Siemens PA-3 User Manual

Download

Page 1

PA-3 Power Adapter (50 Hz/Oil-Filled)

Document No. 96A0260

Issued: December 15, 1999 Rev. B: May 16, 2001

Page 2

PA-3 Power Adapter (50 Hz/Oil-Filled) Record of Changes

Record of Changes

Page Rev Description EC No. Checked Approved Date

A Released new manual. 00350 BW WT 12/15/99

All B Changed to new title page. Changed ADB to

Siemens Airfield Solutions.

00696 JY WT 5/16/01

Page 3

PA-3 Power Adapter (50 Hz/Oil-Filled) Table of Contents

Record of Changes........................................................................................ ii

Table of Contents......................................................................................... iii

Warranties......................................................................................................v

1. Safety........................................................................................................1

Safety Symbols .....................................................................................1

Qualified Personnel ..............................................................................2

Intended Use.........................................................................................2

Installation ............................................................................................3

Operation ..............................................................................................3

Action in the Event of a System or Component Malfunction ...............4

Maintenance and Repair .......................................................................4

2. Description ...............................................................................................5

Introduction ..........................................................................................5

PA-3 Power Adapter (50 Hz): Required Equipment.............................6

PA-3 Power Adapter (50 Hz) Specifications ........................................7

Load on CCR for Fully Loaded PA-3 Power Adapter (50 Hz) .........7

PA-3 Power Adapter (50 Hz) Technical Features.............................7

Construction......................................................................................7

Weight...............................................................................................8

Dimensions........................................................................................8

Short Circuit Protection.....................................................................8

Serviceability ....................................................................................8

3. Installation ................................................................................................9

Introduction ..........................................................................................9

Unpacking.............................................................................................9

Installation ............................................................................................9

Method of Installation.......................................................................9

Power Adapter Connectors..............................................................10

PA-3 Power Adapter (50 Hz) Installation on 6.6 A Series Circuit..11

Wiring Checkout and Startup ..........................................................11

4. Repair .....................................................................................................12

Introduction ........................................................................................12

Disassembling PA-3 Oil-Filled Power Adapter ..................................12

Assembling PA-3 Oil-Filled Power Adapter ......................................13

5. Parts........................................................................................................15

Using the Illustrated Parts List............................................................15

PA-3 Power Adapter (50 Hz) Part Number ........................................16

PA-3 Power Adapter (50 Hz) Spare Parts ..........................................16

6. Wiring Schematics..................................................................................17

Page 4

PA-3 Power Adapter (50 Hz/Oil-Filled) Table of Contents

List of Figures

List of Tables

Figure 1. Siemens Airfield Solutions PA-3 Power Adapter

(50 Hz/Oiled-Filled) ....................................................................5

Figure 2. PA-3 Power Adapter (50 Hz) (Top View)...................................10

Figure 3. PA-3 Power Adapter (50 Hz) Spare Parts...................................16

Figure 4. PA-3 Power Adapter (50 Hz) Wiring Schematic

for Internally Lighted Wind Cones ............................................17

Table 1. Power Source/Load Capacity .......................................................6

Table 2. Required Equipment Supplied......................................................6

Table 3. Required Equipment Not Supplied...............................................6

Table 4. PA-3 Power Adapter (50 Hz) CCR Load .....................................7

Table 5. PA-3 Power Adapter (50 Hz) Technical Features ........................7

Table 6. Environmental Conditions............................................................7

Table 7. Weight ..........................................................................................8

Table 8. Dimensions...................................................................................8

Table 9. L-867 Can Dimensions.................................................................9

Table 10. PA-3 Power Adapter (50 Hz) Connectors ..................................10

Table 11. PA-3 Power Adapter (50 Hz) Replacement Parts.......................12

Page 5

PA-3 Power Adapter (50 Hz/Oil-Filled) Warranties

Products of Siemens Airfield Solutions manufacture are guaranteed against

Warranties

mechanical, electrical, and physical defects (excluding lamps) for a period of one year from the date of installation or a maximum of two years from the date of shipment and are guaranteed to be merchantable and fit for the ordinary purposes for which such products are made.

