SHARP VC-V10/19, VC-V30/50, VC-V59/70 Service Manual

SERVICE MANUAL

VC-V10/V19

VC-V30/V50

VC-V59/V70

SERVICE MANUAL

S99N7VC-V10//

SHARP

VIDEO CASSETTE PLAYER

VC-V10/19

SHARP

VC-V30

SHARP

VIDEO CASSETTE PLAYER

1. SPECIFICATIONS......................................................................................................................... 2

MODELS VC-V10/VC-V19/VC-V30/VC-V50/VC-V59/VC-V70

2. DISASSEMBLY AND REASSEMBLY............................................................................................3

3. FUNCTION OF MAJOR MECHANICAL PARTS ...........................................................................6

4. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS .......................... 8

5. ELECTRICAL ADJUSTMENT......................................................................................................27

6. MECHANISM OPERATION FLOWCHART AND TROUBLESHOOTING GUIDE ...................... 30

7. TROUBLESHOOTING.................................................................................................................36

8. BLOCK DIAGRAM....................................................................................................................... 46

9. SCHEMATIC DIAGRAM AND PWB FOIL PATTERN..................................................................52

10. REPLACEMENT PARTS LIST .................................................................................................... 83

11. EXPLODED VIEW OF MECHANICAL PARTS............................................................................92

12. PACKING OF THE SET .............................................................................................................. 96

VC-V50/59

SHARP

VC-V70

MODELS

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used.

CONTENTS

VC-V10/19 VC-V30/50 VC-V59/70

Page

SHARP CORPORATION

VC-V10/V19 VC-V30/V50 VC-V59/V70

PRECAUTIONS IN PART REPLACEMENT

When servicing the unit with power on, be careful to the section marked white all over. This is the primary power circuit which is live.

When checking the soldering side in the tape travel mode, make sure first that the tape has been loaded and then turn over the PWB with due care to the primary power circuit. Make readjustment, if needed after replacement of part, with the mechanism and its PWB in position in the main frame.

(1) Start and end sensors: D804 and D803

Insert the sensor's projection deep into the upper hole of the holder (LHLDZ1962AJ00). Referring to the PWB, fix the sensors tight enough.

(2) Photocoupler RH-FX0007GEZZ: IC901

Refer to the symbol on the PWB and the anode marking of the part.

(3) Cam switches A and B (RH-PX0253GEZZ): D807 and D806

Adjust the notch of the part to the white marker of the symbol on the PWB. Do not allow any looseness.

(4) Take-up and supply sensors (RH-PX0252GEZZ): D801 and D802

Be careful not to confuse the setting direction of the parts in reference to the symbols on the PWB. Do not allow any looseness.

(5) Diode bridge (RH-DX0083GEZZ): D901

Adjust the + marking of the part to the symbol's cathode marking on the PWB.

1. SPECIFICATIONS

Format: VHS PAL/MESECAM/NTSC standard(VC-V10/30/50/70)

VHS PAL/MESECAM/SECAM/NTSC standard(VC-V19/59)

Recording/Playback system: Rotary, slant azimuth two head LP helical scan system(VC-V10/30/50/70)

Rotary, slant azimuth two head helical scan system(VC-V19/59)

Video signal system: PAL/MESECAM 4.43Hz colour or monochrome signals : 625 lines

(VC-V10/30/50/70) PAL/MESECAM/SECAM colour or monochrome signals : 625 lines (VC-V19/59) NTSC 3.58Hz colour or monochrome signals : 525 lines

Maximum Recording/playback time: 240 min with E-240 tape at SP mode

480 min with E-240 tape at EP mode(VC-V10/30/50/70) 480 min with T-160 tape at LP mode(VC-V10/30/50/70)

Tape width: 12.7 mm

Tape speed: 23.39 mm/sec. (PAL/MESECAM)

33.35 mm/sec. (NTSC)

Antenna: 75 ohm unbalanced

RF output signal: UHF channel E30 – E39 (preset to E39)

Power requirement: AC110V–240V, 50/60Hz

Power consumption: 13 W (approx.)

Operating temperature: 5°C to 40°C

Storage temperature: –20°C to 60°C

Video output: 1.0 Vp-p, 75 ohm Audio output: Line: –8 dB, less than 1 kohm

Weight: 2.7 kg (approx. )

Dimensions: 360 (W) x 284.5 (D) x 94 (H) mm

Accessories included: 75 ohm coaxial cable

Operation manual Infrared remote control Battery (R6 (UM/SUM–3 or AA)) x 2 Mic(VC-V30/70)

* Design and specifications are subject to change without notice.

