Sharp VC-MH714HM, VC-MH704HM, VC-MH704LM Operation Manual

● AUTO INSTALLATION

● SHARP SUPER PICTURE

● NICAM Hi-Fi STEREO

● 6 HEAD EXTENDED PLAY

● CHILD LOCK

VC-MH714HM
VC-MH704HM

VC-MH704LM

VIDEO CASSETTE RECORDER

OPERATION MANUAL

VC-MH704HM Shown

TINS-3992UMZZ HM Final Cover 12/9/01 10:07 am Page 1

SAFETY WARNINGS

Observe all warnings for your safety and to ensure trouble free use
of your VCR.

INFORMATION

Additional information complements instructions.

Dear SHARP Customer

Thank you for buying this SHARP VCR. Given proper care it will provide years of
entertainment for the whole family. Please read this operation manual carefully before
attempting to operate the VCR.

Copyright

● Audio-visual material may consist of copyrighted works which must not be recorded

without the authority of the owner of the copyright. Please refer to the relevant laws in
your country.

● No part of this publication may be reproduced, stored or transmitted in any form without

prior permission from SHARP Electronics (UK) Ltd.

●

®

and PlusCode®are registered trademarks of Gemstar Development

Corporation.

● system is manufactured under license from Gemstar Development Corporation.

This manual covers a range of models, not all of the features
included will be relevant to your VCR.

If you require any advice or assistance regarding your Sharp
product, please visit our web-site www.sharp.co.uk/support.
Customers without Internet access may telephone
08705 274277 during office hours (or [phone] if
telephoning from Ireland).

(i)

TINS-3992UMZZ HM Final Cover 12/9/01 10:07 am Page 2

VCR REMOTE CONTROL

VCR FRONT PANEL/REMOTE CONTROL EQUIVALENT FUNCTIONS.

If you prefer, or if remote control batteries fail, you will need to use the VCR front panel controls. The only
differences in function are shown below:

FUNCTION OSD

On-Screen Display
Moving UP/DOWN menu
Moving LEFT/RIGHT menu

OPERATION WITH REMOTE

CONTROL

[ / ] Menu Select buttons
[ / ] Menu Select buttons

OPERATION WITH VCR

FRONT PANEL

CHANNEL / buttons.

Press the FF or REW buttons

on the front of the VCR.

/

(ii)

2. CHILD LOCK

20. MODE ON SCREEN

DISPLAY

18. MENU SELECT

/ / /

26. PAUSE/STILL

8. AM/PM or

25. PLAY/X2

21. DISPLAY

4. AUDIO OUT

9. REWIND

24. FAST FORWARD

12.SLOW

13. TAPE SPEED

27. DPSS

SLOW SPEED

/

+

7. NUMBER

BUTTONS

17. SET

19. CLEAR

10. STOP

(The STOP button is

also used to switch on the VCR.)

16. SKIP SEARCH

1. STANDBY

3. TIMER ON/OFF

6. SV/V+/TIMER or

PLUSCODE if you
have a VC-MH714HM

23. INPUT SELECT

28. TV/VCR

/

14. BASIC SHARP TV

CONTROLS

11. RECORD

22. CHANNEL UP AND

DOWN

5. MENU

15. ZERO BACK

TINS-3992UMZZ HM Final Cover 12/9/01 10:07 am Page 3

SHARP ELECTRONICS (U.K.) Ltd.

TINS-3992UMN1

Printed in U.K.

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC

as amended by 93/68/EEC.

• Specifications are subject to change without notice as part of our policy of continuous
improvement.

• No liability is accepted for any inaccuracies or omissions in this publication, although
every possible care has been taken to make it complete and as accurate as possible.

CALLING FOR SERVICE

SHARP Customer Helpline: Tel: [phone] during office hours
(or [phone] if telephoning from Ireland)

● If you are unable to resolve a problem using the TROUBLESHOOTING guide, do not

remove the cabinet or attempt to service this VCR yourself.

● For service please contact your dealer. If this is not possible, please call our Customer

Information Centre for details of your nearest Sharp Service Centre.

● In the unlikely event of this equipment requiring repair during the guarantee period, you

will need to provide proof of the date of purchase to the repairing company. Please keep
your invoice or receipt which is supplied at the time of purchase.

● Certain replacement parts and accessories may be obtained from our main parts

distributor who can be contacted at: Willow Vale Electronics Limited
Tel. [phone]. Most credit/debit cards accepted.

Alternatively, please visit our web-site:
www.sharp.co.uk/support

100% of the pulp used

in making this paper comes

from sustainable forests

TINS-3992UMZZ HM Final Cover 12/9/01 10:07 am Page 4

1

BEFORE USING YOUR VCR

Important notes on your VCR ....................................................................................................... 2

Unpacking the accessories........................................................................................................... 3

INSTALLING YOUR VCR

Connecting the cables ................................................................................................................. 4

Auto Tuning ..................................................................................................................................... 5

BASIC OPERATION

Scart lead connection (Not supplied)......................................................................................... 9

Important notes on your VCR and video tapes ......................................................................... 9

How to playback a video tape....................................................................................................9

Pausing and slow motion...................................................................................... 10

Fast forwarding/rewinding a video tape............................................................ 11

Immediate recording................................................................................................................... 11

Tape speed selection ........................................................................................... 12

How to use to make a recording (vc-mh714hm only)............................................ 13

How to set a delayed recording ................................................................................................ 15

ADVANCED OPERATION

Audio and your VCR.................................................................................................................... 18

Playback of a video tape ........................................................................................................... 20

Checking the amount of tape remaining.......................................................... 20

Playing back a video tape repeatedly .............................................................. 20

LCD Display ................................................................................................................................... 21

Tape counter and zero back......................................................................................................21

Blue mute ...................................................................................................................................... 22

Colour ............................................................................................................................................ 22

Searching the video tape ........................................................................................................... 23

Skip searching the video tape............................................................................. 23

Digital programme search system (DPSS) .......................................................... 23

Recording from other equipment .............................................................................................. 24

Child lock ...................................................................................................................................... 25

Decoder switching operation.....................................................................................................26

CUSTOMISED INSTALLATION

Manually tuning a channel......................................................................................................... 27

Manually sorting channels .......................................................................................................... 28

Sorting the channels into your preferred order.................................................. 28

Deleting channels ................................................................................................. 29

Manually setting the clock.......................................................................................................... 30

MORE INFORMATION ABOUT YOUR VCR

VCR display................................................................................................................................... 31

Selecting the output from the VCR............................................................................................ 31

On-screen display ........................................................................................................................ 32

Specifications................................................................................................................................ 33

Troubleshooting ............................................................................................................................ 34

VCR reset....................................................................................................................................... 36

RF channel tuning ........................................................................................................................ 36

Guarantee .................................................................................................................................... 37

Connecting to the mains ............................................................................................................ 38

Calling for service .........................................................................................................Back cover

CONTENTS

TINS-3992UMZZ English.book Page 1 Wednesday, May 9, 2001 12:25 PM

2

www.sharp.co.uk/support

BEFORE USING YOUR VCR

IMPORTANT NOTES ON YOUR VCR

IDEAL VCR LOCATION

PLACE THE VCR..

• ... on a flat level surface away from radiators
or other heat sources and out of direct
sunlight.

• ... and video tapes away from magnetic
sources such as speakers or microwave ovens.

• ... at least 8” (20cm) away from the TV.

• ... away from curtains, carpets or other
materials and allow ventilation space around
the VCR.

DO NOT...

• ... block the air-vent openings.

• ... expose the VCR to excessive dust,
mechanical vibration or shock.

• ... place any heavy object or liquid on top of
the VCR. If liquid drops inside the VCR unplug
immediately and contact your SHARP dealer.
Do not use the VCR.

• ... insert or drop anything into the tape
compartment or through the
air-vents, as this could result in serious
damage, fire or an electric shock.

POWER SOCKETS

• To avoid overheating or even fire, insert the
plug correctly into the socket.

DO NOT...

• ... overload power sockets, this may cause a
fire or electric shock.

• ... pull the power cord to disconnect the plug
from the mains.

• ... bind the power cords together.

• This VCR is not equipped with a mains power
switch. Accordingly, nominal current to drive
the clock is drawn at all times when the AC
power cord is plugged into a wall socket. If
the VCR is not to be used for an extended
period be sure to unplug the cord.

