Sharp SJ-58L-T2G, SJ-58L-T2A, SJ-63L-T2G, SJ-63L-T2A, SJ-63L-T2W Service Manual

1

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

SERVICE MANUAL

S8018SE60APR3

SHARP CORPORATION

REFRIGERATOR-FREEZER

In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.

TABLE OF CONTENTS

page

ENERGY LABEL.............................................................................................................................................. 2

INSTALLATION................................................................................................................................................ 2

CAUTIONS AND INFORMATIONS.................................................................................................................. 3

SPECIFICATIONS ........................................................................................................................................... 4

DESIGNATION OF VARIOUS PARTS............................................................................................................. 5

LIST OF ELECTRICAL PARTS........................................................................................................................ 6

THE FICHE ...................................................................................................................................................... 7

WIRING DIAGRAM .......................................................................................................................................... 8

FUNCTIONS .................................................................................................................................................. 10

ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS .............................................................13

MODIFICATION PROCEDURE OF THE DOOR OPEN SIDE ....................................................................... 21

COOLING UNIT ............................................................................................................................................. 24

REPLACEMENT PARTS LIST....................................................................................................................... 26

Refrigerant; HFC-134a

Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant.

DESTINATION ......................... 3

This equipment complies with
the requirements of Directives
96/57/EC,89/336/EEC and
73/23/EEC as amended by
93/68/EEC.

SJ-58L-

T2G/T2A

SJ-63L-

T2G/T2A/T2W

SJ-68L-

T2G/T2A

MODELS

2

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

INSTALLATION

Free standing type

To ensure adequate ventilation for this refrigerator, install with 6 cm space at the rear and both sides, with a
minimum space of 9 cm above the refrigerator.

This refrigerator shall be used under the ordinary place condition between +5˚C and +43˚C of ambient
temperature, and also not be left under -10˚C for long days.
To be used this refrigerator within the range of the rated voltage ±6%.

ENERGY LABEL

Usage of "the ENERGY LABEL"

When displaying this refrigerator in the shop-window, attach the
"ENERGY LABEL" to it in the following procedure.

"ENERGY LABEL (DATA)"
(This label is in Operation manual)

"ENERGY LABEL (BASE)"
of each language

Refrigerator

Data part

E

B

A

C

D

E

G

F

G

Fix the data part of
"ENERGY LABEL (DATA)"
on the data part of
"ENERGY LABEL (BASE)"

6cm 6cm

9cm

3

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

Some household cleaning chemicals may affect the internal
food liner and plastic parts resulting in splitting or cracks
occurring.
When cleaning all plastic parts inside this refrigerator, only
use diluted dishwashing liquid(soapy water). Make sure that
all plastic parts are thoroughly rinsed with water after cleaning.

CAUTIONS AND INFORMATIONS

1. Some foods freezed in the refrigerator compartment.

2. Some plastic parts were cracked or splitted.

Cracking or crunching sound;

Sound produced by expansion and contraction of inner walls and internal parts during cooling.

Squeaking sound;

Sound produced by expansion and contraction of internal parts.

Sound of flowing fluid (gurgling sound, fizzing sound);

Sound of refrigerant flowing in pipes (sound may become louder from time to time).

3. IT IS NORMAL for the refrigerator to produce the following sounds.

Do not place food directly in front of
cold air outlet.
This may lead to the food freezing.

IN
OUT

cold air flow

In case of following troubles, the cause is not related with the failure of refrigerator.
Please mention the correct way to the customer for the use of refrigerator when the repairing.

4

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

SPECIFICATIONS

Hole

Items SJ-58L-T2 SJ-63L-T2 SJ-68L-T2
Type 2-Door 2-Door 2-Door
Outer dimensions Height 1620mm(63.8") 1720mm(67.7") 1820mm(71.6")
(Including spacer) Width 760mm(29.9") 760mm(29.9") 760mm(29.9")

Depth 740mm(29.1") 740mm(29.1") 740mm(29.1")

Rated storage volume 492 liter (17.4 cu.ft) 535 liter (18.9 cu.ft) 577 liter (20.4cu.ft)

F: 151 liter (5.3 cu.ft) F: 151 liter (5.3 cu.ft) F: 151 liter (5.3 cu.ft)
R: 341 liter(12.1 cu.ft) R: 384 liter(13.6 cu.ft) R: 426 liter

(15.1 cu.ft)

Rated gross volume 525 liter (18.6 cu.ft) 565 liter (20.0 cu.ft) 610 liter (21.6 cu.ft)

F: 171 liter (6.1cu.ft) F: 171 liter (6.1cu.ft) F: 171 liter (6.1cu.ft)
R: 354 liter(12.5cu.ft) R: 394 liter(13.9cu.ft) R: 439 liter

(15.5cu.ft)

Defrosting System Heater system

Start Automatic

Finish Automatic
Temperature control Automatic (Adjustable)
No-frost freezer Yes
Interior lamp 2
Caster 4
Evaporating pan 1
Refrigerator R glass shelf ass'y 2 3
Compartment V glass shelf ass'y 1

Vegetable case 1

Fruit case 1

R door pocket 1 2

Egg tray 2

Bottle pocket 2

Utility case pocket 1

Chilled case 1

Tube stand 2
Freezer Freezer shelf ass'y 1
Compartment Ice cube maker Twin ice cube maker

Ice storage box 1

F door pocket 2
Deodorizing system No

RATING

Items SJ-58L-T2 SJ-63L-T2 SJ-68L-T2
Rated voltage (V~) 220-240
Rated frequency (Hz) 50
Climate class T
Rated input (W) 170-190
Rated input of heating elements (W) 138-164
Refrigerant (Charging quantity) HFC-134a(120g) HFC-134a(125g) HFC-134a(130g)
Net Weight (kg) 81 83 88
Plug cord 3wires
Plug type CS

COLOR

Items T2G T2A T2W
Outside color Gray Beige White
Inside color White

OPTIONAL ITEM

SJ-L838LD (REFRIGERATOR HINGE KITS). For changing the door to left side opening.

5

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

DESIGNATION OF VARIOUS PARTS

The names are the denominations used in the
REPLACEMENT PARTS LIST.

1. Freezer light(Lamp)

2. Freezer fan

3. Freezer shelf(F shelf ass'y)

4. Ice cube maker

5. Ice cube box(Ice storage box)

6. Freezer temp. control knob

7. Chilled case

8. Refrigerator temp. control knob

9. Refrigerator fan

10. Refrigerator light(Lamp)

11. Refrigerator shelf(R glass shelf ass'y)
(SJ-58L/ SJ-63L; 2 shelves, SJ-68L; 3 shelves)

12. Shelf(V glass shelf ass'y)

13. Fruit case

14. Vegetable crisper(Vegetable case)

15. Evaporating pan & cover

16. Caster

17. Adjustable feet(Adjustable leg ass'y)

18. Fan & light switch(for freezer)

19. Fan & light switch(for refrigerator)

20. Freezer pocket(F door pocket)

21. Water cup

22. Magnetic door seal(Door packing)

23. Utility pocket(Utility case pocket)

24. Egg holder(Egg tray)

25. Free pocket(R door pocket)
(SJ-58L/63L; 1 pocket, SJ-68L; 2 pockets)

26. Bottle pocket

27. Bottle guard(Tube stand)

1

18
19

20
21

22
23

24
25

26

27

3

2

4
5

6
7

8
9

10
11
12

13
14

17

15
16

22

Figure D-1. External Description

Figure D-2. Constructions

Upper hinge cover

Hot pipe

Freezer temp. control knob

Hot pipe

Ventilating grille

Evaporating pan

Adjustable leg ass’y

Fan motor

Freezer fan

Defrost thermostat
Evaporator
Defrost heater

Damper thermostat
Refrigerator temp. control knob
Drain pipe

Vegetable case
Compressor

Starting relay, Overload relay(Protector)

Caster

Sub. condenser

Freezer
compartment

Refrigerator
compartment

Fruit case

Mark: Cold air flow

Timer, R-fan themo. ass’y
Refrigerator fan

This figure shows SJ-63L

6

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

+

+

Common

Main coil

Aux. coil

Common

Main coil

Aux. coil

LIST OF ELECTRICAL PARTS

ITEMS TYPE NAME RATING SPECIFICATIONS
Thermostat MM1-8123 125V 6A (At normal notch)

250V 3A ON/OFF : -19/-24˚C
Defrost thermostat S101 250V 8A Open/Close : 10/1˚C
Thermo. fuse SF70E 250V 10A Working temp. : 70˚C
F-fan motor 3R00044B 220-240V 50/60Hz Working with ø100 fan
R-fan motor 3R00122A 220-240V 50/60Hz Working with ø80 fan
(R-fan fuse) 123 250V 2A Cut OFF 130˚C
Defrost heater MM6-4198 220-240V 353Ω 150W at 230V
Door switch DSD-5 250V 0.25A 4 terminals push-button type
Damper thermostat MM1-6170

(SJ-63L/68L)

— Open/Close : 3/-2˚C

MM1-6171

(SJ-58L)

— Open/Close : 5/0˚C
Defrost timer TMDF904FD2 220-240V Integration type

50/60Hz Cycle time : 10.8/9.0 hours(50/60Hz)

Delay time : 4.3/3.6 min.(50/60Hz)
Lamp socket (F/R) — 250V 1A E-12(Hard plastic body type)
F-lamp — 240V 10W E-12
R-lamp — 240V 15W E-12
R-fan thermo. R-fan thermo.

