or registered trad emarks of their respective holders.

Copyright Information

© 2014 Snap-on Incorporated. All rights reserved.

Disclaimer of Warranties and Limitation of Liabilities

The information, specifications and illustrations in this manual are based on the latest information available at the
time of printing. While the authors have taken due care in the p rep aratio n of this manual, n othing cont aine d here in:

• Modifies or alters in any way the standard terms and co nd itions of the purch ase, lease, or rent al ag reement

under the terms of which the equipment to which this m anual relate s was acquired.

• Increases in any way the liability to the customer or to third parties.

Snap-on reserves the right to make changes at any time without notice.

Before operating or maintaining this unit, please read this manual carefull y paying extra attentio n
to the safety warnings and precautions.

Visit our websites at:

Snap-on

(North America) http://diagnostics.snapon.com
(United Kingdom) www1.snapon.com/diagnostics/uk

ShopStream Connect

(North America) http://www1.snapon.com/diagnostics/us/SSC
(United Kingdom) http://www1.snapon.com/diagnostics/UK/Diagnostics/ShopStreamConnect.htm

For Technical Assistance

Phone / E-mail:

(North America) 1-800-424-7226 / diagnostics_supp [e-mail]
(United Kingdom) [phone] / diagnosticsUKp roduct s upport@sn apon.co m

For technical assistance in all other markets, cont act yo ur selling a gent

EAZ0081N01A Rev. A 27-B-2014 GB

ii

Safety Information

For your own safety and the safety of others, and to prevent damage to the equipment an d
vehicles upon which it is used, it is important that the accompanying Important Safety Instructions
be read and understood by all persons operating, or coming into contact with, the equipment. We
suggest you store a copy near the unit in sight of the operator.

This product is intended for use by properly trained and skilled p rofessional a utomotive
technicians. The safety messages presented throughout this manual are reminders to the
operator to exercise extreme care when using this test instrument.

There are many variations in procedures, techniques, tools, and p art s for servicing vehicles, as
well as in the skill of the individual doing the work. Because of the vast number of test applications
and variations in the products that can be tested with this instrument, we cannot possibly
anticipate or provide advice or safety messages to cover every situation. It is the responsibility of
the automotive technician to be knowledgeable of the system being tested. It is essential to use
proper service methods and test procedures. It is import ant to perform tests in an ap propriate and
acceptable manner that does not endanger your sa fety, the safety of others in the work area, the
equipment being used, or the vehicle being tested.

It is assumed that the operator has a thorough underst anding of vehicle systems before using this
product. An understanding of these system prin cipl es and op erating th eories is ne cessary fo r
competent, safe and accurate use of this instrument.

Before using the equipment, always refer to and follow the safety messages and applicable test
procedures provided by the manufacturer of the vehicle or equipment being tested. Use the
equipment only as described in this manual.

Read, understand and follow all safety messag es and instru ctions in this manual , the
accompanying Important Safety Instr uction s, an d on the test equipm ent.

iii

Safety Information Safety Message Conventions



'$1*( 5



:$51 ,1 *



&$87,21



:$51 ,1 *

Safety Message Conventions

Safety messages are provided to help prevent personal injury and equipm ent damage. All safety
messages are introduced by a signal word indicating the haza rd level.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury to the operator or to bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in death o r serious
injury to the operator or to bystanders.

Indicates a potentially hazardous situation which, if not a voided, may result in moderate or minor
injury to the operator or to bystanders.

Safety messages contain three different type styles.

• Normal type states the hazard.

• Bold type states how to avoid the hazard.

• Italic type states the possible consequences of not avoidi ng the ha zard.

An icon, when present, gives a graphical description of the potential hazard.
Example:

Risk of unexpected vehicle movement.

• Block drive wheels before performing a test with engine running.

A moving vehicle can cause injury.

Important Safety Instructions

For a complete list of safety messages, refer to the accompanying Import ant Safety Instructions.

SAVE THESE INSTRUCTIONS

iv

Content s

Safety Information...............................................................................................................iii

Chapter 1: Using This Manual.............................................................................................3

Conventions............................................................................................................................3

Bold Text..........................................................................................................................3

Symbols ...........................................................................................................................3

Terminology .....................................................................................................................3

Notes and Important Messages.......................................................................................4

Hyperlinks ........................................................................................................................4

Procedures.......................................................................................................................4

Chapter 2: Introduction........................................................................................................5

Functional Description................................................................................................ .... ... .....5

Technical Specifications.........................................................................................................7

Control Keys...........................................................................................................................8

Accept (Y/a) Key .............................................................................................................8

Directional Keys...............................................................................................................8

Cancel (N/X) Key .... ... ... .... ...................................... .... ... ... ... ... .... ... ..................................8

S (Shortcut) Key...............................................................................................................9

Power Key........................................................................................................................9

Power Sources.......................................................................................................................9

Internal Battery. .......................................... .... ... ... .......................................... ... ... .... ........9

AC/DC Power Supply.......................................................................................................9

The Stand...............................................................................................................................9

Chapter 3: Getting Started.................................................................................................10

Powering Up.........................................................................................................................10

Home Screen........................................................................................................................10

Title Bar..........................................................................................................................10

Home Screen Buttons....................................................................................................11

Powering Down ....................................................................................................................12

Emergency Shutdown............. .......................................... ... ... .... ...................................12

Chapter 4: Navigation ........................................................................................................13

Screen Messages.................................................................................................................13

Loading and Connecting Messages...............................................................................13

Confirmation Messages .................................................................................................13

Warning Messages ........................................................................................................13

Error Messages..............................................................................................................13

Navigation.............................................................................................................................13

Screen Layout................................................................................................................14

Chapter 5: Guided Component Tests...............................................................................17

Vehicle Identification.............................................................................................................17

Identifying a Test Vehicle...............................................................................................17

1

Top Level Menu Options ............................................................... .... ... ... ... .... ... ... ... .............19

Power User Tests ..........................................................................................................19

How To Guide................................................................................................................19

Features and Benefits....................................................................................................19

Index ..............................................................................................................................19

Operations............................................................................................................................20

Component Information .................................................................................................20

Tests ..............................................................................................................................21

Chapter 6: Scope Multimeter Operations.........................................................................24

Getting Started .....................................................................................................................24

Capabilities ....................................................................................................................24

Leads and Adapters.......................................................................................................26

Operations............................................................................................................................28

Starting the Scope and Multimeter.................................................................................28

Measurement Out of Range...........................................................................................29

Scope and Multimeter Setup..........................................................................................30

Chapter 7: Previous Vehicles and Data............................................................................39

Vehicle History......................................................................................................................39

View Saved Data..................................................................................................................40

Delete Saved Data ............................................................ ... ... ... ... .... ... ... ... ..........................40

Chapter 8: Tools.................................................................................................................42

Tools Menu...........................................................................................................................42

Connect-to-PC ...............................................................................................................42

Configure Shortcut Key..................................................................................................43

System Information........................... ... ... .......................................... .............................43

Settings..........................................................................................................................44

Chapter 9: Maintenance.....................................................................................................52

Cleaning and Inspecting the Diagnostic Tool.......................................................................52

Cleaning the Touch Screen ...........................................................................................52

Battery Service.....................................................................................................................52

Battery Safety Guidelines ..............................................................................................53

Replacing the Battery Pack..................................... .... ... .......................................... ... ...53

Disposing of the Batteries....................................... .... ... ... ... ... .... ... ... ... .... ... ... ................54

Index....................................................................................................................................55

2

Chapter 1 Using This Manual

This manual contains tool usage instructions. Some of the illustrations shown in this manual may
contain modules and optional equipment that are not included on your system. Contact yo ur sales
representative for availability of other modules and optional equipment.

1.1 Conventions

The following conventions are used.

1.1.1 Bold Text

Bold emphasis is used in procedures to highlight selectab le items such as buttons an d menu
options.

Example:

• Press the OK button.

1.1.2 Symbols

Different types of arrows are used.
The “greater than” arrow (>) indicates an abbreviated set o f se lection instructions.
Example:

• Select Tools > Connect-to-PC.

The example statement abbreviates the following pr ocedur e:

1. Select Tools from the home screen.

2. Highlight Connect-to-PC on the Tools menu.

3. Select Connect-to-PC.
The solid arrows (e, c, d, b) are navigational instructions referring to the four directions of the

directional arrow keys.
Example:

• Press the down d arrow .

1.1.3 Terminology

The term “select” means tapping an item on the tou ch screen, or highlightin g a button or me nu
item and pressing the Accept, OK, Yes, or other similar button to confirm the selection.

Example:

• Select Brightness.

The above statement abbreviates the following procedure :

3

Using This Manual Conventions

NOTE:

IMPORTANT:

IMPORTANT:

1. Navigate to and highlight the Brightness selection.

2. Press the OK, or similar, button.

1.1.4 Notes and Important Messages

The following messages are used.

Notes

A NOTE provides helpful information such as additional explanations, tips, and comment s.
Example:

i For additional information refer to the Global OBD Vehicle Communications Sof t ware Manua l.