TINS-3992UMZZ English.book Page 2 Wednesday, May 9, 2001 12:25 PM

3

www.sharp.co.uk/support

BEFORE USING YOUR VCR

UNPACKING THE ACCESSORIES

To fit the batteries into the remote control

Remove the battery cover on the back of the remote control.
Fit the batteries: to and to terminals. Place the

battery cover back into position.

CHECK ALL THESE ACCESSORIES ARE SUPPLIED WITH YOUR VCR. CONTACT YOUR DEALER IF
ANY ARE MISSING.

(TYPE AA/R6/UM3)
BATTERIES (X2)

for the remote control unit.

RF CONNECTION CABLE

connects the VCR to the TV.

Remote Control

• Remote Control must be pointed towards the VCR to operate.

• Do not expose to liquid or shock.

• May not function if the VCR is in direct sunlight or any other strong light.

• Replace both alkaline batteries (type AA/R6/UM3) if the remote control
fails.

• Remove the batteries and keep in a safe place if you do not plan to use
the VCR for several months.

• Remove and dispose of flat batteries safely and promptly.

• Incorrect use of batteries may cause them to leak or burst.

Battery cover

REMOTE

CONTROL

For a more

detailed

picture of

your remote

control refer

to page (ii).

TINS-3992UMZZ English.book Page 3 Wednesday, May 9, 2001 12:25 PM

4

SHARP Helpline tel: [phone]

or www.sharp.co.uk/support

INSTALLING YOUR VCR

CONNECTING THE CABLES

✔

The VCR is correctly connected.

EXISTING AERIAL
OR CATV CABLE

Optional:

Connect your
Satellite receiver or decoder to
the VCR using a scart lead to

LINE 2 IN/DECODER

socket on the VCR.

Connect your existing aerial
cable to the

ANTENNA IN

socket on your VCR.

DECODER UNIT
OR SATELLITE SYSTEM

1

2

3

Connect your TV to the VCR using the
supplied RF connection cable, i.e.
connect the VCR

RF OUT

socket to

the TV

AERIAL IN

socket.

Connect the
VCR to the
mains.

BACK OF
TELEVISION

Optional

SCART (not supplied). If you

have a scart lead connect it to your TV and

LINE 1 IN/OUT

socket on the VCR.

- The advantage of a Scart connection is
improved picture and sound quality during
playback.

SCART LEAD

SCART LEAD

AERIAL

RF CONNECTION

CABLE

AERIAL

RF CONNECTION

CABLE

TINS-3992UMZZ English.book Page 4 Wednesday, May 9, 2001 12:25 PM

5

SHARP Helpline tel: [phone]

or www.sharp.co.uk/support

INSTALLING YOUR VCR

AUTO TUNING

PROCEDURE

This model automatically tunes the TV channels for your area. If the VCR has not previously
been tuned-in, instructions will be given on screen to guide you through this procedure.

1.

Ensure your VCR is still in the STANDBY mode.

2.

Switch on the

TV

.

3.

Select the next available or unused channel on your TV, this will become the dedicated
video channel.

Example of
TV channels

4.

Press the

STOP

button. The VCR will
search and display an ideal RF channel.
Wait for the flashing channel number to appear
on the VCR display, this number will be between
21 and 69.

•

If you are connected via a scart lead, go to step 6.

CAUTION:

5.

Tune the selected channel on your TV.
(Refer to your TV manual for
instructions on how to tune in your TV).

Store this as your VCR channel.

NOTE:

See next page to continue

If the clear button is pressed at this point it will not allow the TV to be tuned to the VCR. Refer
to RF through ON/OFF on page 36.

If the AUTO INSTALLATION screen doesn’t appear when you switch on your VCR or you wish
to reset your VCR and start the installation again, refer to

VCR RESET

at the back of the

book.

1 = BBC1 4 = Channel 4
2 = BBC2 5 = Channel 5
3 = ITV ? = VCR

AUT O I NS T AL L AT I ON

PRESS SET KEY TO START .

SET : EN TER MENU : EX I T

Blue
background
with
White Text

TV SCREEN

TINS-3992UMZZ English.book Page 5 Wednesday, May 9, 2001 12:25 PM

6

SHARP Helpline tel: [phone]

or www.sharp.co.uk/support

INSTALLING YOUR VCR

AUTO TUNING CONTINUED

6.

Press the

SET

button to store the RF channel setting and continue with the

installation.

7.

Ensure your Aerial/Scart cables are

connected to your VCR and then

press the

SET

button to confirm.

Auto install will now search for and tune in
all available channels.

(This may take a few minutes.)

See next page to continue

SET

SET

PL EASE BE SURE THE
AER I AL / S CART CAB LE I S
CONNECT ED TO YOUR VCR .

PRESS SET TO CONT I NUE

SET : ENTER MENU : EX I T

1CH22

AUTOMAT I C T UN I NG .

PL EASE WA I T .

SET : ENTER MENU : EX I T

Button positions for your reference.

REMOTE CONTROL

7.

SET

TINS-3992UMZZ English.book Page 6 Wednesday, May 9, 2001 12:25 PM

7

SHARP Helpline tel: [phone]

or www.sharp.co.uk/support

INSTALLING YOUR VCR

On completion the

MOVE MENU

will appear showing all the channels the VCR was able to

tune in. By pressing

MODE OSD

button, the VCR will change to a blue background. This may

help you see which channel your VCR has tuned in. Using the [ / /

/

] menu select
buttons scroll through the channels to find BBC1. Some channels may be duplicated but with
more interference than others. Search for the best quality picture and using the procedure
below, move this channel to Preset 1. Repeat this procedure for BBC2 - Preset 2, ITV - Preset 3,
etc.

1.

Press [ / /

/

] to highlight

the channel to be moved.

2.

Press the

SET

button to confirm.

3.

Press [ / /

/

] to highlight

the new position for the channel.

4.

Press the

SET

button to confirm.

5.

If any more channels are to be
moved,
repeat procedure from step 3.

6.

Press the button to exit if you are
happy with the channel order.

All the programmes should now
be correctly tuned!

If you wish to, delete or change the
channel order at a later date please refer
to

MANUALLY SORTING

CHANNELS

towards the back of this

book.

See next page to continue

MENU SELECT
BUTTONS

MENU

SET

MOVE 1/5
1 CH 2 1 713
2CH32 8 14
3CH43 9 15
4CH54 10 16
5CH65 11 1 7
61218

CL EAR :CHANNE L SORT
  : SELECTED
SET : ENTER MENU : EX I T

3.

1.

MOVE 1/5
1CH32 7 13
2CH43 8 14
3CH54 9 15
4CH65 10 1 6
5 CH 2 1 11 17
61218

SELECTED :CH5
  : SELECTED
SET : ENTER MENU : EX I T

SET

SET

TINS-3992UMZZ English.book Page 7 Wednesday, May 9, 2001 12:25 PM

8

SHARP Helpline tel: [phone]

or www.sharp.co.uk/support

INSTALLING YOUR VCR

The clock setting screen will now appear.
To set the time and date follow the steps
below:

1.

Press the [ / ] menu select
buttons to select either 12 or 24 hour
clock operation.

2.

Press [

/

] to select TIME. Enter

the time using the

NUMBER

BUTTONS or the [ / ]

buttons. If the minutes or hours are
less than 10, enter the leading 0. If
using the 12 hour clock enter AM or
PM by pressing the

AM/PM

button on the remote control.

3. Press [ / ] to select DATE. Enter

the date using the

NUMBER

BUTTONS or the [ / ]

buttons. For example, for 1st April
enter

01 04.

4. Press [ / ] to select YEAR. Enter

the last two digits of the year using
the

NUMBER BUTTONS or the

[ / ] buttons. For example, for
2001 enter

01. For the year 2002

enter

02.

5. Press the SET button to store the time

and date.

NOTE:

✔

All the programmes should now be correctly tuned in and the clock set.

• You will need to update the clock for Winter/Summer daylight saving.

12 hour example:

24 hour example:

CLOCK

MODE T I ME DAT E YEAR

24H 15:0501/0401

MODE : 24H / 1 2H
 : SELECT  : CHANGE

SET : ENTER MENU : EX I T

CLOCK

MODE T I ME DAT E YEAR

12H 03:05PM 01/04 01

MODE : 24H / 1 2H
 : SELECT  : CHANGE

SET : ENTER MENU : EX I T

AM/PM

TINS-3992UMZZ English.book Page 8 Wednesday, May 9, 2001 12:25 PM

9

www.sharp.co.uk/support

BASIC OPERATION

SCART LEAD CONNECTION (NOT SUPPLIED)

A scart lead can be connected at any time. It is recommended to connect your TV and VCR
in this way as it will provide improved picture and sound quality. Please refer to the connection
diagram on page 4.