Note: The antenna must correspond to the new standard DIN 45325

(IEC 169 - 2) for combined UHF/VHF antenna with 75 ohm connector.

2. DISASSEMBLY AND REASSEMBLY

2-1 DISASSEMBLY OF MAJOR BLOCKS

VC-V10/V19 VC-V30/V50 VC-V59/V70

TOP CABINET : Remove 3 screws 1. FRONT PANEL : Remove 2 VR Knobs 2 at first(VC-

V30/70). Remove 2 screws 3 and 7 clips 4.

MIC VR PWB : Remove 1 screw 5 and 1 FFC 6. HOLDER (VC-V30/70)

XHPSD30P06WS0

XEPSD30P14XS0

MECHANISM/ : Remove 2 screws 7 and 2 screws MAIN PWB Remove 1 screw 9 from behind of the ASSEMBLY main frame. Remove 1 connector 0.

Lift the antenna terminal cover and take the assembly out of the main frame.

XEBSD30P12000

TOP CABINET

MECHANISM/ MAIN PWB

XEBSD30P12000

ASSEMBLY

ANTENNA TERMINAL COVER

MAIN FRAME

*MIC VR PWB HOLDER

XJPSD30P10WS0

*MIC VR KNOB

FRONT PANEL

*VC-V30/70 Only

VC-V10/V19 VC-V30/V50 VC-V59/V70

2-2 DISASSEMBLING THE MECHANISM/MAIN PWB ASSEMBLY

ANTENNA : Remove 1 Hook q, 1 screw w and 1 TERMINAL COVER

screw e(VC-V50/59/70 Only). Remove the H/A shield case.

LED PWB : Take it out of connector r. HOLDER MECHANISM : Remove 3 FFCs t and 1 harness y. CHASSIS/ Be carefull not to confuse the top CASSETTE and bottom of the FFC. HOUSING Remove the mechanism chassis assem- ASSEMBLY bly straight up from the main PWB with

care not to damage theirs urrounding parts.

XHPSD30P06WS0

CASSETTE HOUSING

CASSETTE : Remove 2 screws u. HOUSING SHIELD PLATE : Remove 1 screw i.

ANTENNA TERMINAL COVER

LX-HZ3087GEFN

H/A SHIELD CASE

XEBSD30P12000

VC-V50/59/70 Only

LED PWB HOLDER

VC-V30/70 Only

VC-V50/59/70 Only

SHIELD PLATE

MECHANISM CHASSIS

MAIN PWB

2-3 CARES WHEN REASSEMBLING

VC-V10/V19 VC-V30/V50 VC-V59/V70

INSTALLING THE CASSETTE HOUSING

When the cassette housing is installed on the mechanism, the initial setting is essential condition. There are two initial setting methods, namely electrical and mechanical.

1. Electrical initial setting

So as to perform initial setting of mechanism execute the Step 1 of Installation of cassette housing. After ascertaining the return to the initial setting position (*1) install the

Pulley feed gear

Screwdriver

Tilt mark (*1)

cassette housing. (Conditions: When mechanism and PWB have been installed)

2. Mechanical initial setting

Feed the pulley feed gear of loading motor with screw driver. After ascertaining the return to the initial set position (*1) install the cassette housing in the specified position. (This method is applied only for the mechanism.)

Casecon drive gear

Drive angle of cassette housing

INSTALLING THE MECHANISM ON PWB

Lower vertically the mechanism, paying attention to the mechanism edge, and install the mechanism with due care so that the parts are not damaged. So as to fix the mechanism to the main PWB install two housings. (Fit the antenna cover to one of them. For other, fix the vicinity of loading motor and solder joint side of main PWB.) Connect again the FFC cable (AA-MH, AD-ME, AH-MH) between the mechanism and the main PWB.

END SENSOR

REC TIP SWITCH (VC-V50/59/70 Only)

PARTS WHICH NEED PARTICULAR CARE

When installing the mechanism chassis on the PWB unit, take care so as to prevent deformation due to contact of mechanism chassis with REC TIP SW.