Important

IMPORTANT indicates a situation which, if not avoided, may result in damage to the test
equipment or vehicle.

Example:

Do not disconnect the data cable while the Scanner is communica ting with the ECM.

1.1.5 Hyperlinks

Hyperlinks, or hot links, that take you to other related articles, procedures, and illustrations are
available in electronic documents. Blue colored text indica tes a se lect able hyp erlink.

Example:

Read all applicable Safety Information before using this tool!

1.1.6 Procedures

An arrow icon in the left-margin area indicates a pr ocedure.
Example:

z To change screen views:

1. Select the Graph icon.
The dropdown menu displays.

2. Select an option from the menu.
The screen layout changes to the format selected.

4

Chapter 2 Introduction











The V a nt age Ultra is a multi- functi on tool th at comb ines a two-channel la b scope, gra phing
multimeter , and th e exclusive Snap-on Guided Compo nent Tests database into a single unit.

This chapter describes the construction of the diagnostic tool an d addresses the use of the ba sic
hardware controls and features in the following sections:

• Functional Description

• Technical Specifications‚ on page 7

• Control Keys‚ on page 8

• Power Sources‚ on page 9

• The St and‚ o n p age 9

2.1 Functional Description

1— N/X key (No, Cancel, or Return)
2— Y/a key (Yes, Accept, or Continue)
3— Directional key; left (e), right (c), up (b), down (d)
4— Shortcut k ey
5— Power key

Figure 2-1 Front view

5

Introduction Functional Description





5$7,1*±9'&0$;:

61$321,1&25325$7('

$//5,*+765(6(59('

1279$/,':,7+2876(5,$/180%(5







*1'  

9

6'

1— Battery Status Indicator LED (light emitting diode)
2— DC Power Supply Inpu t Port
3— Mini USB Client Port
4— Micro secure digital (microSD) Card Port

Figure 2-2 Top view

1— Collapsible Stand (closed)
2— Battery Compartment Cover

Figure 2-3 Back view

6

Introduction T echnical Specifications

2.2 Technical Specifications

T ouc h Screen

Resistive Touch Panel

Display:

8.0 inch diagonal, Color LCD

800 x 480 resolution SWVGA

Battery:

Rechargeable lithium-ion battery pack
Approximately 3 hour run time
Approximately 5 hour charge time

DC Jack Operating Voltage

10V and 28V DC

Dimensions:

Width:

12.9 inches

327.2 mm

Height:

6.5 inches
165 mm

Depth:

2.04 inches

51.8 mm

Weight (including battery):

3.2 lbs.

1.45 kg

Operating Temperature Range (ambient):

At 0 to 90% relative humidity (non-condensing)

32 to 113°F
0 to 45°C

Storage Temperature (ambient):

At 0 to 70% relative humidity (non-condensing)

–4 to 140°F
–20 to 60°C

Meter

Category I

Environmental Conditions:

This product is intended for indoor use only.
This product is rated for Pollution Degree 2 (normal conditions).

Power Supply:

Supply Rating; 15 VDC, 2A

7

Introduction Control Keys

2.3 Control Keys

There are five control keys located on the right side of the unit near the handgr ip:

Key Icon Description

Selects a menu or program, advances to the

Accept, Yes

next screen, or provides a yes answer to a
question on the screen.

Directional, Arrows

Cancel, No

Shortcut

Power, On/Off

All other tool operations are controlled through the touch screen.

2.3.1 Accept (Y/a) Key

The Y/a key is used to do the following:

• To select an item that was highlighted using the direction arrows.

• To advance to the next screen in a series.

• To answer “Yes” when a yes or no choice is given.

Moves the highlight on the display screen up,
down, left, and right, as indicated by the arrows.

Exits a menu or program, returns to the
previous screen, or provides a no answer to a
question on the screen.

A function key that can be programmed to
provide a shortcut for performing a variety of
routine tasks.

Turns the unit on and off. Also, press and hold
for 5 seconds for emergency shutdown.

2.3.2 Directional Keys

The directional, or arrow, keys move the cursor or highlight in their re spective direction:

• Up (b)

• Down (d)

• Left (e)

• Right (c)

2.3.3 Cancel (N/X) Key

The N/X key is used to do the following:

• To exit a menu or program.

• To close an open list and return to the previous menu.

• To answer “No” when a yes or no choice is given.

8

Introduction Power Sources

2.3.4 S (Shortcut) Key

Use the Shortcut key to quickly perform routine tasks, such as capturing an image of the current
screen, with a single press. The Shortcut, or S, key can be programmed to perform a numbe r of
different functions. Refer to Configure Shortcut Key‚ on page 43 for a dditio nal inform ation.

2.3.5 Power Key

The Power key powers up the tool, and turns it off.

2.4 Power Sources

Your diagnostic tool can receive power from the following sources:

• Internal Battery

• AC/DC Power Supply

2.4.1 Internal Battery

The tool can be powered from the internal recharge able battery. A fully charged standard battery
provides sufficient power for about 3 hour s of cont inuous op eration.

An LED on top of the unit (Figure 2-2) illuminates to indicate DC power is being supplied to the
tool. The internal battery is recharged when ever an e xternal po wer sou rce is provided.

2.4.2 AC/DC Power Supply

The diagnostic tool can be powered from a st anda rd wall socke t using the AC/DC power supp ly
and power adapter . The jack on the outp ut cable of th e AC/DC powe r supply att aches to the DC
power supply input port on top of the diagnostic tool. Use only the AC/DC power supply provided.

2.5 The St and

The built-in stand extends from the back of the unit to allow h ands- free viewing. The stand clips
into the unit for storage and pivots out so the display is a t an angle when in use.

9

Chapter 3 Getting Started





Make sure the diagnostic tool has a charged battery p ack, or is connected to an AC power supply .

3.1 Powering Up

Press the Power key on the front of the unit to switch the tool on.

3.2 Home Screen

The main body of the Home screen has four selectable buttons, one fo r each of the primary
diagnostic tool functions. These are explained briefly in the next section and discussed in det ail in
the Navigation chapter.

1— Titlebar
2— Main Body

Figure 3-1 Sample Home screen

3.2.1 Title Bar

The title bar at the top of the screen provides basic information about curren t tool oper ating
conditions. Title bar options vary depending upon vehicle make and model, what module is being
used, what test is being performed, or what menu is selected. The title bar cont a ins information
only , th ere are n o select a ble items.

10

Getting Started Home Screen

Elements of the Title bar let you know at a glance:

• What diagnostic module is currently active.

• The source and status of the power being supplied to th e tool.

• The current time.

An icon depicting the module in use is always along the left-hand edge of the T itle bar. These icons
resemble their Home screen button counterp art s in appear ance and color. The name of the
module displays to the right of the icon on some screens.

An icon at the right-hand edge of the T itl e bar depicts the power supply and status:

Table 3-1 Title bar icons

Icon Definition

Indicates power is being supplied by the internal battery
pack. A fully charged battery is shown. The horizontal
bars on the icon diminish as the battery discharges.

Indicates the internal battery pack is weak and needs to
be recharged immediately. A warning message will also
display on the screen when the battery gets this low.

Indicates power is being supplied by an external source,
such as the AC/DC Power Supply.

A communication icon displays along side the power supply icon whenever the dia gnostic too l is
actively communicating with a personal computer:

A real time clock displays to the left of the icons. The clock is powered by a dedicated internal
battery, so the correct time is maintained even when the main battery pack is discharged. Use the
Tools module to set the clock and format how time is displayed. See Clock Settings‚ on page 47
for additional information.

The Title bar displays o ther information that varies depending upon wha t functions ar e being
performed. Other data may include:

• The identification (ID) of the test vehicle

• The name of the active menu or module

• The name of the test being performed

3.2.2 Home Screen Buttons

The Home screen, which the diagnostic tool auto matically opens to whenever power is supplied
to the unit, allows you to select which of the primary tool functions, or modules to use. Each

Indicates the diagnostic tool is actively communicating
with a personal computer.

11

Getting Started Powering Down

available module is represented by a button on the home screen. Tap a module button to load and
open that tool function. The table below gives brief descriptions of the button opera tions.

Table 3-2 Home screen buttons

Name Button Description

Guided Component
Tests

Scope Multimeter

Previous
Vehicle & Data

Tools

Opens a diagnostic database of specific tests for the
identified vehicle. See Guided Component Tests‚ on
page 17.

Configures the unit to operate as a lab scope,
graphing multimeter, or digital multimeter . See Scope

Multimeter Operations‚ on page 24.

Use to connect to a recently tested vehicle, or to
access saved data files. See Previous V ehicles and

Data‚ on page 39 for details.

to adjust tool settings to your personal

Select

preferences, to access operating system
information, and perform other special
functions

. See Tools‚ on page 42 for details.

Select from the Home screen buttons to begin testing by t apping dir ectly on the button. You can
also use the keypad and Y/a key to activate a module, a yellow border around the button indicates
it is highlighted, or in focus. Use the Directional arrows (e, c, b, d) to highlight the desired
module and press Y/a to select it. A “please wait” message may display briefly, then automatically
clear once the module is loaded and ready for use.

