Sloan EAF-700-LT Installation Manual

INSTALLATION INSTRUCTIONS AND USER MANUAL FOR

SLOAN

EAF-700

AC Powered, Sensor Activated Electronic
Gooseneck Hand Washing Faucets

EAF-750

Battery Powered, Sensor Activated Electronic
Gooseneck Hand Washing Faucets

®

EAF GOOSENECK SERIES FAUCETS

Code No: 0816409

Rev. 1 (07/11)

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants its product, manufactured and sold for commercial for industrial uses, to be free from defects in material and
workmanship for a period of three (3) years (one (1) year for special nishes, SF faucets, PWT electronics and 30 days for PWT software) from date of rst purchase.
During this period, Sloan Valve Compnay will, at its option repair replace, or refund the purchase price of any product which fails to conform with this warranty under
normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No
claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES
OF ANY MEASURE WHATSOEVER.

PRIOR TO INSTALLATION

Prior to installing the Sloan Optima EAF-700 Series Faucets,
install the items listed below. Also, refer to rough-in illustrations.

• Lavatory/sink

• Drain Line

• Hot/Cold Water Supply Lines or Tempered Supply

IMPORTANT:

• ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH
APPLICABLE CODES AND REGULATIONS.

• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT
COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON
COMPRESSION FITTINGS.

Trim Plates

When the EAF Faucet is installed on a sink that has three (3) hole
punchings, a trim plate should be used. Trim Plates must be specied and
ordered separately.
SFP-11 Trim Plate for 4” (102 mm) Centerset Sink
SFP-22 Trim Plate for 8” (203 mm) Centerset Sink

TOOLS REQUIRED FOR INSTALLATION

• 13 mm open end wrench or nut driver for faucet retainer nut • 5/8” open end wrench for female end of ex hose

1

FAUCET ROUGH-IN

24°

5-7/8”

(

147 mm)

2-1/4” (57 mm)

2-9/16”

(65 mm)

5-11/32”

(151 mm)

3-15/16”

(100 mm)

10-1/32”

(255 mm)

24°

5-7/8”

(147 mm)

SPOUT

O-RING

MIXING LEVER

(CAN BE SET AND

REMOVED)

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK
THICKNESS

NUT

RETAINER

GASKET

HOT

SUPPLY

COLD

SUPPLY

13” (330 mm)

LONG FLEX HOSE

2-1/4” (57 mm)

2-9/16”

(65 mm)

TEMPERED

SUPPLY

SPOUT

O-RING

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

13” (330 mm)

LONG FLEX HOSE

5-11/32”

(151 mm)

3-15/16”

(100 mm)

10-1/32”

(255 mm)

24°

5-7/8”

(

147 mm)

S

POUT

O-RING

MIXING LEVER

(CAN BE SET AND

REMOVED)

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK
THICKNESS

NUT

RETAINER

GASKET

HOT

SUPPLY

COLD

SUPPLY

13” (330 mm)

LONG FLEX HOSE

2-1/4” (57 mm)

2-9/16”

(

65 mm)

5-11/32”

(

151 mm)

3-15/16”

(

100 mm)

10-1/32”

(255 mm)

Model EAF-700/750

1.5 gpm (5.7 Lpm) Max. Flow†

Faucets with Tempered Water Supply

Model EAF-700/750

.5 gpm (5.7 Lpm) Max. Flow†

1

Faucets with Hot/Cold Water Supply

If a connection to separate
hot and cold water supplies
is desired, then a Bak-Chek
tee tting (not supplied) must
be used prior to connecting
to the faucet.

1 - INSTALLATION TO DECK

IMPORTANT: FLUSH DIRT, DEBRIS, AND SEDIMENT FROM SUPPLY LINE(S)
BEFORE CONNECTING FLEX HOSE(S).

A

Remove nut, faucet retainer and gasket.

Install faucet into the center hole in deck or lavatory – 1-3/16”

B

(30 mm) minimum hole required.

NOTE:

If installing the faucet on a three (3) hole sink, a trim plate

should be installed at this time.

®

† EAF Faucets are furnished with a 1.5 gpm (3.8 Lpm) spray head).

