SHARP VC-TA350, VC-TA351, VC-TA351W, VC-TA355, VC-TA356 Service Manual

...
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
SERVICE MANUAL
S70E1VC-TA350
VIDEO CASSETTE RECORDER
VC-TA350
VC-TA352W Only
VC-TA351 VC-TA351W VC-TA352W VC-TA355
MODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used.
CONTENTS
1. SPECIFICATIONS................................................................................................................. 3
3. FUNCTION OF MAJOR MECHANICAL PARTS................................................................... 7
4. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS.................. 9
5. ELECTRICAL ADJUSTMENT ............................................................................................. 28
6. MECHANISM OPERATION FLOWCHART AND TROUBLESHOOTING GUIDE .............. 31
8. BLOCK DIAGRAM............................................................................................................... 48
10. REPLACEMENT PARTS LIST ............................................................................................ 68
11. EXPLODED VIEW............................................................................................................... 75
12. PACKING OF THE SET ...................................................................................................... 79
VC-TA356
Page
SHARP CORPORATION
1
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
PRECAUTIONS IN PART REPLACEMENT
When servicing the unit with power on, be careful to the section marked white all over. This is the primary power circuit which is live.
When checking the soldering side in the tape travel mode, make sure first that the tape has been loaded and then turn over the PWB with due care to the primary power circuit. Make readjustment, if needed after replacement of part, with the mechanism and its PWB in position in the main frame.
(1) Start and end sensors: Q701 and Q702
Insert the sensor’s projection deep into the upper hole of the holder. Referring to the PWB, fix the sensors tight enough.
(2) Photocoupler: IC902
Refer to the symbol on the PWB and the anode marking of the part.
(3) Cam switches A and B: D708 and D709.
Adjust the notch of the part to the white marker of the symbol on the PWB. Do not allow any looseness.
(4) Take-up and supply sensors: D707 and D706.
Be careful not to confuse the setting direction of the parts in reference to the symbols on the PWB. Do not allow any looseness.
2
1. SPECIFICATIONS
Format: VHS PAL/MESECAM/NTSC standard
Video recording system: Rotary, slant azimuth two heads helical scan system
Video signal: PAL/MESECAM/NTSC colour or monochrome (System B/G, I, D/K) signals
Recording/playing time: 240 min max. with SHARP E-240 tape (PAL: SP mode)
Tape width: 12.7mm
Tape speed: 23.39 mm/s (PAL: SP mode)
Antenna: 75 ohm unbalanced
Receiving channel: VHF Channel 1A - S41, UHF Channel E21 - C57
RF converter output signal: UHF Channel E21 - E69 Adjustable preset to E60 (For A/M/B/W-version)
Power requirement: AC110 - 240V, 50/60Hz
Power consumption: Approx. 13W at 240V/50Hz
Operating temperature: 5°C to 40°C
Storage temperature: –20°C to 55°C
Weight: Approx. 2.8 kg
Dimensions: 360 mm (W) x 256 mm (D) x 92 mm (H)
Output: 1.0 Vp-p, 75 ohm
S/N ratio: 45 dB (PAL-SP)
Horizontal resolution: 250 lines (PAL-SP)
Output: Line -8 dBs/1k ohm
S/N ratio: 46 dB (SP mode)
Frequency responce: 80 Hz ~ 10 kHz (SP mode)
Accessories included: 75 ohm coaxial cable
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
480 min max. with SHARP E-240 tape (PAL: LP mode) (Only for VC-TA351/TA351W, TA352W, TA355, TA356) 160 min max. with SHARP T-160 tape (NTSC: SP mode) 480 min max. with SHARP T-160 tape (NTSC: EP mode) (Only for VC-TA351/TA351W, TA352W, TA355, TA356)
11.70 mm/s (PAL: LP mode)
33.35 mm/s (NTSC: SP mode)
16.67 mm/s (NTSC: LP mode) (Playback only)
11.12 mm/s (NTSC: EP mode)
UHF Channel E21 - E69 Adjustable preset to E39 (For S/K/L-version)
VIDEO
Input: 1.0 Vp-p, 75 ohm
AUDIO 0 dBs = 0.775 Vrms
Input: Line 1: -8 dBs/47k ohm
80Hz ~ 5 kHz (LP/EP mode) Operation manual
Remote control unit Battery
As part of our policy of continuous improvement, we reserve the right to alter design and specifications without notice.
Note: The antenna must correspond to the new standard DIN 45325
(IEC 169 - 2) for combined UHF/VHF antenna with 75 ohm connector.
3
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
2. DISASSEMBLY AND REASSEMBLY
2-1 DISASSEMBLY OF MAJOR BLOCKS
TOP CABINET : Remove 2 screws 1. FRONT PANEL : Remove 2 screws 3 and 7 clips 4. OPERATION : Remove 1 screw 6. PWB SHIELD ANGLE : Remove 1 screws 7 with shield angle. MECHANISM/ : Remove 1 screw 8, 2screws 0, MAIN PWB 2 screws q. Remove 1screw w
with antenna terminal cover. Remove 1 screw e with top cabinet fix angle.
ANTENNA TERMINAL COVER
MECHANISM/ MAIN PWB ASSEMBLY
TOP CABINET
3
12
1
SHIELD ANGLE
7
C
11
3
B
H/A SHIELD TOP
A
10
FRONT PANEL
A
8
TOP CABINET FIX ANGLE
13
C
B
MAIN FRAME
4
6
2
OPERATION PWB
4
2-2 DISASSEMBLING THE MECHANISM/MAIN PWB ASSEMBLY
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
1. When removing the mechanism from the main PWB, remove the antenna cover 1 screw 1, and remove the antenna cover. Remove the PWB bottom plate 1 screw 2. Remove the FFC cable (AA, AD, AH) 3 which con­necting the PWB and the mechanism. Take out vertically the mechanism so that it does not damage the adjacent parts.
4
CASSETTE HOUSING
2. Removing the mechanism and cassette housing. Remove 2 screws 4 fixing the cassette housing to the mechanism, and remove the cassette housing.
MECHANISM CHASSIS
1
3
VC-TA352W
MAIN PWB
2
5
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
2-3 CARES WHEN REASSEMBLING
INSTALLING THE CASSETTE HOUSING
When the cassette housing is installed on the mechanism, the initial setting is essential condition. There are two initial setting methods, namely electrical and mechanical.
1. Electrical initial setting
So as to perform initial setting of mechanism execute the Step 1 of Installation of cassette housing. After ascertain­ing the return to the initial setting position (*1) install the
Pulley feed gear
Screwdriver
Tilt mark (*1)
cassette housing. (Conditions: When mechanism and PWB have been installed)
2. Mechanical initial setting
Feed the pulley feed gear of loading motor with screw driver. After ascertaining the return to the initial set posi­tion (*1) install the cassette housing in the specified position. (This method is applied only for the mechanism.)
Casecon drive gear
Drive angle of cassette housing
INSTALLING THE MECHANISM ON PWB
Lower vertically the mechanism, paying attention to the mechanism edge, and install the mechanism with due care so that the parts are not damaged. So as to fix the mechanism to the main PWB install two housings. (Fit the antenna cover to one of them. For other, fix the vicinity of loading motor and solder joint side of main PWB.) Con­nect again the FFC cable (AA-MH, AD-ME, AH-MH) between the mechanism and the main PWB.
END SENSOR
REC TIP SW
PARTS WHICH NEED PARTICULAR CARE
When installing the mechanism chassis on the PWB unit, take care so as to prevent deformation due to contact of mechanism chassis with REC TIP SW.
AE CONNECTOR
AC CONNECTOR
START SENSOR
AL CONNECTOR
6
3. FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW)
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
1715
18
10
14
1
9
2
7
3
11
5
12
8
6
No. Function
1 Full erase head 2 Supply pole base ass’y 3 Tension arm ass’y 4 Idler wheel ass’y 5 Pinch drive lever ass’y 6 Supply reel disk 7 Supply main brake ass’y 8 Take-up main brake ass’y 9 Pinch drive cam
10 A/C Head ass’y
4
No. Function
11 Reverse guide lever ass’y 12 Casecon drive gear 13 Take-up reel disk 14 Pinch roller lever ass’y 15 Drum ass’y 16 Loading motor 17 Drum motor 18 Take-up pole base ass’y
13
16
7
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW)
21
22
19 20
12
23
25
24
No. Function
19 Slow brake lever 20 Master cam 21 Capstan D.D. motor 22 Reel belt
No. Function
23 Clutch lever 24 Limiter pulley ass'y 25 Shifter
8
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
4. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS
The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.
4-1 MECHANISM CONFIRMATION ADJUSTMENT JIG
So as to perform completely the mechanism adjustment prepare the following special jigs. So as to maintain the initial performance of the machine the maintenance and check are necessary. Utmost care must be taken so that the tape is not damaged. If adjustment needs any jig, be sure to use the required jig.
No. Jig ltem Part No. Code Configuration Remarks
This cassette torque meter is used for check-
1. Torque Cassette Meter JiGVHT-063 CZ
JiGTG0090 CM
2.
Torque Gauge
JiGTG1200 CN
3. Torque Gauge Head JiGTH0006 AW
ing and adjusting the torque of take-up for measuring tape back tension.
These Jigs are used for checking and adjusting the torque of take-up and supply reel disks.
4. Torque Driver JiGTD1200 CB
Master Plane Jig and Reel Disk Height
5. Adjusting Jig
JiGRH0002 BR JiGMP0001 BY JiGSG2000 BS
Tension Gauge
6.
JiGSG0300 BF
Pinch pressing force
7. JiGADP003 BK
measuring jig Reverse guide height
8.
adjusting box driver
JiGDRiVER11055
AR
9. Alignment Tape VROCPSV CK
Guide roller height
10. JiGDRiVERH-4 AP
adjustment drive
X value adjustment
11. JiGDRiVER-6 BM
gear type screw driver Reverse Guide Height
12. JiGRVGH-F18 BU
Adjusting Jig
When fixing any part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg)
These Jigs are used for checking and adjusting the reel disk height.
There are two gauges used for the tension measurements, 300 g and
2.0kg. This Jig is used with the tension
gauge. Rotary transformer clearance adjusting jig.
This Jig is used for height adjustment of the reverse guide (for reverse guide height ad­justment).
This tape is especially used for electrical fine adjustment.
Video Audio Track
625 Monoscope 6kHz 49µm
PAL Colour bar 1kHz 49µm
This screwdriver is used for adjusting the guide roller height.
For X value adjustment
This Jig is used for height adjustment of the reverse guide.
9
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MAINTENANCE CHECK ITEMS AND EXECUTION TIME
Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine.
Maintained
Parts
Guide roller ass’y Sup guide shaft Reverse guide Slant pole on pole base Full erase head A/C head
Upper and lower drum ass’y
Capstan D.D. motor Pinch roller
Reel belt
500 hrs.
1000 hrs.
1500 hrs.
2000 hrs.
Possible symptom
encountered
Lateral noises Head occasionally blocked
color and beating Small sound or sound
distortion Poor S/N ratio, no color
Poor flatness of the envelope with alignment tape
No tape running, uneven color
No tape running, tape slack
No tape running, tape slack, no fast forward/ rewind motion
Remarks
Abnormal rotation or significant vibration requires replacement.
Clean tape contact part with the specified cleaning liquid.
Clean tape contact area with the specified cleaning liquid.
Clean rubber and rubber contact area with the specified cleaning liquid.
Tension band ass’y Loading motor
Idler ass’y Limiter pulley Supply/take-up main brake levers
Screen swaying Cassette not loaded or
unloaded No tape running, tape
slack
Tape slack
NOTE : Part replacement. : Cleaning : Apply grease <Specified> Cleaning liquid Industrial ethyl alcohol
* This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found,
clean or replace parts.
Video head cleaning procedure
1. Apply one drop of cleaning liquid to the cleaning paper with the baby oiler.
2. Gently press the cleaning paper against the video head to fix your finger, and move the upper drum so that each head is passed to and from 5 times (do not move the cleaning paper).
3. Wipe with the dry cleaning paper.
Notes :
• Use the commercially available ethanol of Class 1 as cleaning liquid.
• Since the video head may be damaged, do not move up
Gently press the cleaning paper to fix with your finger, and rotate the upper drum to clean. Move to and from 5 times for each head. (Do not move the cleaning paper.)
Rotate the upper drum with one hand.
and down the cleaning paper.
• Whenever the video head is cleaned, replace the clean­ing paper.
• Do not apply this procedure for the parts other than the video head.
Parts Code Description Code
ZPAPRA56-001E Cleaning Paper AW
ZOiLR-02-24TE Babe Oiler (Spoit) AH
10
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REMOVING AND INSTALLING THE CASSETTE HOUSING
• Removal
1. In the cassette removing mode, remove the cassette.
2. Unplug the power cord.
3. Remove in the following numerical order. a) Remove two screws 1. b) Slide and pull up the cassette housing control.
1
Notes:
1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care.
2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated).
3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum.
4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum.
5. After installing the cassette housing control once per­form cassette loading operation.
TO RUN A TAPE WITHOUT THE CASSETTE HOUSING CONTROL ASSEMBLY
1. Remove the full-surface panel.
2. Short-circuit TP801.
3. Plug in the power cord.
4. Turn off the power switch.
(The pole bases move into U.L.position.)
5. Open the lid of a cassette tape by hand.
6. Hold the lid with two pieces of vinyl tape.
7. Set the cassette tape in the mechanism chassis.
8. Stabilize the cassette tape with a weight (500g) to
prevent floating.
9. Turn on the power switch.
10. Perform running test.
Figure 4-1.
• Reassembly
1. Before installing the cassette housing control, short­circuit TP801 provided at the center (when facing to the main PWB), press the eject button. The casecon drive gear turns and stops when the positioning mark ap­pears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below.
Casecon drive gear
Casecon drive angle gear
500g
Weight to prevent float (500g)
Mechanism chassis
Figure 4-3.
Note:
The weight should not be more than 500g. To take out the cassette tape.
1. Turn off the power switch.
2. Take out the cassette tape.
Figure 4-2.
2. Install in the reverse order of removal.
11
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REEL DISK REPLACEMENT AND HEIGHT CHECK
• Removal
1. Remove the cassette housing control assembly.
2. Pull the tension band out of the tension arm ass'y.
3. Remove the Supply/Take-up main brake ass'y.
4. Open the hook at the top of the reel disk, and remove the reel disk.
Note:
Take care so that the tension band ass'y and main brake ass'y (especially soft brake) are not deformed.
Tension arm ass'y
Supply main brake ass'y
Tension band ass'y
Supply reel disk
Take-up main brake ass'y
Take-up reel disk
4. Assemble the Supply main brake ass'y.
Notes:
1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere.
2. Do not damage the Supply main brake ass'y. Be careful so that grease does not adhere to the brake surface.
• Reassembly (Take-up reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to it.
2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft.
3. Check the reel disk height and reassemble the take-up main brake ass'y.
Note:
1. Take care so that the Take-up main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface.
2. After reassembly, check the video search rewind back tension (see page 15), and check the brake torque (see page 17).
• Height checking and adjustment Note:
1. Set the master plane with due care so that it does not contact the drum.
2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage.
Figure 4-4.
Note:
When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed.
Figure 4-5.
• Reassembly (Supply reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to it.
2. Match the phases of reel disk and reel relay gear, and set the new reel disk.
3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y.
Master plane
Reverse guide
Supply reel disk
Cassette lock release shaft
Take-up reel disk
Position pin
Figure 4-6.
Note:
• Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk.
12
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Note:
Whenever replacing the reel disk, perform the height check­ing and adjustment.
Master plane
10 ± 0.2mm
Reel disk
Reel disk
Reel disk height adjusting jig
Mechanism chassis
A
B
Figure 4-7.
CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN FAST FORWARD MODE
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.
2. Press the FF button.
3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode.
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction.
2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long­time measurement.
CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN REWIND MODE
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the supply reel disk.
2. Press the rewind button.
3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode.
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction.
2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
30mN·m (306gf·cm) or more
CCW
The gauge is held at its maximum value. (Red mark)
30mN·m (306gf·cm) or more
Idler ass'y
CW
The gauge is held at its maximum value. (Red mark)
Figure 4-8.
• Adjustment
1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, reel belt, and limiter pulley with cleaning liquid, and check again.
2. If the torque is less than the set value, replace the reel belt.
Supply reel disk
Idler ass'y
Figure 4-9.
• Adjustment
1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque.
2. If the winding-up torque is still out of range, replace the drive belt.
13
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long­time measurement.
CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN RECORD/PLAYBACK MODE
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Turn off the power switch.
• Open the cassette torque meter lid, and fix it with tape.
• Load the cassette torque meter into the unit.
• Put the weight (500g) on the cassette torque meter.
• Turn on the power switch.
• Press the REC button, and set SP picture record mode.
Set value SP7.8 ± 3mNm (80 ± 30 gfcm)
CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN VIDEO SEARCH REWIND MODE
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
Press the playback button and rewind button to set the video search rewinding mode.
• Checking
Place the torque gauge on the supply reel disk, and turn it counterclockwise very slowly (one rotation every 1 to 2 seconds) and check that the torque is within the set value
14.0 ± 3.9mNm. (144 ± 40gfcm)
Torque gauge
CCW
500g
Cassette torque meter
Figure 4-10.
• Checking
1. Make sure that value is within the setting 7.8 ± 3 mN·m (80 ± 30 gf·cm).
2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting.
3. Set the SP record mode and make sure that the winding­up torque is within setting.
• Adjustment
If the playback winding-up torque is not within the setting, replace the limiter pulley assembly.
Note:
When the torque cassette is set, put a weight (500g) to prevent rise. When the cassette torque meter is taken out. Turn off the power switch.
Supply reel disk
Figure 4-11.