AE Connector

AC Connector

AL Connector

START SENSOR

MIC JACK(VC-V30/70 Only)

VC-V10/V19 VC-V30/V50 VC-V59/V70

3. FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW)

VC-V19/50/59/70 Only

1715

No. Function

1 Full erase head(VC-V19/50/59/70 Only) 2 Supply pole base ass’y 3 Tension arm 4 Idler wheel ass’y 5 Pinch drive lever ass’y 6 Supply reel disk 7 Supply main brake

No. Function

8 Take-up main brake

9 Pinch drive cam 10 A/C head ass’y 11 Reverse guide lever ass'y 12 Casecon drive gear 13 Take-up reel disk 14 Pinch roller lever ass’y

FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW)

VC-V10/V19 VC-V30/V50 VC-V59/V70

19 20

No. Function

15 Drum ass’y 16 Loading motor 17 Drum drive motor 18 Take-up pole base ass’y 19 Slow brake lever 20 Master cam 21 Capstan D.D. motor

No. Function

22 Reel belt 23 Clutch lever 24 Limiter pulley ass'y 26 Shifter

VC-V10/V19 VC-V30/V50 VC-V59/V70

4. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS

The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.

4-1 MECHANISM CONFIRMATION ADJUSTMENT JIG

So as to perform completely the mechanism adjustment prepare the following special jigs. So as to maintain the initial performance of the machine the maintenance and check are necessary. Utmost care must be taken so that the tape is not damaged. If adjustment needs any jig, be sure to use the required jig.

No. Jig ltem Part No. Code Configuration Remarks

This cassette torque meter is used for check-

1. Torque Cassette Meter JiGVHT-063 CZ

JiGTG0090 CM

Torque Gauge

JiGTG1200 CN

3. Torque Gauge Head JiGTH0006 AW

ing and adjusting the torque of take-up for measuring tape back tension.

These Jigs are used for checking and adjusting the torque of take-up and supply reel disks.

4. Torque Driver JiGTD1200 CB

Master Plane Jig and Reel Disk Height

5. Adjusting Jig

JiGRH0002 BR JiGMP0001 BY JiGSG2000 BS

Tension Gauge

JiGSG0300 BF

Pinch pressing force

7. JiGADP003 BK

measuring jig

Reverse guide height

adjustment box driver

Alignment Tape

Guide roller height

10. JiGDRiVERH-4 AP

adjustment driver

X value adjustment

11. JiGDRiVER-6 BM

gear driver Reverse Guide Height

12. JiGRVGH-F18 BU Adjusting Jig

JiGDRiVER11055

VROCPSV CK

When fixing any part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg)

These Jigs are used for checking and adjusting the reel disk height.

There are two gauges used for the tension measurements, 300 g and

2.0kg. This Jig is used with the tension

gauge. Rotary transformer clearance adjusting jig.

This Jig is used for height adjustment of the reverse guide (for reverse guide height adjustment).

These tape is especially used for electrical fine adjustment.

Video Audio HiFi Audio Track 625 Monoscope 7k — 49µm PAL Color Bar 1k — 49 µm

This screwdriver is used for adjusting the guide roller height.

For X value adjustment

This Jig is used for height adjustment of the reverse guide.

4-2 MAINTENANCE CHECK ITEMS AND EXECUTION TIME

Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine.

VC-V10/V19 VC-V30/V50 VC-V59/V70

Maintained

Parts

Guide roller ass’y Sup guide shaft Retaining guide Slant pole on pole base Full erase head A/C head

Upper and lower drum ass’y

Capstan D.D. motor Pinch roller

Reel belt

Tension band ass’y

500 hrs.

1000 hrs.

1500 hrs

2000 hrs

Possible symptom

encountered

Lateral noises Head occasionally blocked

Color and beating Small sound or sound

distortion Poor S/N ratio, no color

Poor flatness of the envelope with alignment tape

No tape running, uneven color

No tape running, tape slack

No tape running, tape slack, no fast forward/ rewind motion

Screen swaying

Remarks

Abnormal rotation or significant vibration requires replacement.

Clean tape contact part with the specified cleaning liquid.

Clean tape contact area with the specified cleaning liquid.

Clean rubber and rubber contact area with the specified cleaning liquid.

Loading motor Idler ass’y

Limiter pulley Supply/take-up main brake levers

Cassette not loaded or unloaded

No tape running, tape slack

Tape slack

NOTE : Part replacement. : Cleaning : Apply grease <Specified> Cleaning liquid Industrial ethyl alcohol

* This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found,

clean or replace parts.

Video head cleaning procedure

1. Apply one drop of cleaning liquid to the cleaning paper with the baby oiler.

2. Gently press the cleaning paper against the video head to fix your finger, and move the upper drum so that each head is passed to and fro 5 times (do not move the cleaning paper).

3. Wipe with the dry cleaning paper.

Notes :

• Use the commercially available ethanol of Class 1 as cleaning liquid.

• Since the video head may be damaged, do not move up and down the cleaning paper.