S101 250V 8A Open/ Close : 7/15˚C

ass'y

R-fan thermo.heater

RSS2 350V, 2W, 10kΩ 1.1W at 230V

SJ-58L,63L
Compressor GLY80AA 220-240V/50Hz Cooling capacity : 197kcal/h(50Hz)

Main coil : 10.3Ω

Aux. coil : 14.2Ω

(at 25˚C)

Starting relay UH3003-7 — 14.0 Ω 30%
Runnig capacitor — 430VAC 5µF—
Overload relay(Protector) 4TM308NFBYY — Open/ Close : 120/61˚C

SJ-68L
Compressor GLY90AA 220-240V/50Hz Cooling capacity : 220kcal/h(50Hz)

Main coil : 8.8Ω

Aux. coil : 14.2Ω

(at 25˚C)

Starting relay UH3003-7 — 14.0 Ω 30%
Runnig capacitor — 430VAC 5µF
Overload relay(Protector) 4TM757NFBYY — Open/ Close : 120/61˚C

7

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

1

NO.

2
3

4
5
6

8

9

11
12
13
14

Trade mark

Items

Description

Remarks

Model name
Type

Energy efficiency class
Eco-award mark
Energy consumption

(220V 50Hz at 25 C)

Star rating of frozen food
compartment

Temperature rise time
Freezing capacity
Climate class
Noise

10 No frost

7

Net storage volume of fresh
frozen food storage compartment

SJ-58L-T2

Category; 7
Refrigerator/Freezer

B

TT

41 dB(A)
re 1 pw

41 dB(A)
re 1 pw

675

kWh/year

942

kWh/year

989

kWh/year

341 L

151 L

4-STAR

No frost

10 h

8 kg /24h

Net storage volume of fresh
food storage compartment

SJ-63L-T2

Category; 7
Refrigerator/Freezer

B

705

kWh/year

384 L

151 L

4-STAR

10 h

8 kg /24h

880/92
EN153

86/594/EEC
dB(A) re 1 pw

No frost

THE FICHE (according to ANNEX : 94/2/EC)

T

41 dB(A)
re 1 pw

1033

kWh/year

SJ-68L-T2

Category; 7
Refrigerator/Freezer

B

734

kWh/year

426 L

151 L

4-STAR

10 h

8 kg /24h

No frost

15

Maximum allowable electricity
consumption (Emax)

(96/57/EC)

8

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

WIRING DIAGRAM

Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set.

Figure W-1. Wiring Diagram



F-THERMOSTAT

(R)

DEFROST
TIMER

TM

THERMO.
FUSE

FMFM

DEFROST
HEATER

DEFROST
THERMOSTAT

STARTING
RELAY

C

M

A

COMPRESSOR

PROTECTOR

(B)

DOOR SWITCH

1

2

4

(S-B)

R-FAN THERMO.
HEATER

R-FAN
THERMO.

L

L

3

(O)

(BR)

(W)

(Y)

(G)

4

12

3

CONNECTED IN TERMINAL BOX
CONNECTOR

G
Br
O
Y
R
P
B
Bk
S-B
G-Y
W

: GRAY
: BROWN
: ORANGE
: YELLOW
: RED
: PINK
: BLUE
: BLACK
: SKY-BLUE
: GREEN-YELLOW
: WHITE



R

R

F

F

(BK)

SOURCE CORD

RUNNING
CAPACITOR

9

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

Figure W-2. Electric Accessories Layout

F LAMP BOX ASS’Y

F-LAMP(10W)

L

LAMP SOCKET

CABINET ASS’Y

E. V. COVER ASS’Y

LEAD EV-COVER ASS’Y

F-FAN MOTOR

F-THERMOSTAT

DEF. THERMO. ASS’Y

FUSE ASS’Y

FM

DEF. HEATER ASS’Y

DOOR SWITCH

3 (PUSH CLOSE)
1 (NEUTRAL)
4 (PUSH OPEN)
2 (PUSH OPEN)

TM

FM

R CONTROL COV. ASS’Y

DEFROST TIMER

(R-FAN
THERMO. HEATER)

R FAN THERMO.

R LAMP BOX ASS’Y

L

R-FAN MOTOR

R-LAMP (15W)

LAMP SOCKET

STARTING
RELAY

PROTECTOR

1
2
3
4

3
1
4
2

5
7

6
8

1
2

121

2

121

2

3
4

1
2
3
4

1

2

3

4

1

2

3

4

1
2
3
4

1
2
3
4

1
2
3
4

5
7

6
8

99

GY-1

(OR-1)

BL-2
SB-1

SB-2

SB-3

BR-3

BR-4

OR-3
OR-2

(OR-2)

(W-2)

OR-1

OR-3

R-1

BR-2
Y-1

(R-1)
(BK-1)

GY-2
(Y-1)
(Y-2)

BL-1
BK-1
W-1

BR-1
W-2

(W-1)

Y-2

TERMINAL BOX

C

M

A

BROWN

RUNNING CAPACITOR

BLUE

GRAY

SKY-BLUE

SOURCE CORD

TERMINAL COVER

COMPRESSOR

EARTH

1
L
E
N

10

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

FUNCTIONS

1. ADJUSTABLE TEMPERATURE CONTROL
(1) Temperature control of freezer

Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and
cool air circulating fan (F-fan motor) , and allows the freezer temperature to keep at a suitable temperature.
However adjust the freezer temp. control knob as follows depending upon the storing condition of foods.

MIN

MAX

MED

1

2

3

4

5

6

7

Coldest

FREEZER TEMP. CONTROL

MIN

MED

1

2

3

4

5

6

7 Coldest

CHILLED
ZONE

REFRIGERATOR TEMP. CONTROL

The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom
at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no
food stored and the door closed until the temperature is stabilized.
The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored
foods and manner of storing foods.

Figure F-1.

(2) Temperature control of refrigerator

Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper
automatically.
However, as the Damper-thermostat has no function to switch on or off the compressor and F-fan motor,
the freezer temperature control causes temperature in the refrigerator to vary to some extent.
However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition.

KNOB
SETTING

MAX

(Coldest)

MIN

PURPOSE

For making ice rapidly or fast freezing.

For storing frozen food for a short period (up to one month).
When frozen food or ice cream is not stored.

For normal freezing.

MED

When restocking with fresh food.

KNOB
SETTING

MED

CHILLED
ZONE
(Coldest)

MIN

PURPOSE

For keeping freshness of food longer.

For normal operation.
When the refrigerator provides excessive cooling.

When the refrigerator does not provide sufficient cooling.

Figure F-2.

When the temperature of the refrigerator is higher, R-fan thermo. senses the temperature and the
refrigerator is cooled efficiently by running of R-fan motor.
R-fan thermo. heater energizes when the door is opened intend to promote to running of R-fan motor.

NOTE: The refrigerator temperature is affected also by the freezer temperature. If the freezer temp.

control knob is set at the position "MAX", the temperature tends to be lower than the following
values, and if set at near the position "MIN", temperature tends to be higher.
If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX"
position, foods stored in the refrigerator compartment may also freeze.
When refrigerator temperature control sets to the "CHILLED ZONE", some foods stored may
freeze.
In this case adjust control set back to the "MED" position.
When refrigerator temperature control sets to the "CHILLED ZONE", some foods stored in chilled
case may also become frozen.

(3) Reference value of temperature

SETTING OF
FREEZER TEMP.
CONTROL KNOB

Freezer
temperature

MAX

(Coldest)

MED MIN

Approx.