3.3 Powering Down

Press the Power key to turn the diagnostic tool off.

3.3.1 Emergency Shutdown

In case of emergency, press and hold the Power key for five seconds to force a shutdown.

12

Chapter 4 Navigation

This chapter describes the screen layout, how to navigate the interface, a nd how to make
selections using screen menus, buttons, and keys. It also explains the various types of messages
that display while using the tool. The chapter is divided into the following sections:

• Screen Messages

• Navigation‚ on page 13

4.1 Screen Messages

There are four types of on-screen messages:

• Loading and connecting

• Confirmation

• Warning

• Error

4.1.1 Loading and Connecting Messages

Loading and connecting messages display when the diagno stic tool is performin g an internal
operation, such as loading a database, initiating a test, or esta blishing communication s with the
vehicle. The message automatically clears once the internal operation is complete.

4.1.2 Confirmation Messages

Confirmation messages inform you when you are about to perform an a ction that can not be
reversed or when an action that requires your confirmation to co ntinue has b een initiated.

When a response is not required, the message displays briefly , then disappea rs.

4.1.3 Warning Messages

Warning messages inform you wh en co mpleting the selected action may result in an irreversible
change or loss of data. W arning m essages req uire a response in order to continue.

4.1.4 Error Messages

Error messages inform you when a system or procedural error has occurre d.

4.2 Navigation

This section describes general navigation for Guided Compone nt Test s and Scope Mu ltimeter
screens. Although there are some differences, the interf ace operates similar ly for b oth modules.

13

Navigation Navigation

4.2.1 Screen Layout









1— Toolbar—contains test controls
2— Main Body—displays menus and test data
3— Information Panel—shows test and tool status
4— Expand/Collapse icon—operates like the toolbar button, see Table 4-1

Figure 4-1 Sample Guided Component Tests screen

A typical Scope Multimeter screen would be similar to the Guided Component Tests screen shown
above, and navigation is similar as well. The differences are in the infor mation that is being
displayed on the screen, and how the data is gathe red.

Guided Component Tests data is vehicle specific. Therefore, the meter that displays is configured
to perform the selected test on the identified vehicle. In addition to displaying test results;
procedures, tips, and specifications for the selected test ar e availabl e at the touch of a b utton.

Scope Multimeter tests are more general a nd not ti ed to a specific vehicle. T herefore, there is no
need to go through the vehicle identificati on sequence when u sing the Sco pe Multimeter.
However, mor e adjustme nt s to th e meter setting s are usua lly need ed and th e suppor ting
information is not available.

Toolbar

The toolbar , located under the title bar, contains a number of selecta ble tool control buttons. What
buttons appear on the toolbar varies, as only buttons that are active or available for the current
screen and test mode display.

14

Navigation Navigation

A brief description of common toolbar button operatio ns are shown in Table 4-1.

Table 4-1 Guided Component Tests and Scope Multimeter toolbar buttons

Button Icon Function

Back

Home

Previous Screen

Next Screen

Previous Point

Next Point

Stop

Returns to the previously viewed screen. This button is always
at the left-hand edge of the toolbar.

Returns to the Home screen. This button is always alongside
the Back button on the left of the toolbar.

Moves forward one complete screen at a time when viewing
recorded or paused data.

Moves forward one complete screen at a time when viewing
recorded or paused data.

Moves back one data point with each button push when
viewing recorded or paused data.

Moves forward one data point with each button push when
viewing recorded or paused data.

Stops the collection of data, which allows you to more closely
examine the trace and to review the data that is being held in
the memory buffer.

Record

Profile

Cursors

Expand/Collapse

Save

Tools

Indicates that data collection has been paused and the data
being displayed is not being updated. Selecting resumes data
collection.

Opens and closes a field of controls at the bottom of the
screen that allows you to adjust certain attributes of how the
sampled signal displays.

Turns the cursors on and off. The cursors are two vertical
rules that can be repositioned on the screen to measure
intervals.

Expands the meter display to fill the entire screen, or
collapses the meter to show the information panel or profile
details at the bottom of the screen

Saves a recording of the data being displayed on the screen
along with the data that is being held in the memory buffer.

Opens the tools menu, which allows you to adjust basic tool
settings.

15

Navigation Navigation

Additional buttons appear on the toolbar when special operations are available. These buttons are
explained in the operations chapters where applicable.

Main Body

The main body of a Guided Component Test screen displays one of three things:

• A selectable menu

• Component information

• A test meter

The main body of a Scope Multimeter screen displays:

• A selectable menu

• A test meter

Select from a menu using the touch screen or the control buttons.
Component Information screens contain information to assist you with testing.
Test meters can display two circuit traces, or waveforms, si mult a ne ously. Adjustments to the

display are made through the toolbar. Each trace is displayed as voltage over time on a st andard
oscilloscope screen. Voltage level is recorded on the vertical, or “y”, axis and time is presented on
the horizontal, or “x”, axis of the screen. Values are shown for each graduation on the scales.

Touch screen functionality within the main body of the screen is limited, most adjustments are
performed from the T oolbar and the Profile window. However, you can adjust the following in the
main body:

• Trigger position; touch an d drag th e trigge r indicator (+) to r eposition it.

• The expand/collapse icon in the upper-ri ght corner of the main body performs the same

function as the Expand/Collapse button on the Toolbar.

• The baseline position (0 value) of the trace can be repositione d on the hor izont a l scale by

touching and dragging the solid bar at the right-en d of the channel ba seline.

Information Panel

The information panel at the base of th e screen shows either test dat a or Profile det ails in Guided
Component T ests, and Profile details only in Scope Multimeter. Refer to Guided Component Test s‚
on page 17 and Scope Multim eter Opera tions‚ on p age 24 for details.

16

Chapter 5 Guided Component Tests

The Guided Component Tests software provides you with a rob ust diagnostic dat a base fo r use
with scopes and meters. It is like having access to a complete library of shop manuals for testing
engine management, transmission control, and ABS compon ent s.

Guided Component Tests helps you with everything from se lecting the app ropriate test fo r a
specific part to pointing out the best location to hook-up the test leads and the pin configuration
of the connector.

The component test procedures, tips, and meter settings r educe your over all set-up and
diagnostic testing time. V ehicle- specific compo nent tests are provided for engine, transmission,
ABS, charging, transfer case and suspension systems. Availability varies by vehicle.

5.1 Vehicle Identification

The information presented is specific to the vehicle being tested. Therefore, certain attributes of
the test vehicle must be entered into the unit so that the correct data can be retrieved. Vehicle
identification information is carried over if you enter Guided Compon ent Tests from a file store d in
Vehicle History. However, you may need to enter additional attributes in some inst ances.

The vehicle identification sequence is menu driven, you simply follow th e screen prom pt s and
make a series of choices. Each selection you make advances you to the next screen.

5.1.1 Identifying a Test V ehicle

Exact procedures to identify the test vehicle may vary somewhat by vehicle a nd mar ket. The
following procedure, which identifies a 2008 Ford Focus for testing the fuel injection system, is
typical of what to expect.

z To identify a vehicle for Guided Component Tests:

1. Tap the Guided Component T ests button on the Home screen.

2. Select FORD from the list of manufacturers.
A list of model years displays.

3. Select 2008 from the list of years.
A list of models displays.

4. Scroll and select Focus from the list of models.
A list of engines displays.

5. Select 1.6L SIGMA = B from the list of engines.
A confirmation screen displays (Figure 5-1).

17

Guided Component Tests Vehicle Identification

Figure 5-1 Sample confirmation dialog box

6. Select OK from the confirmation screen.
A list of systems available for testing displays (Figure 5-2).

Figure 5-2 Sample available systems menu

7. Select ENGINE and a list of tests available for the identified vehicle displays.

8. Select a test from the list to continue.

The identification sequence is now complete, refer to the Operations section that follows for
details on how to navigate through the Guided Compon ent Test s information and perfor m test s.

18

Guided Component Tests Top Level Menu Options

5.2 Top Level Menu Options

There are additional toolbar buttons, known a s the T op Level Menu buttons, tha t are only available
on the Guided Component Tests System Selection screen. Each button op ens an additional menu
of supplemental information designed to help you ge t the most out of the Guided Co mponent
Tests module. Top Level Menu options include:

• Power User Tests

• How To Guide

• Features and Benefits

• Index

Figure 5-3 Sample Top Level Menu Option buttons

5.2.1 Power User Tests

The Power User Tests option gives you quick access to a pre-configured me ter for conducting a
number of control system tests. Tests are available with or without on-screen help. Help typically
provides a description of the test along with expected results and a link to th e pre-set meter.

5.2.2 How To Guide

The How To option provides a list of available on-screen instructions for performing tasks. Scroll
to view the entire list of guide available.

5.2.3 Features and Benefits

Selecting Features and Benefits opens a menu page, scroll to view the entire list of options.
The optional demonstration board transmits a n umber of adjustable electronic signals similar to

what is commonly found on modern vehicles. The demonstration board not only he lp s you learn
how to use the Guided Component T ests sof tware, it allows you to hone your skills and diagnostic
techniques without an actual test vehicle. Contact your sales representative for details.