Gently press the cleaning paper to fix with your finger, and rotate the upper drum to clean. Move to and fro 5 times for each head. (Do not move the cleaning paper.)

Rotate the upper drum with one hand.

• Whenever the video head is cleaned, replace the cleaning paper.

• Do not apply this procedure for the parts other than the video head.

Parts Code Description Code ZPAPRA56-001E Cleaning Paper AW ZOiLR-02-24TE Babe Oiler (Spoit) AH

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-3 REMOVING AND INSTALLING THE CAS-

SETTE HOUSING

• Removal

1. In the cassette removing mode, remove the cassette.

2. Unplug the power cord.

3. Remove in the following numerical order. a) Remove two screws 1. b) Slide and pull up the cassette housing control.

Notes:

1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care.

2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated).

3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum.

4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum.

5. After installing the cassette housing control once perform cassette loading operation.

4-4 TO RUN A TAPE WITHOUT THE CASSETTE

HOUSING CONTROL ASSEMBLY

1. Remove the full-surface panel.

2. Short-circuit TP701.

3. Plug in the power cord.

4. Turn off the power switch.

(The pole bases move into U.L.position.)

5. Open the lid of a cassette tape by hand.

6. Hold the lid with two pieces of vinyl tape.

7. Set the cassette tape in the mechanism chassis.

8. Stabilize the cassette tape with a weight (500g) to

prevent floating.

9. Turn on the power switch.

10. Perform running test.

Figure 4-1.

• Reassembly

1. Before installing the cassette housing control, shortcircuit TP701 provided at the center (when facing to the main PWB), press the eject button. The casecon drive gear turns and stops when the positioning mark appears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below.

Casecon drive gear

Casecon drive angle gear

500g

Weight to prevent float (500g)

Mechanism chassis

Figure 4-3.

Note:

The weight should not be more than 500g. To take out the cassette tape.

1. Turn off the power switch.

2. Take out the cassette tape.

Figure 4-2.

2. Install in the reverse order of removal.

4-5 REEL DISK REPLACEMENT AND HEIGHT

CHECK

• Removal

1. Remove the cassette housing control assembly.

2. Pull the tension band out of the tension arm ass'y.

3. Remove the Supply/Take-up main brake ass'y.

4. Open the hook at the top of the reel disk, and remove the

reel disk.

Note:

Take care so that the tension band ass'y and main brake ass'y (especially soft brake) are not deformed.

Tension arm ass'y

Supply main brake ass'y

Tension band ass'y

Take-up main brake ass'y

VC-V10/V19 VC-V30/V50 VC-V59/V70

4. Assemble the Supply main brake ass'y.

Notes:

1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere.

2. Do not damage the Supply main brake ass'y. Be careful so that grease does not adhere to the brake surface.

• Reassembly (Take-up reel disk)

1. Clean the reel disk shaft and apply grease (SC-141) to it.

2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft.

3. Check the reel disk height and reassemble the take-up main brake ass'y.

Note:

1. Take care so that the Take-up main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface.

2. After reassembly, check the video search rewind back tension (see 4-10), and check the brake torque (see 4-

14).

Supply reel disk

Take-up reel disk

Figure 4-4.

Note:

When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed.

• Height checking and adjustment Note:

1. Set the master plane with due care so that it does not contact the drum.

2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage.

Master plane

Reverse guide

Supply reel disk

Cassette lock release shaft

Take-up reel disk

Position pin

Figure 4-6.

Figure 4-5.

• Reassembly (Supply reel disk)

1. Clean the reel disk shaft and apply grease (SC-141) to it.

2. Match the phases of reel disk and reel relay gear, and set the new reel disk.

3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y.

Note:

• Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk.

VC-V10/V19 VC-V30/V50 VC-V59/V70

Note:

Whenever replacing the reel disk, perform the height checking and adjustment.

Master plane

10 ± 0.2mm

Reel disk

Reel disk height adjusting jig

Mechanism chassis

Figure 4-7.

4-6 CHECKING AND ADJUSTMENT OF TAKE-

UP TORQUE IN FAST FORWARD MODE

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.

2. Press the FF button.

3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode.

• Checking

1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction.

2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).

Torque gauge

Notes:

1. Hold the torque gauge by hand so that it is not moved.

2. Do not keep the reel disk in lock state. Do not allow longtime measurement.

4-7 CHECKING AND ADJUSTMENT OF TAKE-

UP TORQUE IN REWIND MODE

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Set a torque gauge to zero on the scale. Place it on the supply reel disk.