-21 C

Approx.

-18 C

Approx.

-15 C

SETTING OF
REFRIGERATOR TEMP.
CONTROL KNOB

Refrigerator
temperature

Chilled room
temperature

CHILLED

ZONE

(Coldest)

MED MIN

Approx.

0 C

Approx.

-3 C

Approx.

3 C

Approx.

1 C

Approx.

6 C

Approx.

4 C

The values shown above refer to the case where the
freezer temp. control knob is set at "MED".

11

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(2) Where is melted frost brought

1. Melted frost is brought into the evaporating
pan at the bottom of the set and is evaporated
here by the heat of sub condenser.

2. Be sure that the evaporating pan is inserted
correctly and is level.

2. DEFROSTING
(1) No defrosting operation is necessary

No defrosting operation is necessary.
As this machine is so designed that a built-in
evaporator cools air and a fan circulates cooled
air, neither the freezer nor the refrigerator is
frosted, though the evaporator is frosted.
The frosted evaporator is defrosted automatically
due to the function of defrosting timer and heater,
requiring no defrosting operation.

(3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with

timer and defrost thermostat.

Operation Electric diagram Description

1. Cooling
(Normal)

2. Defrosting

(Time 20 to 30 min.)

3. Drain

(Time approx. 5 min.)

4. Restart

(Time approx. 5 min.)

The integration timer integrates running
time of the compressor. When it reaches
cycle time of defrost timer, the timer
contact is changed to start defrosting.

When the defrost thermostat becomes
OFF, the timer motor starts running.
During the operation time (delay time
of defrost time)

defrosted water is

drained outside the refrigerator.

Timer contact is changed to cooling
operation and the compressor starts
running and the timer motor stops.
Defrost thermostat contact becomes ON
when it’s cooled. And the timer motor
starts running. (Figure F-3.)

Figure F-3.

Figure F-4 .

Figure F-5.

Figure F-6.

TM COMP

Defrost thermostat ON Compressor running

Timer motor running

Timer contact

Defrost
thermostat (ON)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat OFF Compressor running

Timer motor stops

Thermostat Timer contact

Defrost
thermostat (OFF)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat OFF Compressor stops

Timer motor running

Thermostat Timer contact

Defrost
thermostat (OFF)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat ON Compressor stops

Timer motor stops

Thermostat Timer contact

Defrost
thermostat (ON)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

Thermostat

The timer contact is changed to start
defrosting, the timer motor stops, and
power is supplied to the defrost heater.
It takes about 20 to 30 min. to defrost.
When little frosted, the defrosting takes
little time. When much frosted, the def­rosting takes much time.

12

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(4) As a reference to determine the causes of trouble, malfunction and phenomena are described below.

Refer to the following when repairing.

1. Disconnection of defrost heater

As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is
started, the freezer temperature rises and a portion of ice and stored foods are melted.

2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat.

When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting
will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer
shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops
from the time when the contact is changed, and freezing causes.

NOTE:

As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even
for a short period.

3. DEW PREVENTION

The hot pipe, namely D.P.-condenser, is arranged around the flange part of
cabinet and the C-partition plate, preventing dew from being generated on
the cabinet.

NOTE:

D.P.-condenser pipe may be felt hot if touched by hand while the
compressor is in operation.
If you are asked about this, please explain that the hot pipe serve to
prevent the dew generation.

Figure F-7

4. INSPECTION OF INITIAL STARTING
(1) Inspection of cooling unit

1. Set the temperature control knob to "MAX" and check that the compressor starts to operate.

2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the
freezer and the refrigerator.

3. When the compressor does not work, check that the timer is not set to "defrost" position.

4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation.

NOTE:

After return the temperature control knob to "MED" position.
When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2
min. However, vibration becomes normal if it is continuously operated.

(2) Inspection of defrost device

Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures :
Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation.

1. Turn the timer shaft clockwise with a screw driver.
At this time, make certains the timer clinks and the compressor stops.

2. After more than 5 min., turn the shaft further to operate.
Make certain cooling operation is started again.

Hot pipe

13

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS

CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING.

1. R-CONTROL COV. ASSEMBLY

R-temp. control knob

Nylon band

Fan cover

R-C box cover

RA sealer B

RA sealer C

Dial sealer

RA sealer D

R air guider A

RA sealer A

Damper thermo.

A sealer thermo. cap.

Defrost timer

R fan thermo. ass’y

Figure A-1

After forming, fix it to the refrigerator.

Stick thermo.
cap. sealer

Less than 130 mm

Damper
thermostat

3

1

mm

5

1

mm

Less than 12 mm

25 2 mm

NOTE
Minimum bending radius is R5mm.
There should be no gas leak by reforming of sensor tube.

+

++

Figure A-2

(1) Forming sensor of Damper thermo.

14

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(2) Sticking of sealers to R air guider A.

RA sealer A

RA sealer A

RA sealer A

RA sealer CRA sealer B

A sealer
thermo. cap.

A sealer
thermo. cap.

RA sealer D

RA sealer A

RA sealer ARA sealer A

[Front side]

[Back side]

[Bottom side]

Dial sealer

OVERLAP 15mm

OVERLAP 15mm

Figure A-4

10 5mm

+

Cut

R-C box cover

Nylon band

R fan thermo ass’y

Fan cover

Defrost timer

R fan thermo.
ass’y

Nylon band

SEC. G-G

G

G

(3) Fixing of Defrost timer, R fan thermo. ass'y cover to R-C box cover.

Figure A-3

15

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

2. R LAMP BOX ASSEMBLY

Lamp socket (with lead wires for R-fan motor)

Lamp 15W

Warning label

R lamp box

Propeller fan 80

R-fan motor

R fan motor holder A

Fan clamp

R fan motor holder B

Figure A-5

(1) Fixing of Lamp and Lamp socket.

(1)-1 Screw Lamp 15W into Lamp socket.
(1)-2 Fix Lamp socket on R lamp box by tapping

screws.

Tapping screw

Lamp socket

Lamp 15W

R lamp box

ALUMINUM TAPE

Figure A-6

(1)-3 Insert the terminal of Lamp socket to R-fan motor.

Figure A-7

Fan motor

Lamp socket

DOUBLE CLAMPING WIRES

16

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(2) Fixing of R-fan motor and Fan

(2)-1 Set R-fan motor holder A to R lamp box by

tapping screw.

(2)-2 Set R-fan motor to R fan motor holder A by

machine screw.

(2)-3 Set R fan motor holder B to A.

Propeller fan 80

R fan motor holder A

R-fan motor

R fan motor holder B

Fan clamp

Propeller fan 80

F

Shaft

2.3 0.5mm

+

Fan clamp

Slit

Slit of each Fan clamp and Propeller fan
should not be at same position.

Detail of F

(2)-4 Set Fan clamp to Propeller fan 80 and insert it

to the shaft of R-fan motor.

Figure A-9

(3) Sticking Warning label.

Figure A-8

Lamp 15W

Warning label

Figure A-10

17

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

3. E.V COVER ASSEMBLY

Defrost thermo. ass’y

E.V cover

E.V cover
sealer D
(2 pieces)

F-thermostat

L-band C

E.V cover sealer A

Fuse ass’y

E.V cover sealer B

E.V cover sealer C

Lead E.V-cover
ass’y

Fan motor
holder A

Fan motor
holder B

Propeller Fan 100

Fan clamp

Motor
cushion

U-sealer
handle

Fan motor

Figure A-11

Figure A-12

(1) Sticking of Sealers to E.V cover

E.V cover sealer B

E.V cover sealer D (b)

E.V cover sealer D (a)

E.V cover sealer A

E.V cover

Sticking start (b)

Sticking start (a)

Sticking start

Overlap 10mm(min)

[Front side] [Back side]

Sticking start

18

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(2) Fixing of Fan motor and Fan

(2)-1 Stick U-sealer handle to Fan motor holder A.

Fan motor holder A

U-sealer handle

U-sealer handle

7 2mm

+

+

0 1mm

C

C

SEC. C-C

Figure A-15

Figure A-13

(2)-4 Set Fan clamp to Propeller fan 100 and insert

it to the shaft of Fan motor.

Fan clamp

Propeller
fan 100

Fan clamp

Slit

Slit of each Fan clamp
and Propeller fan
should not be at same position.