Siemens Airfield Solutions will correct by repair or replacement, at its option, equipment or parts which fail because of mechanical, electrical or physical defects, provided that the goods have been properly handled and stored prior to installation, properly installed and properly operated after installation, and provided further that Buyer gives Siemens Airfield Solutions written notice of such defects after delivery of the goods to Buyer.

Siemens Airfield Solutions reserves the right to examine goods upon which a claim is made. Said goods must be presented in the same condition as when the defect therein was discovered. Siemens Airfield Solutions furthers reserves the right to require the return of such goods to establish any claim.

Siemens Airfield Solutions’s obligation under this guarantee is limited to making repair or replacement within a reasonable time after receipt of such written notice and does not include any other costs such as the cost of removal of defective part, installation of repaired product, labor or consequential damages of any kind, the exclusive remedy being to require such new parts to be furnished.

Disclaimers

Siemens Airfield Solutions’s liability under no circumstances will exceed the contract price of goods claimed to be defective. Any returns under this guarantee are to be on a transportation charges prepaid basis. For products not manufactured by, but sold by Siemens Airfield Solutions, warranty is limited to that extended by the original manufacturer.

This is Siemens Airfield Solutions’s sole guarantee and warranty with respect to the goods; there are no express warranties or warranties of fitness for any particular purpose or any implied warranties of fitness for any particular purpose or any implied warranties other than those made expressly herein. All such warranties being expressly disclaimed.

This manual could contain technical inaccuracies or typographical errors. Siemens Airfield Solutions reserves the right to revise this manual from time to time in the contents thereof without obligation of Siemens Airfield Solutions to notify any person of such revision or change.

Details and values given in this manual are average values and have been compiled with care. They are not binding, however, and Siemens Airfield Solutions disclaims any liability for damages or detriments suffered as a result of reliance on the information given herein or the use of products, processes or equipment to which this manual refers. No warranty is made that the use of the information or of the products, processes or equipment to which this manual refers will not infringe any third party’s patents or rights. The information given does not release the buyer from making their own experiments and tests.

Page 6

PA-3 Power Adapter (50 Hz/Oil-Filled) Safety

PA-3 Power Adapter (50 Hz/Oil-Filled)

1. Safety

This section contains general safety instructions for using your Siemens Airfield Solutions equipment. Some safety instructions may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this manual where appropriate. Note all warnings and follow all instructions carefully. Failure to do so may result in personal injury, death, or property damage.

To use this equipment safely,

• refer to the FAA Advisory Circular AC 150/5340-26, Maintenance of

Airport Visual Aids Facilities, for instructions on safety precautions.

• observe all safety regulations. To avoid injuries, always remove power

prior to making any wire connections and touching any parts. Refer to FAA Advisory Circular AC 150/5340-26.

• read and become familiar with the general safety instructions provided

in this section of the manual before installing, operating, maintaining, or repairing this equipment.

• read and carefully follow the instructions given throughout this manual

for performing specific tasks and working with specific equipment.

• store this manual within easy reach of personnel installing, operating,

maintaining, or repairing this equipment.

• follow all applicable safety procedures required by your company,

industry standards, and government or other regulatory agencies.

• obtain and read Material Safety Data Sheets (MSDS) for all materials

used.

Safety Symbols

Become familiar with the safety symbols presented in this section. These symbols will alert you to safety hazards and conditions that may result in personal injury, death, or property and equipment damage.

WARNING: Failure to observe this warning may result in

personal injury, death, or equipment damage.

WARNING: Risk of electrical shock. Failure to observe this

warning may result in personal injury, death, or equipment

damage.

Page 7

PA-3 Power Adapter (50 Hz/Oil-Filled) Safety

Safety Symbols (contd.)

Qualified Personnel

Intended Use

WARNING: Disconnect equipment from line voltage. Failure

to observe this warning may result in personal injury, death, or

equipment damage.

WARNING: Wear safety goggles. Failure to observe may

result in serious injury.

CAUTION: Failure to observe may result in equipment

damage.

The term qualified personnel is defined here as individuals who thoroughly understand the equipment and its safe operation, maintenance, and repair. Qualified personnel are physically capable of performing the required tasks, familiar with all relevant safety rules and regulations and have been trained to safely install, operate, maintain, and repair the equipment. It is the responsibility of the company operating this equipment to see that its personnel meet these requirements.