2. Press the rewind button.

3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode.

• Checking

1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction.

2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).

Torque gauge

30mN·m (306gf·cm) or more

CCW

The gauge is held at its maximum value. (Red mark)

30mN·m (306gf·cm) or more

Idler ass'y

The gauge is held at its maximum value. (Red mark)

Figure 4-8.

• Adjustment

1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, and check again.

2. If the torque is less than the set value, replace the reel belt.

Supply reel disk

Idler ass'y

Figure 4-9.

• Adjustment

1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque.

2. If the winding-up torque is still out of range, replace the drive belt.

Notes:

1. Hold the torque gauge by hand so that it is not moved.

2. Do not keep the reel disk in lock state. Do not allow longtime measurement.

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-9 CHECKING AND ADJUSTMENT OF TAKE-

UP TORQUE IN VIDEO SEARCH REWIND MODE

• Remove the cassette housing control assembly.

4-8 CHECKING AND ADJUSTMENT OF TAKE-

UP TORQUE IN RECORD/PLAYBACK MODE

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Turn off the power switch.

• Open the cassette torque meter lid, and fix it with tape.

• Load the cassette torque meter into the unit.

• Put the weight (500g) on the cassette torque meter.

• Turn on the power switch.

• Press the picture record button, and set LP picture record mode (x2).

Set value LP6.9 ± 2.5mN⋅m (70 ± 25gf⋅cm)

500g

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

Press the playback button and rewind button to set the video search rewinding mode.

• Checking

Place the torque gauge on the supply reel disk, and turn it counterclockwise very slowly (one rotation every 1 to 2 seconds) and check that the torque is within the set value

14.0 ± 3.9mN⋅m. (144 ± 40gf⋅cm)

Torque gauge

CCW

Cassette torque meter

Figure 4-10.

• Checking

1. Make sure that value is within the setting 6.9±2.5mN·m (70±25gf·cm).

2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting.

3. Set the LP record mode (x2) and make sure that the winding-up torque is within setting.

• Adjustment

If the playback winding-up torque is not within the setting, replace the limiter pulley assembly.

Note:

When the torque cassette is set, put a weight (500g) to prevent rise. When the cassette torque meter is taken out. Turn off the power switch.

Supply reel disk

Figure 4-11.

Note:

Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible.

• Adjustment

If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly.

Note:

The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of fluctuation as setting.

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-10 CHECKING THE VIDEO SEARCH REWIND

BACK TENSION

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Checking

1. After pressing the play button, press the rewind button, and set the video search rewind mode.

2. Place the torque gauge on the take-up reel disk, and turn it counterclockwise very slowly (one rotation every 2 to 3 seconds) and check that the torque is within the set value 3.4±1.5mN⋅m (35± 15gf⋅cm).

Torque gauge

CCW

Take-up reel disk

Pinch roller

Capstan shaft

Tension gauge adapter

Tension gauge 900 - 1,200gf

Figure 4-13.

1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage.

2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction.

3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft.

4. Make sure that the measured value is within setting 9.0 to 11.8 N (900 to 1,200gf).

Figure 4-12.

Notes:

Set the torque gauge securely on the take-up reel disk. If it is not secure, the measurement will be incorrect.

4-11 CHECKING THE PINCH ROLLER PRESSURE

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Checking

Press the play button to set the playback mode.

4-12 CHECKING AND ADJUSTMENT OF

TENSION POLE POSITION

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Turn off the power switch.

2. Open the cassette tape (E-180), and fix with tape.

3. Set the cassette tape in loading state.

4. Put the weight (500g) on the cassette tape.

5. Turn on the power switch.

6. Make the adjustment with the beginning of a E-180 tape.

(E-180)

500g

Weight to prevent float (500g)

Figure 4-14.

• Checking

1. Set a cassette tape, push the REC button to place the unit in the SP record mode. Now check the tension pole position.

2. Visually check to see if the right edge of the tension pole is within the 2.3 ± 0.25 from the right edge of the Sup guide shaft.

VC-V10/V19 VC-V30/V50 VC-V59/V70

Tension pole adjuster adjusting range

Tension pole adjuster

Sup guide shaft

Tension pole

2.3 ± 0.25

Make the adjustment with the beginning of a E-180 tape.

Figure 4-15.

At left side from the center line

2.3 ± 0.25

Figure 4-16.

Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise.

90°

Figure 4-18.

Adjust so that the delta mark of tension pole adjuster is within 90° range (left, right).