Shaft

4 0.5mm

+

Detail of D

D

(2)-2 Insert the terminals of Lead EV-cover ass'y to

R-fan motor.

(2)-3 Fix two Motor cushions to R-fan motor, and set it

at Fan motor holder A and B.
Then fix with Tapping screw.

Fan motor
holder A

Fan motor
holder B

Motor cushion

Tapping
screw

Fan motor

Lead EV-cover ass’y

RED

BROWN

Figure A-14

19

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y

After inserting, fix with vinyl tape.

60mm

Vinyl tape

(4) Inserting of pins

Aluminum
tape

Aluminum
tape

Turn up is lead wire

ATTENTION

cut

10 5mm

+

Tapping screw

Tapping
screw

E.V cover

E.V cover
sealer C

E

E

L-band C

L-band C

Defrost thermo.
assembly

Defrost thermo.
assembly

Set metal side below

F

F

Fuse assembly

E.V
cover

Fuse
ass’y

Lead E.V­cover ass’y

Sec. F-F

Sec. E-E

Not come out of claw

Take out lead wire from
square hole to front, and
seal with E.V cover sealer C.

[FRONT SIDE]

more than

3.5mm

more than

3.5mm

Figure A-16

Figure A-18

123

456

789

F-thermostat 3

F-thermostat 4

Fuse 8

Fuse 7

Fan motor 1 , 2

Fan motor 9

(RED, inserted)

(BROWN, inserted)

(WHITE)

Defrost thermo. 5

Defrost thermo. 6

(PINK)

(BLUE)

(BLACK)

WIRE COLOR FOR FAN MOTOR

100-110V : WHITE

127V : YELLOW

220-240V : BLUE

Note Pins should be inserted surely,
and check by pulling it.

Figure A-17

20

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

(5) Setting of F-thermostat

(5)-1 Form capillary tube of F-thermostat.

42mm13mm

20mm

20mm

230mm

R10mm

R10mm

Note

• Bending radius of
capillary tube should be

from R5mm to R10mm.

Figure A-19

F

F

SEC. F-F

(5)-3 Set to E.V cover.

Figure A-21

(5)-2 Insert terminal of Lead EV-cover ass'y.

RED

BROWN

(front side)

(back side)

Figure A-20

21

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

Tools required

Parts list

Phillips and slotted screwdrivers
Drill bit ( 3.8 mm)
Socket wrench or spanner (8 mm) :The socket wrench or spanner is used to detach and attach hinges.

Always disconnect the power plug from the wall outlet before performing work.
Caution should be taken when handling the doors.
These are heavy and could cause personal injury if mishandled.
Always tighten screws securely. May cause personal injury if door becomes unlatched and falls.
Reattach doors paying careful attention to the door alignment. Failure to fit the door
correctly might cause the cool air to leak out and lower the cooling performance.

Caution

Fitting Instruction

AB

C

D

E

F

G

HJ

Stopper spring L
(for upper door)

Stopper spring L
(for lower door)

Bottom hinge L

Door cap cover
(for upper door)

Door cap cover
(for lower door)

Door hole cover

Screw and Cover

Silicon grease

Preparation/Removing Doors

1

1. Remove Evaporating pan cover, Upper hinge cover, and Top cover.

(Carefully remove Upper hinge cover using a screwdriver, making sure that the door is not damaged.)

2. Remove Upper hinge and Spacer, and detach Upper door by lifting off the center hinge.

3. Remove Center hinge and detach Lower door by lifting off the bottom hinge. Remove the 2 Hole caps, replace them on
the screw holes of the removed center hinge, then screw in G (screw and cover) in the center hole.

4. Remove Bottom hinge. Remove the 3 screws on the left side, then install them in the screw holes of Bottom hinge.

1

Select the same color as the refrigerator exterior.

G

4

4

3

3

1

1

2

3

1

2

3

G

Screw cap for handle
(Spare)

Figure M-1

MODIFICATION PROCEDURE OF THE DOOR OPEN SIDE

It is possible to change the door to left side opening.
To modify the door to left side opening, REFRIGERATOR HINGE KITS (for left side opening) SJ-L838LD (optional item )is necessary.

by SJ-L838LD OPERATION MANUAL

These kits are used to change the refrigerator doors from right to left opening.
if you wish to change the door to left opening for some reason, such as restricted installation
space, ask your authorized service agent for this modification.

22

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

1. Remove Screw caps and Screws on each door handle, then remove the handles.
Flatten the surface of the screw holes using the handle of a screwdriver, etc., then mount 3 units of F (Door hole covers)
on each door.

2. Remove the Nylon bearings, Door stopper(Lower door only), Stopper springs on the right side of each door and the cap
on the left side of the Upper door. Furthermore, open the hidden holes on the bottom of the door using a screwdriver,
then remove a screw (Lower door only).

3. Remove Screw caps and Screws on the right side of each door, then remove the Door cap covers and mount D and E
(Door cap covers) on the left side.

4. Replace Nylon bearings to the left side of each door, then mount the Upper door cap on the right side. Furthermore,
mount Door stopper and B and C(Stopper springs) on the left side as well. Screw in a screw in the screw hole on the
lower right of the Lower door.

5. Fix upper portion of Upper handle using one screw on the right side of Lower door, then temporarily fix the handle to the
door using tape.

6. To open screw holes, first make marks on the doorplate surface through the 3 holes of the handle, then temporarily
remove the handle (make sure that the dimensions of the markings are as shown in the diagram).

7. Lightly dent the center of each marking, then open holes using a 3.8 mm drill bit.
Use a drill guide, etc., to prevent the drill bit from entering more than 5 mm.
Make sure to open the hole straight. Opening the hole in an angle will cause the handle to clatter.
The door will be unusable if the hole are too large or too deep or if the screws are tightened too much.

8. Mount the handle using the 4 screws and install Screw caps.

9. Mount Lower handle on the right side of Upper door by repeating steps 5. ~ 8. above.

Replacing Handles and Door Parts

2

F

172mm

5mm

172mm

27mm

16mm

F

D

B

C

E

5-8

9

4

4

2

3

3

4

2

2

5,6

7

8

4

2

3

3

1

1

1

1

2

4

2

2

2

(J)

Figure M-2

23

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

Mounting the Door/Finishing

1. Apply Silicon grease H to the shaded portion of part A(Bottom hinge L) and attach it to the left side.

2. Insert Lower door and fit Center hinge vertically inverted. Remove washer if installed. Tighten the screws temporarily.

3. Fit Upper door and attach Upper hinge together with spacer. Tighten the screws temporarily.

4. Adjust the alignment of the door. Ensure that the gap between the cabinet and door is 12 mm. Tighten the upper hinge

screws.

5. Secure Upper door. Open Lower door and tighten the center hinge screws. (No drawing)

6. Check the following. To readjust the door position, loosen Center and Bottom hinges.

Whether the distance to activate the door switch is correct.
Whether each door can be opened/closed smoothly.
Whether each door is properly sealed when closed. (Check by inserting a sheet of paper between the door and
cabinet when closing. The refrigerator is not properly sealed if the paper falls.)

7. Apply Silicon grease H to the shaded portion of the door packing.

8. Replace the cap in Evaporating pan cover on the right side.

9. Reattach Evaporating pan cover, Upper hinge cover and Top cover.

10. Make sure that each door can be opened and closed normally. (If any of the doors cannot open/closes normally, tilt the

refrigerator slightly backward by screwing out the two adjustable feet.) Furthermore, connect the power plug, make sure
that cold air is not leaking from the door packing, and that the cabinet lamp operates properly when the door is
opened/closed.

Retain removed parts in case doors are to be changed back to right opening.