WARNING: Use of this equipment in ways other than

described in this manual may result in personal injury, death, or

property and equipment damage. Use this equipment only as

described in this manual.

Siemens Airfield Solutions cannot be responsible for injuries or damages resulting from nonstandard, unintended applications of its equipment. This equipment is designed and intended only for the purpose described in this manual. Uses not described in this manual are considered unintended uses and may result in serious personal injury, death, or property damage. Unintended uses may result from taking the following actions:

• making changes to equipment that have not been recommended or

described in this manual or using parts that are not genuine Siemens Airfield Solutions replacement parts

• failing to make sure that auxiliary equipment complies with approval

agency requirements, local codes, and all applicable safety standards

• using materials or auxiliary equipment that are inappropriate or

incompatible with your Siemens Airfield Solutions equipment

• allowing unqualified personnel to perform any task

 2001 Siemens Airfield Solutions, Incorporated 96A0260B Page 2

Page 8

PA-3 Power Adapter (50 Hz/Oil-Filled) Safety

Installation

Read the installation section of all system component manuals before installing your equipment. A thorough understanding of system components and their requirements will help you install the system safely and efficiently.

WARNING: Failure to follow these safety procedures can

result in personal injury or death.

• Allow only qualified personnel to install Siemens Airfield Solutions and

auxiliary equipment. Use only approved equipment. Using unapproved equipment in an approved system may void agency approvals.

• Make sure all equipment is rated and approved for the environment in

which you are using it.

• Follow all instructions for installing components and accessories.

• Install all electrical connections to local code.

• Use only electrical wire of sufficient gauge and insulation to handle the

rated current demand. All wiring must meet local codes.

• Route electrical wiring along a protected path. Make sure they will not

be damaged by moving equipment.

• Protect components from damage, wear, and harsh environment

conditions.

• Allow ample room for maintenance, panel accessibility, and cover

removal.

• Protect equipment with safety devices as specified by applicable safety

regulations.

• If safety devices must be removed for installation, install them

immediately after the work is completed and check them for proper functioning.

Operation

Only qualified personnel, physically capable of operating the equipment and with no impairments in their judgment or reaction times, should operate this equipment.

Read all system component manuals before operating this equipment. A thorough understanding of system components and their operation will help you operate the system safely and efficiently.

Page 9

PA-3 Power Adapter (50 Hz/Oil-Filled) Safety

Operation (contd.)

Action in the Event of a System or Component Malfunction

• Before starting this equipment, check all safety interlocks, fire-detection

systems, and protective devices such as panels and covers. Make sure all devices are fully functional. Do not operate the system if these devices are not working properly. Do not deactivate or bypass automatic safety interlocks or locked-out electrical disconnects or pneumatic valves.

• Never operate equipment with a known malfunction.

• Do not attempt to operate or service electrical equipment if standing

water is present.

• Use this equipment only in the environments for which it is rated. Do

not operate this equipment in humid, flammable, or explosive environments unless it has been rated for safe operation in these environments.

• Never touch exposed electrical connections on equipment while the

power is ON.

Do not operate a system that contains malfunctioning components. If a component malfunctions, turn the system OFF immediately.

• Disconnect and lock out electrical power.

• Allow only qualified personnel to make repairs. Repair or replace the

malfunctioning component according to instructions provided in its manual.

Maintenance and Repair

Allow only qualified personnel to perform maintenance, troubleshooting, and repair tasks. Only persons who are properly trained and familiar with Siemens Airfield Solutions equipment are permitted to service this equipment.

• Always use safety devices when working on this equipment.

• Follow the recommended maintenance procedures in your equipment

manuals.

• Do not service or adjust any equipment unless another person trained in

first aid and CPR is present.

• Connect all disconnected equipment ground cables and wires after

servicing equipment. Ground all conductive equipment.

• Use only approved Siemens Airfield Solutions replacement parts.

Using unapproved parts or making unapproved modifications to equipment may void agency approvals and create safety hazards.

Page 10

PA-3 Power Adapter (50 Hz/Oil-Filled) Description

Maintenance and Repair

(contd.)