5.2.4 Index

This feature allows you to access detailed service information an d specifications for a specific
component. Index is only available in Europe at this time.

Selecting Index opens an alphabetical list of compone nts, systems, test s, terms, and other items
for which there is a brief help file. Some items open an additional men u. Use the Back and Exit
buttons on the Toolbar to return or close the scre en.

19

Guided Component Tests Operations

NOTE:

5.3 Operations

The Guided Component Tests software pr ovides vehicle specific co mponent test procedures and
information that aid in setting up scopes and me ters. Once a test vehicle is identified, you can
select a component test from the list of available tests. A Guided Component Test s menu displays
once a component is selected, two types of information are available o n the menu:

1. COMPONENT INFORMATION—provides inform ation on the selected compon ent a nd
connector pin details that assists you in under st and ing the comp onent s prior to dia gnosis.

2. TESTS—opens a pre-configured meter for performing the selected test, instructions for
performing the test, and offers tips and resources to reduce setup and testing time.

5.3.1 Component Information

Use the Component Information to get details on component o peration .

z To view component information:

1. Select a component from the tests list.

2. Select COMPONENT INFORMATION from the comp onent men u.

i An additional selection, such as front or rear for an oxygen sensor (O2S), may be required before

advancing to the component information screen.

Component information displays in the main body of the screen (Figure 5-4).

Figure 5-4 Sample Component Information screen

20

Guided Component Tests Operations

Screens are divided into up to four sections to help quickly guide you to the correct
information:

– Operation—provides a general description of normal component operation.
– T ech note—provides com ponent related tip s (for example, common failures or faults) as

well as information on factory updates and recalls.

– Connector—displays the component connector and lists pin assignments.
– Location—identifies the component location and the best place for testing it.

3. Use the scroll bar along the right edge of the screen to view a ny additional information .

4. Select Back on the Toolbar , or pr ess the N/X key, to return to the component menu.

5.3.2 Tests

The Tests section guides you through the process of perfo rming test s on a sp ecific componen t.
Selecting a component test gives you access to specifications, tips on how and where to connect
the test meter leads, and configures a meter to perform the specific te st.

z To select a test:

1. Select a component from the list.

2. Select a test from the component menu.
The component menu lists all of the tests availab le for the selected component, choice s vary

by the type of component as well as the make, model, and year of the vehicle.
Selecting opens an additional menu similar to the one shown in Figure 5-5 when multiple

choices are available.

Figure 5-5 Sample O2 Sensors submenu

21

Guided Component Tests Operations

NOTE:

i There may be several levels of submenus for certain components. Select from the menus as

needed to get to the test screen.

3. Select an option from the Guided Component Tests list and the test screen displays
(Figure 5-6).

Figure 5-6 Sample Test screen

A Guided Component Test initially opens with the information panel below the main body of
the screen visible. T ypically, connection information is on the screen and a scroll indicator
displays along the right edge if there is additional infor mation below what is sh own.

4. Tap the Expand/Collapse on the toolba r to view the test mete r only.

5. Select Back on the toolbar to return to the menu.

Adjusting Profile

The pre-configured meter can be used as is for conducting most component test s. However, th ere
are some instances you may want to make adjustments in or der to capture a better image of circuit
activity . This is d one by selecting the Profile button from the toolbar.

22

Guided Component Tests Operations

Figure 5-7 Sample Profile window

z To adjust profile:

1. Select Profile from the toolbar.
The Profile window opens below the main body of the screen.

2. Use the touch screen or the control keys to make changes to the Profile:

– Profile—switches the trace on and off.
– Probe—identifies the type of test probe being used.
– Peak—maximizes the signal sampling rate for capturing fast events, such as voltage

spikes, dropouts, and glitches.

– Filter—removes noise and interference from the trace.
– Invert—switches the polarity of the displayed signal.
– Coupling AC—blocks the DC portion of an input signal in order to amplify the AC portion.
– Scale—adjusts the total value displayed on the vertical axis of the display.
– Trigger—switches triggering on or off, and determines the slope of the trace trigger.

3. Tap Profile on the toolbar or press N/X to move focus back to the toolbar once you are
finished making adjustments.

For more detailed information about adjusting how a sampled signal displays on the screen refer
to Trace Controls‚ on page 30.

23

Chapter 6 Scope Multimeter Operations

The Scope Multimeter module provides all the tools needed for per forming cir cuit tests and for
monitoring signals and circuit activity.

6.1 Getting St arted

The Scope and Multimeter enables your diagnostic tool to function a s either a d igit al multime ter
(DMM), a graphing multimeter, or a 2-channel oscilloscope.

6.1.1 Capabilities

The following tables detail the software and hardware capabilities:

• Scope

• Graphing Multimeter

• Digital Meter

Table 6-1 Scope

Function Range Accuracy/Comments

Signal
Measurement

Sample Rate

Band Width 3 MHz 3 db point @ 3 MHz

Input Impedance

VDC (Full Scale) 100mV–400V Do not measure greater than 75VDC
VAC (Full Scale) 100mV–400V Do not measure greater than 50 VAC (rms)

Low Amp Probe

1. Do not use the Low Amp Probe to measure current on conductors at a potential greater than 46VAC
peak or 70VDC.

Ch. 1—banana jack, yellow
Ch. 2—banana jack, green

For 50uS sweep 6MSPS
For 100uS sweep 3MSPS
For all other sweeps 1.5 MSPS

10 Mohm @ DC
4 kohm @ 3 MHz

20A scale (100mV/Amp)
40A scale (10mV/Amp)
60A scale (10mV/Amp)

Each channel input is referenced to
common ground (GND—black banana jack)

Continuous sampling,
MSPS = mega samples per second

Channel 1 and 2

Connect the positive (+) Amp Probe lead to
the yellow port on the diagnostic tool for
values on Ch.1, or to the green port on the
tool for values on Ch. 2. Connect the
negative (–) lead to GND (black port)

1

.

24

Scope Multimeter Operations Getting Started

Table 6-2 Graphing Multimeter

Function Range Accuracy/Comments

Signal
Measurement

Sample Rate 1.5 MSPS

Ch. 1—banana jack, yellow
Ch. 2—banana jack, green

Each channel input is referenced to
common ground (GND—black banana jack)

Continuous sampling,
MSPS = mega samples per second

Band Width 3 MHz 3 db point @ 3 MHz

Input Impedance

10 Mohm @ DC
4 kohm @ 3 MHz

Channel 1 and 2

VDC (Full Scale) 75VDC Do not measure greater than 75VDC
VAC (Full Scale) 50VDC Do not measure greater than 50 VDC (rms)
Ohm Measurement

Diode Test
Continuity Test

Ch. 1— banana jack, yellow (–)
Ch. 2— banana jack, green (+)

Ohms 40 Ohm—4Mohm Fixed scales

Connect the positive (+) Amp Probe lead to

Low Amp Probe

20A scale (100mV/Amp)
40A scale (10mV/Amp)
60A scale (10mV/Amp)

the yellow port on the diagnostic tool for
values on Ch.1, or to the green port on the
tool for values on Ch. 2. Connect the
negative (–) lead to GND (black port)

1

.

1. Do not use the Low Amp Probe to measure current on conductors at a potential greater than 46VAC
peak or 70VDC.

Table 6-3 Digital Meter

Function Range Accuracy/Comments

Signal
Measurement

Ch. 1—banana jack, yellow

Input is referenced to common ground

(GND—black banana jack)
VDC (Full Scale) 75VDC Do not measure greater than 75VDC
VAC (Full Scale) 50VAC Do not measure greater than 50 VAC (rms)
Signal

Measurement

10 Mohm

Input Impedance
Ohm Measurement

Diode Test
Continuity Test

Ch. 1— banana jack, yellow (–)
Ch. 2— banana jack, green (+)

Ohms 40 Ohm—4Mohm Fixed scales or auto ranging
Glitch Capture Approximately 50 uS
Diode test 2V scale

25

Scope Multimeter Operations Getting Started

IMPORTANT:

6.1.2 Leads and Adapters

The Scope Multimeter uses standard safety plugs that are compatible with many accessories. The
leads, clips, and adapters supplied with or available for the unit are e xplained in this se ction.

When removing leads from their sockets, do not pull on the wire because it can damage the leads.
Pull on the plug.

Channel 1 Lead

The shielded yellow lead is used for Channel 1 (Figure 6-1). The lead color matches the color of
socket 1 on the Display Device and the color of trace 1 on the test screens.

Figure 6-1 Yellow Channel 1 Lead

This yellow lead includes a black, right-angle, common ground plug and a b lack, st ackable,
common ground plug. The non-stacka ble ground plug always con nects to the gr ound (GND) port
on top of the unit. The stackable ground plug is used for connecting a dditional leads, such as th e
Channel 2 Lead or the Secondary Coil Adapter Lead, that require grounding. The stackabl e lead
grounds through the non-stacka ble lead and does not need to be conn ected to the port on the unit.