Note:
Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible.
• Adjustment
If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly.
Note:
The winding-up torque fluctuates due to variation of rota­tion torque of supply reel disk. Read the center value of fluctuation as setting.
14
CHECKING THE VIDEO SEARCH REWIND BACK TENSION
• Remove the cassette housing control assembly.
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Checking
1. After pressing the play button, press the rewind button, and set the video search rewind mode.
2. Place the torque gauge on the take-up reel disk, and turn it counterclockwise very slowly (one rotation every 2 to 3 seconds) and check that the torque is within the set value 3.4±1.5mNm (35±15gfcm).
Torque gauge
CCW
Take-up reel disk
Pinch roller
Capstan shaft
Tension gauge adapter
Tension gauge
8.8 ~ 11.8 N (900 - 1,200gf)
Figure 4-13.
1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage.
2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction.
3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft.
4. Make sure that the measured value is within setting 8.8 to 11.8 N (900 to 1,200gf).
Figure 4-12.
Notes:
Set the torque gauge securely on the take-up reel disk. If it is not secure, the measurement will be incorrect.
CHECKING THE PINCH ROLLER PRESSURE
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Checking
Press the play button to set the playback mode.
CHECKING AND ADJUSTMENT OF TENSION POLE POSITION
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
1. Turn off the power switch.
2. Open the cassette tape (E-180), and fix with tape.
3. Set the cassette tape in loading state.
4. Put the weight (500g) on the cassette tape.
5. Turn on the power switch.
6. Make the adjustment with the beginning of a E-180 tape.
(E-180)
500g
Weight to prevent float (500g)
Figure 4-14.
• Checking
1. Set a cassette tape, push the REC button to place the
unit in the SP record mode. Now check the tension pole position.
15
VC-TA350/TA351/351W
2.3 ± 0.25
VC-TA352W/TA355/TA356
2. Visually check to see if the right edge of the tension pole is within the 2.3 ± 0.25 from the right edge of the Sup guide shaft.
Sup guide shaft
Tension pole
Make the adjustment with the beginning of a E-180 tape.
Figure 4-15.
At left side from the center line
Tension pole adjuster adjusting range
Tension pole adjuster
90°
90°
Figure 4-18.
Adjust so that the delta mark of tension pole adjuster is within 90° range (left, right).
CHECKING AND ADJUSTMENT OF RECORD/ PLAYBACK BACK TENSION
• Remove the cassette housing control assembly.
2.3 ± 0.25
Figure 4-16.
Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise.
At right side from the center line
2.3 ± 0.25
Figure 4-17.
Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
1. Turn off the power switch.
2. Open the torque cassette meter and fix with tape.
3. Set the cassette tape in loading state.
4. Put the weight (500g) on the cassette torque meter.
5. Turn on the power switch.
500g
Weight to prevent float (500g)
Cassette torque meter
Figure 4-19.
• Checking
1. Push the REC button to place the unit in the SP record mode.
2. At this time ascertain that the back tension is within the setting (36.5 to 52g·cm) by seeing the indication of torque cassette meter.
16
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
• Adjustment
1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A.
2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
A
B
Tension arm
Tension spring
Figure 4-20.
CHECKING THE BRAKE TORQUE
• Checking the brake torque at the supply side
Torque gauge
CCW
CW
• Checking the brake torque at the take-up side
Torque gauge
CW
Take-up reel disk
CCW: 4.9~13.7mNm (50~140gfcm) CW: 3.9~10.8mNm (40~110gf cm)
CCW
Figure 4-22.
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
Supply reel disk
CCW: 2.9~9.8mNm (30~100gfcm) CW: 4.9~13.7mNm (50~140gfcm)
Figure 4-21.
• Remove the cassette housing control assembly.
• After short-circuiting TP801 provided at the center (facing to the main PWB), plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the supply reel disk.
2. Switch from the FF mode to the STOP mode.
3. Disconnect the power cord.
• Checking
Turn the torque gauge at a rate of about one turn/2 sec in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 4.9 to 13.7mN·m (50 to 140gf·cm); CCW direction: 2.9 to 9.8mN·m (30 to 100gf·cm).
• Setting
1. Switch from the FF mode to the STOP mode.
2. Disconnect the power cord.
3. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.
• Checking
1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 4.9 to 13.7mN·m (50 to 140gf·cm), CW direc­tion: 3.9 to 10.8 mN·m (40 to 110gf·cm).
2. Adjustment of the brake torque at the supply side and the take-up side
• Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque.
• If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring.
17
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REPLACEMENT OF A/C (Audio/Control) HEAD
1. Remove the cassette housing control assembly.
2. In unloading state unplug the power cord.
• Removal
1. Remove the screws 123, Azimuth screw, Tilt screw.
2. Unsolder the PWB fitted to the A/C head.
Notes:
1. When replacing, never touch the head. If you touched, clean with the cleaning liquid.
2. When removing the screw 3, take care so that the spring may out.
Tilt screw
3
Azimuth screw
Height screw
Spring
1
3. Align the left end of gear of A/C head plate with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head plate. Tentative tightening torque must be 0.15 to 0.20 N·m (1.5 to 2.0kgf·cm).
1
3
Height screw
Left end of A/C head plate gear
2
Punched line mark on chassis
Figure 4-25.
Note:
1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken.
2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in Page 20, 21.)
2
Figure 4-23.
• Replacement
1. Solder the removed PWB to the new head assembly.
2. Adjust the height from the A/C head plate (lower surface) to the A/C head base to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw section and hight screw section) (See the figure below.)
Solder
New A/C head ass'y
Never touch the head
A/C head base
A/C head PWB
Figure 4-24.
10.8mm10.8mm
18
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
A/C HEAD HEIGHT ROUGH ADJUSTMENT
• Setting
Height screw
Weight to prevent float (500g)
1. Set the cassette tape in the unit.
2. Press the PLAY button to put the unit in the playback mode.
3. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below.
Azimuth screw
Tilt screw
Cassette tape
500g
Mechanism chassis
Figure 4-26.
A/C head
HEIGHT ADJUSTMENT OF REVERSE GUIDE
1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38 mm, using the reverse guide height adjustment jig, in tape loading state. (Refer to Figure 4-28 (a) (b).)
Reverse guide Reverse guide height adjusting jig
Mechanism chassis
(a)
Figure 4-28.
2. Rotate counterclockwise the reverse guide height ad­justment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER11055)).
CCW
Reverse guide height adjusting jig
13.38mm
(b)
Box driver
Height adjusting nut
Tape
0.3mm
Figure 4-27.
• Adjustment
Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape.
Figure 4-29.
3. Set the tape, and check for tape crease near the reverse
guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 4-
30.)
500g
Weight to prevent float (500g)
A
Mechanism chassis
Reverse guide
Capstan motor shaft
Fixing guide
An example of crease near the reverse guide
* Check for crease from the A direction.
Figure 4-30.
19
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
ADJUSTMENT OF TAPE DRIVE TRAIN
1. Tape run rough adjustment
1 Remove the cassette housing control assembly. 2 After shortcircuiting TP801 provided at the center
(facing to the main PWB), plug in the power cord.
3 Check and adjust the position of the tension pole.
(See page 15.)
4 Check and adjust the video search rewind back
tension. (See page 15.)
5 Connect the oscilloscope to the test point for PB
CHROMA envelope output (TP201). Set the syn­chronism of the oscilloscope to EXT. The PB CHROMA signal is to be triggered by the head switching pulse (TP202).
6 Set the alignment tape (VROCPSV) to play. (Put a
500g weight on the cassette tape to prevent lift of cassette tape.)
Guide roller
Cassette Tape
500g
Weight of 500g
Figure 4-31.
7 Press the tracking button (+), (–) and change the
envelope waveform from max to min and from min to max. At this time make sure that the envelope waveform changes nearly parallel.
8 Unless the envelope waveform changes nearly par-
allel, adjust the height of supply side and take-up side guide roller so that the envelope waveform changes nearly parallel. (For envelop adjustment procedure refer to Figure 4-35.)
9 Turn the tilt screw to remove the tape crease at the
fixing guide flange.
Playback the tape and check for tape crease at the
fixing guide flange.
(1)If there is no tape crease
Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears.
(2)If there is tape crease
Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange.
Notes:
1. Previously set the tracking control in the center position, and adjust the envelop waveform to maximum with X value adjustment nut. Thereby the tape run rough ad­justment is facilitated.
2. Especially the outlet side envelope waveform must have higher flatness.
Figure 4-32.
2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the
method stated in "Page 18 Replacement 3".
2 Connect the oscilloscope to the audio output termi-
nal.
3 Using the alignment tape in which 1 kHz linear audio
signal has been recorded, adjust the height screw so as to get max audio output.
4 Using the alignment tape in which 6 kHz linear audio
signal has been recorded, adjust the azimuth screw so as to get max audio output.
5 Repeat the above adjustment steps 3 and 4 a
couple of times. Finally take the step 4 again.
For X value adjustment Adjust the X value, turning the gear­type screwdriver.
Figure 4-33.
3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA envelope
output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switch­ing pulse).
2 Rough adjustment of X value
Tentatively fix A/C head arm screws 1 and 2 by the method described in Page 18 "Replacement 3". Playback the alignment tape (VROCPSV) and shortcircuit TP802. As a result the auto-tracking is automatically cancelled, so that the X value adjust­ment mode is set. Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Fig­ure 4-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: When the A/ C head is adjusted, adjust so that the maximum envelop waveform is obtained nearest the position of initial setting made in Page 18.)
20
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
3 Next, press the tracking button (+), (–) and change
the envelope waveform from max to min and from min to max. At this time adjust the height of supply and take-up side guide roller with the adjustment driver (JiGDRiVERH-4) so that the envelope wave­form changes nearly parallel.
4 If the tape is lifted or sunk from the helical lead
surface, the PB CHROMA envelope waveform ap­pears as shown in Figure 4-35.
5 Press the tracking button (+), (–) and make sure that
the envelope waveform changes nearly parallel.
6 Finally check tape crease near the reverse guide. If
tape crease is found, remove it as stated in Page 19 "HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3.
Supply side
Take-up side Supply side Take-up side
PB CHROMA Envelope
CH-1 CH-2
Head switching pulse
Figure 4-34.
4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the
method described in Page 18 "Replacement 3".
2 Playback the alignment tape and shortcircuit TP802.
As a result the auto-tracking is automatically can­celled, so that the X value adjustment mode is set.
3 Move the A/C head with the X value adjustment gear
driver by the method shown in Figure 4-33, and
When the tape is below the helical lead.When the tape is above the helical lead.
Adjustment
Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Figure 4-35.
adjust the A/C head so as to get the maximum envelope waveform. (Note: At this time adjust so as to get the maximum envelope waveform nearest the A/C head position which has been set in case of X value rough adjustment as stated in Page 20, 3- 2.)
4 Tighten finally the screws 1 and 2. Be sure to
tighten at first the screw 1 and then the screw 2. Final tightening torque is 0.6N·m (If the screw 2 is tightened first, the X value may deviate.)
5 Adjust the playback switching point (Refer to the
electric adjustment method.)
6 Playback the self-picture-recorded tape, and check
the flatness of envelope waveform and sound.
Notes:
When the A/C head X value adjustment is performed, be
Supply side guide roller rotated in counterclock­wise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the envelope.
Take-up side guide roller rotated in counterclock­wise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the envelope.
sure to perform at first X value rough adjustment (refer to Page 20, 3-2).
2
1
Figure 4-36.
21
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REPLACEMENT OF THE CAPSTAN D.D. (DIRECT DRIVE) MOTOR
• Remove the mechanism from the main PWB (refer to Page 6 item 1. When removing the mechanism from the main PWB").
• Removal (Follow the order of indicated numbers.)
1. Remove the reel belt 1.
2. Remove the slow brake lever 2.
3. Remove the three screws 3.
3
Capstan D.D. motor
Capstan D.D. motor
control PWB
REPLACEMENT OF DRUM D.D. MOTOR
1. Set the ejection mode.
2. Withdraw the main power plug from the socket.
• Removal (Perform in numerical order.)
1. Disconnect the FFC cable 1.
2. Unscrew the D.D. stator assembly fixing screws 2.
3. Take out the D.D. stator assembly 3.
4. Unscrew the D.D. rotor assembly fixing screws 4.
5. Take out the D.D. rotor assembly 5.
Notes:
1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it.
2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.)
3. Be careful not to damage the upper drum or the video head.
4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y.
5. After installation adjust the playback switching point for adjustment of servo circuit.
1
Reel belt
2
Slow Brake lever
Figure 4-37-1.
• Reassembly
1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mecha­nism chassis, and then install with the three screws.
2. Install the slow brake lever.
3. Install the reel belt.
Notes:
1. Before installing the capstan D.D. motor, confirm whether an acetate tape (ZTAPEN120020E)is drawn on the back of mechanism chassis.
Stick an acetate tape on the projection part of the chassis.
Capstan Motor installation position.
MechanismChassis from the back.
Figure 4-37-2.
2
D.D. stator ass'y
3
4
5
4
D.D. rotor ass'y
1
FFC
Upper drum
Figure 4-38.
2. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the move­ment.
3. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in Page 21 Replacement
2. If crease is found, adjust as stated in Page 20 "HEIGHT ADJUSTMENT OF REVERSE GUIDE".
22
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REPLACING THE UPPER AND LOWER DRUM ASSEMBLY
• Replacement (Perform in the numerical order) 1 Remove the motor as stated in Page 22 D.D. motor
replacement.
2 Remove the drum earth brush ass’y 2. 3 Remove the drum base 3 from the upper and lower
drum assembly 1.
[Cares when replacing the drum]
1. Be careful so that the drum earth brush is not lost.
2. Do not touch directly the drum surface.
3. Fit gently the screwdriver to the screws.
4. Since the drum assembly is an extremely precise as­sembly, it must be handled with utmost care.
5. Make sure that the drum surface is free from dust, dirt and foreign substances.
6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment.
• Playback switching point adjustment
• X-position adjustment and check
• Standard and x-3 slow tracking adjustment
7. After replacing the drum clean the drum.
ASSEMBLING OF PHASE MATCHING MECHANISM COMPONENTS
• Assemble the phase matching mechanism compo­nents in the following order.
1. Assemble the pinch roller assembly and pinch drive cam.
2. Mounting the shifter (on the back of the mechanism chassis).
3. Mounting the master cam (on the back of the mecha­nism chassis).
4. Assemble the connection gear, slow brake and loading motor parts.
• Pinch drive cam and pinch roller assembling
method.
(Place the following parts in position in numerical order.)
(1)Reverse drive lever 1 (2)Reverse guide spring 2 (3)Reverse guide lever ass’y 3 (4)Reverse guide height adjusting nut 4 (5)Pinch drive cam 5 (6)Pinch roller ass’y 6 (7)Open lever 7
7
2
1
3
Figure 4-40.
4
3
2
6
1
5
Figure 4-39.
23
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
1Insert Reverse Guide Lever Ass’y
Insert reverse guide lever ass'y
2 Insert pinch drive cam
Turn the reverse guide lever assembly counterclockwise to the stopper.
Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis.
Pinch drive lever ass'y
Figure 4-41-1.
2Insert Pinch Roller/Pinch Double Action Lever Ass’y.
Pinch Roller Double Action Lever Ass'y
Phase Matching Point 2
Align here.
Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly.
3Insert Open Lever.
Open lever
Figure 4-41-2.
Figure 4-41-3.
24
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
INSTALLING THE SHIFTER
Capstan D.D. motor
Reel pulley
(Bottom side of mechanism chassis)
Figure 4-42.
Insert point 3
Drum
1. Make sure that the loading gear is at the PHASE­MATCHING point 1 as shown below.
2. Install, paying attention to insert point 5 and release point 3.
3. For the phase matching at the insert point 1, see the PHASE-MATCHING point 2 as shown below.
4. Finally fix the inserts 1 and 4.
Phase-Matching point 2
Loading gear (T)
Round mark
Sifter
Half round notch
Insert point 1
Shaft 1
Insert point 2
Rotation point 2
Shaft 1
Insert point 4
Shaft 2
Insert point 5
Phase-matching point 1
Shaft 1
Release point 3
Figure 4-43.
25
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
INSTALLING THE MASTER CAM (AT REAR SIDE OF MECHANISM CHASSIS)
1. Make sure beforehand that the shifter is at the point as shown below.
2. Place the master cam in the position as shown below.
E ring (XRESJ30-06000)
Master cam
Fully turn clockwise
Fully turn counterclockwise
Face the wide tooth side ward
Figure 4-44-1.
REPLACEMENT OF LOADING MOTOR
• Removal
Apply grease
Apply grease
No grease
Note:
See the figure below for the phase matching between the master cam and the casecon drive gear.
3. Finally fix with the E ring.
Master cam
Casecon drive gear
Half-round notch
Round mark
When installing the master cam, align the casecon drive gear round mark with the half-round notch of master cam.
Figure 4-44-2.
Figure 4-45.
• Replacement
Remove the loading motor, and install the replacement loading motor as shown below.
+0.2
10.2 mm
–0.2
Figure 4-46.
The loading motor pressing-in must be less than 147 N (15 kgf). Adjust the distance between motor and pulley to 10.2
+0.2
mm).
–0.2
26
ASSEMBLY OF CASSETTE HOUSING
1. Drive Gear and R Drive angle ass’y
Apply grease
2. Synchro Gear, Drive Gear L and Drive Gear R
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MSPRT0381GEFJ
Apply grease
Apply grease
Figure 4-47.
Top surface should be free from scratches or soil.
Drive angle
LANGF9592GEFW
Drive gear R
Frame
Figure 4-48.
27
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
5. ELECTRICAL ADJUSTMENT
Notes:
• Before the adjustment:
Electrical adjustments discussed here are often required after replacement of electronic components and mechani­cal parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments, otherwise adjustments can not be completed.