2. Description

Introduction

• Check interlock systems periodically to ensure their effectiveness.

• Do not attempt to service electrical equipment if standing water is

present. Do not service electrical equipment in a high-humidity environment.

• Use tools with insulated handles when working with electrical

equipment.

See Figure 1.

This section describes the Siemens Airfield Solutions PA-3 series-toregulated-voltage power adapter (50 Hz/oil-filled).

Figure 1. Siemens Airfield Solutions PA-3 Power Adapter (50 Hz/Oiled-Filled)

Page 11

PA-3 Power Adapter (50 Hz/Oil-Filled) Description

Introduction (contd.)

PA-3 Power Adapter (50 Hz): Required Equipment

The Siemens Airfield Solutions PA-3 power adapter (50 Hz) can be used to power the L-807 internally lighted wind cone. Refer to Table 1 for power source and load capacity.

NOTE: The Siemens Airfield Solutions power adapter is not approved for use with other manufacturers’ products. Contact the Siemens Airfield Solutions sales department if it is desired to connect the PA-3 power adapter (50 Hz) to other products.

Table 1. Power Source/Load Capacity

VA Load Capacity Power Source

120 Vac at 300 VA 5-step, 6.6 A, 50-Hz series lighting circuit

Refer to Table 2 for required equipment that is supplied. Refer to Table 3 for required equipment that is not supplied. Refer to the Parts section for ordering information.

Table 2. Required Equipment Supplied

Description Quantity

PA-3 power adapter (50 Hz/oil-filled) 1 Instruction manual 1 per order

Table 3. Required Equipment Not Supplied

Description Quantity

L-823 Primary Cable Connector Kit contains one male and one female connector L-823 two-pole plug connector for connection of secondary lead External circuit breaker, if required 1 Ground wire (AWG 8 minimum) 1 L-867 base, 16-in.- (40.64-cm-) diameter, with minimum height of 24 in. (50.8 cm)

Page 12

PA-3 Power Adapter (50 Hz/Oil-Filled) Description

PA-3 Power Adapter (50 Hz) Specifications

This subsection describes the specifications for the Siemens Airfield Solutions PA-3 power adapter (50 Hz).

Load on CCR for Fully Loaded PA-3 Power Adapter (50 Hz)

Refer to Table 4 for PA-3 power adapter (50 Hz) CCR load.

Table 4. PA-3 Power Adapter (50 Hz) CCR Load

Step Load

B1 375 W B3 590 W B5 1140 W

PA-3 Power Adapter (50 Hz)Technical Features

Refer to Table 5. This subsection describes technical features of the PA-3 power adapter (50 Hz).

NOTE: The portion of the VA load on the CCR due to the power adapter should be no more than 50%.

Table 5. PA-3 Power Adapter (50 Hz) Technical Features

Minimum Load Maximum

Load

25 VA 300 VA +3% to -3%

NOTE A: Load regulation of +10% to -5% is valid for 3-step CCR over 4.7−6.7 A.

B: Primary leads are 30 inches (76.20 cm) long. Secondary leads are 49 inches (124.46 cm) long.

Load Regulation (No Load to Full

Load)

Input Current

Range

2.72−6.7 A

Construction

The PA-3 power adapter (50 Hz) is watertight for direct earth burial, surface installation, or installation in an L-867 base (16-inch- [40.64-cm-] diameter base with a minimum height of 24 inches [50.8 cm]).

Environmental Conditions

Refer to Table 6 for environmental conditions.

Table 6. Environmental Conditions

Temperature Range Humidity Altitude

-55 to +55 °C (-67 to +131 °F) 0 to 100% Sea level to 10,000 feet

Output Voltage

Single Phase

60 Hz

120 Vac 2 primary

1 secondary

(3,000 m)

Leads Note

Page 13

PA-3 Power Adapter (50 Hz/Oil-Filled) Description

Weight

Refer to Table 7 for the PA-3 power adapter (50 Hz) weight.

Table 7. Weight

Weight lb Weight kg

118 52.7208

Dimensions

Refer to Table 8 for the PA-3 power adapter (50 Hz) dimensions.

