Sharp PC814X, PC814X1 Datasheet

Dept.,11
Opto-Electronic Devices Div.
ELECOM Group SHARP CORPORATION
u*
T. Matsumura, Department General Manager of
Engineering
PL“7
3.
Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
BY
DATE PRESENTED BY
(4)
Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
-
Medical equipment
1
*
Nuclear power control equipment
-
Telecommunication equipment (for trunk lines)
-
Space equipment
[
;
(3)
Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as
-
Other safety equipment
1
*
Rescue and security equipment
*
Gas leakage sensor breakers
signals
*
Traffic
-
Transportation control and safety equipment (aircraft, train, automobile etc.)
[
;
*
Computers
1
If the use of the product in the above application areas is for equipment listed in paragraphs (2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as
-
Tooling machines
*
Measuring equipment
*
Telecommunication equipment (Terminal)
-
Home appliances
*
Audio visual equipment
*
OA equipment
[
:
(1)
This product is designed for use in the following application areas
SPECI:
I
FICATION
I
OPTO-ELECTRONIC DEVICES DIV.
DEVICE SPECIFICATION FOR
PHOTOCOUPLER
Business dealing name
MODEL No.
PC814
.
1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”). Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2.
When using this product, please observe the absolute maximum ratings and the Instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
January23,
1998
PAGE
10 Pages
APPROVED BY:
DATE:
ELECTRONIC COMPONENTS GROUP SHARP CORPORATION
REPRESENTATIVE DMSION
ISSUE
SW
.
iy$?
A,
g4fi
.q&l,Li
: /I:
PREPARED BY:
DATE:
SPEC. No.
ED-96 197XB
Ta=25%
vc,=5v
I
.
PC814Xl
A
0.5 to 1.5
1mA
I,=+
(mA1
Test
product
dealing name
conditions
PC8 14X
A or no mark
0.2 to 3.0
(“0”
mark indicates business dealing name of ordered product)
Ordered
Business
Rank mark
Ic
(Ic)
Delivery rank table
that
the isolation voltage be measured in insulation oil.1
6.2 Collector current
(21
The dielectric withstand tester with zero-cross circuit shall be used.
(31 The wave form of applied voltage shall be a sine wave.
(It is recommended
(1) Short between anode and cathode on the primary side, and between collector
and emitter on the secondary side.
CY8543K02.
3.
Ratings and characteristics
Refer to the attached sheet, page 4 to 6.
4.
Reliability
Refer to the attached sheet, page 7.
5.
Outgoing inspection
Refer to the attached sheet, page 8.
6.
Supplement
6.1
Isolation voltage shall be measured in the following method.
spectication
applies to the outline and characteristics of photocoupler
Model No. PC8 14X.
2.
Outline
Refer to the attached drawing No.
SHARP CORPORATION
1.
Application
This
PBBO,
and PBB, are not used
in this device at all.
7. Notes Refer to the attached sheet-l-1.2.
(Methylchloroforml
6.7
Brominated flame retardants Specific brominated flame retardants such as the
-Trichloroethane
tetracbloride,
1.1.1
Halon,
Carbon CFC,,
:
-
component.
Materials for ODS
shaI.I
not contain the following materials. Also, the following materials shall not be used in the production process for this device
-
component
This
photocoupler is designed for AC input..
product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting diode.
6.6
ODS materials
This device
This
:
E64380
6.4
6.5
:
PC8 14X
UL file No.
Z/8
6.3
This Model is approved by UL.
Approved Model No.
PC814X
1
January 23, 1998
MODEL No. PAGE
SHRRP
CORPORATION
ED-96197XB
CY8543K02
PC814X)
Drawing No.
:
l/l
mm
PC814
Name
Outline Dimensions (Business dealing name
shall be
or shall not be marked.
UNIT:
*2)
Factory identification mark
shall be marked according to DIN standard.
0.25g
* 1) 2-digit number
:
Approx.
1-k
l
Z
Pin Nos.
and internal
connection diagram
Product mass
=I-,
Rankmark
Primary side mark
SHARP CORPORATION
Loading...
+ 7 hidden pages