• Instruments required:
Colour TV monitor Dual-trace oscilloscope
Alignment tape (VROCPSV), (VROATSV)
Blank video cassette tape DC voltmeter Screwdriver for adjustment
Servicing precautions When the IC710 (E2PROM) has been replaced, make the following reprogramming. Depending on models, the IC710 (E2PROM) has been factory-adjusted for it’s memory function. It’s therefore necessary to reprogram the memory function for the model in question. Note that the servo circuit requires readjustments for the head switching point, slow and still modes.
• Location of controls and test points
Figure 5-1.
28
VC-TA350/TA351/351W
j
VC-TA352W/TA355/TA356
SERVO CIRCUIT ADJUSTMENT
ADJUSTMENT OF HEAD SWITCHING POINT
Measuring instrument
Mode Cassette Test point Pin(2) of P201 (H.SW.P.) to CH-1,
Specification 6.5 ± 0.5H (lines)
1. Remove the front panel and play the alignment tape. (VROCPSV)
2. Get TP801 short circuited or press "TEST" key (47H) at universal remote control to call the Test Mode. (Digitron will blinking as tracking goes to center)
3. Press "PLAY". Auto PG Mode will be ON and playback mark " > " blinking.
4. Press "STOP". " > " blinking stops and auto adjustment finished.
5. Check that V-Sync is 6.5 ± 0.5H and the waveform is as shown in Figure 5-2.
Note:
For manual PG adjustment, press FF or REW at the Test Mode to set the tracking in center.
CH-2 Video signal
CH-1 HEAD SWITCHING PULSE
TRIG INT CH-1 H: 50u sec/d
Dual-trace oscilloscope Colour TV monitor
Playback Alignment tape (VROCPSV)
VIDEO OUT jack to CH-2 (CH-1 trigger slope switch at (+), Internal trigger at CH-1 side.)
6.5 ± 0.5H
V: 2V/djv
v
Figure 5-2.
ADJUSTMENT OF PAL SYSTEM SP/LP SLOW TRACKING PRESET
Measuring instrument
Mode Cassette
Control Tracking control buttons (]) or ([) Specification Minimized noise on
1. Have the unit to receive a good TV broadcast or feed a video signal to the VIDEO IN jack. (See note 2 below)
2. Set the tape speed in SP mode by using the remote control and record the signal on tape.
3. Rewind and play the tape where signal was recorded in above step.
4. Press the SLOW button on the remote control, and playback the recorded portion in the slow mode.
5. Make for a moment short-cirucuit TP801. Be sure that all the fluorescent display tubes light up into the TEST mode.
6. Look at the monitor screen and adjust the (]) or ([) TRACKING buttons so that the there is noise disap­pears from the screen.
7. Press the STOP button to return to normal mode.
8. Play the tape a few seconds then press the SLOW button again and make sure there is no noise in the screen.(For the LP mode put adjustment at the same adjustmet way as SP mode.)
Notes:
1 Self-recorded tape means a cassette whose program
was recorded by the unit being adjusted.
2 The TV program will not be recoded if RCA or 21pin
plugs are pluged in the AUDIO/VIDEO input terminals.
3 The tracking control is enabled with the (])/([)
button.
Colour TV monitor
Playback Self-recorded tape
(SP/LP mode)(See Note below)
monitor screen
29
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
ADJUSTMENT OF PAL SYSTEM FV (False Vertical Sync) OF STILL PICTURE
Measuring instrument
Mode Cassette
Control Tracking control buttons (]) or ([) Specification No vertical jitter of picture
1. Play a cassette which was recorded by the unit in SP mode.
2. Press the PAUSE/STILL button to freeze the picture.
3. Look at the monitor screen and adjust (]) or ([) TRACKING buttons so that the vertical jitter of the picture to be minimized.
4. Play and freeze the self-recorded tape in SP mode and make sure vertical jitter of the picture is not noticeable.(For the LP mode put adjustment at the same adjustment way as SP mode.)
Note:
1 Self-recorded tape is a cassette whose program was
recorded by the unit being adjusted.
2 The tracking control is enabled with the (])/([)
button.
Colour TV monitor
Playback still Self-recorded tape (SP mode)
(See Note below 1)
TRACKING buttons so that the there is no noise disap­pears from the screen.
7. Press the STOP button to return to normal mode.
8. Play the tape a few seconds then press the SLOW button again and make sure there is no noise in the screen.(For the E P mode put adjustment at the same adjustmet way as SP mode.)
Notes:
1 Self-recorded tape means a cassette whose program
was recorded by the unit being adjusted.
2 The TV program will not be recoded if RCA or 21pin
plugs are pluged in the AUDIO/VIDEO input terminals.
3 The tracking control is enabled with the (])/([)
button.
ADJUSTMENT OF NTSC SYSTEM FV (False Vertical Sync) OF STILL PICTURE
Measuring instrument
Mode Cassette
Colour TV monitor
Playback still Self-recorded tape (SP mode)
(See Note below 1)
ADJUSTMENT OF NTSC SYSTEM SP/EP SLOW TRACKING PRESET
Measuring instrument
Mode Cassette
Control Tracking control buttons (]) or ([) Specification Minimized noise on
1. Have the unit to receive a good TV broadcast or feed a video signal to the VIDEO IN jack. (See note 2 below)
2. Set the tape speed in SP mode by using the remote control and record the signal on tape.
3. Rewind and play the tape where signal was recorded in above step.
4. Press the SLOW button on the remote control, and playback the recorded portion in the slow mode.
5. Make for a moment short-ciucuit TP801. Be sure that all the fluorescent display tubes light up into the TEST mode.
6. Look at the monitor screen and adjust the (]) or ([)
Colour TV monitor
Playback Self-recorded tape
(SP/EP mode)(See Note below)
monitor screen
Control Tracking control buttons (]) or ([) Specification
1. Play a cassette which was recorded by the unit in SP mode.
2. Press the PAUSE/STILL button to freeze the picture.
3. Look at the monitor screen and adjust (]) or ([) TRACKING buttons so that the vertical jitter of the picture to be minimized.
4. Play and freeze the self-recorded tape in SP mode and make sure vertical jitter of the picture is not noticeable.(For the EP mode put adjustment at the same adjustment way as SP mode.)
Note:
1 Self-recorded tape is a cassette whose program was
recorded by the unit being adjusted.
2 The tracking control is enabled with the (])/([)
button.
No vertical jitter of picture
30
VC-TA350/TA351/351W
1
0
1
1
1
10
1
1
1
1
1
0
1
0
0
0
1
0
1
0
0
0
1
0
0
0
0
0
1
0
0
0
1
0
1
0
0
0
1
0
S sensor
Open
Close
Mode detection inside
sensor A
111000000
Mode detection outside
sensor B
011110110
CS/EJ
ULD
PU1
PU2
VSRPBSLOWFFSTOP
Cam graph E
25
20
15
10
5
0
60 120 180 240 300 360
G mechanical timing
Mode check
Cam mark
Mode detection outside
(D709 SW B)
Mode detection inside
(D708 SW A)
0 19.812 81 179 233200 265 282 316 334
10.354 12.812
CA/END
CS/EJ
UL
PU1
PU2
VSR
PB SLOW
FF
STOP
Mode detection outside
Mode detection inside
S sensor
EJ UL PU PU2 VSR PB SLW FF STP
011
011
000
001
0
0
1 or 0
Loading motor turns in reverse
direction and master cam
counterclockwise.
CASSETTE INSERTION STOP
Cassette
inserting
Full-
loading
YES
YES
YES
NO
NO
NO
Unloading
Loading motor starts in normal
direction and master cam counter
clockwise.
Does mechanism position sw.
come off within 2.5 sec.?
Are start/end sensors at low level
before cassette insertion ?
Insert cassette.
Double action rack slides.
Drum motor starts.
Tape loading.
Pinch roller comes into contact.
Cam switch is at PB position.
Loading motor stop.
Is drum FG pulse outputted ?
End
End
Cassette is ejected and loading
motor stops.
Start sensor close.
(Cassette is judged
caught halfway.)
(Cassette LED or some other part
is judged defective.)
VC-TA352W/TA355/TA356
MECHANISM OPERATION FLOWCHART
6. MECHANISM OPERA TION FLOWCHART AND TROUBLESHOOTING GUIDE
31
VC-TA350/TA351/351W
STOP REC/PLAY
PLAY STILL
PLAY VSR
VSR PLAY
Capstan motor turns
counterclockwise.
Is take-up reel sensor signal
outputted ?
End
Press REC/PLAY key.
Picture appears.
Unloading
Set capstan motor to search
speed.
End
Press FF key.
PLAY VSF
REC/PLAY STOP
Capstan motor turns in
reverse direction.
Loading motor turns in
counterclockwise direction
and master cam clockwise.
Slow brake comes into
contact with capstan motor.
Slow brake
pressing
Cam switch is at STILL
position.
End
Capstan motor stops.
Press STOP key.
Loading motor stops.
End
Stop capstan motor.
NO
YES
Press STILL key.
Pinch
roller
releasing
Idler
swinging
Pinch
roller
pressing
Loading motor turns
clockwise and master
cam counterclockwise.
Turn capstan motor in
reverse direction.
Turn loading motor
counterclockwise.
Cam switch is at VSR
position.
Set capstan motor to search
speed.
Is take-up reel sensor signal
outputted ?
Press REW key.
Release pinch roller.
Cam switch is at PU2 position.
Cam switch is at PU1 position.
Stop loading motor.
Press pinch roller.
Loading motor turns clockwise.
Release the supply auxiliary
brake.
Stop loading motor.
End
Unloading
Cam switch is at PB position.
End
Press PLAY Key.
Loading motor turns counter-
clockwise and master cam
clockwise.
Capstan motor turns
counterclockwise. PB speed.
NO
YES
VC-TA352W/TA355/TA356
32
VC-TA350/TA351/351W
STOP FF/REW
STOP CASSETTE EJECT
FF/REW STOP
NO
NO
FF/REW
operation
Brake
function
Turn capstan motor in
normal or reverse direction,
after the remaining tape has
been detected.
Loading motor turns counter-
clockwise.
Cam switcn is at Stop
position.
End
Press STOP key.
Press FF/REW key.
Stop capstan motor.
Loading motor stops.
End
Loading motor turns in clockwise and master cam
counterclockwise.
4 supply reel pulses
outputted ?
Does the take-up
reel pulse output
two edges?
Capstan motor turns
clockwise.
Loading motor turns
clockwise.
Cam switch is at
Eject position.
Loading motor
stops.
Capstan motor
stops.
Press EJECT key.
Tape
unloading
Cassette
eject
End
Capstan motor turns
clockwise.
Capstan motor turns
counterclockwise in about
2 seconds.
Stop loading motor.
Capstan motor turns in reverse direction.
Cam switch is at UL position.
YES
YES
VC-TA352W/TA355/TA356
33
VC-TA350/TA351/351W
MECHANISM TROUBLESHOOTING
1. FF/REW FAILURE (NO TAPE WINDING)
Press FF key.
NO
NO
NO
NO NO NO
NO
NO
YES
YES
YES
YES
YES
YES
YES YES
Is master cam at
FF position ?
Does loading
motor operate?
Modes changing
smoothly through
cam switch ?
Loading motor
control system
in trouble.
Are Vco 23V and
Vcc 5V applied ?
Replace the
capstan motor.
Replace the idler
ass’y.
Replace the reel
sensor.
Is voltage applied
to loading motor ?
Loading motor is
damaged. Replace
it.
Voltage supply
system in trouble.
Mode sensor
system in trouble
or master cam
malpositioned.
Voltage supply
system in trouble.
Does capstan
motor turn in FF (or
REW) direction ?
Are idler wheel
ass’y and reel disk
in mesh ?
Is the pulse
outputted from reel
sensor ?
The cassette tape
is presumably
damaged.
2. REC/PLAY FAILURE (MODE RELEASE)
NO
NO
NO
NO NO NO
NO
YES
YES
YES
YES
YES
YES
YES YES
Is the master cam
at PB position ?
Does loading
motor operate ?
Modes changing
smoothly through
cam switch ?
Loading motor
control system
in trouble.
Are Vco 23V and
Vcc 5V applied ?
Replace the
capstan motor.
Replace the idler
ass’y.
Replace the reel
sensor.
Is voltage applied
to loading motor ?
Loading motor is
damaged. Replace
it.
Voltage supply
system in trouble.
Voltage supply
system in trouble.
Does capstan
motor turn ?
Are idler wheel
ass'y and reel disk
in mesh ?
Is the pulse
outputted from reel
sensor ?
Check main PWB.
VC-TA352W/TA355/TA356
34
VC-TA350/TA351/351W
Replace loading motor block.
3. WINDING FAILURE AT VSR 4. UNUSUAL SOUND IN EACH MODE
Is Playback
function normal ?
Master cam
shifting to VSR
position ?
Go to 2. REC/
PLAY FAILURE
routine.
Replace idler
gear ass’y.
Replace limiter
pulley ass’y.
Replace reel
sensor.
Go to 2. REC/
PLAY FAILURE
routine.
Are idler wheel
ass’y and supply
reel disk in mesh ?
Is supply reel disk
winding torque
normal ?
Is pulse outputted
from reel sensor?
Check main PWB.
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
YES
YES
NO
NO
YES
Press REW key.
4-i) Unusual sound in cassette
insertion and ejection mode
Is unusal sound heard during
cassette coutrol running ?
Unusual sound heard with pinch
roller lever going up or down ?
Is unusual sound heard during
loading/unloading ?
Check pinch roller drive cam, pinch roller
drive lever and reverse guide for their actions.
Replace damaged one with new one.
Replace cassette control ass’y.
VC-TA352W/TA355/TA356
35
VC-TA350/TA351/351W
YES
YES
NO
NO
NO
NO
YES
YES
Replace capstan motor.
4-ii) Unusual sound in FF/REW mode
Is reel disk height as specified ?
Thrust gap found at reel disk ?
Drive system out of contact with any
part on main PWB ?
Turn capstan motor by hand.
Unusual sound heard ?
Check drive system’s gears for
damage. Replace damaged gear
with new one.
• Reel disk
• Limiter pulley ass’y
• Idler wheel ass’y
Check reel disk and main chassis.
And replace defective parts.
Adjust reel disk height.
Rearrange the parts on main PWB.
VC-TA352W/TA355/TA356
36
VC-TA350/TA351/351W
FLOW CHART NO.1 POWER TROUBLESHOOTING(1)
No power
Unplug the AC power cord.
Replug it a few minutes later.
See FLOW CHART NO.2 POWER
TROUBLESHOOTING(2)
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
Is the fuse good?
Replace fuse.
Is AT 5V voltage line normal?
Check primary circuit.
Are AT 42V, AT 23V, AT 12.6V, AT -25V
and filament voltage lines normal?
Check each rectifier circuits and
short-circuit of secondary circuit.
Is "H" level applied at pin(1) of
IC701?
Check peripheral circuits of Q706
and P-FAIL (L) signal line etc.
Check system control circuit(IC701).
FLOW CHART NO.2 POWER TROUBLESHOOTING(2)
In case of Fuse(F901) blown out.
Replace F901, Q901 and
R904, check D901, D902, D903 and
D904. Replace where necessary.
Check short-circuit or leakage of
D921, D922, D923, D924, D925,
D926 and secondary circuit.
FLOW CHART NO.3 POWER TROUBLESHOOTING(3)
In case of abnormal noise(sound)
Check D921, D922, D923, D924,
D925 and D926.
The Check D921, D922, D923,
D924, D925 and D926. Replace
where necessary.
NO
FLOW CHART NO.4 POWER TROUBLESHOOTING(4)
No power is turned on
Does power control (H) signal at pin
(4) of IC701 change from "L" to "H"
level?
Check IC701.
YES
YES
YES
NO
NO
NO
Does the base of Q951 change from
about 5.0V to 4.5V?
Check IC701 and all the way up
through to Q951.
Is voltage of 5V sent out from
collector of Q951.
Check peripheral circuit of Q951
and PC 5V line.
Check peripheral circuit for poor
soldering.
FLOW CHART NO.5 POWER TROUBLESHOOTING(5)
No power is turned on from STANDBY mode.
Is AT 5V voltage line normal?
Check rectifier circuit of AT 5V and
short-circuit of secondary circuit.
YES
YES
YES
YES
NO
NO
NO
NO
NO
Does STBY CTL signal at pin(94) of
IC701 change from "L" to "H" level?
Check the operation of IC701.
Does the filament STBY SW. circuit
Q947 is turned on?
Check peripheral circuit of Q947,
Q948, Q949, D940.
Does the STBY -25V SW. circuit Q944 is
turned on?
Check peripheral circuit of Q944.
Does the STBY 5V SW. circuit Q945
is turned on?
Check peripheral circuit of Q945,
Q946, Q950.
VC-TA352W/TA355/TA356
7. TROUBLESHOOTING
37
VC-TA350/TA351/351W
YES
YES
YES
NO
NO
NO
FLOW CHART NO.6 POWER TROUBLESHOOTING(6)
In case of output voltage at low level.
Check peripheral circuits IC902, IC921,
C933, R932, R929, R930 and R931.
The IC901, C913, R908, R909, R910 and R911 as
a result of check, if poor replace.
Check IC902 and peripheral circuits
pin(9) of IC901.
Replace IC901.
Check short-circuit or leak of T901.
Replace T901.
Check primary circuit and peripheral
circuit of Q901.
FLOW CHART NO.7 TIMER TROUBLESHOOTING
The flourescent display tube fails light up.
Is the supply voltage of 5V fed to pin(8)
of IC801?
Check STBY 5V line.
Is the supply negative voltage of -25V
fed to pin(1) of IC801?
