Siemens MOBY series, MOBY E, MOBY D, MOBY U, MOBY F User Manual

...

Download

Page 1

Table of Contents

General

Commissioning the STG

Using the STG

The “MOBY D/E/F/I/U” Programs

The “FILEHANDLER” Program

Expanded Functions

The “MOBY D/E/F/I/U” Programs with the PSION Numeric Model

Error Messages

Technical Data

Appendix

Published in January 2004

(5)J31069-D0126-U001-A5.1-7418

User’s Guide

MOBY

STG Hand-Held Terminal

Page 2

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. These notices are highlighted in the manual by a warning triangle and are marked as follows according to the level of danger:

Note

draws your attention to particularly important information on the product, handling the product, or to a particular part of the documentation.

Qualified Personnel

The device/system may only be set up and operated in conjunction with this manual. Only qualified personnel should be allowed to install and work on this equipment. Qualified persons are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment, and systems in accordance with established safety practices and standards.

Correct Usage

Note the following:

Warning

This device and its components may only be used for the applications described in the catalog or the technical description, and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed correctly, and operated and maintained as recommended.

Trademarks

MOBYR is a trademark of SIEMENS AG. Some of the other designations used in these documents are also registered

trademarks; the owner’s rights may be violated if they are used be third parties for their own purposes.

We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual are reviewed regularly and any necessary corrections included in subsequent editions. Suggestions for improvement are welcomed.

The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.

Siemens AG Automation and Drives Group Division Special Products,

Projects Automotive Industry, Training

PO Box 4848, D-90327 Nuremberg

E Siemens AG 1999, 2000, 2002, 2003, 2004 Technical data subject to change.

Siemens Aktiengesellschaft Order No. (5)J31069-D0126-U001-A5.1-7418

Page 3

R 01.04

E-I

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Table of Contents

1 General E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Application Areas E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Product Description E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 FCC Information for the USA E-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Commissioning the STG E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Included Components E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Assembly E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Turning on the Device and Setting the Operating Mode E-6. . . . .

2.4 MOBY Applications E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 User Interface E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Using the STG E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Keyboard E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 Antenna on the Read Head and Antenna Field E-9. . . . . . . . . . . .

3.2.1 MOBY D/E/F/I E-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2.2 MOBY U E-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3 Using the MOBY U Antenna E-12. . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4 Charging Function E-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5 Changing the Battery Pack of the MOBY U Antenna E-16. . . . . . .

4 The “MOBY D/E/F/I/U” Programs E-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 Data Editor E-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 MDS Functions E-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.1 General Information on Read and Write-Accessing an MDS E-21.

4.2.2 Reading the MDS E-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.3 Writing the MDS E-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.4 Erasing/Initializing the MDS E-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.5 Reading MDS Status E-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.6 Reading the ID Number E-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.7 Reading OTP Memory E-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.8 Writing OTP memory E-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.9 Reading Raw Data E-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3 File Functions E-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.1 Loading a File E-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.2 Saving E-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

Page 4

R 01.04

E-II

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.3.3 Exiting E-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 The Editor Functions E-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1 Jump to Address E-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.2 Display E-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.3 Clear Display E-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.4 Edit Date E-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 The Extras Functions E-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.1 Communication E-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.2 Password E-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.3 Antenna E-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.4 Address Setup E-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.5 MOBY I Setup E-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.6 MOBY E Setup E-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.7 MOBY U Setup E-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.8 SLG Status E-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6 The “?” Functions E-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.1 Language E-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.2 About E-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.3 Version E-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 The “FILEHANDLER” Program E-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 General Information on the Filehandler E-36. . . . . . . . . . . . . . . . . . .

5.2 The Filehandler Commands E-37. . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 View of the Editor and Directory E-39. . . . . . . . . . . . . . . . . . . . . . . . .

5.3.1 The Data Editor of the Filehandler E-39. . . . . . . . . . . . . . . . . . . . . . .

5.3.2 View of the Directory E-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 The File Functions E-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.1 Read File from MDS (Read File from Tag) E-41. . . . . . . . . . . . . . . .

5.4.2 Read File from STG RAM E-42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.3 Write File to MDS (Write File to Tag) E-42. . . . . . . . . . . . . . . . . . . . .

5.4.4 Write File to STG RAM E-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.5 Read Directory from MDS (Read Dir from Tag) E-43. . . . . . . . . . . .

5.4.6 Read Directory from STG RAM (Read Dir from STG RAM) E-43.

5.4.7 Example: Copy Files E-44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 The Commands Menu E-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.1 New File (Create File) E-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.2 Delete File E-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.3 Format MDS (Tag Format) E-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.4 Attribute File (File Attribute) E-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.5 MDS Status (Tag Status) E-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

Page 5

R 01.04

E-III

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.5.6 MDS Cover E-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6 The Editor Functions E-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.1 Display Directory E-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.2 Display Editor E-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.3 Change File Size (File Size) E-49. . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.4 Delete Display (Clear Display) E-49. . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.5 Jump to Address E-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.6 Display Setup E-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7 The Extras Functions E-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.1 Parameter E-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2 Password for Filehandler (Password for FH) E-51. . . . . . . . . . . . . .

5.7.3 Communication E-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8 The “?” Functions E-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Expanded Functions E-52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Storing the MDS Data on the Hand-Held Terminal E-52. . . . . . . . .

6.2 Copying MOBY Data from and to the Hand-Held Terminal E-53. .

6.2.1 What Is Needed in Addition? E-53. . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2.2 Using the PSION File Manager E-53. . . . . . . . . . . . . . . . . . . . . . . . . .

6.2.3 Organization of the READ.HEX File E-56. . . . . . . . . . . . . . . . . . . . . .

6.2.4 Organization of the READ.HX1 File E-56. . . . . . . . . . . . . . . . . . . . . .

6.3 Functions with the PSION Operating System E-56. . . . . . . . . . . . . .

6.4 Parallel Execution of Several Applications E-57. . . . . . . . . . . . . . . .

6.5 Automatic Power Saver Function E-58. . . . . . . . . . . . . . . . . . . . . . . .

6.6 Connecting SIM Devices (MOBY E/I/V) E-58. . . . . . . . . . . . . . . . . . .

6.7 System RESET E-59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 The “MOBY D/E/F/I/U” Programs with the PSION Numeric Model E-60

8 Error Messages E-61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.1 Error Messages with the “MOBY D/E/F/I/U” Programs E-62. . . . . .

8.2 Error Messages with the “FILEHANDLER” Program E-66. . . . . . . .

9 Technical Data E-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A Appendix E-74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.1 Ordering Components for Expanded Functions E-74. . . . . . . . . . . .

A.2 Developing User Applications E-75. . . . . . . . . . . . . . . . . . . . . . . . . . .

A.3 ASCII Table E-80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

Page 6

R 01.04

E-IV

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Table of Contents

Page 7

R 01.04

E-1

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

1 General

The STG (service and test device) is a powerful addition to the MOBY D, MOBY E, MOBY F, MOBY I or MOBY U identification systems. It is a mobile hand-held terminal based on the PSION Workabout mx and is designed for applications in the areas of logistics, distribution and service. In addition, it is an indispensable aid when commissioning and testing.

1.1 Application Areas

The MOBY hand-held terminal can be used with MOBY D, MOBY E, MOBY F, MOBY I and MOBY U. The included service and test program makes it easy to read and write all data memories of MOBY D, MOBY E, MOBY F, MOBY I or MOBY U.

In addition, it is very simple for customers to program their own applications on the hand-held terminal. A C library is available from Siemens for programming the hand-held terminal read heads. Implementation of applications in the areas of warehousing, logistics and commissioning is easy. Very sturdy in design and protected against splashed water, the hand-held terminal can also be used in rugged environments. Its display is easy to read, and in dark areas, display illumination can be turned on.

1.2 Product Description

The MOBY hand-held terminal consists of a basic device and a read head from MOBY D, MOBY E, MOBY F or MOBY I or an antenna of MOBY U. The basic device is a PSION Workabout mx. This device is the worldwide standard for handheld terminals. In addition, the terminal includes a memory card with the MOBY service and test program including a user’s manual. The memory card is inserted in the basic device. The service and test program starts automatically when the hand-held terminal is turned on. All data memories of MOBY D, MOBY E, MOBY F, MOBY I or MOBY U can be processed with the hand-held terminal.

General

Page 8

R 01.04

E-2

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

The following functions can be executed.

S Read data from the MDS S Write data to the MDS S Delete the entire data memory (write with a filler value) S Read and display the ID number of the MDS (MOBY D/E/F/U) S Read MDS status (MOBY U) S Read data from OTP memory (MOBY U) S Write data to OTP memory (MOBY U) S Represent and edit the data in hexadecimal and ASCII format S Enable/disable password protection for all write-access functions and for

exiting the MOBY program

S Menu prompting in various languages (currently German and English) S Store read MOBY data in files. Approximately 1.8 MB are available for this

on the hand-held terminal.

Additional functions with the MOBY I filehandler

S Format the MDS S Create files on the MDS S Write files to the MDS S Read files from the MDS S Read and display the directory S Delete files from the MDS

The read/write head of MOBY D/E/F/I is screwed to the PSION basic device. The head is equipped with a serial TTL interface for communication with the basic device. The read head is powered by the basic device. The antenna of MOBY U and the PSION basic device are connected with a slide catch. Communication takes place via the RS 232 interface. The power supply of the antenna is provided by an integrated battery pack. The read/write head or the antenna and the STG program can also be ordered separately so that customers can continue to use an already existing PSION Workabout or order a Workabout with a different interface and keyboard configuration directly from PSION.

General

Page 9

R 01.04

E-3

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

The appropriate charging device (including 230 V plug-in power pack) for recharging the batteries must be ordered separately.

S MOBY D/E/F/I

The charging device (order number 6GT2 303-1DA00) is designed for mounting on walls or vehicles. When mounted on a vehicle, a special PSION cable is required for the charging function. See appendix A.1.

S MOBY U

The batteries of the hand-held terminal (in PSION Workabout and the antenna) are charged with the power pack (order number 6GT2 503-1DA00). See chap. 3.4.

For applications, a C library is available to the user with the functions of the MOBY read head. Users can develop their own programs (cf. appendix A.2) with the optional C development environment.

1.3 FCC Information for the USA

S PSION basic device – See PSION user’s manual. S MOBY E/I/U read head/antenna

Made in Germany SIEMENS MOBY STG FCC ID: KR5MIS

KR5MIS-I NXWMOBYU-STGU

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES: OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

(for MOBY E) (for MOBY I) (for MOBY U)

Note

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment: Such modifications could void the user’s authority to operate the equipment.

General

Page 10

R 01.04

E-4

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

2 Commissioning the STG

2.1 Included Components

The STG consists of several components which are listed individually on the delivery slip.

Ordered

Components

Order Number Pack List Pack Number

MOBY D

6GT2 603-0AA00 PSION Workabout

A5E00016735

hand-held

MOBY D read head 6GT2 603-1AA00

ermin

al STG

Memory card incl. STG software and user’s manual

6GT2 303-1CA00

NiCd battery 6GT2 094-0AB00

MOBY E

6GT2 303-0AA00 PSION Workabout

A5E00016735

hand-held

MOBY E read head 6GT2 303-1AA00

ermin

al STG

Memory card incl. STG software and user’s manual

6GT2 303-1CA00

NiCd battery 6GT2 094-0AB00

MOBY F

6GT2 403-0BA00 PSION Workabout

A5E00016735

hand-held

MOBY F read head 6GT2 403-1BA00

ermin

al STG

Memory card incl. STG software and user’s manual

6GT2 303-1CA00

NiCd battery 6GT2 094-0AB00

MOBY I

6GT2 003-0CA00 PSION Workabout

A5E00016735

hand-held

MOBY I read head 6GT2 003-1CA00

ermin

al STG

Memory card incl. STG software and user’s manual

6GT2 303-1CA00

NiCd battery 6GT2 094-0AB00

Commissioning the STG

Page 11

R 01.04

E-5

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Ordered

Components

Pack NumberPack ListOrder Number

MOBY U

6GT2 503-0AA00 PSION Workabout

A5E00016735

hand-held

MOBY U antenna 6GT2 503-1AA00

ermin

al STG

Memory card incl. STG software and user’s manual

6GT2 303-1CA00

NiCd battery 6GT2 094-0AB00

2.2 Assembly

Perform the following steps in the order shown below.

S Install button cell. Button cell is located in a recess in the packaging of the

PSION Workabout.

S Insert batteries. The battery catch must point to the left. S Insert the flash program memory with the STG application in the upper

slot (A).

S Install read head, and screw down (MOBY D/E/F/I). S Join antenna and PSION Workabout (MOBY U).

– Screw the PSION Workabout to the metal frame with 4 screws. – Plug the submin D plug of the MOBY U antenna into the RS 232 interface

of the PSION Workabout and screw down.

– Slide the PSION Workabout on the guide rail of the upper housing shell of

the antenna until the lock snaps in.

Assembly is complete.

Commissioning the STG

Page 12

R 01.04

E-6

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

2.3 Turning on the Device and Setting the Operating Mode

Note

Before you turn on the device, insert the hand-held terminal in the charging device (MOBY D/E/F/I) or connect to the power pack (6GT2 503-1DA00) (MOBY U) and allow it to charge for at least 14 hours.

After charging, the hand-held terminal is ready for use. After the terminal is turned on, initial startup takes several seconds. The MOBY

application then starts automatically, and a selection menu appears with the MOBY applications. Select the MOBY application for the RF read/write head or the antenna which you want to use.

1) MOBY filehandler for MOBY I The MDS data are accessed by file names. See chapter 5.