IMPORTANT NOTES ON YOUR VCR AND VIDEO
TAPES

VIDEO TAPES

• If you use only good quality video tapes, generally it will not be necessary to clean the
video heads.

• If poor quality tapes are used, or if a tape is loaded after changing VCR location, oxide
from the tape may "clog" the video heads. This will cause the playback picture to be
"snowy", or even disappear.

• To remove minor contamination run a video tape in visual search mode. If this fails, you
will need to have the heads cleaned by a SHARP Service Facility. Please note, if cleaning
is necessary it is not covered by the guarantee.

• Use video tapes which carry the mark.

HOW TO PLAYBACK A VIDEO TAPE

PLAYBACK

1.

Switch on your TV and select the video channel.

2. Carefully push a pre-recorded video

tape into the tape compartment.
This will switch the VCR on.

• If the record-protection tab has
been removed, the VCR will start
playback as soon as the video tape
has been loaded.

3. Press the PLAY/X2 button to

start playback.

See next page to continue

BEFORE YOU PLAYBACK A VIDEO TAPE

Condensation forms in the VCR when it is moved out of or into a warm place.
If you try to playback or record, the video tape and VCR may be damaged.
Turn the VCR on and wait for about two hours until the VCR reaches room
temperature before operating.

SECAMPAL

Record protection tab

PLAY / X2

TINS-3992UMZZ English.book Page 9 Wednesday, May 9, 2001 12:25 PM

10

www.sharp.co.uk/support

BASIC OPERATION

HOW TO PLAYBACK A VIDEO TAPE

• For double speed playback (without sound), press the PLAY/X2 button again.

• To revert to normal playback, press the

PLAY/X2 button again.

• To stop the video tape, press

STOP .

• To eject the tape press

EJECT on the VCR.

SHARP SUPER PICTURE should enhance the picture quality during playback. It is

normally set to ON. To turn

SHARP SUPER PICTURE on or off press SUPER P. on

the VCR front panel.

PICTURE DISTURBANCE DURING PLAYBACK

This VCR has an automatic tracking system which reduces picture disturbance when you start
to playback a video tape. When auto-tracking is in operation flashes on the on-screen
display. If the picture still has disturbance you may need to manually track the video tape:

During PLAYBACK of a video tape.

• Press

CHANNEL or to position picture interference off the TV screen.

(Manual Tracking)

• Press

CHANNEL and buttons together to start Auto Tracking.

PAUSING AND SLOW MOTION

1.

Press the PLAY/X2 button to start the video tape playing.

2. To pause the video tape, press PAUSE/STILL .

• To minimise jitter whilst in pause mode press

CHANNEL or .

• Press the

PLAY/X2 button to resume playback.

3. To playback in slow motion (without sound) press the SLOW button on the remote

control. Slow motion speed can be adjusted using the or buttons next to the slow

button. Picture disturbance can be improved by using the

CHANNEL or

during slow motion playback.

• Press the

PLAY/X2 button to resume playback.

NOTES:

• When using SLOW MOTION function some mechanical noise may be heard.

• There will be picture interference and possibly a change to black and white picture
using Pause and Slow functions.

• PAUSE mode will disengage after about 5 minutes.

PLAY / X2

PLAY / X2

STOP

CHANNEL

CHANNEL

CHANNEL

CHANNEL

PLAY / X2

PAUSE/STILL

CHANNEL

CHANNEL

PLAY / X2

SLOW

CHANNEL

CHANNEL

DPSS

INPUT SELECT

CHANNEL

AM/PM

SLOW

TAPE

SPEED

TV/VCR

REC

PAUSE/STILL

REW FF

PLAY / X2

STOP

7809

PLAY / X2

TINS-3992UMZZ English.book Page 10 Wednesday, May 9, 2001 12:25 PM

11

www.sharp.co.uk/support

BASIC OPERATION

HOW TO PLAYBACK A VIDEO TAPE

FAST FORWARDING/REWINDING A VIDEO TAPE

1.

Press STOP to stop the video tape.

2. Press the FAST FORWARD /REWIND buttons on the remote control or on

the VCR front panel.

3. To stop fast forward/rewind, press STOP .

FORWARD/REVERSE VISUAL SEARCH

1.

During playback to select search mode, press the

FAST FORWARD or REWIND buttons on

the remote control, or on the VCR front panel.

2. Press the PLAY/X2 button to resume playback.

OR

3. To decrease the speed, during visual search mode press

FAST FORWARD or REWIND again.

4. Press the PLAY/X2 button.

NOTE:

IMMEDIATE RECORDING

SELECTION OF A CHANNEL

Select the channel you wish to record by using the

NUMBER BUTTONS

on the VCR remote

control, or select the next/previous channel by pressing the

CHANNEL / buttons

on the remote control or on the VCR front panel.

To change between single digit and 2-digit channel numbers, press the button.

For example, for channel 24, press the button then press

2 4.

• There will be picture interference and possibly a change to black and white picture
using Visual Fast Forward/Rewind functions.

FF REW

FF REW

PLAY / X2

FF REW

PLAY / X2

CHANNEL

CHANNEL

REMOTE CONTROL

TINS-3992UMZZ English.book Page 11 Wednesday, May 9, 2001 12:25 PM

12

www.sharp.co.uk/support

BASIC OPERATION

IMMEDIATE RECORDING CONTINUED

TAPE SPEED SELECTION

Your VCR has three tape speeds: SP (Standard Play), LP
(Long Play) and EP (Extended Play).
Press the

TAPE SPEED button on the remote

control or on the VCR front panel to select the desired
setting.

It is recommended that EP recordings are only played back on the VCR on which they were
originally recorded.

You can record the channel you are watching or a different channel.

1. Insert a video tape into your VCR.

2. Select the channel you wish to record on the VCR as

above.

3. To start recording, press REC .

4. To pause during recording, press PAUSE/STILL .

5. To continue recording, press REC .

6. To stop recording, press STOP once.

SIMPLE TIMED RECORDING:

1. Press REC .

2. To specify a stop time, each additional press of

REC will delay the stop time by 10

minutes.

3. To stop recording at any time, press

STOP once.

NOTES:

• If the tape ends before the recording is complete the VCR will stop recording, rewind,
eject the tape and place the VCR into STANDBY mode, or just eject the tape and place
the VCR in STANDBY timer mode if the VCR is in timer record mode.

• If the VCR ejects the video tape when you press

REC the tape is record protected.

i.e. record protection tab has been removed.

Cassette
Length

Recording
Time

E-240 In Minutes

SP 240
LP 480
EP 720

0

STOP 15:30

0

REMOTE CONTROL

REMOTE CONTROL

TINS-3992UMZZ English.book Page 12 Wednesday, May 9, 2001 12:25 PM

13

www.sharp.co.uk/support

BASIC OPERATION

HOW TO USE TO MAKE A RECORDING
(VC-MH714HM ONLY)

Before you start!

• If the Timer Standby symbol appears on the VCR display, press the

TIMER

ON/OFF

button to remove the symbol.

• Check that the VCR clock is displaying the correct time.

VIDEOPLUS+ allows you to program the VCR to record up to eight programmes using the
VIDEOPLUS+ numbers published in TV listings (refer to your daily newspaper or TV magazine).

1.

Press the PLUSCODE button on the remote
control.

2.

Enter the VIDEOPLUS+ number from the TV
listing using the

NUMBER BUTTONS

.

NOTE:

3.

Press the [ / ] menu select buttons to select
ONCE, WEEKLY, DAILY.

• If you want to make additional recordings at the same
time each day or week, then use

[/]

to select the

WEEKLY, or DAILY option as appropriate.

4.

Press the

SET

button to confirm.

NOTE:

The first time that you use VIDEOPLUS+ to make a
recording on each channel Preset, (PR) may be
highlighted on the On-Screen Display.

5.

Enter the channel number you wish to record
using the

NUMBER BUTTONS

, for

example if you wish to record channel 2 press

0 2

. The VCR will remember this for the future.

See next page to continue

• An ERROR message will appear if you have entered a number that is not a current

VIDEOPLUS+ number. If this happens press

CLEAR

to delete the numbers as

required and enter the correct VIDEOPLUS+ number.