Channel 2 Lead

The shielded green lead (Figure 6-2) is used for Cha nnel 2. The lea d color matche s the color of
socket 2 on the Display Device and the color of trace 2 on the test screens. This green lead
includes a stackable, black, right-angle ground p lug.

Figure 6-2 Green Channel 2 lead

Alligator Clips

Insulated alligator clips that attach to the test leads are included. The alligator clips are color coded
to match each test lead. Alligator clips attach to the probe end of the test lead (Figure 6-3).

Figure 6-3 Alligator clips

26

Scope Multimeter Operations Getting Started

Secondary Coil Adapter Lead (optional)

The optional Secondary Coil Adapter lead (Figure 6-4) connects to the clip-on secondary wire
adapter , coil-in- cap adapte r or coil-on -plug adap ter to display secon dary wavefor ms.

Figure 6-4 Secondary Coil Adapter lead

Secondary Ignition Clip-on Wire Adapter (optional)

The optional Secondary Ignition Clip-on Wire Adapter (Figure 6-5) connects the Seconda ry Coil
Adapter lead to the vehicle secondary wire to display ignition patterns.

Figure 6-5 Secondary Ignition Clip-on Wire Adapter

Low Amp Current Probe (optional)

The optional Low Amp Current Probe (Figure 6-6) provides accurate and reliable non-intrusive
testing of ignition coils, fuel injectors, fuel pumps, relays, electric motors, and parasitic draw . Use
the Low Amp Current Probe to measure current fr om 10 mA to 60 Amps with a re solution of 1 mA.

Figure 6-6 Low Amp Current Probe

27

Scope Multimeter Operations Operations

6.2 Operations

This section describes configuring the scope or meter and performing te st s.

6.2.1 St arting the Scope and Multimeter

Use the following procedure to set up the scope multimeter for performin g test s.

z To start the scope multimeter:

1. Select the Scope Multimeter button on the Home screen.
The Scope Multimeter main menu opens and of fers th e following setup options:

– Lab Scope
– Graphing Multimeter
– Digital Multimeter

2. Tap to select an option.
A submenu of scope or meter configuration displays, see below for additional infor mation.

3. Tap to select the correct configuration for the tests to be perfor med.
The Scope Multimeter displays configured for the selected te st.

Lab Scope Options

The following options are available for testing:

• 2 Channel Lab Scope

• Volt s DC

• Low Amps (20)

• Low Amps (40)

• Low Amps (60)

• Ignition Probe

• 100 PSI V acuu m

• 100 PSI Pressure

• 500 PSI Pressure

• 5000 PSI Pressure

• MT5030 Vacuum

• MT5030 Pressure

• EEDM506D Temperature

Graphing Multimeter Options

The following options are available for testing:

• Dual Graphing Meter

• Volt s DC

• Volt s DC - A verage

• Volt s AC RMS

• Frequency

• Pulse Width

28

Scope Multimeter Operations Operations



:$51 ,1 *

IMPORTANT:

• Injector Pulse Width

• Duty Cycle

• Low Amps (20)

• Low Amps (40)

• Low Amps (60)

• MC Dwell (60)

• MC Dwell (90)

• 100 PSI V acuu m

• 100 PSI Pressure

• 500 PSI Pressure

• 5000 PSI Pressure

• MT5030 Vacuum

• MT5030 Pressure

• EEDM506D Temperature

• Ohms

Digital Multimeter Options

The following options are available for testing:

• Volt s DC

• Volt s DC - A verage

• Volt s AC RMS

• Ohms

• Diode/Continuity

• Low Amps (20)

• Low Amps (40)

• Low Amps (60)

6.2.2 Measurement Out of Range

A group of arrows display when a measurement is out of range for the scale se lected:

• Arrows pointing UP—measurement over maximum range

• Arrows pointing DOWN—measurement under minimum rang e

Volt age mea surements also display arrows in place of live values when the voltage exceeds the
input rating of the meter .

Risk of electrical shock.

• Do not exceed voltage limits between inputs as indicated on the rating label.

• Use extreme c aution when working with circuits that have greater than 40 volts AC or
24 volts DC.

Electrical shock can cause personal injury, equipment damage, or circuit damage.

If arrows are displayed in the live voltage values, discontinue circuit te sting.

29

Scope Multimeter Operations Operations

Correct an out-of-range condition by selecting a scale setting appro priate for th e signal be ing
sampled. See Scale‚ on page 34 for more information.

6.2.3 Scope and Multimeter Setup

The following sections explain how to adjust the scope and multimeter for the specific type of
signal being sampled. A pre-configured meter, which reduces setup time, is available for many
applications in Guided Component Tests. See Power User Tests‚ on page 19 for d et ails.

Most of the setup operations are available by selecting the Profile button on the toolbar
(Figure 6-7). Selecting the button opens the Trace Controls window at the bottom of the screen.

Figure 6-7 Sample toolbar with Profile selected

Trace Controls

The Trace Detail co ntrols are used to adjust individual characteristics of how the signal is sampled
and displayed for each channel. Availa ble options include:

• Profile—switches the waveform on and off.

• Probe—identifies the type of test probe being used.

• Peak—maximizes the signal sampling rate for capturing fast events, such as volt age spike s,

dropouts, and glitches.

• Filter—removes noise or interference from the waveform.

• Invert—switches the polarity of the displayed signal.

• Coupling AC—blocks the DC portion of an input signal in order to amplify the AC portion.

• Scale—adjusts the scale, which is the total value of the vert ical axis o f the disp lay.

• Trigger—switches triggering on or off, and sets which slope of the waveform triggers.

• Refresh—clears the digital minimum and maximum values and updates the screen.

• Sweep—adjusts the sweep, which is the total val ue of the horizon t al axis of the display.

Profile

The profile icons are used to switch the channel off and on.

Profile Icon Description

On The waveform displays for the designated channel.

Off The waveform does not display.

Tap a highlighted icon or press Y/a to switch the channel off a nd on.

30

Scope Multimeter Operations Operations

Probe

The Probe icon is used to select the type of device bein g used to sample the signal. T ypical probe
options include:

• Test Lead - Volt s DC

• Vacuum 100

• Pressure 100

• Pressure 500

• Pressure 5000

• Low Amps 20

• Low Amps 40

• Low Amps 60

• Ignition

• EEDM506D Temperature

• MT5030 Vacuum

• MT5030 Pressure

z To select a probe:

1. Select Profile from the toolbar.
The Profile information window opens.

2. Tap the Probe icon for the desired channel.
The Probe selection menu opens (Figure 6-8).

Figure 6-8 Sample probe selection menu

3. Highlight the desired probe in the menu.

4. Tap the highlighted probe to select it.

5. Tap anywhere outside the menu to close the menu window, or select Close, the last entry on
the list of probes.

31

Scope Multimeter Operations Operations

Peak

The peak icons are used to switch peak detect on and off.

Peak Icon Description

On Peak detect is active for the designated channel.

Off Peak detect is inactive for the designated channel.

With peak detect off; the scope collect s just enou gh data to plot a waveform across the screen.
This is the standard mode of operation for many scopes. With peak detect on; the scope samples
at the maximum rate possible and captures more sample po int s than needed to plot the scr een.
These additional sample points permit fast event s and glitches to be included in the wave form.

For example: with a sweep setting of 10 seconds on a screen 100 point s wide, the samp le rate
would be 10 times a second. Decreasing the sweep to 1 second, increases the sample rate to 100
times a second. Now , a fast occurr ing event is likely to be captured due to the increased rate.

Peak detect puts the scope in a high speed sampling mode, which under cer t ain cir cumst ances
may result in unwanted noise from components such as injectors and sole noids bein g picked up
and displayed. Therefore, there are times when peak d etect should not be use d beca use the
waveform may be distorted or hard to read due to noise.

An example of when not to use peak detect would be when sampling an oxygen (O2) sensor
signal. An O2 sensor signal is relatively slow and requires a clean, noise-free pattern for an
accurate diagnosis. If peak detect is on, more noise is picked up making diagnosis difficult.

Filter

The filter icons are used to switch filtering, which removes noise and other interference from the
waveform, on and off.

Filter Icon Description

On

Off

Unwanted interference has been removed from the
waveform displayed for the designated channel.

Any signal interference on the sampled circuit is included
in the waveform displayed for the designated channel.

32

Scope Multimeter Operations Operations

The filter works slightly different depending upon what type of te st is being condu cted:

• For a direct measurement test, such as volts, amp s, or pressure , the filter min imizes the

display of very fast spikes by averaging the sampled data when filter is active.

• For a calculated measurement test, such as frequency, pulse wid th, dwell, or duty cycle,

extremely fast spikes (20 uS and faster) from sources like the ignition system are ignored
when filter is active.

An example of when to use Filter would be for testing an O2 sens or using a 1 or 2 volt scale.
Filter smooths out spikes and fast variations in the waveform. The Filter setting is most useful

when working with scales of 5 volts and below. The lower the volts scale, the more likely noise
could be an issue.

