Sharp PC817XI2, PC817XI3, PC817XI4, PC817XI5, PC817XI6 Datasheet

...

h November 28, 1995

ELECTRONIC COMPONE

GROUP SHARP

CORPORATION

F \

DEVICE SPECIFICATION FOR

Business dealing name

PHOTOCOUPLER

MODEL No.

PC817

SPECIFICATION

OPTO-ELECTS DEVICES DIV.

1. These specification sheets include the contents under the copyright of Sharp Corporation (“Sharp”]. Please keep them with reasonable care as important information. Please don’t reproduce or cause anyone reproduce them without Sharp’s consent.

2. Please obey the instructions mentioned below for actual use of this device. SHARP takes no responsibility for damage caused by improper use of the devices.

(I) This device is designed for general electronic equipment.

Main uses of this device are as follows;

[

* Computer

- OA equipment - Telecommunication equipment (Terminal)

- Measuring equipment l Tooling machine - AV equipment

Home appliance, etc.

(2) Please take proper steps in order to maintain reliability and safety, in case this device

is used for the uses mentioned below which require high reliability.

- [ Unit concerning control and safety of a vehicle (air plane, train, automobile etc.)

- Traffic signal * Gas leak detection breaker * Fire box and burglar alarm box * Other safety equipment, etc.

(3) Please do not use for the uses mentioned below which require extremely high reliability.

- Space equipment [ * Telecommunication equipment (Trunk) * Nuclear control equipment

* Medical equipment etc.

Contact a SHARP representative of sales office in advance when you intend to use S?%4.RP devices for any applications other than those applications for general electronic equipment recommend by SHARP at (1).

CUSTOMER’S APPROVAL

DATE PRESENTED BY

DATE

T. Matsumura, Department General Manager of Engineering Dept.,11

Opto-Electronic Devices Div.

ELECOM Group SHARP CORPORATION

SHARP CORPORATION

i November 28. 1995 1

1. Application

This specification applies to the outline and characteristics of photocoupler Model No. PC8 17series.

2. Outline Refer to the attached drawing No. CY7073K02.

3. Ratings and characteristics Refer to the attached sheet, page 3 to 6.

4. Reliability Refer to the attached sheet, page 7.

5. Incoming inspection Refer to the attached sheet, page 8.

6. Supplement

6.1 Isolation voltage shall be measured in the following method. (11 Short between anode to cathode on the primary side and between collector

to emitter on the secondary side. (21 The dielectric withstand tester with zero-cross circuit shall be used. (3) The wave form of applied voltage shall be a sine wave.

(It is recommended that the isolation voltage be measured in insulation oil.)

SHARP CORPORATION

6.2 Business dealing name

(” 0” mark indicates business dealing name of ordered product)

Ordered Business

Rank mark Ic (mA)

nroduct dealingname

PC817Xl

A, B, C, D or no mark 2.5 to 30

PC817XIl

A 4.0 to 8.0

PC8 17XI2

B .

6.5 to 13

PC8 17XI3 C

10to20 PC8 17XI4 D PC817XI5 AorB PC8 17Xi6 B or C

15 to 30

4.0to 13 :

6.5 to 20

I I

1 PC817XI7 1

C or D

10 to 30

PC8 172U8 PC8 17XI9

A, B or C B, CorD

4.0 to 20

6.5 to 30

1 PC817XIO 1

A, B, C or D 1 4.oto30

6.3 This Model is approved by UL. Approved Model No. : PC8 17 UL file No. : E64380

6.4 This product is not designed against irradiation. This product is assembled with electrical input and output. This product incorporates non-coherent light emitting diode.

Test

conditions

1,=5mA

vc,=5v

Ta=25’C

7. Notes Refer to the attached sheet- 1 - 1, 2.

Ta=25”C

l 1 Forward current

Collector current Ic 50 mA *l Collector power dissipation

PC 150 mW *l Total power dissipation Ptot 200 mW *3 Isolation voltage

viso

kVrms

Operating temperature

Topr -30 to +lOO ‘C

Storage temperature

Tstg

-55 to +125

“C

*4 Soldering temperature

Tsol 260 “C

‘1 The derating factors of absolute maximum ratings due to ambient temperature

are shown in Fig. 1 to 4.

*2 Pulse width_IlOO ,us, Duty ratio : 0.001 (Refer to Fig. 5) *3 AC for 1 min, 40 to 6O%RH l 4 For 10s

+ 7 hidden pages