• Check that the menu list agrees with the times shown in the TV listing. If it does not press

CLEAR

to return to the VIDEOPLUS+ menu, and re-enter the correct VIDEOPLUS+

number.

→

P L US CODE NO . -

ONCE WE E K L Y D A I L Y

MENU SET

CLEAR

DISPLAY

PLUSCODE

MODE OSD

TIMER

ON/OFF

AUDIO

OUT

SKIP

SEARCH

ZERO
BACK

231

4

5

6

MENU

SELECT

BUTTONS

SET

1/2
DATE PR START STOP
21/06 02 12:00 13:00 SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

PR : BBC 2
 : SELECT  : CHANGE
SET : ENTER MENU : EX I T

REMOTE CONTROL

TINS-3992UMZZ English.book Page 13 Wednesday, September 12, 2001 9:46 AM

14

www.sharp.co.uk/support

BASIC OPERATION

HOW TO USE TO MAKE A RECORDING
(VC-MH714HM ONLY)

6.

If you wish to change the

RECORDING

SPEED

, use the

[/]

to highlight SP. Press

[ / ] to select standard play (SP), long

play (LP) or extended play (EP) as required.

7.

Press the

SET

button to confirm the

programme. The VIDEOPLUS+ menu will

reappear. If you wish to enter further

VIDEOPLUS+ recordings repeat this procedure.

8.

When you have completed entering the timer

settings, press the

MENU

button to

remove the menu from the TV screen.

9.

Ensure that the tape on which you

wish to record is inserted into the VCR,

then press the TIMER ON/OFF

button once to place the VCR in TIMER

STANDBY mode. will be shown on

the display.

NOTES:

• You may also access the VIDEOPLUS+ menu by the following procedure:

i.

Press the

MENU

button.

ii.

The VIDEOPLUS+ option will be highlighted. Press the

SET

button to confirm.

Continue from step 2 of this procedure.

• If the symbol flashes a video tape has not been inserted into the VCR.

• If the video tape is ejected when the VCR tries to record the record protection tab has
been removed.

• During recording, press

STOP

to cancel the recording. If there are further

recordings to be made, the VCR will return to Timer Standby.

1/2
DATE PR START STOP
21/060212:0013:00SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

SP / LP :

TAPE

SPEED

 : SELECT  : CHANGE

SET : ENTER MENU : EX I T

6.

→

P L US CODE NO . -

ONCE WE E K L Y D A I L Y

7.

SET

SET

TINS-3992UMZZ English.book Page 14 Wednesday, September 12, 2001 9:46 AM

15

www.sharp.co.uk/support

BASIC OPERATION

HOW TO SET A DELAYED RECORDING

You can make a maximum of eight delayed recordings up to a year in advance.

The example shown is for 24-hour clock operation. To change to12-hour clock operation refer

to the

MANUALLY SETTING THE CLOCK

section of this manual.

12-hour clock am/pm can be selected using the

AM/PM

button on the remote

control.

Before you start!

• If the Timer Standby symbol appears on the VCR display, press the

TIMER ON/OFF

button to remove the symbol.

• Check that the VCR clock is displaying the correct time.

SETTING A RECORDING

For example: Recording a programme on channel 3 from 21:05 to 22:30 on July 9th.

1.

Press

STOP

to ensure that the VCR

is switched on.

2.

Press the

MENU

button

.

3.

Press the[ / ] menu select buttons to

select

TIMER

. Press the

SET

button to

confirm.

4.

Press the

SET

button

again, the on-screen
display will now show today’s date.
If you wish to change the date use the
[ / ]or

NUMBER BUTTONS

. If you
use the number buttons, enter two digits for
the day, then two for the month. For example
for July 9th, press

0 9

(9th), then

0 7

(July).
When the correct date for your recording is
shown, press the

menu select button to

move to the next setting.

5.

If you want to make additional recordings at
the same time each day or week, use the
[ / ] buttons to select D (daily) or W
(weekly). Then press to move to the next
setting.

6.

Enter the channel number using the
[ / ]or the

NUMBER BUTTONS

. For
example to record a programme on channel
3, press 0 3. Then press to move to the next
setting.

See next page to continue

MENU SCREEN

MEN U
V I D EOPL US +

TIMER

MOD E
SET UP

1/2

DATE PR START STOP

21/060212:0013:00SP

9/07D -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

REMOTE CONTROL

1/2

DATE PR START STOP

21/060212:0013:00SP

9/07 -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

3.

4.

5.

MENU SET

CLEAR

DISPLAY

SV/V+/
TIMER

MODE OSD

TIMER

ON/OFF

AUDIO

OUT

SKIP

SEARCH

ZERO
BACK

231

MENU

SELECT

BUTTONS

SET

SET

TINS-3992UMZZ English.book Page 15 Monday, June 4, 2001 9:21 AM

16

www.sharp.co.uk/support

BASIC OPERATION

HOW TO SET A DELAYED RECORDING

7.

Enter the start time using the[ / ] or

NUMBER BUTTONS

, hours first then

minutes (when entering less than 10 hours or

minutes add a '0' before the number), for

example for 21:05 start, press

2 1 0 5

.

Then press to move to the next setting.

8.

Enter the stop time, for example for 22:30 stop,
press 2 2 3 0 .

9.

If you wish to change the

RECORDING

SPEED

, use the

[/]

to highlight SP.

Press[ / ]to select standard play (SP),

long play (LP) or extended play (EP) as

required.

10.

Press the

SET

button to confirm.

• The MENU now shows all the timer settings you

have entered. If you wish to make additional

timer recordings, repeat this procedure.

11. When you have completed entering timer

settings, press the

MENU button to

remove the menu from the TV screen.

12. Ensure that the tape on which you wish to

record is inserted into the VCR, then press the

TIMER ON/OFF button once to place

the VCR in TIMER STANDBY mode. will be

shown on the display.

NOTES:

• If the symbol flashes a video tape has not been inserted into the VCR.

• If the video tape is ejected when the VCR tries to record the record protection tab has
been removed.

• During recording, press

STOP to cancel the recording. If there are further

recordings to be made, the VCR will return to Timer Standby.

1/2

DATE PR START STOP

21/060212:0013:00SP

9/07D03 21:05 -:-- SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

1/2
DATE PR START STOP
21/060212:0013:00SP

9/07D03 21:05 22:30 LP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

7.

9.

SET

TINS-3992UMZZ English.book Page 16 Monday, June 4, 2001 9:21 AM

17

www.sharp.co.uk/support

BASIC OPERATION

HOW TO CHECK, CHANGE AND CANCEL A DELAYED
RECORDING

Before you start!

• If the Timer Standby symbol appears on the VCR display,

press the

TIMER ON/OFF button to remove the

symbol.

CHECKING A RECORDING

1. Press STOP to switch on the VCR.

2. Press the MENU button.

3. Press[ / ]to select TIMER. Press the

SET button to confirm.

• All the delayed recordings in the VCR’s memory
will be shown.

4. If the settings are correct press the MENU

button to exit.

• If you wish to change or cancel any settings,
follow the procedures below.

CHANGING A RECORDING

1. Follow steps 1 to 3 of CHECKING A

RECORDING above.

2. To change a delayed recording, press

[ / ] to highlight the recording, then press

the

SET button to select.

3. Press[/]to highlight the setting to be

changed and correct it by using the[ / ]

or the

NUMBER BUTTONS.

4. When all corrections are complete press the

SET button to confirm, then press the

MENU button to exit.

CANCELLING A RECORDING

1. Follow steps 1 to 3 of CHECKING A

RECORDING above.

2. To cancel a delayed recording, press

[ / ]to highlight the recording to be

cancelled, then press

CLEAR.

3. Press the MENU button to exit.

NOTE:

• If there are some programmes to be recorded, do not forget to press TIMER ON/OFF

button to return the VCR to Timer Standby mode.

MENU SCREEN

TIMER

MOD E

SET UP

 : SELECT

SET : ENTER MENU : EX I T

SET

1/2

DATE PR START STOP

21/060212:0013:00SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

SET

SET

1/2

DATE PR START STOP

21/060212:0013:00SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- --

TINS-3992UMZZ English.book Page 17 Monday, June 4, 2001 9:21 AM

18

www.sharp.co.uk/support

ADVANCED OPERATION

AUDIO AND YOUR VCR

HI-FI STEREO SOUND

Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a
scart lead, or audio equipment connected with audio phono leads. The VCR is normally set

so that stereo sound is possible. The sound output from the VCR is controlled by the

AUDIO OUT button on the remote control. If you wish to change the sound output you

can use the

AUDIO OUT button as follows:

• Press the

AUDIO OUT button once. The LEFT audio channel will be sent to BOTH

speakers.