Check negative voltage line(STBY
-25V) and power circuit.
Is the filament voltage applied
between (1)/(2) and (31)/(32) of the
fluorescent display tube?
Also negative voltage applied
between these pins and GND.
Check power circuit and peripheral
circuit of D952.
Does the fluorescent display tube
function?
Replace IC801.
Check for cracks on the fluorescent
display tube.
YES
YES
YES
YES
NO
NO
NO
NO
FLOW CHART NO.8 KEY CONTROL TROUBLESHOOTING(1)
Does the key switch make good
contact, when the cassette tape is
inserted?
Check switch contact.
Is there the function control voltage
inputted at pins (96),(97) and (98)
of IC701, when the jog shuttle ring
are activated?
Check peripheral circuit of pins(96),
(97) and (98) of IC701, and the jog
shuttle ring.
Replace IC701.
YES
NO
NO
YES
Key-in input is not received
<For jog shuttle mode.>
SW1(Pin96)
SW3(Pin97)
SW4(Pin98)
SW2(GND)
TERMINAL
ANGLE
0-10-20-30-40-50-60 10 20 30 40 50 60
-52 -38 -15 15 38 52
S882
STOP
TP801
TEST
TP803
KEY OFF
CASSETTE
S809
CH(-)
S810
SET/S.PICT
S892
S/PICT
S811
EJECT
S813
3.8V
4.4V
5.0V
SW 1/SW 2 INPUT VOLTAGE(V)
3.1V
2.5V
1.9V
1.2V
0.6V
STBY
S885FFS886
PLAY
S887
REW
S884
PAUSE/STILL
S883
REC
S891
T.SPEED
S807
CH(+)
S808
MENU
KEY 0 IN
KEY 1 IN
FLOW CHART NO.9 KEY CONTROL TROUBLESHOOTING(2)
Does the key switch make good
contact, when the cassette tape is
inserted?
Check switch contact.
Is there the function control voltage
inputted at the pins(87) and (88) of
IC701, when the keys are activated?
Replace IC701.
Check peripheral circuit of pins(87)
and (88) of IC701, and the function
keys.
YES
NO
NO
YES
Key-in input is not received
<Except for jog shuttle mode.>
VC-TA352W/TA355/TA356
38
VC-TA350/TA351/351W
FLOW CHART NO.10 INFRARED R/C TROUBLESHOOTING
No operation is possible from the infrared remote control.
Does the infrared remote control
function?
Replace infrared remote control as
required.
Is the supply voltage of 5V fed to C804
of (+) side?
Check AT 5V and GND lines.
Is "L" pulse sent out from pin(1) of the
receiver when the infrared remote
control is activated?
Replace receiver.
Check between at pin(1) of receiver and
all the way up through to pin (5) of IC701.
Replace IC701.
YES
NO
YES
NO
NO
NO
YES
Is the cassette housing distorted?
Fix or replace the cassette housing.
NO
YES
YES
YES
YES
NO
YES
NO
NO
YES
NO
YES
FLOW CHART NO.11 CASSETTE CONTROL TROUBLESHOOTING(1)
A cassette tape is not take in.
NO
NO
Check start sensor cover.
Check line between start sensor and
pin (79) of IC701
Check line between pin (91) of IC701
and pin(11) of IC706.
Is the supply voltage of 12V fed to pin
(9) of IC706?
Check M 12V lines.
Check IC706.
Check line between IC706 and loading
motor.
Replace loading motor.
Is the specified voltage applied at the
loading motor terminal when the
cassette tape is inserted?
Does pin(12) of IC706 change to about
10V when the cassette tape in inserted?
Does pin(13) of IC706 go to a "H" level
when the cassette tape is inserted?
Does pin(79) of IC701 change from"H"
to "L" level when the cassette tape is
inserted?
Does the start sensor cover go to open
when the cassette tape is inserted?
NO
NO
NO
FLOW CHART NO.12 CASSETTE CONTROL TROUBLESHOOTING(2)
A cassette tape is taken in, but ejected at once.
Does the start sensor pulse at pin (79)
of IC701 change from "L" to "H" level
when the cassette tape is loaded?
Check line between start sensor and pin
(79) of IC701.
Does the end sensor pulse at pin (85)
of IC701 change from "L" to "H" level
when the cassette tape is loaded?
Check line between end sensor and pin
(85) of IC701.
Does the master cam mode shifter
operate normally when the cassette
tape is loaded?
Check line between cam switch and
IC701.
Replace IC701.
YES
YES
YES
FLOW CHART NO.13 LOADING MOTOR AND EJECT TROUBLESHOOTING
The cassette tape fails to come out.
Does the capstan motor start when the
EJECT button is pressed?
See FLOW CHART NO.14 CAPSTAN
MOTOR TROUBLESHOOTING
Does the take-up reel disk turn when the
capstan motor is running?
Check line between take-up reel
sensor and pin(2) of IC701.
Is a "H" level applied at pin(12) of IC706
when a reel pulse has been inputted?
Check line between pin(90) of IC701
and pin(12) of IC706.
Is the supply voltage of 12V fed to
pin(9) of IC706?
Is the voltage about 10V sent out from
pin(15) of IC706?
Check IC706.
Is the specified voltage applied at the
loading motor terminal?
Check line between IC706 and
loading motor.
Does the loading motor run? Replace loading motor.
Replace cassette cam, gear, etc.
YES
YES
YES
Check M 12V lines.
NO
YES
NO
YES
YES
YES
NO
NO
NO
NO
NO
VC-TA352W/TA355/TA356
39
VC-TA350/TA351/351W
FLOW CHART NO.15 DRUM MOTOR TROUBLESHOOTING(1)
The drum motor fails to run.
Is the voltage more than about 2.6V
DC given out of pin(46) of IC701?
Check IC701.
NO
NO
NO
YES
YES
Check PC 5V line.
Is the supply voltage of 5V fed to pin
(3) of IC706?
Is the voltage more than about 2.6V
DC given out of pin(2) of IC706?
Check line between pin(46) of IC701
and pin(2) of IC706.
NO
YES
YES
Is the supply voltage of 12V fed to
pin(21) of IC706?
Replace drum motor.
Check M 12V line.
FLOW CHART NO.14 CAPSTAN MOTOR TROUBLESHOOTING
The capstan motor fails to run.
Is the voltage more than about 2.6V
DC given out of pin(29) of IC701?
Check IC701.
NO
NO
NO
NO
NO
YES
YES
YES
YES
Is the supply voltage of 5V fed to
pin(8) of AC connector?
Check PC 5V line.
Is the voltage more than 2.6V DC
sent in pin(4) of AC connector?
Check line between the AC connector
and pin(29) of IC701?
Is the voltage of pin(3) of AC
connector 1.6~2.7V?
Check line between the pin(92) of
IC701 and pin(3) of AC connector.
Is the supply voltage of 12V/20V fed
to pin(5) of AC connector?
YES
Replace capstan motor.
Check MOTOR Vcc line and motor
voltage selector circuit.
(Q995, 996)
FLOW CHART NO.16 DRUM MOTOR TROUBLESHOOTING(2)
The drum motor runs only for a few seconds.
Replace IC706.
Check peripheral circuit of pins (4), (5)
and (6) of IC706.
Is drum PG signal given out from the
pin (7) of IC706?
Is drum PG signal fed to pin(66) of
IC701?
Check line between pin(7) of IC706
and pin(66) of IC701.
Is head switching pulse sent out from
the pin(23) of IC701?
Check IC701.
Replace IC701.
NO
Check drum motor.
YES
YES
YES
YES
NO
NO
NO
D-FG
about 5Vp-p
D-PG
about 5Vp-p
YES
NO
YES
YES
NO
NO
FLOW CHART NO.17 HEAD SWITCHING PULSE TROUBLESHOOTING.
No head switching pulse.
See FLOW CHART NO.15, 16 (DRUM
MOTOR TROUBLESHOOTING(1), (2))
Is the drum motor rotating?
Is the drum PG signal and drum FG
signal present on pins(66) and (65) of
IC701, respectively?
Replace IC701.
Check line between IC706 and
IC701.
Check peripheral circuit of IC706.
Are the drum PG signal and drum
FG signal present on pins (7), (8)
of IC706?
VC-TA352W/TA355/TA356
40
VC-TA350/TA351/351W
FLOW CHART NO.18 DRUM SERVO TROUBLESHOOTING
Drum servo does not function.
Check peripheral circuit of X701.
Is there 14.318MHz oscillation at
pins(37) and (38) of IC701?
NO
In PB mode
YES
In REC mode
Is there drum FG signal at pin(65) of
IC701 present?
Is the V-SYNC signal(reference) at pin
(50) of IC701?
YES
NO
NO
Check peripheral circuit of pin(50) of
IC701, C770, C771 and R770.
Check drum FG signal line.
Is the head switching pulse at pin (23) of
IC701 present?
NO
See FLOW CHART NO.17
(HEAD SWITCHING PULSE TROUBLE-
SHOOTING.)
YES
YES
Is the drum APC output at pin (34) of
IC701 and drum AFC output at pin (32)
of IC701 present?
NO
Replace IC701.
YES
YES
Is the drum control voltage applied to
pin(2) of IC706?
YES
Is pin(46) of IC701 in high impedance?
NO
YES
Check line between pins(34) and (32)
of IC701 and pin(2) of IC706.
Does the IC706 operate normally?
Replace IC701.
Replace drum motor.
NO
1
FLOW CHART NO.19 CAPSTAN SERVO TROUBLESHOOTING
Capstan servo does not function.
Only PB mode inoperative
YES
NO
Check "1"
Check capstan motor unit and/or replace.
Is there capstan AFC and APC at pins(31)
and (33) of IC701?
Replace A/C head.
YES
NO
YES
NO
NO
YES
NO
Is there capstan AFC signal at pin (31) of
IC701?
Replace IC701.
NO
Is there REC CTL signal output at pins
(75) and (74) of IC701?
Does PB CTL signal appear at pin (76) of
IC701?
Does A/C head operate normally?
Adjust the height of the A/C head.
Check the capstan FG signal line between
pin(6) of AC connector and pin(67) of
IC701.
Check peripheral circuit of AC connector.
Are REC and/or PB mode inoperative?
Check "2"
NO
YES
YES
YES
Does pin(29) of IC701 operate normally?
NO
NO
Is there capstan APC signal at pin (33) of
IC701?
Does PB CTL signal appear at pin (76) of
IC701?
Replace IC701.
2
Only REC mode inoperative
NO
Check peripheral circuit of pin(50) of
IC701, C770, C771 and R770.
Is the V-SYNC signal(reference) at pin(50)
of IC701?
NO
Replace IC701.
YES
YES
Does the capstan FG signal appear at pin
(67) of IC701?
YES
NO
NO
Check peripheral circuit of X701.
Is there 14.318MHz oscillation at pins(37)
and (38) of IC701?
A
A
VC-TA352W/TA355/TA356
41
VC-TA350/TA351/351W
FLOW CHART NO.20 E-E MODE TROUBLESHOOTING
No picture E-E signal.
NO
NO
NO
NO
NO
YES
YES
YES
Is there picture signal inputted
in the pins(28), (30) and (31)
of IC201?
1For ext. input mode.
Check line between rear video input terminal and pin(30) of IC201.
Check line between front video input terminal and pin(28) of IC201.
2For U/V tuner mode.
Check line between video output (TP101) of IF circuit and pin(31)
of IC201.
Is the supply voltage of 5V
(Y-Vcc) fed to pin(12) of
IC201?
Check Y/C 5V line.
Check line between pin(52) of
IC201, and pin(49) of IC701.
YES
YES
YES
YES
Is there a picture signal
outputted in the emitter of
Q251?
Check peripheral circuit of
Q251
NO
NO
Is there Y/C serial data and
Y/C clock signal applied to
pins(63) and (62) of IC201?
Check line between pins(63),
(62) of IC201 and pins(56),
(57) of IC701.
Is the supply voltage of 5V
(OSD-Vcc) fed to pin(51) of
IC701?
Replace IC201.
NO
Check PC 5V line.
1Line output : Check the line between Q251 peripheral and output
terminal periphery.
2RF output : Check the line between Q251 peripheral and RF
video input terminal of tuner periphery.
Is there a picture signal
outputted in the pin(52) of
IC201?
Is there a picture signal
inputted in the pin(49) of
IC701?
Is there a picture signal
outputted in the pin(47) of
IC701?
VC-TA352W/TA355/TA356
42
VC-TA350/TA351/351W
FLOW CHART NO.21 RECORDING MODE TROUBLESHOOTING
Picture (Luminance) record is impossible (E-E mode is possible).
NO
NO
NO
NO
NO
YES
Is there luminance signal (approx. 0.5Vp-p)
input in the pin (19) of IC201?
Check line between pins (18) and (19) of IC
201.
YES
Is there luminance signal (approx. 0.3Vp-p)
input in the pin (42) of IC201?
Check line between pins (21) and (42) of
IC201 (C208).
YES
Is there luminance signal (approx. 0.5Vp-p)
input in the pin (23) of IC201?
Check line between pins (24) and (23) of
IC201 (C210).
YES
Is there luminance signal (approx. 0.5Vp-p)
input and output in the pins (13) and (14) of
IC201, respectively?
Check peripheral circuit of pins (13) and (14)
of IC201 (R201,R202, C203).
YES
YES
Is there luminance signal (approx. 0.5Vp-p)
input in the pin (26) of IC201?
Check line between pins (39) and (26) of
IC201 (C212).
NO
Is there luminance signal (aprox. 0.5Vp-p)
input in the pin (39) of IC201?
YES
Is voltage 5V applied to the CCD section
power terminal at pin (36) of IC201?
Is CCD control voltage approx. 5V applied
normally to the pin (37) from pin (57) of IC201?
Is clock signal (approx.
8.86MHz<PAL mode> or
7.16MHz<NTSC mode>/0.5Vp-p)
for CCD applied normally to the pin (44) from
(69) of IC201?
Although picture record is possible, colour does not appear in
PAL or NTSC mode (E-E mode is possible).
NO
NO
NO
YES
Is voltage of 5V applied to the chroma power
terminal at pin (61) of IC201?
Check peripheral circuit pin (61) of IC201 and
Y/C 5V line.
Is there chroma signal
(approx. 156mVp-p <PAL mode> or
298mVp-p<NTSC mode>/burst)
input in the pin (46) of IC201?
Check line between pins (60) and (46) of
IC201 (C512).
Is there chroma signal (approx.
197mVp-p <PAL mode> or
375mVp-p<NTSC mode>/burst) input in
the pin (58) of IC201?
Check line between pins (58) and (35) of
IC201 (R505, C515).
YES
For PAL/SECAM mode.
Check whether the pins(73) and (75) of IC201 oscillate 4.43MHz.
For NTSC mode.
Check whether the pins(73) and (71) of IC201 oscillate 3.58NHz.
NO
YES
For PAL/SECAM mode.
Check parts arround of X501.
For NTSC mode.
Check parts arround of X502.
Is there chroma signal (approx.
197mVp-p <PAL mode> or
375mVp-p<NTSC mode>/burst) input in
the pin (35) of IC201?
YES
NO
SP mode:
Is there record FM signal (approx. 20mVp-p) output at pins (88), (89)
<<SP1>> and pins (86), (87) <<SP2>>of IC201?
LP(PAL, SECAM)/EP(NTSC) mode:
Is there record FM signal (approx. 20mVp-p) output at pins (93), (94)
<<EP1>> and pins (92), (91)<<EP2>>of IC201?
SP mode:
Is there chroma ingredient included signal (approx. 20mVp-p) output at
pins (88), (89)<<SP1>> and pins (86), (87)<<SP 2>> of IC201?
LP(PAL, SECAM)/EP(NTSC) mode:
Is there chroma ingredient included signal (approx. 20mVp-p) output at
pins (93), (94)<<SP1>> and pins (92), (91)<<SP 2>> of IC201?
YES
Check or replace the cylinder.
NO
YES
YES
Is the supply voltage of 5V (PRE/REV Vcc)
fed to pin (90) of IC201?
Replace IC201.
VC-TA352W/TA355/TA356
43
VC-TA350/TA351/351W
FLOW CHART NO.22 PLAYBACK MODE TROUBLESHOOTING
Playback picture does not appear (E-E mode is possible).
NO
YES
Is there FM signal (approx. 0.4Vp-p) input in
the pin (78) of IC201?
YES
Check line between pins (79) and (78) of
IC201.
YES
NO
Is there luminance signal (approx. 0.25Vp-p)
input and output in the pins (13), (14) and
(17) of IC201?
Check peripheral circuit of pins (13), (14) and
(17) of IC201.
YES
NO
Is there luminance signal (approx. 0.5Vp-p)
inputted at pin (19) of IC201?
Check line between pins (18) and (19) of
IC201 (C206).
YES
NO
Is there luminance signal (approx. 0.3Vp-p)
inputted at pin (42) of IC201?
Check line between pins (21) and (24) of
IC201 (C208).
YES
NO
Is there luminance signal (approx. 0.5Vp-p)
inputted at pin (26) of IC201?
YES
NO
Is there luminance signal (approx. 0.5Vp-p)
inputted at pin (23) of IC201?
Check line between pins (39) and (26) of
IC201 (C212).
Is there luminance signal (approx. 0.4Vp-p)
output in the pin (79) of IC201?
NO
Is the supply V-H.SW.P signal fed to pin
(81) of IC201?
NO
Check V-H.SW.P line.
YES
Is there luminance signal (approx. 0.5Vp-p)
output in the pin (39) of IC201?
NO
Although picture playback is possible, colour does not appear
in PAL or NTSC mode (E-E mode is possible).
NO
YES
Is voltage 5V applied to the chroma power
terminal at pin (61) of IC201?
YES
Check peripheral circuit of pins (61) of IC201
and Y/C 5V line.