Filter is also beneficial for low amp probe testing. Due to the conversion factors used by the probe,
a very low volts scale is used to measure the output of the probe. For a probe with a conversion
factor of 100 mV/A connected to a 2 amp load, the scope uses a 200 mV scale to mea sure th e
output of the probe. The scope converts th e measured output to 2 amps for disp lay on the screen.

Invert

The Invert setting is used to switch the polarity of the waveform on the screen . For example; invert
the signal of square waveform that rises from 0 volt to 5 volt s and the display would sho w a
waveform that falls from 0 volt to –5 volts.

An icon displays when the waveform on the screen has been inverted:

Invert Icon Description

On

Off

The polarity of the waveform being displayed is inverted
for the designated channel.

The waveform is being displayed normally for the
designated channel.

Coupling AC

Coupling AC subtracts the average value of a signal so that small variations display on the
waveform. This is done by blocking the direct current (DC) portions of a signal in order to disp lay
only the alternating current (AC) portions of the signal without driving the waveform off of the
viewing area of the screen.

33

Scope Multimeter Operations Operations

An icon displays when Coupling AC is active:

Coupling AC Icon Description

On

Off

The DC portion of the waveform is blocked for the
designated channel.

The DC portion of the waveform is NOT blocked for the
designated channel.

This option is ideal for viewing items such as alternator ripple or fuel pump amper age.

Scale

The Scale setting adjusts the vertical, or y axis, value of what displays on the screen. The value
shown in the Profile information panel represents the entire height of the display area for that
channel. Scales can be set independently for each channel.

z To adjust the scale:

1. Select Profile from the Scope Multimeter toolbar.
The Profile information window opens.

2. Tap the Scale value for the channel you wish to adjust.
The Scale menu opens (Figure 6-9).

Figure 6-9 Sample Scale menu

3. Highlight the desired scale in the menu.

4. Tap the highlighted scale to select it.

5. Tap anywhere outside the menu, or select Close, to close the menu window.

34

Scope Multimeter Operations Operations

Trigger

Triggering allows you to set the Scope M ultimeter so that it be gins disp laying a wavefor m once
predetermined signal conditions, or triggers, are met. Triggering produces a much more stable
waveform. The waveform is anchored at the trigg er point, so the ima ge does not appear to flicker
or drift as it updates. A trigger can only be set for one channel with a 2-cha nnel setup.

The trigger point is indicated by a plus sign (+) on the scope grid. The plu s sign can be d ragged
across the screen to roughly position it. Use the Trigger Controls, available by selecting the large
plus (+) sign at the base of the screen, to accurately adjust the trigger position. Y ou can choose
which slope of the waveform to trigger on using the Profile controls.

z To set a trigger:

1. Select Profile from the Scope Multimeter toolbar.
The Profile information window opens.

2. Tap the Trigger icon for the channel you want the trigger set to.
Each tap of the icon moves you progressively through the three st ates of trig gering; ri sing,

falling, and off.
Tapping the icon moves you sequentially through the three available settings:

Trigger Icon Description

The waveform for the designated channel is anchored at

Rising

Falling

Off There is no trigger set for the designated channel.

the point voltage rises to the threshold value, shown as a
plus sign (+) in the main body of the screen.

The waveform for the designated channel is anchored at
the point voltage falls to the threshold value, shown as a
plus sign (+) in the main body of the screen.

3. Once the slope is determined, tap the plus sign (+) at the botto m of the inform ation window.
The trigger adjustment controls open (Figure 6-10).

35

Scope Multimeter Operations Operations

Figure 6-10 Sample Trigger controls

4. Tap the arrowheads on the screen, or use the keyp ad to mo ve the trig ger in to position. A
digital readout centered between the arr owheads gives the prec ise position of th e trigger.

5. Select Profile from the toolbar, or press the N/X key, to exit.

Refresh

Selecting Refresh from the Profile window clears the minimum and maximum digital values for
both waveforms and updates the viewing screen. These digital values, wh ich display to the right
of the Refresh icon, are the highest and lowest va lue recorde d for each wavefo rm since th e test
was activated, or from the last time Refresh was selected.

Sweep

Sweep is the amount of time represented by the screen, or the horizontal scale of the display.
Setting sweep adjusts the x axis of the display screen. Sweep can be adjus ted in increm ent s
ranging from 5 microseconds to 5 minutes. The value on the bottom line of the Profile information
panel indicates the sweep setting for both channels. Sweep applies to the entire meter and cannot
be set independently for the two channels.

z To adjust the sweep:

1. Select Profile from the Scope Multimeter toolbar.
The Profile information window opens.

2. Tap the Sweep value on the bottom line of the Profile information panel.
The Sweep menu opens (Figure 6-11).

36

Scope Multimeter Operations Operations

Figure 6-11 Sample Sweep menu

3. Scroll to highlight the desired sweep value in the menu.

4. Tap the sweep to select it.

5. Tap anywhere outside the menu, or select Close, to close the menu window.

Cursors

Selecting the Cursor button on the Scope Multimeter toolbar places two vertical rules on the
screen that can be repositioned to measure amplitude, time and the delta , or difference, betwee n
the two (Figure 6-12). Values display in the Pro file area at he base of the display screen .

Figure 6-12 Sample cursor display

37

Scope Multimeter Operations Operations

z To reposition the cursors:

1. Tap the Cursor button on the toolbar to activate cursors.

2. Touch and drag the numbered recta ngle in the swee p area of the display to move that cursor
to where you want it.

3. Touch and drag to move the other cursor.

4. Tap the Cursor button to cancel the cursors.

38

Chapter 7 Previous Vehicles and Dat a

The Previous Ve hicles and Dat a Home scre en selection allows you to quickly configure the
diagnostic tool to the identity of a recently tested vehicle, and to access saved dat a files. A menu
of options opens when Previous Vehicles and Data is selected:

• Vehicle History

• View Saved Data‚ on page 40

• Delete Saved Data‚ on page 40

7.1 Vehicle History

The tool stores the identification of the last twenty-five vehicles tested. The ol dest vehicle r ecord
is deleted when a new vehicle is identified once th ere a re twenty-five vehicles on file .

Figure 7-1 Sample vehicle history list

z To select from the vehicle History:

1. Select Previous V ehicles and Da ta from the Home screen.

2. Select Vehicle His tory from the m enu.
A list of up to 25 previously tested vehicles displays. Each vehicle is given a unique file name.

Scroll to view the entire list.

3. With the vehicle to be opened highlighted, either t ap the vehicle ID or pr ess the Y/a key.
The appropriate software loads a nd a vehi cle ID confirmation screen displays.

4. Select OK or press Y/a to continue.
The System Menu for the selected vehicle displays.

39

Previous Vehicles and Data View Saved Data

NOTE:

7.2 View Saved Dat a

Selecting the View Saved Data menu option opens a list of all the data movies and screen images
that are stored in memory. Saved files are listed in chronological order by the date and time that
they were created with the most recent files are at the top of the list.

Figure 7-2 Sample saved data list

Saved files can either be opened directly on the diagnostic too l, or downloade d to a persona l
computer and opened using ShopStream Connect.

z To review a saved file:

1. Select Previous V ehicles and Da ta from the Home screen.

2. Select View Saved Dat a from the menu.

3. Select a file to review from the list.

7.3 Delete Saved Data

This menu option is used to permanently erase sa ved files fro m memory.

z To delete a saved file:

1. Select Previous V ehicles and Da ta from the Home screen.

2. Select Delete Saved Data from the menu.
A list of saved files displays.

i The Select All/Deselect All and Delete buttons become available on the toolbar so that you can

either delete individual files or clear the entire memor y buf fer all at once.

3. Select a file from the list and a confirmation message displays.

4. Select an option from the confirmation message:

40

Previous Vehicles and Data Delete Saved Data

– OK—deletes the selected file and returns to the saved files list, which no longer includes

the deleted file.

– Cancel—returns to the saved files list without deleting the selected file.

5. Select Back on the toolbar to return to the Pre vious V ehicles and Data menu, select Home to
return to the Home screen.

41

Chapter 8 Tools

The Tools option on the home screen is used to configure the diagnostic tool for your personal
preferences. T ap the Tools button to open a menu of options.

8.1 Tools Menu

The following options are available from the Tools menu:

• Connect-to-PC—use to transfer and share files with a personal computer (PC).

• Configure Shortcut Key‚ on page 43—use to chan ge the fu nction of the shortcu t key.

• System Information‚ on page 43—use to view configuration informatio n for the diagnostic tool.

• Settings‚ on page 44—use to configure cert ain ch aracte ristics of the diagno stic tool.

8.1.1 Connect-to-PC

Connect-to-PC allows you to network your diagnostic tool to a person al computer to access,

transfer, a nd manage the saved files on the tool.
The optional ShopStr eam Connect™ sof tware , which lets you view data files on a personal

computer, tr ansfer files between the tool and PC, and d ownload software updates fro m the PC to
the tool, offers an ideal way to manage saved dat a files. ShopStream Connect is a free software
program that can be downloaded online. For website information, se e the we bsites listed on the
inside cover of this manual.

