Siemens GIGASET C610A, GIGASET C610 Quick start guide

Gigaset C610-C610A, QUG, Grossbritannien, A31008-M2325-L101-1-7643

GIGASET HELPLINE: 0845 3670812

Quick Start Guide

21
3
45
7
6
8

1 one Gigaset C610A base 2 one mains adapter 3 one Gigaset C610H handset 4 one phone cord 5 two batteries

6 one battery cover 7 one belt clip 8 one user guide

plus one quick start guide
9J
1
1
1
2
¤ Plug the mains adapter into the plug
socket
2.
¤ Connect the flat plug from the mains
adapter
1.
If you need to disconnect the plug from the charg­ing cradle, press the release button
3 and discon-
nect the plug
4.
1
2
4
3
Issued by Gigaset Communications GmbH Frankenstr. 2a. D-46395 Bocholt
© Gigaset Communications GmbH 2011 All rights reserved. Subject to availability. Rights of modification reserved. www.gigaset.com
A31008-M2325-L101-1-7643
¤ Insert the batteries the right
way round. The polarity is indicated in/on the battery compartment.
¤ First insert the battery cover at
the top
a.
¤ Then press the cover b until it
clicks into place.

If you need to open the battery cover, for instance to replace the batteries, place your fingertip in the cavity on the casing and pull the battery cover upwards.

a
b
¤ Place the handset in the base/charging cradle for
10 hours.
¤ Then remove the handset
from the base/charging cradle and do not replace it until the batteries are fully discharged.
10 h
Date/Time
Date:
14.10.2009
Time:
00:00
Date/Time
Date:
31.01.2011
Time:
00:00
¤ Press the key below §Time§ on the
screen display to open the input field.

The Date/Time submenu is shown on the display.

¤ The active input position flashes.
Enter day, month and year as an 8-digit number via the keypad, e.g. 4Q 2Q for 14/10/2011.
Calls Time
Press the right or left control key to change the input position and cor­rect an entry.
¤ Enter the hours and minutes as
four digit numbers via the keypad, e.g. QM5 for 07:15 am. Change the input position with the control key if necessary.
¤ Press down on the control key to switch to the
time input field.
¤ Press the key below §Save§ on the display
screen to confirm your entry.
The display shows Saved. You will hear a con­firmation tone and the handset will automat­ically return to idle status.
Back Save
Date/Time
¿
Saved
i Ã
¤
V
07:15
INT 1 14 Oct
Calls SMS

Pack contents

Connecting the base station

¤ First connect
the mains
1.
adapter
¤ Then connect
the telephone
2 and
jack insert the cables into the cable ducts.

Please note:

u The mains
adapter must always be connected, as the phone will not operate without a mains connection.
u Only use the mains adapter and phone cord supplied. Pin connections on tele-
phone cables can vary.
u The LED display should light up at the base station. If not, please
ensure the power lead is fully inserted.

Connecting the charging cradle (if included)

Final check list

To ensure your product is set up correctly please check the following

u Have you used phone cord supplied u Have you fully inserted the power cable into base station u Have you inserted batteries correctly u Have you charged the batteries for 10 hours u Have you set up Date/Time

PLEASE NOTE:

For a dial tone press the call button c for approx. 2 seconds. Short press opens redial list.

Message Indication Key events:
u missed calls (if caller ID is enabled for your line numbers will be shown) u new messages on the answering machine (also indicated by flashing message
counter on base station)
u new Text messages (SMS) received

If you have problems setting up or operation this product please call

GIGASET HELPLINE 0845 3670812

f on handset will flash to indicate one or all of the following

Preparing the handset

Initial charging and discharging of the batteries

The correct charge level can only be displayed if the batteries are first fully charged and discharged.

If you have purchased a model with multiple handsets the package should contain two bat­teries, a battery cover, a belt clip and a charging cradle mains adapter tional handset.
9 with
J for each addi-

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm can be used.

Setting the date and time

Display in idle status

u Reception signal between the base and handset:
– good to poor: ÐiÑÒ –no reception: | flashes Green: Eco Mode activated
Ã
u
: answering machine is activated
u Battery charge status:
yy{{ (empty to full) – y flashes red: batteries almost empty – xyx{x{ (charging)
u INT 1: Internal name of the handset
If Eco Mode+ is activated, the ¼ icon is displayed in the top left (see chapter “ECO DECT” of user manual.

Frequently asked questions

Q: There is no dial tone.

A: Press call button for 2 seconds (long press) to obtain dial tone. A short press opens
the redial list.

Q: The line is crackling / not clear.

A: Have you used the new line cable provided? Please do not use an old cable.

Q: Message indicator flashing on handset and I cannot retrieve my message.

A: Message indicator will flash to indicate missed call as well as new message or text
message. Please check it is not indicating a new missed call or text message.

Q: The caller ID is not functioning.

A: Have you subscribed to this service (CLIP) from your provider?

Q: Can I record my own announcement on the answer machine.

A: Yes. Please refer to Chapter
“Operating the answer machine of the Gigaset C610A base station” of your user manual (p. 47).

Q: The display is not clear.

A: The display is protected by a plastic film, please make sure you have removed the
protective film.

Q: The handset is not registered.

A: If your handset is not registered, please refer to Chapter “Registering handsets”
of your user manual (p. 55) to instructions how to register handsets manually.
For more QUESTIONS AND ANSWERS please refer to chapter “Service (Customer
Care)” of user manual (p. 69).
Loading...