Table 8. Dimensions

Dimension in. cm

Diameter 10.75 27.305

Height 22.00 55.88

Short Circuit Protection

All Siemens Airfield Solutions adapters are self-protected against an output short circuit.

Serviceability

The PA-3 power adapter (50 Hz) is oil-filled and can be serviced.

NOTE: No PCB exists in the PA-3 power adapter (50 Hz/oil-filled).

Page 14

PA-3 Power Adapter (50 Hz/Oil-Filled) Installation

3. Installation

Introduction

Unpacking

Installation

WARNING: Allow only qualified personnel to perform the

following tasks. Observe and follow the safety instructions in

this document and all other related documentation.

WARNING: The power adapters are heavy. Exercise caution

when lifting or moving power adapters. Use the handle, not the

leads, to lift the power adapter. Failure to observe this warning

may result in personal injury.

This section describes instructions for installing the PA-3 power adapter (50 Hz/oil-filled) on series circuits. Refer to airport project plans and specifications for the specific installation instructions.

Unpack the carton/crate upon receipt and examine the power adapter to ensure no damage has occurred during shipment. Note any exterior damage to the carton that might lead to detection of equipment damage.

If you note any damage to any equipment, file a claim with the carrier immediately. The carrier may need to inspect the equipment.

This subsection describes installation information.

Method of Installation

The watertight PA-3 power adapter (50 Hz) assembly is satisfactory for direct earth burial or above-surface installation. Install the PA-3 upright within 15 degrees of vertical. The preferred method of installation is to install the power adapter in a deep L-867 can. Refer to Table 9 for L-867 can dimensions.

Table 9. L-867 Can Dimensions

L-867 Can Diameter Opening (Minimum)

in. (cm)

16 (40.64) 24 (60.96)

L-867 Can Height

in. (cm)

Page 15

PA-3 Power Adapter (50 Hz/Oil-Filled) Installation

Power Adapter Connectors

See Figure 2. Refer to Table 10 for PA-3 power adapter (50 Hz) connectors.

Table 10. PA-3 Power Adapter (50 Hz) Connectors

Leads Lead Plug/Receptacle Note

One 49-inch (124.46-cm) secondary lead Style 8 female receptacle (J2) A

Two 30-inch (76.20-cm) primary leads L-823 Style 2 male plug (P1)

Style 9 female receptacle (J1)

NOTE A: The largest pin hole on the Style 8 female receptacle is neutral. The neutral connection is floating but can be

grounded if desired.

Figure 2. PA-3 Power Adapter (50 Hz) (Top View)

1. Air-Fill Valve 4. J1 Cordset 7. J2 Cordset

2. P1 Cordset 5. Ground Lug 8. Pressure Relief Valve

3. Cord Grip 6. Oil-Fill Plug

Page 16

PA-3 Power Adapter (50 Hz/Oil-Filled) Installation

PA-3 Power Adapter (50 Hz) Installation on 6.6 A Series Circuit

WARNING: Disconnect power to the lighting circuit before

attempting to make any electrical connections. Coordinate a

power outage with air traffic personnel before turning off power

to the airport lighting system.

To connect the PA-3 power adapter (50 Hz) to a 6.6 A series circuit, perform the following procedure:

1. If no direct interconnection is possible, cut the runway lighting circuit

in accordance with proper airport installation authority regulations.

NOTE: If the power adapter is installed near a runway circuit splice such as an isolation transformer, the runway lighting circuit cable will not need to be cut.

2. Use a single-pole L-823 connector kit to terminate the cut wire ends of

the series circuit. Refer to FAA Advisory Circular AC 150/5345-26.

3. Using a minimum AWG 8 wire, connect a good earth ground to the

earth ground stud on the top of the power adapter.

Wiring Checkout and Startup

To verify wiring is working properly, perform the following:

• Check for proper installation and firm connections.

• Measure output voltage of power adapter on each step using a true rms

voltmeter with load on the power adapter turned on.

NOTE: No actual startup procedure for the power adapter exists. The power adapter is considered to be a part of the runway lighting circuit, and has no on/off switching devices. Power is present on the output leads of the power adapter when the series lighting circuit is energized.