NO
Is there chroma signal (approx.
156mVp-p <PAL mode> or
298mVp-p<NTSC mode> /burst)
input in the pin (46) of IC201?
YES
NO
Is there chroma signal (approx.
197mVp-p <PAL mode> or
375mVp-p<NTSC mode>/ burst)
input in the pin (58) of IC201?
Check line between pins (58) and (35) of
IC201 (R505, C515).
NO
NO
YES
Is there chroma signal (approx.
300mVp-p <PAL mode> or
286mVp-p<NTSC mode>/burst)
output from the pin (55) of IC201?
Replace IC201.
Is there chroma signal input at pin (54)
of IC201?
NO
Check line between pins (55) and (54) of
IC201 (C514).
Check line between pins (60) and (46) of
IC201 (C512).
YES
For PAL/SECAM mode.
Check whether the pins(73) and (75) of
IC201 oscillate 4.43MHz.
For NTSC mode.
Check whether the pins(73) and (71) of
IC201 oscillate 3.58NHz.
NO
For PAL/SECAM mode.
Check parts arround of X501.
For NTSC mode.
Check parts arround of X502.
Is there chroma signal (approx.
197mVp-p <PAL mode> or
375mVp-p<NTSC mode>/ burst)
input in the pin (35) of IC201?
NO
YES
Is voltage 5V applied to the CCD section power terminal at pin (36) of IC201?
Check line between pins (24) and (23) of IC201 (C210).
NO
Is there video signal (approx. 2.0Vp-p)
outputted at pin (52) of IC201?
Replace IC201.
Is CCD control voltage approx. 5V normally to the pin (37) from pin (57) of IC201?
Is clock signal (approx. 8.86MHz<PAL mode> or 7.16MHz<NTSC mode>/0.5Vp-p) for CCD applied normally to the pin (44) from (69) of IC201?
VC-TA352W/TA355/TA356
44
VC-TA350/TA351/351W
YES
YES
YES
YES
NO
NO
NO
FLOW CHART NO.24 LINEAR SOUND MODE TROUBLESHOOTING(1)
Check line between pin(99) of IC201 and
pin(21) of IC701.
Is there audio signal outputted at pin(11) of
IC201?
Does fh trap circuit operate normally?
(Q604)
Line output terminal :
Check line ranging from fh trap circuit to the audio output terminal.
RF output terminal :
Check line ranging from fh trap circuit to the audio input terminal of tuner (TU101).
NO
NO
Is there audio signal inputted at each input
terminal of IC201 as shown in table?
U/V tuner audio input terminal.
Normal audio input terminal.
pin(9)
pin(8)
Check line ranging from IF circuit.
Check line ranging from EXT. audio input
terminal
Replace IC201.
Is there "L" level at pin(99) of IC201?
No E-E sound heard.
Check fh trap circuit.(Q604)
NO
NO
NO
FLOW CHART NO.25 LINEAR SOUND MODE TROUBLESHOOTING (1)
Is there "L" level at pin (99) of IC201?
Is there a signal at pin(4) of IC201?
YES
YES
No linear sound recording
Is the supply voltage of 12V fed to pin(2) of
T601?
Check the AUDIO MUTE (H) line between pin
(99) of IC651 and pin (21) of IC701.
Replace IC201.
Check PC 12V line.
NO
YES
YES
Is there signal (Bias) at pin (5) of T601?
Check the Bias oscillation circuit (T601,Q602,
Q603) and FE BIAS CTL line.
NO
Is there signal (Bias + Audio sig.) at pin (6)
of T601?
YES
Check the MH-AM harness and A/C head.
Check peripheral circuits of T601.
YES
NO
NO
NO
NO
NO
FLOW CHART NO.26 LINEAR SOUND MODE TROUBLESHOOTING (2)
YES
YES
Clean A/C Head.
Is the azimuth hight of A/C head properly
adjusted?
Replace A/C head.
Is there "L" level at pin (99) of IC201?
Is there a signal at pin(11) of IC201?
YES
YES
Are the MH-AA harness and the PB AMP
peripheral parts normal?
Readjust azimuth hight.
YES
No linear sound playback
Is there a signal at pin(100) of IC201?
Does fh trap circuit operate normally?
(Q604)
YES
Check line ranging from EXT. terminal to
audio output terminal.
Check the AUDIO MUTE (H) line between pin
(99) of IC201 and pin (21) of IC701.
Replace IC201.
Check fh trap circuit. (Q604)
VC-TA352W/TA355/TA356
45
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
REPLACEMENT OF IC710(E2PROM)
Servicing precautions When the IC710(E2PROM) has been replaced, make the following reprogramming. Depending on models, the IC710(E2PROM) has been factory adjusted for it’s memory function. It’s therefor necessary to reprogram the memory function for the model in question. Note that the servo circuit requires readjustments for the slow and still modes.
1. Memory function reprogramming.
1. Check the power off.(Power is standby mode)
2. Make for moment short-circuit test point (TP801), located at the front side on the main PWB.” Be sure that all the fluorescent display tube light up into the TEST mode.
3. Using the CHANNEL(+) AND (-) buttons, select the right function numbers from JP0ü`J39, which appear in the fluorescent display tube, referring to the E2PROM map. Press the DISPLAY button to pickup the functions (ON) and the CLEAR button to discard the functions(OFF). DISPLAY and CLEAR buttons, are located on the remote control unit.
when the DISPLAY button has been pressed (ON), the memory function number starts flashing.when the CLEAR button has been pressed (OFF), the memory function number lights up.
4. Press the FF button on the remote control unit. By doing, lower 5 of the 10 digits are displayed in hexadecimal notation. Example : "ON" and "OFF" are taken as "1" and "0" respectively.
JP19 JP18 JP17 JP16 JP15 JP14 JP13 JP12 JP11 JP10 JP9 JP8 JP7 JP6 JP5 JP4 JP3 JP2 JP1 JP0
01100110001000010011
↓↓ ↓↓↓
66 213
5. Press the STOP button on the remote control unit. By doing, upper 5 in the 10 digits are displayed in hexadecimal notation from the feature function.” Example : "ON" and "OFF" are taken as "1" and "0" respectively.
JP39 JP38 JP37 JP36 JP35 JP34 JP33 JP32 JP31 JP30 JP29 JP28 JP27 JP26 JP25 JP24 JP23 JP22 JP21 JP20
00110110000000001000
↓↓ ↓↓↓
36 008
2. Memory recording preset level reprogramming.
1. Similarly to the above step 1-1 and 2 the same operate.
2. Using the CHANNEL (+) AND (-) buttons, select the right function numbers continued from recording preset number as has been <LP p ∗ ∗ to SP p ∗ ∗>, which appear in the fluorescent display tube, referring to the E2PROM map.
3. Recording level preset number selected from the ten keys on the remote control unit, which appear in the fluorescent display tube, referring to the E2PROM map.
4. Example : SP or LP p ∗ ∗
↑↑
Tape speed Chrominance preset number. (from "0" to "7")
Luminance preset number. (from "0" to "7") System (p : PAL)
5. When press the REW button on the remote control unit. By doing, PAL system recording level preset number selected from the ten keys on the remote control unit which appear in the fluorescent display tube, referring to the E2PROM map.
LP p ∗∗LP p SP p ∗∗SP p
selection from the selection from the selection from the selection from the ten keys. ten keys. ten keys. ten keys. (from "0" to "7") (from "0" to "7") (from "0" to "7") (from "0" to "7")
↑↑↑↑
6. When press the PLAY button on the remote control unit. By doing, NTSC system recording level preset number selected from the ten keys on the remote control unit which appear in the fluorescent display tube, referring to the E2PROM map.
EP p ∗∗EP p SP p ∗∗SP p
selection from the selection from the selection from the selection from the ten keys. ten keys. ten keys. ten keys. (from "0" to "7") (from "0" to "7") (from "0" to "7") (from "0" to "7")
↑↑↑↑
3. Finally make for a moment short-circuit test point (TP801), located at the front side on the main PWB to clear the TEST mode.
46
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
ROM MAP
MODEL VC-TA350/355 EP n ∗ ∗ NTSC Luminance level 3 0 4 EP n ∗ ∗ NTSC Chrominance level 4 0 3 SP n ∗ ∗ NTSC Luminance level 4 5 5 SP n ∗ ∗ NTSC Chrominance level 4 4 3 LP p ∗ ∗ PAL Luminance level 3 0 4 LP p ∗ ∗ PAL Chrominance level 4 0 3 SP p ∗ ∗ PAL Luminance level 4 5 4 SP p ∗ ∗ PAL Chrominance level 4 4 4 JP39 A.DUB 0 0 0 JP38 NOT SLOW ATR 0 0 0 JP37 INSTANT REPLAY 0 0 0 JP36 NTPB 1 1 1 JP35 NTSC SKEW 0 0 0 JP34 HEAD2 1 1 1 JP33 HEAD1 0 1 1 JP32 HEAD0 1 0 0 JP31 GAMMA 0 0 0 JP30 L.P 5MIN. 0 0 0 JP29 POSI89 1 1 1 JP28 R/C CODE 1/2 0 0 0 JP27 DNR 0 0 0 JP26 POST CODE 0 0 0 JP25 SAT CTL 0 0 0 JP24 AV LINK 0 0 0 JP23 Hi-Fi 0 0 0 JP22 SORT/AUTO CLOCK 0 0 0 JP21 DECODER 0 0 0 JP20 DOLBY SURROUND 0 0 0 JP19 NICAM 1 0 0 0 JP18 NICAM 0 0 0 0 JP17 G-CODE 1 0 0 1 JP16 G-CODE 0 0 0 0 JP15 OEM 1 1 1 JP14 LP 0 1 1 JP13 FRONT AV 0 0 1 JP12 DUBLE SCART 0 0 0 JP11 NOT RF OUT 0 0 0 JP10 TUNER 2 1 1 1 JP 9 TUNER 1 1 1 1 JP 8 TUNER 0 0 0 0 JP 7 SYSTEM 1 1 1 1 JP 6 SYSTEM 0 0 0 0 JP 5 SAT CH VPS OFF 0 0 0 JP 4 LOW POWER 1 1 1 JP 3 SPATIALIZER 0 0 0 JP 2 VPS/PDC 0 0 0 JP 1 COLOR 1 0 0 0 JP 0 COLOR 0 0 0 0
DISPLAY IN HEXADECIMAL NOTATION
JP DISPLAY 1(FF) 15200 16200 16200 JP DISPLAY 2(STOP) 08690 0C690 2E690 Y/C CURRENT 1(REW) 0756 4344 4344 Y/C CURRENT 2(PLAY) 0756 4356 4353
VC-TA351/351W/TA356
VC-TA352
47
0:LIGHT UP 1:FLASHING
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
8.BLOCK DIAGRAM
SYSTEM SERVO BLOCK DIAGRAM
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
48
49
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
SIGNAL FLOW BLOCK DIAGRAM
PB Chrominance Signal PB Luminance Signal
REC Chrominance Signal REC Luminance Signal
E-E Signal
50
51
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
AUDIO BLOCK DIAGRAM
FROM SYSTEM M/DK(H) (Pin 82 of IC701)
FROM SYSTEM M/I(H) (Pin 89 of IC701)
VIDEO OUT
f
AFT
d
s
AUDIO OUT
a
p
o
N.C
AFT_S_CURVE (Pin 84 of IC701)
EE Signal
PB Audio Signal REC Audio Signal
AT 5V
52
53
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
POWER CIRCUIT BLOCK DIAGRAM
54
SCHEMATIC DIAGRAM
IMPORTANT SAFETY NOTICE: BE SURE TO USE GENUINE PARTS FOR SE­CURING THE SAFETY AND RELIABILITY OF THE SET. PARTS MARKED WITH " å " AND PARTS SHADED (IN BLACK) ARE ESPECIALLY IMPOR­TANT FOR MAINTAINING THE SAFETY AND PROTECTING ABILITY OF THE SET. BE SURE TO REPLACE THEM WITH PARTS OF SPECIFIED PART NUMBER.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIOL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
NOTES:
1. The unit of resistance "ohm" is omitted (k=1000 ohm, M=1 Meg ohm).
2. All resistors are 1/8 watt, unless otherwise noted.
3. The unit of capacitance "F" is omitted (µ=µF, p=µµF).
4. The values in parentheses are the ones in the PB mode; the values without parentheses are the ones in the REC mode.
VOLTAGE MEASUREMENT CONDITIONS:
1. DC voltages are measured between points indi­cated and chassis ground by VTVM, with AC110~240V, 50/60Hz supplied to unit and all controls are set to normal viewing picture unless otherwise noted.
2. Voltages are measured with 10000µV B & W or colour noted.
WAVEFORM MEASUREMENT CONDITIONS: 10000µV 87.5 percent modulated colour bar signal is
fed into tuner.
CAUTION: This circuit diagram is original one. Therefore there may be a slight difference from yours.
10 11 12 13 14 15 16 17 18 19
55
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
9.SCHEMATIC DIAGRAM AND PWB FOIL PATTERN
MAIN CIRCUIT(1)
J
I
H
G
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
F
E
K
D
C
B
A
1 2 3 4 5 6 7 8 9
* VOLTAGE MEASUREMENT MODE
PB ...... Parentheses ( )
REC ... Without Parentheses
56
10 11 12 13 14 15 16 17 18 19
57
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MAIN CIRCUIT(2)
J
I
H
G
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9
* VOLTAGE MEASUREMENT MODE
PB ...... Parentheses ( )
REC ... Without Parentheses
58
10 11 12 13 14 15 16 17 18 19
59
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MAIN CIRCUIT(3)
J
I
H
G
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
F
E
D
C
STBY -25V SW
B
A
1 2 3 4 5 6 7 8 9
* VOLTAGE MEASUREMENT MODE
PB ...... Parentheses ( )
REC ... Without Parentheses
60
10 11 12 13 14 15 16 17 18 19
61
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MAIN CIRCUIT(4)
J
I
H
G
DJ106
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10
* VOLTAGE MEASUREMENT MODE
PB ......Parentheses ( )
REC ...Without Parentheses
62
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
LED CIRCUIT
J
I
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10
10 11 12 13 14 15 16 17 18 19
63
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
OPERATION CIRCUIT
J
I
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10
64
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
PWB FOIL PATTERN
LED PWB
J
I
H
G
F
OPERATION PWB
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10
10 11 12 13 14 15 16 17 18 19
65
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
MAIN PWB
J
I
H
G
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9
66
10 11 12 13 14 15 16 17 18 19
67
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
10. REPLACEMENT PARTS LIST
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PARTS REPLACEMENT
Parts marked with " å " are important for maintaining the safety of the set.Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
5. PRICE CODE
HOW TO IDENTIFY CHIP
TRANSISTORS AND
DIODES BY ITS MARKING
(1)
(3)
(2)
Package Marking Parts No.
Fig. 1 FQ VS2SA1037KQ-1 Fig. 1 BQ VS2SC2412KQ-1
Fig. 1
Marking
(1) Base/Input (2) Emitter/Ground (3) Collector/Output
IC801 VHIMN12511/-1 V MN12511 AQ IC921 VHIKIA431//-1 V KIA431 AE
TRANSISTORS
Q251 VS2SA1530ARS1 V 2SA1530ARS AC Q304 VS2SC3052EF-1 V 2SC3052EF AC Q305 VSKRC103S//-1 V KRC103S AA Q306 VS2SA1530ARS1 V 2SA1530ARS AC Q602 VS2SC3203Y/-1 V 2SC3203Y AB Q603 VS2SC3052EF-1 V 2SC3052EF AC Q604 VSIMX9/////-1 V IMX9 AC Q704 VS2SA1530ARS1 V 2SA1530ARS AC Q705 VS2SC3052EF-1 V 2SC3052EF AC Q706 VS2SA1530ARS1 V 2SA1530ARS AC Q710 VS2SC3052EF-1 V 2SC3052EF AC Q711 VS2SC3052EF-1 V 2SC3052EF AC Q853 VSKRA103S//-1 V KRA103S AA
å Q901 VS2SK2848//-1 V 2SK2848 AH
Q902 VS2SC2001LK-1 V 2SC2001LK AA Q903 VS2SC3576AC-1 V 2SC3576AC AC Q940 VS2SA1530ARS1 V 2SA1530ARS AC Q941 VSKRC103S//-1 V KRC103S AA Q942 VS2SB1443TV1E V 2SB1443T AE Q943 VSKRC102S//-1 V KRC102S AA Q944 VSKRC102S//-1 V KRC102S AA Q945 VS2SA1271-Y-1 V 2SA1271-Y AB Q946 VSKRC103S//-1 V KRC103S AA Q947 VS2SC3203Y/-1 V 2SC3203Y AB Q948 VSKRA103S//-1 V KRA103S AA Q949 VSKRC103S//-1 V KRC103S AA Q950 VSKRC103S//-1 V KRC103S AA Q951 VS2SB1443TV1E V 2SB1443TV AE Q952 VSKRC103S//-1 V KRC103S AA Q953 VSKRC102S//-1 V KRC102S AA Q981 VS2SA1271-Y-1 V 2SA1271-Y AB Q982 VSKRC103S//-1 V KRC103S AA Q991 VS2SD471-KL1E V 2SD471-KL AC Q992 VS2SA1530ARS1 V 2SA1530ARS AC Q993 VSKRC103S//-1 V KRC103S AA Q995 VSKRC102S//-1 V KRC102S AA
MARK : SPARE PARTS-DELIVERY SECTION
Ref. No. Part No. Description Code
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
DUNTK5941TEVC - Main Unit(VC-TA350,
TA355)
DUNTK5941TEVD - Main Unit(VC-TA351,
TA356) DUNTK5941TEVE - Main Unit(VC-TA351W) — DUNTK5941TEVL - Main Unit(VC-TA352W) — DUNTK5942TEV2 - Operation Unit — DUNTK5977TEV1 - LED Unit
DUNTK5941TEVC/VD/VE/VL
MAIN Unit
TUNER
NOTE: THE PARTSHERE SHOWN ARE SUPPLIED ASAN
ASSEMBLY BUT NOT INDEPENDENTLY.