L will appear on the VCR display.

• Press the

AUDIO OUT button again. The RIGHT audio channel will be sent to BOTH

speakers.

R will appear on the VCR display.

• Press the

AUDIO OUT button a third time and the MONO track will be sent to BOTH

speakers.

L and R will not appear on the VCR display.

• Pressing the

AUDIO OUT button a fourth time, normal Hi-Fi stereo sound will be

heard.

L and R will appear on the VCR display.

NICAM Hi-Fi STEREO SOUND

Your VCR can receive and record NICAM sound. The VCR is normally set so that NICAM sound
is possible if it is present on the receiving signal, otherwise the VCR will automatically switch to
receive the mono signal. NICAM sound can be turned off. If you wish to do this follow the
procedure below:

1. Press the MENU button to display the

main menu on the screen.

2. Press the [ / ] menu select buttons to

select MODE then press the

SET button to

confirm.

• The MODE menu will be displayed with NICAM
selected.

3. Press [ / ]to select OFF.

4. Press the SET button to confirm and return to the main menu screen.

5. Press the MENU button to exit to normal screen.

NOTES:

• If the tape being played back does not carry sound recorded on Hi-Fi tracks, L and R

will not appear on the display.

• lf the sound contains ‘crackling’ or ‘popping’ noises the sound quality may be

improved by adjusting the tracking using the

VCR CHANNEL / buttons.

• If the poor quality is for a long period the VCR will automatically select the mono track

and the sound will be in mono.

• NICAM sound may not be stereo.

➝NICAM AUTO OF F

COLOUR AUTO PA L

SETS

ET

TINS-3992UMZZ English.book Page 18 Monday, June 4, 2001 9:21 AM

19

www.sharp.co.uk/support

ADVANCED OPERATION

AUDIO AND YOUR VCR

CONNECTING TO AUDIO EQUIPMENT

The diagram below shows how to connect your VCR to audio equipment. When connected
in this way stereo sound is possible from the speakers.

RF OUT

SORTIE ANTENNE

A

N

T

E

N

N

A

IN

E

N

T

R

E

E

+

BACK OF

EXISTING AERIAL

CABLE

RF CONNECTION CABLE

RF-OUT

AUDIO OUT

AMPLIFIER

L and R

TELEVISION

AERIAL IN

AUDIO PHONO LEADS

(NOT SUPPLIED)

TINS-3992UMZZ English.book Page 19 Monday, June 4, 2001 9:21 AM

20

www.sharp.co.uk/support

ADVANCED OPERATION

PLAYBACK OF A VIDEO TAPE

CHECKING THE AMOUNT OF TAPE REMAINING

When you load a video tape into the VCR it can calculate approximately the amount of
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you
automatically.
To display the amount of video tape remaining:

1. Load the video tape into the VCR

2. Press DISPLAY on the remote control as many times as necessary until “R” appears on

the VCR display. The tape will wind forward for a few seconds and then return to its
original position. The tape remaining will be shown on the VCR display in hours and
minutes.
By pressing the

TAPE SPEED button on the remote control the remaining time will

change between standard play, long play and extended play.

For example,
in standard play 1 hour 23 minutes is left on the tape:

in long play 2 hours 46 minutes is left on the tape:

in extended play 4 hours 9 minutes is left on the tape:

NOTES:

PLAYING BACK A VIDEO TAPE REPEATEDLY

You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:

1. Press the MENU button to display the

main menu on the screen.

2. Press the[ / ]menu select buttons to

select MODE.

3. Press the SET button.

4. Press [ / ]to select REPEAT.

5. Press [/]to select ON or OFF.

6. Press the SET button to confirm and return

to the main menu screen.

7. Press the MENU button to exit to normal

screen.

• If tape remaining function is interrupted, the remaining time will not be displayed.

• If less than 5 minutes of tape remains the display will flash.

MODE MENU SCREEN

BLUE MUTE AU TO OFF

➝REPEAT ON OFF

 : SELECT  : CHANGE

S E T : E N T E R ME N U : EX I T

SET

SET

TINS-3992UMZZ English.book Page 20 Wednesday, May 9, 2001 12:25 PM

21

www.sharp.co.uk/support

ADVANCED OPERATION

LCD DISPLAY

TIME OF DAY

Shows current time of day, if the clock is set.

Press the

DISPLAY

button until the time of day

appears. For example, 21:20 appears:

CHANNEL STATUS

Shows the current VCR channel preset. Press the

DISPLAY

button until the channel number

appears, for example:

TAPE COUNTER AND ZERO BACK

Tape counter measures the current position of the video tape in real time. ZERO BACK uses the
tape counter to determine a specific point on a tape you may wish to return to.

1.

Press the

DISPLAY

button until tape

counter appears, for example:

2.

To identify the current position on a video tape

press the

CLEAR

button and the tape

counter will appear:

When you wish to return to this position on the video tape, press

ZERO BACK

button.

The tape will rewind/advance to this point.

NOTE:

DISPLAY BRIGHTNESS

The LCD display brightness can be changed to suit the ambient lighting in the room. Switch
on the VCR (ensure the menu screen is not on) then press and hold the DISPLAY button for
approximately 2 seconds. This will reduce the brightness of the VCR display. Repeat the
process to change the display back to the previous setting.

• The tape counter will only operate on recorded sections of tape.

TINS-3992UMZZ English.book Page 21 Monday, June 4, 2001 9:24 AM

22

www.sharp.co.uk/support

ADVANCED OPERATION

BLUE MUTE

The TV screen will be blue if a TV channel with no signal is selected, an unrecorded section of
tape is played or the quality of the recording on the tape is poor. Select OFF in the mode
menu to disable this feature.

1.

Press the

MENU

button to display the

main menu on the screen.

2.

Press the[ / ] menu select buttons to

select MODE.

3.

Press the

SET

button.

4.

Press the [ / ] menu select buttons to

select BLUE MUTE.

5.

Press

[/]

menu select buttons to select

AUTO or OFF.

6.

Press

SET

to confirm and then

MENU

to return to the normal screen

COLOUR

If the VCR is playing poor quality recording, the picture may turn black and white. Selecting

PAL may improve this (depending on the recording), although coloured speckles may appear

on black and white recordings.

1.

Follow steps 1 to 3 from BLUE MUTE above.

2.

Press the [ / ] menu select buttons to select COLOUR.

3.

Press

[/]

menu select buttons to select AUTO or PAL.

4.

Press

SET

to confirm and then

MENU

to return to the normal screen.

MODE MENU SCREEN

NICAM AUTO OFF
COLOUR AUTO PAL
BLUE MUTE AUTO OFF
REPEAT ON OFF

SET

MENU SET

CLEAR

SV/V+/
TIMER

MODE OSD

TIMER

ON/OFF

AUDIO

OUT

SKIP

SEARCH BACK

231

SET

SET

REMOTE CONTROL

TINS-3992UMZZ English.book Page 22 Monday, June 4, 2001 9:24 AM

23

www.sharp.co.uk/support

ADVANCED OPERATION

SEARCHING THE VIDEO TAPE

SKIP SEARCHING THE VIDEO TAPE

You can search the tape in 30 second time intervals. To do this follow the procedure below:

1.

Press

PLAY/X2

to start the video tape

playing.

2.

Press the

SKIP SEARCH

button on the

remote control.

The number of times you press

SKIP SEARCH

determines the forward search time.

• After searching, normal playback
will resume automatically

DIGITAL PROGRAMME SEARCH SYSTEM (DPSS)

Your VCR records a marker signal on the tape at the start of each recording. These signals can

be used later to locate the starting point of a recording.

Press

DPSS

/

to locate a previous programme or the next programme.

For example,

1.

Load the video tape into the VCR.

2.

Press

DPSS

three times. DPSS 3 will appear on the on-screen display, and the VCR

will fast forward to locate the third recording after the current one.

3.

Press

DPSS

once. DPSS - 1 will appear on the on-screen display and the VCR will

rewind to locate the beginning of the current recording.

4.

To cancel the search before it has finished, press

STOP

or

PLAY/X2

.