2

When the EAF faucet is installed on a sink that has three
(3) hole punchings, a trim plate should be used.

must be specied and ordered separately:
ETF-312-A

Trim Plate for 4” (102 mm) Centerset Sink

ETF-510-A

Trim Plate for 8” (204 mm) Centerset Sink

Trim plate

6”

(152 mm)

CABLE

LENGTH

FROM FAUCET

BATTERY

PACK

Ø 2-13/32”

(61 mm)

2 - CONNECTION TO WATER SUPPLY

A

Flush supply stops before making connections.

B

Install strainer and ex hose onto supply stop.

3A -

EAF-700 MODELS

– PLUG ADAPTER INTO RECEPTACLE

Tighten the ex hose (with strainer in place) securely to the

C

supply.

pen supply stop(s).

O

D

ELECTRICAL CONNECTION FOR UP TO SIX (6) FAUCETS

USING ONE ADAPTER

6 VDC
PLUG-IN
ADAPTER

3B -

EAF-750 MODELS

– CONNECT BATTERY PACK

LIMIT ONE FAUCET PER BATTERY PACK

3

POWER SPLITTER
ELECTRICAL CABLE

POWER SPLITTER
ELECTRICAL CABLE

TO ADDITIONAL
FAUCETS
(6 MAX.)

4 - START-UP

1x

7

7

A

Remove label from faucet sensor.

B

Activate faucet by pressing the button one (1) time, then
immediately step away.
Faucet will run water for 4 seconds. Wait 10 seconds and then the
faucet is ready to use.

SET AND FIX TEMPERATURE (OPTIONAL)

A

B

C

4

HOT LIMIT STOP ADJUSTMENT

LIMIT THE MAXIMUM WATER TEMPERATURE. NOTE: THIS DOES NOT TAKE THE PLACE OF AN ASSE 1070 CERTIFIED MIXING DEVICE. BUT IS AN ADDED
MEASURE TO LIMIT DELIVERY OF HOT WATER.

A

B

D

E

C

5

SENSOR RANGE ADJUSTMENT

5 Sec.

2x +

1x5 Sec.

1x

2x

8x

7x

FACTORY DEFAULT = 6

1 x ( 1x, 2x,...,5x)

4x

FACTORY SETTING IS APPROPRIATE FOR THE MAJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING UNLESS UNDER EXTREME SITUATIONS.

A

B

D

E

C

F

G

6

12/24 LINE PURGE FEATURE

1x 24 sec

h

DEACTIVATE

ACTIVATE 2x

1x

3x

12h

---

24h

1 x

2 min.

OR

1 x 2 Sec.

1 x

2 min.

OR

1 x

1 x

2 min.

OR

OR

2 min.

1 x

1 x

2 x

2 min.

OR

OR

1 x 2 Sec.

2 min.

1 x 6 Sec.

1 x

1 x 0-5 Sec.

1x

1 x 0-5 Sec.

1x

1x

I.Q.-CLICK FEATURE

I. CONTINUOUS RUN

A

Continuous run of water for
2 minutes.

This feature will operate the faucet every

2 or 24 hours since last use, if not used

1
to prevent stagnant water conditions.

efault purge duration is two minutes.

D

Consult factory regarding other timing

ptions.

o

B

Faucet will operate normally after 2 minutes or after pressing
i.q.-click button once.

II. CLEANING MODE

A

OFF-DELAY (FOLLOW UP TIME)

DURATION OF TIME THE WATER RUNS AFTER TARGET IS REMOVED.

A

B

Pause faucet for cleaning for
2 minutes.

Press the button for
approximately six (6)
seconds. Release.

Press again (water
ows) and release
when the desired
time of water ow
(0-5 seconds) is
reached.

B

Faucet will operate normally after 2 minutes or after pressing
i.q.-click button once.

C

Sensor will ash once
and then the faucet is
ready to operate.

7

OPERATION

0 V 6 V

1x

0 V 6 V

0 V 6 V

s the user’s hands enter the beam’s effective range, the beam is reected

A
back into the sensor receiver and activates the solenoid valve allowing
water to ow from the faucet. Water will ow until the hands of the user
are removed or until the faucet reaches its automatic time out limit setting.

BATTERY REPLACEMENT

NOTE: REPLACE BATTERY WHEN RED LED INDICATOR FLASHES EACH TIME FAUCET IS IN USE OR WHEN FAUCET STOPS FUNCTIONING.