Page 17

PA-3 Power Adapter (50 Hz/Oil-Filled) Repair

4. Repair

Introduction

WARNING: Allow only qualified personnel to perform the

following tasks. Observe and follow the safety instructions in

this document and all other related documentation.

WARNING: De-energize the regulator supplying power to the

circuit connected to the power adapter. Failure to observe this

warning may result in personal injury, death, or equipment

damage.

This section provides procedures for repairing and servicing the PA-3 power adapter (50 Hz).

Under normal operating conditions the internal components of the oil-filled PA-3 power adapter will not require service. In the unlikely event of a component failure in the power adapter or if a fuse blows or a tap needs to be changed, the power adapter can be serviced and repaired. To access and service the components, follow the disassembling and assembling procedures in this section.

Refer to Table 11 for replacement parts for the PA-3 power adapter (50 Hz).

Table 11. PA-3 Power Adapter Replacement Parts

Description Quantity Part Number

Capacitor, 30 µF

Gasket (RTV) 1 10 oz caulking tube 67A0043 Insulating oil 5 gallons

2 20A0040

(approximately)

Shell Diala. Contact local Shell oil agent or phone 1-800-231-6950.

Disassembling PA-3 Oil-filled Power Adapter

To disassemble the PA-3 oil-filled power adapter, perform the following procedure:

1. Turn off the power to the circuit, and remove the power adapter from

the can in the field for disassembly in a shop. Reconnect the L-823 connectors and close the can to use the series circuit, if necessary.

2. Place the power adapter upright on the floor and remove twelve hex

nuts located on the perimeter of the lid of the power adapter.

NOTE: Do not lay power adapter on its side to remove hex nuts. Do not remove any other bolts or components found on the outside lid of the power adapter.

Page 18

PA-3 Power Adapter (50 Hz/Oil-Filled) Repair

Disassembling PA-3 Oil-filled Power Adapter (contd.)

3. After removing the hex nuts, insert a utility knife into the blue RTV

gasket material located between the lid and the can flange. Insert the knife as deep as possible to cut the gasket material. Repeat this process around the entire diameter of the can lid.

4. After cutting the gasket material, insert a flat-bladed screwdriver

between the lid and the can flange and pry the lid loose. Repeat this process in four places 90 degrees apart. Use a small hammer, if necessary, to force the screwdriver under the lid.

5. Once the lid is loose, grasp the handles on the top of the lid and lift the

power adapter lid that has the component plate attached out of the canister.

NOTE: The lid assembly weighs approximately 86 pounds (39.009 kg). It is recommended that two individuals do the lifting. An

alternate method is to use a small overhead crane to lift the lid assembly out of the canister.

6. Place the component package on the workbench. Troubleshoot the

system and make any necessary repairs.

Assembling PA-3 Oil-filled Power Adapter

7. After repairs, perform a systems check before installing the lid with the

component package into the canister. Clean all gasket material from the lid and from the canister flange.

To assemble the PA-3 oil-filled power adapter, perform the following procedure:

1. Clean all gasket material from the lid and from the canister flange.

Prevent gasket material from falling into the oil. Remove any RTV that has fallen into the oil.

2. Inspect the condition of the transformer oil. Oil level should be

6 inches (15.24 cm) from the top of the canister. The oil should be replaced if the oil is contaminated with water or dirt.

NOTE: Shell Diala transformer oil is used in the canister. This oil does not contain any PCBs. Dispose of used oil in accordance with local, state, and federal EPA regulations.

3. Refill with Shell Diala transformer oil only. Fill with approximately 5

gallons of oil to within 6 inches (15.24 cm) of the top of the canister.

Page 19

PA-3 Power Adapter (50 Hz/Oil-Filled) Repair

Assembling PA-3 Oil-filled Power Adapter (contd.)

4. Make sure that all components are clean and free of any contaminants.

Clean as necessary. If power cords or squeeze connectors have been replaced, make sure the connector is sealed around the cord. Use any quality pipe dope on the connector threads.

5. After removing all of the old gasket material, apply a 3/8-inch-

(.953-cm-) diameter (minimum) bead of sealant around the entire canister flange. Locate the bead just inside the screw holes in the flange. Apply a smaller circle of sealant around each of the screw holes.