Figure 8-1 Sample Tools menu

z To connect the diagnostic tool to a PC:

1. Select Tools from the Home screen to open the menu.

2. Select Connect-to-PC from the Tools and Setup menu.

42

Tools T ool s Menu

3. Follow the instructions on the screen to complete the operation.

A USB cable, supplied with your diagnostic tool, is used to link the tool to the PC. When the tool is
connected to the PC a communications icon appears on the right edge of the title bar.

8.1.2 Configure Shortcut Key

This feature allows you to change the function of the Shortcut key. Options ar e:

• Brightness—opens the brightness setting screen.

• Save Screen—saves a bitmap image of the visible screen.

• Save Movie—saves a recording of the data buffered in tool memory.

• Show Shortcut Menu—opens the menu so you can quickly select from any of the functions.

• T oggle Re cord/Pa use—programs th e Shortcut key to work as the Pa use and Play butto ns.

z To assign a funct ion to the Shortcut key:

1. Select Tools from the Home screen.
The Tools menu opens.

2. Select Configure Shortcut Key from the menu.

3. Select a function from the menu.

4. Select Back on the toolbar or press the N/X key to return to the options menu.

8.1.3 System Information

The System Information option lets you view configuration information for your diagnostic tool.

Figure 8-2 Sample system information screen

z To display the System information scr een:

1. Select Tools from the Home screen to open the menu.

2. Select System Information from the menu.

43

Tools T ool s Menu

The System Information screen displays.

3. Scroll as needed to view all of the data.

4. Select Back on the toolbar or press the N/X key to return to the options menu.

8.1.4 Settings

Settings allows you to adjust certain basic diagnostic tool functions to your personal preferen ces.
Selecting opens an additional menu that offe rs the following:

• System Settings‚ on page 44

• Configure Scope/Meter‚ on page 48

• Configure Units‚ on page 50

System Settings

Selecting System Settings opens a menu with two options; Display and Date & Time. Either
selection opens an additional menu.

Display options include:

• Brightness‚ on page 44—adjust s the intensity of the screen back lighting.

• Color Theme‚ on page 45—changes the ba ckground color of the scre en disp lay.

• High Contrast Toolbar‚ on page 46—enhances toolbar graphics for poor lighting conditions.

• Font Type‚ on p a ge 46—switches between standard and bold text for better visibility.

• Backlight Time‚ on page 46—adjusts how long the screen stays on with an idle unit.

• Touch Calibration‚ on page 46—calibrates the touch screen display.

Date & Time options include:

• Time Zone‚ on page 47—sets the intern al clock to th e local tim e st andar d.

• Clock Settings‚ on page 47—sets the time on th e intern al clock.

• Daylight Savings Time‚ on page 48—configur es the clock for Daylig ht Savings Time.

• Time Format‚ on p age 48—switches the time displays between a 12 or 24 hour clock.

• Date Format‚ on page 48—configures how the mon th, date, an d year di splays.

Brightness

Selecting this option opens the brightness setting screen for a djusting the ba ck lighting of th e
display (Figure 8-3).

44

Tools T ool s Menu

Figure 8-3 Sample brightness setting screen

Each tap of the Plus and Minus buttons, or the up (b) and down (d) arrows, incrementally
changes the back lighting up or down respectively.

Select Back from the toolbar or press the N/X key to exit.

Color Theme

This option allows you to select between a white and black background for the screen. The black
background can be beneficial when working under poor lighting conditions.

Selecting opens a menu with two choices: Day Theme (white background) and Night Theme
(black background). Make a selection and a “please wait” message momentarily displays followed
by the Home screen. The new toolbar setting is now active.

Figure 8-4 Sample Night Theme menu screen

45

Tools T ool s Menu

IMPORTANT:

High Contrast Toolbar

This option allows you to switch to a high contrast toolbar. This toolbar features black and white
buttons with crisp graphics that are easier to see in poor lighting conditions or bright sunlight.

Selecting opens a menu with two choices; Color Toolbar and High Contr ast Toolbar . Select and a
“please wait” message displays followed by the Home screen. The new setting is now active.

Font Type

This option allows you to select between standard and bold faced type for the display screen. Bold
type makes screen writing more legible under poor lighting or bright sunlight cond itions.

Selecting opens a menu with two choices: Normal Font and Bold Font. Tap a menu item, or scr oll
with the keypad and Press Y/a, to make a selection. The change is inst a nt aneo us. Select the
Back or Home button on the toolbar to return to either the Settings menu or the Home screen .

Backlight Time

This option allows you to configure how long the screen backlight remains on when the tool i s
inactive. The following choices are available:

• Always On

• 15 Seconds

• 30 Seconds

• 45 Seconds

• 60 Seconds

Tap the menu item desired, or scroll with the keypad and Press Y/a, to make a selection. Select
Back or Home on the toolbar to return to either the Settings menu or the Home screen.

Touch Calibration

Calibrating the touch screen maintains the accuracy of the touch-sensitive display . Perform the
following procedure on a routine basis to keep your diagnostic tool in good wo rking or der.

z To calibrate the touch screen:

1. Select Tools from the Home screen to open the menu.

2. Select Settings from the menu.

3. Select Touch Calibration from the menu.
The calibration screen opens (Figure 8-5).

It is critical to complete the touch screen calibration sequence once it has begun. Never power
down the unit while a screen calibration is in process, serious damage to the unit may result.

4. Touch each box on the screen as it displays.
The display returns to the Settings menu once the screen calibration procedure is comple te.

46

Tools T ool s Menu

:$51,1*'RQRWSRZHUWKHWRRORIIXQWLOWKH7RXFK

&DOLEUDWLRQKDVEHHQFRPSOHWHGVXFFHVVIXOO\

728&+6&5((1&$/,%5$7,21

728&+%2;,1833(5/()7&251(5

Figure 8-5 Sample calibration screen

Time Zone

This option opens a menu of time zone settings. Scroll to highlight, then select the local time zone.
The display returns to the Settings menu once a time zone is selecte d.

Clock Settings

This option opens a window for resetting the time on the real-time clock.

z To set the clock:

1. Select Tools from the Home screen to open the menu.

2. Select Settings from the menu.

3. Select Clock Settings from the menu to open the Clock Settings screen (Figure 8-6).

Figure 8-6 Sample Clock Settings screen

47

Tools T ool s Menu

4. Tap the up (+) button on the screen or press the up (b) key on the keypad to incrementally
increase the number in the highlighted fie ld. Tap the down (–) button on the screen or press
down (d) on the keypad to incrementally decrease th e number.

5. Tap the check (a) button on the screen or press the Y/a key on the keypad to move the
highlight to the next field.

6. Repeat Step 4 and Step 5 until the correct time is displayed.

7. Tap the Back on the toolbar or press the Y/a on the keypad to close the Clock Settings
window and return to the Settings menu.

Daylight Savings Time

This option opens a menu to configure the intern al clock for Daylight Savings T ime. Choose fr om:

• ON—sets the clock for Daylight Savings time.

• OFF—sets the clock for standard time.

Make either selection, then tap the Back button or press the N/X key to return to th e menu .

Time Format

This option determines whether time is displayed on a 12 or 24 h our clock. Sel ecting open s a
menu with two choices:

• 24 Hour Format

• 12 Hour Format

Make either selection, then tap the Back button or press the N/X key to return to th e menu .

Date Format

This option allows you to select how date information is displayed. Select from:

• (MM_DD_YYYY)—Month, Day, Year

• (DD_MM_YYYY)—Day , Month, Year

• (YYYY_MM_DD)—Year, Month, Day

Make a selection, then tap the Back button or press the N/X key to return to the me nu .

Configure Scope/Meter

This option allows you to customize certai n character istics of the di splay scree n when using th e
Scope Multimeter module. Selecting opens a menu with the followin g options:

• Trigger Mode‚ on page 48

• Display‚ on page 49

• Divisions‚ on page 49

Trigger Mode

Configure Scope/Meter allows you to choose the type of trigger, see Trigger‚ on page 35 for
additional information. T wo tr iggerin g choice s are availa ble:

• Auto Trigger—updates the screen when the signal cr osses the trig ger threshol d in the

selected direction (rising or falling).

48

Tools T ool s Menu

The screen automatically updates after a shor t period so you can se e the wa veform , even if
the signal does not cross the trigger threshold. You can set a threshold to optimize viewing.

• Manual T rigger—up dates the scr een when the signal cro sses the trigg er thre shold in the

selected direction (rising or falling).
The screen does not update if the signal does not cross the trig ger threshold. Y ou can captu re

intermittent events because the screen only upda tes when the signal cr osses the trigger
threshold.

Select a menu item, then tap Back or press the N/X to return to the Configure Scope/Meter menu.

Display

This option switches a grid pattern on the meter screen on an d of f.

