SINGER CF User Manual [en, es]
CF
Household Steam Iron
instruction manual
2
3
IMPORTANT SAFETY INSTRucTIONS
READ ALL INSTRUCTIONS BEFORE USING.
Save these instructions in a safe place for future reference.
Use appliance only for its intended use.1.
To protect against risk of electrical shock, do not immerse the iron in water 2.
or other liquids.
This appliance should always be turned to “OFF” before plugging or unplug-3.
ging from an outlet. Never yank the cord to disconnect from outlet, always
grasp plug and pull to disconnect.
Always disconnect the appliance from the electrical outlet when filling with 4.
water or emptying or when not in use.
Do not allow cord to touch hot surfaces. Let the iron cool completely before 5.
putting away.
Do NOT operate appliance with a damaged cord, or if the appliance has 6.
been dropped or damaged. If electrical cord is damaged it must be replaced
by the manufacturer or authorized service agent to avoid a safety hazard.
To avoid the risk of electrical shock, do NOT disassemble the iron. Ship to 7.
the nearest authorized SINGER
®
approved service center for examination
and repair. Incorrect reassembly or repair can cause a risk of fire, electrical
shock, or injury when the appliance is used.
Not intended for use by children. Close supervision is necessary for any 8.
appliance being used near children. Unsupervised use can result in fire or
personal injury. Do not leave appliance unattended while plugged in, on an
ironing board, or while it is still hot.
Burns can occur from touching hot metal parts, hot water or steam. Use 9.
caution when you turn a steam iron upside down as there may be hot water
in the reservoir.
Never use or rest the iron on an unstable surface.10.
When iron is hot, never set on an unprotected surface.11.
SPECIAL INSTRUCTIONS:
To avoid a circuit overload, do not operate another high-wattage appliance on the
same circuit. If an extension cord is absolutely necessary, a 15-amp cord should
be used. Cords rated with less amperage may overheat. Use care to arrange the
cord so that it cannot be pulled or tripped over.
WARNING: THE POWER CORD ON THIS PRODUCT CONTAINS LEAD, A
CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.
FOR HOUSEHOLD USE ONLY
Getting to Know Your SINGER® Iron
8
12
1
2
3
4
5
7
9
Thermostat Light1.
Burst of Steam Button2.
Cool Mist Spray Button3.
Steam Level Indicator4.
Variable Steam Control Dial5.
Water Inlet Cover 6.
Spray Nozzle7.
Temperature Indicator8.
Self-Cleaning Button9.
Temperature Control Dial10.
Auto-Off Light11.
360° Swivel Cord12.
Soleplate13.
TECHNICAL SPECIFICATIONS: Voltage: 120V, 60 Hz Power: 1700 Watts
WARNING: TO AVOID FIRE, NEVER LEAVE IRON UNATTENDED WHILE
PLUGGED IN.
13
6
11
10
4
5
OPERATING INSTRucTIONS
Before First Use
Remove any protective films or stickers from the soleplate and the iron.•
Read all safety and operating instructions.•
Fill the water tank as described in “How to Fill Water”.•
Plug the iron into a grounded electrical outlet. The iron will begin to heat.•
Consult the garment’s label for temperature instructions or use the chart on •
page 6 of this manual for recommendations.
Select the appropriate temperature by turning the Temperature Control Dial •
clockwise. The Thermostat Light will glow.
When the selected temperature is reached, the Thermostat Light will turn off. •
Move the Variable Steam Control Dial to the maximum position •
.
On an ironing board or protected surface, iron an old towel or other heavy •
material until the water tank is empty and no more steam is produced.
It is normal for a small amount of smoke and a light odor to be produced the •
first time the iron is used. This will disappear quickly.
Particles may emit from the iron the first time it is used. They are not harmful •
and should disappear after the iron has been used as described above.
Filling the Water Tank
Ensure iron is unplugged.•
Move the Variable Steam Control Dial to • position.
Open the Water Inlet Cover and tilt the iron slightly forward, resting on its •
heel.
Using the filling cup provided, fill the water chamber to the MAX mark.•
Close the Water Inlet Cover.•
To refill the water tank during ironing, always unplug the iron. When you •
return to ironing, make sure the iron reheats to the desired level and the
Temperature Indicator light stops flashing before continuing.
Water Recommendations
Singer Home Essentials irons are designed to be used with regular tap water.•
If your water is especially hard or if you use a water softener, try using •
inexpensive bottled spring water.