TU101 VTUATMDG2-801 V Tuner BF
INTEGRATED CIRCUITS
IC201 VHIHA8317F/-1 V HA118317F BA IC601 VHIBA7755A/-1 V BA7755A AE IC701 RH-IX1593GEN4 J I.C. AY IC702 VHIPST600K/-1 V IC-PST600K-2 AE IC706 VHILB1988//-1 V LB1988 AQ IC710 VHIS24C02A/-1 V S-24C02AFJ-TB AK
DG801 VVKSTV6SS50-1 V Display AU
DIODES
D701 RH-PX0270GEZZ J Photodiode AC D702 VHD1SS119//-1 V 1SS119 AB D706 RH-PX0252GEZZ J GP1S563 AF D707 RH-PX0252GEZZ J GP1S563 AF D708 RH-PX0238GEZZ J RPI-352S AF D709 RH-PX0238GEZZ J RPI-352S AF D710 VHD1SS119//-1 V 1SS119 AB D712 VHD1SS119//-1 V 1SS119 AB D715 VHD1SS119//-1 V 1SS119 AB D716 VHD1SS119//-1 V 1SS119 AB
å D901 VHDRL105G//-1 V RL105G AB å D902 VHDRL105G//-1 V RL105G AB å D903 VHDRL105G//-1 V RL105G AB å D904 VHDRL105G//-1 V RL105G AB å D905 VHDERA2206/-1 V ERA2206 AC å D907 VHDRL105G//-1 V RL105G AB å D908 RH-EX0645GEZZ J Zener Diode AB å D909 VHD1SS119//-1 V 1SS119 AB
D910 RH-EX0613GEZZ J Zener Diode AA D912 VHD1F4G////-1 V 1F4G AC D913 VHD1SS119//-1 V 1SS119 AB D915 RH-EX0617GEZZ J Zener Diode AA D921 VHD1F4G////-1 V 1F4G AC D922 VHD1F4G////-1 V 1F4G AC D923 VHD1F4G////-1 V 1F4G AC D924 VHD15DF1FC/1E V 15DF1FC AD D925 VHDRK34////-1 V RK34 AE D926 VHD1SS147//-1 V 1SS147 AA D940 VHD1SS119//-1 V 1SS119 AB D941 RH-EX0613GEZZ J Zener Diode AA D951 RH-EX0677GEZZ J Zener Diode AB D952 RH-EX0601GEZZ J Zener Diode AA
68
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
D991 RH-EX0631GEZZ J Zener Diode AA D992 VHD1SS119//-1 V 1SS119 AB D993 VHDRL1N4004-1 V RL1N400 AD D994 VHDRL1N4004-1 V RL1N400 AD
å IC901 RH-FX0001AJZZ V TCET1103G AE å IC902 RH-FX0001AJZZ V TCET1103G AE
Q701 RH-PX0233GEZZ J PT493FL2 AD Q702 RH-PX0233GEZZ J PT493FL2 AD
PACKAGED CIRCUITS
å VA901 RH-VX0048CEZZ V Varistor AE
CRYSTALS
X501 RCRSB0265GEZZ J Crystal AH X502 RCRSB0232GEZZ J Crystal AG X701 RCRSB0205GEZZ J Crystal AM X702 RCRSB0138GEZZ J Crystal AD X770 RCRSB0184GEZZ J Crystal AM
COILS AND TRANSFORMERS
L101 VP-CF100K0000 V Peaking 10µHAB L102 VP-MK101K0000 V Peaking 100µHAB L103 VP-XF100J0000 V Peaking 10µHAB L107 VP-XF100J0000 V Peaking 10µHAB L113 VP-XF2R7K0000 V Peaking 2.7µHAB L201 VP-XF221K0000 V Peaking 220µHAB L301 VP-MK101K0000 V Peaking 100µHAB L302 VP-XF180K0000 V Peaking 18µHAB L303 VP-ZK102K0000 V Peaking 1000µHAB L502 VP-XF560K0000 V Peaking 56µHAB L503 VP-XF120K0000 V Peaking 12µHAB L602 VP-DF221K0000 V Peaking 220µHAB
å L901 RCILF0009AJZZ V Coil AK
L922 RCILP0171CEZZ V Coil AD L923 RCILP0175CEZZ V Coil AD T601 RTRNH0098GEZZ J OSC. Transformer AE
å T901 RTRNZ0140AJZZ V Transformer AN
CAPACITORS
C102 VCKYCY1HB562K V 5600p 50V Ceramic AA C103 VCEA9M0JW227M V 220 6.3V Electrolytic AB C106 VCEA9M0JW227M V 220 6.3V Electrolytic AB C108 VCCCCY1HH470J V 47p 50V Ceramic AA C109 VCCCCY1HH470J V 47p 50V Ceramic AA C112 VCEA9M1HW105M V 1 50V Electrolytic AB C114 VCKYCY1CF104Z V 0.1 16V Ceramic AA C115 VCKYD41HB681K V 680p 50V Ceramic AA C116 VCEA9M0JW476M V 47 6.3V Electrolytic AB C117 VCCSD41HL470J V 47p 50V Ceramic AA C118 VCCCCY1HH271J V 270p 50V Ceramic AA C201 VCEA9M0JW107M V 100 6.3V Electrolytic AB C202 VCKYCY0JF105Z V 1 6.3V Ceramic AB C203 VCCCCY1HH151J V 150p 50V Ceramic AA C204 VCKYCY1CB104K V 0.1 16V Ceramic AB C205 VCCSD41HL270J V 27p 50V Ceramic AA C206 VCKYCY1CF104Z V 0.1 16V Ceramic AA C207 VCKYCY1CF104Z V 0.1 16V Ceramic AA C208 VCEA9M1CW106M V 10 16V Electrolytic AB C209 VCKYCY1CF104Z V 0.1 16V Ceramic AA C210 VCKYCY1CF104Z V 0.1 16V Ceramic AA C211 VCEA9M1HW335M V 3.3 50V Electrolytic AB C212 VCEA9M1CW106M V 10 16V Electrolytic AB C213 VCEA9M1HW225M V 2.2 50V Electrolytic AB C214 VCKYCY0JF105Z V 1 6.3V Ceramic AB C215 VCKYCY0JF105Z V 1 6.3V Ceramic AB C216 VCKYCY0JF105Z V 1 6.3V Ceramic AB
(VC-TA352W) C217 VCEA9M0JW107M V 100 6.3V Electrolytic AB C218 VCKYCY0JF105Z V 1 6.3V Ceramic AB C219 VCKYCY1CF104Z V 0.1 16V Ceramic AA C220 VCKYCY1CF104Z V 0.1 16V Ceramic AA C221 VCEA9M1CW106M V 10 16V Electrolytic AB C223 VCKYCY1CF104Z V 0.1 16V Ceramic AA C226 VCEA9M0JW107M V 100 6.3V Electrolytic AB
C227 VCKYCY0JF105Z V 1 6.3V Ceramic AB C228 VCEA9A0JW476M V 47 6.3V Electrolytic AB C251 VCEA9M1CW476M V 47 16V Electrolytic AB C252 VCEA0A0JW337M V 330 6.3V Electrolytic AC C256 VCKYCY1CF104Z V 0.1 16V Ceramic AA C301 VCEA9M0JW107M V 100 6.3V Electrolytic AB C302 VCKYCY0JF105Z V 1 6.3V Ceramic AB C303 VCKYCY1HB102K V 1000p 50V Ceramic AA C304 VCKYCY1HB102K V 1000p 50V Ceramic AA C305 VCKYCY1HB102K V 1000p 50V Ceramic AA C306 VCKYCY1HB102K V 1000p 50V Ceramic AA C311 VCKYCY1HF103Z V 0.01 50V Ceramic AA C312 VCKYCY1HF103Z V 0.01 50V Ceramic AA C315 VCKYCY1HB222K V 2200p 50V Ceramic AA C316 VCCCCY1HH180J V 18p 50V Ceramic AA C317 VCCCCY1HH120J V 12p 50V Ceramic AA C318 VCCCCY1HH120J V 12p 50V Ceramic AA C319 VCCCCY1HH100D V 10p 50V Ceramic AA C324 VCKYCY1HF103Z V 0.01 50V Ceramic AA C325 VCKYCY1HF103Z V 0.01 50V Ceramic AA C501 VCEA9M0JW107M V 100 6.3V Electrolytic AB C502 VCKYCY0JF105Z V 1 6.3V Ceramic AB C503 VCKYCY1CB104K V 0.1 16V Ceramic AB C504 VCEA9A1HW225M V 2.2 50V Electrolytic AB C505 VCKYCY1EB223K V 0.022 25V Ceramic AA C506 VCEA9M1HW474M V 0.47 50V Electrolytic AB C507 VCKYCY1CF104Z V 0.1 16V Ceramic AA C508 VCEA9M1HW475M V 4.7 50V Electrolytic AB C509 VCKYD41CY103N V 0.01 16V Ceramic AA C512 VCKYD41CY103N V 0.01 16V Ceramic AA C513 VCKYCY1HF103Z V 0.01 50V Ceramic AA C514 VCKYCY1HF103Z V 0.01 50V Ceramic AA C515 VCKYD41HB331K V 330p 50V Ceramic AA C516 VCCCCY1HH120J V 12p 50V Ceramic AA C517 VCEA9M1HW335M V 3.3 50V Electrolytic AB C518 VCKYCY1HF333Z V 0.033 50V Ceramic AA C519 VCEA9M1HW105M V 1 50V Electrolytic AB C521 VCCCCY1HH5R0C V 5p 50V Ceramic AA C523 VCKYCY1HF103Z V 0.01 50V Ceramic AA C601 VCEA9M0JW107M V 100 6.3V Electrolytic AB C602 VCKYCY1EB103K V 0.01 25V Ceramic AA C603 VCEA9M1CW106M V 10 16V Electrolytic AB C604 VCKYCY1HB821K V 820p 50V Ceramic AA C605 VCEA9M1CW106M V 10 16V Electrolytic AB C606 VCEA9M1HW475M V 4.7 50V Electrolytic AB C607 VCEA9M1HW475M V 4.7 50V Electrolytic AB C608 VCEA9M0JW226M V 22 6.3V Electrolytic AB C609 VCEA9M1HW475M V 4.7 50V Electrolytic AB C610 VCKYCY1CF104Z V 0.1 16V Ceramic AA C611 VCKYCY1CF104Z V 0.1 16V Ceramic AA C612 VCKYCY1CF104Z V 0.1 16V Ceramic AA
(VC-TA352W) C613 VCKYCY1HB822K V 8200p 50V Ceramic AB C617 VCEA9M1CW476M V 47 16V Electrolytic AB C618 VCKYCY1EB103K V 0.01 25V Ceramic AA C619 VCKYCY1EB103K V 0.01 25V Ceramic AA C620 VCEA9M1CW106M V 10 16V Electrolytic AB C621 VCQPYA2AA562J V 5600p 100V Mylar AC C622 VCKYCY1HB222K V 2200p 50V Ceramic AA C623 VCEA9M1CW106M V 10 16V Electrolytic AB C629 VCKYCY0JF105Z V 1 6.3V Ceramic AB C630 VCKYCY0JF105Z V 1 6.3V Ceramic AB C631 VCCCCY1HH101J V 100p 50V Ceramic AA C632 VCCCCY1HH101J V 100p 50V Ceramic AA C633 VCCCCY1HH221J V 220p 50V Ceramic AA C701 VCKYCY1HF103Z V 0.01 50V Ceramic AA C702 VCKYCY1HF103Z V 0.01 50V Ceramic AA C703 VCEA9M1HW105M V 1 50V Electrolytic AB C704 VCKYCY0JF105Z V 1 6.3V Ceramic AB C705 VCKYCY1HF103Z V 0.01 50V Ceramic AA C706 VCKYCY1HF103Z V 0.01 50V Ceramic AA C707 VCCCCY1HH150J V 15p 50V Ceramic AA C708 VCCCCY1HH150J V 15p 50V Ceramic AA C709 VCCCCY1HH180J V 18p 50V Ceramic AA C710 VCCCCY1HH180J V 18p 50V Ceramic AA
69
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
C711 VCKYCY1HB102K V 1000p 50V Ceramic AA C712 VCKYCY1HB102K V 1000p 50V Ceramic AA C713 VCKYCY1HB102K V 1000p 50V Ceramic AA C714 VCKYCY1CF104Z V 0.1 16V Ceramic AA C715 VCEA9M0JW226M V 22 6.3V Electrolytic AB C716 VCCCCY1HH221J V 220p 50V Ceramic AA C717 VCCCCY1HH221J V 220p 50V Ceramic AA C718 VCKYCY1CF104Z V 0.1 16V Ceramic AA C719 VCKYCY1EB103K V 0.01 25V Ceramic AA C722 VCKYCY1HF103Z V 0.01 50V Ceramic AA C723 VCKYCY1CF104Z V 0.1 16V Ceramic AA C724 VCKYCY1HF103Z V 0.01 50V Ceramic AA C725 VCKYCY1HF103Z V 0.01 50V Ceramic AA C727 VCKYCY1HF103Z V 0.01 50V Ceramic AA C729 VCKYCY1HF103Z V 0.01 50V Ceramic AA C730 VCKYCY1HF103Z V 0.01 50V Ceramic AA C736 VCKYCY1HF103Z V 0.01 50V Ceramic AA C737 VCKYCY1HF103Z V 0.01 50V Ceramic AA C738 VCKYCY1HB102K V 1000p 50V Ceramic AA C739 VCKYCY1HB102K V 1000p 50V Ceramic AA C743 VCKYCY1CF104Z V 0.1 16V Ceramic AA C744 VCEA2A0JW108M V 1000 6.3V Electrolytic AB C745 RC-EZ0380GEZZ J Capacitor AM C746 VCKYD41CY103N V 0.01 16V Ceramic AA C748 VCKYCY1HF103Z V 0.01 50V Ceramic AA C751 VCKYCY1HF103Z V 0.01 50V Ceramic AA C752 VCEA2A1VW107M V 100 35V Electrolytic AC C754 VCKYCY1EB223K V 0.022 25V Ceramic AA C755 VCKYCY1CB473K V 0.047 16V Ceramic AA C756 VCKYCY1CB473K V 0.047 16V Ceramic AA C759 VCEA9M0JW226M V 22 6.3V Electrolytic AB C760 VCEA9M0JW107M V 100 6.3V Electrolytic AB C763 VCEA9M0JW476M V 47 6.3V Electrolytic AB C764 VCKYCY1HF103Z V 0.01 50V Ceramic AA C770 VCCCCY1HH101J V 100p 50V Ceramic AA C771 VCE9EM1HW105M V 1 50V Elect.(N.P) AB C772 VCCCCY1HH120J V 12p 50V Ceramic AA C773 VCCCCY1HH120J V 12p 50V Ceramic AA C774 VCKYCY1CF104Z V 0.1 16V Ceramic AA C775 VCEA9M0JW107M V 100 6.3V Electrolytic AB C776 VCKYCY0JF105Z V 1 6.3V Ceramic AB C780 VCEA9M1CW107M V 100 16V Electrolytic AB C783 VCKYCY0JF105Z V 1 6.3V Ceramic AB C784 VCKYCY1HB102K V 1000p 50V Ceramic AA C785 VCEA9M0JW476M V 47 6.3V Electrolytic AB C786 VCKYCY1CF334Z V 0.33 16V Ceramic AA C787 VCFYFA1HA474J V 0.47 50V M.Polypro AC C789 VCKYCY1EB103K V 0.01 25V Ceramic AA C790 VCKYCY1HB392K V 3900p 50V Ceramic AA C791 VCKYCY1HB392K V 3900p 50V Ceramic AA C792 VCEA9M1CW476M V 47 16V Electrolytic AB C794 VCKYCY1EB223K V 0.022 25V Ceramic AA C795 VCKYCY1EB223K V 0.022 25V Ceramic AA C797 VCKYCY1CF104Z V 0.1 16V Ceramic AA C798 VCKYCY1EB223K V 0.022 25V Ceramic AA C799 VCKYD41CY103N V 0.01 16V Ceramic AA C801 VCKYCY1HF103Z V 0.01 50V Ceramic AA C802 VCEA9M0JW476M V 47 6.3V Electrolytic AB C803 VCKYCY1HF103Z V 0.01 50V Ceramic AA C804 VCEA9M0JW476M V 47 6.3V Electrolytic AB C805 VCKYCY1HF103Z V 0.01 50V Ceramic AA C806 VCKYCY1HF103Z V 0.01 50V Ceramic AA C811 VCEA9A1HW475M V 4.7 50V Electrolytic AB
å C902 RC-FZ028SCEZZ V Capacitor AD å C903 RC-KZ0105GEZZ J Capacitor AD å C904 RC-EZ0437GEZZ J Capacitor AK å C905 RC-EZ0661GEZZ J Capacitor AD å C906 VCFYAG2GA473K V 0.047 400V M.Polypro AD å C908 RC-KZ0112CEZZ V Capacitor AB å C909 VCQYTA1HM272J V 2700p 50V Mylar AA å C910 VCQYTA1HM152J V 1500p 50V Mylar AA å C911 VCEA9A1HW226M V 22 50V Electrolytic AB
C921 VCEA0A1AW477M V 470 10V Electrolytic AC C922 VCEA0A1HW476M V 47 50V Electrolytic AB C923 RC-EZ0438GEZZ J Capacitor AF
C924 VCEA0A0JW108M V 1000 6.3V Electrolytic AC C925 RC-EZ0439GEZZ J Capacitor AF C926 VCEA0A1EW107M V 100 25V Electrolytic AC C927 VCEA0A1VW477M V 470 35V Electrolytic AB C929 VCEA0A1JW476M V 47 63V Electrolytic AB C930 VCQYTA1HM103J V 0.01 50V Mylar AA C931 VCEA9M1HW105M V 1 50V Electrolytic AB C932 VCEA9M1HW105M V 1 50V Electrolytic AB C941 VCEA9A1CW476M V 47 16V Electrolytic AB C942 VCEA9M0JW476M V 47 6.3V Electrolytic AB C943 VCEA9M0JW226M V 22 6.3V Electrolytic AB C944 VCEA9M1CW476M V 47 16V Electrolytic AB C953 VCEA9M0JW226M V 22 6.3V Electrolytic AB C954 VCEA9M1HW105M V 1 50V Electrolytic AB C956 VCEA9M0JW226M V 22 6.3V Electrolytic AB C981 VCEA9M0JW476M V 47 6.3V Electrolytic AB C982 VCEA9M0JW226M V 22 6.3V Electrolytic AB C985 VCEA9M0JW476M V 47 6.3V Electrolytic AB C991 VCEA9M1CW476M V 47 16V Electrolytic AB C992 VCEA9M1CW226M V 22 16V Electrolytic AB
RESISTORS
R101 VRS-CY1JF470J V 47 1/16WMetal Oxide AA R103 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R104 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R105 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R108 VRS-CY1JF822J V 8.2k 1/16WMetal Oxide AA R110 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R111 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R112 VRS-CY1JF224J V 220k 1/16WMetal Oxide AA R113 VRD-RA2BE561J V 560 1/8W Carbon AA R201 VRS-CY1JF682J V 6.8k 1/16WMetal Oxide AA R202 VRS-CY1JF182J V 1.8k 1/16WMetal Oxide AA R203 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R207 VRS-CY1JF101J V 100 1/16W Metal Oxide AA R225 VRS-CY1JF750J V 75 1/16WMetal Oxide AA R226 VRS-CY1JF101J V 100 1/16W Metal Oxide AA R227 VRS-CY1JF750J V 75 1/16WMetal Oxide AA R228 VRS-CY1JF750J V 75 1/16WMetal Oxide AA