6. Position the component package over the canister. Align the holes in

the lid with the studs and insert the component package into the canister.

7. Reinstall the twelve nuts and lockwashers. Apply Loctite AV or

equivalent to the stud threads and then install hex nuts. Hand tighten hex nuts to secure lid to prevent RTV from being totally squeezed out. After tightening the hex nuts, wipe off the excess RTV and form a thin gasket film around the joint between the lid and the flange.

CAUTION: Do not torque hex nuts.

8. After allowing the RTV to cure for two hours, use the air-fill valve on

the top of the lid to pressurize the power adapter to 12 ± 2 psi

(0.828 ± 0.138 bar) and check for leaks.

NOTE: Another way to detect leaks is to submerge the canister in the

upright position in a tank of water. All joints, connections, and seams can be brushed with a mixture of liquid soap and water.

CAUTION: The pressure relief valve is set for 18−22 psi

(1.241−1.517 bar). Do not exceed 14 psi (.965 bar).

9. Repair leaks, if necessary.

Page 20

PA-3 Power Adapter (50 Hz/Oil-Filled) Parts

5. Parts

Using the Illustrated Parts List

Item Description Part Number Quantity Note

S1 Assembly xxxxxxxx 1 A

NS Part xxxxxxxx 1

H1 Part or Assembly

Part/Assembly for option 1 xxxxxxxx 2 Part/Assembly for option 2 xxxxxxxx 2

To order parts, call Siemens Airfield Solutions Customer Service or your local representative. Use this five-column parts list, and the accompanying illustration, to describe and locate parts correctly.

This subsection describes how to use the illustrated parts list covered later in this section. It does not provide the actual parts list.

The Item column numbers correspond to the numbers that identify parts in illustrations following each parts list. NS (not shown) indicates that a listed part is not illustrated.

The Description column gives the part name, as well as its dimensions and other characteristics when appropriate. Indentions show the relationships between assemblies, subassemblies, and parts.

The Part Number column gives the Siemens Airfield Solutions part number.

T1 Assembly xxxxxxxx 1

• Part

NOTE A

The Quantity column contains the quantity required per unit, assembly, or subassembly. The code AR (As Required) is used if the part number is a bulk item ordered in quantities or if the quantity per assembly depends on the product version or model.

The Note column contains letters that refer to notes at the end of each parts list. Notes contain special ordering or product/part version information.

xxxxxxxx 1 xxxxxxxx 2

Page 21

PA-3 Power Adapter (50 Hz/Oil-Filled) Parts

PA-3 Power Adapter (50 Hz)

The PA-3 power adapter (50 Hz) part number is 44B1545-1.

Part Number

PA-3 Power Adapter (50 Hz) Spare Parts

Item Description Part Number Quantity Note

NS Power transformer, PA-3, 300 W, 50 Hz 35A0285 1

Cap, 30 µF, 440 Vac, 10%, paper/oil

1 Valve, air fill 77A0091 1

2 Cord (P1) 70B0321 1

3 Cord grip (P1, J1) 77A0099 2

4 Cord, female (J1) 70A0323 1

5 Cord (J2) 70B0322 1

6 Cord grip (J2) 77A0100 1

See Figure 3. This subsection provides spare parts for the PA-3 power adapter (50 Hz).

20A0040 4

7 Valve, air relief 77A0092 1

NS: Not Shown

Figure 3. PA-3 Power Adapter (50 Hz) Spare Parts

Page 22

PA-3 Power Adapter (50 Hz/Oil-Filled) Wiring Schematics

6. Wiring Schematics

2.8-6.6 A Series Circuit

L-823 1-Pole Male Connector

L-823 1-Pole Female Connector

2.8-6.6 A Series Circuit

PA-3

300 VA

Power Adapter

See Figure 4. This section provides PA-3 power adapter (50 Hz) wiring schematic for internally lighted wind cones.

AWG 14, 300 V Minimum

120 Vac

L-823 2-Pole Male Connector

L-810 Obstruction Light

100 W 100 W

69 W

Figure 4. PA-3 Power Adapter (50 Hz) Wiring Schematic for Internally Lighted Wind Cones