4-13 CHECKING AND ADJUSTMENT OF

RECORD/PLAYBACK BACK TENSION

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Turn off the power switch.

2. Open the torque cassette meter and fix with tape.

3. Set the cassette tape in loading state.

4. Put the weight (500g) on the cassette torque meter.

5. Turn on the power switch.

At right side from the center line

2.3 ± 0.25

Figure 4-17.

Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise.

500g

Weight to prevent float (500g)

Cassette torque meter

Figure 4-19.

• Checking

1. Push the REC button to place the unit in the SP record mode.

2. At this time ascertain that the back tension is within the setting (36.5 to 52g·cm) by seeing the indication of torque cassette meter.

VC-V10/V19 VC-V30/V50 VC-V59/V70

• Adjustment

1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A.

2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.

Tension arm

Tension spring

• Checking the brake torque at the take-up side

Torque gauge

Take-up reel disk

CCW

Figure 4-20.

4-14 CHECKING THE BRAKE TORQUE

• Checking the brake torque at the supply side

Torque gauge

CCW

CCW: 2.9~9.8mN⋅m (30~100gf⋅cm) CW: 4.9~13.7mN⋅m (50~140gf⋅cm)

Figure 4-21.

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Set a torque gauge to zero on the scale. Place it on the supply reel disk.

2. Switch from the FF mode to the STOP mode.

3. Disconnect the power cord.

• Checking

Turn the torque gauge at a rate of about one turn/2 sec in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 4.9 to 13.7mN·m (50 to 140gf·cm); CCW direction: 2.9 to 9.8mN·m (30 to 100gf·cm).

Supply reel disk

CCW: 4.9~13.7mN⋅m (50~140gf⋅cm) CW: 3.9~10.8mN⋅m (40~110gf⋅cm)

Figure 4-22.

• Remove the cassette housing control assembly.

• After short-circuiting TP701 provided at the center (facing to the main PWB), plug in the power cord.

• Setting

1. Switch from the FF mode to the STOP mode.

2. Disconnect the power cord.

3. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.

• Checking

1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 4.9 to 13.7mN·m (50 to 140gf·cm), CW direction: 3.9 to 10.8 mN·m (40 to 110gf·cm).

2. Adjustment of the brake torque at the supply side and the take-up side

• Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque.

• If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring.

4-15 REPLACEMENT OF A/C (Audio/Control)

HEAD

1. Remove the cassette housing control assembly.

2. In unloading state unplug the power cord.

• Removal

1. Remove the screws 123, Azimuth screw, Tilt screw.

2. Unsolder the PWB fitted to the A/C head.

Notes:

1. When replacing, never touch the head. If you touched, clean with the cleaning liquid.

2. When removing the screw 3, take care so that the spring may out.

Tilt screw

Azimuth screw

Height screw

Spring

VC-V10/V19 VC-V30/V50 VC-V59/V70

3. Align the left end of gear of A/C head arm with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head arm. Tentative tightening torque must be 0.15 to 0.20 N·m (1.5 to 2.0kgf·cm).

Height screw

Left end of A/C head arm gear

Punched line mark on chassis

Figure 4-25.

Note:

1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken.

2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in 4-18.)

Figure 4-23.

• Replacement

1. Solder the removed PWB to the new head assembly.

2. Adjust the height from the A/C head arm (lower surface) to the A/C head plate to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw section and A/ C head front section) (See the figure below.)

Solder

New A/C head ass'y

A/C head PWB

Never touch the head

A/C head plate

Figure 4-24.

10.8mm10.8mm

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-16 A/C HEAD HEIGHT ROUGH ADJUSTMENT

• Setting

Azimuth screw

4-17 HEIGHT ADJUSTMENT OF REVERSE

GUIDE

1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38 mm, using the reverse guide height adjustment jig, in tape loading state. (Refer to Figure 4-28 (a) (b).)

Height screw

500g

Weight to prevent float (500g)

Tilt screw

Cassette tape

Mechanism chassis

Figure 4-26.

1. Set the cassette tape in the unit.

2. Press the PLAY button to put the unit in the playback mode.

3. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below.

A/C head

Reverse guide Reverse guide height adjusting jig

Mechanism chassis

(a)

Reverse guide height adjusting jig

13.38mm

(b)

Figure 4-28.

2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER

11055)).

Box driver

CCW

Height adjusting nut

Tape

0.3mm

Figure 4-27.

• Adjustment

Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape.

Figure 4-29.

3. Set the tape, and check for tape crease near the reverse guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 4-

30.)