2)-6)Normal MOBY service and test program for MOBY D/E/F/I/U. The MDS data are accessed by physical addresses. See chapter 4.

9) The operating system of the hand-held terminal is accessed with “Exit.”

V) Version indication in MOBY application

menu (not shown in selection menu)

The device goes off automatically after no keys have been pressed for 5 minutes. When turned on again, the hand-held terminal continues with the same screen it was displaying before it was turned off manually or automatically. See chapter 6.5.

Commissioning the STG

Page 13

R 01.04

E-7

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

2.4 MOBY Applications

If you use a different read head (MOBY D/E/F/I) or the MOBY U antenna with the hand-held terminal later on, you will have to change the MOBY application. Exit the running application with the FILE/EXIT menu. The PSION start screen appears. Confirm this screen with ENTER. Then select the required MOBY application in the next screen which appears.

2.5 User Interface

Use of the STG programs MOBY D/E/F/I/U on the hand-held terminal is described in chapter 4.

Use of the Filehandler program for MOBY I is described in chapter 5. All functions of the MOBY programs can be called with the “Menu” key.

Commissioning the STG

Page 14

R 01.04

E-8

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

3 Using the STG

3.1 Keyboard

The keyboard of the PSION is divided into 3 parts.

S 11 control keys directly below the display S Numerical key block with 16 keys S ASCII keyboard (30 keys) including shift key

ASCII keyboard plus shift and special function keys (Ctrl, )

Control keys: Contrast, display illumination, on/off, and cursor keys

Numeric input block with Enter key

Green LED. Goes on when battery is being charged.

Using the STG

Page 15

R 01.04

E-9

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

3.2 Antenna on the Read Head and Antenna Field

3.2.1 MOBY D/E/F/I

The antenna of the read head is located on the top of the hand-held terminal as shown in the figure below.

Reading an MDS

The various types of MDSs offer different ranges. The following table gives you an overview.

MOBY D MOBY E MOBY F MOBY I

MDS Type mm MDS Type mm MDS Type mm MDS Type mm D139 60 E600

(ISO card)

18 F125 80 402/401 6

D160 25 E611 30 F415 50 404/514/413E 20

Labels based on

E624 (button) 8 F124 60 403 8

Basis I-Code:

E623 (pill)

4/3

506 12 I-Code1 75 439E 12 I-Code SLI 100 507

Tag-it HF-I 100

(with battery)

my-d 100 507 (without

battery)

1 The pill can only be read on the head portion provided for this. 2 When MDS is installed in metal 3 Range tolerances are to be expected for manufacturing reasons. The distances apply

to labels with the size 85 x 55 mm.

Using the STG

Page 16

R 01.04

E-10

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Example: MDS E600

Example: MDS E623

MOBY D/E/F

MOBY E/I

Button antenna or rod antenna (MOBY I)

Surface antenna

The antenna field for the STG read head

Antenna field for MOBY E

With the MOBY E read head, 2 antennas are integrated in the reader. These must be positioned on the read head based on which MDS you want to read. The EXTRAS/ANTENNE command (see chapter 4.5.3) is used to switch the antenna field. Remember that the MDS E623 can only be read on the antenna provided for this. See figure. The MDS E624 can be read on both the button antenna and the surface antenna.

Using the STG

Page 17

R 01.04

E-11

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

3.2.2 MOBY U

The actual antenna of the STG U hand-held terminal is located on the back of the MOBY U antenna (see photo below). This means that the direction of emission is vertical to the back of the MOBY U antenna. The cone-shaped antenna field has an opening angle of approx. 90 degrees. The maximum field length (limit distance) is 3 meters. It can be set in increments of 0.5 m in the “Extras” menu.

Back of the MOBY U antenna

Antenna

Using the STG

Page 18

R 01.04

E-12

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

3.3 Using the MOBY U Antenna

The MDS functions (e.g., read, write, initialize) are not triggered on the STG U hand-held terminal until the communication button is pressed.

The “Menu” button is used to select the appropriate MDS function. The following message appears on the display.

ESC to cancel

Wait for ENTER of antenna

Then point the STG U hand-held terminal to the desired MDS Uxxx and press the communication button. After the communication button is pressed, the antenna goes on, the MDS function is executed, and the antenna goes off again. As long as the antenna is active, the LED for communication is yellow. It takes approx. 2 seconds to turn on the antenna. Depending on the amount of data and the recognition of the MDS, turn on takes a minimum of approx. 3 seconds.

STG U hand-held terminal

LED for communication

Communication button

Note

The LED communication lights up red when the charging status of the batteries is not sufficient for communication.

Using the STG

Page 19

R 01.04

E-13

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

3.4 Charging Function

The battery charging procedure is started as soon as the PSION Workabout is placed in the wall or vehicle holder. Charging is activated and indicated with a green LED. See chapter 3.1. When the batteries are empty, at least 14 hours are required for a complete charge.

High-speed battery charging

The batteries supplied by Siemens for the PSION Workabout can be charged at high speed so that the MOBY hand-held terminal can be operated directly in the high-speed charging device available from PSION. A full charge takes 1 hour.

Use of other batteries

Other AA batteries can also be used in the PSION Workabout. These include rechargeable NiCd batteries and alkali batteries which cannot be recharged.

IMPORTANT: Be sure to adhere to the PSION user’s manual.

The backup battery

The backup battery in the PSION Workabout is used to retain the application data when the main batteries are empty. The backup battery is a lithium cell which cannot be charged. Remember that, when the main batteries are empty or have been removed, a new backup battery can only maintain the data in the RAM for just a few days.

Using the STG

Page 20

R 01.04

E-14

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Charging STG U hand-held terminal

The batteries of the STG U hand-held terminal (in the PSION Workabout and the MOBY U antenna) can be charged with only one power pack (6GT2 503-1DA00).

The STG U hand-held terminal with connected power pack for charging the batteries

LED for charging the batteries

Charging socket of the PSION Workabout

Plug for the charging adapter

Charging socket of the MOBY U antenna

Cable switch on the charging cable

Charging cable Power pack

Charging adapter for the PSION Workabout

Proceed as shown below to connect the power pack to charge the batteries.

S Plug charging adapter into the charging socket of the PSION Workabout. S Plug connector on the cable switch of the charging cable into the charging

socket of the MOBY U antenna.

S Plug connector for charging adapter on the charging cable into the charging

adapter.

S Connect power plug of the power pack.

The charging status of the battery pack of the MOBY U antenna is indicated by the LED for charging the batteries.

S Yellow: The battery pack of the MOBY antenna is being charged. S Green: The battery pack of the MOBY antenna is charged. S Red: The device is defective.

On the PSION Workabout, a green LED (see chap. 3.1) is on during charging.

Using the STG

Page 21

R 01.04

E-15

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

When batteries are empty, duration of charging is:

S At least 1.5 hours for the MOBY U antenna S At least 14 hours for the PSION Workabout.

The STG U hand-held terminal can also be used during charging.

Note

S The PSION Workabout can only be charged when it is equipped

with original PSION batteries.

S A restricted temperature range must be adhered to when the bat-

tery pack of the MOBY U antenna is being charged: 0 °C to +40 °C.

Using the STG

Page 22

R 01.04

E-16

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

3.5 Changing the Battery Pack of the MOBY U Antenna

The battery of the MOBY U antenna is a lithium ion battery pack. It has a lifespan of approx. 500 charging cycles. When the capacity of the battery pack has decreased to the point that the operating time of the MOBY U antenna is no longer sufficient for the application, it is time to replace the battery pack. Disconnect the 9 screws on the back of the housing shell of the antenna and remove the shell. Replace the battery pack. Replace the housing shell and screw it tight.

Note

S The power pack may not be connected on the STG U hand-held

terminal while the battery pack is being replaced.

S The PSION Workabout does not need to be separated from the

MOBY U antenna although it must be turned off during replacement.

Note

The replacement battery pack for the MOBY U antenna has the order number 6GT2 594-0AB00.

Warnung

The battery pack of the MOBY U antenna and the replacement battery pack consist of lithium ion batteries. The following must be adhered to when handling these batteries.

S Avoid risk of fire, explosion and severe burns. S Do not expose the battery pack to temperatures in excess of

100 °C.

S Do not take the battery pack apart or destroy it.

Incorrect handling, damage or contact with water may cause the battery pack to explode.

S Adhere to national regulations when disposing of used recharge-

able batteries/batteries.

Using the STG

Page 23

R 01.04

E-17

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4 The “MOBY D/E/F/I/U” Programs

After you turn on the STG, the editor appears on the display. You can view the data, enter new data or call a function with the “Menu” key. Functions can also be called directly with the key. To do this, press the key and the appropriate alphanumeric key at the same time. The table below lists all functions together with their direct calls.

Command Shortcut Description

File/Load File L or F3

Load file from PSION RAM drive to working storage

File/Save S or F4

Store read MDS data on the RAM drive File/Exit X Exit STG application Tag/Read R or F1

Read data from MDS Tag/Write W or F2

Write data to MDS Tag/Erase/initialize E Write MDS with a certain value Tag/Tag status O

Read MDS status Tag/Read TagId T Read ID number of MDS Tag/Read OTP F

Read data from OTP memory Tag/Write OTP H

Write data to OTP memory Tag/Read raw data M

Read physical memory of MDS Editor/Jump to address J or Tab Jump to a certain address in editor Editor/Display D Change display options Editor/Clear C Clear data in editor to a certain value Editor/edit date A The date on which the cursor is posi-

tioned can be edited in a number of for-

mats. Extras/Communication I Change communication options Extras/Password for STG P Change password for STG application Extras/Address Setup G Define entries for the “read/write MDS”

commands Extras/MOBY I Setup H Set memory size and MOBY I operating

mode

The “MOBY D/E/F/I/U” Programs

Page 24

R 01.04

E-18

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Command DescriptionShortcut

Extras/MOBY E Setup Y Switch MDS access from “MOBY key” (A)

to the B key

For MOBY E SIM: Switch between cyclic

operation and continuous operation Extras/MOBY U Setup K

Define MDS memory size and range limit Extras/SLG status Q

Read status of MOBY U antenna ?/Language N Set menu language ?/About... B Manufacturer’s data ?/Version V Version of operating system and STG

application

1 These keys are only available on a hand-held terminal with a numeric keyboard. 2 Not MOBY U 3 Only MOBY U

The “MOBY D/E/F/I/U” Programs

Page 25

R 01.04

E-19

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.1 Data Editor

The MDS data can be edited in hexadecimal or ASCII in the editor screen. This can be set in the EDITOR/DISPLAY menu.

The editor always shows the total size of an MDS memory. Use the cursor functions to access the individual addresses. Use the “Tab” key to jump to any address. See chapter 4.4.1.

Indication of the currently set read head. Cf. chapter 4.5.1

The TagId of the MDS is only displayed on the MOBY E/F/D/U. It is valid after the “MDS/read-write-readTagId” function is executed.

Date field: The date on which the cursor is located can also be shown in hexadecimal, decimal, ASCII or binary format. The “Editor/edit date” function can be used to change the value in the date field.

The editor screen contains the MDS date. Standard setting is 32 bytes.

MDS addresses are shown in hexadecimal or decimal format.

The “MOBY D/E/F/I/U” Programs

Page 26

R 01.04

E-20

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

The “current area”

Current area

The editor uses normal representation for the “current area.” All other data areas of the MDS are shown inverted. The current area shows the data block which was read last. During read/writeaccesses, the current area is entered as the value for the write command. This value can be adjusted in the TAG/WRITE or TAG/READ menu.

The current area is changed automatically when you edit data and overwrite.

The size of the memory area shown on the display can be switched with the EDITOR/DISPLAY function. See chapter 4.4.2.

In the normal representation, 32 bytes are displayed in lower case letters. This gives you an overview of the MDS data.

In zoom representation, only 4 consecutive bytes are shown. Representation is in upper case letters. This display is easy to read.

Zoom representation (hexadezimal)

Zoom representation (ASCII)

The “MOBY D/E/F/I/U” Programs

Page 27

R 01.04

E-21

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.2 MDS Functions

After a command is started, a window with a bar appears on the display. This bar shows how much of the command has already been processed.

The MDS functions handle communication with the MDS. The MDS function is not interrupted if you briefly move the MDS out of the read field. The MDS function is terminated if MDS processing does not take place for more than 30 seconds. See chapter 4.5.

4.2.1 General Information on Read and Write-Accessing an MDS

The MOBY D, MOBY E and MOBY F MDSs use block-oriented data accessing. A read or write-access to an MDS is only possible at the beginning of a block. One block contains 16 bytes (or 10 hex) with MOBY E/F. Thus, the start addresses for MDS processing to be entered on the STG are: 00, 10, 20, 30 hex and so on. With MOBY D a block has a length of 4 bytes (I-Code, Tag-it) or 8 bytes (my-d). The start addresses are: 00, 04, 08, 12 hex ... (I-Code, Tag-it) or 00, 08, 10, 18 hex ... (my-d). With the MOBY D/E/F/U, the TagId on the display is automatically updated to the current value after the read/write access.

The “MOBY D/E/F/I/U” Programs

Page 28

R 01.04

E-22

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

However, you can also specify any start address. This will be accepted by the STG and corrected to the next lower block beginning. The corrected address is indicated for the operator in a window and must be acknowledged.

An additional window appears if you change data in the editor and then attempt to read an MDS. The window tells you that the data which you have just modified may be overwritten again with the “read MDS” command. You can retain or reject the modified data in the editor, or you can terminate the command completely.

Note

ECC mode can only be set on the MOBY I hand-held terminal. ECC mode cannot be used with MOBY D/E/F/U.