Figure 8-7 Sample Scope multimeter screen grid

z To switch the Display:

1. Select Tools from the Home screen.

2. Select Settings from the Tools and Setup menu.

3. Select Configure Scope/Meter from the Settings menu.

4. Select Display from the menu.

5. Highlight either menu entry to make a selection:

– Show Grid—to switch the grid lines on.
– Hide Grid—to switch the grid lines off.

6. Tap the Back button or press the N/X key to return to the Settings menu.

Divisions

The option allows you to switch between Full Scale or Per Division settin gs for the trace setup and
the display settings. Full Scale configures the meter so one division, or unit, is th e full viewing area
of the screen. Per Division adjusts a single unit, or division, to one tenth o f the scree n.

49

Tools T ool s Menu

Figure 8-8 Sample Scope Multimeter screen set to Per Division

z To switch the divisions:

1. Select Tools from the Home screen.

2. Select Settings from the Tools and Setup menu.

3. Select Configure Scope/Meter from the Settings menu.

4. Select Divisions from the menu:
a. Highlight either menu entry to make a selection:

– Trace Settings—to change the Scale menu selections from Full scale (20V) to

Per division values (2.0 V/Div).

– Display Settings—to change the value of the scale selected, which is displayed in the

profile area, from Full scale (20V) to Per division values (2.0 V/Div).

b. Select from the menu:

– Full Scale—one unit per screen.
– Per Division—ten units per screen.

c. Tap the Back button or press the N/X key twice to return to the menu.
d. Select Trace Settings or Display Settings, and repeat Step 4 if needed.

5. Tap the Back button or press the N/X key to return to the Settings menu.

Configure Units

Selecting opens a dialog box that allows you to choose between US customary or metric units of
measure for temperature, vacuum, and pressure.

50

Tools T ool s Menu

Figure 8-9 Sample Configure Units menu

z To change the units setup:

1. Select Tools from the Home screen to open the menu.

2. Select Configure Units to open the me nu.

3. Select an item from the Configure Units menu.

– Temperature
– Vacuum
– Pressure

4. Select a setting from the listed choices.

5. Select Back on the toolbar or press the N/X key to return to the options menu.

51

Chapter 9 Maintenance

IMPORTANT:

IMPORTANT:



:$51 ,1 *



:$51 ,1 *

This chapter covers how to care for your diagnostic tool.

9.1 Cleaning and Inspecting the Diagnostic Tool

When using the diagnostic tool perform the following tasks to keep it in top shape:

• Check the housing, wiring, and connectors for dirt and damage befor e and a f ter each use .

• At the end of each work day, wipe the diagnostic tool housing, wiring, and connectors clean

with a damp cloth.

Do not use any abrasive cleansers or automotive chemicals on the unit.

9.1.1 Cleaning the Touch Screen

The touch screen can be cleaned with a soft clo th and a m ild window clean er.

Do not use any abrasive cleansers or automotive chemicals on the touch screen.

9.2 Battery Service

Follow all safety guidelines when handling the battery pack.

Risk of electric shock.

• Prior to rec ycling the battery pack, protect exposed terminals with heavy insulating t ape
to prevent shorting.

• Disconnec t all test leads and turn diagnostic tools off before removing the ba ttery pack.

• Do not attempt to disassemble the battery pack or remove any component projecting
from or protecting the battery terminals.

• Do not expose the unit or battery pack to rain, snow, or wet conditions.

• Do not short circuit the battery terminals.

Electric shock can cause injury.

Risk of explosion.

• Use the proper factory battery pack only, incorrect replacement or tampering with the
battery pack may cause an explosion.

Explosion can cause death or serious injury.

52

Maintenance Battery Service

IMPORTANT:

NOTE:

IMPORTANT:

9.2.1 Battery Safety Guidelines

The battery pack contains no user serviceable components. Tampering with the battery pack
terminals or housing will void the product warranty.

Keep the following in mind when using and handling the battery p ack:

• Do not short circuit battery terminals.

• Do not immerse the diagnostic tool or battery pack in water , or allow water to enter the un it or

battery compartment.

• Do not crush, disassemble, or tamper with the battery pack.

• Do not heat the battery pack to over 100°C (212°F), or dispose of it in a fir e.

• Do not expose the battery pack to excessive physical shock or vibration.

• Keep the battery pack out of the reach of children.

• Do not use a battery pack that appears to have suffered abuse o r damage .

• Store the battery p ack in a cool, dry, well ventilated area.

i The battery pack should be used within a short period of time (about 30 days) after cha rging to

prevent loss of capacity due to self-discharging.

If long-term storage of the battery pack is necessary, it should be stored in a cool, dry , well
ventilated place with a 30 to 75 percent state of char ge to prevent loss of char acteristics.

T o prolong the life of your ba ttery , power off the unit when not in use. The diagnostic tool has a built
in charger that recharges the battery on demand wheneve r it is connecte d to a power sou rce.

9.2.2 Replacing the Battery Pack

If the battery pack no longer holds a charge, contact your sales represent ative to order a new one.

Replace the battery pack with original Snap-on replacement p arts only.

z To replace the battery pack:

1. Loosen the two captive screws that retain the battery compartment cover on the back-side of
the diagnostic tool.

2. Pull up on the inner edge of the battery compartmen t cover to relea se it, pivo t the cover into
an upright position, then lift the battery cover off of the housing.

3. Slide the battery down to disengage the electrical cont act s.

4. Remove the battery from the tool housing.

5. Align the tabs on the sides of the battery compartment with the slots on the new battery , then
place the battery into the housing.

6. Slide the battery up to engage the electrical contact s and snap it into pla ce.

7. Fit the battery cover onto on the housing, then pivot the cover down so that it snaps into pl ace.

8. Snug up the captive screws to hold the cover in place. Do not overtighten the screws!

53

Maintenance Battery Service

NOTE:

 

1— Battery
2— Battery Cover
3— Captive Screws

Figure 9-1 Battery pack replacement

9.2.3 Disposing of the Batteries

Always dispose of the battery pack according to local regulations, which vary for dif fer ent
countries and regions. The battery pack, while non-h azardous waste, does contain recyclable
materials. If shipping is required, ship the battery pack to a recycling facility in accordance with
local, national, and international regulations. For additional information contact:

• North America—Rechargeable Battery Recycling Corporation (RBRC) at http://www .rb rc.org

or http://www.call2re cycle.org, or call 1( 800) 822 -8837 (USA)

• United Kingdom—Electrical Waste Recycling Company at http://www.electricalwaste.com

Products bearing the WEEE logo (Figure9-2) are subject to European Union regulations.

Figure 9-2 sample WEEE logo

i Always dispose of materials according to local regulations.

Contact your sales representative for details.

54

Index

A

AC/DC power supply 9
Accept key 8
Alligator clips 26
amp probe 27
Arrow keys 8

B

Battery 9

Disposal 54
Handling 53
Recycling 54
Replacing 53

Specifications 7
Battery replacement 52
Battery service 52
Brightness, adjusting 44
Buttons

Control 8

Toolbar, Guided Component Tests 15

Toolbar, Scope Multimeter 15

–9

–54

C

Cables

channel 1 26

channel 2 26

secondary coil adapter 27

secondary ignition clip-on wire adapter 27
Cancel key 8
Capabilities, scope multimeter 24
Cleaning 5 2
Component information 20
Configure units 50
Confirmation messages 13
Connect-to-PC 42
Current Probe 27

–51

–21

D

Dimensions, unit 7
Directional buttons 8
Display screen, specifications 7

E

Emergency shutdown 12
Error messages 13

F

Features & Benefits 19
Functional description 5

–6

G

Guided Component Tests 17–23

operations 20
vehicle identification 17

–23

–18

H

Home screen 10–12
Home screen buttons 11
How To... 19

M

Main body

Guided Component Tests 16
Scope Multimeter 16

Manual conventions

Description 3
Notes 4

Messages

Safety iii
Screen 13

Meter capabilities 24

–iv

O

Operating temperature 7
Options

digital multimeter 29
graphing meter 28
scope multimeter 28

P

Power key 9
Power sources 9

AC/DC power supply 9
Power User Tests 19
Powering on 10

R

Refresh 36

S

Safety iii–iv

55

Index

Saved data 39–41
Saved vehicle data 40
Scanner

Title bar 10

Scope Multimeter

configuring 28
cursors 37
leads 26
operations 28

–27

–38

setup 30
sweep controls 36
Trace Details 30
traces 30

Screen layout

Guided Component Tests 14
Scope Multimeter 14

–16

Screen messages 13
Secondary coil adapter 27
Shortcut button

Configuring 43
Shortcut key 9
Specifications 7
Stand, the 9
Storage temperature 7
System Information 43

–44

–16

T

Temperature

Operating 7

Storage 7
Test leads 26

–27

Tests

Component 21
Time settings 47
Title bar 10
Tool settings 44
Tool setup options 42

–23

–48

–11

–46

–51

Toolbar

Guided Component Tests 14

Scope Multimeter 14

–16

–16

Touch Screen

Calibrating 46

viewing options 46
Touch screen calibration 52
Trace Controls, scope 30

V

Vehicle history 39
Viewing component information 20

W

Warning messages 13
Weight, unit 7

56