NOTES:

• Recordings must be longer than 3 minutes.

• The starting point of playback may vary.

• This feature will only work with video tapes recorded on a VCR with the DPSS feature.

1 press = 30 seconds.
2 presses = 1 minute.
3 presses = 1 minute 30 seconds.
4 presses = 2 minutes.

PLAY / X2

DPSS Signals

Current tape position

Fast ForwardRewind

DPSS
Number

PLAY / X2

TINS-3992UMZZ English.book Page 23 Monday, June 4, 2001 9:24 AM

24

www.sharp.co.uk/support

ADVANCED OPERATION

RECORDING FROM OTHER EQUIPMENT

You can record video and audio signals from various external sources, such as a camcorder,
onto a video tape using your VCR.

For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR:

1.

Connect your signal source (eg.
Camcorder, Digital Camera etc) to the
desired scart socket on the back of the
VCR using the manufacturers
recommended cable (not supplied).

2.

Ensure that the tape on which you wish to
record is inserted into the VCR.

3.

Press the

INPUT SELECT

button
on the remote control until the VCR
display shows

L2

.

4.

Press

REC

to start recording.

OTHER CONNECTIONS
POSSIBLE!

• If you wish to record from a source

connected to LINE 1 IN/OUT, select

L1

.

Press

REC

to start recording.

• If you wish to record from a source

connected with audio phono leads to the

sockets on the front of the VCR, select

L3

.

Press

REC

to start recording.

NOTE:

• There are many different ways of connecting external equipment to your VCR. Please
refer to your equipment operation manuals for further information.

Optional Scart connection (not supplied)

Mono/Stereo Camcorder

RF OUT

SORTIE ANTENNE

ANTENNA IN

ENTREE

R

SORTIE

REMOTE CONTROL

7

8

0

9

➘

Input Select

L

I

N

E IN 3

V

I

DEO

L • AUDIO • R

TINS-3992UMZZ English.book Page 24 Monday, June 4, 2001 9:24 AM

25

www.sharp.co.uk/support

SPECIAL FEATURES ON YOUR VCR

CHILD LOCK

You can lock your VCR with this feature. It will work even when the VCR is in STANDBY,
preventing children from operating the VCR.

TO ENGAGE CHILD LOCK

Press and hold the

CHILD LOCK

button on the remote control for about 2 seconds.

flashes and then remains lit on the VCR display confirming that CHILD LOCK
has been activated.
Regardless of what other operating buttons are touched, the VCR will continue to operate in

its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.

TO DISENGAGE CHILD LOCK

Press and hold the

CHILD LOCK

button for about 2 seconds.

starts flashing and then disappears. CHILD LOCK is disengaged.

NOTES:

• If you attempt to change modes by pressing another button while CHILD LOCK is on,
the indicator will flash on the VCR display.

• If power is interrupted for more than 60 seconds (due to power failure etc), CHILD LOCK
may disengage.

TINS-3992UMZZ English.book Page 25 Wednesday, May 9, 2001 12:25 PM

26

www.sharp.co.uk/support

ADVANCED OPERATION

DECODER SWITCHING OPERATION

If you have a separate decoder connected to the VCR’s L2 input as previously shown in the
“Connecting the Cables” section, you will need to set the decoder function to ON in order to
record the descrambled signal and/or watch it on your TV. Now, when the VCR receives a
scrambled signal it is output via LINE 2 terminal to the decoder. The decoder then outputs the
descrambled signal back to LINE 2 terminal and the signal can be recorded. The VCR outputs
the descrambled signal to your TV through the LINE1 terminal and you can watch the
descrambled picture.

When making recordings using a separate decoder connected as shown remember to leave
the decoder function ON.

If you connect a decoder unit to the VCR, the decoder unit provides a switching signal which
will automatically allow your TV to display the descrambled signal routed through the VCR. To
use this feature make sure that the VCR is connected to both TV and decoder unit by SCART
leads. Then:

• Press STANDBY

to place the VCR in STAND-BY mode. OR

• Press TV/VCR on the remote control to place the VCR in ‘VCR mode’. ‘VCR’ will
appear on the display.

TINS-3992UMZZ English.book Page 26 Wednesday, May 9, 2001 12:25 PM

27

www.sharp.co.uk/support

CUSTOMISED INSTALLATION

MANUALLY TUNING A CHANNEL

• It should not be necessary to tune in a broadcast channel manually except in unusual
circumstances such as poor signal.

To manually tune in a channel follow the procedure below.

1.

Press

MENU

.

2.

Press the [ / ] menu select buttons
to select SET UP. Press

SET

to confirm.

3.

CHANNEL PRESET

will be

highlighted. Press

SET

.

4.

Press [ / ] to select

CHANNEL

.

5.

VC-MH704LM only
IMPORTANT NOTE:

Press to select CH or CC. This will
determine whether off air (CH) or cable
(CC) is tuned first. Note that both off air
and cable will be tuned regardless of the
setting.

6.

Press

[/]

to start tuning in either
direction. Tuning will stop when a channel
is received. If it is not the desired channel,
press

[/]

to continue tuning.

7.

Press [ / ] to select

FINE

TUNING

. Press and hold

[/]

until

the sharpest colour picture is obtained.

IMPORTANT NOTE:

8.

If you connect an independent decoder,
you must press [ / ] to select
DECODER, then select

[/]

to turn

the decoder function ON.

9.

Press [ / ] to select

SKIP

.
The SKIP function determines whether the
channel can be selected when using the

CHANNEL

/ instead of the

NUMBER BUTTONS

.

10.

Press

[/]

to select ON or OFF for

this option.

11.

Press

SET

to confirm.

12.

Press

MENU

to leave this function.

CHANNEL PRESET

CHANNEL SORT

CLOCK

➔

PRESET 1

CHANNE L CH 2 1

FINE TUNING

▲

▲

SKIP ON OFF

CABLE RECEPTION

VC-MH704LM only

MENU SET

CLEAR

SV/V+/
TIMER

MODE OSD

231

Remote Control

Station

Signals VHF

Real
Channel
Numbers

A

B
C
D

E

F

G

H

J

01
02
03
04
05
06
07
08
09

TINS-3992UMZZ English.book Page 27 Monday, June 4, 2001 9:27 AM

28

www.sharp.co.uk/support

CUSTOMISED INSTALLATION

MANUALLY SORTING CHANNELS

SORTING THE CHANNELS INTO YOUR PREFERRED ORDER

1.

Press the MENU button.

2. Press the [ / ] menu select buttons to

select SET UP. Press the

SET button to

confirm.

3. Press [ / ] to select CHANNEL SORT. Press

the

SET button to confirm.

4. The MOVE position will be highlighted. Press the

SET button to confirm.

5. Press [ / / / ] to highlight the

channel to be moved. Press the

SET

button to confirm.

6. Press [ / / / ] to highlight the new

position for the channel. Press the

SET

button to confirm.

7. If any more channels are to be moved, repeat

procedure from step 5.

8. When all the channels are in your preferred

order, either press the

CLEAR button to

return to the CHANNEL SORT menu or press the

MENU button to leave the MENU

function.

NOTES:

If when moving channels the picture becomes
unclear and the on-screen display is unreadable,
the MODE OSD button can be used to toggle
between a blue background and the normal
picture.
The blue background will be shown until either
another channel is selected or the MODE OSD
button is pressed again.

5.

MOVE 1/5
1CH43 7 13
2CH54 8 14
3CH65 9 1 5
4CH21 10 1 6
5CH50 11 17
6 CH 3 2 12 18

6.

MOVE 1/5
1 CH 3 2 713
2CH43 8 14
3CH54 9 1 5
4CH65 10 1 6
5CH21 11 1 7
6CH50 12 18

Remote Control

MENU SELECT
BUTTONS

MENU

SET

MENU SCREEN

2.

V I D EOPL US
TIMER
MOD E

SET UP

SET

SET

SET

SET

SET

TINS-3992UMZZ English.book Page 28 Wednesday, May 9, 2001 12:25 PM

29

www.sharp.co.uk/support

CUSTOMISED INSTALLATION

MANUALLY SORTING CHANNELS

DELETING CHANNELS

If there is a channel you wish to delete from the VCR memory, you can follow the procedure
below.

1. Press the MENU button.

2. Press the [ / ] menu select buttons to

select SET UP. Press the

SET button to

confirm.