4.2.2 Reading the MDS

A data block with a start and end address, which can be defined as desired, can be read from the MDS. If the same value is entered for the start and end address, only one block can be read from the MDS. The address area is indicated in another screen for confirmation.

Note

If mode “Complete MDS” was selected in the read/write field of the menu “Extras/Address Setup/...,” the “MDS/read” funktion is started immediately without asking any questions. The complete MDS is always processed.

The “MOBY D/E/F/I/U” Programs

Page 29

R 01.04

E-23

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.2.3 Writing the MDS

A data block can be written to the MDS. The data block which is valid in the editor is indicated as the default for each write access. The default length or end address can still be changed to another value during the write-access.

4.2.4 Erasing/Initializing the MDS

The “erase/initialize MDS” function is used to write the entire MDS with a certain value in a very short time. The erasure value can be entered in a subsequent menu. After the deletion function has been performed, the memory in the editor is also erased with the value which was entered. With the MOBY I/U, the correct size of the MDS memory must be set (Extras/MOBY I Setup or Extras/MOBY U Setup) before this function is performed.

The “MOBY D/E/F/I/U” Programs

Page 30

R 01.04

E-24

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.2.5 Reading MDS Status

Only MOBY U: The function reads the status data from the MDS and indicates it.

MDS status information

S MDS number (8-position, hexadecimal format) and MDS memory size (2 or

32 kB)

S Data for calculation of the battery lifespan (total accesses, total search, and

change sleep time)

S Remaining battery life time of the MDS in % S Sleep time set on MDS

Note

For calculation of the battery lifespan of the MOBY U data medium, it is essential that the STG software have the current calendar week and the current calendar year. This is the reason the date must be set correctly on the PSION Workabout. The date can be set via the system menu “Time” → “Time and date.”

Proceed as shown below.

S Exit the MOBY U service and test program via “File/Exit.” S Select “System screen.” S Position the cursor on the application “IMG.” S Click the “Menu” button. S Select “CTRL/Set time and date.” S Set “Time” and “Date” and accept with “Enter” button. S Return to the MOBY U service and test program via “IMG” and

“Moby_u[A].”

The “MOBY D/E/F/I/U” Programs

Page 31

R 01.04

E-25

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.2.6 Reading the ID Number

Only MOBY D/E/F/U: The function reads and indicates the serial number of the MDS. The ID number is set at the factory and cannot be changed. The TagId is displayed in hexadecimal format by the editor in the second line. The TagId is automatically read with the “MDS read/write/erase” functions.

4.2.7 Reading OTP Memory

Only MOBY U: The function reads the complete OTP memory (16 bytes).

Note

When the mode “MDS complete” was selected in the “Read/write” field in the “Extras/Addresses Setup/...” menu, the function “MDS/ Read” is started immediately without any further questions. The entire MDS is always processed.

4.2.8 Writing OTP memory

Only MOBY U: The function writes the complete OTP memory (16 bytes).

Note

The OTP memory can be written only once. Before execution, you are asked again whether you really want to execute the function since this action is irreversible.

The “MOBY D/E/F/I/U” Programs

Page 32

R 01.04

E-26

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.2.9 Reading Raw Data

Only MOBY D/E/F: This function is used to physically read the entire memory of the MDS. This includes TagId, key information (if public), manufacturer’s information and MDS access rights. A knowledge of the physical layout of the MDS memory is required to interpret the data. See description of MFWAPI or CCTWAPI.

The “read raw data” function can be used to detect errors made when the MDS was configured.

Note

For MOBY F

MDS addresses 8 to 3F hex (i.e., pages 2 to 15) cannot be read. They are always shown by the editor as 00.

The “MOBY D/E/F/I/U” Programs

Page 33

R 01.04

E-27

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.3 File Functions

4.3.1 Loading a File

A file can be loaded to the STG editor which was

S saved before with the “file/save” command or S transferred from the PC to the “RAMDRIVE (M:)” drive of the PSION. See

chapter 6.2.

4.3.2 Saving

Data currently being displayed by the editor can be saved in a file on the PSION. The file name may consist of 1 to 8 letters or numbers. During the storage procedure, the extension “.HEX” (data) and “.HX1” (ID no.) is automatically added to the file name. See also chapter 6.2.

A memory area of approximately 1.8 Mbytes is available on the hand-held terminal for storage of MDS data (i.e., with MOBY E, up to 2000 MDSs can be read and stored).

4.3.3 Exiting

The “exit” function can be used to conclude the STG program of MOBY. This gives you access to the operating system levels of the PSION hand-held terminal. See chapter 6.3.

The “MOBY D/E/F/I/U” Programs

Page 34

R 01.04

E-28

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.4 The Editor Functions

4.4.1 Jump to Address

You can enter a memory address in decimal or hexadecimal format. The setting can be changed under menu item Display/Display Address. This address will then be represented by the editor as the start address.

This function can also be triggered directly in the editor with the “Tab” key.

4.4.2 Display

The following settings are available in this menu.

S Switch the editor between 32-byte representation (i.e., 4x8= fine-print

display) and 4-byte representation (i.e., 1x4= large, easy-to-read characters).

S No address is displayed for editor representation 1x5. This display is very

good when reading fixed-code MDSs with the MOBY F. With other MDS types, the first 5 bytes of the read data are displayed. You cannot change to other addresses with the cursor.

S Switch the editor between hexadecimal and ASCII representation. The

addresses are always shown in hexadecimal or decimal format.

S Switch date between “BIN,” “ASCII,” “DEC” and “HEX” format.

The “MOBY D/E/F/I/U” Programs

Page 35

R 01.04

E-29

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.4.3 Clear Display

The “clear display” function is used to overwrite the entire memory in the STG editor with a value which you can specify. You can then change the desired data to the appropriate values in the editor. No function is performed on the MDS.

S The data field can be shown in hexadecimal, ASCII, decimal or binary for-

mat. The data can also be changed with the “Indicate/edit date” function with the format set here.

S The addresses can be indicated in hexadecimal or decimal.

4.4.4 Edit Date

In addition to the standard formats hex and ASCII of the editor screen, the “edit date” function also provides the decimal and binary formats for data entry.

The “MOBY D/E/F/I/U” Programs

Page 36

R 01.04

E-30

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.5 The Extras Functions

4.5.1 Communication

S Interface Switching between the TTL interface (read head) and the

RS 232 interface takes place here.

If the RS 232 setting is used, the protocol must be set to “MOBY E/SIM” or “ASM 420/I/V.”

No setting is required for MOBY U. The interface is permanently set to RS 232.

S Protocol Certain protocols can be set here depending on which read

head is being used.

Read Head Protocol That Can Be Set

MOBY D MOBY D ISO

MOBY E MOBY E/SIM

MOBY I ASM 420/I/V

MOBY D

MOBY E

MOBY I

When the MOBY protocol is set, the memory size of the editor

is also automatically specified for MOBY E/F.

With MOBY I, the memory size of the editor is set with the “Extras/MOBY I Setup” function. The 3964R protocol is permanently set for MOBY U. The memory size of the editor is set with the “Extras/MOBY U Setup” function.

The “MOBY D/E/F/I/U” Programs

Page 37

R 01.04

E-31

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.5.2 Password

A password can be programmed as an option. The password must be entered prior to a write-access function. Once entered, a password remains valid until the STG is turned off (i.e., the password only has to be entered once during several consecutive write commands). The “MOBY” program can also only be exited with the password.

Default password

On delivery, the password is “123.” This password is also set after you remove the batteries of the STG.

Forgot the password?

If a password is forgotten, there is no way to obtain it again. The only solution is to remove the main battery and the button cell from the PSION for a few minutes. After the batteries have been re-installed and the device has been turned on, the STG assumes its status on delivery (i.e., the password is “123”).

Password 99999999

Changing the password to 99999999 (i.e., eight 9s) has a special purpose. The write-access function to the MDS and the “file/exit” function can no longer

be executed. The password can also no longer be changed. The only way to access the write-access function again is to remove all batteries. See also “forgot the password?”.

4.5.3 Antenna

Only for MOBY E: The antenna field on the read head is switched between “card” (large antenna) and “button” (small antenna). See also chapter 3.2.1.

The antenna must be set once when the read head is commissioned. The set antenna is retained on the read head when the hand-held terminal is turned off.

The “MOBY D/E/F/I/U” Programs

Page 38

R 01.04

E-32

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.5.4 Address Setup

This function defines the call of the “read/write MDS” commands.

S Start address + Length: Entry of the MDS address for the read/

write command uses a start address and the length of the data to be processed.

End address: Entry of the MDS address for the read/

write command uses a start address and an end address.

S Read/Write Switching from “block” to “complete MDS” takes place

here. This setting affects the default setting for execution of an MDS command. Block: When an MDS is read/written, the

currently active area is always indicated

as the area to be read/written.

Complete MDS: When an MDS is read/written, the

entire MDS is always processed. The read/write function is started immediately. Partial MDS areas cannot be entered.

The “MOBY D/E/F/I/U” Programs

Page 39

R 01.04

E-33

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.5.5 MOBY I Setup

S Mem size: Specifies the memory size of the MDS to be processed

This setting also defines the memory area in the editor. MDS memory addresses which exceed the memory size cannot be addressed.

S Tag type: Distinguishes between RAM/FRAM and EEPROM

The RAM/FRAM setting shows an empty MDS support

battery on the STG.

S ECC: Turns the ECC driver on and off

The purpose of the ECC driver is described in the documentation of the MOBY interface.

S MDS507: This parameter must only be set to “yes” when the

MDS 507 is used. With the MDS 507, the dialog battery is scanned and indicated as “Status” when it is empty.

S Sample rate: The scan time is only relevant when the MDS 507 is

used with an ASM 420. The setting range is 0.1 sec to

6.3 sec. The default value (0.5 sec) usually does not have to be changed.

4.5.6 MOBY E Setup

S Key A/B: You can switch between the “MOBY key” and the

“B transport key for MIFARE data memory.” The MOBY key is always standard. The “B” setting permits the MIFARE MDS to be processed in its status on delivery. (The B key must be in its original state.)

S Mode: Only for MOBY E SIM (cf. chapter 6.6):

Switches the SIM from cyclic mode to continuous mode. Command processing is much faster in continuous mode.

S Antenna: You can switch between card and pill.

The “MOBY D/E/F/I/U” Programs

Page 40

R 01.04

E-34

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

4.5.7 MOBY U Setup

S Memory size: Specify memory size of the MDS to be processed. This

setting can also be used to specify the memory area in the editor. MDS memory addresses beyond the memory size cannot be accessed.

S Standby time: The standby time can be set in increments of 7 msec

from 0 msec to 1400 msec. The default value (OFF) usually does not have to be changed.

S Working range The field length (limit distance) is 3 m. It can be set in

limitation: increments of 0.5 m to avoid excess working ranges for

the antenna. The setting range is between 0.5 m and 3.5 m. The default value is 1 m.

4.5.8 SLG Status

Only MOBY U: The SLG Status function can be used to read version states and settings of the MOBY U antenna. The information can be accessed with the “Enter” key in 3 consecutive screens.

S Screen 1: Hardware, firmware and loader version S Screen 2: Driver model, driver version and interface parameters S Screen 3: Set working range limitation, standby time and multitagging

(equals 1)

The “MOBY D/E/F/I/U” Programs

Page 41

R 01.04

E-35

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

4.6 The “?” Functions

4.6.1 Language

German or English can be selected as the menu language with the STG. During commissioning of the STG, the default language is English.

4.6.2 About

Information on the manufacturer of the STG program: Siemens AG A&D PT7 M2

4.6.3 Version

Specifies the version of the STG program, the EPOC operating system, the release status of the ROM version and the release status of the MOBY library. These parameters must be specified when reporting errors to Siemens.

The “MOBY D/E/F/I/U” Programs

Page 42

R 01.04

E-36

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5 The “FILEHANDLER” Program

5.1 General Information on the Filehandler

As with any PC-based system, the filehandler accesses the data with logical file names and not with physical memory addresses.

The following figure shows the layout of the “FILEHANDLER” program and how it works.

File 3.hex

File 2.hex

File 1.hex

MOBY\File 3.hex

MOBY\File 2.hex

MOBY\File 1.hex

Optional connection on the PC

WORD EXCEL

. .

Editor display

Directory display

Files on MDS

Files on hand-held terminal

File 3

File 2

File 1

The “FILEHANDLER” program is designed so that you can use the same functions to access the files on the hand-held terminal and the files on the MDS. The directory display is available for both the hand-held terminal and the MDS. MDS files can be copied from the MDS to the hand-held terminal (and vice versa) with just a few keys.

An optional connection to the PC (3link cable, see appendix A.1) permits you to exchange files stored on the hand-held terminal with the PC.

You can then process the data with your familiar PC programs (e.g., WORD, EXCEL, and so on). Prerequisite: The PC application must support the contents and data structure of the MDS file. See also chapter 6.

The “FILEHANDLER” Program

Page 43

R 01.04

E-37

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Note

Remember that the filehandler is only available for the MOBY I.