(VC-TA352W)
R229 VRS-CY1JF101J V 100 1/16W Metal Oxide AA
(VC-TA352W) R232 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R233 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R252 VRD-RA2EE331J V 330 1/4W Carbon AA R253 VRS-CY1JF101J V 100 1/16W Metal Oxide AA R254 VRS-CY1JF331J V 330 1/16W Metal Oxide AA R256 VRS-CY1JF472J V 4.7k 1/16WMetal Oxide AA R303 VRS-CY1JF392J V 3.9k 1/16WMetal Oxide AA R305 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R306 VRS-CY1JF561J V 560 1/16W Metal Oxide AA R309 VRS-CY1JF222J V 2.2k 1/16WMetal Oxide AA R311 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R317 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R330 VRS-CY1JF222J V 2.2k 1/16WMetal Oxide AA R331 VRD-RA2BE102J V 1k 1/8W Carbon AA R501 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R502 VRS-CY1JF273J V 27k 1/16W Metal Oxide AA R504 VRS-CY1JF221J V 220 1/16W Metal Oxide AA R505 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R507 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R513 VRD-RA2BE224J V 220k 1/8W Carbon AA R601 VRS-CY1JF822J V 8.2k 1/16WMetal Oxide AA R602 VRS-CY1JF274J V 270k 1/16WMetal Oxide AA R603 VRS-CY1JF221J V 220 1/16W Metal Oxide AA R604 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R605 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R606 VRS-CY1JF273J V 27k 1/16W Metal Oxide AA R607 VRS-CY1JF561J V 560 1/16W Metal Oxide AA R608 VRS-CY1JF472J V 4.7k 1/16WMetal Oxide AA R609 VRS-CY1JF562J V 5.6k 1/16WMetal Oxide AA R610 VRS-CY1JF182J V 1.8k 1/16WMetal Oxide AA R611 VRS-CY1JF393J V 39k 1/16W Metal Oxide AA R612 VRS-CY1JF123J V 12k 1/16W Metal Oxide AA
70
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
R613 VRS-CY1JF393J V 39k 1/16W Metal Oxide AA
(VC-TA352W)
R614 VRS-CY1JF123J V 12k 1/16W Metal Oxide AA
(VC-TA352W) R615 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R616 VRS-CY1JF103J V 10k 1/16W Metal Oxide AA R618 VRS-CY1JF563J V 56k 1/16W Metal Oxide AA R619 VRS-CY1JF470J V 47 1/16WMetal Oxide AA R620 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R621 VRD-RA2EE4R7J V 4.7 1/4W Carbon AA R623 VRS-CY1JF393J V 39k 1/16W Metal Oxide AA R624 VRS-CY1JF224J V 220k 1/16WMetal Oxide AA R627 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R629 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R630 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R631 VRS-CY1JF124J V 120k 1/16WMetal Oxide AA R632 VRS-CY1JF562J V 5.6k 1/16WMetal Oxide AA R633 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R634 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R635 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R636 VRS-CY1JF101J V 100 1/16W Metal Oxide AA R637 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R638 VRS-CY1JF683J V 68k 1/16W Metal Oxide AA R659 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R702 VRD-RA2BE102J V 1k 1/8W Carbon AA R703 VRD-RA2BE102J V 1k 1/8W Carbon AA R704 VRD-RA2BE102J V 1k 1/8W Carbon AA R705 VRD-RA2BE102J V 1k 1/8W Carbon AA R706 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R707 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA R708 VRD-RA2BE102J V 1k 1/8W Carbon AA R710 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R711 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R712 VRS-CY1JF223J V 22k 1/16W Metal Oxide AA R713 VRS-CY1JF564J V 560k 1/16WMetal Oxide AA R714 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R715 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R716 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R717 VRS-CY1JF331J V 330 1/16W Metal Oxide AA R718 VRS-CY1JF182J V 1.8k 1/16WMetal Oxide AA R719 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R720 VRS-CY1JF822J V 8.2k 1/16WMetal Oxide AA R722 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R723 VRS-CY1JF331J V 330 1/16W Metal Oxide AA R725 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R727 VRD-RA2EE151J V 150 1/4W Carbon AA R728 VRS-CY1JF182J V 1.8k 1/16WMetal Oxide AA R729 VRD-RA2BE154J V 150k 1/8W Carbon AA R731 VRS-CY1JF103J V 10k 1/16W Metal Oxide AA R732 VRS-CY1JF223J V 22k 1/16W Metal Oxide AA R734 VRD-RA2BE273J V 27k 1/8W Carbon AA R735 VRS-CY1JF563J V 56k 1/16W Metal Oxide AA R736 VRS-CY1JF103J V 10k 1/16W Metal Oxide AA R737 VRS-CY1JF222J V 2.2k 1/16WMetal Oxide AA R738 VRD-RA2BE104J V 100k 1/8W Carbon AA R739 VRD-RA2BE271J V 270 1/8W Carbon AA R740 VRD-RA2BE104J V 100k 1/8W Carbon AA R741 VRD-RA2BE271J V 270 1/8W Carbon AA R742 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R743 VRD-RA2BE391J V 390 1/8W Carbon AA R744 VRS-CY1JF473J V 47k 1/16W Metal Oxide AA R745 VRD-RA2BE391J V 390 1/8W Carbon AA R746 VRS-CY1JF103J V 10k 1/16W Metal Oxide AA R747 VRD-RA2EE151J V 150 1/4W Carbon AA R749 VRD-RM2HD271J V 270 1/2W Carbon AA R751 VRD-RA2BE123J V 12k 1/8W Carbon AA R752 VRD-RA2BE123J V 12k 1/8W Carbon AA R753 VRD-RA2BE102J V 1k 1/8W Carbon AA R756 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R758 VRD-RA2BE103J V 10k 1/8W Carbon AA R760 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R761 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R762 VRS-CY1JF123J V 12k 1/16W Metal Oxide AA R763 VRS-CY1JF563J V 56k 1/16W Metal Oxide AA R764 VRS-CY1JF183J V 18k 1/16W Metal Oxide AA
R765 VRS-CY1JF223J V 22k 1/16WMetal Oxide AA R766 VRS-CY1JF472J V 4.7k 1/16WMetal Oxide AA R768 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R770 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R771 VRD-RA2BE183J V 18k 1/8W Carbon AA R773 VRS-CY1JF222J V 2.2k 1/16WMetal Oxide AA R776 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R777 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R779 VRD-RA2BE103J V 10k 1/8W Carbon AA R780 VRD-RA2BE103J V 10k 1/8W Carbon AA R781 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R782 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R783 VRS-CY1JF392J V 3.9k 1/16WMetal Oxide AA R784 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R785 VRS-CY1JF105J V 1M 1/16WMetal Oxide AA R786 VRS-CY1JF564J V 560k 1/16WMetal Oxide AA R787 VRD-RM2HD1R0J V 1 1/2W Carbon AA R788 VRD-RM2HD1R0J V 1 1/2W Carbon AA R791 VRG-SC2EB1R0J V 1 1/4W Fuse ResistorAB R794 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R795 VRD-RA2BE225J V 2.2M 1/8W Carbon AA R796 VRD-RA2BE103J V 10k 1/8W Carbon AA R803 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R813 VRD-RA2BE183J V 18k 1/8W Carbon AA R814 VRS-CY1JF822J V 8.2k 1/16WMetal Oxide AA R815 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R821 VRS-CY1JF183J V 18k 1/16WMetal Oxide AA R822 VRS-CY1JF272J V 2.7k 1/16WMetal Oxide AA R823 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R824 VRS-CY1JF272J V 2.7k 1/16WMetal Oxide AA R825 VRS-CY1JF472J V 4.7k 1/16WMetal Oxide AA R826 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R827 VRD-RA2BE223J V 22k 1/8W Carbon AA R828 VRS-CY1JF563J V 56k 1/16WMetal Oxide AA R830 VRD-RA2EE100J V 10 1/4W Carbon AA R831 VRD-RA2BE101J V 100 1/8W Carbon AB R832 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R833 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R834 VRD-RA2BE103J V 10k 1/8W Carbon AA R835 VRD-RA2BE474J V 470k 1/8W Carbon AA R843 VRD-RA2BE474J V 470k 1/8W Carbon AA R855 VRS-CY1JF152J V 1.5k 1/16WMetal Oxide AA R862 VRD-RA2BE102J V 1k 1/8W Carbon AA R863 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R864 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R865 VRS-CY1JF471J V 470 1/16W Metal Oxide AA R866 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA
å R901 VRD-RA2HD105J V 1M 1/2W Carbon AA å R902 RR-HZ0014GEZZ J Resistor AE å R903 RR-WZ0017GEZZ J Resistor AD å R904 RR-SZ0006GEZZ J Resistor AD å R905 VRD-RM2HD105J V 1M 1/2W Carbon AA å R906 VRD-RM2HD273J V 27k 1/2W Carbon AA å R907 VRS-CY1JF563J V 56k 1/16W Metal Oxide AA å R908 VRN-VV3DBR56J V 0.56 2W Metal Film AA å R910 VRD-RM2HD152J V 1.5k 1/2W Carbon AA å R911 VRS-CY1JF333J V 33k 1/16W Metal Oxide AA å R912 VRS-CY1JF153J V 15k 1/16W Metal Oxide AA å R913 VRD-RM2HD101J V 100 1/2W Carbon AA å R914 VRS-CY1JF183J V 18k 1/16W Metal Oxide AA å R915 VRD-RM2HD105J V 1M 1/2W Carbon AA
R921 VRS-CY1JF1R0J V 1 1/16W Metal Oxide AA R922 VRS-CY1JF100J V 10 1/16WMetal Oxide AA R923 VRS-CY1JF273J V 27k 1/16WMetal Oxide AA R924 VRS-CY1JF104J V 100k 1/16WMetal Oxide AA R925 VRS-CY1JF101J V 100 1/16W Metal Oxide AA R926 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R927 VRS-CY1JF561J V 560 1/16W Metal Oxide AA R928 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R929 VRD-RA2BE471J V 470 1/8W Carbon AA R930 VRS-CY1JF122J V 1.2k 1/16WMetal Oxide AA R931 VRS-CY1JF152J V 1.5k 1/16WMetal Oxide AA R932 VRD-RA2BE152J V 1.5k 1/8W Carbon AA R940 VRD-RM2HD471J V 470 1/2W Carbon AA R941 VRS-CY1JF333J V 33k 1/16WMetal Oxide AA
71
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
R942 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R943 VRD-RM2HD561J V 560 1/2W Carbon AA R944 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R945 VRS-CY1JF473J V 47k 1/16WMetal Oxide AA R946 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R947 VRS-CY1JF821J V 820 1/16W Metal Oxide AA R948 VRS-CY1JF332J V 3.3k 1/16WMetal Oxide AA R949 VRD-RA2BE103J V 10k 1/8W Carbon AA R950 VRD-RA2BE223J V 22k 1/8W Carbon AA R951 VRS-CY1JF223J V 22k 1/16WMetal Oxide AA R952 VRS-CY1JF223J V 22k 1/16WMetal Oxide AA R954 VRS-CY1JF561J V 560 1/16W Metal Oxide AA R955 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R956 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R957 VRS-CY1JF152J V 1.5k 1/16WMetal Oxide AA R963 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R964 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R965 VRS-CY1JF223J V 22k 1/16WMetal Oxide AA R981 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R982 VRS-CY1JF561J V 560 1/16W Metal Oxide AA R984 VRS-CY1JF102J V 1k 1/16W Metal Oxide AA R985 VRS-CY1JF000J V 00 1/16WMetal Oxide AA R988 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R991 VRD-RA2BE331J V 330 1/8W Carbon AA R992 VRS-CY1JF222J V 2.2k 1/16WMetal Oxide AA R993 VRS-CY1JF103J V 10k 1/16WMetal Oxide AA R7704 VRS-CY1JF473J V 47k 1/16WMetal Oxide AA R7705 VRS-CY1JF154J V 150k 1/16W Metal Oxide AA R7706 VRS-CY1JF822J V 8.2k 1/16W Metal Oxide AA R7707 VRS-CY1JF104J V 100k 1/16W Metal Oxide AA RJ100 VRS-CY1JF000J V 00 1/16W Metal Oxide AA RJ104 VRS-CY1JF000J V 00 1/16W Metal Oxide AA RJ201 VRS-CY1JF000J V 00 1/16W Metal Oxide AA RJ202 VRS-CY1JF000J V 00 1/16W Metal Oxide AA RJ206 VRS-CY1JF000J V 00 1/16W Metal Oxide AA
(VC-TA352W)
MISCELLANEOUS PARTS
å ACC901 QACCB5005AJZZ V AC Cord AY
(VC-TA351W,TA352W)
å ACC901 QACCV2009AJZZ V AC Cord AM
(VC-AT350, TA351A/K/M, TA355, TA356)
å ACC901 QACCZ3009AJZZ V AC Cord AP
(VC-TA351B/S)
å F901 QFS-C2025CEZZ V Fuse, T2AL/250V AD
FB101 RBLN-0043CEZZ V Ferrite Bead AB FB201 RBLN-0036CEZZ V Ferrite Bead AB FB202 RBLN-0036CEZZ V Ferrite Bead AB FB203 RBLN-0036CEZZ V Ferrite Bead AB FB701 RBLN-0036CEZZ V Ferrite Bead AB
å FB904 RBLN-0036CEZZ V Ferrite Bead AB
FB905 RBLN-0036CEZZ V Ferrite Bead AB
å FH901 QFSHD1013CEZZ V Fuse Holder AC å FH902 QFSHD1014CEZZ V Fuse Holder AC
J201 QJAKH0011AJZZ V Jack AK J202 QJAKF0065AJZZ V Jack AG
(VC-TA352W)
P101 QPLGN0447REZZ V Plug, AA
(Ecxcept for VC-TA351W) P201 QPLGN0447REZZ V Plug, 4pin(TP201-4) AA P701 QPLGZ0883GEZZ J Plug, 8pin(AC) AD P803 QPLGZ0360GEZZ J Plug, 3pin(AE) AB
å P901 QPLGN0269GEZZ J Plug, 3pin(AP) AB
RMC801 RRMCU0002AJZZ V Remote Receiver AH S701 QSW-F0042AJZZ V Rec Tip Switch AG S702 QSW-F0043GEZZ J Switch AD S703 QSW-K0098GEZZ J Switch AF S807 QSW-K0086GEZZ J Switch, CH - AC S808 QSW-K0086GEZZ J Switch, MENU AC S809 QSW-K0086GEZZ J Switch, SET AC S810 QSW-K0086GEZZ J Switch, CH + AC S811 QSW-K0086GEZZ J Switch, EJECT AC S813 QSW-K0086GEZZ J Switch, POWER AC SC301 QSOCN0464REZZ V Socket, 4pin(AH) AC