500g

Weight to prevent float (500g)

Mechanism chassis

Reverse guide

Capstan motor shaft

Fixing guide

An example of crease near the reverse guide

* Check for crease from the A direction.

Figure 4-30.

4-18 ADJUSTMENT OF TAPE DRIVE TRAIN

1. Tape run rough adjustment

1 Remove the cassette housing control assembly. 2 After shortcircuiting TP701 provided at the center

(facing to the main PWB), plug in the power cord.

3 Check and adjust the position of the tension pole.

(See 4-12.)

4 Check and adjust the video search rewind back

tension. (See 4-10.)

5 Connect the oscilloscope to the test point for PB

CHROMA envelope output (TP201). Set the synchronism of the oscilloscope to EXT. The PB CHROMA signal is to be triggered by the head switching pulse (TP202).

6 Set the alignment tape (VROCPSV) to play. (Put a

500g weight on the cassette tape to prevent lift of cassette tape.)

Guide roller

Cassette Tape

500g

Weight of 500g

Figure 4-31.

7 Press the tracking button (+), (–) and change the

envelope waveform from max to min and from min to max. At this time make sure that the envelope waveform changes nearly parallel.

8 Unless the envelope waveform changes nearly par-

allel, adjust the height of supply side and take-up side guide roller so that the envelope waveform changes nearly parallel. (For envelope adjustment procedure refer to Figure 4-35.)

9 Turn the tilt screw to remove the tape crease at the

fixing guide flange. Playback the tape and check for tape crease at the fixing guide flange. (1)If there is no tape crease

Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears.

(2)If there is tape crease

Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange.

VC-V10/V19 VC-V30/V50 VC-V59/V70

Notes:

1. Previously set the tracking control in the center position, and adjust the envelope waveform to maximum with X value adjustment nut. Thereby the tape run rough adjustment is facilitated.

2. Especially the outlet side envelope waveform must have higher flatness.

Figure 4-32.

2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the

method stated in "4-15 Replacement 3".

2 Connect the oscilloscope to the audio output termi-

nal.

3 Using the alignment tape in which 1 kHz linear audio

signal has been recorded, adjust the height screw so as to get max audio output.

4 Using the alignment tape in which 7 kHz linear audio

signal has been recorded, adjust the azimuth screw so as to get max audio output.

5 The adjustment of 3 and 4 twice or three times

repeat, and finally adjust 4.

For X value adjustment Adjust the X value, turning the geartype screwdriver.

Figure 4-33.

3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA envelope

output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switching pulse).

2 Rough adjustment of X value

Tentatively fix A/C head arm screws 1 and 2 by the method described in 4-15 "Replacement 3". Playback the alignment tape (VROCPSV). Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Figure 4-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: When the A/ C head is adjusted, adjust so that the maximum envelope waveform is obtained nearest the position of initial setting made in 4-15.)

VC-V10/V19 VC-V30/V50 VC-V59/V70

3 Next, press the tracking button (+), (–) and change

4 If the tape is lifted or sunk from the helical lead

5 Press the tracking button (+), (–) and make sure that 6 Finally check tape crease near the reverse guide. If

the envelope waveform from max to min and from min to max. At this time adjust the height of supply and take-up side guide roller with the adjustment driver (JiGDRiVERH-4) so that the envelope waveform changes nearly parallel.

surface, the PB CHROMA envelope waveform appears as shown in Figure 4-35.

the envelope waveform changes nearly parallel. tape crease is found, remove it as stated in 4-17

"HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3.

Supply side

Take-up side Supply side Take-up side

PB CHROMA Envelope

CH-1 CH-2

Head switching pulse

Figure 4-34.

4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the

method described in 4-15 "Replacement 3".

2 Playback the alignment tape (VROCPSV).

When the tape is below the helical lead.When the tape is above the helical lead.

Adjustment

Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.

Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.

Figure 4-35.

3 Move the A/C head with the X value adjustment gear

driver by the method shown in Figure 4-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: At this time adjust so as to get the maximum envelope waveform nearest the A/C head position which has been set in case of X value rough adjustment as stated in 4-18, 3- 2.)

4 Tighten finally the screws 1 and 2. Be sure to

tighten at first the screw 1 and then the screw 2. Final tightening torque is 0.6N·m (If the screw 2 is tightened first, the X value may deviate.)

5 Adjust the playback switching point (Refer to the

electric adjustment method.)

6 Playback the self-picture-recorded tape, and check

the flatness of envelope waveform and sound.

Supply side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the envelope.

Take-up side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the envelope.