A

No need to turn
off water.

Loosen screw

B

with hex wrench
and remove cap.
Slide cover
forward and lift
off.

Remove battery.

C

Replace batteries
with new “CR-P2”
lithium battery.

Activate faucet

E

by pressing i.q.
cliq one (1) time,
then immediately
step away.

Faucet will

F

operate for 4
seconds.

Replace cover.

D

Wait 10 seconds

G

and then the
faucet is ready
for operation.

8

TECHNICAL DATA

NOMINAL VOLTAGE

POWER SUPPLY

WATER PRESSURE

FLOW RATE

WATER FLOW DURATION

WATER TEMPERATURE

6 VDC

120 VAC/ 6.75 VDC

4.3-125 PSI (0.3 - 8.6 bar)

1.5 gpm (5.7 Lpm)

0.5-4 seconds

MAX. 176°F/80°C

TROUBLESHOOTING

1. Faucet does not function.

A. Adhesive packaging label afxed over sensor eye.

Remove adhesive label from sensor eye.

B. “Intermittent Off” is activated.

Press button once.

C. Water supply stop(s) closed.

Open water supply stop(s).

D. Battery is “dead”.

Replace battery (refer to Battery Replacement section of guide).

2. Faucet delivers water in an uncontrolled manner.

A. Reection.

Remove reective surface.

B. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

3. Faucet does not deliver any water when Sensor is activated.

Solenoid Valve produces an audible “CLICK.”

A. Water supply stop(s) closed.

Open water supply stop(s).

B. Water supply stop strainer(s) clogged.

Remove, clean, and reinstall water supply stop strainer(s). Replace
strainer(s), if required.

Solenoid Valve DOES NOT produce an audible “CLICK.”

A. Battery low (battery operated models).

Replace battery (refer to Battery Replacement section of guide).

B. Power failure.

Check power supply.

4. Faucet delivers only a slow ow or dribble when sensor is activated.

A. Water supply stop(s) are partially closed.

Completely open water supply stop(s).

B. Water supply stop strainer(s) clogged.

Remove, clean, and reinstall water supply stop strainer(s). Replace
strainer(s), if required.

C. Spray head is clogged.

Remove, clean, and reinstall spray head. Replace spray head,
if required.

D. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

5. Faucet does not stop delivering water or contrinues to drip after user is
no longer detected.

A. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

6. LED indicator blinks when faucet is in use.

A. Battery low (battery operated models).

Replace battery (refer to Battery Replacement section of guide).

7. The water temperature is too hot or too cold on a faucet connected to
hot and cold supply lines.

A. Supply stops are not adjusted properly.

Adjust supply stops.

When assistance is required, please contact Sloan’s

Installation Engineering Department at:

1-888-SLOAN-14 (1-888-756-2614)

CARE AND CLEANING

DO NOT USE

clean faucets that may dull the luster and attack the chrome or special
decorative nishes. Use
clean cloth or towel. While cleaning the bathroom sink, protect the faucet
from any splattering of cleaner. Acids and cleaning uids will discolor or
remove chrome plating.

abrasive or chemical cleaners (including chlorine bleach) to

ONLY

mild soap and water, then wipe dry with

9

PARTS LIST

Item Part

1

2

3

No. No. Description

1 –– Spout Assembly
2 –– Integral Side Mixer Handle Cap

–– Integral Side Mixer Kit

3
4 EAF-2 Solenoid
5 –– Sensor Assembly
6 EAF-1 Mounting Hardware
7 EAF-44 Power Splitter
8 EAF-24-A 11-13/16” (300 mm) Extension Cable

EAF-25-A 47-1/4” (1200 mm) Extension Cable
EAF-17-A 126” (3200 mm) Extension Cable

9 EAF-1008 13” (330 mm) Flexible Supply Hose
10 EAF-9 Filter/Strainer
11 EAF-48 Battery Box
12 EAF-11-A Plug-in Voltage Adapter, US Plug

5

8

7

9

4

6

10

11

12

The information contained in this document is subject to change without notice.

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60133

Phone: 1-800-9-VALVE-9 (1-800-982-5839) • Fax: [phone] • www.sloanvalve.com

Copyright © 2011 SLOAN VALVE COMPANY Code No.: 0816409 – Rev. 1 (07/11)