Siemens REV24 Series, REV34 Operating Instructions Manual

REV24..

Operating instructions

REV24.. - 7-day room temperature controller for the right temperature at the right time. All factory
settings already provide optimal living comfort. You can easily adjust the controller to your needs
with the user-assisted clear-text display and program selection slider.

Note the following for placing the controller:

• Make sure no other influencing factors influence the controller's temperature sensor (no solar radiation and
other heat or cold source influences).

Info button
Increase values, set time or

make a selection
Change between Comfort and

energy saving temperature
(active until next switching time)
and Part

y

function

Decrease values, set time or
make a selection

Operating mode
selector:

- Automatic

- Exception day

- Comfort mode

- Energy saving
mode

- Protection
mode

Program selection slider

RUN

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Operating elements and settings

Time setting

Date

Day / Month / Year

Weekdays 1-5

Weekend 6-7

Individual da

y

s 1..7

1, 2 or 3

Comfort phases

Start time

Comfort phase 1

Temperature

Comfort phase 1

End

Comfort phase 1

Start time

Comfort phase 2

Temperature

Comfort phase 2

End

Comfort phase 2

Start time

Comfort phase 3

Temperature

Comfort phase 3

End

Comfort phase 3

Saving temp. time

program

Start

Absence

Temperature

Absence

End

Absence

Temperature

remote control

Slider positions

If the selected operating mode does not support the setting, the time display shows PASS.

Special symbols displayed

The controller display can show the following special symbols:

Is symbol displayed ?

The alarm indicates an error!

Press the Info button and check the error message (e.g. radio clock signal, radio connection to receiver, etc.).
Contact a specialist as needed.

Is symbol displayed ?

This symbol tells you that you must exchange the batteries within the next 3 months.

Insert 2 new alkaline batteries type AA, 1.5 V as follows:
Remove the controller from the mounting base; open the battery compartment on the rear; remove the old

batteries; insert the new batteries and reinsert the controller in the base.
Caution: Time and date are retained for max. 1 minute.

(All other settings are fixed and remain unchanged!)
Dispose of the batteries as per regulations.

Is symbol displayed ?

The radio clock symbol only appears if the receiver is set up and activated to receive the
time signal from Frankfurt (Germany). A permanent symbol indicates that both time and
date of the controller are synchronized to Frankfurt (DCF77).
The symbol flashes if the signal is not received for more than 1 week.

Is symbol or displayed ?

The controller is in "heating mode“ or "cooling mode“ .

Commission the controller and quick start

The controller contains a factory-set comfort switching pattern and temperature values.
Proceed as follows for initial commissioning:

Remove the controller from the mounting base and pull off the black insulating
tape from the 2 batteries: The controller turns on automatically. Reinsert the
controller in the mounting base.

After startup, a welcome message appears for ca. 2 minutes. Press a button
to interrupt the message. Language selection starts with “ENGLISH“ (factory

setting). Press

or until your language appears. Press or move

the slider to accept your language.
Slider in position 1 (time setting): Press or to set the time.

Note: You do not need to enter the time when DCF77 receiver for the
time signal from Frankfurt (Germany) is equipped.

Slider in position 2 (date: day/month/year): Press or to set the date.
Note: You do not need to enter the date when DCF77 receiver for the

time signal from Frankfurt (Germany) is equipped.

RUN

Move the slider to the very right to position RUN (only way to close the cover).
Set the operating mode with the operating mode selector.
Factory setting is

.

Fold the operating instructions and reinsert in the mounting base.

Turn on display lighting, check error messages or other imp ortant
information

Press the Info button once to activate display backlighting. Backlighting
goes off automatically after a short time.
Continuing to press the Info button activates the information display:
is lit. The device first shows pending error messages and then important
information (e.g. switching programs, ...).

Change the temperature level in the time switch program,
or are you not at home for a while?

In the time switch program, press this button to change from the current
temperature level to the next and back.

Quickly activate energy saving temperature when you leave the apartment
briefly to save energy.

The change appears on the display. It is valid only until the next switching
time.

Tips to save energy without reducing comfort

• Heat your rooms to max 21 °C.

• Use to switch to energy saving temperature even if you are absent only briefly.

• Air out your rooms briefly, but with wide-open windows.

Day of week
Low battery

Radio Clock Date Setting: 1-5, 6-7, 1..7/
active Reading: 1..7

Time display
Remote control active
Holiday mode

Display

Info mode
Installer mode
Temperature

setpoint symbols
Text display
Alarm
Cooling mode /

Heating mode
Switching pattern

with time cursor

Automatic mode
Party mode active
Exception day mode
Continuous comfort mode
°C or °F
Continuous energy

saving mode
Heating On /

Cooling On
Protection mode
Temperature display

B2205en 25.12.2007 Siemens, Building Technologies

Select operating mode

Press the operating mode button to select one of 5 modes.