3. Press [ / ] to select CHANNEL SORT. Press

the

SET button to confirm.

4. Press [ / ] to select CANCEL. Press the

SET button to confirm.

5. Press [ / / / ] to highlight the

channel to be cancelled.

6. Press the SET button twice to cancel the

channel.

7. When all the channels you wish have been

cancelled, either press the

CLEAR button

to return to the CHANNEL SORT menu or press

the

MENU button to leave the MENU

function.

NOTES:

If when deleting channels the picture becomes
unclear and the on-screen display is unreadable,
the MODE OSD button can be used to toggle
between a blue background and the normal
picture.
The blue background will be shown until either
another channel is selected or the MODE OSD
button is pressed again.

5.

CANCE L 1 / 5
1 CH 5 0 713
2CH32 8 14
3CH43 9 15
4CH54 10 1 6
5CH65 11 1 7
6CH21 12 18

6.

CANCE L 1 / 5
1CH32 7 13
2CH43 8 14
3CH54 9 1 5
4CH65 10 1 6
5CH21 11 17
61218

Remote Control

MENU SELECT
BUTTONS

MENU

SET

MENU SCREEN

2.

V I D EOPL US
TIMER

MOD E

SET UP

SET

SET

SET

SET

TINS-3992UMZZ English.book Page 29 Wednesday, May 9, 2001 12:25 PM

30

www.sharp.co.uk/support

CUSTOMISED INSTALLATION

MANUALLY SETTING THE CLOCK

This procedure will allow you to set the clock manually.

1. Press the MENU button.

2. Press the [ / ] menu select buttons to

select SET UP. Press the

SET button to

confirm.

3. Press [ / ] to select CLOCK. Press the

SET button to confirm.

4. Press [ / ] to select either 12 or 24 hour

clock.

5. Press [/] to select TIME. Enter the time

using the

NUMBER BUTTONS or the

[ / ] buttons. If the minutes or hours are

less than 10, enter the leading 0. If using the 12

hour clock enter AM or PM by pressing the

AM/PM button on the remote control.

6. Press [/] to select DATE. Enter the date

using the

NUMBER BUTTONS or the

[ / ] buttons. For example, for 1st April

enter

01 04.

7. Press [/] to select YEAR. Enter the last two

digits of the year using the

NUMBER

BUTTONS or [ / ]. For example, for

2001 enter

01. For the year 2002 enter 02.

8. Press the SET button to confirm.

NOTE:

• You will need to update the clock for Summer/Winter daylight saving.

SET UP

CHANNE L PR ES E T
CHANNE L SORT

CLOCK

 : SELECT  : CHANGE
SET : ENTER MENU : EX I T

CLOCK

MODE T I ME DA T E Y EAR

24H 0:00 01/04 01

*

MODE : 24H / 1 2H
 : SELECT  : CHANGE

SET : ENTER MENU : EX I T

Remote Control

MENU SELECT
BUTTONS

MENU

SET

3.

4.

SET

SET

SET

TINS-3992UMZZ English.book Page 30 Wednesday, May 9, 2001 12:25 PM

31

www.sharp.co.uk/support

MORE INFORMATION ABOUT YOUR VCR

VCR DISPLAY

NOTE:

SELECTING THE OUTPUT FROM THE VCR

If your VCR is connected to your TV with a scart lead, when you start to play a video tape the
VCR will automatically switch its output so that playback picture is shown on the TV.

In this case ‘VCR’ will appear on the VCR display.

You can manually override this by pressing the

TV/VCR button on the remote control.

Now the TV broadcast channel will be seen on the TV screen and ‘VCR’ will disappear from
the VCR display.

• Pressing

TV/VCR again will return the TV picture to the playback picture.

• Some models do not have all the features shown, therefore, they will not appear on the
display.

1. TIMER RECORD indicator.

2. VCR MODE indicator.

3. TAPE MOTION STATUS

indicator

4. RECORDING indicator.

5. AUDIO OUTPUT indicator.

6. CHILD LOCK indicator.

7. TAPE SPEED indicator.

8. VIDEO PROGRAMMING

SYSTEM/PROGRAMME
DELIVERY CONTROL indicator.

9. DECODER indicator.

10. CLOCK, TAPE COUNTER,

TAPE STATUS AND CHANNEL
PRESET STATUS .

TINS-3992UMZZ English.book Page 31 Wednesday, May 9, 2001 12:25 PM

32

www.sharp.co.uk/support

MORE INFORMATION ABOUT YOUR VCR

ON-SCREEN DISPLAY

All the information you need on the VCR status will be summarised on the on-screen display.

If you are recording, playing back a tape or watching a broadcast on the video channel you

can call up three standard on-screen displays. The display can be selected by pressing the

MODE OSD button on the remote control, 1,2,3 or 4 times.

1. AUTO, the current mode and channel

number will be displayed for 3 seconds when an
operation or number button is pressed.

3. COUNTER, this display will show the tape

counter and amount of tape remaining.

4. DISPLAY OFF, this will remove the display

from the screen.

NOTES:

• The default time and date will not be displayed if the clock has not been set.

• The VCR will return to display

1. each time it is switched on.

• If you are recording from this VCR to another, make sure you remove the display from
the screen otherwise it will be recorded.

1.

■ 1CH59
NICAM

ST EREO

SP L R

Programme number and channel
Tape Status
NICAM signal
Audio output mode
Tape speed

Tape remaining
Time
Date
Tape counter

2.

■ 1CH59
SUPER P . ON N I CAM

ST EREO

SP L R

22:00 REM1:05

9/07 01 0:00.00

3.

REM1:05

0:00. 00

2. FULL, all the active features will also be

shown on screen.

TINS-3992UMZZ English.book Page 32 Wednesday, May 9, 2001 12:25 PM

33

MORE INFORMATION ABOUT YOUR VCR

SPECIFICATIONS

• Specifications are subject to change without notice as part of our policy
of continuous improvement.

• No liability is accepted for any inaccuracies or omissions in this
publication, although every possible care has been taken to make it
complete and as accurate as possible.

Format: VHS PAL standard
Number of heads: SIX
Video signal system: PAL colour or monochrome signal: 625 lines
Hi-Fi audio recording
system:

Deep layer recording system conforming to
stereo Hi-Fi VHS standard.

Maximum playing time: 240 min. with E-240 video cassette in Standard

Play (SP) mode
480 min. with E-240 video cassette in Long Play
(LP) mode
720 min. with E-240 video cassette in Extended

Play (EP) mode
Tape width: 12.7 mm
Tape speed: 23.39 mm/s Standard Play (SP)

11.70 mm/s Long Play (LP)

7.8mm/s Extended Play (EP)
Antenna: 75 Ω unbalanced
Reception channels: UHF channel 21-69

(

VHF Channels A-J VC-MH704LM only)
RF output signal: UHF channel 21-69
Power requirement: AC 230-240V, 50 Hz
Power consumption:

17 W approx. (Standby power consumption 2.5W)
Operating temperature: 5 ˚C to 40 ˚C
Storage temperature: -20 ˚C to 55 ˚C
Video input: 1.0 Vp-p, 75 Ω
Video output: 1.0 Vp-p, 75 Ω
Audio input: Line1&2: -3.8 dBs, 10 kΩ, Line 3: -3.8 dBs, 47 kΩ
Audio output: Line1&2: -3.8 dBs, 1 kΩ, Audio out: -3.8 dBs, 1 kΩ
Hi-Fi audio: Dynamic range: ~90dBs typ. (SP);

Frequency response: 20 Hz - 20 kHz;

Wow and Flutter:<0.005% Wrm (JIS A)
Dimensions: 360(W) x 289(D) x 93(H) mm
Weight: 3.2 kg (approx.)
Supplied accessories: 75 Ω RF Connection cable, operation manual,

remote control, AA/R6/UM3 battery (x2)

TINS-3992UMZZ English.book Page 33 Wednesday, May 9, 2001 12:25 PM

34

www.sharp.co.uk/support

TROUBLESHOOTING

TROUBLESHOOTING

BEFORE REQUESTING SERVICE!

The following conditions do not always denote trouble. Therefore, perform the checks
described below before calling for service. If the problem cannot be corrected by the use of
this guide, remove the mains plugs from the wall socket and contact the dealer or supplier
from whom the unit was purchased in order to obtain service. Where this is not possible, please
contact the telephone number listed below, you will then be given details of how to obtain
service.

Tel.