3

3

12mm

A

2 1.0mm

3

9

4

6

2

7

1

2

1

9

8

9

2

3

3.5 0.5mm

+

+

Figure M-3

24

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

COOLING UNIT

Figure C-1. Cooling unit

Hot pipe L
(Side condenser)

Hot pipe
(DP-condenser)

Hot pipe R
(Side condenser)

Evaporator

Suction pipe

Sub. condenser

Compressor

Capillary tube

Dryer

Back condenser

Mark: Refrigerant flow
Mark: Brazing portion

25

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

Charge pipe L
to Dryer

Hot pipe
to Dryer

Pinch Point

Compressor’s discharge pipe
to Sub. condenser

Back condenser to
hot pipe

Pinch point

Suction pipe to
Compressor’s suction pipe

Suction pipe to
S.P connector

Dryer
to Capillary tube

Sub. condenser to
Back condenser

Charge pipe L to
Compressor’s process tube

Compressor butyl

Figure C-3. Location

Figure C-2. Location

Compressor

Suction pipe

Charge pipe

Charge pipe

Capillary tube

Dryer

Hot pipe

S.P. connector

Sub. condenser Back condenser

Evaporator

26

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

REPLACEMENT PARTS LIST (SJ-58L/63L/68L-T2G)

ELECTRIC PARTS

1-1 RTHM-A097CBEZ F-thermostat 1 1 1 AX
1-2 RSTT-A144CBE0 Starting relay 1 1 1 AW
1-3 QSWTDA035CBE0 Defrost timer 1 1 1 BB
1-4 PDMP-A046CBEZ Damper thermo - 1 1 AX
1-4 PDMP-A048CBEZ Damper thermo 1 - - AW
1-5 FTHM-A028CBKZ Defrost thermo.ass’y 1 1 1 AN
1-6 RMOTRA040CBE0 Fan motor 1 1 1 AZ
1-7 QSOCAA074CBEZ Lamp socket 1 1 1 AP
1-8 RLMP-A012CBE0 Lamp 1 1 1 AH
1-9 QACC-A097CBE0 Source cord 1 1 1 AV
1-10 QSW-PA090CBZA Door switch 1 1 1 AS
1-11 RHOG-A084CBE0 Protector 1 1 - AN
1-11 RHOG-A105CBE0 Protector - - 1 AV
1-17 FFS-TA055CBKZ Fuse ass’y 1 1 1 AL
1-20 FW-VZA144CBEZ Lead ev-cover ass’y 1 1 1 AK
1-21 FHETBA146CBEZ Def.heater ass’y 1 1 1 AZ
1-22 FCNW-A622CBK0 Relay wire ass’y 1 1 1 AN
1-23 QCNW-A671CBE0 Relay wire rc 1 1 1 AD
1-25 QTAN-A032CBE0 Terminal block 1 1 1 AE
1-27 RMOTRA061CBEZ Fan motor 1 1 1 AW
1-28 RLMP-A029CBEZ Lamp15w 1 1 1 AH
1-29 QSOCAA072CBEZ Lamp socket 1 1 1 AN
1-30 FTHM-A029CBKZ R fan thermo ass’y 1 1 1 AQ
1-32 RC-EZA190CBEZ Running capacitor 1 1 1 AW

MECHANICAL PARTS

2-2 JKNB-A036CBFB F-temp. control knob 1 1 1 AD
2-4 LPLTMA568CBEZ Fl plate al. 1 1 1 AF
2-7 FLEGPA077CBKZ Leg holder l ass’y 1 1 1 AQ
2-7-1 FAJS-A009CBK0 Adjustable leg ass’y 2 2 2 AD
2-7-2 LHLD-A533CBPZ Leg holder l 1 1 1 AL
2-8 FLEGPA078CBKZ Leg holder r ass’y 1 1 1 AQ
2-8-2 LHLD-A534CBPZ Leg holder r 1 1 1 AP
2-10 PSPAVA083CBEA Upper hinge spacer 1 1 1 AD
2-11 PSPAVA084CBEA Bottom hinge spacer 1 1 1 AC
2-12 PSPAVA075CBEA Center hinge spacer 1 1 1 AD
2-13 DHNG-A363CBMZ Upper hinge ass’y 1 1 1 AE
2-14 DHNG-A365CBMZ Bottom hinge r ass’y 1 1 1 AE
2-15 DHNG-A364CBMZ Center hinge r ass’y 1 1 1 AF
2-16 GCOV-A191CBFZ E.v cover 1 1 1 AS
2-17 LCRA-A010CBE0 Fan clamp 2 2 2 AD
2-19 LHLD-A389CBF0 Motor cushion 2 2 2 AF
2-20 NFANPA020CBFA Propeller fan 100 1 1 1 AE
2-21 PSEL-B845CBEZ E.v cover sealer a 1 1 1 AC
2-22 PSEL-B846CBEZ E.v cover sealer b 1 1 1 AC
2-23 PSEL-A415CBE0 E.v cover sealer c 1 1 1 AC
2-24 PCOVPA164CBFA Terminal cover 1 1 1 AE
2-25 PCOV-A253CBFA F lamp cover 1 1 1 AC
2-26 PCOV-A254CBFA R lamp cover 1 1 1 AF
2-27 GCOVPA119CBRA R-cbox cover 1 1 1 AS
2-28 HGRL-A184CBRA Fan louver 1 1 1 AU
2-29 GCOV-A162CBFG Upper hinge cover 1 1 1 AD
2-30 PCOV-A255CBFA Fan cover 2 2 2 AD
2-31 JKNB-A033CBFB R-temp.control knob 1 1 1 AD
2-36 PCAP-A006CBFX Screw cover 2 2 2 AB
2-37 PCAP-A056CBFF Screw cover b 2 2 2 AC
2-38 PGID-A156CBFZ R air guider a 1 1 1 AG
2-41 PSEL-B848CBEZ A-sealer thermo.cap 1 1 1 AC
2-49 LSTPPA108CBFA Chilled stopper 2 2 2 AC
2-50 NFANPA019CBFA Propeller fan 80 1 1 1 AM
2-51 PBOX-A121CBFA F lamp box 1 1 1 AF
2-52 PBOX-A122CBFA R lamp box 1 1 1 AM
2-53 LHLD-A536CBFA R fan motor holder a 1 1 1 AF
2-54 LHLD-A537CBFA R fan motor holder b 1 1 1 AE
2-55 HGRL-A181CBFA Multi louver l - - 1 AN
2-55 HGRL-A186CBFA Multi louver m - 1 - AM
2-55 HGRL-A188CBFA Multi louver s 1 - - AG
2-56 PFPFPB233CBFZ R-louver insu. l - - 1 AG
2-56 PFPFPB239CBFZ R-louver insu. m - 1 - AF
2-56 PFPFPB248CBFZ R-louver insu. s 1 - - AE
2-57 PSEL-B843CBEZ A-sealer r-louver - - 2 AC
2-57 PSEL-B857CBEZ A-sealer r-louver - 2 - AC
2-57 PSEL-B861CBEZ A-sealer r-louver 2 - - AC

SJ-58L SJ-63L SJ-68L

-T2G -T2G -T2G

27

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

2-59 PCOV-A264CBEZ F lamp box cover 1 1 1 AC
2-63 LHLD-A484CBFA Fan motor holder b 1 1 1 AH
2-64 LHLD-A485CBFA Fan motor holder a 1 1 1 AH
2-65 PSEL-B209CBE0 U-sealer handle 2 2 2 AB
2-66 PSHEMA132CBP0 Heater cover al 1 1 1 AD
2-67 LPLTMA570CBPZ Drain support al 1 1 1 AE
2-69 PSEL-B847CBEZ E.v cover sealer d 2 2 2 AC
2-71 PSEL-A552CBE0 Dial sealer 1 1 1 AC
2-72 PSEL-B841CBEZ Ra sealer a 2 2 2 AC
2-73 PSEL-B842CBEZ Ra sealer b 1 1 1 AC
2-74 PSEL-B122CBE0 A-sealer thermo.cap. 1 1 1 AB
2-77 LHLD-A391CBE0 Sl-5n clip 1 1 1 AD
2-78 LPLTMA399CBP0 Dryer support 1 1 1 AD
2-79 LBND-A019CBE0 Nylon band 3 3 3 AB
2-80 PBOX-A071CBFA Terminal box 1 1 1 AE
2-81 PPIPPA097CBEZ Drain pipe s 1 1 1 AE
2-83 PSEL-B849CBEZ Ra sealer c 1 1 1 AC
2-84 PSEL-B850CBEZ Ra sealer d 1 1 1 AC
2-87 LBND-A018CBE0 Fastening band a 1 1 1 AP
2-90 HGRL-A179CBFA F shower duct 1 1 1 AM
2-91 HGRL-A180CBFA F return cover 2 2 2 AC
2-93 PCAP-A068CBFA C sliding cap a 2 2 2 AC
2-95 NROL-A027CBEZ V roller 2 2 2 AC
2-96 LHLD-A535CBFA Shaft holder 2 2 2 AC
2-97 LPIN-A178CB1Z Shaft 2 2 2 AC
2-99 GCOV-A192CBFA Top cover 1 1 1 AC
2-105 PSEL-B896CBEZ A-sealer fs-a 1 1 1 AC
2-106 PSEL-B897CBEZ A-sealer fs-b 2 2 2 AC