Operating modes with time program

The controller offers both time programs Automatic and Exception day .

Do you feel too warm / too cold ?

Press or to set the temperature. The setting is temporary and active only until the
next time the controller activates a change.

Note: To set your own programs, see: "Enter customized temperatures and switching times".

Continuous operating modes

The controller offers continuous operating modes "Continuous comfort mode“ ,
"Continuous energy saving mode“

and protection mode (frost or overheating) .

Do you feel too warm / too cold?

Press or to set a continuous temperature.

Enter time and date

Slider in position 1 (time setting): Press or to set the time.

Slider in position 2 (date: Day/month/year): Press or to set the date.

RUN

Reset the slider to the RUN position.

Note: You do not need to enter time and date when DCF77 receiver for the time signal
from Frankfurt (Germany) is equipped. The time display shows PASS.

Enter customized temperatures and switching times

The controller has three different switching patterns that you can allocate to the weekday blocks
1-5, the weekend block 6-7, or to the individual days 1…7.
Proceed as follows:

Select operating mode or .
Slider in position 3 (weekdays

, weekend , individual days ):

Press

or to select the block (weekdays, weekend) or individual day.

Note: Making changes to individual days destroys the corresponding block.
You can only restore a destroyed block by Reset the controller.

Slider in position 4 (number of comfort phases): Press

or to set the

number of comfort phases.
Slider in position 5 (start time comfort phase 1): Press

or to set the

start time.
Slider in position 6 (temperature comfort phase 1): Press

or to set the

temperature.
Slider in position 7 (end time comfort phase 1): Press

or to set the

end time.

, ,

, ,

Slider positions 8…10 (comfort phase 2) and slider positions 11…13
(comfort phase 3): Same procedure as above for comfort phase 1.

Slider in position 14 (energy saving temperature in time switch programs
Automatic and Exception day): Press

or to set the temperature.

Note: The energy saving temperature is valid Monday through Sunday.
It does not depend on operating mode "Continuous energy saving".

RUN

Move the slider to RUN position and close the cover.

Notes (e.g. individual settings):

Enter holidays or absence

You can enter start, temperature and end of your holidays. The controller switches to the set holiday
temperature at the start of the holidays and back to the preset operating mode at the end of the holidays.

During holiday mode, symbol

flashes and the end of the holidays is displayed.

Proceed as follows:

Slider in position 15 (start of absence): Press or to set the start of the holidays (date).
Slider in position 16 (temperature during absence): Press or to set the temperature

effective during the holidays.
Slider in position 17 (end of absence): Press or to set the end of the holidays (date).

RUN

Move the slider back to RUN. Symbol appears to the left of symbol .
To quit holiday mode prematurely, press , , , or move the slider.

Enter temperature for active remote control

With remote control, you are free to select the temperature. Activating remote control immediately
enables control to the remote operating temperature regardless of the current operating mode. After you
switch off remote control, the device returns to the set operating mode.

Symbol

flashes with active remote control.

Proceed as follows:

Slider in position 18 (temperature for active remote control): Press or to set the
temperature for active remote control.

RUN

Move the slider back to RUN.

Reset to factory settings

Press and together with the operating mode button for 3 seconds. All temperature
and time settings are reset to default values.
The clocks starts at 12:00.

Caution: All customized settings are lost !

Factory settings: Heating Factory settings: Cooling

, , ,

20 °C

, , ,

24 °C

,

16 °C

,

28 °C

8 °C

35 °C

,

12 °C

,

30 °C

Factory settings: Switching times
Comfort phases P1 P2 P3 P4 P5 P6

1. 07:00 23:00 PASS PASS PASS PASS

2. 06:00 08:00 17:00 22:00 PASS PASS

3. 06:00 08:00 11:00 13:00 17:00 22:00

Activate Party mode

You can activate Party mode only in operating modes and . In Party mode, the device controls
to any selectable temperature for any selectable time.

In Party mode, symbol

is displayed along with the end of Party mode.

Proceed as follows:

B2205en 25.12.2007 Siemens, Building Technologies

1. Press for 3 seconds.

2. Press or to set the duration for Party mode. Party mode can last max. 9 hours.

The entry is accepted after 20 seconds or when you press .

3. Press or to set the temperature.

4. Party mode ends automatically after the Party duration ends or when you press

or .