5.2 The Filehandler Commands

STG Command Shortcut

Filehandler

Command

Description

File/Read File from Ta g

R or F12, or Enter

READ Read a file from the MDS

File/Read File from STG RAM

S or F3

– Read a file from the RAM of

the hand-held terminal

File/Write File to Tag W or F2

WRITE Write a file to the MDS

File/Write File to STG RAM

T or F4

– Write the data from the editor

to the hand-held terminal

File/Read Dir from Tag G DIR Read directory from the MDS

and indicate

File/rRad Dir from STG RAM

P – Indicate directory of the STG

(RAM memory) File/exit X – Exit filehandler application Commands/Create

File

B CREATE Create new file with length of

0 on the MDS Commands/Delete File D or Del

DELETE Delete file from the MDS

Commands/Tag Format

I FORMAT Format the MDS

Commands/File Attribute

Y ATTRIB Assign access rights to file

on the MDS Commands/Tag Status F MDS STATUS Read MDS status Commands/Cover Tag C COVER Protect data structure of the

MDS Editor/Display Direc-

tory

Q – Display last read directory

Editor/Display Editor U – Display file data Editor/File Size N – Change file size in editor

The “FILEHANDLER” Program

Page 44

R 01.04

E-38

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

STG Command DescriptionFilehandler

Command

Shortcut

Editor/Clear Display J – Write display with certain

value Editor/

Jump to address

O or Tab – Move cursor to address posi-

tion Editor/Display Setup H – Switch display between

ASCII and HEX representa-

tion Extras/Parameter Z – Set filehandler parameters Extras/Password for

A – Password setting for the

“FILEHANDLER” program Extras/Communication E – Setting: Read head or ASM ?/Language L – Set menu language ?/About... K – Manufacturer’s data ?/Version V – Version of operating system

and filehandler

1 The key combination + key is used for the shortcuts of the commands. Both keys

must be pressed at the same time. The keys for the shortcuts of the MDS commands

are the same as the letters used to address them in the SIMATIC with FC. 2 Keys F1 to F4 are only available on a hand-held terminal with a numeric keyboard. 3 The

“Del” key can be used to delete the file currently selected in the directory view.

This can also be used to delete files from the RAM of the hand-held terminal.

The “FILEHANDLER” Program

Page 45

R 01.04

E-39

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.3 View of the Editor and Directory

The filehandler’s monitor screen display is either “Directory – View” or “Editor – View.” You can use the menu “Editor/Display Editor” and “Editor/Display Directory” menu to switch between the two displays.

5.3.1 The Data Editor of the Filehandler

The design of the data editor of the filehandler is similar to the standard STG program. See chapter 4.1.

Set MDS memory size. It can be set with the command Extras/Parameter.

Name of the file in the editor. The file can have been read by both the MDS and the hand-held terminal memory.

The piece of data on which the cursor is located. Is also shown in ASCII format.

The file length is shown here.

The data area which is longer than the file length is marked with the data string

“eof” (end-of-file).

If the file size is too long (see chap. 5.6.3), the extra data are shown inverted.

The “FILEHANDLER” Program

Page 46

R 01.04

E-40

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.3.2 View of the Directory

The directory view shows either all files of the MDS or all files of the STG RAM. The directory view makes it very easy to read files from the MDS or copy files between hand-held terminal and MDS. See chapter 5.4.

Layout of the directory

Indication of whether the displayed directory is from an

“MDS” or from the

“hand-held terminal”

Name with which the MDS was formatted. No name is indicated for the hand-held terminal’s directory.

Free memory on the MDS. With the hand-held terminal, this is approx.

1.8 MB (after the terminal has been commissioned).

A file can be selected with the cursor keys. After selection, a function can then be directly executed with this file. See chapter 5.4.

An attribute can be entered here for the MDS files (see chap. 5.5.4). No attributes can be set for hand-held terminal files.

The “FILEHANDLER” Program

Page 47

R 01.04

E-41

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.4 The File Functions

The file menu primarily contains three functions which can be called.

S Read file S Write file S Read and display directory

These functions can be executed on both the MDS and the internal memory of the hand-held terminal.

5.4.1 Read File from MDS (Read File from Tag)

After this function has been called, a menu appears in which you can select a file with the cursor keys. All file names can be scrolled through, including the ones in the directory view (see chap. 5.3.2).

After you have scrolled through all the files, the file name “New Tag DIR” appears. If you press the Enter key, the filehandler reads a directory from an MDS. You can then select one of the new files

If you continue paging through the file selection menu until the file name “Other File” appears, you can enter a file name (with the ASCII keyboard of the hand-held terminal) in the menu which appears.

The “FILEHANDLER” Program

Page 48

R 01.04

E-42

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.4.2 Read File from STG RAM

After this function is called, a menu appears in which you can select a file with the cursor keys. All file names in the RAM of the hand-held terminal with the file extension .HEX are displayed. If the STG RAM does not contain any files with the extension .HEX, the message “No file available” appears.

5.4.3 Write File to MDS (Write File to Tag)

The file name is entered as described in chapter 5.4.1. After a file name contained in the directory is entered, you are given the following choices.

You can overwrite the file or append the new data to the existing file.

In the next screen, you can still change the length of the data to be written.

The default length is always given as the value of the length of the data in the editor. If you change the default length, the data length on the MDS will also be adjusted.

If you selected the “Append” data option, the file is automatically read again after execution of the write function. This gives you the complete updated file on the editor.

If you selected the file name “Other File” when you called the write function and entered a new file name with the keyboard, the “Create” screen appears.

If you confirm this screen with “Yes,” a new file is created on the MDS before the data are written to the MDS.

The “FILEHANDLER” Program

Page 49

R 01.04

E-43

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.4.4 Write File to STG RAM

When a file is saved, the file name indicated in the editor is also indicated as the default name. You can still change the file name before saving the file. The file name may contain up to 8 characters. When the file is saved, the file extension .HEX is automatically added to the file name.

5.4.5 Read Directory from MDS (Read Dir from Tag)

The file directory of an MDS is read and indicated on the display in the directory view (see chap. 5.3.2). With some MDS types, this may take several seconds.

5.4.6 Read Directory from STG RAM (Read Dir from STG RAM)

The file directory of the hand-held terminal’s RAM (drive M:) is read and indicated on the display in the directory view (see chap. 5.3.2). Only type *.HEX files are shown on the display. Also, only files located in the root directory of the hand-held terminal’s RAM are indicated on the display.

The “FILEHANDLER” Program

Page 50

R 01.04

E-44

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.4.7 Example: Copy Files

The functions described in this chapter make it very easy to copy files. Files can be copied from MDS to MDS or from STG RAM to MDS. The procedure for copying a file from a first MDS to a second MDS will now be described:

1. The function “File/Read Dir from Tag” (

+ G) is executed.

4. The “Editor/Display Directory” function ( + Q) is executed.

5. The cursor keys

  select the file

to be written.

6. The “File/Write File to Tag” function ( + W) is executed.

After these functions have been executed, the “delivery” file is copied to “colour.” The “colour” file now also appears with a size of 300 bytes.

3. Press “Enter”. After being read, the data are displayed in the editor screen.

2. The cursor keys   select the file to be read.

The “FILEHANDLER” Program

Page 51

R 01.04

E-45

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.5 The Commands Menu

The “Commands” menu contains only commands related to the MDS memory.

5.5.1 New File (Create File)

“Create File” is used to set up a new file on the MDS. The file name may not yet exist on the MDS. The new file is always given a length of 0.

5.5.2 Delete File

This function deletes a file from the MDS memory. If you are in the directory view, it is very easy to start the delete function by

pressing the “Del” key. You can use the “Del” key to delete files from the MDS or the hand-held terminal. The files are deleted from the hand-held terminal if the STG files are being shown in the directory view.

5.5.3 Format MDS (Tag Format)

Before it can be used with the filehandler, the MDS must be formatted. Before formatting, it is important to set the memory size of the MDS correctly. Use the Extras/Parameter function for this. Formatting deletes all data from the MDS, and a new file structure is set up.

The “FILEHANDLER” Program

Page 52

R 01.04

E-46

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.5.4 Attribute File (File Attribute)

This command can be used to assign access rights to the individual files. This protects the files from unauthorized and unintentional overwriting. The directory view shows the file attribute in the right-hand column (see chap. 5.3.2). The following file attributes are available.

Attribute Description

– No attribute or an existing attribute is deleted. R Read only. The file can only be read. It cannot be written, overwritten

or deleted.

W Write once. The file can be written once. The file cannot be written

again. It also cannot be deleted.

F Fixed length. The file can be read as often as desired. It can only be

written when this does not change the length of the file. Data cannot be appended, and the file cannot be deleted.

F/R “Fixed length” and “read only” are set. This attribute has the same

effect as the “R” attribute.

File attributes can only be assigned to MDS files. Files on the RAM of the hand-held terminal always have the type “–” (i.e., they can always be changed or deleted).

The “FILEHANDLER” Program

Page 53

R 01.04

E-47

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.5.5 MDS Status (Tag Status)

This command shows the status of the MDS in several consecutive screens.

MDS type (Tag type) This value is identical to the specification of the MDS type with the Format command on a SIMATIC.

Gross MDS size (Tag whole size) The size of the MDS which was set with the Format command is indicated.

ECC Indicates whether the MDS is used with or without ECC

MDS (Tag) Indicates the name of the MDS which was written to the MDS with the Format command

MDS size (Tag size) Indicates the maximum memory area which can be used by the user

Bytes free Indicates the number of data bytes on the MDS which the user can still use for his/her data

Directory free (Dir free) Indicates the number of files which can still be set up on the MDS

Battery 1 (Bat1) Status of the RAM battery. This value does not apply to the EEPROM MDS.

Battery 2 (Bat2) Status of the dialog battery with MDS 507

Amount of processing (Work Counter) Number of processing procedures which were performed with the MDS since it was initially formatted. This value is particularly important for the EEPROM MDS since the number of write-accesses is limited for these types of memory.

ECC Correct Counter for the number of ECC offsets performed. If this counter has a value other than zero, the MDS must be replaced in the near future. An EEPROM memor

was write-accessed too often.

The “FILEHANDLER” Program

Page 54

R 01.04

E-48

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.5.6 MDS Cover

The Cover command protects the entire file structure on the MDS. If an MDS is “covered”:

S Every file can be read. S Every file can be written as long as the file length is not changed. S No files can be deleted. S No new files can be created. S The format of the MDS can be initialized again. This “uncovers” the MDS. S The “covered” state can be canceled with a Cover command and the setting

“not covered.”

5.6 The Editor Functions

5.6.1 Display Directory

This function switches the display to the directory view (see chap. 5.3.2). The directory which was read last is displayed. The directory can be from the MDS or the hand-held terminal.

5.6.2 Display Editor

This function switches the display to the editor view (see chap. 5.3.1). The display shows the file which was read last. This file can be from the MDS or the hand-held terminal.

The “FILEHANDLER” Program

Page 55

R 01.04

E-49

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.6.3 Change File Size (File Size)

The editor shows the current size of a file in the second line. This length can be modified with the “File Size” command. When the file is made longer, an appropriate number of zeros (00 Hex) is appended to the end of the file. The editor shows the appended portion with inverted digits.

5.6.4 Delete Display (Clear Display)

This function clears the memory of the editor display. The hexadecimal value of the filler character can be specified. The standard filler character is 00hex. After deletion, all data in the display are shown inverted to indicate that no data have been entered yet by the user.

5.6.5 Jump to Address

Normally the cursor is positioned within a file with the four arrow keys (, , , ). With large files, it is much quicker to use the “jump to address” function to

position the cursor anywhere within the file. You can also call the “jump to address” function very easily with the Tab key.

5.6.6 Display Setup

The display is set here. You can choose either hexadecimal or ASCII format. In ASCII format, the characters which cannot be shown appear as white fields. For more information, see the ASCII table in appendix A.3.

The “FILEHANDLER” Program

Page 56

R 01.04

E-50

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

5.7 The Extras Functions

5.7.1 Parameter

The “parameter” function is used to make the basic settings for the filehandler.

Parameter Description

MDS size The gross memory size of the MDS is set here.

This memory size is shown in the first line of the display. The Format command uses the memory size to specify the file system. If the “MDS size” parameter does not correspond to the MDS being used, the MDS can still be used. Only the Format command would produce the wrong result.

MDS type Here you can switch between RAM, EEPROM and MDS 507. FRAM

memory is treated as RAM memory. If EEPROM is selected, the battery error message is suppressed on the display since these MDSs do not have batteries. If MDS 507 is selected, the dialog battery is also evaluated. When empty, this is shown on the display.

ECC SLG no.

(hex)

Activate/deactivate ECC driver When an MDS is processed, the SLG no. selected here is written to

the system area of the MDS. It has no effect on the function of the Filehandler program on the STG.

EAKO The entry/exit check cannot be set on the STG with the filehandler.

The STG does not use entry/exit control (AEKO = 4).

The “FILEHANDLER” Program

Page 57

R 01.04

E-51

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

5.7.2 Password for Filehandler (Password for FH)

The filehandler password protects the STG data on the MDS from being manipulated by unauthorized parties. The passwords for the “Filehandler” and “MOBY D/E/F/I/U” programs are identical. See chapter 4.5.2 for a description of how to handle the password.

5.7.3 Communication

In principle, communication of the filehandler is always set to “read head.” However, the filehandler can be changed to “ASM on RS 232” as an option. A type “ASM420-RS232” module can then be connected to the hand-held terminal. For more information, see chapter 6.6.

Remember that a type “ASM 421” module cannot be used with the STG.

5.8 The “?” Functions

These functions are the same as those of the “MOBY D/E/F/I/U” programs. See chapter 4.6.

The “FILEHANDLER” Program

Page 58

R 01.04

E-52

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

6 Expanded Functions

6.1 Storing the MDS Data on the Hand-Held Terminal

The data read from the MDS are automatically stored on the hand-held terminal in a file named “READ_D.HEX,” “READ_E.HEX,” “READ_F.HEX,” “READ_I.HEX” or “READ_U.HEX” on the “RAMDRIVE” drive of the PSION. Every additional read command overwrites this file.

When the MDS is write-accessed, the write data are written from the editor to the MDS and also to the “RAMDRIVE (M:)” drive of the PSION under the name “WRITE_D.HEX,” “WRITE_E.HEX,” “WRITE_F.HEX,” “WRITE_I.HEX” or “WRITE_U.HEX.” Every additional write command overwrites this file.

