Sharp XL-HP737E User Manual

MODEL

XL-HP737E

MICRO COMPONENT SYSTEM

This Quick Start Guide will help you to correctly install and oper­ate your system.

If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/customersupport.
Customers without Internet access may telephone
08705 274277 during office hours (or [phone]
if telephoning from Ireland).

2

Remote control battery installation

0301

1

Accessories

Remote control × 1

FM aerial × 1

3

System connections

FM aerial

AM loop aerial × 1

AM loop aerial

Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.

1 Remove the battery cover.

2 Insert the batteries as shown.

3 Replace the cover.

4

Turning on your system

The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.

Right speaker

Wall socket
(AC 230 V, 50 Hz)

1 Press the X-BASS/DEMO button to

cancel the demonstration mode.

Left speaker

2 Press the ON/STAND-BY button to

turn the power on.

Red

Black

TINSEA054AWZZ
04A R YT 1

XLHP737E_QG.pm 04.1.27, 3:49 PM1

Listening to a CD or MP3 disc

1 Press the CD button.
2 Press the 1 button and within 5 seconds, press the

OPEN/CLOSE button to open the disc tray 1.

3 Place the disc on the disc tray 1, label side up.

12 cm (5”)

8 cm (3”)

Listening to the radio

1 Press the TUNER (BAND) button repeatedly to select the

desired frequency band (FM or AM).

2 Press the TUNING ( or ) button to tune in to the desired

station.
When the TUNING button is pressed for more than 0.5 sec­onds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.

To receive an FM stereo transmission:

Press the TUNER (BAND) button to display the “ST” indicator.

” will appear when an FM broadcast is in stereo.

● “

4 Press the OPEN/CLOSE button to close the disc tray 1.
5 You can place discs on trays 2 - 5 by following steps 2 - 4.
6 Press the / button to start playback.

Listening to a cassette tape

1 Press the TAPE button.
2 Open the cassette door by pushing the area marked “

PUSH EJECT”.

FM stereo mode indicator

FM stereo receiving indicator

■

If trouble occurs

When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.

If such a problem occurs, do the following:

1. Set the unit to the stand-by mode and turn the power on
again.

2. If the unit is not restored in the previous operation, un­plug and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory
by resetting it.

■

Clearing all the memory (reset)

1. Press the ON/STAND-BY button to enter the power stand­by mode.

2. Whilst pressing down the button and the X-BASS/
DEMO button, press the
“CLEAR AL” appears.

PRESET button until

3 Load a cassette into the cassette compart-

ment with side A facing you.

4 Press the button to choose one side or

both sides.

5 Press the / button to listen to side A, or the button

for side B.

XLHP737E_QG.pm 04.1.27, 3:49 PM2

Caution:

This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.

■

Maintenance

Routine maintenance is required for continued optimum perfor­mance, refer to the operation manual (page 38).

TINSEA054AWZZ