DOOR PARTS

3-5 FDORFB299CBKZ F-door ass’y 1 1 1 BK
3-5-1 LSTPPA107CBFA Fd stopper spring r 1 1 1 AD
3-5-2 NBRGPA022CBFA Nylon bearing 3s 2 2 2 AC
3-5-3 PCOV-A251CBFA Dc cover fr 1 1 1 AC
3-6 FPACGA309CBKZ F-door packing 1 1 1 AX
3-7 HDECQA384CBFA Handle trim fl 1 1 1 AD
3-8 JHNDPA117CBFA Door handle fl 1 1 1 AK
3-9 PCAP-A067CBFA Screw cover hd 10 10 10 AC
3-15 FDORRB166CBKZ R-door ass’y - - 1 BQ
3-15 FDORRB173CBKZ R-door ass’y - 1 - BQ
3-15 FDORRB181CBKZ R-door ass’y 1 - - BP
3-15-1 LSTP-A058CBM0 R-door stopper r 1 1 1 AF
3-15-2 LSTPPA084CBFA Rd-stopper spring r 1 1 1 AD
3-15-3 PCOV-A252CBFA Dc cover rr 1 1 1 AC
3-17 FPACGA310CBKZ R-door packing - - 1 AY
3-17 FPACGA314CBKZ R-door packing - 1 - AY
3-17 FPACGA315CBKZ R-door packing 1 - - AY
3-18 HDECQA385CBFA Handle trim rl 1 1 1 AG
3-19 JHNDPA118CBFA Door handle rl 1 1 1 AK
3-25 FBDGDA280CBYZ Badge ass’y 1 1 1 AY

OTHER PARTS

4-1 LBND-A023CBE0 L-band c 4 4 4 AC
4-3 LX-VZA003CBE0 Special screw 2 2 2 AB
4-10 QTAN-A013CBE0 Solderless term. a 4 4 4 AH
4-15 LX-BZA018CBE0 Special screw 1 1 1 AA
4-17 LX-WZA003CBE0 Washer 4 4 4 AA
4-18 LX-BZA076CBEZ Handle screw 10 10 10 AC

ATTACHMENT PARTS

5-1 UPOK-A166CBRA Bottle pocket 2 2 2 AN
5-3 UPOK-A168CBRA F door pocket 2 2 2 AP
5-4 UPOK-A165CBRA R door pocket 1 1 2 AN
5-5 UTNA-A282CBFB Egg tray 2 2 2 AG
5-6 FSRA-A193CBYZ Ice cube maker 1 1 1 AS
5-9 FSRA-A194CBKZ F shelf ass’y 1 1 1 AY
5-13 HGRL-A178CBFA Ventilating grille 1 1 1 AG
5-14 USRA-A252CBFA Drain pan 1 1 1 AN
5-15 UYOK-A330CBFA Fruit case 1 1 1 AW
5-16 UYOK-A331CBFA Vegetable case 1 1 1 AZ
5-17 UYOK-A328CBFA Ice storage box 1 1 1 AF
5-18 UYOK-A329CBFA Chilled case 1 1 1 AX
5-19 GDORPA066CBRA Chilled door 1 1 1 AP
5-24 FTNA-A301CBKZ R glass shelf ass’y 2 2 3 BC
5-25 FTNA-A302CBKZ V glass shelf ass’y 1 1 1 BC

SJ-58L SJ-63L SJ-68L

-T2G -T2G -T2G

28

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L

-T2G -T2G -T2G

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

5-26 PCAP-A076CBFA Venti.grille cap 1 1 1 AC
5-28 PCAP-A069CBFA V sliding cap l 1 1 1 AC
5-29 PCAP-A070CBFA V sliding cap r 1 1 1 AC
5-31 LRALPA132CBFA Ice tray holder l 1 1 1 AF
5-32 LRALPA133CBFA Ice tray holder r 1 1 1 AF
5-33 LRALPA134CBFA Ice tray holder b 1 1 1 AF
5-34 PCUP-A009CBFA Water cup 1 1 1 AD
5-35 UPOKPA251CBFA Tube stand 2 2 2 AC
5-36 PCOV-A259CBFA Case cover 1 1 1 AH
5-37 UPOK-A167CBRA Utility case pocket 1 1 1 AM

CYCLE PARTS

6-1 PCMPLA196CBE0 Compressor 1 1 - BX
6-1 PCMPLA202CBEZ Compressor - - 1 BX
6-2 PSPAGA028CBE0 Rubber grommet 4 4 4 AD
6-3 FCONSA077CBKZ Sub. condenser ass’y 1 1 1 AX
6-3-1 PCOV-A256CBFA Pipe protector l 1 1 1 AF
6-3-2 PCOV-A257CBFA Pipe protector r 1 1 1 AF
6-4 FFRM-A113CBKZ Base frame ass’y 1 1 1 AW
6-5 FDRY-A006CBK0 Dryer ass’y 1 1 1 AX
6-6 PCLI-A035CBE0 Clip 1 1 1 AC
6-9 PSPAFA020CBE0 Sleeve 4 4 4 AB
6-11 PPIPCA357CBEZ S.p connector 1 1 1 AK
6-15 PGUM-A002CBF0 Absorbent rubber b 1 1 1 AH
6-18 PPIPCA252CBE0 Charge pipe 2 2 2 AD
6-21 PCOVPA165CBE0 Terminal cover 1 1 1 AF
6-27 PSEL-B899CBEZ S-sealer 2 2 2 AC
6-28 PKYU-A143CBEZ S-butyl 1 1 1 AD
6-29 PKYU-A036CBE0 Sp-butyl d-poy 1 1 1 AP
6-30 PKYU-A098CBE0 Compressor butyl 1 1 1 AG
6-31 PKYU-A035CBE0 Sp-butyl h 1 1 1 AG

MISCELLANEOUS

90-1 TINS-A472CBRZ Operation manual 1 1 1 AF
90-2 TLAB-A092CBR0 Lamp label 1 1 1 AD
90-3 SPAKCI794YDEZ Packing case 68l-3 - - 1 BC
90-3 SPAKCI818YDEZ Packing case 58l-3 1 - - BB
90-3 SPAKCI840YDEZ Packing case 63l-3 - 1 - BB
90-5 TLAB-A910CBEZ Case label t2g 4 4 4 AC
90-6 CPADBA765YDKZ Bottom pad ass’y 1 1 1 AY
90-7 CPADBA764YDKZ Top pad ass’y 1 1 1 AR
90-8 TLAB-A876CBRZ Warning label 1 1 1 AC
90-12 TLAB-A885CBRZ Energy label - - 1 AE
90-12 TLAB-A895CBRZ Energy label - 1 - AE
90-12 TLAB-A896CBRZ Energy label 1 - - AE
90-20 TLAB-A939CBRZ Caution label rof 1 1 1 AD

29

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REPLACEMENT PARTS LIST(SJ-58L/63L/68L-T2B,SJ-63L-T2W)

ELECTRIC PARTS

1-1 RTHM-A097CBEZ F-thermostat 1 1 1 1 AX
1-2 RSTT-A144CBE0 Starting relay 1 1 1 1 AW
1-3 QSWTDA035CBE0 Defrost timer 1 1 1 1 BB
1-4 PDMP-A046CBEZ Damper thermo - 1 1 1 AX
1-4 PDMP-A048CBEZ Damper thermo 1 - - - AW
1-5 FTHM-A028CBKZ Defrost thermo.ass’y 1 1 1 1 AN
1-6 RMOTRA040CBE0 Fan motor 1 1 1 1 AZ
1-7 QSOCAA074CBEZ Lamp socket 1 1 1 1 AP
1-8 RLMP-A012CBE0 Lamp 1 1 1 1 AH
1-9 QACC-A097CBE0 Source cord 1 1 1 1 AV
1-10 QSW-PA090CBZA Door switch 1 1 1 1 AS
1-11 RHOG-A084CBE0 Protector 1 1 - 1 AN
1-11 RHOG-A105CBE0 Protector - - 1 - AV
1-17 FFS-TA055CBKZ Fuse ass’y 1 1 1 1 AL
1-20 FW-VZA144CBEZ Lead ev-cover ass’y 1 1 1 1 AK
1-21 FHETBA146CBEZ Def.heater ass’y 1 1 1 1 AZ
1-22 FCNW-A622CBK0 Relay wire ass’y 1 1 1 - AN
1-23 QCNW-A671CBE0 Reray wire rc 1 1 1 - AD
1-25 QTAN-A032CBE0 Terminal block 1 1 1 1 AE
1-27 RMOTRA061CBEZ Fan motor 1 1 1 1 AW
1-28 RLMP-A029CBEZ Lamp15w 1 1 1 1 AH
1-29 QSOCAA072CBEZ Lamp socket 1 1 1 1 AN
1-30 FTHM-A029CBKZ R fan thermo ass’y 1 1 1 1 AQ
1-32 RC-EZA190CBEZ Running capacitor 1 1 1 - AW