The “file/load file” function shows all files with the file extension “.HEX.” You can select one of them with the cursor keys. This file is then loaded to the editor. There is no storage under the name READ_x.HEX or WRITE_x.HEX.

The “file/save” function stores the data of the editor in a file with the file extension “.HEX” and at the same time the ID number in a file with the file suffix “.HX1” on the RAMDRIVE drive of the PSION (i.e., drive M:). You can specify any name of 1 to 8 alphanumeric characters.

Note

When you read data from the MDS, modify data in the editor and then save the data, the modified data will be stored in the .HEX file.

Expanded Functions

Page 59

R 01.04

E-53

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

6.2 Copying MOBY Data from and to the HandHeld Terminal

6.2.1 What Is Needed in Addition?

S The PsiWin program. This is a file manager available from PSION for the

PSION Workabout hand-held terminal.

S A 3link interface with the applicable cable for connecting the PC to the

PSION Workabout

These components can be ordered directly from PSION. See appendix A.1.

6.2.2 Using the PSION File Manager

The PSION file manager is installed in the Windows Explorer of your PC. This provides your Explorer with additional drives. The following figure shows a sample configuration. You will find it very easy to copy data and programs the way you always have with Explorer.

The PSION desktop is set up in Explorer when PsiWin is installed.

You will not be able to open the PSION desktop in Explorer until you connect the PSION with the 3link cable and the wall holder, and enable the interface for communication (i.e., port C).

Expanded Functions

Page 60

R 01.04

E-54

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

How to enable port C:

S Exit the STG program with EXIT. The basic

PSION menu appears.

S Menu key: Position the cursor on “System

screen,” and acknowledge with “Enter.” A user interface similar to Windows appears.

S Make the following settings in this window.

Remote link = ON, baud rate = 19200, port = C, parameters = (don’t specify anything).

S Before you acknowledge with “Enter,” establish

a connection to the PC with the 3link cable described in chapter 6.2.1. Otherwise you will receive the message “Device does not exist.”

S Menu key: Call SPEC/REMOTE LINK. The

“Remote link” window appears.

If you made wrong entries during this procedure and are unable to continue, perform a system RESET as described in chapter 6.7.

If the message “keine Verbindung” (i.e., no connection) continues to appear in the PSION desktop directory of Explorer, check the 3link cable between the hand-held terminal and the PC, and the REMOTE setting on the hand-held terminal.

Open the file tree of the hand-held terminal by double-clicking the “RAMDRIVE” drive. There you will find, among others, the “READ_D/E/F/I/U.HEX” file and the files which you stored with the extension “.HEX.” Now drag and drop or copy these files from the PSION drive to the PC drive.

Expanded Functions

Page 61

R 01.04

E-55

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

The length of the READ or WRITE file is the same as that of the MDS which was read.

READ_D.HEX: 44 bytes for I-Code1

112 bytes for I-Code SLI 256 bytes for Tag-it HF-I

1000 bytes for my-d

READ_E.HEX: 768 bytes for MOBY E (in normal mode)

1024 bytes for MOBY E (after reading the raw data) 1024 bytes for MOBY E (in SIM mode)

READ_F.HEX: 5 bytes for MOBY F (after reading an F1xx MDS)

192 bytes for MOBY F (after reading an F4xx MDS) 256 bytes for MOBY F (after reading the raw data of an

F4xx MDS)

READ_I.HEX:

Setup Setting No ECC With ECC

62 bytes

128 bytes

2 KB 8 KB

32 KB

128 2045 8189

32765

112 1778 7154

28658

READ_U.HEX:

Setup Setting

2 KB

32 KB

2048

32768

The contents of the file can now be indicated and changed with an appropriate editor on your PC.

When ASCII data were read from the MDS:

Any editor can be used (e.g., NOTEPAD, WRITE, WORD and so on).

When binary data were exchanged with the MDS:

Use a HEX editor. HEX editors are available on the shareware market (e.g., Hedit and so on) or on the professional market (e.g., Codewright).

After concluding your session with PsiWin, the remote-link connection should be disconnected again. To restart the STG application, see chapter 6.7. Before starting a new session with PsiWin, the STG application should be exited.

Expanded Functions

Page 62

R 01.04

E-56

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

6.2.3 Organization of the READ.HEX File

The READ_x.HEX file only contains the pure data which also exist on the MDS. The length of the file is the same as that of the MDS, specified in bytes.

6.2.4 Organization of the READ.HX1 File

The READ_x.HX1 file contains the ID number. The READ_x.HX1 file is only created for MOBY D/E/F/U.

6.3 Functions with the PSION Operating System

You can use the FILE/EXIT menu command to access the operating system level of the hard-held terminal. We will now describe some of the functions which are available with the PSION operating system.

S Simple writing of a batch file to copy MDS data to a memory card (e.g., on

drive B:).

S Generation and modification of an AUTOEXEC file to change the time for au-

tomatic switch-off or the time for the backlight to save battery power and thus increase operating time for one battery charge. The AUTOEXEC file is located in directory A:\BTF\Autoexec.btf.

S Edit the read MOBY data with the PSION editor. Remember that this editor

can only be used when the MDS data are in ASCII format.

S Spread sheet function S Calculator S Execution of DOS commands

See the manual entitled “PSION Workabout USER GUIDE” for a detailed description of operating system functions and standard programs. This manual can be ordered from PSION. See appendix A.1.

Expanded Functions

Page 63

R 01.04

E-57

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

6.4 Parallel Execution of Several Applications

Several applications can be processed at the same time on the Windows level of the PSION hand-held terminal.

Proceed as shown below.

S Exit the MOBY service and test program. The following basic PSION screen

appears.

S Menu → System screen

You are in the Windows level of the PSION. Several icons appear on the display.

S Move the cursor to the right until the IMG application appears on the display. S The applications which you can start are shown under the IMG icon.

– MOBY D/E/F/I/U = MOBY service and test program for the particular

MOBY family – FILEHAND = MOBY filehandler programm – MENU = MOBY program selection menu – Other customer applications. These must be stored in the IMG directory.

On delivery, no other application is indicated here.

S Select the MOBY D/E/F/I/U application with the cursor keys, and press Enter.

The familiar MOBY STG application is started.

S Press the key combination “ + TAB.” The basic PSION screen reappears

on the display.

S Select the next program to be started on the IMG icon or on the total Win-

dows screen (e.g., the CALC pocket calculator), and start it by pressing Enter. This program now appears on the monitor screen.

Expanded Functions

Page 64

R 01.04

E-58

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

This procedure can be used to start applications and PSION operating programs in addition to the normal MOBY application. All programs run simultaneously on the hand-held terminal.

6.5 Automatic Power Saver Function

The PSION hand-held terminal has an automatic power saver function. This is activated after no keys have been pressed on the PSION for approximately 5 minutes.

In addition, the “MOBY D/E/F/I/U” programs have another power saver function. The MDS command being executed is interrupted if no MDS is detected 30 seconds after the start of an MDS command or the MDS being processed is moved out of the field for more than 30 seconds. The following message appears.

You can now completely terminate the command with ESC or continue with ENTER. If you decide to continue, the interrupted command is continued at the point at which it was interrupted.

6.6 Connecting SIM Devices (MOBY E/I/V)

A MOBY E SIM can be connected to the RS 232 interface of the PSION. The following figure shows the connection diagram. Before commissioning, a switch must be made to MOBY E/SIM or ASM 420/I/V with the “EXTRAS/COMMUNICATION/PROTOCOL” function. With this configuration, SIM can be used to work with the “MOBY” program and user applications with the MOBY library. Cf. appendix A.2.

MOBY E/SIM:

220 V AC

24 V DC

Cable (6GT2 391-1DH50)

and

Power pack (6GT2 090-0HB00)

Expanded Functions

Page 65

R 01.04

E-59

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Note

Since the standard SIM uses cyclic operation, it takes much, much longer to process a read/write command than with the STG read head. The EXTRAS/MOBY E Setup/MODE command can be used to switch the SIM to the faster read mode. This command must be repeated each time SIM is turned on.

ASM 420/I/V: This settings permits an ASM 420/RS 232 to be connected to the hand-held

terminal. The connection cable must comply with the specifications in the ASM 420 documentation. In ASM 420 mode, the MOBY V driver is always enabled during the “MOBY I” program. SLG 65 can be used on the ASM 420 with this. Use of MOBY I SLGs is limited.

Assignment of the RS 232 interface on the hand-held terminal:

Pin Designation

2 TxD 3 RxD 5 Gnd

6.7 System RESET

The hand-held terminal executes a system RESET when the device is turned on for the first time after the batteries have been installed. This RESET is the same as a hardware RESET.

A system RESET can also be triggered by hand. To do this, press the key + Ctrl + Del (Shift + Esc + Del on the PSION with the numerical keyboard) simultaneously.

During the system RESET:

S The MOBY STG application is started again. S Data stored in flash memory are always retained (drive A: or B:). S The data in RAM memory (drive “RAMDRIVE:”) are retained. However,

these data will be lost if all batteries (including lithium cell) of the PSION are removed.

Expanded Functions

Page 66

R 01.04

E-60

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

7 The “MOBY D/E/F/I/U” Programs with the

PSION Numeric Model

The MOBY service and test program also functions without restrictions on the PSION Workabout with numeric keyboard. This PSION model is useful for applications in which only simple and identical applications are performed by untrained personnel. This model of the hand-held terminal can be ordered directly from PSION. See appendix A.1.

The functionality of the 4 function keys can also be put to good use. The following STG functions can be called directly via function key.

F1 = Read MDS F2 = Write MDS F3 = Load data from file F4 = Save data in file

Data can only be entered with the numeric keys.

The “MOBY D/E/F/I/U” Programs with the PSION Numeric Model

Page 67

R 01.04

E-61

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

8 Error Messages

What to do when ...

... The PSION display goes blank during MOBY read/write.

S The batteries of the PSION are empty. Insert device in the charging shell,

or install new batteries.

S The battery pack was installed incorrectly on the basic device. The catch

of the battery pack must be on the left side.

... The display remains blank after the device is turned on.

S The batteries are empty. S The contrast of the display is not adjusted correctly. To adjust, use the

key in the top row.

... Error messages appear but they are not defined anywhere.

S Remove both batteries from the basic device. Wait 60 seconds, and re-

place them again. The device is now in its status on delivery. If the error continues to occur, the device may be defective.

... LED for communication is red on the STG U hand-held terminal.

S The battery of the MOBY U antenna is empty. → Charge battery (see

chap. 3.4).

... No communication between the basic device and the antenna (handshake

timeout) with the STG U hand-held terminal.

S The battery of the MOBY U antenna is empty. → Charge battery (see

chap. 3.4).

S Check the RS 232 interface on the basic device for secure plug connec-

tion.

... Operation time of the MOBY U antenna gets shorter and shorter.

S Install a new battery in the MOBY U antenna.

Error Messages

Page 68

R 01.04

E-62

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

8.1 Error Messages with the “MOBY D/E/F/I/U” Programs

The messages in the following tables can occur during operation. The messages are indicated in a separate window. A message can have the following format.

The message is coded in several digits, has the format is xx/yy/zz, and is used for precise error analysis. The following tables list the types of errors and the error designations in detail. The information in /zz is included in some messages. “zz” contains additional error information (e.g., the block in which the error occurred).

Type of error

Exact error designation

Type of Error Description

1 to 2 General errors 3 to 9 MOBY E errors 10 to 15 MOBY F errors 20 Timer errors 30 to 37 MOBY I errors 42 to 45

52 to 57

MOBY D errors MOBY D ISO errors

60 to 72 MOBY U errors

Error Designation Possible Causes and Their Correction

1, 2, 3, 4, 5, 6 S Reader device fails to send start protocol.

S Is read head screwed on? S Does the read head match the protocol setting? (See

menu: Extras/COMMUNICATION.)

S Batteries in the reader device are dead. (The batteries may

be defective.)

S Internal program error S The date is not permitted for the “read MDS status” function.

(MOBY U: Error designation = 3 for error type = 64) ⇒ Set date (see chap. 4.2.5).

7 Interface defective 10, 11, 12 Reader device doesn’t answer at all or sends an incorrect an-

swer (MDS D1xx/MDS F4xx).

Error Messages

Page 69

R 01.04

E-63

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Error Designation Possible Causes and Their Correction

20 S Reader device doesn’t answer.

S Check parameters in the Extras/COMMUNICATION menu.

With SIM mode, “Interface” and

“Protocol” must both be set

to SIM.

S Batteries in the reader device are empty. (The batteries

may be defective.)

21 Reader device doesn’t answer at all or sends an incorrect

answer. S Internal program error (MDS D1xx)

22 to 27 S Reader device sends the wrong answer.

S MDS is not personalized with the MOBY key. S Internal program error (MDS D1xx/MDS F4xx)

32 Illegal request, internal program error

S Check contact to read head. S Read device doesn’t answer (MDS E6xx)

33, 34, 35, 36 Internal program error

S Exit STG program, and start again. S Read/write error (MDS F4xx)

37 S Read head gives you an error message.

S Read head is faulty. S CRC error of MDS. Communication error to MDS. MDS is

located on the boundary.

S MDS has a defect. S Internal program error

38 Specified block is write-protected. 39 Several MDSs are in the field.

S Internal program error (MDS D1xx)

40, 41, 42 Reader device doesn’t answer at all or sends an incorrect an-

swer (MDS D1xx/MDS F1xx/MDS Uxxx).

S Internal program error (MDS D1xx) S Check interface to MOBY U antenna (MDS Uxxx).