Notes:

When the A/C head X value adjustment is performed, be sure to perform at first X value rough adjustment (refer to 4- 18, 3-2).

Figure 4-36.

4-19 REPLACEMENT OF THE CAPSTAN D.D.

(DIRECT DRIVE) MOTOR

• Remove the mechanism from the main PWB (refer to 22 item 1. When removing the mechanism from the main

PWB").

• Removal (Follow the order of indicated numbers.)

1. Remove the reel belt 1.

2. Remove the three screws 2.

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-20 REPLACEMENT OF DRUM D.D. MOTOR

1. Set the ejection mode.

2. Withdraw the main power plug from the socket.

• Removal (Perform in numerical order.)

1. Disconnect the FFC cable 1.

2. Unscrew the D.D. stator assembly fixing screws 2.

3. Take out the D.D. stator assembly 3.

4. Unscrew the D.D. rotor assembly fixing screws 4.

5. Take out the D.D. rotor assembly 5.

Capstan D.D. motor

control PWB

Reel belt

Capstan D.D. motor

Figure 4-37.

• Reassembly

1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws.

2. Install the reel belt.

Notes:

1. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the movement.

2. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in 4-18 item 2. If crease is found, adjust as stated in 4-17 "HEIGHT ADJUSTMENT OF REVERSE GUIDE".

Notes:

1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it.

2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.)

3. Be careful not to damage the upper drum or the video head.

4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y.

5. After installation adjust the playback switching point for adjustment of servo circuit.

D.D. stator ass'y

D.D. rotor ass'y

FFC

Upper drum

Figure 4-38.

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-21 REPLACING THE UPPER AND LOWER

DRUM ASSEMBLY

• Replacement (Perform in the numerical order)

1 Remove the motor as stated in 4-20. 2 Remove the drum earth brush ass’y 2. 3 Remove the drum base 3 from the upper and lower

drum assembly 1.

[Cares when replacing the drum]

1. Be careful so that the drum earth brush is not lost.

2. Do not touch directly the drum surface.

3. Fit gently the screwdriver to the screws.

4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care.

5. Make sure that the drum surface is free from dust, dirt and foreign substances.

6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment.

• Playback switching point adjustment

• X-position adjustment and check

• Standard and x-3 slow tracking adjustment

7. After replacing the drum clean the drum.

4-22 ASSEMBLING OF PHASE MATCHING

MECHANISM COMPONENTS

• Assemble the phase matching mechanism components in the following order.

1. Assemble the pinch roller assembly and pinch drive cam.

2. Mounting the shifter (on the back of the mechanism chassis).

3. Mounting the master cam (on the back of the mechanism chassis).

4. Assemble the connection gear, slow brake and loading motor parts.

• Pinch drive cam and pinch roller assembling

method.

(Place the following parts in position in numerical order.)

(1)Reverse drive lever 1 (2)Reverse guide spring 2 (3)Reverse guide lever ass’y 3 (4)Reverse guide height adjusting nut 4 (5)Pinch drive cam 5 (6)Pinch roller ass’y 6 (7)Open lever 7

Figure 4-40.

4 3

Figure 4-39.

1Insert Reverse Guide Lever Ass’y

VC-V10/V19 VC-V30/V50 VC-V59/V70

Insert reverse guide lever ass'y

2 Insert pinch drive cam

Turn the reverse guide lever assembly counterclockwise to the stopper.

Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis.

Pinch drive lever ass'y

Figure 4-41-1.

2Insert Pinch Roller/Pinch Double Action Lever Ass’y.

Pinch Roller Double Action Lever Ass'y

Phase Matching Point 2

Align here.

Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly.

3Insert Open Lever.

Open lever

Figure 4-41-2.

Figure 4-41-3.

VC-V10/V19 VC-V30/V50 VC-V59/V70

4-23 INSTALLING THE SHIFTER

Capstan D.D. motor

Reel pulley

Drum

1. Make sure that the loading gear is at the Phase-Matching point 1 as shown below.

2. Install, paying attention to insert point 5 and release point 3.

3. For the phase matching at the insert point 1, see the Phase-Matching point 2 as shown below.

4. Finally fix the inserts 1 and 4.

(Bottom side of mechanism chassis)

Figure 4-42.

Insert point 3

Insert point 2

Shaft 1

Phase-Matching point 2

Round mark

Sifter

Loading gear (T)

Insert point 1

Shaft 1

Half round notch

Insert point 4

Phase-matching point 1

Rotation point 2

Shaft 1

Figure 4-43.

Shaft 4

Release point 3

Insert point 5

+ 56 hidden pages