Never use water with additives, including scents, starches, or fabric •
conditioners, as they can cause deposits to form in the iron that can stain
clothing.
WARNING: ALWAYS MAKE SURE THE IRON IS UNPLUGGED BEFORE FILLING
WITH WATER OR COMING INTO CONTACT WITH LIQUID OF ANY KIND.
6
7
Selecting the Temperature
Turning the Iron Off
To turn the iron off, unplug the iron.•
NOTE: Never yank the cord to disconnect from outlet. Always grasp plug and
pull to disconnect.
Plug the iron into a grounded electrical outlet. The iron will begin to heat. •
To adjust the temperature settings, turn the Temperature Control •
Dial clockwise and select the temperature setting according to the
recommendation on the garment label. The Temperature Indicator light will
glow.
When the selected temperature is reached, the Temperature Indicator light •
will turn off. The iron is ready to use.
CONSULT THE GARMENT’S LABEL FOR TEMPERATURE INSTRUCTIONS.
WE RECOMMEND USING THE CHART BELOW AS A GUIDE.
Dry Ironing
To iron without steam, turn the Variable Steam Control Dial to the “no steam” •
position .
Select the desired temperature (•
•, ••
, or
•••
).
To iron garments with a dry iron, SINGER recommends using this iron with an •
empty water tank.
IRONING YOuR GARMENTS
Steam Ironing
dry iron setting steam iron setting
Fill the water tank as described in “Filling the Water Tank” section. •
Plug the iron into a grounded electrical outlet. The iron will begin to heat. •
Select the •
•••
or MAX temperature setting by turning the Temperature
Control Dial clockwise.
When the selected temperature is reached, the Temperature Indicator light •
will turn off. The iron is ready to use.
Select the desired steam pressure on the Variable Steam Control Dial.•
When the selected temperature is reached, the Temperature Indicator light •
will turn off. The iron is ready to use.
TIP: The tougher the wrinkle, the more steam you will need.
WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING
WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.
Temperature Control Settings
acetate
elastane
polyamide
polypropylene
polyester
silk
triacetate
viscose
wool
cotton
linen
8
9
Burst of Steam
This function is ideal for removing stubborn wrinkles or pressing extra-sharp
creases.
Follow the instructions as described in the “Steam Ironing” section.•
While steam ironing, press the Burst of Steam button every 4 to 5 •
seconds. Most wrinkles can be removed within three bursts.
NOTE: It may be necessary to press the Burst of Steam button a few times to
start this function. For optimum steam quality, do not operate the Burst of Steam
more than three times in succession.
Vertical Burst of Steam
This feature enables you to remove wrinkles from hanging garments (jackets,
coats, shirts), hanging curtains, or other hanging fabric.
Follow the instructions as described in the “Steam Ironing” section.•
Hold the iron upright, 6-12 inches away from the garment.•
Press the Burst of Steam button to direct steam at the area.•
Steam will penetrate into the garment, removing the wrinkles.•
For stubborn wrinkles, wait 4 to 5 seconds before pressing the Burst of •
Steam button again. Most wrinkles can be removed within three bursts.
NOTE: Maintain a distance of 6-12 inches from delicate fabric (synthetics, silk,
velvet, etc.), otherwise the fabric could be damaged.
It may be necessary to press the Burst of Steam button a few times to start this
function. For optimum steam quality, do not operate the Burst of Steam more
than three times in succession.
WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING
WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.
WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING
WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.
burst of steamBurst of Steam Button vertical burst of steam
Cool Mist Spray
The Cool Mist Spray function can be used on any temperature setting. Use the
spray to dampen fabrics in order to remove tough wrinkles.
Aim the nozzle at the garment.•
Press the Cool Mist Spray Button. You may need to press the button a few •
times before the water sprays at full pressure.
Iron as usual.•
Do not spray silk. •
Cool Mist Spray Button cool mist spray
3-Way Smart Auto-Off
The SINGER Classic Finish Iron is equipped with an automatic shut-off. The
Smart Auto-Off switches the iron off if it has been left unattended.
If the iron is left on and is not moved for 8 minutes in a vertical position, it will •
automatically shut off and a beep will sound.
If the iron is left on its soleplate or tipped over, it will shut off after 30 seconds •
and an audible beep will sound.
The Smart Auto-Off Indicator light will flash, indicating the Auto-Off has been •
activated.
To de-activate the Auto-Off, move the iron or shake gently. The iron will take •
about 60 seconds to reach the previous soleplate temperature.
To turn the iron off, unplug the iron.•
Loading...