43 User termination with ESC 45 Wrong answer from read device 50 Error while reading or writing the MDS data

52, 53, 54, 55, 56, 57

Internal program error on MOBY read head

63 Authentication error. The MDS doesn’t have the MOBY key.

S Try setting the “B” key under “Extras/MOBY E Setup.”

Error Messages

Page 70

R 01.04

E-64

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Error Designation Possible Causes and Their Correction

65 Interface error. Appears when a SIM is connected.

S Check parameters in the “Extras/COMMUNICATION”

menu.

S Check plug and cable to SIM.

66 General read/write error on MOBY read head 67 Internal program error on MOBY read head

70 S Write not successful

S Several tags in the field 80 MDS type on reader device is not supported. 81, 82 S Read device sends wrong answer.

S MDS not personalized with MOBY key

S Internal program error (MDS Fxxx)

101 to 132 Read device sent error (MOBY I/U). Specification of certain errors: 101 Presence error

S No MDS in the field which has the MDS ID number con-

tained in the command.

103 Error in the connection to the SLG

S Read head hardware has a defect. 104 Error in MDS memory

S Execute INIT command. Before executing this command,

make sure that the memory size of the MDS is set correctly under “Extras/MOBY I Setup.”

S The MDS is defective. 105 MOBY command cannot be interpreted by the read head/

MOBY U antenna.

S Check the memory size under “Extras/MOBY I Setup” or

“Extras/MOBY U Setup.”

106 S Field interference on read head. External interference.

S The MDS left the field during communication.

S Field interference during communication

107 Too many sending errors. The MDS wasn’t able to correctly

receive the data from the read head.

S The MDS is located in the boundary area of the read head. 109 CRC error due to field interference while initializing the MDS 110 MDS cannot be initialized and is defective.

Error Messages

Page 71

R 01.04

E-65

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Error Designation Possible Causes and Their Correction

111 Timeout during initialization (MOBY I)

S The MDS is located in the boundary area of the read head.

S An MDS 507 is initialized but MDS 507 mode has not been

enabled under “Extras/MOBY I Setup.”

The MDS memory cannot be read correctly (MOBY U). 112 S The MDS memory cannot be written and is defective.

S The OTP memory cannot be written again. 113 The address area of the MDS was exceeded.

S Check the memory size under “Extras/MOBY I Setup” or

“Extras/MOBY U Setup.”

114 ECC error or MDS not initialized in ECC mode

S Enable ECC mode under “Extras/MOBY I Setup,” and then

execute the INIT command.

115 Reset message after return of power

S The hand-held terminal has a defect in the power supply to

the read head. (Try charging/replacing the batteries.)

S The hardware of the read head has a defect. 125 Internal program error. Previous command is active. 129 The number of MDSs in the field is not permitted. Number of

MDS > multitag in the “SLG Status” function under “Extras.” 130 Internal program error. The telegram layout of the command to

the read head is wrong. 180 to 243 Internal program error (MDS D1xx)

Turn the device off and on again. If error continues to occur,

contact Customer Support and specify the error number. 251 Read/write comparison not successful 255 No card/no MDS in the field

Error Messages

Page 72

R 01.04

E-66

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

8.2 Error Messages with the “FILEHANDLER” Program

The following table lists the messages which can occur with the filehandler. A filehandler error message looks like this.

The filehandler error is shown in the same way as the filehandler on the SIMATIC. The error message has one alpha character followed by a 3-position number. Most of the error codes are identical with the error numbers of all MOBY filehandler interfaces.

Type of error (see chap. 8.1)

Exact filehandler error

Filehandler

Error

Description of Error, Its Cause and Correction Type of

Error

A006 Unknown command. Command identifier KK is illegal. A011 With 1st command block: DBN not 1

With next block: KK or DBN incorrect

A015 Checkbyte error while receiving from S5

Protocol

errors

A016 Command from other sender is being processed. A020 Wrong number of characters in the telegram B001 Error in the connection to the SLG

Read head defective

SLG errors

C002 Error on RAM of the MDS. Replace MDS and perform

FORMAT. C006 Presence error. MDS in boundary area. C007 Parameterization error during FORMAT. Command

cannot be interpreted. C008 Too many sync attempts. Field interference on read

head. C009 Too many sending errors C010 CRC sending error

MDS errors C011 FORMAT. CRC error while receiving. C012 FORMAT. MDS cannot be initialized. C013 FORMAT, timeout. MDS in boundary area. C014 FORMAT, not initialized. Check Extras/Parameter. C015 CMD address error. Check Extras/Parameter. C016 ECC error. Format MDS again. Disable ECC mode. C017 General driver error

Error Messages

Page 73

R 01.04

E-67

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Filehandler

Error

Type of

Error

Description of Error, Its Cause and Correction

D001 Only RESET command permitted D005 Illegal parameters for FORMAT, CREATE, WRITE,

UPDATE or ATTRIB D009 RESET command parameter wrong D014 CREATE and WRITE: The user data area of the MDS

is completely full.

Job-related

D015 Only FORMAT command possible. MDS not identified.

Job related

errors

D018 Start address in the command is outside the data area

(i.e., start address > file length). D022 Directory and/or FAT. Modifying an MDS protected with

COVER is illegal. D023 COVER: MDS name wrong E001 MDS type is wrong or doesn’t match the set mode

(ECC). E002 CREATE command: No more directory entries free

Directory-

E003 CREATE command: File already exists in the directory.

relate

errors

E005 READ or WRITE: A FAT block sequence error was de-

termined. The FAT is defective.

errors

F001 The addressed file does not exist. F005 WRITE/UPDATE/DELETE command for a file which is

protected with the appropriate attribute

File-related errors

H140 Serial interface error H141 Wrong interface H142 Faulty timer H143 Interface error H144 Start-protocol error H145 Reset error, WRITE

Error

H146 Reset error, READ, no STX

Error

messages

H147 Reset error, READ, timeout

of the filehandler

H148 Reset error, READ, wrong response

filehandler

application

H149 Start error, WRITE

H150 Start error, READ, no STX H151 Start error, READ, timeout H152 Start error, READ, wrong response H153 Start error, WRITE, length too long

Error Messages

Page 74

R 01.04

E-68

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

9 Technical Data

Hardware

Processor NEC V30mx, 27.68 MHz, 80C86-compatible RAM memory 2 Mbytes of which approx. 1.8 Mbytes can be used as desired ROM memory 2 Mbytes for operating system User program 1 MB (with MOBY service and test program) Monitor screen Graphic LCD monitor screen with 240 x 100 pixels, gray-stage

scale, backlighting can be turned on Keyboard Alphanumeric with 57 keys Sound Piezo signal encoder Power supply NiCd battery pack with 2 type-AA cells (1 Ah)

High-speed chargeable, automatic switch-off

Operation time: 20 hours

(Read head inactive, display not lighted)

4.5 hours

(Read head active, display not lighted) 10 hours (Read head inactive, display lighted)

Backup battery: 3 V lithium cell (CR 1620) Interfaces LIF interface (LIF = Low Insertion Force) for battery charging

and communication with PC and printer (3link cable not in-

cluded)

RS 232 and TTL interface for connection of a MOBY read

head

RS 232 interface for connection of a MOBY U antenna Security Locking mechanism for battery and program memory

Software

Operating system EPOC/16 multitasking, graphics support, GUI interface, Inter-

preter similar to MS-DOS File management MS-DOS-compatible Integrated

software

MOBY service and test program, spread sheet calculation,

data base, pocket calculator, communication

1 Does not apply to MOBY U since the antenna has its own battery. For operation time (antenna

active), see technical data of MOBY U antenna.

Technical Data

Page 75

R 01.04

E-69

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

Technical Data Complete Device

(incl. Batteries)

Read Head

Dimensions 90 x 260 x 35 [mm]

(MOBY D/E/F/I)

90 x 64 x 35 [mm] (MOBY D/E/F/I)

282 x 235 x 93 [mm] (MOBY U) Weight Approx. 480 g

(MOBY D/E/F/I)

Approx. 100 g (MOBY D/E/F/I)

Approx. 1450 g (MOBY U) Approx. 1100 g (MOBY U) Temperature Operation: –20 °C to +60 °C

Storage: –25 °C to +70 °C (without batteries) Relative humidity 0% to 90%, no condensation Protection rating IP54 (protected against splashed water)

Shock resistance Max. falling height on concrete: 1 m (MOBY D/E/F/I)

0.5 m (MOBY U) EMC EN 55022 Electrostatic, RF,

EFT

IEC 801-2; IEC 801-3; IEC 801-4

2 With STG U hand-held terminal, only for complete device with PSION Workabout

Technical Data

Page 76

R 01.04

E-70

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

RF read/write head

MOBY D 13.56 MHz (I-Code; Tag-it)

Max. read distance: 60mm with MDS D139

25mm with MDS D160

Labels based on I-Code in standard size (approx. 85 x 55 mm): Max. read distance: 75mm with I-Code1

100mm with I-Code SLI 100mm with Tag-it HF-I 100mm with my-d

Certifications: ETS 300 330

MOBY E 13.56 MHz (MIFARE)

Max. read distance: 30 mm with MDS E611

18mm with MDS E600

8mm with MDS E624 4mm with MDS E623 3mm with MDS E623,

mounted in metal

Certifications: ETS 300 330 reg. no. G100213L

FCC ID: KR5MIS

MOBY F 125 kHz (HITAG)

Max. read distance: 80 mm with MDS F125

50mm with MDS F415 60mm with MDS F124

Certifications: ETS 300 330 reg. no. G100294L IF

MOBY I 1.81 MHz (data); 134 kHz (power)

MDS Type Max. Read Distance

(in mm)

401/402

404/514/413E

403 506

439E

507 with battery

507 without battery

8 12 12 35

Certifications: ETS 300 330 reg. no. TTI-P-G 128/96

FCC ID: KR5MIS-I

Technical Data

Page 77

R 01.04

E-71

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

MOBY U antenna

Transmission frequency 2.4 to 2.4835 GHz Band width 2 x 1 MHz within 83 MHz Gross bit rate of radio channel 384 kbit/sec Data rate (read/write), net Approx. 8/4.8 Kbyte/sec without bunch Antenna

S Emission direction S Angle of opening S Polarization S Emission capacity S Emission density

Vertical to back of MOBY U antenna Approx. 90° (cone-shaped antenna field) Circular < 50 mV/m at 3-m distance < 0.5 µW/cm

at distance of 1 m Range (read/write) S Limit distance (S

)

S Max./min./standard S Site resolution

0.15 m to 3 m Corresponds to set range limitation 3 m / 0.5 m / 1 m Can be set over range limitation in increments

of 0.5 m

MDS acquisition time Approx. 3 sec with 1 MDS

(after communication button is pressed)

Power supply Lithium ion battery pack 2SIP CGR18650 HG

7.2 V 1.8 Ah Rapid-charge capability, automatic switchoff,

lifespan: approx. 500 charging cycles Current consumption (antenna on) < 800 mA Operation duration

> 2 months (antenna not active)

2 hours (antenna active)

The antenna is turned on via the communica-

tion button only for communication and then

automatically switched off again after the func-

tion is executed. The shortest switchon time for

communication is approx. 3 sec (depending on

the data volume) when an MDS is located in

the field. Operating modes

S Off S Search

S Communication

Antenna off

Ready to receive and evaluate search informa-

tion sent by the MDS

Communication with the MDS: read, write or

initialize Minimum distance to an SLG U92

or another STG U

≥ (set range + 0.5 m)

Technical Data

Page 78

R 01.04

E-72

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

Serial interface to PSION

S Transmission speed S Transmission protocol

RS 232

115.2 kBaud

3964R Interface for battery charging

S Voltage/current S Charge duration

4-pin socket for connection of the STG U

power pack

12 V DC/1.225 A

> 1.5 h

(lithium ion battery pack 2SIP CGR18650 HG) Operator control elements Communication button

(for triggering communication) Indication elements S LED for charging the batteries

–On

– Not on

2 LEDs

Power pack connected

Red: Device is defective. Yellow: Batteries are being charged. Green: Batteries are charged.

Power pack not connected. S LED for communication

– On

– Not on

Communication button pressed and communi-

cation not concluded

Red: Battery capacity is not sufficient for

communication.

Yellow: Antenna is activated. Ready to

identify an MDS or identify an MDS and communicate with it

Communication concluded or not started Housing S Color/material

Black/polyamide 6 GF 30 Certifications RF: I-ETS 330440+C1:1997

SAR: 99/519/EG

Safety: EN 60950:2000

EMC: EN 301489-01:2000

EN 301489-03:2000 ENV 50204:1995

FCC ID: NXWMOBYU-STGU

Safe for pacemakers

3 The operation time corresponds to the amount of time the antenna is on. For each MDS

function, this means the time from activation of the communication button to conclusion or termination of the selected MDS function. If you do not point the hand-held terminal towards an MDS after you press the communication button, the function is terminated after 30 seconds. The antenna is on during this time.

Technical Data

Page 79

R 01.04

E-73

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

STG U power pack With cable switch (on charging cable) and

charging adapter for PSION Workabout Input voltage range 90 V to 264 V AC

Frequency range of the input voltage

47 Hz to 63 Hz

Nominal input current 400 mA Nominal output voltage 12 V DC Nominal output current 1.25 A Basic load None Short-circuit proof Yes Potential isolation, primary/secon-

dary

3 kV AC

Dimensions, power pack (L x W x H in mm) 87.5 x 51.5 x 34 (without connection plug)

Color/material Black/plastic (PPE-V1) Ambient temperature

S Operation S Transportation and storage

0 °C to +40 °C

–40 °C to +70 °C Relative humidity 0% to 90%, no condensation Protection rating in acc. w.