MECHANICAL PARTS

2-2 JKNB-A036CBFB F-temp. control knob 1 1 1 1 AD
2-4 LPLTMA568CBEZ Fl plate al. 1 1 1 1 AF
2-7 FLEGPA077CBKZ Leg holder l ass’y 1 1 1 1 AQ
2-7-1 FAJS-A009CBK0 Adjustable leg ass’y 2 2 2 2 AD
2-7-2 LHLD-A533CBPZ Leg holder l 1 1 1 1 AL
2-8 FLEGPA078CBKZ Leg holder r ass’y 1 1 1 1 AQ
2-8-2 LHLD-A534CBPZ Leg holder r 1 1 1 1 AP
2-10 PSPAVA083CBEA Upper hinge spacer 1 1 1 1 AD
2-11 PSPAVA084CBEA Bottom hinge spacer 1 1 1 1 AC
2-12 PSPAVA075CBEA Center hinge spacer 1 1 1 1 AD
2-13 DHNG-A363CBMZ Upper hinge ass’y 1 1 1 1 AE
2-14 DHNG-A365CBMZ Bottom hinge r ass’y 1 1 1 1 AE
2-15 DHNG-A364CBMZ Center hinge r ass’y 1 1 1 1 AF
2-16 GCOV-A191CBFZ E.v cover 1 1 1 1 AS
2-17 LCRA-A010CBE0 Fan clamp 2 2 2 2 AD
2-19 LHLD-A389CBF0 Motor cushion 2 2 2 2 AF
2-20 NFANPA020CBFA Propeller fan 100 1 1 1 1 AE
2-21 PSEL-B845CBEZ E.v cover sealer a 1 1 1 1 AC
2-22 PSEL-B846CBEZ E.v cover sealer b 1 1 1 1 AC
2-23 PSEL-A415CBE0 E.v cover sealer c 1 1 1 1 AC
2-24 PCOVPA164CBFA Terminal cover 1 1 1 1 AE
2-25 PCOV-A253CBFA F lamp cover 1 1 1 1 AC
2-26 PCOV-A254CBFA R lamp cover 1 1 1 1 AF
2-27 GCOVPA119CBRA R-cbox cover 1 1 1 1 AS
2-28 HGRL-A184CBRA Fan louver 1 1 1 1 AU
2-29 GCOV-A162CBFH Upper hinge cover 1 1 1 - AD
2-29 GCOV-A162CBFJ Upper hinge cover - - - 1 AD
2-30 PCOV-A255CBFA Fan cover 2 2 2 2 AD
2-31 JKNB-A033CBFB R-temp.control knob 1 1 1 1 AD
2-36 PCAP-A006CBFW Screw cover - - - 2 AB
2-36 PCAP-A006CBFY Screw cover 2 2 2 - AB
2-37 PCAP-A056CBFF Screw cover b 2 2 2 2 AC
2-38 PGID-A156CBFZ R air guider a 1 1 1 1 AG
2-41 PSEL-B848CBEZ A-sealer thermo.cap 1 1 1 1 AC
2-49 LSTPPA108CBFA Chilled stopper 2 2 2 2 AC
2-50 NFANPA019CBFA Propeller fan 80 1 1 1 1 AM
2-51 PBOX-A121CBFA F lamp box 1 1 1 1 AF
2-52 PBOX-A122CBFA R lamp box 1 1 1 1 AM
2-53 LHLD-A536CBFA R fan motor holder a 1 1 1 1 AF
2-54 LHLD-A537CBFA R fan motor holder b 1 1 1 1 AE
2-55 HGRL-A181CBFA Multi louver l - - 1 - AN
2-55 HGRL-A186CBFA Multi louver m - 1 - 1 AM
2-55 HGRL-A188CBFA Multi louver s 1 - - - AG
2-56 PFPFPB233CBFZ R-louver insu. l - - 1 - AG
2-56 PFPFPB239CBFZ R-louver insu. m - 1 - 1 AF
2-56 PFPFPB248CBFZ R-louver insu. s 1 - - - AE
2-57 PSEL-B843CBEZ A-sealer r-louver - - 2 - AC
2-57 PSEL-B857CBEZ A-sealer r-louver - 2 - 2 AC

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L SJ-63L

-T2B -T2B -T2B -T2W

30

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L SJ-63L

-T2B -T2B -T2B -T2W

2-57 PSEL-B861CBEZ A-sealer r-louver 2--- AC
2-59 PCOV-A264CBEZ F lamp box cover 1111 AC
2-63 LHLD-A484CBFA Fan motor holder b 1111 AH
2-64 LHLD-A485CBFA Fan motor holder a 1111 AH
2-65 PSEL-B209CBE0 U-sealer handle 2222 AB
2-66 PSHEMA132CBP0 Heater cover al 1111 AD
2-67 LPLTMA570CBPZ Drain support al 1111 AE
2-69 PSEL-B847CBEZ E.v cover sealer d 2222 AC
2-71 PSEL-A552CBE0 Dial sealer 1111 AC
2-72 PSEL-B841CBEZ Ra sealer a 2222 AC
2-73 PSEL-B842CBEZ Ra sealer b 1111 AC
2-74 PSEL-B122CBE0 A-sealer thermo.cap. 1111 AB
2-77 LHLD-A391CBE0 Sl-5n clip 1111 AD
2-78 LPLTMA399CBP0 Dryer support 1111 AD
2-79 LBND-A019CBE0 Nylon band 3333 AB
2-80 PBOX-A071CBFA Terminal box 1111 AE
2-81 PPIPPA097CBEZ Drain pipe s 1111 AE
2-83 PSEL-B849CBEZ Ra sealer c 1111 AC
2-84 PSEL-B850CBEZ Ra sealer d 1111 AC
2-87 LBND-A018CBE0 Fastening band a 111- AP
2-90 HGRL-A179CBFA F shower duct 1111 AM
2-91 HGRL-A180CBFA F return cover 2222 AC
2-93 PCAP-A068CBFA C sliding cap a 2222 AC
2-95 NROL-A027CBEZ V roller 2222 AC
2-96 LHLD-A535CBFA Shaft holder 2222 AC
2-97 LPIN-A178CB1Z Shaft 2222 AC
2-99 GCOV-A192CBFC Top cover 111- AD
2-99 GCOV-A192CBFE Top cover ---1 AC
2-105 PSEL-B896CBEZ A-sealer fs-a 1111 AC
2-106 PSEL-B897CBEZ A-sealer fs-b 2222 AC

DOOR PARTS

3-5 FDORFB307CBKZ F-door ass’y 111- BK
3-5 FDORFB308CBKZ F-door ass’y ---1 BH
3-5-1 LSTPPA107CBFA Fd stopper spring r 1111 AD
3-5-2 NBRGPA022CBFA Nylon bearing 3s 2222 AC
3-5-3 PCOV-A251CBFC Dc cover fr 111- AC
3-5-3 PCOV-A251CBFE Dc cover fr ---1 AC
3-6 FPACGA309CBKZ F-door packing 1111 AX
3-7 HDECQA384CBFB Handle trim fl 1111 AG
3-8 JHNDPA117CBFC Door handle fl 111- AN
3-8 JHNDPA117CBFE Door handle fl ---1 AN
3-9 PCAP-A067CBFC Screw cover hd 10 10 10 - AD
3-9 PCAP-A067CBFE Screw cover hd - - - 10 AD
3-15 FDORRB169CBKZ R-door ass’y --1- BP
3-15 FDORRB176CBKZ R-door ass’y -1-- BP
3-15 FDORRB177CBKZ R-door ass’y ---1 BP
3-15 FDORRB184CBKZ R-door ass’y 1--- BN
3-15-1 LSTP-A058CBM0 R-door stopper r 1111 AF
3-15-2 LSTPPA084CBFA Rd-stopper spring r 1111 AD
3-15-3 PCOV-A252CBFC Dc cover rr 111- AC
3-15-3 PCOV-A252CBFE Dc cover rr ---1 AC
3-17 FPACGA310CBKZ R-door packing --1- AY
3-17 FPACGA314CBKZ R-door packing -1-1 AY
3-17 FPACGA315CBKZ R-door packing 1--- AY
3-18 HDECQA385CBFB Handle trim rl 1111 AG
3-19 JHNDPA118CBFC Door handle rl 111- AN
3-19 JHNDPA118CBFE Door handle rl ---1 AN
3-25 FBDGDA280CBYZ Badge ass’y 1111 AY