SC601 QSOCN0604REN1 V Socket, 6pin(AA) AB SC602 QSOCZ0293GEZZ J Socket, 2pin(AE) AC SC701 QSOCN0704REN1 V Socket, 7pin(AD) AB SC702 QSOCZ0292GEZZ J Socket, 2pin(AL) AC SC801 QSOCZ0625CEZZ V Socket, 6pin(AO) AC
DUNTK5942TEV2 OPERATION Unit
RESISTORS
R882 VRS-CY1JF472J V 4.7k 1/16WMetal Oxide AA R883 VRS-CY1JF822J V 8.2k 1/16WMetal Oxide AA R884 VRS-CY1JF103J V 10k 1/16W Metal Oxide AA R885 VRS-CY1JF223J V 22k 1/16W Metal Oxide AA
MISCELLANEOUS PARTS
P881 QPLGZ0626CEZZ J Plug, 6pin(OA) AF S881 QSW-Z0001AJZZ V Switch AQ S882 QSW-K0086GEZZ J Switch AC S883 QSW-K0086GEZZ J Switch AC S884 QSW-K0086GEZZ J Switch AC S886 QSW-K0086GEZZ J Switch AC
DUNTK5977TEV1
LED Unit
DIODES
D851 RH-PX0300GEZZ J Photodiode AD
MISCELLANEOUS PARTS
SC851 QSOCZ0360GEZZ J Socket AC
MECHANISM CHASSIS PARTS
1 LBNDK1011AJZZ V Tension Band Ass’y AH 2 LBOSZ1007AJZZ V Tension Arm boss AD 3 LBOSZ1006AJZZ V Cassette Stay L AD 5 LCHSM0174AJZZ V Main Chassis Ass’y AV 6 LHLDZ2016AJZZ V Loading Motor Block AG 7 LPOLM0070GEZZ J Supply Pole Base Ass’y AK 8 LPOLM0064GEZZ J Take-Up Pole Base Ass’y AM 9 MLEVF0518AJZZ V Take-Up Loading Arm Ass’yAF 10 MLEVF0519AJZZ V Supply LoadingArm Ass’y AF 11 MLEVF0499AJZZ V Pinch Drive Lever Ass’y AG 12 MLEVF0500GEZZ J Pinch Roller Lever Ass’y AW 15 MLEVF0523AJZZ V Tension Arm Ass’y AH 16 LANGF9620AJFW V A/C Head Plate AG 17 MLEVP0271AJZZ V Sifter Drive Lever AE 18 MLEVP0272AJZZ V Pinch Double Action LeverAD 19 MLEVP0301AJZZ V Reverse Guide Lever Ass’yAL 20 MLEVP0275AJZZ V Reverse Drive Lever AD 21 MLEVP0292AJZZ V Slow Brake Lever AE 22 MLEVP0290AJZZ V Open Lever AD
or 22 MLEVP0036AJZZ V Open Lever 23 MLEVP0293AJZZ V Clutch Lever AE 24 MLEVP0324AJZZ V Supply Main Brake Ass’y AF 25 MLEVP0325AJZZ V Take-Up Main Brake Ass’y AF 27 MSLiP0010AJZZ V Sifter AH
or 27 MSLiP0015AJZZ V Sifter AH 29 MSPRD0175AJFJ V Reverse Guide Spring 2 AE 30 MSPRT0402AJFJ V Loading Double Action AE
Spring 31 MSPRT0403AJFJ V Pinch Double Action SpringAD 32 MSPRC0213AJFJ V Earth Spring AC 33 MSPRT0416AJFJ V Tension Spring AD 34 NBLTK0067AJ00 V Reel Belt AE
72
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
35 NDAiV1078AJ00 V Reel Disk AE
or 35 NDAiV1091AJ00 V Reel Disk AE 36 NGERH1293AJZZ V Loading Connect Gear AD 37 NGERH1295AJ00 V Master Cam AE 38 NGERH1294AJZZ V Casecon Drive Gear AD 39 NGERH1270AJZZ V Take-Up Loading Gear AF 40 NGERH1271AJZZ V Supply Loading Gear AD 41 NGERH1272AJZZ V Pinch Drive Cam AE 43 NGERH1299AJZZ V Reel Relay Gear AE 44 NGERW1070AJZZ V Worm Gear AD 45 NGERW1066AJZZ V Worm Wheel Gear AD 46 NiDR-0018AJZZ V Idler Wheel Ass’y AK 47 NPLYV0162AJZZ V Motor Pulley AD 48 NPLYV0163AJZZ V Limitter Pulley Ass’y AM 49 NROLP0131GEZZ J Guide Roller AL 50 NSFTP0032AJZZ V Tension Pole Adjuster AB 51 MSPRC0217AJFJ V Guide Roller Spring AC 52 PREFL1011AJZZ V Light Guide AE 53 QCNW-8022AJZZ V FFC for Drum Motor AF 55 QCNW-8021AJZZ V FFC for A/C Head AF 56 QPWBF5243AJZZ V A/C Head PWB AE 57 QSOCN0605REN1 V Socket, 6 pin AB 58 RHEDT0036AJZZ V Full Erase Head AM 59 RHEDU0088GEZZ J A/C Head Ass’y AV 60 RMOTM1078GEZZ J Loading Motor AP 61 RMOTN2067GEZZ J Capstan Motor AY 62 RMOTP1151GEZZ J Drum Drive Motor AT 63 DDRMW0028TEX1 V Upper and lower drum BP
Ass’y(VC-TA351/TA351W/ TA352/TA356)
63 DDRMW0028TEX2 V Upper and lower drum BT
Ass’y(VC-TA350/TA355) 65 QBRSK0041GEZZ J Drum Earth Brush AD 66 XBPSD26P05J00 V Drum Drive Motor MountingAA
Screw (SW2.6P+5S) 67 PGIDC0056GEFW J Drum Base AL 68 QPWBF5468AJZZ V PWB(LDG Motor) AE 69 QPLGZ0292GEZZ J Socket(LDG Motor) AE 70 MSPRC0223AJFJ V Azimuth Spring AC 71 MSPRC0224AJFJ V Height Adjusting spring AC
SCREW, NUTS AND WASHERS
201 XBPSD26P08000 J Screw 2.6P+8S A/C Head AA 202 LX-HZ3082GEZZ J WSW2.6+6 (AC) AD 203 XJPSD26P06000 J Screw, 2.6P+6S”(B Tite) AA
(For Capstan Motor PWM)
207 XHPSD30P08WS0 J Screw, C3.0P+8S” AA
(For Drum Base)
208 XRESJ30-06000 J E-Ring, E-3” AA 209 XWHJZ31-03052 J Washer, W3.1-5.2-0.3” AC 210 XWHJZ31-04052 J Washer, W3.1-5.2-0.4” AC 211 XWHJZ31-05052 J Washer, W3.1-5.2-0.5” AC 212 XWHJZ31-06052 J Washer, W3.1-5.2-0.6” AC 213 XWHJZ31-07052 J Washer, W3.1-5.2-0.7” AC 214 PSPAP0009GEZZ J Reverse Guide AA
Adjusting Nut
216 LX-WZ1041GE00 J CW 2.6-6-0.5 CAM AA 218 XBPSD30P06J00 J Drum Base Mounting AA
Screw (SW 3P+6S)
220 LX-BZ3096GEFD J Tilt Adjusting Screw AA 221 XBPSD26P06000 J Azimuth Adjusting Screw AA
2.6+6S 222 LX-BZ3197GEFD J Screw (A/C Head) AD 223 XWHJZ31-08052 J Washer, W3.1-5.2-0.8” AC
CASSETTE HOUSING CONTROL PARTS
300 CHLDX3081GE02 J Cassette Housing AX
301 LANGF9592GEFW J Upper Plate AL 302 LHLDX1028GE00 J Frame (L) AH 303 LHLDX1032GE00 J Frame (R) AH 304 LHLDX1030GEZZ J Holder (L) AE 305 LHLDX1031GEZZ J Holder (R) AE 306 MLEVF0469GEFW J Proof Lever (R) AE 307 MLEVP0281GE00 J Door Open Lever AD 308 MSLiF0076GEFW J Slider AH 309 MSPRD0151GEFJ J Proof Lever (R) Spring AB 310 MSPRD0166GEFJ J Drive Gear (R) Spring AE 311 MSPRP0159GEFJ J Cassette Spring AD 312 MSPRT0381GEFJ J Double Action Spring AB 313 NGERH1278GEZZ J Drive Gear L AE 314 NGERH1309GEZZ J Drive Gear R AE 315 NGERR1008GE00 J Double Action Rack Gear AE 316 NGERR3005GEFW J Drive Angle Gear AG 317 NSFTD0041GEFD J Main Shaft AF
Control Ass’y
MECHANICAL PARTS
600 GCABA3131AJSA V Top Cabinet AR 600 GCABA3131AJSG V Top Cabinet AR 601 GCABB1223AJSF V Main Frame AN 601 GCABB1223AJSC V Main Frame AN 602 GCOVA2143AJZZ V Antenna Terminal Cover AD
603 PSLDM4566AJFW V Shield Angle AD 604 XHPSD26P06WS0 V Screw AA 605 XHPSD30P06WS0 V Screw(CHASS.) AA 606 LANGK0197AJFW V Top Cabinet Fixing Angle AG 607 XEPSD30P14XS0 V Screw(Mecha) AB 608 LX-HZ3047GEFF J Screw(Top Cab.) AA 609 XEBSD30P12000 V Screw(Top Cab/PNL) AA 610 LX-HZ3087GEFN J Screw(Main Frame) AB 611 PSLDM4575AJFW V H/A Shield AD 612 LHLDZ1962AJ00 V Sensor LED Hplder AD 613 PGUMS0026AJZZ V Foot Rubber AB 614 TLABM4342AJZZ V Model Label (VC-TA350) AC 614 TLABM4327AJZZ V Model Label 614 TLABM4328AJZZ V Model Label (VC-TA351B)AC 614 TLABM4331AJZZ V Model Label (VC-TA351K)AC 614 TLABM4329AJZZ V Model Label (VC-TA351S)AC 614 TLABM4332AJZZ V Model Label 614 TLABM4422AJZZ V Model Label 614 TLABM4348AJZZ V Model Label (VC-TA355) AC 614 TLABM4333AJZZ V Model Label (VC-TA356) AC 615 XJPSD30P10WS0 V Screw(ANT. Cov.) AA
(Except for VC-TA355, TA356) (VC-TA355, TA356) (Except for VC-TA355, TA356) (VC-TA355, TA356)
(VC-TA351A/M)AC
(VC-TA351W) (VC-TA352W) AC
AC
FRONT PANEL PARTS
500 CPNLC2830TEV1 V Front Panel Ass’y AW 500 CPNLC2827TEV1 V Front Panel Ass’y AW 500 CPNLC2869TEV1 V Front Panel Ass’y AW 500 CPNLC2831TEV1 V Front Panel Ass’y AW 500 CPNLC2828TEV1 V Front Panel Ass’y AW 500-2 HBDGB1010AJSA V SHARP Badge AG
500-3 HDECQ2095AJSA V Cassette Flap (VC-TA350)AL 500-3 HDECQ2253AJSA V Cassette Flap AL
500-3 HDECQ2297AJSA V Cassette Flap AL
(VC-TA350) (VC-TA351/TA351W) (VC-TA352W) (VC-TA355) (VC-TA356)
(VC-TA351/TA351W) (VC-TA352W)
73
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
500-3 HDECQ2284AJSA V Cassette Flap (VC-TA355)AL 500-3 HDECQ2285AJSA V Cassette Flap (VC-TA356)AL 500-4 HDECQ2098AJSC V Window Dec. AK 500-5 JBTN-2979AJSA V Button, REC AC
(Except for VC-TA355, TA356)
500-5 JBTN-2979AJSG V Button, REC (VC-TA355, AC
TA356) 500-6 JBTN-2939AJSA V Button, Set Up AF 500-7 MSPRD0103AJFJ V Cassette Spring AB 500-8 HiNDP2103AJSA V Low Power Dec. AC 502 CBTN-2869TEV2 V Play Button Ass’y AL
(Except for VC-TA355, TA356) 502 CBTN-2869TEV5 V Play Button Ass’y AL
(VC-TA355, TA356) 502-1 JBTN-2869AJSA V Play Button AL
(Except for VC-TA355, TA356) 502-1 JBTN-2869AJSG V Play Button AL
(VC-TA355, TA356) 502-2 LHLDZ2021AJZZ V Button Holder AE 502-3 JKNBK1106AJSA V Knob AG
(Except for VC-TA355, TA356) 502-3 JKNBK1106AJSG V Knob AG
(VC-TA355, TA356) 503 TLABZ1681AJZZ V Feature Label AE
SUPPLIED ACCESSORIES
ACCESSORIES
QCNW-0323AJZZ V 75 ohm Coaxial Cable AK TiNS-3883AJZZ V Operation Manual
(VC-TA350)
TiNS-3885AJZZ V Operation Manual AN
(VC-TA351A/B/K/M, TA351W,
TA356)
TiNS-3886AJZZ V Operation Manual AL
(VC-TA351S)
TiNS-3903AJZZ V Operation Manual
(VC-TA352W)
RRMCG1208AJSA V Infrared Remote Control AS
Unit (VC-TA350)
RRMCG1274AJSA V Infrared Remote Control AV
Unit (VC-TA351/TA351W)
RRMCG1205AJSA V Infrared Remote Control AV
Unit (VC-TA352W)
RRMCG1274AJSA V Infrared Remote Control AV
Unit (VC-TA356)
QPLGA0013GEZZ V AC Plug Adaptor AH
Unit (VC-TA351S)
SPAKX1057AJZZ - Buffrer Material
(VC-TA351W, TA352W)
SPAKX1073AJZZ - Buffrer Material
(Except for VC-TA351W, VC-TA352W)
TMAPC0041AJZZ - Circuit Diagram
(VC-TA351K) SPAKP0114AJZZ - Foam Bag — TLABV0182AJZZ - Bar Code Label
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC4431AJZZ - Packing Case (VC-TA350) — SPAKC4418AJZZ - Packing Case
(VC-TA351A)
SPAKC4505AJZZ - Packing Case
(VC-TA351B)
SPAKC4420AJZZ - Packing Case
(VC-TA351K)
SPAKC4504AJZZ - Packing Case
(VC-TA351M)
SPAKC4502AJZZ - Packing Case
(VC-TA351S)
SPAKC4421AJZZ - Packing Case
(VC-TA351W)
SPAKC4520AJZZ - Packing Case
(VC-TA352W)
SPAKC4435AJZZ - Packing Case
(VC-TA355)
SPAKC4422AJZZ - Packing Case
(VC-TA356)
74
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
11. EXPLODED VIEW
MECHANISM CHASSIS EXPLODED VIEW
H
66
62
66
G
50
62
63
207
F
1
15
E
33
66
66
65
67
218
58
25
53
222
202
70
221
59
201
202
207
49
51
220
55
57
56
202
16
71
49
51
8
22
32
31
52
2
24
4
7
D
35
35
209 210 211 212 213 223
C
46
43
B
27
43
23
10
30
40
48
9
39
30
45
219
11
36
6
214
12
19
203
5
37
208
44
47
216
18
29
41
21
38
17
60
20
61
34
68
A
69
75
7654321
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
H
CASSETTE HOUSING CONTROL EXPLODED VIEW
300
G
301
F
304
302
311
311
E
305
306
308
309
313
D
310
317
C
303
314
312
B
307
315
316
A
7654321
76
VC-TA350/TA351/351W
A
611
B
C
C
B
600
609
615
602
612
605
604
603
607
608
610
614
606
601
613
A
605
609
VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
MECHANICAL EXPLODED VIEW
H
G
F
E
D
C
B
A
7654321
77
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
C
FRONT PANEL EXPLODED VIEW
500-7
500-3
500
D
500-1
500-2
500-6
E
500-8
F
500-4
503
G
H
123456
PRECAUTION ON FRONT PANEL SET-UP
Cassette cover open lever
Cassette housing
Before attaching the front panel in position, make sure that the cassette cover open lever is in its right place (lower-most). If it is out of position, push it down with a finger.
Cassette cover open lever
Keep the cassette over about 45° open and make sure that the cassette cover open le­ver is between the front panel and the cassette cover. Now fix the front panel in place.
502-1
About 45°
502-2
Front panel
Cassette cover
Cassette cover open lever
Do not mount the front panel with the cassette cover tilted too open. Otherwise the cassette cover might wrongly run on the cassette housing.
502
502-3
500-5
Cassette cover
1
5
Removing the cassette compartment cover. 1 Open the cassette compartment cover
fully. 2 Remove the center positioner. 3 Slide the cover to the right. 4 Slightly bend the cover. 5 Draw out the left-side rod.
3
4
2
78
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
12. PACKING OF THE SET
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
Accessories
TiNS-3883AJZZ Operation Manual (VC-TA350) TiNS-3885AJZZ Operation Manual (VC-TA351A/B/K/M,
TiNS-3886AJZZ (Operation Manual VC-TA351S) TiNS-3903AJZZ Operation Manual (VC-TA352W) QPLGA0013GEZZ AC Plug Adaptor (VC-TA351S)
TMAPC0041AJZZ Circuit Diagram (VC-TA351K)
RRMCG1208AJSA (VC-TA350) RRMCG1274AJSA (VC-TA351/TA351W) RRMCG1205AJSA (VC-TA352W) RRMCG1274AJSA (VC-TA356) Infrared Remote Control Unit
TA351W, TA356)
Dry Battery
QCNW-0323AJZZ
75 ohm Coaxial Cable
SPAKX1057AJZZ
(VC-TA351W, TA352W)
SPAKX1073AJZZ
(Except for VC-TA351W,TA352W)
Packing Foam
TLABV0182AJZZ Bar Code Label
MARK Not Replacement Item
SPAKC4418AJZZ (VC-TA351A)SPAKC4505AJZZ (VC-TA351B)SPAKC4420AJZZ (VC-TA351K)SPAKC4504AJZZ (VC-TA351M)SPAKC4502AJZZ (VC-TA351S)SPAKC4421AJZZ (VC-TA351W)SPAKC4520AJZZ (VC-TA352W)SPAKC4435AJZZ (VC-TA355)SPAKC4422AJZZ (VC-TA356)
Packing Case
79
VC-TA350/TA351/351W VC-TA352W/TA355/TA356
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
TQ0949-S
July. 2000 Printed in Japan
S.A KY
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
80
Loading...