DIN EN 60529 IP40 Weight, approx. 250 g Charging cable 2 x 0.5 mm2 / 2 m long Primary plug connector Can be changed

EU, UK, USA and ROW plug connector

(EU plug connector included) Certifications 220 V to 240 V (Europe): CE

120 V (Canada and USA): cULus

Safety: EN 60950

EMC: EN 55011,

EN 55014 and EN 55022 Class B

Technical Data

Page 80

R 01.04

E-74

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

A Appendix

A.1 Ordering Components for Expanded

Functions

The expanded functions of the MOBY STG hand-held terminal require components which are not available from Siemens A&D SE.

If you need these components for your MOBY application, please contact PSION directly or its representative in your country. You will find addresses and order lists from PSION on the Internet under www.psionteklogix.com. The PSION representative in your country is also located under this Internet address.

The following components are required for the STG application as options.

Ordering Designation Remarks

3link interface for wall and vehicle holder Dual AT/XT connection cable for the PC PsiWin software

(for Win95/Win98/NT/2000)

Also available free of charge under the PSION Internet address

User’s guide for PSION Workabout Ask your PSION representative.

Additional Components required for writing your own applications

C development package for Workabout (SIBO C SDK)

Standard or professional available, incl. Top Speed C compiler

Manual for C development package

Ask PSION or its representative directly for information on the following PSION components.

S OVAL programming environment S Memory expansion S High-speed charging devices S PSION Workabout with numeric keyboard

These components are not required for the STG application. They are only of importance if you want to program your own identification application on the hand-held terminal.

ppendix

Page 81

R 01.04

E-75

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

A.2 Developing User Applications

What Do I Need?

The C development package from PSION (SIBO C SDK incl. Top Speed Compiler) is required for user applications.

For the communication connection, you will also need a 3link interface and the PC cable with a 9-pin sub D and mini DIN plug connector.

Although, in principle, applications can also be developed with the Basic programming language OVAL, the MOBY library cannot be used.

The MOBY Library

A library for MOBY D, MOBY E, MOBY F, MOBY I and MOBY U is available. The library (MOBY D/E/F/I/U) must be ordered under order number 6GT2 381-1AB00. The C library also includes a description of the interface commands.

The following table summarizes the implemented commands.

The MOBY D Library

Function Call Short Description

RF_ReadBlock Reads a block from the MDS RF_WriteBlock Writes a block RF_ReadTagId Selects the tag. Reads the TagId RF_Status Determines the tag type RF_Init Writes all user blocks nMobyDOpen Opens an interface vMobyDClose Closes the opened interface

ppendix

Page 82

R 01.04

E-76

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

The tables below provide a summary of implemented commands.

The MOBY E Library

Function Call Short Description Type of Command

CCT_READ_N_BLOCK Read card data (1 to n data

blocks, max. of 96 bytes)

Standard

CCT_WRITE_N_BLOCK Write card data (1 to n data

blocks, max. of 96 bytes)

Standard

CCT_WRITE_SIGNAL Address digital output, re-

served for switching the antenna

Standard

CCT_OFF Turn off antenna field Standard CCT_MODE Set field mode of the

antenna field

Standard

CCT_OPEN Open logical device Only for

SIM operation via RS 232

CCT_CLOSE Close logical device Only for

SIM operation via RS 232

CCT_SETKEY Parameterize read-card/

write-card interface

Optional

CCT_SET_KEY_TEMP Change temporary key Optional CCT_GET_FIELD_STATE Scan current card indices Optional CCT_RESET Reset read head Optional -

general command

Although the commands of the MOBY E library are the same as those of the standard MOBY E library “CCTWAPI,” not all commands of “CCTWAPI” are available on the hand-held terminal.

ppendix

Page 83

R 01.04

E-77

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

The MOBY F Library

Function Call Short Description

proloc_ReadBlock Reads a block from the MDS (16 bytes) proloc_ReadPage Reads a page from the MDS (4 bytes) proloc_WriteBlock Writes a block to the MDS (16 bytes) proloc_WritePage Writes a page to the MDS (4 bytes) proloc_GetSnr Reads the TagId from the MDS nGetTagType Determines the type of MDS in the antenna field nMobyFOpen Opens a serial interface in PSION vMobyFClose Closes the opened interface

The MOBY I Library (normal addressing of MDS)

Function Call Short Description

moby_init Initializes an MDS with a filler character from ad-

dress 0 to the end address moby_read Reads a data block from the MDS moby_write Writes a data block to the MDS moby_reset Sends a reset command with parameterization

to the read head moby_status Sends a status command to the read head nMobyIOpen Opens the interface and turns on the read head vMobyIClose Closes the opened interface. The read head is

turned off. nMobyIReadStartProtocol Reads the startup telegram from the read head

ppendix

Page 84

R 01.04

E-78

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

The MOBY I Library (filehandler addressing)

Function Call Short Description

wFhRead Reads a complete file from the MDS wFhWrite Writes a file or appends data to a file wFhMdsStatus Sends a status command to the MDS wFhAttrib Sets a file attribute wFhDelete Deletes a file from the MDS wFhCreate Sets up a new file on the MDS wFhFormat Formats an MDS wFhDir Reads a directory from the MDS wFhCover Protects the MDS file structure wFhDirInfo Writes information from the “DIR” structure to the

“DirInfo” structure nTagTypeFromTable Returns the MDS type from a table lTagLenFromTable Returns the MDS size from a table Fhreset Resets the filehandler nFhOpenCom Opens the interface and turns on the read head vFhCloseCom Closes the opened interface. The read head is

turned off.

ppendix

Page 85

R 01.04

E-79

STG Hand-Held Terminal (5)J31069-D0126-U001-A5.1-7418

The MOBY U Library (normal addressing of MDS)

Function Call Short Description

moby_u_init Initializes an MDS with a filler from address 0 to

the end address moby_u_read Reads one data block from the MDS moby_u_write Writes one data block to the MDS moby_u_reset Transfers reset command with parameterization

to the antenna moby_u_mds_status Reads the status data from the MDS (e.g., the

battery lifespan) moby_u_slg_status Sends status command to the antenna nMobyUOpen Opens interface. Turns on antenna. vMobyUClose Closes the opened interface. The antenna is tur-

ned off. nMobyUReadStartProtocol Reads the startup telegram from the antenna moby_u_CheckDSR Checks the DSR signal on the interface moby_u_SetDTR Sets the DTR signal or resets it moby_u_ReadOTP Reads the complete OTP memory moby_u_WriteOTP Writes the complete OTP memory moby_u_ReadTagId Reads the TagId from the MDS

ppendix

Page 86

R 01.04

E-80

STG Hand-Held Terminal

(5)J31069-D0126-U001-A5.1-7418

A.3 ASCII Table

ppendix

Page 87

TO:

Siemens AG

A&D SE EWF MS

PO Box 2355

D-90713 Fuerth

FROM:

Yourname: __________________________

Yourtitle: __________________________

Yourcompany:_ _________________________

Street: __________________________

City: __________________________

Telephone: _________________________

Please tick your branch.

- Automotive industry

- Chemical industry

- Electrical industry

- Foodstuffs

- Process control technology

- Mechanical engineering

- Petrochemistry

- Pharmaceutics industry

- Plastics processing

- Paper industry

- Textiles industry

- Transportation industry

- Other _____________

Page 88

If you encountered concrete problems, please use this space to explain.

_____________________________________

Remarks/Suggestions

Your remarks and suggestions help us to improve the quality of our documentation. Please complete this questionnaire as soon as you have time, and return it to Siemens.

Title of your manual:_______________________

Order number of your manual:_ __________________

Please enter your personal evaluation from 1 (good) to 5 (poor).

1. Do the contents of this manual meet your requirements ?

2. Is it easy to find the information you need ?

3. Is the information written in an easy-to-understand manner ?

4. Does the amount of technical detail meet your requirements ?

5. What is your opinion of the figures and tables ?

Page 89

Inhaltsverzeichnis

Allgemeines

Die Inbetriebnahme des STG

Die Bedienung des STG

Die Programme “MOBY D/E/F/I/U”

Das Programm “FILEHANDLER”

Erweiterte Funktionen

Die Programme “MOBY D/E/F/I/U” mit numerischer PSION-Version

Fehlermeldungen

Technische Daten

Anhang

erschienen im Januar 2004

(5)J31069-D0126-U001-A5.1-7418

Bedienungsanleitung

MOBY

Handterminal STG

Page 90

Sicherheitstechnische Hinweise

Dieses Handbuch enthält Hinweise, die Sie zu Ihrer persönlichen Sicherheit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise sind durch ein Warndreieck hervorgehoben und je nach Gefährdungsgrad folgendermaßen dargestellt:

Hinweis

ist eine wichtige Information über das Produkt, die Handhabung des Produktes oder den jeweiligen Teil der Dokumentation, auf den besonders aufmerksam gemacht werden soll.

Qualifiziertes Personal

Inbetriebsetzung und Betrieb eines Gerätes dürfen nur von qualifiziertem Personal vorgenommen werden. Qualifiziertes Personal im Sinne der sicherheits-

technischen Hinweise dieses Handbuchs sind Personen, die die Berechtigung haben, Geräte, Systeme und Stromkreise gemäß den Standards der Sicherheitstechnik in Betrieb zu nehmen, zu erden und zu kennzeichnen.

Bestimmungsgemäßer Gebrauch

Beachten Sie Folgendes:

Warnung

Das Gerät darf nur für die im Katalog und in der technischen Beschreibung vorgesehenen Einsatzfälle und nur in Verbindung mit von Siemens empfohlenen bzw. zugelassenen Fremdgeräten und -komponenten verwendet werden.

Der einwandfreie und sichere Betrieb des Produktes setzt sachgemäßen Transport, sachgemäße Lagerung, Aufstellung und Montage sowie sorgfältige Bedienung und Instandhaltung voraus.

Marken

MOBYR ist eine Marke der SIEMENS AG. Die übrigen Bezeichnungen in dieser Schrift können Marken sein, deren Benut-

zung durch Dritte für deren Zwecke die Rechte der Inhaber verletzen können.

Wir haben den Inhalt der Druckschrift auf Übereinstimmung mit der beschriebenen Hard-und Software geprüft. Dennoch können Abweichungen nicht ausgeschlossen werden, so dass wir für die vollständige Übereinstimmung keine Gewähr übernehmen. Die Angaben in dieser Druckschrift werden regelmäßig überprüft, und notwendige Korrekturen sind in den nachfolgenden Auflagen enthalten. Für Verbesserungsvorschläge sind wir dankbar.

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts ist nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte vorbehalten, insbesondere für den Fall der Patenterteilung oder GM-Eintragung.

Siemens AG Bereich Automation and Drives Geschäftsgebiet Special Products,

Projects Automotive Industry, Training

Postfach 4848, D-90327 Nürnberg

E Siemens AG 1999, 2000, 2002, 2003, 2004 Technische Änderungen bleiben vorbehalten.

Siemens Aktiengesellschaft Bestell-Nr. (5)J31069-D0126-U001-A5.1-7418

Page 91

A 01.04

D-I

Handterminal STG (5)J31069-D0126-U001-A5.1-7418

Inhaltsverzeichnis

1 Allgemeines D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Einsatzgebiete D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Produktbeschreibung D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Die Inbetriebnahme des STG D-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Mitgelieferte Komponenten D-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Der Zusammenbau D-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Einschalten des Gerätes und Einstellen der Betriebsart D-6. . . .

2.4 MOBY-Applikationen D-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 Bedienung D-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Die Bedienung des STG D-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Die Tastatur D-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 Die Antenne am Lesekopf und das Antennenfeld D-9. . . . . . . . . .

3.2.1 MOBY D/E/F/I D-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2.2 MOBY U D-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3 Bedienung der MOBY U-Antenne D-12. . . . . . . . . . . . . . . . . . . . . . . .

3.4 Die Ladefunktion D-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5 Akku-Pack der MOBY U-Antenne wechseln D-16. . . . . . . . . . . . . . .

4 Die Programme “MOBY D/E/F/I/U” D-17. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 Der Dateneditor D-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 Die MDS-Funktionen D-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.1 Allgemeines zu Lesen und Beschreiben eines MDS D-21. . . . . . . .

4.2.2 MDS lesen D-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.3 MDS beschreiben D-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.4 MDS löschen/Initialisieren D-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.5 MDS-Status lesen D-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.6 Lesen der ID-Nummer D-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.7 OTP-Speicher lesen D-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.8 OTP-Speicher beschreiben D-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2.9 Rohdaten lesen D-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3 Die Datei-Funktionen D-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.1 Laden einer Datei D-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.2 Speichern D-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3 Beenden D-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inhaltsverzeichnis

Page 92

A 01.04

D-II

Handterminal STG

(5)J31069-D0126-U001-A5.1-7418

4.4 Die Funktionen Editor D-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1 Sprung zur Adresse D-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.2 Anzeige D-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.3 Anzeige löschen D-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.4 Datum editieren D-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 Die Funktionen Extras D-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.1 Kommunikation D-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.2 Passwort D-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.3 Antenne D-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.4 Adressen Setup D-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.5 MOBY I Setup D-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.6 MOBY E Setup D-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.7 MOBY U Setup D-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5.8 SLG Status D-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6 Die Funktionen “?” D-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.1 Sprache D-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.2 Ueber D-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6.3 Version D-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Das Programm “FILEHANDLER” D-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Allgemeines zum Filehandler D-36. . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Die Filehandler-Befehle D-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Die Anzeigen Editor und Directory D-39. . . . . . . . . . . . . . . . . . . . . . .