OTHER PARTS

4-1 LBND-A023CBE0 L-band c 4444 AC
4-3 LX-VZA003CBE0 Special screw 2222 AB
4-10 QTAN-A013CBE0 Solderless term. a 4444 AH
4-15 LX-BZA018CBE0 Special screw 1111 AA
4-17 LX-WZA003CBE0 Washer 4444 AA
4-18 LX-BZA076CBEZ Handle screw 10 10 10 10 AC

ATTACHMENT PARTS

5-1 UPOK-A166CBRA Bottle pocket 2222 AN
5-3 UPOK-A168CBRA F door pocket 2222 AP
5-4 UPOK-A165CBRA R door pocket 1121 AN
5-5 UTNA-A282CBFB Egg tray 2222 AG
5-6 FSRA-A193CBYZ Ice cube maker 1111 AS
5-9 FSRA-A194CBKZ F shelf ass’y 1111 AY

31

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L SJ-63L

-T2B -T2B -T2B -T2W

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

5-13 HGRL-A178CBFC Ventilating grille 1 1 1 - AN
5-13 HGRL-A178CBFE Ventilating grille - - - 1 AN
5-14 USRA-A252CBFA Drain pan 1 1 1 1 AN
5-15 UYOK-A330CBFA Fruit case 1 1 1 1 AW
5-16 UYOK-A331CBFA Vegetable case 1 1 1 1 AZ
5-17 UYOK-A328CBFA Ice storage box 1 1 1 1 AF
5-18 UYOK-A329CBFA Chilled case 1 1 1 1 AX
5-19 GDORPA066CBRA Chilled door 1 1 1 1 AP
5-24 FTNA-A301CBKZ R glass shelf ass’y 2 2 3 2 BC
5-25 FTNA-A302CBKZ V glass shelf ass’y 1 1 1 1 BC
5-26 PCAP-A076CBFC Venti.grille cap 1 1 1 - AD
5-26 PCAP-A076CBFE Venti.grille cap - - - 1 AD
5-28 PCAP-A069CBFA V sliding cap l 1 1 1 1 AC
5-29 PCAP-A070CBFA V sliding cap r 1 1 1 1 AC
5-31 LRALPA132CBFA Ice tray holder l 1 1 1 1 AF
5-32 LRALPA133CBFA Ice tray holder r 1 1 1 1 AF
5-33 LRALPA134CBFA Ice tray holder b 1 1 1 1 AF
5-34 PCUP-A009CBFA Water cup 1 1 1 1 AD
5-35 UPOKPA251CBFA Tube stand 2 2 2 2 AC
5-36 PCOV-A259CBFA Case cover 1 1 1 1 AH
5-37 UPOK-A167CBRA Utility case pocket 1 1 1 1 AM

CYCLE PARTS

6-1 PCMPLA196CBE0 Compressor 1 1 - 1 BX
6-1 PCMPLA202CBEZ Compressor - - 1 - BX
6-2 PSPAGA028CBE0 Rubber grommet 4 4 4 4 AD
6-3 FCONSA077CBKZ Sub. condenser ass’y 1 1 1 1 AX
6-3-1 PCOV-A256CBFA Pipe protector l 1 1 1 1 AF
6-3-2 PCOV-A257CBFA Pipe protector r 1 1 1 1 AF
6-4 FFRM-A113CBKZ Base frame ass’y 1 1 1 1 AW
6-5 FDRY-A006CBK0 Dryer ass’y 1 1 1 1 AX
6-6 PCLI-A035CBE0 Clip 1 1 1 1 AC
6-9 PSPAFA020CBE0 Sleeve 4 4 4 4 AB
6-11 PPIPCA357CBEZ S.p connector 1 1 1 1 AK
6-15 PGUM-A002CBF0 Absorbent rubber b 1 1 1 1 AH
6-18 PPIPCA252CBE0 Charge pipe 2 2 2 2 AD
6-21 PCOVPA165CBE0 Terminal cover 1 1 1 1 AF
6-27 PSEL-B899CBEZ S-sealer 2 2 2 2 AC
6-28 PKYU-A143CBEZ S-butyl 1 1 1 1 AD
6-29 PKYU-A036CBE0 Sp-butyl d-poy 1 1 1 1 AP
6-30 PKYU-A098CBE0 Compressor butyl 1 1 1 1 AG
6-31 PKYU-A035CBE0 Sp-butyl h 1 1 1 1 AG

MISCELLANEOUS

90-1 TINS-A472CBRZ Operation manual 1 1 1 1 AF
90-2 TLAB-A092CBR0 Lamp label 1 1 1 1 AD
90-3 SPAKCI794YDEZ Packing case 68l-3 - - 1 - BC
90-3 SPAKCI818YDEZ Packing case 58l-3 1 - - - BB
90-3 SPAKCI840YDEZ Packing case 63l-3 - 1 - 1 BB
90-5 TLAB-A922CBEZ Case label t2w - - - 4 AC
90-5 TLAB-A938CBEZ Case label t2a 4 4 4 - AC
90-6 CPADBA765YDKZ Bottom pad ass’y 1 1 1 1 AY
90-7 CPADBA764YDKZ Top pad ass’y 1 1 1 1 AR
90-8 TLAB-A876CBRZ Warning label 1 1 1 1 AC
90-12 TLAB-A885CBRZ Energy label - - 1 - AE
90-12 TLAB-A895CBRZ Energy label - 1 - 1 AE
90-12 TLAB-A896CBRZ Energy label 1 - - - AE
90-21 TLAB-A939CBRZ Caution label rof 1 1 1 1 AD

32

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

DOOR PARTS

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

3-6

3-5

3-9

3-8

3-9

4-18

3-5-2

5-3

5-4

5-5

5-1

3-5-3

3-15-3

3-5-1

3-5-2

3-15-2

3-17

5-35

3-15

4-18

4-18

3-9

3-9

5-34

5-36

5-37

3-9

3-9

3-9

4-18

4-18

4-18

4-18

4-18

4-18

4-18

3-9

3-9

3-7

3-19

3-18

3-25

3-9

3-15-1

33

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

CABINET PARTS

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

2-29

2-13

2-99

2-90

2-49

2-49

2-97

2-95

2-95

2-96

2-96

2-91

2-7

2-7-2

2-7-1

2-8

2-8-2

2-7-1

2-11

2-14

5-31

5-17

5-6

5-32

5-33

5-9

5-24

5-14

1-10

2-15

2-37

5-13

5-26

4-3

5-15

5-25

5-16

5-29

5-28

2-93

2-93

5-18

5-19

2-36

2-36

2-12

2-106

2-105

2-10

34

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

CABINET PARTS

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

6-11

6-15

6-1

4-1

2-31

6-9

6-2

4-17

1-2

6-4

6-3

6-3-1

1-9

2-80

2-77

2-24

6-18

6-5

6-18

4-10

2-78

2-66

2-67

2-81

2-4

1-21

1-22

6-21

4-15

1-11

2-2

2-30

2-25

6-3-2

1-29

2-59

2-51

90-2

1-8

2-72

1-4

2-41

2-83

2-73

2-71

2-38

2-74

2-84

2-30

2-79

1-30

1-3

2-27

2-54

1-27

2-53

1-7

1-28

2-52

2-17

90-8

2-57

2-56

2-55

2-26

2-63

2-19

1-6

2-19

2-64

2-20

2-17

2-22

2-23

1-17

4-1

1-5

2-69

1-1

1-20

2-65

2-21

2-16

2-28

2-50

6-27

6-30

6-29

6-28

2-79

1-31

6-6

1-25

2-87

6-31

1-23

35

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

36

SJ-58L-T2
SJ-63L-T2
SJ-68L-T2

52APR3/ 52APB3/ 56APR3/ 56APB3/ 56APW3/ 60APR3/ 60APB3

2000 (08U0.11E) Printed in Japan