Siemens SHVPEE2 Instructions Manual
Quick and easy:
everything you need to know
about your dishwasher...
You should, however, still
read the installation and
operating instructions before
you use the dishwasher for
the first time.
Switch on the appliance the dishwasher starts...
Switch off the appliance that’s it...
Press the on/off switch, the cycle time
for the programme selected appears
Press the on/off switch when
the indicator shows 0 (programme end)
Pour in the water/special salt
Pour in the rinsing agent
Pour in the cleaning agent
Select the programme
Summary of instructions for dishwasher
9000 199 847
en
Set the water softening system *
Quickly sorted ...
Find out the water hard-
ness at your water utility
company and enter
* only before using the dish-
washer for the first time or
if the water hardness
changes
Read off the setting ... and then set
– Hold down programme button B and switch on the main
switch, then release the buttons. The display of button B
and the number 4 set by the factory flash.
– Each time button B is depressed, the setting increases by
one; if 7 has been reached, the display jumps back to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
Reset
A B C
Dissolves limescale (not required for set value 0!)
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
2 pt water into the
salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never detergent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Close the
lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufacturer’s instructions.
Pour in
detergent.
Push the lid
shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
138
1,65
16
13
140
1,05
14
–
75
0,90
14
11
30
0,80
10
–
19
0,05
4
–
45_ 50_ 70_ 65_ 40_
Duration in minutes
Power consumption in kWh
Water consumption in litres
With Aqua sensor
Intensive Normal Eco
Gentle
Quick
Prerinse
140
1,60
16
–
Additional programmes **
Increased flexibility ...
** on some models
h.
Time selection
...switches on as soon as
you press the time
selection button:
Alters the programme
start in hourly steps
Upper basket cleaning
...Only the crockery in the
upper basket is cleaned
Maintenance and care
For perfect rinsing results ...
Cleaning the waste-water pump *
Strainers ...
Check, if
required, clean
Rotate filter
cylinder, remove
filter system ...
rinse under
flowing water ...
Insert ... Screw in filter
system NOTE
MARK!
* With some models
– Ladle out water and remove filters
– Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Spray arms ...
Remove
blockages/deposits
Pull lower arm
upwards ...
Unscrew upper
arm ...
Clean spray nozzles
under flowing water
(perhaps with
toothpick) ...
Insert lower arm ...
Screw in upper arm
Rectifying minor faults yourself ...
... as it is worth doing it yourself!
Fault Possible causes
Appliance is not running /
stops
Check water supply
Display lights up
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Open supply fitting.
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min. when
water supply is open.
If the flow rate is less, replace the
supply fitting.
Remedial action
Plastic / utensils
discoloured
Too little detergent
Discoloration caused by food colourings
(tomato sauce)
Follow manufacturer’s instructions
(detergent).
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Residual water
in the appliance
Waste water pump blocked
The programme has not yet ended
Clean waste-water pump (see above).
Switch on appliance and close or
terminate programme (see Terminating
the programme).
Rust on the cutlery Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Use dishwasher-proof cutlery.
Never wash rusting parts
in the appliance.
Fault Possible causes Remedial
action
Stains and streaks
Milky film on the utensils
(removable)
Rinse-aid dosage too high / too low
Glasses not dishwasher-proof.
Streaks: reduce dosage.
Water or limescale stains: increase
dosage.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
More information can be found in the operating instructions
Milky film, glasses
cloudy / dull
(not removable)
Water softening system incorrectly set;
No salt
Correctly set water softening system.
Refill with salt.
Utensils are not clean
Sand or gritty residue
on the utensils
Utensils are situated close together
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Separate the utensils, prevent contact
points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Stopping the programme ... Loading the dishwasher correctly ...
Press and hold the two
reset buttons simultaneously for
approximately 3 seconds while
the programme is running
(RESET)
”0” appears
The programme will stop
after 1 minute
Switch off the appliance.
Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
large remnants of jam, dairy products and food) according to the operating instructions and check that
the spray arms can rotate freely.
Loading...