08705 274277

(office hours)

or [phone]

if telephoning from Ireland

- Please note: All calls will

be charged at local rate.

AREA PROBLEM POSSIBLE CAUSE/CURE

INSTALLATION TV will not tune in to

the VCR.

• Check all the cables are correctly
connected.

• Check your TV manual for correct tuning of
your TV.

Auto Installation
screen does not
appear when the VCR
is switched on OR Auto
Installation is not
complete.

• Reset the VCR and complete AUTO
INSTALLATION again. (Refer to VCR Reset at
the back of the book.)

POWER

Display is not working. • Make sure the power cord is plugged in.

• Make sure the wall socket has power (check
by plugging another appliance in).

VCR will not operate -

appears in VCR

display.

• Press the TIMER ON/OFF button to
disengage timer.

VCR will not respond to
any commands.

• Check the CHILD LOCK is not engaged.

• Safety device operating: unplug VCR for 2
hours.

PLAYBACK No picture appears. • Make sure the TV is set to the video channel.

• Check all connecting cables.

Playback picture is
snowy.

• Adjust the tracking using the

VCR CHANNEL

/

buttons

.

• Try another tape.

• The video heads may have been
contaminated - refer to a SHARP Service
Facility.

Playback/Recording
does not play back in
Stereo

• Ensure the VCR is connected to a stereo TV
with a SCART lead.

• Programme may not carry stereo.

RECORDING Tape is automatically

ejected when pressing
the

REC

or

TIMER ON/OFF

buttons.

• The record-protection tab has been
removed from the cassette.

TINS-3992UMZZ English.book Page 34 Monday, June 4, 2001 9:28 AM

35

TROUBLESHOOTING

TROUBLESHOOTING

AREA PROBLEM POSSIBLE CAUSE/CURE

RECORDING VIDEOPLUS+ does not

record desired
programme.(VC­MH714HM only)

• Broadcast does not carry VPS/PDC signal
which alters recording time.

• Check VPS/PDC mode is switched ON.

• Ensure date and time are correctly set on the
VCR.

TAPE

TRANSPORT/

MECHANISM

Tape can not be
loaded.

• Make sure there is no other tape in the VCR.

• Make sure you are loading the tape
correctly.

Rewind is not
possible.

• Make sure the tape is not at the start.

REMOTE

CONTROL

The VCR can not be
operated by remote
control.

• Remote control is too far away from the main
unit.

• Point the remote control at the VCR.

• Batteries are flat - replace both.

• Batteries have not been inserted correctly.

• VCR is positioned in strong light.

OTHER

PROBLEMS

Picture does not
change even though
the VCR CHANNEL

/

buttons

are

pressed.

• Make sure the VCR is not in Timer or Menu
mode.

Desired channel
position can not be
selected.

• The channel position has been set to be
skipped. Cancel the SKIP mode for that
channel.

No colour or poor TV
picture on normal
viewing.

• Make sure all the cables are connected
properly.

• Make sure the VCR power cord is properly
plugged in.

Not possible to view
picture or playback
through RF OUT.

• Make sure the RF OUTPUT has not been
switched off. (Refer to page 36, RF CHANNEL
TUNING and RF THROUGH ON/OFF)

Desired channel has
interference.

• Possible weak signal strength, the same
channel with a better signal strength may
have been tuned in on another VCR preset
channel. Example;
VCR preset 1 = BBC1 and
VCR preset 14 = BBC1
(Refer to Manually Sorting Channels section
to move the channel to your desired
position.)

• TV aerial may need adjusting.

No picture appears. • Make sure the TV is on the video channel.

• Check all connecting cables.

TINS-3992UMZZ English.book Page 35 Monday, June 4, 2001 9:28 AM

36

www.sharp.co.uk/support

VCR RESET

1.

Press the

STOP

button on the front of the VCR.

2.

Press and hold

MENU

and

CHANNEL DOWN

buttons together on the

front of the VCR

for 10 seconds.

✔

VCR RESET IS NOW COMPLETE

Please continue with your previous procedure.

RF CHANNEL TUNING

If you have a preferred RF output channel this can be set manually between channels 21 and
69 by following the procedure below.

1.

Press the

STANDBY

button.

2.

Press and hold the

MENU

button for 3 seconds.

3.

Wait for a flashing channel number to appear on the VCR display.

4.

The channel number can now be changed by using the

VCR CHANNEL

/

buttons.

5.

Your TV will now require tuning to the new
channel. (The screen opposite should be
displayed on the TV)

6.

Press the

SET

button to store.

RF THROUGH ON/OFF:

If you wish to connect your VCR to the TV with only a scart lead, the RF Output on your VCR

can be turned OFF and ON. To do this press the

CLEAR

then

SET

buttons on the

remote control at point 3 from

RF CHANNEL TUNING

above.

or

at point 4 of

AUTO

TUNING

on page 5. This will help minimise interference.

STOP

VCR RF

SET : EN TER MENU : EX I T

SET

SET

(White text
blue background)

TINS-3992UMZZ English.book Page 36 Monday, June 4, 2001 9:43 AM

37

www.sharp.co.uk/support

GUARANTEE

SHARP Electronics (UK) Ltd. (hereafter called Sharp) guarantee to provide for
the repair, or at its option the replacement, of this product subject to the
conditions listed below:

1.

This guarantee shall only apply to faults which are due to inferior
workmanship or materials. It does not cover faults or damage by
accident, misuse, fair wear and tear, neglect, tampering with the
product, or repair other than by a Service Facility appointed by SHARP.

2.

As this product is intended for private domestic use only, the guarantee
will not apply if the product is used in the course of a business, trade or
profession.

3.

To benefit from this guarantee, any fault which occurs must be notified
to SHARP, or its appointed Service Facility within one year from the date
this product was purchased. Proof of purchase must be provided.

4.

The guarantee does not cover carriage costs, batteries or video tapes.

5.

In the unlikely event of this product requiring repair, please contact the
supplier from whom it was purchased. Where this is not possible, please
contact the SHARP Helpline on the telephone number given below.

6.

This guarantee is offered as an additional benefit to your statutory rights
and does not affect these rights in any way.

7.

No person has any authority to vary the terms or conditions of this
guarantee.

If you have any difficulty operating this product, or would like information on
other SHARP products, please telephone the SHARP Helpline on the number
given below.

In the unlikely event of this equipment requiring repair during the guarantee
period, you will need to provide proof of the date of purchase to the
repairing company. Please keep your invoice or receipt which is supplied at
the time of purchase.

SHARP Helpline: Tel: [phone] (office hours)
or [phone] if telephoning from Ireland

Please note that all calls are charged at local rate.

TINS-3992UMZZ English.book Page 37 Monday, June 4, 2001 9:43 AM

38

www.sharp.co.uk/support

CONNECTING TO THE MAINS

This VCR is suitable only for connection to UK
mains. The unit is fitted with a moulded 3-pin
mains plug with a 3-amp fuse. The VCR does not
have a mains power switch. When connected
to the mains, the unit will draw current at all
times to power the clock. Be sure to unplug the
VCR when it is not to be used for several months.

TO REPLACE THE FUSE:

You must use a 3-amp fuse, marked (ASTA) or (BSI) to BS-1362. Remove the fuse
cover as shown. Replace the fuse and re-fit the fuse cover securely into the plug.

Never connect the plug to the
mains without the fuse cover
fitted.

TO REPLACE THE MAINS PLUG:

If the plug fitted is unsuitable for the mains socket in your home, cut off the plug, remove the
fuse and dispose of the cut-off plug safely.

The wires in the mains cable are colour coded as follows: blue = neutral, brown = live.
As the colours of the wires may not correspond with the terminals in your plug, connect the
wires following plug manufacturer's guide:

• blue wire to the terminal marked N or coloured black or blue.

• brown wire to the terminal marked L or coloured red or brown.

Severe electric shock may occur if you connect the cut-off
plug to a mains socket. If a new plug is fitted, observe the
wiring code supplied by the plug manufacturer (and given
below.) If you have any doubt, consult a qualified
electrician.

• Ensure neither the brown nor the blue wire is connected
to the earth terminal in your plug.

• Do not allow water to come into contact with the power
supply cord or plug.

• A damaged power supply cord or loose plug may cause
electric shock.

• Contact your SHARP dealer or a qualified electrician. Do
not use the VCR.

ASA

TINS-3992UMZZ English.book Page 38 Wednesday, May 9, 2001 12:25 PM