5.3.1 Der Dateneditor im Filehandler D-39. . . . . . . . . . . . . . . . . . . . . . . . . .

5.3.2 Die Directory-Ansicht D-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 Die Datei-Funktionen D-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.1 Lese Datei vom MDS D-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.2 Lese Datei vom STG RAM D-42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.3 Schreibe Datei auf MDS D-42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.4 Schreibe Datei auf STG RAM D-43. . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.5 Lese Verzeichnis vom MDS D-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.6 Lese Verzeichnis vom STG RAM D-43. . . . . . . . . . . . . . . . . . . . . . . .

5.4.7 Beispiel: Kopieren von Dateien D-44. . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Das Befehle-Menü D-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.1 Datei neu D-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.2 Datei loeschen D-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.3 MDS formatieren D-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.4 Datei Attribut D-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.5 MDS Status D-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.6 MDS Cover D-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inhaltsverzeichnis

Page 93

A 01.04

D-III

Handterminal STG (5)J31069-D0126-U001-A5.1-7418

5.6 Die Funktionen Editor D-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.1 Anzeige Verzeichnis D-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.2 Anzeige Editor D-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.3 Datei Größe verändern D-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.4 Anzeige löschen D-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.5 Sprung an Adresse D-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.6 Anzeige Setup D-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7 Die Funktionen Extras D-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.1 Parameter D-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2 Passwort für Filehandler D-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.3 Kommunikation D-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8 Die Funktionen “?” D-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Erweiterte Funktionen D-52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Die Hinterlegung der MDS-Daten im Handterminal D-52. . . . . . . . .

6.2 Kopieren von MOBY-Daten von und zum Handterminal D-53. . . .

6.2.1 Was wird zusätzlich benötigt? D-53. . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2.2 Das Arbeiten mit dem PSION-Dateimanager D-53. . . . . . . . . . . . . .

6.2.3 Die Organisation der Datei READ.HEX D-56. . . . . . . . . . . . . . . . . . .

6.2.4 Die Organisation der Datei READ.HX1 D-56. . . . . . . . . . . . . . . . . . .

6.3 Funktionen mit dem PSION-Betriebssystem D-56. . . . . . . . . . . . . .

6.4 Paralleles Abarbeiten mehrerer Anwendungen D-57. . . . . . . . . . . .

6.5 Die automatische Stromsparfunktion D-58. . . . . . . . . . . . . . . . . . . . .

6.6 Anschluss von SIM-Geräten (MOBY E/I/V) D-58. . . . . . . . . . . . . . . .

6.7 System-RESET D-59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 Die Programme “MOBY D/E/F/I/U” mit numerischer

PSION-Version D-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 Fehlermeldungen D-61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.1 Fehlermeldungen bei den Programmen “MOBY D/E/F/I/U” D-62. .

8.2 Fehlermeldungen beim Programm “FILEHANDLER” D-66. . . . . . .

9 Technische Daten D-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A Anhang D-74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.1 Bestellung von Komponenten für erweiterte Funktionen D-74. . . .

A.2 Entwickeln von Anwenderapplikationen D-75. . . . . . . . . . . . . . . . . .

A.3 ASCII-Tabelle D-80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inhaltsverzeichnis

Page 94

A 01.04

D-IV

Handterminal STG

(5)J31069-D0126-U001-A5.1-7418

Inhaltsverzeichnis

Page 95

A 01.04

D-1

Handterminal STG (5)J31069-D0126-U001-A5.1-7418

1 Allgemeines

Das STG (Service- und Testgerät) erweitert die Identifikationssysteme MOBY D, MOBY E, MOBY F, MOBY I bzw. MOBY U um ein leistungsfähiges mobiles Handterminal (Basis: PSION Workaboutmx) für Applikationen in den Bereichen Logistik, Distribution und Service. Darüber hinaus ist es ein unentbehrliches Hilfsmittel bei der Inbetriebnahme und beim Test.

1.1 Einsatzgebiete

Das MOBY-Handterminal ist bei MOBY D, MOBY E, MOBY F, MOBY I und MOBY U einsetzbar. Das enthaltene Service- und Testprogramm gestattet ein einfaches Lesen und Beschreiben aller Datenspeicher von MOBY D, MOBY E, MOBY F, MOBY I oder MOBY U.

Darüberhinaus kann der Kunde sehr einfach seine eigene Applikation auf dem Handterminal programmieren. Eine C-Library für die Programmierung der Handterminal-Leseköpfe wird von Siemens angeboten. Damit werden Anwendungen im Bereich Lager, Logistik und Kommissionierung einfach realisierbar. Der Einsatz des Handterminals kann auch in rauher Umgebung erfolgen. Das Handterminal ist sehr robust und gegen Spritzwasser geschützt. Das Display ist gut lesbar. In dunklen Räumen kann eine Displaybeleuchtung zugeschaltet werden.

1.2 Produktbeschreibung

Das MOBY-Handterminal besteht aus einem Grundgerät und einem Lesekopf von MOBY D, MOBY E, MOBY F oder MOBY I bzw. einer Antenne von MOBY U. Das Grundgerät ist ein PSION Workaboutmx. Dieses Gerät ist weltweiter Standard bei Handterminals. Desweiteren gehört eine Memory Card mit dem MOBY Service- und -Testprogramm inkl. Bedienungsanleitung zum Lieferumfang. Die Memory Card wird in das Grundgerät eingesteckt. Das Serviceund Testprogramm startet sich beim Einschalten des Handterminal automatisch. Mit dem Handterminal können alle Datenspeicher von MOBY D, MOBY E, MOBY F, MOBY I oder MOBY U bearbeitet werden.

Allgemeines

Page 96

A 01.04

D-2

Handterminal STG

(5)J31069-D0126-U001-A5.1-7418

Folgende Funktionen können ausgeführt werden:

S Auslesen der Daten aus dem MDS S Schreiben der Daten in den MDS S Löschen des gesamten Datenspeichers (Beschreiben mit einem Füllwert) S Lesen und Anzeigen der ID-Nummer des MDS (MOBY D/E/F/U) S MDS-Status lesen (MOBY U) S Daten vom OTP-Speicher lesen (MOBY U) S Daten auf OTP-Speicher schreiben (MOBY U) S Darstellen und Editieren der Daten in Hexadezimal und ASCII S Passwortschutz ein- und ausschaltbar für alle schreibenden Funktionen und

zum Beenden des MOBY-Programms

S Menüführung in verschiedenen Sprachen (zzt. Deutsch und Englisch) S Abspeichern der gelesenen MOBY-Daten in Dateien. Dafür stehen im

Handterminal ca. 1,8 MB zur Verfügung.

Zusätzliche Funktionen bei MOBY I-Filehandler:

S Formatieren des MDS S Anlegen von Dateien auf dem MDS S Beschreiben von Dateien auf dem MDS S Lesen von Dateien auf dem MDS S Auslesen und Anzeigen der Directory S Löschen von Dateien auf dem MDS

Der Schreib-/Lesekopf von MOBY D/E/F/I wird einfach mit dem PSION-Grundgerät verschraubt. Er besitzt eine serielle TTL-Schnittstelle für die Kommunikation mit dem Grundgerät. Die Spannungsversorgung des Lesekopfes liefert das Grundgerät. Die Antenne von MOBY U und das PSION-Grundgerät werden über eine Schiebemechanik gekoppelt. Die Kommunikation erfolgt über die RS 232Schnittstelle. Die Spannungsversorgung der Antenne liefert ein integrierter Akku-Pack. Der Schreib-/Lesekopf oder die Antenne und das STG-Programm können auch einzeln bestellt werden. Damit ist es möglich, dass der Kunde ein bereits vorhandenes PSION Workabout verwendet oder ein Workabout mit anderer Schnittstellen- und Tastatur-Konfiguration direkt von PSION bestellt und einsetzt.

Allgemeines

Page 97

A 01.04

D-3

Handterminal STG (5)J31069-D0126-U001-A5.1-7418

Das entsprechende Ladegerät (inkl. 230-V-Steckernetzteil) für das Wiederaufladen der Akkus muss gesondert bestellt werden.

S MOBY D/E/F/I

Das Ladegerät (Bestellnummer 6GT2 303-1DA00) ist für Wand- oder Fahrzeugmontage geeignet. Bei Fahrzeugmontage wird für die Ladefunktion ein PSION-Spezialkabel benötigt (siehe Anhang A.1).

S MOBY U

Die Akkus des Handterminals (im PSION Workabout und in der Antenne) werden mit dem Netzteil (Bestellnummer 6GT2 503-1DA00) geladen (siehe Kap. 3.4).

Für Applikationen steht dem Anwender eine C-Library mit den Funktionen des MOBY-Lesekopfes zur Verfügung. Mit der optionalen C-Entwicklungsumgebung für den PSION Workabout kann der Anwender eigene Programme entwickeln (vgl. Anhang A.2).

Allgemeines

Page 98

A 01.04

D-4

Handterminal STG

(5)J31069-D0126-U001-A5.1-7418

2 Die Inbetriebnahme des STG

2.1 Mitgelieferte Komponenten

Die Lieferung des STG besteht aus mehreren Komponenten. Diese sind auch einzeln im Lieferschein vermerkt:

Bestellte

Komponente

Bestellnummer

Packliste

Packnummer

MOBY D

6GT2 603-0AA00 PSION Workabout

A5E00016735

Handterminal

MOBY D-Lesekopf 6GT2 603-1AA00

STG

Memory-Card inkl. STG-Software und Bedienungsanleitung

6GT2 303-1CA00

NiCd-Akku 6GT2 094-0AB00

MOBY E

6GT2 303-0AA00 PSION Workabout

A5E00016735

Handterminal

MOBY E-Lesekopf 6GT2 303-1AA00

STG

Memory-Card inkl. STG-Software und Bedienungsanleitung

6GT2 303-1CA00

NiCd-Akku 6GT2 094-0AB00

MOBY F

6GT2 403-0BA00 PSION Workabout

A5E00016735

Handterminal

MOBY F-Lesekopf 6GT2 403-1BA00

STG

Memory-Card inkl. STG-Software und Bedienungsanleitung

6GT2 303-1CA00

NiCd-Akku 6GT2 094-0AB00

MOBY I

6GT2 003-0CA00 PSION Workabout

A5E00016735

Handterminal

MOBY I-Lesekopf 6GT2 003-1CA00

STG

Memory-Card inkl. STG-Software und Bedienungsanleitung

6GT2 303-1CA00

NiCd-Akku 6GT2 094-0AB00

Die Inbetriebnahme des STG

Page 99

A 01.04

D-5

Handterminal STG (5)J31069-D0126-U001-A5.1-7418

Bestellte

Komponente

Packnummer

Packliste

Bestellnummer

MOBY U

6GT2 503-0AA00 PSION Workabout

A5E00016735

Handterminal

MOBY U-Antenne 6GT2 503-1AA00

STG

Memory-Card inkl. STG-Software und Bedienungsanleitung

6GT2 303-1CA00

NiCd-Akku 6GT2 094-0AB00

2.2 Der Zusammenbau

Folgende Punkte sind nacheinander auszuführen:

S Knopfzelle einsetzen; die Knopfzelle liegt in einer Vertiefung in der Ver-

packung des PSION Workabout

S Akkus einlegen; die Nase an den Akkus muss dabei nach links zeigen S Den Flash-Programmspeicher mit der STG-Anwendung in den oberen

Schacht (A) einstecken

S Den Lesekopf aufstecken und verschrauben (MOBY D/E/F/I) S Die Antenne und das PSION Workabout zusammenfügen (MOBY U)

– Das PSION Workabout mit 4 Schrauben auf den Metallrahmen schrau-

ben.

– Den SubminD-Stecker der MOBY U-Antenne auf die RS 232-Schnittstelle

des PSION Workabout stecken und festschrauben.

– Das PSION Workabout in die Führungsschiene der oberen Gehäuse-

schale der Antenne einschieben, bis die Verriegelungsmechanik einrastet.

Damit ist der Zusammenbau abgeschlossen.

Die Inbetriebnahme des STG

Page 100

A 01.04

D-6

Handterminal STG

(5)J31069-D0126-U001-A5.1-7418

2.3 Einschalten des Gerätes und Einstellen der Betriebsart

Hinweis

Bevor Sie das Gerät einschalten, müssen Sie das Handterminal in das Ladegerät stecken (MOBY D/E/F/I) oder mit dem Netzteil (6GT2 503-1DA00) verbinden (MOBY U) und mindestens 14 Stunden aufladen (siehe Kap. 3.4).

Danach ist das Handterminal betriebsbereit. Nach dem Einschalten dauert der erste Hochlauf einige Sekunden. Die

MOBY-Anwendung startet automatisch. Es erscheint ein Auswahlmenü mit den MOBY-Applikationen. Wählen Sie die MOBY-Applikation entsprechend dem RF-Schreib-/Lesekopf oder der Antenne aus, den/die Sie betreiben möchten.

1) MOBY-Filehandler für MOBY I. Der Zugriff auf die MDS-Daten erfolgt über Filenamen (siehe Kap. 5).

2)-6)Normales MOBY Service- und Testprogramm für MOBY D/E/F/I/U. Der Zugriff auf die MDS-Daten erfolgt über physikalische Adressen (siehe Kap. 4).

9) Über “Exit” gelangen Sie auf die Betriebssystemebene des Handterminals.

V) Versionsanzeige “MOBY Applikations-

menü” (wird nicht im Auswahlmenü angezeigt)

Das Gerät schaltet sich automatisch ab, nachdem für 5 Minuten keine Taste gedrückt wurde. Nach dem Wiedereinschalten arbeitet das Handterminal mit der gleichen Maske weiter, in der es sich befand, bevor es manuell oder automatisch abgeschaltet wurde (siehe Kap. 6.5).

Die Inbetriebnahme des STG

Siemens MOBY series, MOBY E, MOBY D, MOBY U, MOBY F User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual